Download INSTRUCTION MANUAL

SPECIFICATIONS
15
■ Receiver
■ Antenna tuner
• Receive system
:Double superheterodyne system
• Intermediate frequencies
1st
:64.455 MHz
2nd
:36 kHz
• Sensitivity
SSB, CW
:0.16 µV (1.80–29.99 MHz)*4
(10 dB S/N) BW=2.4 kHz 0.13 µV (50.0–54.0 MHz)*5
AM (10 dB S/N)
:12.6 µV (0.5–1.799 MHz)*4
BW=6 kHz
2.0 µV (1.80–29.99 MHz)*4
1.6 µV (50.0–54.0 MHz)*5
FM (12 dB SINAD)
:0.5 µV (28.0–29.7 MHz)*4
BW=15 kHz 0.32 µV (50.0–54.0 MHz)*5
• Squelch sensitivity
• Matching impedance range
HF bands
:1
6.7 to 150 ø unbalanced
Frequency band
HF
50 MHz
*4 Preamp 1 is ON.
Squelch sensitivity
SSB : Less than 5.6 µV*4
FM : Less than 0.32 µV*4
SSB : Less than 5.6 µV*5
FM : Less than 0.32 µV*5
*5 Preamp 2 is ON.
• Selectivity (IF filter shape is set to SHARP.)
:More than 2.4 kHz/–6 dB
SSB (BW: 2.4 kHz)
Less than 3.4 kHz/–40 dB
:More than 500 Hz/–6 dB
CW (BW: 500 Hz)
Less than 700 Hz/–40 dB
:More than 500 Hz/–6 dB
RTTY (BW: 350 Hz)
Less than 800 Hz/–40 dB
:More than 6.0 kHz/–6 dB
AM (BW: 6 kHz)
Less than 10.0 kHz/–40 dB
:More than 12.0 kHz/–6 dB
FM (BW: 15 kHz)
Less than 22.0 kHz/–40 dB
• Spurious and image rejection ratio
:More than 70 dB
• AF output power :More than 2.0 W at 10%
distortion with an 8 ø load
(at 13.8 V DC)
• RIT variable range :±9.999 kHz
• PHONES connector
:3-conductor 6.35 (d) mm (1⁄4″)
• External SP connector : 2-conductor 3.5 (d) mm
(1⁄8″)/8 ø
• DSP ANF attenuation :More than 30 dB
(with 1 kHz single tone)
• DSP MNF attenuation :More than 70 dB
• DSP NR attenuation
:More than 6 dB
(noise rejection in SSB)
(Less than VSWR 1:3)
50 MHz band
:2
0 to 125 ø unbalanced
(Less than VSWR 1:2.5)
• Minimum operating input : 8 W (HF bands)
power
15 W (50MHz band )
• Tuning accuracy
: VSWR 1:1.5 or less
• Insertion loss (after tuning at RF power 100W)
1.8 MHz band
:1
.2 dB or less
Bands other than 1.8 MHz : 1.0 dB or less
1
All stated specifications are typical and subject to change without
notice or obligation.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
110