Download SCAD Soft
Transcript
Appraisal • the shear force in the absence of oblique cracks — Sec. 4.4 of the Guide to SNiP 2.03.0184*. If the analysis is to comply with SP 52-101-03, the appraisal of sections of ferroconcrete structural members will use the following criteria: • the strength against an ultimate longitudinal force in the section — Sec. 6.2.25, 6.2.31; • the strength of concrete in tension; • the strength against an ultimate moment in the section — Sec. 6.2.25, 6.2.31; • the strength against an ultimate longitudinal force in the section — Sec. 6.2.19; • the strength against an ultimate moment in the section — Sec. 6.2.9-6.2.15; • the strains in compressed concrete — Sec. 6.2.21-6.2.31; • the strains in tensioned reinforcement — Sec. 6.2.21-6.2.31; • the height of a tensioned area of concrete — Sec. 4.1.2a, 6.2.30; • the strains in tensioned concrete — Sec. 6.2.30, 6.2.31, 7.2.11; • the longitudinal force that takes account of a deflection, with the flexibility L0/i>14 — Sec. 6.2.16; • the strength that takes into account the resistance of concrete in a tensioned area — Sec. 6.1.9, 6.1.12; • the moment accepted by the section when a crack appears — Sec. 7.2.7; • the crack opening width (short-term) — Sec. 7.2.3, 7.2.4, 7.2.12; • the crack opening width (long-term) — Sec. 7.2.3, 7.2.4, 7.2.12; • the strength against an ultimate longitudinal force in the section — Sec. 6.2.3, 6.2.8, 6.2.16, Sec. 3.50 of the Guide to SP 52-101-03 (further, the Guide to SP); • the strength against an ultimate longitudinal force in the section, that takes account of reinforcement over the height of the section — Sec. 6.2.17, Sec. 3.58 of the Guide to SP; • the strength of a concrete strip between oblique sections — Sec. 6.2.33, Sec. 3.52 of the Guide to SP; • the strength against a shear force resisted by concrete only — Sec. 6.2.34, Sec. 3.52, 3.71 of the Guide to SP; • the strength of oblique sections without transverse reinforcement — Sec. 6.2.34, Sec. 3.52,3.71 of the Guide to SP; • the strength of an oblique section — Sec. 6.2.34, Sec. 3.52,3.71 of the Guide to SP; • the shear force in the absence of oblique cracks — Sec. 4.28 of the Guide to SP; • the strength of a concrete strip between oblique sections, against Qz — Sec. 6.2.33, Sec. 3.52 of the Guide to SP; • the strength of a concrete strip between oblique sections, against Qy — Sec. 6.2.33, Sec. 3.52 of the Guide to SP; • the strength of a section under a torque — Sec. 6.2.37; • the resistance of reinforcement S1 to a torque; • the resistance of reinforcement S2 to a torque; • the resistance of side reinforcement to a torque; • the resistance of transverse reinforcement SW1 to a torque; • the resistance of transverse reinforcement SW2 to a torque. The sections of concrete structural members are appraised using the following criteria: • the strength against an ultimate longitudinal force in the section — Sec. 6.2.25, 6.2.31; • the strength of concrete in tension; • the strength against an ultimate moment in the section — Sec. 6.2.25, 6.2.31; • the strength against an ultimate longitudinal force in the section — Sec. 6.2.19; • the strength against an ultimate moment in the section — Sec. 6.2.9–6.2.15; 21