Download Aiwa NSX-DS50 Service manual
Transcript
NSX-DS50 NSX-DS55 U U SERVICE MANUAL COMPACT DISC STEREO SYSTEM BASIC TAPE MECHANISM : ZZM-3 PR3NM BASIC CD MECHANISM : BZG-5 ZD3NM SYSTEM CD CASSEIVER NSX-DS50 CX-NDS50 NSX-DS55 CX-NDS55 SPEAKER REMOTE CONTROLLER SX-NAJ502 SX-R290 SX-C610 RC-BAS10 VS • This Service Manual is the “Revision Publishing” and replaces “Simple Manual” of NSX-DS50 / DS55 <U>, (S/M Code No. 09-014-445-3T1). S/M Code No. 09-017-445-3R1 RE VI SIO DA N TA • If requiring information about the CD mechanism, see Service Manual of BZG-5, (S/M Code No. 09-00C-353-3N2). SPECIFICATIONS MAIN UNIT CX-NDS50 / CX-NDS55 TUNER FM tuning range FM usable sensitivity (IHF) FM antenna terminals AM tuning range AM usable sensitivity AM antenna AMPLIFIER Power output Total harmonic distortion Inputs Outputs CASSETTE DECK Track format Frequency response Recording system Heads CD PLAYER Laser D/A converter Signal-to-noise ratio Harmonic distortion 87.5 MHz to 108 MHz 13.2 dBf 75 ohms (unbalanced) 530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) 350 µV/m Loop antenna Front: 70 W + 70 W (50 Hz - 20 kHz, THD less than 1 %, 6 ohms) 88 W + 88 W (1 kHz, THD less than 10 %, 6 ohms) Rear (Surround): 25 W + 25 W (1 kHz, THD less than 1 %, 8 ohms) 35 W + 35 W (1 kHz, THD less than 10 %, 8 ohms) Center: 25 (1 kHz, THD less than 1 %, 8 ohms) 35 W (1 kHz, THD less than 10 %, 8 ohms) 0.1 % (35 W, 1 kHz, 6 ohms, DIN AUDIO/Front) VIDEO/AUX/DVD: 300 mV (adjustable) DIGITAL IN (PCM/DOLBY DIGITAL) OPTICAL (VIDEO/AUX/DVD): Linear PCM signals (32 kHz, 44.1 kHz and 48 kHz) and Dolby Digital bitstream FRONT SPEAKERS: 6 ohms or more SURROUND SPEAKERS: 8 ohms to 16 ohms CENTER SPEAKER: 8 ohms or more SUB WOOFER: 1 V PHONES: 32 ohms or more 4 tracks, 2 channels stereo 50 Hz - 15 kHz AC bias Deck 1: playback x 1 Deck 2: recording/playback x 1, erase x 1 Semiconductor laser (λ = 780 nm) 1 bit dual 85 dB (1 kHz, 0 dB) 0.05 % (1 kHz, 0 dB) GENERAL Power requirements Power consumption Power consumption in standby mode Dimensions (W x H x D) Weight of main unit 120 V AC, 60 Hz 175 W With ECO mode on: 0.6 W With ECO mode off: 35 W 260 x 326 x 340 mm (101/4 x 127/8 x 131/2 in.) 8.2 kg (18 lbs 1 oz) FRONT SPEAKERS SX-NAJ502 Speaker system Speaker units Impedance Dimensions (W x H x D) Weight 3 way, bass reflex (magnetic shielded) Woofer: 160 mm (63/8 in.) cone Tweeter: 60 mm (23/8 in.) cone Super tweeter: 20 mm (13/16 in.) ceramic 6 ohms 230 x 324 x 253 mm (91/8 x 127/8 x 14 in.) 4.5 kg (9 lbs 15 oz) SURROUND SPEAKERS SX-R290 Speaker system Speaker units Impedance Dimensions (W x H x D) Weight Accessories 1 way, bass reflex Full range: 100 mm (4 in.) cone 8 ohms 150 x 132 x 142 mm (6 x 51/4 x 55/8 in.) 0.8 kg (1 lbs 12 oz) Wall mounting screws (2) CENTER SPEAKER SX-C610 Speaker system Speaker units Impedance Dimensions (W x H x D) Weight 1 way, bass reflex Full range: 100 mm (4 in.) cone 8 ohms 260 x 132 x 216 mm (101/4 x 51/4 x 85/8 in.) 1.0 kg (2 lbs 3 oz) • Design and specifications are subject to change without notice. • The word "BBE"and the "BBE symbol" are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc. • Manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY”, the double-D symbol and "PRO LOGIC" are trademarks of Dolby Laboratories Licensing Corporation. –2– PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING!! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CAUTION Use of controls or adjustments or performance of procedures other than those specified herin may result in hazardous radiation exposure. ATTENTION L’utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations. ADVARSEL s s Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel: Usynlig laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling. Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. VAROITUS! Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saataa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 VARNING! Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1. LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT Precaution to replace Optical block PICK-UP Assy PWB (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in right figure. Solder –3– NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure MAIN C.B 1 Remove the AC power cord. 2 Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 3 Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 4 Contact the same end of the discharging resistor as step 3 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) 5 Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. D101 3 2 Select a discharging resistor referring to the following table. C102 4 2 Fig-1 Charging voltage (V) Discharging (C101, 102) resistor (Ω) 25-48 100 3 87-A00-247-090 49-140 220 5 87-A00-232-090 Rated power (W) C101 Parts number Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”. • Good or no good judgement of the MICROCOMPUTER 1 Turn on the AC main power. 2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good. –4– In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset TE R There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 1 Remove the AC power cord. M IC RO CO M PU FRONT C.B 18 15 C113 % VSS MICROC113 COMPUTER * VDD FRONT C.B Short with tweezers. Fig-2-2 2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. –5– ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI NO. DESCRIPTION REF. NO. PART NO. KANRI NO. DESCRIPTION MAIN C.B IC 87-A21-893-040 87-A20-783-040 87-A21-703-040 87-A21-916-040 87-A21-884-040 C-IC,NJM14558V-TE2 C-IC,BA7762AFS C-IC,SN74LV244APW C-IC,SN74LV125APW C-IC,CS4228A C5 C6 C7 C8 C9 87-012-368-080 87-012-368-080 87-012-368-080 87-012-368-080 87-012-368-080 C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 87-A21-882-030 87-A21-883-040 87-A20-921-040 87-A20-870-010 87-A21-885-040 C-IC,M62466FP C-IC,CS8415A C-IC,SN74LVU04APW IC,GP1F37R C-IC,CS49326 C10 C11 C12 C21 C22 87-012-368-080 87-012-368-080 87-012-368-080 87-A12-780-090 87-A12-780-090 C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F CAP,E 4700-35 M 85 SKR CAP,E 4700-35 M 85 SKR 87-A21-695-010 8B-NCK-601-030 87-A21-831-010 87-A21-928-010 87-070-289-040 IC,LA1845L C-IC,UPD784975AGF-102-3BA IC,SPS-442-1-F1 IC,LC72131D-N C-IC,BU2092F C23 C24 C25 C26 C27 87-A12-779-090 87-A12-779-090 87-A12-095-080 87-A12-095-080 87-A12-095-080 CAP,E CAP,E CAP,E CAP,E CAP,E 87-020-903-010 87-A21-269-010 IC,NJM7805FA IC,EW732 C28 C30 C31 C32 C33 87-A12-095-080 87-010-430-080 87-A12-062-080 87-012-286-080 87-A12-062-080 CAP,E 100-50 SMG CAP, ELECT 100-63 CAP,E 100-10 SMG CAP, U 0.01-25 CAP,E 100-10 SMG 87-026-609-080 87-A30-559-010 87-026-610-080 87-A30-076-080 87-A30-075-080 TR,KTA1266GR TR,CSB1370EF TR,KTC3198GR C-TR,2SC3052F C-TR,2SA1235F C34 C35 C36 C40 C60 87-A12-095-080 87-A12-076-080 87-A12-068-080 87-012-286-080 87-A12-089-080 CAP,E 100-50 SMG CAP,E 22-35 SMG CAP,E 470-16 SMG CAP, U 0.01-25 CAP,E 3.3-50 SMG 87-A30-495-080 87-A30-074-080 87-A30-468-080 87-A30-106-040 87-A30-086-040 TR,2SA1981Y C-TR,RT1P141C C-TR,KRC102S-RTK C-TR,CMBT5551 C-TR,CSD1306E C63 C81 C97 C101 C102 87-A12-071-080 87-A10-918-080 87-010-831-080 87-A12-087-080 87-A12-087-080 CAP,E 47-25 SMG CAP,E 100-16 SMG C-CAP,U,0.1-16F CAP,E 1-50 SMG CAP,E 1-50 SMG 87-A30-256-010 87-A30-255-010 87-A30-107-070 87-A30-484-080 87-A30-494-080 TR,2SD1933 TR,2SB1342 C-TR,CMBT5401 C-TR,KRA102S TR,2SA1980G C110 C111 C112 C113 C121 87-010-831-080 87-A12-088-080 87-A12-088-080 87-A12-075-080 87-A12-088-080 C-CAP,U 0.1-16 Z F CAP,E 2.2-50 SMG CAP,E 2.2-50 SMG CAP,E 10-35 SMG CAP,E 2.2-50 SMG 87-A30-190-080 87-A30-529-010 87-A30-528-010 87-A30-105-080 87-A30-162-010 TR,CC5551 TR,2SD2642 TR,2SB1686 C-TR,RT1P441C FET,2SK2937 C122 C145 C146 C147 C148 87-A12-086-080 87-012-368-080 87-012-368-080 87-012-368-080 87-012-368-080 CAP,E 0.47-50 SMG C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F 87-A30-087-080 87-A30-582-080 87-A30-234-080 87-A30-288-040 89-327-143-080 C-FET,2SK2158 TR,CDA1585BC TR,CSC4115BC C-TR,DTC114YKA C-TR,2SC2714O C155 C170 C171 C173 C201 87-010-831-080 87-012-278-080 87-012-282-080 87-010-759-080 87-012-281-080 C-CAP,U,0.1-16F C-CAP,U 2200P-50 B CAP, U 4700P-50 C-CAP,U, 0.1-25F C-CAP,U 3900P-50 B 87-A30-489-080 C-TR,KRA107S C202 C203 C204 C205 C206 87-012-281-080 87-A12-084-080 87-A12-084-080 87-012-282-080 87-012-282-080 C-CAP,U 3900P-50 B CAP,E 0.22-50 SMG CAP,E 0.22-50 SMG CAP, U 4700P-50 CAP, U 4700P-50 87-A40-839-090 87-A40-291-080 87-A40-838-090 87-A40-553-080 87-A40-778-080 DIODE,G5SBA60L-6088 DIODE,1N4148M(CPT) DIODE,G3SBA60L-6088 DIODE,1N4003 LES ZENER,UZ30BSD C207 C208 C209 C210 C211 87-A12-090-080 87-A12-090-080 87-016-615-080 87-016-615-080 87-A12-078-080 CAP,E 4.7-50 SMG CAP,E 4.7-50 SMG C-CAP,U 2.2P-50CH C-CAP,U 2.2P-50CH CAP,E 47-35 SMG 87-A40-764-080 87-A40-270-080 87-A40-269-080 87-A40-488-080 87-A40-202-080 ZENER,UZ10BSC C-DIODE,MC2838 C-DIODE,MC2836 DIODE,1SS244 ZENER,UZ5.1BSB C212 C215 C216 C217 C218 87-A12-078-080 87-012-273-080 87-012-273-080 87-A10-596-080 87-A10-596-080 CAP,E 47-35 SMG C-CAP,U 820P-50 B C-CAP,U 820P-50 B C-CAP,S 100P-100 J CH C-CAP,S 100P-100 J CH 87-A40-749-080 87-A40-393-090 87-A40-748-080 87-A40-747-080 87-A40-745-080 ZENER,UZ5.6BSB DIODE,1N5402GW(F20) ZENER,UZ5.6BSA ZENER,UZ5.1BSB ZENER,UZ4.7BSA C219 C220 C221 C222 C223 87-012-368-080 87-012-368-080 87-012-286-080 87-012-286-080 87-A10-596-080 C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,S 100P-100 J CH 87-A40-739-080 87-017-149-080 ZENER,UZ 2.7BSA ZENER,HZS6A2L C224 C273 C274 87-A10-596-080 87-010-759-080 87-A12-091-080 C-CAP,S 100P-100 J CH C-CAP,U, 0.1-25F CAP,E 10-50 SMG TRANSISTOR DIODE –6– 0.1-50 0.1-50 0.1-50 0.1-50 0.1-50 F F F F F 3300-50 M 85 SKR 3300-50 M 85 SKR 100-50 SMG 100-50 SMG 100-50 SMG REF. NO. PART NO. C275 C301 C301 C302 C303 KANRI NO. 87-A12-091-080 87-012-278-080 87-012-188-080 87-012-188-080 87-012-268-080 DESCRIPTION CAP,E 10-50 SMG C-CAP,U 2200P-50 B C-CAP,U 47P-50 CH C-CAP,U 47P-50 CH C-CAP,U 330P-50 B C304 C305 C306 C307 C309 87-012-268-080 87-012-268-080 87-012-268-080 87-010-759-080 87-010-759-080 C310 C311 C312 C313 C314 REF. NO. C689 C701 C702 C703 C707 KANRI NO. 87-A12-058-080 87-012-195-080 87-012-195-080 87-012-286-080 87-A12-088-080 CAP,E 470-6.3 M SMG C-CAP,U 100P-50CH C-CAP,U 100P-50CH CAP, U 0.01-25 CAP,E 2.2-50 SMG C-CAP,U 330P-50 B C-CAP,U 330P-50 B C-CAP,U 330P-50 B C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C708 C772 C782 C783 C784 87-A12-088-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-286-080 CAP,E 2.2-50 SMG CAP, U 0.01-25 CAP, U 0.01-25 CAP, U 0.01-25 CAP, U 0.01-25 87-010-759-080 87-010-787-080 87-010-787-080 87-012-276-080 87-012-276-080 C-CAP,U, 0.1-25F CAP, U 0.022-25 CAP, U 0.022-25 CAP, CHIP SS 1500 PBK CAP, CHIP SS 1500 PBK C785 C786 C788 C789 C790 87-012-286-080 87-012-286-080 87-012-167-080 87-A12-052-080 87-A12-052-080 CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U 5P-50 CH C-CAP,S 0.033-25 J B C-CAP,S 0.033-25 J B C315 C316 C321 C322 C324 87-012-278-080 87-012-278-080 87-012-142-080 87-012-142-080 87-A12-071-080 C-CAP,U 2200P-50 B C-CAP,U 2200P-50 B CAP, S 0.33-16 CAP, S 0.33-16 CAP,E 47-25 SMG C791 C792 C793 C795 C796 87-010-831-080 87-012-286-080 87-A12-090-080 87-012-286-080 87-012-286-080 C-CAP,U,0.1-16F CAP, U 0.01-25 CAP,E 4.7-50 SMG CAP, U 0.01-25 CAP, U 0.01-25 C325 C327 C328 C332 C333 87-A12-057-080 87-A12-090-080 87-A12-090-080 87-010-759-080 87-016-251-080 CAP,E 330-6.3 SMG CAP,E 4.7-50 SMG CAP,E 4.7-50 SMG C-CAP,U, 0.1-25F CAP,E 220-16 M SMG C797 C798 C799 C800 C801 87-A12-091-080 87-012-286-080 87-A12-093-080 87-010-829-080 87-A12-089-080 CAP,E 10-50 SMG CAP, U 0.01-25 CAP,E 33-50 SMG CAP, U 0.047-16 CAP,E 3.3-50 SMG C335 C336 C337 C339 C340 87-A12-087-080 87-A12-087-080 87-010-759-080 87-010-759-080 87-010-759-080 CAP,E 1-50 SMG CAP,E 1-50 SMG C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C802 C803 C803 C804 C807 87-010-829-080 87-010-787-080 87-012-280-080 87-A12-062-080 87-A12-086-080 CAP, U 0.047-16 CAP, U 0.022-25 CAP, U 3300P-50 CAP,E 100-10 SMG CAP,E 0.47-50 SMG C351 C352 C354 C355 C356 87-012-270-080 87-012-270-080 87-012-271-080 87-012-274-080 87-A12-071-080 CAP, U 470P-50 CAP, U 470P-50 CAP, U 560P-50 CHIP CAP,U 1000P-50B CAP,E 47-25 SMG C808 C809 C810 C814 C815 87-A12-087-080 87-A12-087-080 87-010-831-080 87-012-286-080 87-A12-086-080 CAP,E 1-50 SMG CAP,E 1-50 SMG C-CAP,U,0.1-16F CAP, U 0.01-25 CAP,E 0.47-50 SMG C357 C358 C359 C360 C363 87-012-286-080 87-012-279-080 87-012-279-080 87-012-279-080 87-A12-361-080 CAP, U 0.01-25 C-CAP,U 2700P-50 B C-CAP,U 2700P-50 B C-CAP,U 2700P-50 B CAP,M 5600P-100 J CP C816 C821 C823 C824 C825 87-A12-086-080 87-A12-091-080 87-010-177-080 87-A12-090-080 87-010-596-080 CAP,E 0.47-50 SMG CAP,E 10-50 SMG C-CAP,S 820P-50 SL CAP,E 4.7-50 SMG CAP, S 0.047-16 C370 C373 C374 C378 C379 87-010-759-080 87-A10-060-080 87-A10-060-080 87-010-759-080 87-A12-069-080 C-CAP,U, 0.1-25F C-CAP,S 0.18-16 K B C-CAP,S 0.18-16 K B C-CAP,U, 0.1-25F CAP,E 22-25 SMG C831 C842 C844 C850 C851 87-010-406-080 87-012-286-080 87-012-286-080 87-A12-071-080 87-012-286-080 CAP, ELECT 22-50 CAP, U 0.01-25 CAP, U 0.01-25 CAP,E 47-25 SMG CAP, U 0.01-25 C380 C386 C388 C391 C392 87-A12-069-080 87-010-759-080 87-012-266-080 87-012-191-080 87-012-191-080 CAP,E 22-25 SMG C-CAP,U, 0.1-25F C-CAP,U 220P-50 B C-CAP,U 56P-50 J CH C-CAP,U 56P-50 J CH C852 C853 C858 C859 C860 87-012-286-080 87-012-286-080 87-010-831-080 87-010-759-080 87-012-286-080 CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U,0.1-16F C-CAP,U, 0.1-25F CAP, U 0.01-25 C393 C394 C619 C621 C622 87-012-191-080 87-012-191-080 87-010-831-080 87-012-278-080 87-012-278-080 C-CAP,U 56P-50 J CH C-CAP,U 56P-50 J CH C-CAP,U,0.1-16F C-CAP, U 2200P-50 K B C-CAP, U 2200P-50 K B C913 C918 C959 C960 C961 87-012-286-080 87-A10-039-080 87-010-831-080 87-010-831-080 87-012-167-080 CAP, U 0.01-25 C-CAP,U 470P-50 J CH C-CAP,U 0.1-16F C-CAP,U,0.1-16F C-CAP,U 5P-50 CH C633 C634 C635 C636 C637 87-012-281-080 87-016-369-080 87-012-281-080 87-016-369-080 87-A12-088-080 C-CAP,U 3900P-50 C-CAP,S 0.033-25 C-CAP,U 3900P-50 C-CAP,S 0.033-25 CAP,E 2.2-50 SMG C963 C971 C972 C973 C974 87-015-785-080 87-A12-067-080 87-A12-090-080 87-012-286-080 87-012-286-080 CHIP CAPACITOR, 0.1FZ-25Z CAP,E 330-16 SMG CAP,E 4.7-50 SMG CAP, U 0.01-25 CAP, U 0.01-25 C638 C656 C675 C676 C683 87-A12-088-080 87-A10-260-080 87-012-282-080 87-012-282-080 87-A11-969-080 CAP,E 2.2-50 SMG C-CAP,U 0.1-16 K B CAP, U 4700P-50 CAP, U 4700P-50 C-CAP,U 0.082U-16 K B C979 C981 C982 C983 C984 87-012-195-080 87-A12-071-080 87-010-831-080 87-012-286-080 87-012-286-080 C-CAP,U 100P-50CH CAP,E 47-25 SMG C-CAP,U,0.1-16F CAP, U 0.01-25 CAP, U 0.01-25 C684 C685 C686 C687 C688 87-A12-075-080 87-012-167-080 87-010-759-080 87-010-759-080 87-A12-062-080 CAP,E 10-35 SMG C-CAP,U 5P-50 CH C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F CAP,E 100-10 SMG C987 C991 C992 C993 C995 87-012-286-080 87-012-176-080 87-012-176-080 87-012-274-080 87-012-274-080 CAP, U 0.01-25 CAP 15P CAP 15P CHIP CAP,U 1000P-50B CHIP CAP,U 1000P-50B B B K B B K –7– PART NO. DESCRIPTION REF. NO. PART NO. C997 C998 C999 CF831 CF832 KANRI NO. 87-010-831-080 87-A12-071-080 87-A11-155-080 87-008-261-010 87-008-261-010 DESCRIPTION C-CAP,U,0.1-16F CAP,E 47-25 SMG CAP,TC U 0.01-16 Z F FILTER, SFE10.7MA5 FILTER, SFE10.7MA5 CN105 CN183 CN301 CN351 CN601 87-099-195-010 87-099-564-010 87-A60-620-010 87-A60-625-010 87-099-719-010 CN701 CN703 CNA1 CNA102 CNA602 C501 C502 C503 C504 C601 KANRI NO. 87-012-195-080 87-012-195-080 87-012-195-080 87-010-759-080 87-010-382-040 C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U, 0.1-25F CAP,E 22-25 SME CONN,7P V BLK 6216 CONN,4P V TUC-P4P-B1 CONN,3P V 2MM JMT CONN,8P V 2MM JMT CONN,30P H BLK(X) C801 C802 C803 C804 C805 87-A10-804-080 87-010-316-080 87-012-280-080 87-A10-592-080 87-012-184-080 C-CAP,S C-CAP,S C-CAP,U C-CAP,S C-CAP,U 87-A60-061-010 87-010-385-040 8A-NF6-646-010 8A-NF8-655-010 87-A60-632-010 CONN,06P V 9604S-06C CAP,E 220-25 M SME CONN ASSY,9P TID-A(460) CONN ASSY,7P TID-A(150) CONN 15P V 2MM JMT C806 C807 C808 C809 C810 87-012-274-080 87-012-274-080 87-010-544-040 87-010-404-040 87-016-114-080 CHIP CAP,U 1000P-50B CHIP CAP,U 1000P-50B CAP,E 0.1-50 SME CAP,E 4.7-50 SME C-CAP,U0.01-25B FFC105 FFC701 FFE831 J101 J102 88-907-121-110 88-906-251-110 A8-6ZA-19M-030 87-A60-929-010 87-A60-238-010 FF-CABLE,7P 120 FF-CABLE,6P 1.25 6ZA-1 YFEMENM JACK,DIA6.3 BLK ST W/S TAI TERMINAL,SP 4P (MSC) C811 C901 C902 C903 C904 87-A12-052-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 C-CAP,S C-CAP,U C-CAP,U C-CAP,U C-CAP,U 0.033-25 J B 100P-50CH 100P-50CH 100P-50CH 100P-50CH J603 J831 L141 L142 L301 87-A60-881-010 87-A60-202-010 87-A50-610-010 87-A50-610-010 87-A50-625-010 JACK,PIN 2P MSP 242V05 PBSN TERMINAL,ANT 4P MSP-154V-02 COIL,1UH K(MDEC) COIL,1UH K(MDEC) COIL,TRAP 85KHZ (SANWA) C905 C906 C907 C908 C909 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 C-CAP,U C-CAP,U C-CAP,U C-CAP,U C-CAP,U 100P-50CH 100P-50CH 100P-50CH 100P-50CH 100P-50CH L302 L351 L801 L802 L811 87-A50-625-010 87-007-342-010 87-A50-608-010 87-A91-552-010 87-005-847-080 COIL,TRAP 85KHZ (SANWA) COIL,OSC 85KHZ BIAS COIL,FM DET-N(TOK) FLTR,MT-450AL(TOK) COIL,2.2UH K CECS C910 C911 C912 C913 C914 87-012-195-080 87-012-274-080 87-010-759-080 87-A11-242-040 87-A11-242-040 C-CAP,U 100P-50CH CHIP CAP,U 1000P-50B C-CAP,U, 0.1-25F CAP,E 220-10 M 5L SRM CAP,E 220-10 M 5L SRM L832 L909 L951 R85 R86 87-005-847-080 87-A91-639-010 8A-NF8-667-010 87-A00-436-050 87-A00-436-050 COIL,2.2UH K CECS TRANS,BALUN FM COIL,AM PACK 4(TOK) RES,100-1/2W J RP RES,100-1/2W J RP C915 C916 C917 C919 C920 87-010-759-080 87-010-759-080 87-010-759-080 87-012-286-080 87-010-757-080 C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F CAP, U 0.01-25 C.CAP,U 0.047-25F R87 R88 R149 R150 R151 87-A00-436-050 87-A00-436-050 87-A01-001-050 87-A01-001-050 87-A01-001-050 RES,100-1/2W RES,100-1/2W RES,220-1/2W RES,220-1/2W RES,220-1/2W C921 C951 C952 C953 C961 87-012-282-080 87-012-176-080 87-012-198-080 87-A10-039-080 87-010-378-040 CAP, U 4700P-50 C-CAP,U 15P-50 J CH C-CAP,U 180P-50 J CH C-CAP,U 470P-50 J CH CAP,E 10-16 R152 R255 R256 R259 R260 87-A01-001-050 87-A00-262-080 87-A00-262-080 87-A00-262-080 87-A00-262-080 RES,220-1/2W J BLT2J RES,M/F 0.15-2W J RES,M/F 0.15-2W J RES,M/F 0.15-2W J RES,M/F 0.15-2W J C962 C963 CN104 CN701 CN731 87-012-157-080 87-010-759-080 87-A60-057-010 87-099-720-010 87-099-196-010 C-CAP,S 330P-50 CH C-CAP,U, 0.1-25F CONN,11P V 9604S-11C CONN,30P BLK B(P) CONN,8P V BLK 6216 R790 R991 R993 R995 SFR351 87-012-286-080 87-012-195-080 87-012-195-080 87-012-195-080 87-A90-433-080 CAP, U 0.01-25 C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U 100P-50CH SFR,50K H NVZ6TLTA CN732 FFC104 FFC731 FFC732 FL901 87-099-014-010 88-911-101-110 88-908-301-110 88-912-371-110 8B-NCK-605-010 CONN,12P V BLK 6216 FF-CABLE, 11P 1.25 FF-CABLE, 8P 1.25 FF-CABLE,12P 1.25 37 FL,HNA-08MM29 SFR352 TH201 TH202 WH1 WH102 87-A90-433-080 87-A91-042-080 87-A91-042-080 87-A90-510-010 87-A90-460-010 SFR,50K H NVZ6TLTA C-THMS,100K 55001 C-THMS,100K 55001 HLDR,WIRE 2.5-9P HLDR,WIRE 2.5-7P L951 LED201 LED202 LED203 LED204 87-A50-652-010 87-A40-606-040 87-A40-606-040 87-A40-606-040 87-A40-606-040 COIL,OSC 15.6MHZ LED,SLR-332VC LED,SLR-332VC LED,SLR-332VC LED,SLR-332VC X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST LED209 S321 S322 S323 S324 87-A40-317-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 LED,SLR-342VCT31 RED SW,TACT EVQ11G04M SW,TACT EVQ11G04M SW,TACT EVQ11G04M SW,TACT EVQ11G04M C153 C154 C155 C156 C301 87-010-787-080 87-A12-078-040 87-010-404-040 87-010-404-040 87-012-278-080 CAP, U 0.022-25 CAP,E 47-35 SMG CAP,E 4.7-50 SME CAP,E 4.7-50 SME C-CAP,U 2200P-50 K B S325 S326 S327 S328 S329 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M C351 C361 C362 C371 C372 87-A10-201-080 87-012-274-080 87-012-274-080 87-012-274-080 87-012-274-080 C-CAP,S 0.33-16 K B CHIP CAP,U 1000P-50B CHIP CAP,U 1000P-50B CHIP CAP,U 1000P-50B CHIP CAP,U 1000P-50B S330 S331 S332 S333 S334 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M J J J J J REF. NO. RP RP BLT2J BLT2J BLT2J FRONT C.B –8– PART NO. DESCRIPTION 0.1-25 J B 33P-50 CH 3300P-50 K B 0.015-50 33P-50 CH REF. NO. PART NO. S335 S341 S342 S343 S344 KANRI NO. 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 DESCRIPTION SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M S345 S346 S347 S348 S349 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M S361 S371 87-A92-172-010 87-A92-057-010 C101 C102 C103 C104 C105 REF. NO. C216 C217 C219 C221 C223 KANRI NO. 87-A11-538-080 87-012-277-080 87-012-277-080 87-012-282-080 87-A12-091-080 C-CAP,S 0.12-25 J B C-CAP,U 1800P-50 K B GRM C-CAP,U 1800P-50 K B GRM CAP, U 4700P-50 CAP,E 10-50 SMG C224 C401 C404 C503 C504 87-A12-091-080 87-A10-260-080 87-A10-260-080 87-A12-088-080 87-A12-088-080 CAP,E 10-50 SMG C-CAP,U 0.1-16 K B C-CAP,U 0.1-16 K B CAP,E 2.2-50 SMG CAP,E 2.2-50 SMG SW,RTRY EC12E24204-25MM OFF SW,RTRY EC12E12504-25MM OFF C505 C506 C507 C508 C511 87-A12-090-080 87-A12-090-080 87-A12-090-080 87-A12-090-080 87-012-275-080 CAP,E 4.7-50 SMG CAP,E 4.7-50 SMG CAP,E 4.7-50 SMG CAP,E 4.7-50 SMG C-CAP,U 1200P-50 87-A12-091-080 87-A12-091-080 87-012-172-080 87-012-172-080 87-010-831-080 CAP,E 10-50 SMG CAP,E 10-50 SMG CAPACITOR CHIP U 10P CH CAPACITOR CHIP U 10P CH C-CAP,U,0.1-16F C512 C513 C551 C552 C553 87-012-275-080 87-A10-918-080 87-A10-047-080 87-A10-047-080 87-010-831-080 C-CAP,U 1200P-50 CAP,E 100-16 SMG C-CAP,U 1-10 Z F C-CAP,U 1-10 Z F C-CAP,U 0.1-16 Z F C106 C107 C108 C113 C114 87-010-831-080 87-A12-091-080 87-A12-091-080 87-012-268-080 87-012-268-080 C-CAP,U,0.1-16F CAP,E 10-50 SMG CAP,E 10-50 SMG C-CAP,U 330P-50 B C-CAP,U 330P-50 B C601 C602 C603 C604 C606 87-A12-091-080 87-A10-260-080 87-A12-091-080 87-A10-260-080 87-012-195-080 CAP,E 10-50 SMG C-CAP,U 0.1-16 K B CAP,E 10-50 SMG C-CAP,U 0.1-16 K B C-CAP,U 100P-50CH C115 C116 C117 C118 C119 87-012-284-080 87-012-284-080 87-012-277-080 87-012-277-080 87-012-282-080 CAP, U 6800P-50 CAP, U 6800P-50 C-CAP,U 1800P-50 CH C-CAP,U 1800P-50 CH CAP, U 4700P-50 C617 C618 C621 C624 C651 87-A12-087-080 87-010-831-080 87-A12-091-080 87-A10-260-080 87-016-251-080 CAP,E 1-50 SMG C-CAP,U,0.1-16F CAP,E 10-50 SMG C-CAP,U 0.1-16 K B CAP,E 220-16 M SMG C120 C121 C122 C123 C124 87-012-282-080 87-012-277-080 87-012-277-080 87-A12-091-080 87-A12-091-080 CAP, U 4700P-50 C-CAP,U 1800P-50 CH C-CAP,U 1800P-50 K B GRM CAP,E 10-50 SMG CAP,E 10-50 SMG C653 C654 C655 C656 C657 87-010-831-080 87-010-831-080 87-A12-087-080 87-A12-091-080 87-010-831-080 C-CAP,U,0.1-16F C-CAP,U,0.1-16F CAP,E 1-50 SMG CAP,E 10-50 SMG C-CAP,U,0.1-16F C125 C126 C151 C152 C153 87-A10-902-080 87-A12-091-080 87-A12-091-080 87-A12-091-080 87-012-172-080 C-CAP,U 0.47-10 K B CAP,E 10-50 SMG CAP,E 10-50 SMG CAP,E 10-50 SMG CAPACITOR CHIP U 10P CH C658 C659 C701 C702 C703 87-010-831-080 87-010-831-080 87-012-195-080 87-A11-969-080 87-010-831-080 C-CAP,U,0.1-16F C-CAP,U,0.1-16F C-CAP,U 100P-50CH C-CAP,S 0.082U-16 K B C-CAP,U,0.1-16F C154 C155 C156 C157 C161 87-012-172-080 87-010-831-080 87-010-831-080 87-A10-902-080 87-012-268-080 CAPACITOR CHIP U 10P CH C-CAP,U,0.1-16F C-CAP,U,0.1-16F C-CAP,U 0.47-10 K B C-CAP,U 330P-50 B C704 C706 C707 C709 C711 87-012-278-080 87-012-180-080 87-012-180-080 87-012-180-080 87-010-831-080 C-CAP,U 2200P-50 C-CAP,U 470-50 J C-CAP,U 470-50 J C-CAP,U 470-50 J C-CAP,U,0.1-16F C162 C163 C164 C165 C166 87-012-268-080 87-010-831-080 87-010-831-080 87-012-284-080 87-012-284-080 C-CAP,U 330P-50 B C-CAP,U,0.1-16F C-CAP,U,0.1-16F CAP, U 6800P-50 CAP, U 6800P-50 C712 C715 C721 C722 C723 87-A12-062-080 87-012-286-080 87-012-167-080 87-012-167-080 87-010-831-080 CAP,E 100-10 SMG CAP, U 0.01-25 C-CAP,U 5P-50 CH C-CAP,U 5P-50 CH C-CAP,U,0.1-16F C167 C168 C169 C170 C171 87-012-277-080 87-012-277-080 87-012-277-080 87-012-277-080 87-012-282-080 C-CAP,U 1800P-50 C-CAP,U 1800P-50 C-CAP,U 1800P-50 C-CAP,U 1800P-50 CAP, U 4700P-50 C751 C801 C802 C804 C805 87-012-278-080 87-010-831-080 87-012-286-080 87-012-270-080 87-A12-088-080 C-CAP,U 2200P-50 B C-CAP,U,0.1-16F CAP, U 0.01-25 CAP, U 470P-50 CAP,E 2.2-50 SMG C172 C173 C174 C201 C202 87-012-282-080 87-A12-091-080 87-A12-091-080 87-A12-091-080 87-A12-091-080 CAP, U 4700P-50 CAP,E 10-50 SMG CAP,E 10-50 SMG CAP,E 10-50 SMG CAP,E 10-50 SMG C810 C818 C819 C820 C823 87-012-267-080 87-010-831-080 87-A12-062-080 87-010-831-080 87-010-831-080 C-CAP,U 270P-50 B C-CAP,U,0.1-16F CAP,E 100-10 SMG C-CAP,U,0.1-16F C-CAP,U,0.1-16F C203 C204 C205 C206 C207 87-012-172-080 87-012-274-080 87-010-831-080 87-010-831-080 87-A10-902-080 CAPACITOR CHIP U 10P CH CHIP CAP,U 1000P-50B C-CAP,U,0.1-16F C-CAP,U,0.1-16F C-CAP,U 0.47-10 K B C824 C825 C826 C828 CN101 87-A12-087-080 87-A12-087-080 87-A12-087-080 87-018-127-080 87-009-551-010 CAP,E 1-50 SMG CAP,E 1-50 SMG CAP,E 1-50 SMG CAP,TC U 470P-50 K B CONN,15P V PH C211 C212 C213 C214 C215 87-012-268-080 87-016-115-080 87-010-831-080 87-010-831-080 87-012-284-080 C-CAP,U 330P-50 B C-CAP,U 0.012-25 J B C-CAP,U,0.1-16F C-CAP,U,0.1-16F CAP, U 6800P-50 CN402 CN651 FB601 FB602 FB701 87-A60-056-010 87-049-919-010 87-008-372-080 87-008-372-080 87-008-372-080 CONN,12P V 9604S-12C CONN,3P V WHT EH FILTER, EMI BL OIRNI FILTER, EMI BL OIRNI FILTER, EMI BL OIRNI AC3 C.B K K K K B B B B GRM GRM GRM GRM –9– PART NO. DESCRIPTION B CH CH CH REF. NO. FB702 FB801 FB802 X701 PART NO. KANRI NO. 87-008-372-080 87-008-372-080 87-008-372-080 87-A70-115-010 DESCRIPTION REF. NO. C101 C102 C103 C104 C107 87-012-278-080 87-012-278-080 87-A12-087-080 87-A12-087-080 87-A12-095-080 C-CAP,U 2200P-50 B C-CAP,U 2200P-50 B CAP,E 1-50 SMG CAP,E 1-50 SMG CAP,E 100-50 SMG C108 C111 C112 C113 C114 87-A12-095-080 87-A12-078-080 87-A12-078-080 87-012-195-080 87-012-195-080 CAP,E 100-50 SMG CAP,E 47-35 SMG CAP,E 47-35 SMG C-CAP,U 100P-50CH C-CAP,U 100P-50CH C117 C118 C119 C120 C121 87-A10-596-080 87-A10-596-080 87-012-368-080 87-012-368-080 87-012-286-080 C-CAP,S 100P-100 J CH C-CAP,S 100P-100 J CH C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F CAP, U 0.01-25 C122 C125 C201 C202 C204 87-012-286-080 87-010-831-080 87-012-278-080 87-A12-087-080 87-A12-095-080 CAP, U 0.01-25 C-CAP,U,0.1-16F C-CAP,U 2200P-50 B CAP,E 1-50 SMG CAP,E 100-50 SMG C206 C207 C209 C210 C211 87-A12-078-080 87-012-195-080 87-A10-596-080 87-012-368-080 87-012-286-080 CAP,E 47-35 SMG C-CAP,U 100P-50CH C-CAP,S 100P-100 J CH C-CAP,S 0.1-50 F CAP, U 0.01-25 C300 C301 C714 CN102 CN104 87-012-278-080 87-012-282-080 87-012-286-080 87-A61-109-010 87-A60-060-010 C-CAP,U 2200P-50 B CAP, U 4700P-50 CAP, U 0.01-25 CONN,7P V TID-A CONN,07P V 9604S-07C R157 R158 R161 R162 R230 87-A00-258-080 87-A00-258-080 87-A00-258-080 87-A00-258-080 87-A00-258-080 RES,M/F RES,M/F RES,M/F RES,M/F RES,M/F R231 TH101 TH102 TH201 W201 87-A00-258-080 87-A91-042-080 87-A91-042-080 87-A91-042-080 8B-NCK-607-010 RES,M/F 0.22-1W J C-THMS,100K 55001 C-THMS,100K 55001 C-THMS,100K 55001 F-CABLE,6P 2.5 130MM WH201 87-A90-508-010 HLDR,WIRE 2.5-6P KANRI NO. DESCRIPTION PT C.B FILTER, EMI BL OIRNI FILTER, EMI BL OIRNI FILTER, EMI BL OIRNI VIB,XTAL 12.288MHZ AMP C.B PART NO. ! ! ! C1 CN1 PT1 PT2 RY2 87-A10-831-010 87-A61-110-010 8B-NCK-612-010 8B-MA6-671-010 87-A91-418-010 CAP,E 1000-25 M SMG CONN,9P V TID-A PT BNC-19 U PT,SUB BMA U (VRK) RELAY,AC12V G5PA-1-M ! ! T1 T2 87-A60-317-010 87-A60-317-010 TERMINAL, 1P MSC TERMINAL, 1P MSC 87-A12-087-080 87-010-379-080 87-A12-071-080 87-009-030-010 87-A60-688-010 CAP,E 1-50 SMG CAP,E 22-16 M 11L SME CAP,E 47-25 SMG CONN,2P V WHT PH CONN,4P H GRY TUC-P04X-C1 8B-NCK-610-010 CONN ASSY,3P BNC-K C401 C402 C403 C404 C411 87-012-368-080 87-012-368-080 87-012-368-080 87-012-368-080 87-012-368-080 C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C412 J201 L401 L402 L411 87-012-368-080 87-A61-540-010 87-A50-610-010 87-A50-610-010 87-A50-610-010 C-CAP,S 0.1-50 F JACK,PIN 4P ORBW MSP-244V -41 COIL,1UH K(MDEC) COIL,1UH K(MDEC) COIL,1UH K(MDEC) WH401 87-A90-508-010 HLDR,WIRE 2.5-6P CN1 CNA351 SFR1 SOL1 SOL2 87-099-753-010 86-ZM3-605-110 87-024-581-010 82-ZM3-627-010 82-ZM3-627-010 CONN,11P H 9604 CONN ASSY,8P-RPB SFR,3.3K H KVSF637A SOL ASSY,27 SO SOL ASSY,27 SO SW1 SW2 SW3 SW4 SW5 87-A90-673-010 87-A90-673-010 87-A90-673-010 87-A90-673-010 87-A90-673-010 SW,MICRO SW,MICRO SW,MICRO SW,MICRO SW,MICRO FAN C.B C180 C181 C182 CN181 CN184 VM2 C.B CNA004 JACK C.B 0.1-50 0.1-50 0.1-50 0.1-50 0.1-50 F F F F F DET C.B 0.22-1W 0.22-1W 0.22-1W 0.22-1W 0.22-1W J J J J J DECK C.B – 10 – ESE11SH1C ESE11SH1C ESE11SH1C ESE11SH1C ESE11SH1C CHIP RESISTOR PART CODE Chip Resistor Part Coding 8 8 A Figure Resistor Code Value of resistor Chip resistor L W t :A Resistor Code : A 1.0 0.5 0.35 104 1.6 0.8 0.45 108 2 1.25 0.45 118 3.2 1.6 0.55 128 Dimensions (mm) Wattage 1/16W Type 1005 Symbol CJ Tolerance 5% 1/16W 1/10W 1608 2125 5% 5% CJ CJ 1/8W 3216 5% CJ Form L t W TRANSISTOR ILLUSTRATION E C B CDA1585BC KTA1266GR KTC3198GR E C B B C E E C B 2SA1980G 2SA1981Y CC5551 CSB1370EF CSC4115BC D G B S B C E G D S 2SB1342 2SB1686 2SD1933 2SD2642 2SK2937 2SK2158 – 11 – C E 2SA1235F 2SC2714O 2SC3052F CMBT5401 CMBT5551 CSD1306E DTC114YKA KRA102S KRA107S KRC102S-RTK RT1P141C RT1P441C WIRING – 1 (MAIN / FAN / VM2) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U – 12 – SCHEMATIC DIAGRAM – 1 (MAIN 1 / 4 / FAN) – 13 – SCHEMATIC DIAGRAM – 2 (MAIN 2 / 4 : TUNER) – 14 – SCHEMATIC DIAGRAM – 3 (MAIN 3 / 4 : AMP) – 15 – SCHEMATIC DIAGRAM – 4 (MAIN 4 / 4 : DECK) – 16 – WIRING – 2 (FRONT) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U – 17 – SCHEMATIC DIAGRAM – 5 (FRONT / DECK) – 18 – WIRING – 3 (AC3) <1 / 2> 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 A B C D E F G H I J K L M N O P Q R S T U – 19 – 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 WIRING – 3 (AC3) <2 / 2> 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U – 20 – SCHEMATIC DIAGRAM – 6 (AC3 / VM2) – 21 – WIRING – 4 (AMP / JACK / DET) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U – 22 – SCHEMATIC DIAGRAM – 7 (AMP / JACK / DET) – 23 – WIRING – 5 (PT) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U – 24 – SCHEMATIC DIAGRAM – 8 (PT) – 25 – WIRING 6 (DECK) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 A TO FRONT C.B CN104 J DECK C.B SW5 (FFC104) 11 9 SW4 10 8 7 5 6 3 4 1 B SW3 SW1 SW2 L (REA) (CST2) C 2 CN1 (CAM2) 1 H + (CAM1) (CST1) D E 1 IC2 3 SFR1 SOL2 1 R1 SOL1 IC1 F 3 G H W1 + H L M1 TAPE MOTOR I J K L M N O P Q R S T U 26 IC BLOCK DIAGRAM – 27 – – 28 – FL (HNA-08MM29) GRID ASSIGNMENT AND ANODE CONNECTION GRID ASSIGNMENT – 29 – ANODE CONNECTION (UP) (DOWN) – 30 – IC DESCRIPTION IC, µPD784975AGF-102-3BA Pin No. Pin Name I/O Description 1 AVDD – Power supply. 2 I-HOLD I Power failure detected input. 3 I-CDSW I CD mecha switch A/D converter input. 4 I-SPEANA_1 I A/D input for spectrum analyser level display. 5 I-SPEANA_2 I A/D input for spectrum analyser level display. 6 I-SPEANA_3 I A/D input for spectrum analyser level display. 7 I-KEY1 I Key A/D input 1. 8 I-KEY2 I Key A/D input 2. 9 I-TU_SIG I Tuner signal input. (Not used) 10 I-5VMISO I IC, CS8415A data input. 11 I-2VMISO I IC, CS49326 data input. 12 I-SUBQ I CD SUBQ data input. 13 I-DISH I CD turntable photo sensor input A/D converter input. 14 AVSS – GND. 15 VSS1 – GND. 16 X1 – 15.6MHz oscillator circuit. 17 X2 – 15.6MHz oscillator circuit. 18 VDD1 – Power supply. 19 IC – Internal connection (connected to GND). 20 I-RMC I System remote control signal input. 21 O-POWER O System power supply ON/OFF output. 22 I-WRQ I CD interrupt signal input. 23 I-DRF I CD focus ON detect data input. 24 CODECCSN O IC, CS4228A chip select output. 25 O-5VDSPCSN O IC, CS49326 chip select output. 26 O-5VMOSI O IC, CS8415A, IC, CS4228A, IC, CS49326 data output. 27 I-RDS_CLK I Tuner RDS clock input. (Not used) 28 O-5VSCK O IC, CS8415A, IC, CS4228A, IC, CS49326 serial clock output. 29 NC - Not connected. 30 O-STB O MAIN PWB strobe output. 31 DIRCSN O IC, CS8415A chip select output. 32 O-5VMRESET O IC, CS8415A, IC, CS4228A reset output. 33 O-SOL1 O DECK1 solenoid ON/OFF output. 34 O-SOL2 O DECK2 solenoid ON/OFF output. 35 I-HPMUTE I Headphone MUTE input. 36 I-8415EMPH I Not used. 37 O-KSCAN O Switch SCAN timing output. 38 I-8415INT I IC, CS8415A INT input. 39 O-MUTE O System MUTE ON/OFF output. 40 VSS0 – GND. 41 VDD0 – Power supply. 42 RESET – System reset input (ON/OFF). 43 I-RDS_DATA I Tuner RDS data input. (Not used) – 31 – Pin No. Pin Name I/O Description 44 O-DSC/O-DATA O Function IC / Tuner IC, data output. 45 I-STEREO I Tuner STEREO detect input. 46 I-IFC I Tune IF count serial data input. 47 O-5VDSPRESET O IC, CS49326 reset output. 48 I-2VINTREQ I IC, CS49326 INT input. 49 NC – Not connected. 50 O-STB(SHIFT) O Shift register strobe output. 51 O-PLL_CLK O PLL IC clock enable output. 52 O-PLL_CE O PLL IC chip enable output. 53, 54 P1, P2 O FL segment P1, P2 output. 55 O-CD_CLK O CD clock output. 56 O-CD_DATA O CD data output. 57 O-CD_CE O CD chip enable output. 58 P3 O FL segment P3 output. 59 I-JOG_B I Dial jog rotary encoder input B. 60 I-JOG_A I Dial jog rotary encoder input A. 61 I-VOL_B I Volume rotary encoder input B. 62 I-VOL_A I Volume rotary encoder input A. 63 P4/AM10K O/I 64 I-TM_BASE I 65 P5/I-AMST O/I FL segment P5 output / AM stereo diode input (Not used). 66 P6/I-LW O/I FL segment P6 output / LW diode input (Not used). 67 P7/I-AUTO2 O/I FL segment P7 output / DECK2 AUTO STOP switch data input. 68 P8/I-AUTO1 O/I FL segment P8 output / DECK1 AUTO STOP switch data input. 69 P9/I-CST2 O/I FL segment P9 output / DECK2 cassette detect switch data input. 70 P10/I-CST1 O/I FL segment P10 output / DECK1 cassette detect switch data input. 71 P11/CAM2 O/I FL segment P11 output / DECK2 CAM switch data input. 72 P12/I-CAM1 O/I FL segment P12 output / DECK1 CAM switch data input. 73 P13/I-REB O/I FL segment P13 output / DECK2 side B record OK switch data input (Not used). 74 P14/I-REA O/I FL segment P14 output / DECK2 side A record OK switch data input. 75 P15/OIRT O/I FL segment P15 output / OIRT diode input (Not used). 76 P16/RDS O/I FL segment P16 output / RDS input to diode (Not used). 77 P17/R+1 O/I FL segment P17 output / DECK R+1 diode input (Not used). 78 P18/DEMO O/I FL segment P18 output / DEMO diode input (Not used). 79 VDD2 – Power supply. 80 VLOAD – Power supply for FL display. 81 P19/C-JACK O/I FL segment P19 output / C-JACK data input (Not used). 82 P20/ECO-OFF O/I FL segment P20 output / ECO-OFF data input (Not used). 83 P21/DTS O/I FL segment P21 output / DTS diode input (Not used). 84 P22/SW O/I FL segment P22 output / SW diode input (Not used). 85 ~ 92 P23 ~ P30 O FL segment P23 ~ P30 output. 93 ~ 100 G1 ~ G8 O FL grid G1 ~ G8 output. FL segment P4 output / AM10K diode input (Not used). Base input for clock. – 32 – ADJUSTMENT <TUNER / FRONT / DECK> < TUNER SECTION > < DECK SECTION > 1. Clock Frequency Check Settings : • Test point : TP2(CLK) Method : Set to AM 1710kHz and check that the test point is 2160kHz ± 45Hz. 9. Tape Speed Adjustment (DECK 2) Settings : • Test tape : TTA–100 • Test point : TP8(Lch), TP9(Rch) • Adjustment location : SFR1 Method : Play back the test tape and adjust SFR1 so that the frequency counter reads 3000Hz ± 5Hz. 2. AM VT Check Settings : • Test point : TP1(VT) Method : Set to AM 1710kHz and check that the test point is less than 8.5V. Then set to AM 530kHz and check that the test point is more than 0.6V. 3. FM VT Check Settings : • Test point : TP1(VT) Method : Set to FM 87.5MHz and check that the test point is more than 0.5V. Then set to FM 108.0MHz and check that the test point is less than 8.0V. 4. AM Tracking Adjustment Settings : • Test point : TP8(Lch), TP9(Rch) • Adjustment location : L951(1/3) Method : Set to AM 1000kHz and adjust L951(1/3) to maximum. 13. REC/PB Frequency Response Adjustment (DECK 2) Settings : • Test tape : TTA–602 • Test point : TP8(Lch), TP9(Rch) • Input signal : 1kHz / 8kHz (LINE IN) • Adjustment location : SFR351 (Lch) SFR352 (Rch) Method : Apply a 1kHz signal and REC mode. Then adjust OSC attenuator so that the output level at the TP8, TP9 becomes -20VU (21mV). Record and play back the 1kHz and 8kHz signals and adjust SFRs so that the output of the 8kHz signals becomes 0dB ± 0.5dB with respect to that of the 1kHz signal. 6. AM IF Adjustment Settings : • Test point : TP8(Lch), TP9(Rch) • Adjustment location : L802 ............................................................ 450kHz. 7. DC Balance / Mono Distortion Adjustment Settings : • Test point : TP3, TP4 (DC Balance) TP8(Lch), TP9(Rch) (Distortion) • Adjustment location : L801 • Input level : 60dBµV Method : Set to FM 98.0MHz and adjust L801 so that the distortion becomes minimum. Next, check that the voltage between TP3 and TP4 is 0V ± 500mV. < FRONT SECTION > µ-CON 11. PB Frequency Response Check (DECK 1, DECK 2) Settings : • Test tape : TTA–330 • Test point : TP8(Lch), TP9(Rch) Method : Play back the 315Hz and 8kHz signals of the test tape and check that the output ratio of the 8kHz signal with respect to that of the 315Hz signal is within 3dB. 12. PB Sensitivity Check (DECK 1, DECK 2) Settings : • Test tape : TTA–200 • Test point : TP8(Lch), TP9(Rch) Method : Play back the test tape and check that the output level of the test point is 280mV ± 3dB. 5. FM Tracking Check Settings : • Test point : TP8(Lch), TP9(Rch) Method : Set to FM 98.0MHz and check that the test point is less than 13dBµV. 8. 10. Head Azimuth Adjustment (DECK 1, DECK 2) Settings : • Test tape : TTA–330 • Test point : TP8(Lch), TP9(Rch) • Adjustment location : Azimuth adjustment screw Method : Play back (FWD) the 8kHz signal of the test tape and adjust screw so that the output becomes maximum. Next, perform on REV PLAY mode. OSC Adjustment Settings : • Test point : TP11(KEY-SCAN), (GND) • Adjustment location : L951 Method : Connect a frequency counter across TP11(KEY-SCAN) and GND. Insert AC plug while pressing TUNER function key and POWER key. Then adjust L951 so that the test point becomes 67.708Hz ± 0.068Hz. To manual reset press POWER key while pressing CLEAR key. 14. REC/PB Sensitivity Check (DECK 2) Settings : • Test tape : TTA–602 • Test point : TP8(Lch), TP9(Rch) • Input signal : 8kHz (LINE IN) Method : Apply a 8kHz signal and REC mode. Then adjust OSC attenuator so that the output level at TP8, TP9 becomes 0VU (210mV). Record and play back the 8kHz signal and check that the output is -1dB ± 3.5dB. – 33 – CD TEST MODE 1. How to Start the CD Test Mode While pressing the FUNCTION button, insert the AC plug to the power outlet. When the test mode is started, the message [CD TEST] is displayed. 2. How to Exit the CD Test Mode Press the POWER button or disconnect the AC plug. * When any key other than PRESET is pressed during play mode, the machine exits the test mode. 3. Function Descriptions and Application of the CD Test Mode No Mode 1 Start mode Operation Display Function All indicators light • All FL indicators light Checking item • FL check • Microprocessor check 2 Search CLEAR mode button READING • LD illuminates all the time • APC circuit check • Focus search continuous • Laser current measurement operations *1 • Focus search waveform check • Spindle motor continuous kick • Focus error waveform check (DRF in the search mode is ignored) 3 Play mode PRESET Normal button • Normal playback • Each servo circuit is checked • If TOC cannot be read, focus • DRF check search is continued 4 Traverse SET mode button Normal • Tracking servo OFF/ON • Tracking balance check • Each time PAUSE button is pressed, the tracking servo repeats turning OFF/ON 5 Sled mode UP button CD TEST • Pickup moves to the inner circumference *2 • Sled circuit check • Tracking circuit check At the same time, lens kicks to • Mechanism operation check the inner circumference DOWN button CD TEST • Pickup check • Pickup moves to the outer circumference *2 At the same time, lens kicks to the outer circumference 6 Spindle mode REC/REC All indicators light • The spindle motor rotates MUTE forward (rough speed) by button pressing the button and • Spindle circuit • Spindle motor rotates backward by pressing one more time and stops by pressing again *1: The driver IC heats up and the protection circuit starts working when the focus search is continued for 10 minutes or longer. There can be a case that operations cannot be performed correctly. In such a case, turn off the main power. After cooling down the machine, restart the machine. *2: Be careful not to damage the gear because the sled motor rotates while the UP or DOWN button is being pressed even if the pick-up is located in the innermost track or the outermost track. – 34 – MECHANICAL EXPLODED VIEW 1 / 1 A BZG-5 ZD3NM 47 A L PWB A A A 24 50 PWB 45 WIRE, BINDER M 48 C 32 A 44 A 49 43 F A 31 J PWB 22 FL901 30 PWB M WIRE, BINDER 40 N C 37 G 34 54 15 42 17 18 I 23 19 D 53 H O 46 A 1 A A 20 48 A A 16 WIRE, BINDER HT-SINK, FIN T2 A PWB 35 2 HT-SINK,S 41 O O 25 A PWB H 51 N I A 52 5 46 3 39 A 6 20 N A A 13 14 26 38 E 27 28 7 21 B 8 4 10 33 28 27 PLATE,EATH MECH 29 ZZM-3 PR3NM A K 36 9 CHAS,MAIN 11 12 – 35 – J MECHANICAL PARTS LIST 1 / 1 REF. NO. PART NO. 1 2 3 3 4 8B-NFK-008-010 8B-NFK-013-010 8B-NCK-011-010 8B-NCK-013-010 8B-NFK-033-010 KANRI DESCRIPTION NO. PANEL,TRAY WINDOW,TRAY WINDOW,DISP U<50> WINDOW,DISP U DS55<55> PANEL,FR U 5 6 7 8 9 8B-NCK-006-010 8B-NFK-024-010 8A-NF8-281-010 8B-NFK-003-010 8B-NFK-011-010 10 11 12 13 14 REF. NO. PART NO. KANRI DESCRIPTION NO. AC CORD ASSY,U BLK HLDR,PWB PNRM R HLDR,TR 1 HLDR,PWB PNRM F HLDR,PWB AMP 39 40 41 42 43 87-A80-149-010 8B-NF7-236-010 8B-NCK-206-010 8B-NF7-235-010 8B-NCK-209-010 KEY,ASSY FUNCTION DD KEY,CD SPR-T,EJECT 1 BOX,CASS 1 WINDOW,CASS 1 1WAY 44 45 46 47 48 8B-NCK-202-010 8B-NCK-208-010 87-064-185-010 87-084-079-010 87-A90-457-010 HLDR,PWB DD HLDR,TR AMP HLDR,WIRE RIVET,NYL 4-5 F-BEAD,15-25-15 E251 8A-NF8-282-010 8B-NFK-004-010 8B-NFK-012-010 8B-NFK-014-010 8B-NFK-015-010 SPR-T,EJECT 2 BOX,CASS 2 WINDOW,CASS 2 KNOB,RTRY VOL KNOB,RTRY JOG 49 50 51 52 53 87-A90-173-010 8B-NCK-210-010 8B-NF7-238-010 87-A92-117-010 88-912-371-110 F-BEAD,9-20-21 ZCAT HLDR,TR AMP ST HLDR,FAN LOW FAN,ASB0812H(DELTA)-400MM FF-CABLE,12P 1.25 37 15 16 17 18 19 8B-NFK-016-010 8B-NFK-029-010 8B-NCK-021-010 8B-NFK-018-010 8B-NFK-026-010 KEY,POWER LENS,SENSOR KEY,DOLBY KEY,PLAY 1WAY KEY,ENTER 54 A B C D 88-907-121-110 87-067-703-010 87-067-688-010 87-NF4-224-010 87-723-096-410 FF-CABLE,7P 120 TAPPING SCREW, BVT2+3-10 BVTT+3-6 S-SCREW,IT3B+3-8 CU QT2+3-10W/O SLOT BL 20 21 22 23 24 8Z-NF6-210-010 8B-NCK-001-010 8B-NFK-201-010 88-908-301-110 88-906-251-110 DMPR,150 N CABI,FR U GUIDE,FL FF-CABLE,8P 1.25 FF-CABLE,6P 1.25(RVS-FACE) E F G H I 87-721-096-410 8A-NF7-251-010 87-067-689-010 87-078-200-010 87-721-097-410 QT2+3-10 GLD W,3.2-8-0.45 TAPPING SCREW, BVTT+3-8 S-SCREW,ITC+4-8 R QT2+3-12 GLD 25 26 27 28 29 88-911-101-110 87-NF4-216-010 86-NF9-224-010 82-NF5-229-010 87-NF4-217-110 FF-CABLE,11P 1.25 HLDR,LOCK 1 SPR-C,LOCK PLATE,LOCK HLDR,LOCK 2 J K L M N 87-067-641-010 87-067-698-010 87-067-758-010 87-067-585-010 87-067-579-010 UTT2+3-8(W/O SLOT)BL BVT2+3-18(W/O,SLOT) BVT2+3-12 W/O SLOT BVTT+4-6 BVT2+3-8 W/O SLOT 30 31 32 33 34 8B-NFK-006-010 8B-NFK-040-010 8A-NF8-206-010 8A-NHZ-021-010 8A-DB8-209-010 PANEL,LEFT PANEL,TOP HLDR,PWB M FOOT,H20 HLDR,PWB PT O 87-B10-315-010 BVIT3B+3-8 R W/O 35 36 37 37 38 8B-NFK-027-010 8B-NCK-008-010 8B-NCK-031-010 8B-NCK-032-010 87-A91-422-010 REFLECTOR,ECO PANEL,RIGHT BNC-19 PANEL,REAR USM<50> PANEL,REAR USM DS55<55> BUSHING,AC CORD(U) ! COLOR NAME TABLE Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green YM Metallic Yellow DM Metallic Orange PT Transparent Pink LA Aqua Blue GL Light Green HT Transparent Gray – 36 – TAPE MECHANISM EXPLODED VIEW 1 / 1 TERMINAL, LB1 33 A 34 55 A 44 45 43 36 42 31 32 41 46 51 TERMINAL,LB1 33 45 51 35 A 52 44 52 31 32 b a 29 43 47 29 40 39 28 48 50 42 53 46 49 35 41 30 27 37 47 B 38 21 a 48 40 19 27 49 20 26 25 b 24 17 23 18 16 22 28 30 21 26 20 25 24 19 IC, EW732 23 18 22 IC, EW732 54 9 5 6 38 1 14 54 39 2 10 11 c c 5 6 3 37 9 14 15 16 PWB 10 7 11 12 8 4 12 15 13 – 37 – 13 TAPE MECHANISM PARTS LIST 1 / 1 31 32 33 34 35 8Z-ZM3-233-010 84-ZM2-227-310 87-A92-198-010 87-A90-404-010 8Z-ZM3-239-010 KANRI DESCRIPTION NO. SPR-T,BRG M3 SPR-C,AZIMUTH HEAD,PH HASVH 2504A HEAD,EH LE15B SPR-E,FR GEAR,CAM TD20 FLY-WHL ASSY,M3 R FLY-WHL ASSY,M3 L SPR-T,TRIG CLR,MG 36 37 38 39 40 8Z-ZM3-211-010 8Z-ZM3-225-010 8Z-ZM3-221-010 8Z-ZM3-234-010 8Z-ZM3-223-010 LEVER,EJECT R LEVER,STOP LEVER,CAS SPR-T,LVR CAS SPR-C,REEL R M3 82-ZM3-616-010 8Z-ZM3-243-010 8Z-ZM3-238-010 8Z-ZM3-219-010 8Z-ZM3-206-010 RING MAGNET 4 LEVER ASSY,HD UP SPR-T,HD UP GEAR,CAM M3 LEVER,TRIG 41 42 43 44 45 8Z-ZM1-225-110 8Z-ZM3-240-010 8Z-ZM3-237-010 8Z-ZM3-215-010 8Z-ZM1-261-110 GEAR,REEL R SPR-T,T-UP M3 SPR-T,PINCH M3 LEVER,PINCH M3 ROLLER ASSY,PINCH 16 17 18 19 20 8Z-ZM3-209-010 8Z-ZM3-203-010 8Z-ZM1-228-010 8Z-ZM1-265-010 8Z-ZM1-227-010 LEVER,CAM FR CHAS ASSY,M3 GEAR,SLIP T-UP B FELT,T-UP GEAR,SLIP T-UP A 46 47 48 49 50 8Z-ZM1-226-010 8Z-ZM3-222-010 8Z-ZM3-251-010 8Z-ZM3-236-010 82-ZM1-240-110 GEAR,REEL L SPR-C,REEL L M3 GEAR,IDL REW M3 SPR-T,PLAY M3 LVR,REC(*) 21 22 23 24 25 8Z-ZM1-251-110 8Z-ZM1-275-010 8Z-ZM1-257-010 8Z-ZM1-236-010 8Z-ZM3-226-010 SPR-C,T-UP SLIP W-L,1,47-4-0.25 SPR-C,F/R CLR,SLIP FF/REW SPR-C,FR M3 51 52 53 54 55 8Z-ZM3-216-010 87-B10-301-010 8Z-ZM3-212-010 8Z-ZM3-214-010 86-ZM3-605-110 LEVER,T-UP M3 W-L,1.63-3.2-05 SLIT LEVER,EJECT L HLDR,IC CONN ASSY,8P -RPB 26 27 28 29 30 8Z-ZM3-250-010 8Z-ZM1-269-010 8Z-ZM1-238-110 8Z-ZM3-220-010 8Z-ZM3-205-010 GEAR,SLIP F/R A M3 FELT,FF/REW 2 GEAR,SLIP FF/REW B 2 LEVER,FR M3 LEVER,PLAY M3 A B 84-ZM2-242-010 8Z-ZM2-220-110 S-SCREW,AZ1-2-6.4 V+2.6 ZZM-2 REF. NO. PART NO. 1 2 3 4 5 8Z-ZM3-227-010 8Z-ZM3-235-010 8Z-ZM1-235-010 87-045-347-010 8Z-ZM1-232-010 6 7 8 9 10 8Z-ZM3-244-010 8Z-ZM3-256-010 8Z-ZM3-255-010 8Z-ZM3-231-010 8Z-ZM3-213-010 11 12 13 14 15 REF. NO. PART NO. KANRI DESCRIPTION NO. BELT,MAIN M3 BELT,MAIN L PULLEY,MOT MOT,SHU2L 70 GEAR,IDL FF/REW – 38 – GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) Type.1 Type.4 TOOLS Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units. 1 Plastic head hammer 2 (() flat head screwdriver 3 Cut chisel 1 2 3 How to Remove the PANEL, FR Type.2 Remove the grill frame and four pieces of rubber caps by pulling out with a flat-bladed screwdriver. Remove the screws from hole where installed rubber caps. Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units. 1. Insert the (() flat head screwdriver tip into the gap between the PANEL, FR and the PANEL, SPKR. Tap the head of the (() flat head screwdriver with the plastic hammer head, and create the clearance as shown in Fig-1. 2. Insert the cut chisel in the clearance, and tap the head of the cut chisel with plastic hammer as shown in Fig-2, to remove the PANEL, FR. 3. Place the speaker horizontally. Tap head of the cut chisel with plastic hammer as shown in Fig-3, and remove the PANEL, FR completely. Type.3 Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into one of the hollows around speaker unit, and then remove the speaker unit. After replacing the speaker unit, install it turning to clockwise direction until "click" sound comes out. Fig-1 Fig-2 Fig-3 How to Attach the PANEL, FR Attach the PANEL, FR to the PANEL, SPKR. Tap the four corners of the PANEL, FR with the plastic hammer to fit the PANEL, FR into the PANEL, SPKR completely. – 39 – SPEAKER PARTS LIST SX-NAJ502 (YUSC,YUSC9,YUSL) REF. NO. PART NO. 1 2 3 4 4 KANRI DESCRIPTION NO. 8B-NS0-001-010 PANEL,FR 8B-NS0-003-010 GRILLE,FRAME ASSY 8B-NS0-008-010 PROTECTOR,TW 8B-NSK-602-010 SPKR,W 160<YUSC> 8B-NS0-602-010 SPKR,W 160 30/4<YUSC9,YUSL> 5 6 7 87-NSH-612-010 87-NS7-611-010 8B-NSK-604-010 SPKR,CERAMIC ASSY CORD,SPKR SPKR,T 60 SPEAKER PARTS LIST SX-R290 (YUSC) REF. NO. PART NO. 1 2 3 4 5 KANRI DESCRIPTION NO. 8B-YS1-003-010 PANEL,FR 8B-YS1-002-010 PROTECTOR,ASSY 81-VSA-009-010 CORD,BUSH 87-YS6-002-010 SPKR,CORD Y 8B-YS1-602-010 SPKR,100 L 6 87-010-384-010 CAP,E 100-25 M SME SPEAKER PARTS LIST SX-C610 (YUSC) REF. NO. PART NO. 1 2 3 4 5 KANRI DESCRIPTION NO. 8B-YS2-002-010 PANEL,REAR 8B-YS2-003-010 PROTECTOR,ASSY 81-VSA-009-010 CORD,BUSH 83-NSM-010-010 SPKR,CORD 8B-YS2-604-010 SPKR,100 L ACCESSORIES / PACKAGE LIST REF. NO. PART NO. 1 2 3 4 KANRI DESCRIPTION NO. 8B-NCK-903-010 IB,U(ESF)M 87-043-115-010 ANT,FEEDER FM 87-006-268-010 ANT LOOP,AM 8B-NCK-702-010 RC UNIT,RC-BAS10 VS – 40 – 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9820543 9301978 921338 Printed in Singapore