Download Multi-functional Programmable Controller CE-PTZ
Transcript
Multi-functional Programmable Controller CE-PTZ-KEY User Manual VER34<01> System Keyboard DVR MUX MENU SET/ POWER SHOT/ DVR ALM/ GRP/ AUX/ RUN/ upply * pply to ON/ PREV/ 8 NEXT/ 9 0 SYS IRIS MON 6 Tx OPEN/ BACK AUTOPAN/ 3 5 4 7 to Wal l HOLD/ 2 1 RJ45 C able OFF/ Rx MUX CLOSE/ DEL FAR/ PIC.L FOCUS NEAR/ PIC.F WIDE/ PgUp ZOOM TELE/ PgDn CAM CLR ENTER Outlet Wall O u tlet CLINTON Electronics 6701 Clinton Road Loves Park, IL 61111 1.800.447.3306 Sales 1.800.549.6393 Support 1.800.633.8712 Fax www.clintonelectronics.com Introduction Congratulations on the purchase of your new CE-PTZ-KEY. This device is a multifunctional, programmable keyboard controller for Pan-Tilt-Zoom devices, DVRs, and Matrix devices, and can be programmed with individual protocol settings for each connected device. It is equipped with a 3-Axis joystick for performing Pan, Tilt, and Zoom with a single hand. Main Features: • Manage up to 9999 devices • Controls PTZ, DVR, and Matrix in different protocol with pre-programmed settings • 3-Axis joystick • Multiplexer operation with DVR and PTZ • Password-protected for administrative access • Supports major telemetric protocols • Dual serial interface with RS232 and RS485 • Supports major DVR brands • Aluminum construction • Ergonomic Design 2 S / NEXT / NEAR.F PIC E/ TELDn Pg / ALM N MO GRP/ CAM 1 6 SE 2 HOLD 7 R ENTE Power 5 PAN/ AUTO + RS485 + DC12V + DC12V T RS232 RJ45 3 / MUX Tx FAR/.L PIC Keyboard Adaptor 5) (No: 1437 RS-232/ Power R T R RS2322 GGND GND RS23 DC12V RS485 / WIDE PgUp SYS ZOOM / NEAR.F PIC / TELE PgDn l Outle ly to Wal pp Power Su CE-PTZ-KEY Keyboard t RS-485/ DC12V RS-485/ ptor rd Ada 5) Keyboa (No: 1437 DC12V R RS2322 G RS23 DC12V RS485 Rx S Power Su R FOCU t all Outle pply to W DVR R E/ CLOSL DE ENTE CLR IRIS CAM / OPEN BACK MON 9 -PTZKE POWE NEXT Keyboard 6 RS-232/R T GND GND daptoY)r board A CE ded with RS-485/ ptor rd Ada 5) Keyboa (No: 1437 DC12V 0 ble RJ45 Ca / PREV 0 * 8 r Monito Keyboard / SHOT R RS2322 G RS23 DC12V RS485 ON/ / * 7 RJ45 U OFF/ 9 8 MEN RUN/ 4 CLR 4 MUX AUX/ 3 5 01> rd 34< boa VERm Key te Sys T/ SE/ CLO L DE 2 Power ZOOM FOCU IRIS DVR HOLD 1 + RS485 + DC12V + DC12V T RS232 Power / RUN/ r 375 AUTO / AUX/ le RJ45 Cab PAN/ PREV / WIDE PgUp / FAR .L PIC / OPEN BACK l Outlet OFF/ ALM/ SYS MUX DVR SE ON/ GRP/ Tx Rx R POWE / SHOT l Outlet MENU MUX al pply to W Power Su al pply to W Power Su DVR 1437 RS-232/R T GND tor Adap ) R DVR pto d Ada 5) RJ45 rd Keyboa RECORDE 5/ > 4<01 oard VER3 Keyb em Syst T/ R RS2322 G RS23 DC12V RS485 R RS232 G RS232 DC12V RS485 + RS485 + DC12V + DC12V T RS232 ed with -232/ T ND R daptor) oard ACEPTZKEY VIDEO DVR DIGITAL PACKAGE CONTENTS + RS485 + DC12V + DC12V T RS232 RS-232/R T GND GND Power + RS485 + DC12V + DC12V T RS232 RJ45 Keyboard RJ45 Keyboard RJ-45 Keyboard Cable RS485 Plug (2-pin) Keyboard Adaptor R RS2322 G RS23 DC12V RS485 RS-485/ ptor rd Ada 5) Keyboa (No: 1437 DC12V Power + RS485 + DC12V + DC12V T RS232 RJ45 Keyboard RS232 Plug (4-pin) GND RS-232/R T GND AU-P12H AC-DC Power Supply / SHOT AUTO / NEXT PREV / SE/ CLO L DE HOLD E/ TELDn Pg Tx > 4<01 oard VER3 Keyb em Syst T/ N 3 1 6 CLR 5 4 Power > rd R 4<01 oaDV VER3 Keyb em Syst T/ CAM 2 ptor rd Ada 5) Keyboa (No: 1437 / NEAR.F PIC MO AUX/ RS-485/ ZOOM S FOCU IRIS / RUN/ / WIDE PgUp / FAR .L PIC / OPEN BACK PAN/ ON/ ALM/ Installation and Set up SYS MUX DVR OFF/ GRP/ Rx R POWE SE MENU MUX DVR R RS2322 G RS23 DC12V RS485 User Manual Tx > 4<01 oard VER3 Keyb em Syst T/ 9 8 R ENTE DVR 7 RS-232/R T GND GND + RS485 + DC12V + DC12V T RS232 ALM/ 0 Keyboard * RS-485/ RECORDER DVR (No: 1437 RS-232/ Power R T R RS2322 GGND GND RS23 DC12V RS485 RS-485/ ptor rd Ada 5) Keyboa (No: 1437 DC12V RS-232/R T GND GND RUN/ + RS485 + DC12V + DC12V T RS232 4 RS-232/R T GND GND onitor pp Sued erud wcl Po(in VR or M BNC to D VR or BNC to D onitor VR or M Dimensions E/ Rx TELDn Pg + RS485 + DC12V + DC12V T RS232 VIDEO S 2-5/8” MUX DVR / N/ OPECK BA AUTO PRE / / RUN / AUX NEX V/ (included N MO 3EN CAM 6 5 CLR 9 R ENTE 7 0 * ble RJ45 Ca to Wall Outlet pply Power Su t all Outle pply to W Power Su t le t ut le O l al Out tol W Wal to ly ly pp ppSu wer PoSu Power l Outlet Wal Supply to Power it or Mon r Monito r Monito DVR RECORDER VIDEO DVR RECORDER VIDEO r Monito DVR DVR RECORDER M ZOO DVR SE/ CLOEL D R/ NEAC.F PI / TELE n PgD DIGITAL VIDEO RECORDER DVR N MO 3 CAM 2 1 6 CLR 5 4 8” 0 KESu wer PoTZ with CE-P DIGITAL T/ HOLD E/ TELDn Pg / NEAR.F PIC FOC IRIS G / ALM ZOOM R ENTE SE/ CLO L DE TER 0 Keyboard DVR US S FOCU IRIS NEXT 8 DIGITAL / PAN ON/ / OFF RP/ CLR daptoY)r pply to Wall Outlet board A Key E/ WIDUp Pg FAR/.L PIC / WIDE PgUp / FAR .L PIC CLR * RJ45 SYS MUX DVR T/ SHO SET U MEN Rx ER POW PREV 4 Tx 01> rd 34< boa VERm Key e yst CA 9 2 Power SYS MUX M / OPEN BACK AUTO CAM 8 Tx / 8 1 R RS2322 G RS23 DC12V RS485 6 / * onitor DVR DIGITAL 6 7 Monitor BNC to D ON/ / HOLD 9 RUN/ AUX/ Keyboard RS-485/ / SHOT N 5 7 5 RJ45 ptor rd Ada 5) Keyboa (No: 1437 VR or M RJ45 Keyboard OFF/ GRP/ ALM/ 3 R AR/ POWE NE PIC.F SE/ CLO L DE DVR 2 MO E/ TELDn Pg / NEAR.F PIC N MO PAN/ 4 2 1 + RS485 + DC12V + DC12V T RS232 SE MENU 3 MUX DVR Power Ke CE-PTZ ed withtor (includ p rd Adal TZ t leY) KE ut O Keyboawlyith -P al W to CE DC12V BNC to D R RS2322 G RS23 DC12V RS485 r Adapto Keyboard 5) DC12V VIDEO FO IRIS XT/ > NE rd 4<01 EV/ oa KePRyb VER3 LD/ HOem 1 Syst T/ GRP/ RJ45 AUX/ DVR SE/ CLO L DE ZOOM r Unpacking your keyboard Monito ble RJ45 Ca Your keyboard comes with a power supply, as well as a keyboard adaptor, and connecting r AdaptoY) eyboawrd K -PTZKE CE e firm surface. ith plugs, and cable. Carefully remove the contents from its packing and setRJon 45 Cabla (included t le ut r ble needs. Wall O Save the packing in case of future service requirements or transportation RJ45 Ca pply to Adapto Power Su KEY) yboard DC12V DIGITAL / CUS AUX/ OFF/ IRIS / WIDE PgUp HOLD ZOOM S FOCU NEXT / PREV / / WIDE PgUp N/ TOPASYS / FAR .L PIC / OPEN BACK SYS / FAR .L PIC / OPEN BACK XAU ON/ MU DVR OFF/ PAN/ AUTO N/ RU ON/ Rx R MUX DVR Tx POWE / OTP/ SHGR SE M/ AL MENU MUX MUX Rx R POWE / SHOT SE MENU 9 8 LCD Display with backlight ER ENT 7 0 * 01> rd 34< boa VER m Key te Sys T/ SE ENU 8-1/4” DVR M MUX DVR ER POW T/ SHO / PAN ON/ AUTO / OFF / GRP / ALM / RUN / AUX Operation Keys PRE / NEX V/ T/ HOLD MO 3 2 1 6 5 Extended Function Keys 4 9 8 7 0 * Digit Pad 3 Precautions For all service or installation needs, please refer to qualified service personnel or system installers Do not attempt to disassemble the device To prevent electric shock, do not remove screws or cover. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance Handle the device with care Do not strike or shake, as this may damage the device. It should be protected against extreme pressure, vibration, and humidity during transportation and storage. Damages caused by improper transportation may void the warranty. Do not operate the device beyond its specified temperature, humidity, or power source ratings. Do not use the dome camera in an extreme environment where high temperature or high humidity exists. Do not install this product in a flammable and explosive environment. Make sure that the installation is done according to your local electricity and safety regulations. Before installation or maintenance, make sure the device is disconnected from the power source. Do not use any power source other than 12vdc in order to prevent damages to this device. For details, please refer to the “Specifications” section for further details. Handle the device during the installation carefully. Falls, or extreme vibration may cause irreparable damages and void the warranty. Do not install or operate the device near any high voltage devices or high voltage cable. The safety distance should remain at least 50m. This product should be operated indoor only. 4 WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, SO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. FCC COMPLIANCE STATEMENT FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE. CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. CE COMPLIANCE STATEMENT WARNING: THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT, THIS PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES. CAUTION: BEFORE ATTEMPTING TO CONNECT OR OPERATE THIS PRODUCT, PLEASE READ THE LABEL ON THE BOTTOM AND USER’S MANUAL CAREFULLY. Technical specifications are subject to change without prior notice. Manual may contain mistakes or print errors. All trademarks mentioned belong to their respective owners. 5 Installation Safety Instructions before starting - Do not install and operate this appliance in a flammable and explosive environment. - Make sure that the installation is done according to the local electricity safety regulations of your country. - Before installation and maintenance, make sure that the appliance is disconnected from the power source. - Handle the device during installation carefully. Falls or extreme vibration may cause irreparable damages or void the warranty. - Do not install or operate the device near any high-voltage devices or high-voltage cable. The safety distance should remain at least 50m. - To achieve best image quality, its recommended to use underground cable shielded with steel tube. Do not install the cable without any protection. - In a thunderstorm area or region with high inductive voltage, such as high voltage transformer stations, it is necessary to use additional lightning-proof equipment or lightning rod for protection. - For outdoor installation, lightning-proof and grounding of the device should be considered. Please refer to the industrial safety regulations of your country. - Grounding should be considered to eliminate any interference and fulfill the safety requirements. Do not connect the ground with short-circuited or other high voltage electric networks. - Make sure that the installation environment meets the requirements of the device, such as weight support, sufficient room for cords, and power supply requirements. 6 Installation Connection Schematic The keyboard can be connected to various PTZ cameras, DVRs, and Matrix devices through the keyboard adaptor. All accessories are tested for maximum compatibility and best performance. For the first start, please ensure your keyboard parameters match those shown on the initial screen (ie. protocol, baud-rate, ID). Doing so will allow you to enter the OSD for further settings. 321 era PTZ Cam Tx > 4<01 oard VER3 Keyb em Syst T/ ) lack Wire AC24V (B ed Wire) AC24V (R DVR ection BNC Conn DVR r or to Monito MENU MUX PA AUTO S / NEXT PREV / HOLD SE/ CLO L DE R RS2322 G RS23 DC12V RS485 Adaptor rd 5) Keyboa (No: 1437 RS-232/R T GND GND + RS485 + DC12V + DC12V T RS232 CAM 2 6 CLR 4 Power 9 8 R ENTE 7 RJ45 0 Keyboard * ble EY CE-PTZK RJ45 Ca daptoY)r board A Key (included E/ TELDn Pg N 3 5 RS-485/ / NEAR.F PIC MO AUX/ 1 DC12V ZOOM FOCU IRIS / RUN/ / WIDE PgUp / FAR .L PIC / OPEN BACK N/ ON/ ALM/ SYS MUX DVR OFF/ GRP/ ire) (Green W ) RS485+ Wire (Yellow RS485- Rx R POWE / SHOT SE TZKE with CE-P l Outlet ly to Wal pp Power Su VR or M BNC to D onitor l Outlet ly to Wal pp Power Su r Monito DVR DVR DIGITAL VIDEO RECORDER RS485 CableThe telemetric control of the device uses RS485 serial communication with half duplex transmission technology. The transmission distance can vary, depending on cable type, and baud rate. The following table shows maximum distances based on cable with 0,56mm (24AWG) twisted pair: Baud Rate 2400 bps 4800 bps 9600 bps 19200 bps Max. Distance 5577ft / 1700m 3609ft / 1100m 2297ft / 700m 1312ft / 400m Due to environmental interfaces, such as electromagnetic and induction fields, or number of connected devices on the RS485 bus, or using thinner than 24AWG cable, the transmission range may be less. 7 Installation Star-ConnectionThe star-form connection is most commonly used. It enables the connection of different dome cameras with longer cable runs. It is recommended to use an RS485 distributor to ensure the telemetric data transmission. RS 485+ RS 485- Tx > 4<01 oard VER3 Keyb em Syst Rx ER SYS POW The advantage of the star-connection is that every channel can work independently and can take a cable length up to 3,280 feet (1000 meters) (depending on cable quality). In cases where more dome cameras are installed, the star-connection can be extended with additional RS485 distributors. / WIDE PgUp FAR/ PIC.L / OPEN BACK N/ ON/ OPA AUT S ZOOM FOCU IRIS OFF/ / GRP / MUX DVR T/ SHO SET/ U MEN MUX DVR NEX / ALM D/ / E/ CLOS DEL HOL RUN / T/ PREV / NEAR PIC.F / TELE PgDn MON AUX 3 2 CAM 1 6 5 CLR 4 9 8 R ENTE 7 0 * Termination ON Termination ON Termination OFF Termination OFF Tx > 4<01 oard VER3 Keyb em Syst U SYS MUX FAR/ PIC.L / OPEN BACK OPA AUT RS 485+ / WIDE PgUp DVR N/ ON/ S ZOOM FOCU IRIS OFF/ / GRP / Rx ER POW T/ SHO SET/ MEN MUX DVR NEX / ALM HOL RUN / E/ CLOS DEL PREV D/ / T/ / NEAR PIC.F / TELE PgDn RS-485 Distributor MON AUX 3 2 RS 485+ RS 485- CAM 1 6 5 CLR 4 9 8 R ENTE 7 RS 485- 0 * Tx > 4<01 oard VER3 Keyb em Syst FOCU U ER Tx Rx POW HOL MUX ZOOM OPEN BACK 3 TELE/ PgDn PIC.L / SET/ / NEAR PIC.F / WIDE PgUp MON FAR/ MEN PAN/ 2 SYS CLOSE/ DEL DVR T/ SHO MUX S IRIS NEXT / PREV D/ / WIDE PgUp FAR/ PIC.L / OPEN BACK / > 4<01 oard VER3 Keyb / em RUN / Syst AUX ALM Monitor (optional) SYS MUX DVR PAN/ AUTO ON/ OFF/ GRP/ / Rx ER POW T/ SHO SET/ U MEN MUX DVR CAM FOCUS ZOOM Up to 750m, coaxial cable Video CableVideo Amplifier (optional) Coaxial cable with 75Ω impedance with copper conductor at center conductor, and shielded with 95% copper. The following table shows different cable type and its maximum length: DVR 1 OFF/ / / 4 D/ HOL CLR NEAR PIC.F 9 RUN 8 AUX / NEXT 5 / PREV ALM / Termination ON CLR Cable Standard RG 11 / U Termination ON DVR 750 ft / 229m Balun Transmitter 1000 ft / (optional) Termination ON 0 * The values are for reference only. Depends on the cable quality and environmental conditions, the transmission Balun Receiver distance might be less. (optional) DIGITAL RG 6 / U ENTE 7 DVR (optional) Max. Distance (m / ft) RG 59 / U R Termination OFF Termination OFF ENTE CAM 9 8 Termination OFF R MON 0 6 * 5 4 Termination OFF TELE/ PgDn E/ CLOS DEL 3 7 2 1 Termination ON IRIS 6 GRP/ / AUTO ON/ 305m VIDEO RECORDER Monitor (optional) 1500 ftUp/ to 457m 1200m, twisted pair or cat5 cable If the cable length is more than 1,312ft (400m), it is recommended to use optional accessories, RS-485 Distributor such as a video amplifier or twisted-pair video converter, for boosting the video signal. RS-485 Distributor Tx > 4<01 oard VER3 Keyb em Syst 120Ω Resistor U PAN/ CAM FOCUS AUTO / 4 D/ HOL CLR NEAR PIC.F 9 RUN 8 AUX / NEXT 5 / PREV RS 485+ TELE/ PgDn 120Ω Resistor ZOOM RS 485- IRIS 6 GRP/ ALM / OPEN BACK 3 / NEAR PIC.F / WIDE PgUp PIC.L / SET/ 2 / MUX MON FAR/ MEN ON/ SYS CLOSE/ DEL DVR T/ SHO 1 OFF/ Tx Rx POW HOL MUX DVR ZOOM S FOCU IRIS ER PREV D/ / WIDE PgUp FAR/ PIC.L / OPEN BACK / NEXT / ALM / SYS MUX DVR PAN/ AUTO ON/ OFF/ GRP/ > 4<01 oard VER3 Keyb / em RUN / Syst AUX / Rx ER POW T/ SHO SET/ U MEN MUX DVR TELE/ PgDn E/ CLOS DEL R MON ENTE 3 7 2 DVR (optional) CAM 0 1 6 * 5 CLR 4 9 8 R ENTE 7 0 DVR * DIGITAL Device 1 Device 2 VIDEO RECORDER Device 3 Monitor (optional) Up to 750m, coaxial cable Extend connection distance with video amplifier Up to 750m, coaxial cable Monitor (optional) Video Amplifier (optional) Video Amplifier (optional) > 4<01 oard VER3 Keyb em Syst RS485 Connection > 4<01 oard VER3 Keyb em Syst RS485 Connection CE-PTZ-KEY CE-PTZ-KEY DVR (optional) DVR (optional) DVR DIGITAL VIDEO RECORDER DVR DIGITAL Balun Transmitter Balun Receiver (optional) (optional) Balun Transmitter Balun Receiver (optional) Up to 1200m, twisted pair or cat5 cable (optional) Extend connection distance with Twisted-Pair video converter VIDEO RECORDER Monitor (optional) Monitor (optional) Up to 1200m, twisted pair or cat5 cable > 4<01 oard VER3 Keyb em Syst RS485 Connection > 4<01 oard VER3 Keyb em Syst RS485 Connection CE-PTZ-KEY CE-PTZ-KEY DVR (optional) DVR (optional) DVR DIGITAL DIGITAL 8 VIDEO DVR VIDEO RECORDER RECORDER Tx SYS UX E/ WIDUp Pg FAR/.L PIC M ZOO US FOC RIS R/ NEAC.F PI SE/ CLOEL D / TELE n PgD Installation Key Description CLR LCD Display with backlight ER ENT 1. Camera Operation Keys Tx 01> rd 34< boa VER m Key te Sys 8-1/4” MUX DVR / / GRP PRE / 2. Operation Keys / TELE n PgD R/ NEAC.F PI SE/ CLOEL D N MO 3 CAM 2 1 3. T/ HOLD / RUN / AUX NEX V/ ZOO US FOC IRIS OFF ALM 3-Axis Joystick M / PAN AUTO ON/ / / E/ WIDUp Pg FAR/.L PIC N/ OPECK BA 5. SYS MUX DVR T/ SHO SET U MEN Rx ER POW 6 CLR 5 Extended Function Keys 4 9 8 ER ENT 7 0 * 4. Digit Pad ION ZOOM 1. Camera Operation Keys: Zoom WIDE / TELE: Zoom-in and zoom-out FOCUS FAR / NEAR: Manual focus 2-5/8” 2-5/8” 01> rd 34<eyboa IRIS OPEN / CLOSE: iris K VERm Manual te S Tx Tx SYS M US Sys ZOO / SET U MEN MUX N/ OPECK BA / PAN ON/ AUTO / / ALM PRE LD/ / RUN / AUX T NEX V/ HO MO 3 3 CAM CAM 2 6 6 5 5 CLR 4 4 / TELE n PgD R/ NEAC.F PI SE/ CLOEL D N MO N 1 1 E/ TEL E/ Dn / TEL Pg NEAR PgDn AR/PIC.F OSE/ NE .F CL E/ L PIC CLOSL DE DE XT/ NE XT/ EV/ NE PR EV/ LD/ PR HO/ HOLD 2 M ZOO FOC IRIS OFF GRP OF OFF/ RUN/ RUN/ AUX/ AUX/ US / / TELE n PgD E/ WIDUp Pg FAR/.L PIC GRP/ GRP/ ALM/ ALM/ 2. Operation Keys: DVR: Enter the DVR control mode 8”8” MUX: Multiplexer mode LEFT: WIDE RIGHT MENU: Enter setup menu or PTZ mode SET: Set preset position SHOT: Recall preset position / R/ NEAC.F PI T SHO MUX MUX DVR DVR SYS MUX DVR / DVR FOC SE/ CLOEL D ER UP E/ WIDUp Pg / .L T Rx ER POW 4. Digit Pad: 0-9: Digit input from 0 to 9 *: Star Key MON: Monitor switch CAM: Camera switch RIGHTCLR: : TELE Clear and Cancel ENTER: Enter key Tx Tx Rx R Rx SYS PORWE S MUX SY POWE X DE/ DVR MU WI /PgUp DVR / WIDE Up FAR/ SH/ OT R/ .L Pg SHOT EN/ FA .LPIC OP SE / CK PIC T/ BA OPEN SE NU CK ME BA ZOOM MENU PAN/ SZOOM TO N/ AU PA FOCU CUS ON/ AUTO IRIS FO ON/ F/ IRIS 01> rd 340<1> borad VE3R4< Kebyoa VEsRtmemKey ye ySst T/ CLR 9 9 8 8 0 0 * * LCDDisplay Display LCD withbacklight backlight with TER EN R ENTE 7 7 01> rd 340<1> borad VE3R4< Kebyoa VERtemKey Sytsem Sys SET/ N MO 3 8-1/4” 8-1/4” CLR 5 DOWN3. Extended Function Keys: ALM: Alarm function GRP: Tour function OFF: Function off ON: Function on AUTOPAN: Auto pan function AUX: Auxiliary function RUN: Function start HOLD: Hold PREV: Previous device NEXT: Next device ER ENT IRIS HO/ HOLD MO 3 3 CAM CAM 2 2 6 6 5 5 CLR 4 4 E/ TEL E/ Dn / TEL Pg NEAR PgDn AR/PIC.F OSE/ NE .F CL E/ L PIC CLOSL DE DE N MO N 1 ExtendedFunction FunctionKeys Keys Extended 3-AxisJoystick Joystick 3-Axis ZOOM OM CUSZO FO S FOCU IRIS XT/ NE XT/ EV/ NE PR EV/ LD/ PR RUN/ RUN/ 1 7 9 8 7 8 TER EN R ENTE 0 0 * * * CLR 9 7 0 DigitPad Pad Digit Joystick Functions Navigation Zoom ZOOM ZOOM NAVIGATION NAVIGATION 01> rd 340<1> borad VE3R4< Kebyoa VEsRtmemKey ye ySst S DVR DVR MENU SE MENU MUX MUX ALM/ ALM/ SH/ SHOT PAN/ TO N/ AUPA ON/ AUTO ON/ IRIS N MO N 6 5 CLR 9 7 RIGHT RIGHT CLR 9 8 R ENTE TER NE XT/ EV/ NE HO/ HOLD N MO N CAM CAM 2 1 6 5 DOWN DOWN 4 CLR 4 9 8 7 8 0 TELE TELE * CLR 9 TER EN R ENTE 7 * * 6 5 0 0 MO 3 3 1 E/ TEL E/ Dn / TEL Pg NEAR PgDn AR/PIC.F OSE/ NE .F CL E/ L PIC CLOSL DE DE XT/ LEFT:WIDE WIDE LEFT: PR EV/ LD/ PR RUN/ RUN/ AUX/ AUX/ / SH/ OT SHOT EN 7 * 9 OFF/ OFF/ GRP/ GRP/ 2 LEFT LEFT 6 5 4 8 MUX MUX ALM/ ALM/ CAM CAM 1 4 DVR DVR MENU SE MENU MO 3 3 2 2 UP UP ZOOM OM E/ TEL E/ Dn / TEL Pg NEAR PgDn AR/PIC.F OSE/ NE .F CL E/ L PIC CLOSL DE DE NE/ / NEXT HO/ HOLD FO S FOCU Tx Tx Rx R Rx SYS PORWE S MUX SY POWE X DE/ DVR MU WI /PgUp DVR WIDE Up FAR/ R/ .L Pg EN/ FA .LPIC OP / CK PIC BA OPEN CK BA ZOOM PAN/ SZOOM TO N/ AU PA FOCU CUS ON/ AUTO IRIS FO ON/ IRIS 01> rd 340<1> borad VE3R4< Kebyoa VERtemKey Sytsem Sys SET/ T/ CUSZO IRIS XT/ PREV EV/ LD/ PR RUN/ RUN/ AUX/ AUX/ Tx Tx Rx R Rx SYS PORWE S MUX SY POWE X DE/ DVR MU WI /PgUp DVR WIDE Up FAR/ R/ .L Pg EN/ FA .LPIC OP PIC / CK BA OPEN BACK OT/ SET/ T/ OFF/ OFF/ GRP/ GRP/ 1 TELE SYS DVR PAN/ TO N/ AUPA ON/ AUTO ON/ OFF/ OFF/ GRP/ GRP/ AUX/ AUX/ OperationKeys Keys Operation 9 8 DVR DVR ALM/ ALM/ 6 4 Tx Tx Rx S MUX SY X DE/ DVR MU WI /PgUp WIDE Up FAR/ R/ .L Pg EN/ FA .LPIC OP / CK PIC BA OPEN BACK PO OT/ SH/ SHOT T/ Rx 5. 3-Axis PTZ Joystick: LEFT / RIGHT: Pan movement UP / DOWN: Tilt movement TURN: Zoom in / out CAM 2 1 MENU SE MENU MUX MUX CameraOperation OperationKeys Keys Camera R POWE WER 0 RIGHT: :TELE TELE RIGHT Operation VERxx<01> System Keyboard SET MUX PROTOCOL >ROBOT VERxx<01> VERxx<01> SETThe MUX PROTOCOL SET MUX PROTOCOL Initial SetupAfter power up, the keyboard will start the initialization and self-test. LCD MON--CAM- ALMpress menu key to exit startup screen System Keyboard VERxx<01> >ROBOT System Keyboard SET MUX PROTOCOL 001 0001 >ROBOT 0001 MON display will show initial startup screen. Press MENU to start using the keyboard. SET MTX BAUD RAT VERxx<01> System SETKeyboard MUX PROTOCOL >ROBOT MON--CAMALM001 press menu key to exitMON--startupCAMscreenALMpressSystem menu Keyboard key to exit startup screen >9600bps >ROBOT VERxx<01> 001 0001 SETtoMUX PROTOCOL CAM+# SET+# S 001 0001 0001 MON--CAM-0001 ALMpress menu key exit startup screen SET MTX BAUD RAT SET MTX BAUD RAT System Keyboard >ROBOT MON--- CAM- ALM001 0001 0001 MON--ALM- screen 001 0001 0001 0 CAM 001 0001 0001 Startup Screen press menu key toCAMexit startup Main Operation Screen: >9600bps >9600bps SET MTX BAUD RAT 001 0001 0001 CAM+# 001 0001 0001 SET+#SET DVR : SHO 001 MON--SETCAMMTX ALMBAUD RAT Selected Selected Selected >9600bps press menu key to exit startup screen 001Seq 0001 0001 Ti MON--- CAM- ALM001 >SET_PROTOCOL> 0001 0001 001 001 >9600bps 0001 0001 Camera SH Alarm CAM+# Input Pos SpdSET DVR : SET+# SET RAT Monitor SETMTX DVRBAUD : 001 0001 0001 001 000 000 000 Selected Selected Selected Seq Selected Selected 001 0001 0001 MON--- CAMALM- Selected 001 0001 0001 00 >SET_PROTOCOL> >9600bps >SET_PROTOCOL> SET DVR Camera Seq Pos : Spd Ti MonitorSelected 001 Camera SET DVR : Monitor Alarm Input 001 0001 0001 Alarm Input SelectedSETSelected DVR : >SET_PROTOCOL> 001 000 >SET_BAUDRATE> Selected Selected Selected M Camera Monitor >SET_PROTOCOL> Alarm Input CAM+1 DVR_ID:01 Seq Pos 000 Spd000 Ti SET DVR : : 001 0001 0001 SET DVR Camera Monitor Alarm Input 001 000 000 SET 000DVR : DVR_ Selected Selected Selected >SET_PROTOCOL> CAM+1 use your connected PTZ camera, >SET_BAUDRATE> To quickly youCAM+1 may have to type in the corresponding camera ID >SET_BAUDRATE> SET DVR : MUX DVR_ID:01 ALL : >NVIDO Monitor Camera Alarm Input 0001camera 0001 info will show up on >SET_BAUDRATE> 001 0001 0001 CAM+1 SET DVR : 001 01 : >NVIDO screen afterCAM its connected (even if it already shows the correct ID). (ID#01 is default) Press 1 ENTER MU M DVR_ID:01 DVR_ID:01 IN:01 CAM+1 001 >SET_BAUDRATE> 0001 0001 ALL : >NVIDO camera info willtype showinup ALL : >NVIDO SET DVR : camera info will show up on theoncamera number PTZ P Cam:001 DVR_ 001 0001 0001 01 : >NVIDO CAM+1 after 01 : >NVIDO >SET_BAUDRATE> screen after its connected you wish to control: example: ALL : >NVIDO IN:01 camera info will screen show up on its connected MU DVR_ID:01 ALL : >9600bps PTZ 001info 0001 0001 type in the camera number ALLits: >NVIDO type in the camera number hit “CAM” button, then “1”, PTZ camera will show up on 01 : >NVIDO screen after connected PTZ Cam:001 01 : >9600bps M Set DVR_ID:01 younumber wish to control: 01ALL : >NVIDO you after wish towill control: thenexample: “ENTER” to control camera #1. DVR ID: IN:01 screen connected type in the camera ALL : >9600bps : >NVIDO ALL : >9600bps camera infoits show example: up on PTD 01< 00 99> PTZ Cam:001 Set hit “CAM” button, then “1”,be necessary the first hitin“CAM” button, then “1”, This may type the camera number you wish to control: example: 01 : >9600bps 0101 : >NVIDO : >9600bps screen after its connected ALLDVR : >9600bps Set Set ID: 01< SET DVR : then “ENTER” totime control camera #1.your keyboard, then “ENTER” to control camera #1. you connect you wish to control: example: hit “CAM” button, then “1”, ALL : >9600bps type in the camera number 01 00 : >9600bps >SET_CHANNEL> 01< Se This maycamera be necessary the first “CAM-0001” 01< DVR ID 99> User Mode & Admin Mode This may necessary even shows on Set DVR ID: Output to Matrix hityou “CAM” button, then “1”, the first then “ENTER” control #1. if it 01ALL :to >9600bps wish tobe control: example: SET DVR : : >9600bps SET DVR : time you connect your keyboard, time you connect your keyboard, the LCD display. 01< 00 99> then “ENTER” to control camera #1. DVR01 I This may be necessary the first ID:01 OUT:0001 hit “CAM” button, then “1”, 01 : >9600bps >SET_CHANNEL> MUX The keyboard will enter USER MODE power allows performing PTZ SET DVR Output : CAM:001 even if keyboard, it showsafter “CAM-0001” on up, which to >SET_CHANNEL> Matrix DVR ID even ifbe it shows “CAM-0001” on#1.automatically This may necessary thecamera first timeinto you connect your IN:01 ID:0 then “ENTER” to control SET DVR : LCD display. >SET_CHANNEL> the the LCD display. time you connect your keyboard, ID:0 even if it to shows “CAM-0001” on ID:01 Outputwill to Matrix DVR ID DVR IDInputOUT:0001 and DVR control, and keyboard setup menu. Following message This may be necessary the first restrict user access MonitorIN:0 IDM DVR Assign to show: ADMIN AUTHORITY >SET_CHANNEL> even if it shows “CAM-0001” on IN:0 the LCD display. SET DVR : IN:01 Channel CAM:001 Camera ID time you connect your keyboard, ID:01 OUT:0001 DVRID I 001 0001 0001 the LCDif display. >SET_CHANNEL> DVR ID DVR ID even it shows “CAM-0001” on MUX IN Monitor ID for output Chann Monitor ID for output DVR Input IN:01 CAM:001 Assign to ADMIN AUTHORITY ADMIN AUTHORITY ID:01 OUT:0001 Chan Channel Camera ID ID for output the LCD DVR ID 001 0001 PASSWORD 0001 Monitor 001 display. 0001 0001 ADMIN AUTHORITY IN:01 CAM:0001 MU DVR Input Assign to : DVR ID Ch Monitor ID for output Channel Camera ID ADMIN AUTHORITY 001 0001 0001 ID:01 OUT:0001 ID:01 OUT:0001 001 0001 : 0001 DVR ID IN:01 PASSWORD IN:01 CAM:0001 Monitor :ID for********** output CAM:0001 ID:01 OUT:0001 PASSWORD ADMIN AUTHORITY DVR CH ID Camera ID:01 : OUT:0001 IN:01 CAM:0001 Enter Mode: 001 Administrator 0001 0001 PASSWORD **********PASSWORD : ********** (mappe IN:01 CAM:0001 PASSWORD : 9876543210 ID:01 DVR CH ID DVR CH ID OUT:0001 ********** Camera ID Camera ID 1. Press ON: &: 2 at the same time PASSWORD : PASSWORD IN:01 CAM:0001 PASSWORD ********** (mapped to DVR CH ID) DVR CH ID (mapped to DVR CH ID) Camera ID 9876543210 9876543210 PASSWORD 2. Enter your password with the number with ENTER (default password: 9876543210) DVRkeys CH ID: and confirm Camera ID (mapped to DVR CH ID) ********** PASSWORD : SET CAM PROTOCOL 9876543210 (mapped to DVR CH ID) DVR CH ID Camera ID 9876543210 >SET_PROTOCOL> PASSWORD : ALL : >B02 (mappedparameters to DVR ID) as described in the SETnext CAM PROTOCOL ALL CH : >B02 Entering into Admin. mode will allow you toSET setCAM upPROTOCOL device steps. 9876543210 01 : >B02 >SET_PROTOCOL> 01 : >B02 >SET_PROTOCOL> ALL : SET >B02 SET CAM PROTOCOL CAM PROTOCOL 3. To exit Admin. mode, the device must beSETpowered down by the RJ45 connector 01 from ALL unplugging : >B02 : >B02 CAM PROTOCOL >SET_PROTOCOL> >SET_BAUDRATE> : >B02 >SET_PROTOCOL> the back of the keyboard. SET CAM PROTOCOL ALL : >9600 SET CAM PROTOCOL 01ALL ALL : >9600bps : >B02 SET CAM PROTOCOL >SET_BAUDRATE> >SET_BAUDRATE> : >9600bps 0101 : >B02 SET CAM PROTOCOL >SET_PROTOCOL> ALL : >9600bps 01 : >9600 SET CAM PROTOCOL ALL : >9600bps >SET_BAUDRATE> 01 : >9600bps >SET_BAUDRATE> SET KEY ID 01ALL: >9600bps SET CAM PROTOCOL : >9600bps Keyboard Setup: >01<00 -->63> >SET_BAUDRATE> 01 : >9600bps After entering Admin. mode, press MENU SET KEY ID SET KEY LEV SET KEY ID SET KEY LEVEL >01<00 -->1 >01<00 -->63> >01<00 -->15> >01<00 -->63> SET KEY LEVEL SET KEY ID SET MON RANGE To cycle through selections press UP or DOWN to cycle through settings. SET KEY LEVEL SET KEY ID >01<00 -->15> >01<00 -->63> >0000 -->0239 To cycle through options, turn the joystick>01<00 (tele zoom or wide zoom) to change setting. SET MON RANGE >01<00 -->15> -->63> SET CAM RA SET MON SET CAM RANGE SET KEY LEVEL SET KEY ID RANGE >0000 -->99 >0000-->63> -->0239 Apply a selection by pressing ENTER >0000-->15> -->9999 >01<00 >01<00 SET MON RANGE>0000 -->0239 SET CAM SETRANGE ALM RANGE SET MON RANGE SET CAM RANGE >0000 -->0239 >0000>0000 -->9999 -->9999 >0000 -->0239 >0000 -->9999 SET ALM RANGE RESET DEFA SET ALMRANGE RANGE RESET DEFAULT_I? RESET DEFAULT_I? SET MON SET CAM RANGE >******* -->9999 >********** >0000 -->9999 SETPLEASE ALM RANGE WAIT >0000 ... RESET DEFAULT_I? >0000 -->0239 R >0000 -->9999 SET ALM RANGE Settings RESET DEFAULT_I? >********** >0000DEFAULT_I? -->9999 RESET P >********** >0000 -->9999 PLEASE ... SET ALM RANGE RESET DEFAULT_I? RESET WAIT DEFAULT_I? >********** >0000 -->9999 PLEASE WAIT . . . SET MUX PROTOCOL: Setup the Protocol for Multiplexer. Supporting: ROBOT (default), VC, SONY, BOSCH, and PELCO. SET MUX PROTOCOL >ROBOT MON--- CAM- ALM001 0001 0001 SET MUX PROTOCOL SET+# SHOT+# MON--- CAM- ALMMTXBAUD BAUD RAT SET SET MTX RATE: Setup the BaudCAM+# Rate 0001 for Matrix. Supported: 1200bps, 4800bps, 9600bps >ROBOT 001 001 0001 0001 0012400bps, 0001 0001 001 0001 0001 0001 >9600bps (default), and 19200bps. Press ENTER to save or CLR to exit. SET DVR MTX:BAUD RAT SET >9600bps >SET_PROTOCOL> SET DVR DVR :: SET >SET_PROTOCOL> >SET_BAUDRATE> ALL DVR : >NVIDO SET : Seq Pos Spd Ti CAM+# 001 000 0000001 000 0001 SET+# 001 0001 0001 SHOT+# 001 0001 0001 DVR_ID:01 Seq Pos Spd Ti 001 000 000 000 MUX_ID:01 10 DVR_ID:01 IN:01 PTZ Cam:001 MUX_ID:01 IN:01 PTZ Cam:001 RJ45 PRE D/ / NEX V/ T/ SE/ CLO DEL HOL RUN / R/ NEA PIC.F / TELE n PgD RS485 + DC12V + DC12V + RS232 T RS232 R RS232 G DC12V RS485 - OFF / ALM DC12V ZOO RS-485/ M US FOC IRIS GRP / E/ WID p PgU FAR/ PIC.L N/ OPE K BAC OPA AUT (No: 14375) SYS MUX DVR N/ ON/ / Keyboard Adaptor Rx ER POW T/ SHO / SET U MEN MUX CRICKET ics CLINTON Electron RS-232/ GND GND R T Tx > 4<01 oard VER3 Keyb em Syst DVR Keyboard CAM+# SET+# SET MTX BAUD RAT 001 0001 0001 MON--- CAM- ALM001 0001 0001 >9600bps VERxx<01> SET MUX PROTOCOL MON--- CAM- ALM001 0001 0001 System Keyboard >ROBOT 001 0001Spd 0001 Seq Pos Ti SET MUX PROTOCOL MON--- CAM-SET ALMDVR : 001 000 000 000 >ROBOT press menu key to exit startup screen Selected Selected 001 0001 0001 Selected >SET_PROTOCOL> SET MUX PROTOCOL DVR Monitor VERxx<01> MON--- CAM- ALMCAM+# SET+# Camera Alarm Input SET >ROBOT MTX BAUD RAT System Keyboard 001 001 00010001 00010001 MON--- CAM- ALM001 0001 0001 >9600bps DVR_ID:01 CAM+# SET+# SHOT+# MTX BAUD RATto0001 SET SET DVR PROTOCOL: Setup the DVR Protocol. Supported: NVIDO, VC, DSCP, HIK, TUMIN, MITSU, DH, and 001 0001 SET DVR : press menu key exit startup screen 001 0001 0001 001 0001 0001 001 0001 0001 >9600bps CAM+1 SET+# >SET_BAUDRATE> SeqCAM+# Pos Spd Ti SET MUX PROTOCOL SET MTX BAUD RAT INTLX. MON--- CAMALMSET DVR : 001MON--0001 0001 001 0001 0001 CAMALM001 0001 0001 001 000 000 000 >ROBOT Selected Selected Selected >9600bps 001 Pos0001 0001 Seq Spd Ti >SET_PROTOCOL> DVR_ID:01 IN:01 0001 0001 Camera SET DVR : 001 Monitor Alarm ALL : >NVIDO camera info will show upProtocol on Inputsetting for all DVR ALL: ID 001 000 000 000 PTZ Cam:001 >SET_PROTOCOL> Seq Pos Spd Ti 01 SET : >NVIDO 01: individual for DVRCAM+# ID 01 screen after its connected Rxx<01> SHOT+# DVR_ID:01 SET MUXsetting PROTOCOL DVR : SET+# MON--CAMALMSETtype MTX BAUD RAT SET DVR : 001 000 000 000 Selected Selected in the camera number Selected m Keyboard 001 0001 0001 001 001 0001 >ROBOT >SET_PROTOCOL> MUX_ID:01 001 0001 0001 0001 0001 DVR_ID:01 >9600bps Set 0001 DVR ID: CAM+1 >SET_BAUDRATE> Camera Monitor wish to control: example: Alarm Input SETyou DVR : ALL : >9600bps 01<4800bps, 00 99> 001 0001RATE: 0001 SET DVR BAUD Setup the Baud Rate for DVR. Supported: 1200bps, 2400bps, 9600bps, ey to exit startup screen hit “CAM” button, then “1”, DVR_ID:01 >SET_BAUDRATE> 01 Ti: >9600bps Seq Pos Spd DVR_ID:01 IN:01 CAM+# SET+# SHOT+# SET DVR : then “ENTER” to control camera #1. SET DVR : ALL 000 : >NVIDO camera info will show up on SET MTX BAUD RAT 001 000 000 and 19200bps. Press ENTER to save or CLR to exit. PTZ Cam:001 CAM+1 0001 0001 CAM- ALM001 0001 0001Output to001 MUX_ID:01 Matrix 0001 0001 DVR IDIN:01 This may beits necessary the>9600bps first >SET_PROTOCOL> DVR_ID:01 01 >SET_BAUDRATE> IN:01 : >NVIDO 001 screen after connected ALLtime : >NVIDO 001 0001your 0001 SET DVR : 0001 0001 PTZ Cam:001 keyboard, PTZ Cam:001 type inyou theconnect camera number ID:01 OUT:0001 DVR_ID:01 IN:01 01 even : >NVIDO MUX_ID:01Set DVR ID: DVR_ID:01 >SET_CHANNEL> if it to shows “CAM-0001” on Seq Pos Spd Ti you wish control: example: : >NVIDO IN:01 CAM:001 camera info will show up on ALL ALL : >9600bps SET DVR : PTZ Cam:001 SET DVR : 01< 00 99> the“CAM” LCD display. 001 000 000 000 ALL: Protocol setting for all DVR ID Selected Selected Set MUX ID: hit button, then “1”, 01 : >NVIDO screen after its connected Set DVR ID: 01 : >9600bps DVR Input >SET_BAUDRATE> Assign to >SET_PROTOCOL> 01:number individual ID 01 ALL : >9600bps Camera 01< 00 66> then “ENTER” control camera #1.setting for DVR01< Alarm Input type in thetocamera Channel 00 99> Camera ID SetIN:01 DVR ID: to Matrix 01This : >9600bps Output MUX_ID:01 DVR ID maywish be necessary first MUX_ID:01 DVR_ID:01 IN:01: >9600bps you to control:the example: DVR ID ALL DVR_ID:01 Monitor ID for output ADMIN AUTHORITY ALL : hit >NVIDO 01< 00 99> SET DVR : PTZ Cam:001 SET time you connect yourthen keyboard, PTZ Cam:001 “CAM” button, “1”, DVR : ID:01 OUT:0001 Monitor ID for Output MUX ID Output 01 to Matrix : >9600bps DVR ID 0001 0001 01even :001 >NVIDO >SET_CHANNEL> 1 if :it “ENTER” shows “CAM-0001” on then to control>SET_BAUDRATE> camera #1. IN:01 CAM:001 SET DVR ID:01 OUT:0001 ID:01 OUT:0001 ID:01 OUT:0001 0001 0001 the LCD display. Output to Matrix DVR ID This may be necessary the first Set MUX ID: >SET_CHANNEL> Set DVR ID: MUX_ID:01 IN:01 DVR Input IN:01 CAM:001 Assign to IN:01 IN:01 CAM:0001 IN:01 CAM:001 PASSWORD : SET DVR : DVR_ID:01 time you connect your keyboard, ALL : >9600bps 01< 00 66> Channel ALL :multiple >NVIDO ID:01 Camera OUT:0001 ID DVRs used, the keyboard can map MUX theInput DVR-channel input to Cam:001 o will show up SET on DVR CHANNEL: When 01< are 00 99> PTZ PTZ Cam:001 >SET_CHANNEL> Camera ID DVR Input even if it shows “CAM-0001” on Assign to 01 : >9600bps : >NVIDO IN:01 CAM:001 DVR ID er its connected ********** Monitor ID for outputthe PTZ Channel ADMIN AUTHORITY certain PTZ IDs. Once the01DVR’s channelChannel is changed on the keyboard, corresponding to this DVR Camera ID the LCD display. e camera number Monitor ID for OutputAssign to DVR CH ID MUX ID Camera ID DVR Input Output to Matrix 001 0001 0001 DVR ID Set MUX ID: DVR ID Set DVR ID: PASSWORD : Monitor ID for output will beSETselected automatically. o control: example: Channel Camera ID DVR : (mapped to DVR CH ID) ID:01 ALL : >9600bps OUT:0001 01< 00 66> ID:01 OUT:0001 ID:01 OUT:0001 01< 00 99> 9876543210 button, then “1”, DVR ID >SET_CHANNEL> Monitor ID for output 01 : >9600bps ADMIN AUTHORITY IN:01 CAM:001 IN:01 CAM:0001 IN:01 CAM:001 PASSWORD : ER” to control camera #1. ID:01 001 OUT:0001 0001 0001 Monitor ID for Output MUX ID Camera ID Output to Matrix MUX Input DVR Input DVR ID Assign to e necessary the first IN:01 ********** CAM:0001 Channel ID:01 OUT:0001 ALL : >B02 Channel SET CAM PROTOCOL Camera ID SET DVR : onnect your keyboard, ID:01 OUT:0001 ID:01 ID OUT:0001 DVR CH IN:01 ID Camera CAM:0001 01 : >B02 >SET_PROTOCOL> DVR PASSWORD >SET_CHANNEL> PASSWORD : : ID for output Monitor hows “CAM-0001” on ID IN:01 CAM:001 IN:01 CAM:001 (mapped to DVR CH ID) DVR CH ID9876543210 Camera ID splay. ********** MUX Input Camera ID DVR Input Assign to (mapped to DVR CH ID) SETCH CAM ALL : >9600bps Channel Channel ID:01 OUT:0001 Camera ID DVR ID PROTOCOL Camera ID >SET_BAUDRATE> 01 : >9600bps IN:01 PASSWORD CAM:0001: DVR ID (mapped to :DVR CH ID) Monitor ID for output SET CAM PROTOCOL AUTHORITY ALL >B02 9876543210 0001 0001 Example: 01 : >B02 >SET_PROTOCOL> ALL : >B02 SET CAM PROTOCOL ID:01 OUT:0001 DVR >SET_PROTOCOL> CHmode: ID : >B02 In DVR If Camera DVR2IDis01selected in the schematic below, and PTZ input: is changed to 2, the keyboard CAM:0001 >B02 PROTOCOL ALL SETALL LEVEL SETSET KEYCAM ID ORD : SET CAM PROTOCOL :KEY >9600bps (mapped to IN:01 DVR CH ID) will automatically recognize the 2nd camera on >SET_BAUDRATE> the selected (in example PTZ ID#6 would be 01 : -->15> >B02 >SET_PROTOCOL> >01<00 >01<00 -->63> DVR 01 : this >9600bps ****** SET CAM PROTOCOL ALL : >9600bps selected as it is the 2nd PTZ camera in sequence on this paticular DVR). DVR ID >SET_BAUDRATE> 01CH: >9600bps Camera ID ORD : CAM PROTOCOL SETALL : >9600bps SETSET MON RANGE CAM RANGE ALL : >B02 SET CAM PROTOCOL (mapped to DVR CH ID) 43210 >SET_BAUDRATE> 01 -->9999 : >9600bps >0000 -->0239 >0000 01 : >B02 >SET_PROTOCOL> SET KEY LEVEL SET KEY ID RS 485 >01<00 -->15> >01<00 -->63> SET ALM RANGE RESET DEFAULT_I? RESET DEFAULT_I? SET KEY LEVEL SET SETKEY CAMIDPROTOCOL ALL ALL : >B02>0000 SET: >9600bps CAM PROTOCOL BNC to DVR >********** -->9999 PLEASE WAIT . . . >01<00 -->15> >01<00 -->63> >SET_BAUDRATE> 01>SET_PROTOCOL> : >9600bps 01 : >B02 KEY LEVEL KEY ID SETSET MON RANGE SETSET CAM RANGE >01<00 -->15> >01<00 -->63> >0000 -->0239 >0000 -->9999 Communication Cable SET MONRJ45 RANGE SET CAM RANGE SET CAM PROTOCOL ALL : >9600bps >0000 -->0239 >0000 -->9999 >SET_BAUDRATE> 01 : >9600bps MON RANGE SETDEFAULT_I? CAM RANGE SETSET ALM RANGE RESET RESET DEFAULT_I? SET KEY LEVEL SET KEY ID >0000 -->0239 >0000 -->9999 >********** >0000 -->9999 PLEASE WAIT . . . >01<00 -->15> >01<00 -->63> SET ALM RANGE RESET DEFAULT_I? RESET DEFAULT_I? RS 485 >********** >0000 -->9999 PLEASE WAIT . . . #1 #1 #2 Z ID#4 PTZ ID#3 DVR ID PTZ ID SET ALM RANGE PTZ ID RESET DEFAULT_I? RESET DEFAULT_I?PT SET MON RANGE SET CAM RANGE tor ap SET KEY LEVEL SET KEY ID Ad rd >********** >0000 -->9999 EY ) PLEASE WAIT . . . Keyboa CE-PTZK >0000 -->0239 ded with -->9999 >0000 (inclu >01<00 -->15> >01<00 -->63> RS 485 N MO AUX 3 2 CAM 1 6 5 CLR 4 9 8 ER ENT 7 0 * SET ALM RANGE >0000 -->9999 Y CE-PTZKE RESET DEFAULT_I? SET MON RANGE >********** >0000 -->0239 BNC to DVR RESET DEFAULT_I? SET CAM RANGE PLEASE WAIT . . >0000 -->9999. SET ALM RANGE >0000 -->9999 RESET DEFAULT_I? >********** RESET DEFAULT_I? PLEASE WAIT . . . CRICKET ics CLINTON Electron PTZ ID#5 DVR ID#2 11 PTZ ID#6 PTZ ID#7 PTZ ID#8 PTZ C Channel VERxx<01> MUX PROTOCOL IN:01 CAM:0001 Monitor PASSWORD : MON--- CAMInputSET 01 : >NVIDO screen after its connected This may beCamera necessary Alarm the first DVR>ROBOT ID System Keyboard Monitor ID for output ADMIN AUTHORITY SET DVR : 001 0001 type in the camera number time you connect your keyboard, ********** Set DVR ID: 001 0001 0001 SET DVR : >SET_CHANNEL> wishkey to control: example: even if it shows “CAM-0001” on pressyou menu to exit startup screen ALL >9600bps Camera ID DVR CH:ID 01< 00 99> >SET_BAUDRATE> ID:01 OUT:0001 hit “CAM” button, LCD display. PASSWORD : then “1”, the CAM+1 CAM+# 01 MTX : >9600bps SET BAUD RAT (mapped to DVR CH ID) 001 0001 0001 IN:01 CAM:0001 then “ENTER” to:control 9876543210 PASSWORD 001 0001 MON--CAMALM- camera #1. >9600bps CAM Ou DVR ID This may be necessary first VERxx<01> 001 0001 0001 thecamera ALLMUX : >NVIDO SET PROTOCOL info will show up on DVR ID Monitor ID for output ********** ADMIN AUTHORITY SET DVR : System Keyboard time you connect your keyboard, 01 : >NVIDO >ROBOT screen after its connected ID:01 OU Seq Pos Sp SET CAM PROTOCOL: Setup the Protocol for CAM. Each camera CH IDCAM 001 0001 0001 can DVR >SET_CHANNEL> Camera ID ALL : >B02 SET DVR : PROTOCOL even if it shows “CAM-0001” on SET type in the camera number IN:01000 00 CA PASSWORD : 001 Selected Selected Selected press menu keypress to exit startup screen >SET_PROTOCOL> (mappedID:01 to01 DVR: >B02 CH ID) OUT:0001 theprotocol. LCD display. After be programmed with a different setting, >SET_PROTOCOL> you wish to control: ENTER example: 9876543210 Camera Monitor DVR Input ALL : >9600bps Alarm Input IN:01 CAM:0001 SET MTX BAUD RAT : then “1”, hitPASSWORD “CAM” button, Channel 01 : >9600bps to save, or CLR to exit the setting. MON--- CAM- ALMDVR_ID:01 ALL:SET Protocol setting for all>9600bps CAMERA ID then********** “ENTER” to control camera #1. DVR ID CAM PROTOCOL ALL : >9600bps SET DVR : Monitor ID for output 001 0001 0001 ADMIN AUTHORITY 01: SET individual setting for CAMERA 01 ALL :ID :>9600bps >B02 CAM PROTOCOL CAM+1 0001 0001 This may be necessary the first >SET_BAUDRATE> >SET_BAUDRATE> 01 DVR SET CH ID 001 Camera ID DVR : time you connect your keyboard, PASSWORD : >SET_PROTOCOL> 001 0001 0001 SET01 DVR: :>B02 (mapped to DVR CH I ID:01 OUT:0001 Selected Selected >SET_CHANNEL> Selected DVR_ID:01 even9876543210 if it shows “CAM-0001” on >SET_PROTOCOL> : >NVIDO camera info will: show up on IN:01 CAM:0001 Camera Monitor PASSWORD Alarm Input ALL PTZ C the LCD display. SET CAM PROTOCOL ALL : >9600bps 01 : >NVIDO SET CAM BAUDRATE: Setup the Baud Rate for CAM. Supported screen after its connected SET KEY LEVEL SET KEY ID >SET_BAUDRATE> 01 : :>9600bps type ********** in the camera number SET DVR ALL >B02 SET CAM PROTOCOL settings: 1200bps, 2400bps, 4800bps, 9600bps, and 19200bps. After DVR CH>01<00 >01<00 -->15> -->63> Setoutput DVR: ID: DVR ID ID Monitor ID for Camera ID CAM+1 youPASSWORD wish to control: example: ADMIN AUTHORITY >SET_BAUDRATE> ALL: Protocol setting for all CAMERA ID ALL : >9600bps : 0100 : >B02 >SET_PROTOCOL> 01< 99> (mapped to DVR CH ID) setting, press ENTER to save orhit CLR tobutton, exit the setting. 001 0001 “CAM” then “1”, 001 0001 0001 0001 01: individual setting for CAMERA ID 01 01 : >9600bps 9876543210 SET MON RANGE SET CAM RANGE then “ENTER” to control camera #1. ID:01: >NVIDO OUT:0001 ALL camera info will show up on SET CAM PROTOCOL SET KEY-->9999 LEVEL SET KEY-->0239 ID >0000 >0000 Out DVRALL ID : >960 This may be necessary the first IN:01 CAM:0001 PASSWORD : 01 : >NVIDO screen after its connected >SET_BAUDRATE> 01 : >960 >01<00 -->15> SET>01<00 DVR : -->63> time you connect your keyboard, ID:01 OU ALL : >B02 SET CAM PROTOCOL type in the camera number >SET_CHANNEL> even if it shows “CAM-0001” on********** SET ALM RANGE DEFAULT_I? IN:01RESETCA D <01> SET MUX PROTOCOL 01RESET : >B02 SET Keyboard MUX PROTOCOL >SET_PROTOCOL> you wish to MON--control:CAMexample: ALMMON--CAMALM>9600bps the LCD display. >:ID CHSET >0000 -->9999 SET MON RANGE DVRALL CAM RANGE Camera DVR ID Input PLEASE W yboard >ROBOT >ROBOT ********** hit “CAM” button, then “1”, 001 0001 0001 PASSWORD : A 001 0001 0001 01 >0000 : >9600bps >0000 -->0239 -->9999 (mappedChannel to DVR CH IC thento “ENTER” to control camera #1. SET by 9876543210 CAMusing PROTOCOL SET KEY ID: Setup the ID of the controller from 01 63. Input the number SET KEY LE ALL : >9600bps SET KEY ID o exit startup screen DVR ID This may beCAM+# necessary the first ADMIN AUTHORITY >01<00 -01 : >9600bps >01<00 -->63> SET+# Monitor ID for output SHOT+# CAM+# SET+# SHOT+# SET MTX BAUD RAT theBAUD digit press ENTER to0001 savetime or CLR to exit the setting.>SET_BAUDRATE> SET MTX RATkeys. After setting, SET ALM RANGE SETRESET DVR : DEFAULT_I? RESET D you0001 connect your keyboard, 001 00010001 001 0001 0001 M- ALM001 0001 0001 001 0001 0001 001 0001 001 0001 001 0001 0001-->9999 >9600bps > >9600bps >0000 >SET_CHANNEL> PLEASE W even if it shows “CAM-0001” on ALL : >B02 SET CAM PROTOCOL ********** 01 0001 ID:01 OUT:0001 SET MON RANGE SET CAM R the LCD display. 01 : >B02 >SET_PROTOCOL> IN:01 CAM:0001 Seq Pos Spd Ti PASSWORD >0000 -->0239 >0000 --> Seq Pos Spd: Ti SET levels of the controller from 0 to 15. Input the SETthe DVRcontrol : SET DVR : KEY LEVEL: Setup SET KEY LEVEL SET KEY ID 001 000 000 000 ected Selected 001 000 000 000 >SET_PROTOCOL> ********** >SET_PROTOCOL> >01<00 -->15> >01<00 -->63> ALL : >960 Monitor ID for output by using the digit keys. After setting, press ENTER to save orDVR CLR to exit the DVR ID SET mera ADMIN AUTHORITY Alarmnumber Input SETCAM ALMPROTOCOL RANGE RESET DE CH ID Camera ID >SET_BAUDRATE> 01 : >960 MUX_ID:01 PASSWORD : 001 0001 0001 > >0000 -->9999 MUX_ID:01 DVR_ID:01 DVR_ID:01 setting. ****** (mapped to SET DVR CH ID) SET MON RANGE RANGE SET DVR : 9876543210 SET DVR : ID:01 CAM OUT:0001 >0000 -->0239 >0000 -->9999 >SET_BAUDRATE> >SET_BAUDRATE> IN:01 CAM:0001 PASSWORD : 01 0001 MUX_ID:01 IN:01 SET KEY LE MUX_ID:01 IN:01 DVR_ID:01 IN:01 SET KEY ID DVR_ID:01 IN:01 ********** ALL : >B02 SETCAM ALMPROTOCOL RANGE RESET SET RESET DE ALL : >NVIDO ill show up on ALL : >NVIDO PTZ DEFAULT_I? Cam:001 >01<00 PTZ Cam:001 PTZ Cam:001 Monitor ->01<00 -->63>Camera PTZ Cam:001 DVR CH ID 01 : >B02 > >0000 -->9999 >SET_PROTOCOL> ID PLEASE W 01 : >NVIDO s connected 01 : >NVIDO ********** PASSWORD : (mapped to DVR CH ID mera number SET MON RANGE: Setup the range of monitors from 0000 to 0239.SetInput the 9876543210 Set MUXRANGE ID: MUX ID: Set DVR ID: SET MON Set DVR ID: SET CAM R ontrol: example: SET CAM PROTOCOL ALL : >9600bps ALL : >9600bps 01< 00 66> ALL : >9600bps 01<CLR 00 66> keys.01< After setting, press ENTER to exit the 01<to 00 save 99> or >0000 -->0239 00 99> >0000 --> on, then “1”, number by using the digit >SET_BAUDRATE> 01 : >9600bps 01 : >9600bps VERxx<01> 01 : >9600bps SET MUX PROTOCOL MONo control camera #1. setting. ALL : >B02 SET CAM PROTOCOL System Keyboard >ROBOT Monitor ID for Output MUX ID RANGE Monitor ID for Output ID OutputMUX to Matrix SET ALM RESET DE DVR ID ecessary the first Output to Matrix DVR ID 01 :001 >B02 >SET_PROTOCOL> SET DVR : SET DVR : >****** >0000 nect your keyboard, ID:01-->9999 OUT:0001 ID:01 OUT:0001 press menu key to exit startup screen ID:01 OUT:0001 ID:01 OUT:0001 >SET_CHANNEL> >SET_CHANNEL> ws “CAM-0001” on CAM+ SETIN:01 KEY LEVELCAM:001 KEY IN:01 SET CAM:001 IN:01 CAM:001 IN:01 CAM:001 SETIDMTX BAUD RATSET CAM PROTOCOL ALL : >960 Camera range y. 001 >01<00 -->15> Camera ID >01<00 -->63> MON--- CAM- ALMMUX Input >9600bps MUX Input Camera ID >SET_BAUDRATE> DVR Input 01 : >960 Assign to DVR Input Assign to 001 0001 0001 Channel Channel Channel Camera ID0000 to 9999. Channel of intelligent Camera ID SET CAM RANGE: Setup the range dome cameras from Seq DVR ID SET MON RANGE SET CAM RANGE DVR ID Monitor ID for output Monitor ID for output HORITY SET CLR DVR : Input the number by using the digitSelected keys. After setting, press ENTER to save 001 >0000or -->0239 Selected >0000 -->9999 Selected 01 0001 >SET_PROTOCOL> Monitor Camera Alarm Input SET KEY LE SET KEY ID to exit the setting. ID:01 OUT:0001 ID:01 OUT:0001 >01<00 --> SET ALM RANGE >01<00 -->63> RESET DEFAULT_I? DVR_ID RESET DEF IN:01 CAM:0001 IN:01 CAM:0001 : SET DVR : >********** >0000 -->9999 PLEASE WA CAM+1 >SET_BAUDRATE> **** SET MON RANGE SET CAM R 001 0001 0001 DVR CH ID Range DVR CH Alarm ID Camera ID >0000 -->0239 Camera ID >0000 -->9 DVR_I : ALL : >NVIDO camera (mapped to info DVRwill CH show ID) up on (mapped to DVR CH ID) PTZ 10 01 :the >NVIDO after itspositions connected from 0000 to 9999. Input SET ALM RANGE: Setup the range screen of alarm SET ALM RANGE RESET DEF type in the camera number >****** >0000 -->9999 Set D number by using the digit keys. After setting, press ENTER to save or CLR to exit the you wish to :control: example: ALL : >9600bps ALL >B02 SET CAM PROTOCOL ALL : >B02 SET CAM PROTOCOL 01< 0 hit “CAM” setting. 01 : >9600bps 01 button, : >B02then “1”, 01 : >B02 >SET_PROTOCOL> >SET_PROTOCOL> then “ENTER” to control camera #1. DVR ID This may be necessary the first SET CAM PROTOCOL ALL : >9600bps SET DVR : SET CAM PROTOCOL ALL : >9600bps time you connect your keyboard, ID:01 >SET_BAUDRATE> even if 01 : >9600bps >SET_CHANNEL> >SET_BAUDRATE> it shows “CAM-0001” on IN:01 Reset Default 01 : >9600bps the LCD display. RESET DEFAULT_I?: Reset the keyboard to factory defaults by entering the password (default password: DVR ID ID for output AUTHORITY SETreset KEY LEVEL SET KEY SET KEYENTER LEVEL SET KEY ID 9876543210). Press toIDactivateADMIN the or CLR to exit. *NOTE: Pressing ENTERMonitor will clear all 001 0001 0001 >01<00 -->15> >01<00 -->63> >01<00 -->15> >01<00 -->63> settings that have been saved on the device. . This process can take up to 30ID:01 seconds until the controller OUT:0001 IN:01 CAM:0001 is available again. Note that if the baud-rate has been changed due to the reset, it is necessary to restart PASSWORD : SET MON RANGE SET CAM RANGE SET MON RANGE SET CAM RANGE >0000 the -->0239 >0000 -->9999 >0000 -->0239 >0000 -->9999 the keyboard by removing RJ45 cable from the back of the unit. ********** SET ALM RANGE >0000 -->9999 PASSWORD : SET ALM RANGE RESET DEFAULT_I? RESET DEFAULT_I? RESET DEFAULT_I? 9876543210 >********** >0000 -->9999PLEASE WAIT >********** ... 12 RESET DEFAULT_I? PLEASE WAIT . . . DVR CH ID Camera ID (mapped to DVR CH ID) SET CAM PROTOCOL >SET_PROTOCOL> ALL : >B02 01 : >B02 SET CAM PROTOCOL ALL : >9600bps DVR Inp Channe Working with PTZ Start PTZ mode By default, the keyboard usually starts in PTZ mode (display shown below). You can also access the PTZ menu by pressing the MENU button. SET MUX PROTOCOL >ROBOT MON--- CAM- ALM001 0001 0001 SET MTX BAUD RAT Select / Change >9600bps CAM+# SET+# SHOT+# current camera-001 0001 0001 001 0001 0001 001 0001 0001 By default, the keyboard usually starts in PTZ mode (display shown below). You can also access the SET MUX PROTOCOL SeqALMPos Spd Ti MON--- CAMDVR :menu by pressing the MENU button. >ROBOT SETPTZ 0010001 000 000 000 001 0001 >SET_PROTOCOL> SET MTX BAUD RAT: SET DVR >9600bps >SET_BAUDRATE> Preset Function- SET DVR : ALL : >NVIDO Preset: >SET_PROTOCOL> 01Add : >NVIDO CAM+# DVR_ID:01 001 0001 0001 Seq Pos Spd Ti DVR_ID:01 MUX_ID:01 0001 SET+# SHOT+# Change selected 001 0001 0001 camera 001 0001 MUX_ID:01 IN:01 PTZ Cam:001 IN:01 000 Cam:001 PTZ SET001+ 000# 000 + ENTER . #=1 to 255* SHOT + #Set + ENTER . #=1 to 255* DVR_ID:01 DVR ID: CLR + # 01< + ENTER 00 99> . #=1 to 255* Call a Preset: MUX_ID:01 Set MUX ID: SET DVR : ALL : >9600bps 01< 00 66> Delete a Preset: >SET_BAUDRATE> 01 : >9600bps MON--- CAM- ALMMON--- CAM- ALMMUX_ID:01 MUX IDIN:01Monitor ID for Output IN:01 Matrix ID maximum numberDVR_ID:01 dependsDVRon theOutput PTZ todevice. Please refer to the user’s manual for further information. 001 *The 0001 0001 001 preset 0001 0001 ALL : >NVIDO PTZ Cam:001 OUT:0001 SET DVR : PTZ Cam:001 OUT:0001 ID:01 ID:01 01 : >NVIDO >SET_CHANNEL> IN:01 CAM:001 IN:01 CAM:001 CAM+# CAM+# SET+# SET+# SHOT+# SHOT+# Set MUX ID:MUX Input Set DVR ID: Camera ID DVR Input 001 0001 0001 to 001 0001 0001 0001 001 0001 Assign 0001 001 0001 001 0001 0001 001 0001 0001 ALL : >9600bps 01< 00 66> Channel 01< 00 99> Channel Camera ID 01 : >9600bps DVR ID for Spd output Seq Pos SpdMonitor TiSeq ID Pos Ti Monitor ID for Output MUX ID Output to Matrix DVR ID - Sequence: 001 Tour 000 000 000 001 000 000 000 SET DVR : ID:01 OUT:0001 ID:01 OUT:0001 ID:01 OUT:0001 can store up to 24 preset points with individual dwell times A sequence and speeds. You can store >SET_CHANNEL> IN:01 CAM:001 IN:01 CAM:001 IN:01 CAM:0001 MUX_ID:01 MUX_ID:01 DVR_ID:01 DVR_ID:01 sequence by using this function. (Only available in B01 / B02MUX Protocol). Input Camera ID DVR Input Assign to Channel Camera ID a Channel DVR CH ID Camera ID Monitor ID for output MUX_ID:01 IN:01 Press + ID)# + SETMUX_ID:01 . #=1 to 4 IN:01 DVR_ID:01 IN:01 DVR_ID:01 IN:01 (mappedGRP to DVR CH PTZ Cam:001 PTZ Cam:001 PTZ Cam:001 Cam:001 SET MUX PROTOCOL PTZ MON--- CAM- ALMID:01 OUT:0001 >ROBOT 001 0001 0001 IN:01 CAM:0001 After entering sequence programming theID: display shows the preset input and settings for Set MUX ID:mode, Set MUX SetSET DVR ID: PROTOCOL Set DVR ID: ALL : >B02 CAM 01< 00 66> 01< 00 66> 01<>SET_PROTOCOL> 00speed 99> and 01< 00 99> time. 01 : >B02 CAM+# SET+# SHOT+# SET MTX BAUD RAT 001 0001 0001 DVR CH >9600bps ID 001 Seq: 0001 Sequence 0001 001number 0001 0001 Camera ID Monitor IDMUX for Output MUX ID Monitor ID for Output ID Output totoMatrix DVRSET ID (mapped Output to Matrix DVR CH ID) DVR ID CAM PROTOCOL ALL : >9600bps Pos: Preset number ID:01 Spd TiOUT:0001 ID:01 OUT:0001 ID:01 OUT:0001 >SET_BAUDRATE> 01 : >9600bps Seq Pos ID:01 OUT:0001 SET DVR : IN:01 CAM:001 001 000 000 000 IN:01 CAM:001 Spd: Move speed between 1-8 IN:01 CAM:001 IN:01 CAM:001 >SET_PROTOCOL> MUX Input Camera ID ALL : >B02 MUX Input Camera SET CAMDVR PROTOCOL Input Assign to DVR Input Ti: Stop IDtime between 0-60 sec. Termination ON Assign to Termination OFF Channel Channel Channel MUX_ID:01 CameraChannel ID : >B02 Camera ID 01 DVR_ID:01 >SET_PROTOCOL> Press ENTER to confirm and save the setting. SET DVR : SET KEY LEVEL SET KEY ID ID for output >SET_BAUDRATE> >01<00 -->15> >01<00 -->63> SET CAM PROTOCOL ALL : >9600bps IN:01 >SET_BAUDRATE> 01 : >9600bps DVR_ID:01 the preset position input withIN:01 speed and time settings,MUX_ID:01 and confirm with ENTER. After exiting SETRepeat MON RANGE ALL : >NVIDO CAM RANGEPTZ SETSET MUX PROTOCOL Cam:001 MON--- CAM- ALM- PTZ Cam:001 >0000 -->0239 01 : >NVIDO >0000 -->9999 >ROBOT the programming mode, the settings will be saved the 0001 dome’s memory. 001 to0001 Set MUX ID: Set DVR ID: artup screen SET ALM RANGE RESET DEFAULT_I? SET KEY LEVEL SETALL KEY :ID RESET DEFAULT_I? CAM+# era ID >9600bps 01< 00 66> Working with DVR SET+# SHOT+# 01< 00 99> SET MTX BAUD RAT >********** >0000 -->9999>01<00 -->15> D) LED DVR0001 mode -->63> PLEASE WAIT . . . pped>01<00 to DVR ID) 01 :CH >9600bps 001 0001 0001 M001 0001 0001 001 for0001 >9600bps Enter DVR mode 1 Monitor ID for Output MUX ID Output to Matrix DVR ID SETSET MON RANGE SETDVR, CAM RANGE Seq DVR-mode. Pos Spd Ti DVR : To control press the DVR-Button and enter the ID:01 Press OUT:0001 ID:01 OUT:0001 SET DVR : DVR button to >0000 >0000 -->9999 ALL :-->0239 >B02 001 000 000 000 IN:01 LSelected >SET_CHANNEL> CAM:001 IN:01 the CAM:001 >SET_PROTOCOL> The LED with “DVR” tag indicates current status, and the LCD : >B02 enter DVR mode Alarm01 Input MUX Input Camera ID DVR Input to SET ALM RANGE RESET DEFAULT_I? shows the current selectedRESET DVRDEFAULT_I? ID: Assign MUX_ID:01 DVR_ID:01 Channel Channel Camera ID > -->9999 PLEASE WAIT . . . SET DVR : 0bps L DVR>0000 ALL : >9600bps ********** ID Monitor ID for output >SET_BAUDRATE> 0bps 01 : >9600bps 1 MUX_ID:01 IN:01 DVR_ID:01 IN:01 Up to 750m, coaxial cable OUT:0001 ALL than : >NVIDO up on ID:01 PTZ pressing Cam:001 If you have more one DVR installed and configured, you can switch to other ID by NEXT PTZ Cam:001 IN:01 CAM:0001 01 : >NVIDO cted + # + ENTER. For returning to PTZ mode, press MENU. VEL SET KEY LEVEL umber Set MUX ID: Set DVR ID: 15> >01<00 -->15> xample: ALL : >9600bps DVR CH ID 01< 00 66> Camera ID 01< 00 99> n “1”, >9600bps (mapped toon DVR01 CH: ID) Depending the DVR Model, the function keys may be different. Please refer to “Function key for ol camera ANGE SET#1. CAM RANGE Monitor ID for Output MUX ID Output to Matrix DVR ID y the first 9999 >0000 -->9999 NVIDO DVR” section for key assignment. SET DVR : ur keyboard, ID:01 OUT:0001 13 ID:01 OUT:0001 ALL >SET_CHANNEL> : >B02 -0001” on IN:01 CAM:001 SET CAM PROTOCOL IN:01 CAM:001 AULT_I? RESET DEFAULT_I?RESET RESET DEFAULT_I? DEFAULT_I? Balun Transmitter R ID Term Tx > 4<01 oard VER3 Keyb em Syst U SYS MUX / WIDE PgUp DVR FAR/ PIC.L / OPEN BACK N/ ON/ OPA AUT S ZOOM FOCU IRIS OFF/ / GRP / Rx ER POW T/ SHO SET/ MEN MUX DVR NEX / ALM D/ / E/ CLOS DEL HOL RUN / T/ PREV MON AUX 3 2 / NEAR PIC.F / TELE PgDn RS-485 Distribu CAM 1 6 5 CLR 4 9 8 R ENTE 7 0 * Video Amplifi ET MUX PROTOCOL Working ROBOT with DVR MON--- CAM- ALM001 0001 0001 Virtual PTZ control in DVR mode CAM+# SET+# SHOT+# this mode, you can001 control simultaneously: by selecting the input on the DVR, 0001the 0001DVR and 001 PTZ 0001 0001 001 0001 0001 the PTZ ID assigned to this channel will be automatically selected and ready tor PTZ control (DVR and Seq Pos Spd Ti PTZ ID assignment need to be set up prior to operation. Please refer to the former chapter “Keyboard ET DVR : 001 000 000 000 SET_PROTOCOL> Setup” for details.) ET MTX BAUD RAT In 9600bps ET DVR : SET_BAUDRATE> Press PROTOCOL PROTOCOL MUX_ID:01 DVR_ID:01 DVR key (in DVR mode) to enter virtual PTZ MON--- CAM- ALMMON--- CAM- ALMDVR_ID: 01:.........ID of the DVRIN:01 MUX_ID:01 001 0001 0001 DVR_ID:01 IN:01 001 0001 0001 ALL : >NVIDO PTZ Cam:001 IN: 01.....................Input of the DVR PTZ Cam:001 1 : >NVIDO CAM+# SET+# SHOT+# PTZ.........................Indicates the virtual PTZ mode AUD RAT CAM+# SET+# SHOT+# BAUD RAT Set MUX ID:or PTZ ID 001 0001 0001 001 0001 0001 001 0001 0001 Set DVR ID: Cam:0001..............Camera 001 0001 0001 001 0001 0001 001 0001 0001 ALL : >9600bps 01< 00 66> 01< 00 99> 1 : >9600bps Seq Pos Spd Ti Switch the camera channel: Press #* + ENTER Seq input Pos Spd Ti Monitor ID for Output 001 000DVR 000 MUX ID Output to Matrix ID 000 001 000 000 000 TOCOL> For returning to the DVR mode, press the DVR key again.ID:01 OUT:0001 OTOCOL> SET DVR : ID:01 OUT:0001 >SET_CHANNEL> MUX_ID:01 IN:01 CAM:001 DVR_ID:01IN:01 CAM:001 MUX_ID:01 DVR_ID:01 DRATE> UDRATE> VIDO VIDO IDO VIDO D:01 N:01 00bps 00bps 00bps 00bps CH ID MUX Input Camera ID DVR Input Assign to Change the PTZ assignment in DVR mode Channel Channel Camera ID If you alreadyDVR_ID:01 in Admin-mode, you can change the assignment MUX_ID:01 IN:01 of the PTZ ID to the DVR input Monitor ID for are output IN:01 MUX_ID:01 IN:01 DVR_ID:01 IN:01 PTZ Cam:001 PTZ the NEXT Cam:001 key. PTZ Cam:001 directly by pressing PTZ Cam:001 OUT:0001 CAM:0001 Camera ID (mapped to DVR CH ID) DVR ID DVR ID ID:01 ID:01 IN:01 IN:01 ANNEL> ANNEL> ALL : >B02 SET CAM PROTOCOL 01 : >B02 >SET_PROTOCOL> Monitor ID for output Monitor ID for output SET CAM PROTOCOL OUT:0001 >SET_BAUDRATE> OUT:0001 CAM:0001 CAM:0001 Set MUX ID: Set DVR ID: Set DVR ID: 01< 00 99> 01< 00 99> DVR Input DVR Input Channel Channel ALL : >9600bps 01 : >9600bps SET MON RANGE SET CAM RANGE ALL : >B02 PROTOCOL -->0239 ALL : >B02 >0000 -->9999 M>0000 PROTOCOL 01 : >B02 OTOCOL> 01 : >B02 ROTOCOL> SET ALM RANGE RESET DEFAULT_I? M >0000 PROTOCOL : >9600bps >********** -->9999 ALL M PROTOCOL ALL : >9600bps AUDRATE> 01 : >9600bps AUDRATE> 01 : >9600bps SET KEY LEVEL SET KEY LEVEL >01<00 -->15> >01<00 -->15> N RANGE N RANGE >0239 ->0239 SET CAM RANGE SET CAM RANGE >0000 -->9999 >0000 -->9999 M RANGE M RANGE ->9999 ->9999 RESET DEFAULT_I? RESET DEFAULT_I? >********** >********** 01< 00 66> MUX ID MUX ID Output to Matrix Output to Matrix OUT:0001 OUT:0001 CAM:001 CAM:001 Assign to Assign to Camera ID Camera ID Monitor ID for Output Monitor ID for Output ID:01 OUT:0001 ID:01 OUT:0001 button agin the assignment for the DVR IN:01to change CAM:001 IN:01 CAM:001 Press NEXT input and Camera ID (admin. access required) MUX Input Camera ID Function Camera ID Camera ID SET KEY LEVEL SET KEY ID (mapped to DVR CH ID) (mapped ID) -->15> >01<00 -->63> to DVR CH>01<00 ID ID -->63> -->63> Set MUX ID: Select the DVR you need to control or modify 01< 00 66> Enter DVR Menu Enter Key 4 Cut 9 Cut 16 Cut Zoom Slow Playback Start Playback RESET DEFAULT_I? Playback PLEASEKey WAIT ... Pause Key Stop Key Rewind Key Forward Keyboard Information Power ON/OFF DVR Ch. Display 1# (#=0-9) Ch. Display 0# (#=0-9) Key Plus RESET DEFAULT_I? Key Minus RESET DEFAULT_I? PLEASE WAIT . . . PLEASE WAIT . . .Key Audio Key Search Key Next Clear Keyboard Screen Keylock Key Left Key Right Key Up Key Down MUX Input Channel Channel Camera ID Button Set Enter Hold Prev IRIS close Wide/Tele Key Aux ALM ON Autopan IRIS Open GRP OFF Run * 1+#+ENTER 0+#+ENTER 3D Joystick Right 3D Joystick Left Focus Near Focus Far DVR ID Setting CLR SHOT Joystick Left Joystick Right Joystick Up Joystick Down 14 Note: -Setup the communitcation baud-rate, and ID in the DVR before connection. -To prevent signal interference, it is strongly recommended to use an RS-485 distributor for connection. Multiplexer SHOT+# # 0001 0001 001 0001 0001 Control Press the MUX button to enter the Multiplexer mode. LED for MUX mode MUX_ID:01 Press MUX button to enter Multiplexer mode MUX_ID:01 IN:01 PTZ Cam:001 1 1 11 01 trix trix atrix 1 1 D U SYS MUX / WIDE PgUp DVR FAR/ PIC.L / OPEN BACK N/ ON/ OPA AUT S ZOOM FOCU IRIS OFF/ / GRP / Rx ER POW T/ SHO SET/ MEN MUX NEX / ALM / RUN / AUX T/ E/ CLOS DEL PREV D/ HOL / NEAR PIC.F / TELE PgDn RS-485 Distributor MON 3 2 CAM 1 6 5 CLR 4 9 8 R ENTE 7 0 * SET+# SHOT+# 001 0001 0001 Set MUX 001ID: 0001 0001 01< 00 66> 0 Tx > 4<01 oard VER3 Keyb em Syst DVR Up to 750m, coaxial cable Video Amplifier (optional) Monitor (optional) PTZ with Multiplexer in MUX mode Monitor ID for Output MUX ID In MUXID:01 mode,OUT:0001 press the MUX button again to enter virtual PTZ mode. You can control the PTZ by IN:01 the CAM:001 MUX_ID:01 switching input channel (the camera ID will also be switched accordingly). MUX Input Channel DVR (optional) Camera ID MUX_ID:01 IN:01 PTZ SHOT+# Cam:001 SET+# SET+# SHOT+# 001 0001 0001 001 0001 0001 001 001 ID: 0001 0001 SET+# 0001 0001 Set MUX SHOT+# 001 0001 0001 01< 0000166> 0001 0001 MUX_ID: 01:.........ID of the Multiplexer IN: 01.....................Input 1 of the Multiplexer Balun Transmitter Balun Receiver (optional) PTZ.........................Indicates(optional) the control of PTZ Cam:0001..............Camera ID Up to 1200m, twisted pair or cat5 cable DVR DIGITAL VIDEO RECORDER Monitor (optional) RS 485+ Monitor ID for Output MUX ID Setup the virtual PTZ control in MUX mode MUX_ID:01 ID:01 OUT:0001 IN:01MUX_ID:01 CAM:001 MUX_ID:01 MUX Input Camera ID ChannelMUX_ID:01 IN:01 MUX_ID:01 IN:01 PTZ Cam:001 PTZ MUX_ID:01Cam:001 IN:01 PTZMUX ID: Cam:001 Set Set 01<MUX 00 ID: 66> 01< Set 00 MUX66> ID: 01<ID00 66> Monitor ID for Output MUX MUX ID RS 485- DVR (optional) In MUX mode, press AUTOPAN to change the selected Multiplexer. Camera ID DVR DIGITAL Device 1 Device 2 Device 3 Select the MUX ID for setup (if more than one are installed), and choose the desired device. Monitor ID for Output ID:01 OUT:0001 Monitor ID for Output MUX ID ID:01 OUT:0001 IN:01 CAM:001 IN:01 CAM:001 ID:01 MUX Input OUT:0001 Camera ID IN:01 CAM:001 Channel MUX Input Camera ID Channel MUX Input Channel 120Ω Resistor 120Ω Resistor Press AUTOPAN again to setup the PTZ. (admin. access required). Press ENTER after every assignment to save the changes. Failure to do so may result in the loss of the configured settings. ? ? _I? 15 VIDEO RECORDER Basic OperationInitial Screen and Self-Testing After powered on, the dome starts the self-testing by slowly rotating and panning. After the selftest completes the initial information will be displayed on the screen. S/N:XXXXXXXXXXXXXXX CLINTON V2.42 PROTOCOL: CLINTON DOME ADDRESS: 001 COMM 9600, N, 8, 1 S/N of the PTZ Software Version Protocol Dome ID Communication Parameter The initial information will remain on the screen until a button is pressed, joystick is moved, or until “POWER UP ACTION” initiates. See next page on how to show Initial Info within system settings menu, and how to define Power up action. Open the On-Screen-Display (OSD) Menu This dome supports OSD menu for simple configuration of device settings. To enter the OSD menu, press [shot] 95 [enter] on the keyboard. Or call the sequence [shot] 9 [enter] twice within 3 seconds. If you encounter troubles, make sure your keyboard settings are correct for the camera you are trying to control, such as the CAM number on your keyboard matching the number assigned to the desired PTZ. Navigation from keyboard [IRIS OPEN] Enters the sub menu or confirms a setting [IRIS CLOSE] Exits the selected menu item or cancels the current setting. [UP], [DOWN] Move between menu lines, or adjust the selected value. [RIGHT] Enter a highlighted menu item. (same as [IRIS OPEN]) [LEFT] Moves left or exit the menu item. System Settings MAIN MENU -----------------SYSTEM SETTING --> CAMERA SETTING --> FUNCTION SETTING --> WINDOW BLANKING --> EXIT SYSTEM SETTING -----------------EDIT DOME LABEL --> INITIAL INFO --> DISPLAY SETUP --> MOTION --> CLEAR --> PASSWORD SETUP --> CLOCK SETTING --> COMM SETTING --> BACK EXIT EDIT DOME LABEL -----------------LABEL: DOME 1 BACK EXIT EDIT DOME LABEL For multiple domes in a single installation, it may be helpful to assign a name to every dome with location info. Label may contain alphanumeric values up to 16 characters long. Ensure Dome Label is set to “ON” ; see Display Setup on pg.12. - Enter OSD and select SYSTEM SETTING - Select EDIT DOME LABEL and enter the sub menu - Select LABEL and enter with [RIGHT] or [IRIS OPEN] - The input character starts to flash, use [UP] or [DOWN] to select the desired character and [RIGHT] for next input. - Available characters appear in the following order: “0” to “9”, “A” to “Z”, “:” , “<” , “>” , “-”, {SPACE} - Use [LEFT] to move to previous character if needed. - If you need to delete a character, use the {SPACE} character. - When finished, press [IRIS OPEN] , or use [RIGHT] to move to last character and then navigate to BACK or EXIT to exit the editing mode. - Select “BACK” to exit to “SYSTEM SETTING” menu. 16 INITIAL INFO -----------------S/N: XXXXXXXXXXXXXXX CLINTON V2.42 PROTOCOL: CLINTON DOME ADDRESS: 001 COMM 9600, N, 8, 1 BACK EXIT DISPLAY SETUP --------------DOME LABEL PRESET LABEL ZOOM LABEL ZONE LABEL DIRECTION LABEL TEMPERATURE LABEL TIME LABEL DATE LABEL BACK EXIT DOME LABEL PRESET LABEL INITIAL INFO Shows the serial number, current firmware version and other settings. [BACK]: Move to previous screen [EXIT]: Exit the OSD DISPLAY SETUP Customize the labels shown on the OSD --OFF OFF OFF OFF OFF OFF OFF OFF TEMP [DOME LABEL]: Shows dome label name on OSD [PRESET LABEL]: Shows the current preset label on OSD (see pg.15; “Preset”) [ZOOM LABEL]: Shows magnification setting on OSD [ZONE LABEL]: Shows current zone (must first be set up: see pg.17; “Zones”) [DIRECTION LABEL]: Shows current direction on OSD: Displayed as (Pan: 0º-359º, Tilt: 0º-90º) [TEMPERATURE LABEL]: Shows current temperature inside dome on OSD [TIME LABEL]: Shows current time on OSD. Displayed as Year/Month/Day. ZONE LABEL DIRECTION ZOOM DATE TIME [DATE LABEL]: Shows current date on OSD. Displayed as 24 hour clock. [BACK]: Move to previous screen (doing so will save your changes to display setup) [EXIT]: Exit the OSD (doing so will save your changes to display setup) MOTION -----------------AUTO FLIP OFF PROPORTION PAN OFF PARK TIME 000 PARK ACTION NONE POWER UP ACTION NONE FAN ENABLED 113 BACK EXIT MOTION The motion control includes the setting for Park Time action and other features. [AUTO FLIP]: Disabling this function will limit the tilt range to 90 degrees only [PROPORTIONAL PAN]: Pan speed adjusts accordingly to the zoom ratio. The more the operator zooms in, the slower the pan speed. The Park Time speed will be adjusted accordingly. [PARK TIME]: Sets the idle time in minutes, until [PARK ACTION] is activated. [PARK ACTION]: You can select an action that will be started after certain idle time, such as preset, tour or pattern. Select NONE to disable the function. [POWER UP ACTION]: Instructs the dome to start a predefined action when system boots up and completes the self test. This could be helpful to restore the observation after power loss. [FAN ENABLED]: Sets the temperature limit for the internal cooling fan to start. [BACK]: Move to previous screen (doing so will save your changes to motion) [EXIT]: Exit the OSD (doing so will save your changes to motion) 17 CLEAR -----------------CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WINDOWS FACTORY DEFAULTS RESTART BACK EXIT CLEAR The CLEAR function resets the stored settings and controls back to factory default. *NOTE: Pressing Right with the joystick will activate the following functions. There are no sub menus to these functions. You cannot undo the action. [CLEAR ALL ZONES]: Clear set zones [CLEAR ALL PRESETS]: Clear all stored preset positions [CLEAR ALL PATTERNS]: Clear all stored pattern tours [CLEAR ALL TOURS]: Clear all tours [CLEAR ALL WINDOWS]: Clear all privacy masking settings *[FACTORY DEFAULTS]: Reset all settings and return to factory settings [RESTART]: Restarts the system, used after resetting factory defaults [BACK]: Move to previous screen [EXIT]: Exit the OSD *NOTE: After using the FACTORY DEFAULTS option, all system settings and stored information, such as presets, tour, or patterns will be permanently erased. Please make sure this is your intention before selecting this option. PASSWORD SETUP -----------------OLD PASSWORD : ****** NEW PASSWORD : ****** CONF PASSWORD: ****** ENABLE PASSWORD OFF BACK EXIT PASSWORD SETUP In password-settings menu, you can change the password, and enable/disable the password protection function. The password function can prevent unauthorized access to the OSD and changes to the settings. It consists of a 6 digit number from 0-9, and can be disabled if so desired. 1. To modify the password, you must input the old password. The default password is 000000. 2. Enter a new password. 3. Enter the new password again in [CONF PASSWORD] to confirm. To set the password, move left/right to select a digit, and up/down to change the number. When finished, press [IRIS OPEN] on the keyboard, or move the cursor right to save the settings. A “SUCCESS” message will appear on screen when changes are saved, or your submission is correct. An “ERROR” message will appear on screen when an incorrect password is entered. 18 CLOCK SETTING -----------------TIME 13:44:30 DATE 10/03/31 BACK EXIT CLOCK SETTING The system is equipped with a RTC (Real-Time Clock) and can be used to display the date/time information on the screen, or operated via schedule (see pg.18; “Time Running”). In order to use this function correctly, you must first set up the date and time. [TIME]: Change the time setting. Displayed as 24hr clock. [DATE]: Change the date setting. Displayed as Year/Month/Day. [BACK]: Move to previous screen (doing so will save your changes to clock setting) [EXIT]: Exit the OSD (doing so will save your changes to clock setting) COMM SETTING -----------------S/N: XXXXXXXXXXXXXXX CONF:XXXXXXXXXXXXXXX SITE ID 001 COMM SPEED 9600bps PROTOCOL CLINTON BACK EXIT Camera Settings MAIN MENU -----------------SYSTEM SETTING --> CAMERA SETTING --> FUNCTION SETTING --> WINDOW BLANKING --> EXIT CAMERA SETTING -----------------ZOOM SPEED HIGH DIGITAL ZOOM ON BLC MODE OFF SLOW SHUTTER OFF ADVANCE SETTING --> BACK EXIT CAMERA SETTING -----------------ZOOM SPEED HIGH DIGITAL ZOOM ON BLC MODE OFF SLOW SHUTTER OFF ADVANCE SETTING --> BACK EXIT ADVANCE SETTING -----------------AE MODE AUTO SHUTTER N/A IRIS N/A BRIGHT N/A WB MODE AUTO R GAIN N/A B GAIN N/A BACK EXIT COMM SETTING To edit settings for Site ID, baudrate, and protocol, you must first unlock these settings by entering the serial number again into the [CONF] field. Protocol setting can be detected automatically. In this section, the camera and image related functions can be set. [ZOOM SPEED]: Zoom-in speed [DIGITAL ZOOM]: Besides the optical zoom, this PTZ is equipped with digital image enlargement, known as digital zoom. When off, only the optical zoom will be available. [BLC MODE]: Backlight compensation mode. Use this option when the observed object has a strong backlight such as sunlight, or other light source. [SLOW SHUTTER]: The slow shutter allows a higher sensitivity by exposing the image sensor a longer period of time, useful when observing objects do not have much movement. [ADVANCED SETTING]: Enters the advanced settings sub-menu for the camera. [AE MODE]: Activate auto-exposure mode for various exposure methods for different environments: - SHUTTER MODE: In shutter mode, the camera changes the shutter speed to regulate light. - IRIS MODE: Regulate the iris-opening to control the exposure. - BRIGHTNESS: Regulate the exposure by changing the brightness control - AUTO: Automatically regulates the exposure modes. [WB MODE]: The camera supports Auto, Manual, ATW, OPW, Outdoor, and Indoor modes of White Balance, which chooses the correct color of the image. *NOTE: R gain and B gain are only editable in Manual mode. - R GAIN: Regulates the red elements in the image color - B GAIN: Regulates the blue elements in the image color 19 Function Settings MAIN MENU -----------------SYSTEM SETTING --> CAMERA SETTING --> FUNCTION SETTING --> WINDOW BLANKING --> EXIT FUNCTION SETTING -----------------PRESETS --> SCAN --> PATTERNS --> TOUR --> ZONES --> TIME RUNNING --> BACK EXIT PRESETS -----------------PRESET NUMBER 001 SET PRESET --> SHOW PRESET CLEAR PRESET EDIT PRESET LABEL --> BACK EXIT In the function settings, user can setup the automated PTZ functions, such as preset position, tours, scan, etc. These functions may become very useful for your surveillance application. PRESET Preset point is a position of PTZ which can be memorized by the device and be recalled immediately, if needed. Up to 128 preset points are supported. Quickly recall a preset using the keyboard by pressing “SHOT”, the desired preset #, then “ENTER”. *NOTE: Assigning #95 to a preset will result in an error, as this number is used to call up the System Settings OSD Menu. [PRESET NUMBER]: Selected preset position [SET PRESET]: Setup the preset position. Enter this menu, move the PTZ to desired position, and press [IRIS OPEN] to store, or [IRIS CLOSE] to discard. [SHOW PRESET]: This will show the current preset defined in [PRESET NUMBER] [CLEAR PRESET]: This will delete the current preset defined in [PRESET NUMBER] [EDIT PRESET LABEL]: Assign a name to the current preset position defined in [PRESET NUMBER]. This label will show on the screen when called up. “Preset Label” must be set to “ON” for label to appear on-screen. See pg 12; “Display Setup”. [BACK]: Move to previous screen (doing so will save your changes to presets) [EXIT]: Exit the OSD (doing so will save your changes to presets) 20 SCAN -----------------SCAN NUMBER 01 SCAN SPEED 50 SET LEFT LIMIT --> SET RIGHT LIMIT --> CLEAR SCAN RUN SCAN EDIT SCAN LABEL --> BACK EXIT SCAN A Scan-Tour is an automated Pan movement between 2 defined positions with speed setting. The scan will move from the defined Left limit, to the defined Right limit in a straight path, and back again. If you wish to have your PTZ follow a more advanced path, use one of the next two selections: “PATTERN”, or “TOUR”. [SCAN NUMBER]: Current scan number [SCAN SPEED]: Define the scan speed [SET LEFT LIMIT]: Define the left point of the scan tour. To define, enter the selection and move the PTZ to desired position. Use [IRIS OPEN] to store or [IRIS CLOSE] to discard. [SET RIGHT LIMIT]: Define the right point of the scan tour. To define, enter the selection and move the PTZ to desired position. Use [IRIS OPEN] to store or [IRIS CLOSE] to discard. [RUN SCAN]: This will run the current scan defined in [SCAN NUMBER] [CLEAR SCAN]: This will erase the current scan defined in [SCAN NUMBER] [EDIT SCAN LABEL]: Assign a name to the current scan defined in [SCAN NUMBER] [BACK]: Move to previous screen (doing so will save your changes to scan) [EXIT]: Exit the OSD (doing so will save your changes to scan) PATTERNS -----------------PATTERN NUMBER 001 PROGRAM PATTERN --> RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL --> BACK EXIT PATTERN A pattern-tour is a custom tour defined by recording the user’s actions up to 180 seconds per tour. This camera can support up to 4 pattern tours. [PATTERN NUMBER]: Current pattern number [PROGRAM PATTERN]: Record the pattern tour. Enter this menu to start the tour recording, when finished, press [IRIS OPEN] to store. [RUN PATTERN]: This will run the current pattern defined in [PATTERN NUMBER] [CLEAR PATTERN]: This will erase the current pattern defined in [PATTERN NUMBER] [EDIT PATTERN LABEL]: Assign a name to the current pattern defined in [PATTERN NUMBER] [BACK]: Move to previous screen (doing so will save your changes to pattern) [EXIT]: Exit the OSD (doing so will save your changes to pattern) 21 TOUR -----------------TOUR NUMBER 001 EDIT TOUR --> RUN TOUR CLEAR TOUR BACK EXIT TOUR A Tour is an automated cruising through selected preset positions with individual speed settings and dwell times. This PTZ supports up to 4 tours with 24 positions each. *NOTE: Before a tour can be properly set up, you must first define your preset points you wish to include in the tour (see page 16 “Presets”). A tour sequence will repeat until interrupted by a movement of the joystick after it reaches a preset point, or until another command is entered (ie. [SHOT]95[ENTER] to enter menu). [TOUR NUMBER]: Current tour number EDIT TOUR PO-S-TM PO-S-TM PO-S-TM 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 BACK EXIT [EDIT TOUR]: Edit the current selected tour as defined in [TOUR NUMBER] Tour Editing: PO: The preset position being included in the tour. If there is no preset position stored, please exit, and define presets before continuing. S: The speed in which the PTZ moves to this preset. The value is between 1(slow)-8(fast). TM: The dwell time before the PTZ moves to the next point. Given in seconds. (Up to 60 sec.) [RUN TOUR]: This will run the current tour defined in [TOUR NUMBER] [CLEAR TOUR]: This will erase the current tour defined in [TOUR NUMBER] [BACK]: Move to previous screen (doing so will save your changes to tour) [EXIT]: Exit the OSD (doing so will save your changes to tour) ZONES -----------------ZONE NUMBER 001 SET LEFT LIMIT --> SET RIGHT LIMIT --> CLEAR ZONE EDIT ZONE LABEL --> BACK EXIT ZONES The zone function allows user to define a perimeter with a name tag. The perimeter is defined by setting a Left, and Right end of a desired area. When the camera enters this area, the name will be displayed on the screen, which provides better orientation in surveillance applications. Up to 8 zones are supported. Make sure “Zone Label” is set to “ON” in Display Setup; see pg12. [ZONE NUMBER]: Current zone number [SET LEFT LIMIT]: Define the left point of the zone [SET RIGHT LIMIT]: Define the right point of the zone [CLEAR ZONE]: This will erase the current zone defined in [ZONE NUMBER] [EDIT ZONE LABEL]: Assign a name to the current zone defined in [ZONE NUMBER] [BACK]: Move to previous screen (doing so will save your changes to zones) [EXIT]: Exit the OSD (doing so will save your changes to zones) 22 TIME RUNNING -----------------TIME CHANNEL 1 START TIME 00:00 END TIME 00:00 RUNNING NONE BACK EXIT TIME RUNNING The time running function is a scheduled start for predefined action, such as preset tour, scan tour, etc. This PTZ supports up to 4 schedules. Before setting this function, please make sure that the system time has been set correctly (see clock setting; pg14) [TIME CHANNEL]: Current schedule number [START TIME]: Start time of selected schedule as defined in [TIME CHANNEL] [END TIME]: End time of selected schedule as defined in [TIME CHANNEL] [RUNNING]: Define the action to be started. Select None to deactivate the function. [BACK]: Move to previous screen (doing so will save your changes to time running) [EXIT]: Exit the OSD (doing so will save your changes to time running) Window Blanking WINDOW BLANKING -----------------WINDOW NUMBER 01 EDIT WINDOW --> ENABLE WINDOW ON CLEAR WINDOW BACK EXIT The Window Blanking function is used to protect the privacy in the observed area, as this may be required by law for certain applications. It is also known as “Privacy Masking”, which covers the selected area with a blank window. This PTZ supports up to 25 masking windows. [WINDOW NUMBER]: Current window number [EDIT WINDOW]: Edit the current masking window as defined in [WINDOW NUMBER] 1. Center the area you wish to mask on the screen by using the joystick. 2. Press iris open to enter window blanking edit. 3. Use the [UP], and [DOWN] movements to increase or decrease the height of the window mask. 4. Use [LEFT], or [RIGHT] to decrease or increase the width of the window mask. 5. Press [IRIS OPEN] to save the mask. [CLEAR WINDOW]: Clear the current masking window as defined in [WINDOW NUMBER] [BACK]: Move to previous screen (doing so will save your changes to time window blanking) [EXIT]: Exit the OSD (doing so will save your changes to window blanking) 23 MAIN MENU -----------------SYSTEM SETTING --> CAMERA SETTING --> FUNCTION SETTING --> WINDOW BLANKING --> EXIT OSD Map OSD MENU INDEX SYSTEM SETTING -----------------EDIT DOME LABEL --> INITIAL INFO --> DISPLAY SETUP --> MOTION --> CLEAR --> PASSWORD SETUP --> CLOCK SETTING --> COMM SETTING --> BACK EXIT CAMERA SETTING -----------------ZOOM SPEED HIGH DIGITAL ZOOM ON BLC MODE OFF SLOW SHUTTER OFF ADVANCE SETTING --> BACK EXIT ADVANCE SETTING -----------------AE MODE AUTO SHUTTER N/A IRIS N/A BRIGHT N/A WB MODE AUTO R GAIN N/A B GAIN N/A BACK EXIT EDIT DOME LABEL -----------------LABEL: DOME 1 BACK EXIT INITIAL INFO -----------------S/N: XXXXXXXXXXXXXXX CLINTON V2.42 PROTOCOL: CLINTON DOME ADDRESS: 001 COMM 9600, N, 8, 1 BACK EXIT PRESETS -----------------PRESET NUMBER 001 SET PRESET --> SHOW PRESET CLEAR PRESET EDIT PRESET LABEL --> BACK EXIT SCAN -----------------SCAN NUMBER 01 SCAN SPEED 50 SET LEFT LIMIT --> SET RIGHT LIMIT --> CLEAR SCAN RUN SCAN EDIT SCAN LABEL --> BACK EXIT DISPLAY SETUP -----------------DOME LABEL OFF PRESET LABEL OFF ZOOM LABEL OFF ZONE LABEL OFF DIRECTION LABEL OFF TEMPERATURE LABEL OFF TIME LABEL OFF DATE LABEL OFF BACK EXIT PATTERNS -----------------PATTERN NUMBER 001 PROGRAM PATTERN --> RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL --> BACK EXIT MOTION -----------------AUTO FLIP OFF PROPORTION PAN OFF PARK TIME 000 PARK ACTION NONE POWER UP ACTION NONE FAN ENABLED 113 BACK EXIT TOUR -----------------TOUR NUMBER 001 EDIT TOUR --> RUN TOUR CLEAR TOUR BACK EXIT CLEAR -----------------CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WINDOWS FACTORY DEFAULTS RESTART BACK EXIT ZONES -----------------ZONE NUMBER 001 SET LEFT LIMIT --> SET RIGHT LIMIT --> CLEAR ZONE EDIT ZONE LABEL --> BACK EXIT PASSWORD SETUP -----------------OLD PASSWORD : ****** OLD PASSWORD : ****** OLD PASSWORD : ****** ENABLE PASSWORD OFF BACK EXIT TIME RUNNING -----------------TIME CHANNEL 1 START TIME 00:00 END TIME 00:00 RUNNING NONE BACK EXIT PASSWORD SETUP -----------------OLD PASSWORD : ****** OLD PASSWORD : ****** OLD PASSWORD : ****** ENABLE PASSWORD OFF BACK EXIT COMM SETTING -----------------S/N: XXXXXXXXXXXXXXX CONF:XXXXXXXXXXXXXXX SITE ID 001 COMM SPEED 9600bps PROTOCOL CLINTON BACK EXIT FUNCTION SETTING -----------------PRESETS --> SCAN --> PATTERNS --> TOUR --> ZONES --> TIME RUNNING --> BACK EXIT 24 WINDOW BLANKING -----------------WINDOW NUMBER 01 EDIT WINDOW --> ENABLE WINDOW ON CLEAR WINDOW BACK EXIT EDIT PRESET LABEL -----------------LABEL: PRESET-001 BACK EXIT EDIT SCAN LABEL -----------------LABEL: AUTOSCAN1 BACK EXIT EDIT PATTERN LABEL -----------------LABEL: PATTERN1 BACK EXIT PO-S-TM 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 BACK EXIT EDIT TOUR PO-S-TM PO-S-TM 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 ZONES -----------------LABEL: ZONE-1 BACK EXIT Specifications Model CE-PTZ10X Signal Format PAL / NTSC Scanning Progressive Image Sensor 1/4 inch Ex-View CCD H. Resolution 540 TVL Viewing Angle 46.0 º (Wide end) 4.6 º (Tele end) Zoom 10 x Optical / 12 x Digital Min. Illumination 1.0Lx (typical) - (F1.8, 50 IRE) Focus Auto / Manual White Balance Auto / Manual (ATW, Indoor, Outdoor, One Push WB, Manual WB) Shutter Speed 1 to 1/10,000 Sec. 22 steps Iris Control Auto / Manual / Auto Slow Shutter Gain Control Auto / Manual (-3 to 28 dB, 2 dB steps) Video Output VBS: 1.0Vp-p (Sync Negative), Y / C Output S/N Ratio More than 50 dB Pan Speed 0.4 º - 300 º per Sec. Tilt Speed 0.4 º - 150 º per Sec. Pan Range 360 º Tilt Range 0 - 90 º Communication RS-485, multiple-protocol, coax Preset Positions 128 Presets Auto Pan Tour / Sequence Yes, between 2 presets 4 progr. Tours with max 32 presets / 4 Patterns up to 180s Privacy Mask Operating Temp. 24 Position / 8 Position per Screen Outdoor: -40 ºF to 140ºF / Indoor: 14ºF to 122ºF Power DC 12V / AC 24V If you have trouble operating your camera and the guidelines in this manual do not enable you to solve the problem, contact Clinton Electronics Technical Support at 1-800-549-6393 or 815-633-1444. 25 v.09.23.11