Download Service instructions

Transcript
CR(E) 45
CR(E) 45-1-1
CR(E) 45-1
CR(E) 45-2-2
CR(E) 45-2
CR(E) 45-3-2
CR(E) 45-3
CR(E) 45-4-2
CR(E) 45-4
CR(E) 45-5-2
CR(E) 45-5
CR(E) 45-6-2
CR(E) 45-6
CR(E) 45-7-2
CR(E) 45-7
CR(E) 45-8-2
CR(E) 45-8
CR(E) 45-9-2
CR(E) 45-9
CR(E) 45-10-2
CR(E) 45-10
CR(E) 45-11-2
CR(E) 45-11
CR(E) 45-12-2
CR(E) 45-12
CR(E) 45-13-2
CR(E) 64
96397558
96397559
96397560
96307228
96397561
96307229
96397562
96307230
96397563
96397564
96397565
96397566
96397567
96397568
96397569
96397570
96397571
96397572
96397573
96397574
96397575
96397576
96397577
96397578
96397579
CR(E) 64-1-1
CR(E) 64-1
CR(E) 64-2-2
CR(E) 64-2-1
CR(E) 64-2
CR(E) 64-3-2
CR(E) 64-3-1
CR(E) 64-3
CR(E) 64-4-2
CR(E) 64-4-1
CR(E) 64-4
CR(E) 64-5-2
CR(E) 64-5-1
CR(E) 64-5
CR(E) 64-6-2
CR(E) 64-6-1
CR(E) 64-6
CR(E) 64-7-2
CR(E) 64-7-1
CR(E) 64-7
CR(E) 64-8-2
CR(E) 64-8-1
CR(E) 90
96397580
96397581
96397582
96397583
96397584
96397585
96397586
96397587
96307231
96397588
96397589
96397590
96397591
96397592
96397593
96397594
96397595
96397596
96397597
96397598
96397599
96397600
CR(E) 90-1-1
CR(E) 90-1
CR(E) 90-2-2
CR(E) 90-2
CR(E) 90-3-2
CR(E) 90-3
CR(E) 90-4-2
CR(E) 90-4
CR(E) 90-5-2
CR(E) 90-5
CR(E) 90-6-2
CR(E) 90-6
96397601
96397602
96397603
96397604
96397605
96307232
96397606
96397607
96397608
96397609
96397610
96397611
Table 6 “Pump Data” GSC files
2. Select the file from the ‘Configuration files’ field, and press ‘Send’.
3. Check that the selected configuration file number is now shown in the label in the PC Tool, Standard
Configuration under ‘5.Pump Data’, indicating that the CU 351 has received and stored the file. See fig. 19.
96307032
2. C-MPC options
96592488
3. Hydro MPC
96307209
4. H-MPC options 5. Pump data
96592497
96307221
CONFIGURATION STEPS - PLEASE FOLLOW THE NUMBERS
96586126
TM04 2155 2108
1. Control MPC
Fig. 19 “Pump data” on GSC files label
4. Restart the CU 351 unit by pressing, “Restart” in the right bottom of the PC Tool.
Note
When “Restart” is pressed, the CU 351 will initialise.
A progress bar indicating how far the initialisation is in per cent appears in the display. This procedure will take about
25 sec.
5.2.3 Configuration of external frequency converters, if any
The manufacturer's factory settings of the external frequency converter(s) used in MPC F, EF and EDF must be
changed to the Grundfos settings before the MPC is ready for test.
To configure the external frequency converter:
1. Turn on the power supply to the frequency converter(s) by means of the automatic circuit breaker.
2. For each frequency converter, do the settings as described in the table below.
41 / 47