Download Power Transmission Products

P O W E R
T R A N S M I S S I O N
P R O D U C T S
C ATA L O G
2 0 1 0
U.S.A.
Power Transmission Products
Full Line Catalog
P O W E R
T R A N S M I S S I O N
P R O D U C T S O V E R V I E W
Terms & Conditions
of
Sale
O V E R V I E W
THE INFORMATION HEREIN CONTAINED CONSTITUTES A CONFIRMATION OF CUSTOMER’S ORDER OR A CONFIRMATION OF CHANGE TO CUSTOMER’S
ORDER, AS APPLICABLE, (COLLECTIVELY “CONFIRMATION”) AND WHICH CONFIRMATION IS EFFECTIVE UPON VEYANCE’S DISPATCH OF THIS
CONFIRMATION. ANY PRIOR RECEIPT BY CUSTOMER FROM ANY OTHER SOURCE OF ALL OR PART OF THE INFORMATION HEREIN IS FOR INFORMATIONAL
PURPOSES ONLY AND DOES NOT CONSTITUTE A LEGALLY BINDING CONFIRMATION. THIS CONFIRMATION IS EXPRESSLY MADE SUBJECT TO AND IS STRICTLY
LIMITED TO THE TERMS AND CONDITIONS OF SALE STATED HEREIN AND ANY INCONSISTENT TERMS OR CONDITIONS APPEARING ON CUSTOMER’S ORDER
ARE SPECIFICALLY OBJECTED TO AND DISCLAIMED. IN ANY COMMUNICATION WITH VEYANCE REGARDING THIS ORDER, PLEASE REFER TO VEYANCE’S
DOCUMENT OR ORDER CONFIRMATION NUMBER.
1. This Confirmation and any distributor’s agreement, if any, between Customer and Veyance or Veyance affiliate, together with any specifications, schedules, exhibits, riders, or other writings
which may be annexed hereto or provided for hereunder and by reference made a part hereof, sets forth the complete and final agreement between Veyance and Customer in respect of the subject
matter hereof, and supersedes all prior understandings, assurances, and Customer’s order form, if any. THIS AGREEMENT CONTAINS THE ENTIRE UNDERSTANDING BETWEEN
CUSTOMER AND VEYANCE AND NO OTHER REPRESENTATION OR INDUCEMENT, ORAL OR WRITTEN, HAS BEEN MADE WHICH IS NOT SET FORTH HEREIN.
EXCEPT FOR THE WARRANTIES AND REPRESENTATIONS, IF ANY, SET FORTH IN THIS AGREEMENT, NO OTHER STATEMENT, WARRANTY, REPRESENTATION OR
INFORMATION, ORAL OR WRITTEN, SHALL BE LEGALLY BINDING UPON VEYANCE OR SHALL BE THE BASIS FOR RELIANCE BY CUSTOMER. CUSTOMER DOES
NOT RELY AND IS NOT RELYING UPON ANY ORAL OR WRITTEN STATEMENT, WARRANTY, OR REPRESENTATION OF VEYANCE, ITS EMPLOYEES, AGENTS, AND/
OR REPRESENTATIVES NOT FULLY SET FORTH HEREIN. No amendments or modifications of or supplements to the provisions of this Confirmation will be valid and binding upon
Veyance unless such amendment, modification, or supplement is mutually agreed to in writing and signed by an officer of Veyance and an authorized representative of Customer. In the event of any
inconsistency between these Terms and Conditions of Sale and the provisions on the other side of this document or any supplement attached hereto, the provision contained on the other side of this
document or on such supplement shall control.
2. Product sold hereunder manufactured by Veyance meets agreed specifications according to established tests performed under controlled laboratory conditions and specific test requirements.
These tests are not intended to reflect the performance of the product under actual conditions. Performance of the product as a component in a finished product may not necessarily meet the test
requirements. Due to the number and variety of applications for which any product sold hereunder may be purchased and because Veyance has no control over (or knowledge of) the conditions
under which the product may be used by others, VEYANCE DOES NOT RECOMMEND SPECIFIC APPLICATIONS OR PRODUCT DESIGNS OR ASSUME RESPONSIBILITY
FOR USE RESULTS OBTAINED OR SUITABILITY FOR SPECIFIC APPLICATIONS. No statement contained herein shall be construed as a license to operate or as a recommendation or
inducement to infringe existing patents or as an endorsement of products of specific manufacturers or systems.
3. NO RELIANCE. CUSTOMER ACKNOWLEDGES THE USE OF ITS OWN KNOWLEDGE, SKILL, JUDGMENT, EXPERTISE, AND EXPERIENCE IN (i) the selection
of the product and/or (ii) in the selection, provision, or designation of any specification or set of specifications for a product agreed upon by Customer and Veyance; and CUSTOMER
ACKNOWLEDGES THAT CUSTOMER DOES NOT RELY AND IS NOT RELYING ON ANY ORAL OR WRITTEN STATEMENTS, REPRESENTATIONS, OR SAMPLES MADE
OR PRESENTED BY VEYANCE, ITS EMPLOYEES, AGENTS, AND/OR REPRESENTATIVES TO CUSTOMER. CUSTOMER ACKNOWLEDGES THAT CUSTOMER DOES
NOT RELY AND IS NOT RELYING ON ANY KNOWLEDGE, SKILL, JUDGMENT, EXPERTISE, OR EXPERIENCE OF VEYANCE, ITS EMPLOYEES, AGENTS, AND/OR
REPRESENTATIVES IN CUSTOMER’S SELECTION OF THE PRODUCT OR IN CUSTOMER’S SELECTION, PROVISION, OR DESIGNATION OF ANY SPECIFICATION OR
SET OF SPECIFICATIONS. Without limiting the foregoing, CUSTOMER ACKNOWLEDGES THAT VEYANCE SHALL NOT BE LIABLE FOR, AND CUSTOMER ASSUMES ALL
RISK OF, INACCURATE OR UNSUITABLE SPECIFICATIONS OR INFORMATION PROVIDED, SELECTED, OR DESIGNATED BY CUSTOMER.
4. LIMITATION OF WARRANTY. PRODUCT NOT MANUFACTURED BY VEYANCE IS SOLD WITHOUT WARRANTY, “AS-IS” AND IS SUBJECT TO THE LIMITATION
OF LIABILITY SET FORTH IN SECTION 5. SUBJECT TO THE LIMITATIONS OF SECTION 5 AND UNLESS OTHERWISE EXPRESSLY PROVIDED HEREIN, product sold
hereunder that has been manufactured by Veyance, unless sold without warranty “AS-IS”, is warranted to be free from defects in material and workmanship. Subject to the preceding sentence, and
except as otherwise expressly provided herein, VEYANCE MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, AS TO MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, OR ANY OTHER MATTER WITH RESPECT TO THE PRODUCT OR ANY OTHER PRODUCT SOLD HEREUNDER, WHETHER
USED ALONE OR IN COMBINATION WITH ANY OTHER MATERIAL OR PRODUCT OR IN ANY PROCESS. VEYANCE SHALL NOT BE LIABLE FOR SPECIAL,
INCIDENTAL, AND/OR CONSEQUENTIAL DAMAGES, EVEN IF VEYANCE HAS BEEN NOTIFIED OF THE POTENTIAL OF SUCH A LOSS OR CLAIM. OTHER THAN
THOSE SPECIFICALLY SET FORTH HEREIN, THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE PRODUCTS ON THE FACE
HEREOF, EITHER EXPRESS OR IMPLIED.
5. LIMITATION OF LIABILITY OF VEYANCE AND EXCLUSIVE REMEDY. Any Veyance-manufactured product claimed to be defective in material or workmanship shall, upon Veyance’s
approval, be returned to Veyance as designated, at the Customer’s expense. VEYANCE WILL, AS THE EXCLUSIVE REMEDY, MAKE AN ADJUSTMENT FOR PRODUCT IT FINDS TO
BE DEFECTIVE IN MATERIAL OR WORKMANSHIP EITHER BY REPAIRING IT OR REPLACING IT AT AN ADJUSTMENT PRICE, OR IN LIEU THEREOF, AT VEYANCE’S
OPTION, VEYANCE MAY REFUND THE PURCHASE PRICE UPON RETURN OF THE PRODUCT. Whenever a warranty for a specific product provides that no adjustment shall be
made after a specified period of time, Veyance shall not be responsible under the terms of such warranty unless claim is made within such period of time. VEYANCE’S TOTAL RESPONSIBILITY
AND LIABILITY FOR ANY AND ALL CLAIMS, LOSSES, AND DAMAGES OF ANY KIND WHATSOEVER ARISING OUT OF ANY CAUSE WHATSOEVER (WHETHER UNDER
ANY WARRANTY OR BASED IN CONTRACT, NEGLIGENCE, OTHER TORT, STRICT LIABILITY, BREACH OF WARRANTY, OTHER THEORY, OR OTHERWISE) SHALL
NOT EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCTS IN RESPECT TO WHICH SUCH CAUSE ARISES, AND IN NO EVENT SHALL VEYANCE BE LIABLE
FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, OR PUNITIVE DAMAGES RESULTING FROM ANY SUCH CAUSE. NO EMPLOYEE, AGENT AND/OR
REPRESENTATIVE HAS AUTHORITY TO MAKE ANY REPRESENTATION, PROMISE OR AGREEMENT, EXCEPT AS STATED HEREIN. VEYANCE SHALL NOT BE LIABLE
FOR, AND CUSTOMER ASSUMES ALL LIABILITY FOR, PERSONAL INJURY AND PROPERTY DAMAGE CONNECTED WITH THE HANDLING, TRANSPORTATION, OR
FURTHER MANUFACTURE, FABRICATION, ASSEMBLY, OR PROCESSING OF THE PRODUCT.
6. Prices are subject to change without notice, and such items will be billed at prices in effect at the time of shipment. Customer will be notified of any price increase and may cancel any undelivered
portion of the order by written notice to Veyance, provided such written notice is received by Veyance not more than 10 days after your receipt of notification of the increase. Upon such cancellation
Customer shall have no liability to Veyance for the canceled portion of the order except as to product manufactured or in process, components procured by Veyance from outside sources, and special
tooling and equipment procured for performance of this order.
7. All prices are subject to increase from time to time to compensate for any tax, excise, or levy imposed upon the products sold, or upon the manufacture, sale, transportation, or delivery of them or
whenever any tax, excise, levy law, or governmental regulation has the effect, directly or indirectly, of increasing the cost of manufacture, sale, or delivery. If any government action or law should have
the effect of establishing a maximum price on product to be delivered, Veyance may, at its option and without liability to Customer, terminate its obligation with respect to future shipments upon
thirty (30) days written notice.
8. Veyance shall not be liable or deemed in default for failure to deliver or delay in delivery due to any cause beyond its reasonable control. If unable to meet delivery schedules, Veyance will endeavor
to allocate material fairly among its Customers, but reserves to itself final determination of the deliveries to be made without liability.
9. Veyance will indemnify its Customer against all claims and demands for infringement of any United States patent by the product furnished under any accepted order, provided the Customer
notifies Veyance of any patent infringement and upon request tenders Veyance the defense of the claim. CUSTOMERS WHO FURNISH SPECIFICATION TO VEYANCE AGREE TO HOLD
VEYANCE HARMLESS AGAINST ANY CLAIMS WHICH ARISE OUT OF VEYANCE’S COMPLIANCE WITH SUCH CUSTOMER SPECIFICATIONS.
10. Title to the goods shall pass to Customer upon passage of the risk of loss; provided, however, that to the extent permitted by law, until each of the goods delivered hereunder has been paid for in
full, Veyance shall retain title to the goods; however, all risk of loss and responsibility for transportation and storage, taxes, and duties shall transfer in accordance with these terms of sale. Customer
hereby agrees that notwithstanding any information shown in this confirmation regarding any estimated shipment, production, or requested date(s) for the goods, Veyance is not obligated to
produce, deliver or ship the goods by that estimated shipment, production, or requested date(s). Customer hereby agrees that unless Customer notifies Veyance in writing within ninety (90) calendar
days of the estimated shipment date as shown on the last dated Confirmation referencing the goods, there shall be a presumption that goods conforming to the goods ordered were received by
Customer.
11. Due to the varying location of the operations of Customer and Veyance and the locations that may be involved in the performance and documentation of an order to which these Terms and
Conditions of Sale are applicable, in order to settle upon and to eliminate any doubt as to the rights of the Customer and Veyance, Customer and Veyance agree that this Confirmation shall be
governed by and construed in accordance with the laws of the State of Ohio, United States of America, applicable to agreements to be performed in the State of Ohio, except that for sales or orders
originating and to be performed in Canada by Canadian subsidiaries or affiliates of The Veyance, Customer and Veyance agree that this Confirmation shall be governed by and construed in
accordance with the laws of the Province of Ontario, Canada, applicable to agreements to be performed in Canada. Customer and Veyance exclude the application of the United Nations Convention
on Contracts for the International Sale of Goods to this Confirmation and order.
P O W E R
T R A N S M I S S I O N
O V E R V I E W
P R O D U C T S Table
of
2 0 1 0
Contents
Terms and Conditions of Sale................................................................................................................................ Inside Cover
Power Transmission Products ........................................................................................................................................... 2 – 3
MaximizerPro™. .........................................................................................................................................................................4
Drive Change Tools............................................................................................................................................................ 5 – 6
Synchronous Belt Products
Introduction to Synchronous Belts............................................................................................................................................7
Eagle NRG™. .................................................................................................................................................................... 8 – 10
Eagle NRG Sprockets..................................................................................................................................................... 11 – 15
Falcon HTC®............................................................................ 8M, 14M.................................................................................16
Falcon HTC Sprockets................................................................................................................................................... 17 – 18
Hawk Pd® ................................................................................. 3M, 5M, 8M, 14M, 20M.................................................. 19 – 20
Hawk Pd Sprockets.................................................................. 3M, 5M, 8M, 14M, 20M.................................................. 21 – 24
Blackhawk Pd®.......................................................................... 8M, 14M........................................................................ 25 – 26
Blackhawk Pd Sprockets........................................................... 3M, 5M, 8M, 14M, 20M.................................................. 27 – 28
Positive Drive Pd™.................................................................... MXL, XL, L, H, XH, XXH.................................................... 29 – 34
Super Torque Pd®..................................................................... S3M, S4.5M, S5M, S8M, S14M......................................... 35 – 36
Dual Hi-Performance Pd™........................................................ 8M, 14M..............................................................................................37 – 38
Dual Positive Drive................................................................... XL, L, H. ......................................................................... 37 – 38
Open End Pd™.......................................................................... Positive Drive Pd , Falcon HTC , Hawk Pd , Super Torque Pd , Metric T Pd ...... 39 – 40
Polyurethane Belts.......................................................................................................................................................... 41 – 42
Eagle Pd® Acculinear®. ................................................................................................................................................... 43 – 46
™
®
®
®
O V E R V I E W
Overview
™
Banded Belt Products
Introduction to Banded Belts...................................................................................................................................................47
Torque Team® (Laminated)...................................................... 5VL.........................................................................................48
HY-T® Wedge Torque Team................................................... 3VX, 3V, 5VX, 5V, 8V..................................................... 49 – 50
Torque Team Plus®................................................................... 5VF, 8VF........................................................................ 51 – 52
HY-T Torque Team (Classical)................................................ BX, CX, D........................................................................ 53 – 54
Poly-V®..................................................................................... H, J, K, L, M.................................................................... 55 – 56
V-Belt Products
Introduction to V-Belts............................................................................................................................................................57
Open End V-Belting................................................................. A, B, C, D. ................................................................................58
Wedge TLP™............................................................................ 3V, 5V, 8V....................................................................... 59 – 60
HY-T Wedge............................................................................ 3VX, 3V, 5VX, 5V, 8V..................................................... 61 – 62
HY-T Plus (Classical)............................................................... A, B, C, D, E..................................................................... 63 – 65
Torque-Flex®............................................................................. AX, BX, CX....................................................................... 66 – 67
GY Metric®..................................................................................................................................................................... 68 – 70
Hex .......................................................................................... AA, BB, CC, CCP............................................................... 71 – 72
Insta-Power® (Flexten® Classical)............................................. 83, 84, 85, 87, 89.......................................................... 73 – 74
FHP........................................................................................... 2L, 3L, 4L, 5L. ................................................................ 75 – 76
Metal Sheaves/Pulleys..................................................................................................................................................... 77 – 93
Bushing Hardware
Bushings........................................................................................................................................................................ 94 – 102
Specialty Belt Products
Neothane®. ............................................................................... 3M, 5M, 7M, 11M....................................................... 103 – 104
Variable Speed............................................................................................................................................................ 105 – 106
Flat Belting (Truly Endless)........................................................................................................................................ 107 – 109
Bowling Machine . ................................................................................................................................................................110
Cotton Cleaner . ...................................................................... 61CCB, 63CCB, 64CCB, 65CCB. .............................................110
Axial Fan Pd® Belts.................................................................... 14M......................................................................................111
Axial Fan Pd Sprockets............................................................. 14M......................................................................................111
Automotive & Truck Belt Products
Gatorback® Poly-V® Belt..................................................................................................................................................... 112
Gatorback V-Belt...................................................................................................................................................................112
Timing Belt............................................................................................................................................................................113
Truck Refrigeration Belt........................................................................................................................................................113
General Information
Belt Size Information.............................................................................................................................................................114
Technical Information................................................................................................................................................ 115 – 122
Mandrel Quantity Requirements...........................................................................................................................................123
Belt Storage................................................................................................................................................................. 124 – 125 Matchmaker System..............................................................................................................................................................126
Oil & Chemical Resistance of Power Transmission Belts......................................................................................................127
Static Conductive Belts..........................................................................................................................................................128
Product Accessories & Sales Aids............................................................................................................................... 129 – 130
Warnings................................................................................................................................................................................131
1
P O W E R
T R A N S M I S S I O N
P R O D U C T S I n n o v a ti v e P r o d u ct s
O V E R V I E W
Eagle NRG™
Falcon HTC®
Goodyear Engineered Products are industry leaders with an
enviable history of product innovation and power transmission
industry firsts, including:
Falcon HTC synchronous belts — voted 2009 Product of
the Year by Plant Engineering are setting the new standard
in synchronous belt drive systems.
Eagle NRG enhanced premium synchronous belts,
with a patented H.O.T. (Helical Offset Tooth) design
for reduced noise, reduced vibration, and increased
efficiency, have increased horsepower and temperature
ratings designed to perform.
The MaximizerPro™ Drive Selection Analysis software
program for easy, accurate selection of the best moneysaving components for your application.
O V E R V I E W
We Provide Much More Than
Quality Products
Veyance Technologies is the exclusive manufacturer of
Goodyear Engineered Products. Working with us, you will
receive the high level of service and support that is critical
to stay ahead in today’s business environment. Our branded
power transmission products are available through qualified
distributors that are carefully selected and trained to provide
much more than quality Goodyear Engineered Products. A
complete selection of value-added services are available
including cost reduction programs, sales and technical support,
and inventory control programs.
Distribution
You Can Count On
Goodyear Engineered Products authorized distributors are
committed to providing you the absolute best in products and
service. They are thoroughly trained on Goodyear Engineered
Products belting and stand ready to meet all your power
transmission needs.
These distributors are backed by a staff of Goodyear Engineered
Products technical managers (GTMs) who are specially trained
and qualified to conduct in-depth studies of your current
operations. In addition, GTMs and our distributors have access
to powerful computer programs needed to optimize your current
drive/belt applications.
Wedge TLP™ provides an advanced homogeneous
construction, allowing unprecedented performance that
requires virtually no maintenance.
Take comfort in the high level of service, delivery, and technical
expertise that only comes from a local source backed by a
manufacturer with advanced worldwide research and production
capabilities.
Torque Team Plus® belts with the strength and power
transmission capacity to replace large chain drives.
C os t R e d u c t i o n P r o g r a m s
Poly-V® belts with nylon fabric rib facing, fiber-loaded
rib compounds, and fully machined rib surfaces.
Equally important, the research and development that produced
these dramatic improvements is a continuing process. We
continue to have a multitude of new innovations that are
being developed at our Research and Development Center
in Lincoln, Nebraska.
We can provide you with the tools and services to reduce your
operating costs associated with power transmission products.
Through training and drive analysis software, we can show you
how to eliminate problem drives that are bringing down your
productivity.
Customized Training
Whenever you need it, wherever you want it, customized training
is available for your associates. From maintenance and installation
clinics to in-depth training on analyzing failed power transmission
products, our distributors and GTMs can give you the guidance
needed to choose, install, and maintain your power transmission
products.
Installation, Maintenance
T r o u b l e s h oo t i n g T oo l s
That means our branded Power Transmission Products will
continue to meet the increasing demands for improved drive
efficiency, long belt life, and competitive costs.
2
and
From initial installation to routine maintenance checks, we offer
the tools that makes your job easier. Simple to use, reliable and
more important, keeping your operations productive and efficient.
P O W E R
T R A N S M I S S I O N
P R O D U C T S O V E R V I E W
2 0 1 0
We’re proud to offer you the very finest “problem solvers”
in the industry. All our distributors are factory-trained in the
applications of the products we manufacture. Our professional
design engineers are also available for consultation by calling
your local sales representative. Their combined knowledge and
experience are there for you around the clock.
Customer Satisfaction
Customer satisfaction is foremost in our guiding principles.
It shows in our services. It shows in our products. Most
importantly, it shows in the unparalleled customer quality rating
our branded power transmission products have received from
several key OEMs.
We’ve determined that the surest route to customer
satisfaction is through a constant effort to improve. This
commitment guarantees the quality of Goodyear Engineered
Products, our services, deliveries and more—both now and in the
years to come.
ISO 9001 Certified
G l ob a l S o u r c i n g
With state-of-the-art manufacturing facilities around the world,
we have the capability of meeting market demands by strategically
sourcing product to fill the product supply pipeline. You can also
count on the same quality product no matter where in the world
our products originate.
ISO 9001 is one of the most widely accepted international
standards for quality. Our belt manufacturing plants are all ISO
9001 certified.
Quality Service
Our pledge is a simple one: Quality service that you can always
depend on. It is a commitment from us and our distributors
to you.
With Veyance Technologies, you’re much more than a
customer. You are an integral piece to success. We pledge
to support you with quality products, inventory, service,
technical help, and more.
O V E R V I E W
T e c h n i c a l A ss i s t a n c e
Goodyear Engineered Products have a tradition of product
excellence. Along with our extensive distributor network,
Veyance forms a team second to none in total product and
service offerings. Our goal is to supply you with the best
products.
We are constantly looking for ways to help you save money
on your existing processes, combining your expertise with
our knowledge of power transmission products to make
every operation as efficient as possible.
Drive Change is a program we promote to maximize
efficiencies, reduce maintenance costs, and increase your
productivity. We know that it only takes minor improvements
in drive efficiency to improve your facility’s efficiency with
each energy dollar spent. To pinpoint the improvements,
we have developed easy-to-use software programs­ such as
MaximizerPro™. With MaximizerPro, mechanical
drive costs can be analyzed, thus identifying the best drive
belts for your needs.
In many instances, Drive Change involves upgrading your
drives to the latest innovative belt technology that allows
for increased efficiency and reduced cost of operation.
For example, upgrading from a standard classical V-belt
to a narrow V-belt can reduce hardware and maintenance
costs while increasing horsepower and load carrying
capabilities. To take it a step further, V-belts could be
replaced altogether with a premium synchronous belt
like Eagle NRG™or Falcon HTC , permitting less
maintenance and more efficiency.
®
3
P O W E R
T R A N S M I S S I O N
P R O D U C T S O V E R V I E W
MaximizerPro is an exciting program which allows the user to
have Goodyear Engineered Products belt specifications and
information right at their fingertips. It is easy to install and easy to
use, making drive recommendations a snap. With MaximizerPro,
drive requirements specified by the user are matched with
available belts, sprockets, pulleys, and bushings. Working like an
equation for improved performance, MaximizerPro takes specific
physical data and calculates how the system can be upgraded with
multiple options for belt drive designs. These options address the
end-user’s goals related to energy efficiency, quieter operation,
increased output, and extended life to name a few.
T h e D a t a C o l l e cti o n F o r m :
The data collection form allows you to gather all of the drive specifications
required to run the selection program. Specifications include:
• Drive Operation Time
• Horsepower Load
• DriveR and DriveN RPMs
• Center Distance
• Service Factor
• Energy Cost
T h e M a x i m i z a ti o n
Screen:
The maximization screen provides an easy way to
view, sort and print the resulting selections. From the
maximization screen, drive selections can be sorted by:
• Face Width
• Noise Level
• Energy Cost
• Service Factor
• Belt Speed
• Drive Cost Index
The Drive Design Printouts:
The printout function provides the pertinent information for the
selected drive. Information available from the detail screen includes:
• Belt, sprocket, and bushing part numbers
• Engineered drawings on all drive part numbers (where applicable)
• Drive Layout
• Installation & Maintenance Tensioning
MaximizerPro is available by visiting our website at goodyearep.com/ptp.
4
O V E R V I E W
T R A N S M I S S I O N
P R O D U C T S Power Up
O V E R V I E W
the
2 0 1 0
Value.
O V E R V I E W
P O W E R
With our Drive Change program, you’ll get the perfect mix of
technology, tools and training designed to increase value with each
purchase of power transmission products.
With Veyance Technologies and our Goodyear Power
Transmission Products Authorized Distributors, we offer an
exclusive, all-encompassing Drive Change Program that optimizes
the life and performance of your belt drives. Drive Change is
our way of ensuring you are up-to-date on required installation
and maintenance tools and procedures necessary to maximize
plant operations and optimize output where belt drives are used
to transfer power. Schedule an in-plant seminar with your local
Goodyear Engineered Products Sales Representative and dedicated
Goodyear Authorized Distributor. The next step is yours!
L a s e r A l i g n m e n t T oo l
The Goodyear Engineered Products brand Laser Alignment
Tool is fast, convenient and attaches in a few seconds, delivering
a highly visible sight line. When the laser line lies within the
target openings, the pulleys/sprockets are correctly positioned.
The result is a fast and precise alignment. Power transmission
belts including synchronous, V-belts, flatbelts and more can
be aligned equally well. The smart design of the magnetic
attachment surface also allows for alignment of both small and
large sheaves. For nonmagnetic pulleys, double-sided tape can be
used to affix the tool for an added range of applications.
Key Features & Benefits
•Detects both radial and axial misalignment
•Easier to use than conventional methods of misalignment
detection
•Affixes to most pulley and sprocket types
•Also suitable for nonmagnetic pulleys/sprockets
•Single operator friendly
TensionRite® Belt Frequency Meter
Provides a simple, repeatable and reliable method for tensioning
belts using optical technology. It displays the natural vibration
frequency of a belt so you can closely monitor belt tension. The
device calculates the corresponding belt tension in either English
or SI units.
Key Features & Benefits
• Light optics based tensioning
• Quartz crystal-based solid-state circuitry
• Direct vs. indirect measurement of vibration frequency
• Meter range matches “real-life” belt installation parameters
• Can be used with all belt types
5
P O W E R
T R A N S M I S S I O N
P R O D U C T S Power Up
the
O V E R V I E W
Value.
T e n s i o n R i t e ® S t r i ps
O V E R V I E W
Designed specifically for use with our single and banded V-belts,
TensionRite is a plastic strip that adheres to belts during
installation. Simply check the correct tension setting listed on
the back of the TensionRite card and tighten the belt. The gauge
window will indicate when the desired setting has been reached.
It’s that simple!
Key Features & Benefits
• Smarter way to quickly and accurately tension belts
• Seven easy steps to assure proper belt tensioning
• Easy-to-read measurement cards for both banded and V-belts
MaximizerPro™ Drive Selection
Analysis Program
Maximize your energy savings with MaximizerPro—the newest
and most powerful version of our exclusive drive system analysis
software. Still as simple and intuitive to use as ever, MaximizerPro
has all the features you’ve come to know, plus some new, powerful
upgrades. Data entered into the software is cross-checked against
MaximizerPro’s robust database of available belts, sprockets,
pulleys and bushings. The resulting customized report outlines
specific products that can help you reach maximum efficiency and
energy savings. MaximizerPro can enhance your drive systems the
first time and every time.
Key Features & Benefits
• Chain drive data solutions (even for old-fashioned chain
drive systems)
• Multi-pulley design to layout drive geometries for drives
with more than two pulleys
• Specific drive solutions for maximum optimization
Large Tension Tester
The Large Tension Gauge, when used with a straight edge or
tight string, can be an aid in setting the proper belt tension for a
drive system. The relationship between deflection and belt span
has been incorporated in the index scale printed on the face of
the gauge. This eliminates one calculation associated with the
tensioning operation.
Key Features & Benefits
• Quickly helps determine belt tension
• Compares force measured with recommended values for
your application
• If values are not equal, simply adjust the belt tension and
repeat force measurement until measured force matches
target value
6
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S 2 0 1 0
Synchronous Belts
Synchronous, or Positive Drive, Belts are a relatively new concept
in power transmission belting evolution. These belts combine
the advantages of chain and gear with the advantages of V-belts,
but without the limitations usually associated with these
conventional types of drives. There is minimal elongation, no
metal-to-metal contact, and no constant lubrication. Synchronous
belts are amazingly versatile with possible applications on drives
up to 600 hp and from speeds under 100 feet per minute to over
6,000 feet per minute.
Positive Drive, or Pd, is the term applied to our synchronous
belts and their method of power transmission. As the name
indicates, Positive Drive belts make possible power transmission
that is efficient and accurate to a precise degree.
The Evolution
®
of the
Positive Drive Belts also make possible important savings
in weight, space, and construction without the sacrifice of
efficiency. They are adaptable to almost any type of power
transmission drive from printers to heavy industrial milling
machines and grinders.
Engineered and manufactured with extreme care with pitch,
tooth depth, width, and other measurements accurate to a precise
degree, Positive Drive Belts are highly engineered products. The materials used in these remarkable belts consist of highstrength tension members, specially compounded rubber, and
proven synthetic fabrics. The belts are designed to eliminate
excessive heat build-up and to operate efficiently.
S Y N C H R O N O U S
Goodyear Engineered Products
Belt Line
Veyance manufactures several different designs. Some are
available as open-end constructions and some are available in
dual-sided constructions.
Positive Drive Pd® is our trademark line of trapezoidal tooth
profile synchronous belts. These belts were the first profile types
developed in the continual evolution of synchronous drive belts.
This Positive Drive product line includes a stock selection of MXL,
XL, L, H, XH, XXH, and Metric T pitches. Trapezoidal belts
make an excellent means for transmitting power; however, time and
technological advances have led to the more advanced product lines
mentioned below.
Super Torque Pd® represents the next evolution in synchronous
drive belt development in the Goodyear Engineered Products
line. The Super Torque Pd belt has a unique modified round
tooth design that minimizes tooth shear and operates quieter than
traditional trapezoidal tooth profiles. Super Torque tooth pitches
include S3M, S4.5M, S5M, S8M, and S14M and are available as
special manufacture parts with minimal runs.
Eagle NRG™ Belts and Sprockets are a unique technological
breakthrough. A patented H.O.T. (Helical Offset Tooth) design provides for continuous rolling tooth engagement, allowing the
Eagle NRG System to run quieter with less vibration than any other
synchronous belt available today. With specialized materials, Eagle
NRG offers a much higher horsepower and temperature rating
than its predecessor, Eagle Pd®. The use of a flangeless sprocket also
ensures more compact, lighter drives with precision performance.
Eagle NRG Belts and Sprockets come in a wide variety of stock
sizes with custom manufactured sizes being available for specialty
drive requirements.
Falcon HTC® is a synchronous belt designed to handle increased
horsepower, low torque applications. Falcon HTC belts feature a
high-grade rubber compound. This blended compound handles
temperatures much higher than common polyurethane belts
used in similar applications. Also, it is formulated to resist tooth
deformity and increase tooth rigidity, extending belt life and
saving you money. Falcon HTC belts also feature a patented
cord treatment which provides excellent dimensional stability
and high-impact strength. Falcon HTC belts can also be used in
applications requiring backside idlers, allowing for greater flexibility
in various applications. For ease of ordering, the Falcon HTC part
number interchanges with the Gates counterpart belt, making
replacement easy.
Hawk Pd®, with its strength and unique construction using
our advanced compounding technology, is a line of curvilinear,
synchronous belts that offers universal performance that stands
alone. Designed to fit the majority of high-capacity synchronous
application, Hawk Pd belts fulfill existing drive requirements,
matching industrial standards of belt width and length. With the
Universal Profile Design (UPD) profile, Hawk Pd performs in
the GT and HTD profiles, replacing Gates PowerGrip HTD and
PowerGrip GT 2 belts*. In addition, Hawk Pd replaces Carlisle
RPP and RPP Plus belts*, running in RPP sprockets, as well as TB
Wood’s synchronous QD profile*. The UPD is a simple solution
in satisfying the multitude of belt and sprocket combinations in
the market. Take universal performance to a higher level with
Hawk Pd.
Blackhawk Pd® is a high-performance, curvilinear belt that offers
maximum performance in your 8mm and 14mm synchronous
applications. Blackhawk Pd is precisely designed and can replace
existing Carlisle Panther®, Browning Panther, and TB Wood’s
QT PowerChain belts, matching competitive offerings of belt
width and length. Dynamic testing of Blackhawk Pd has shown
this durable belt actually lasts 3 to 4 times longer than Carlisle
RPP Panther®. Maximize the performance of your timing belt
application with Blackhawk Pd, designed to deliver longer life and
less maintenance. Choose the belt that takes performance to greater
heights—Blackhawk Pd.
*Trademarks of the Gates Corporation, Carlisle, and TB Wood’s Incorporated respectively.
7
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
E a g l e NRG
EW
N
™
A pp l i c a t i o n s
S Y N C H R O N O U S
Eagle NRG belts and sprockets are ideal on a wide variety
of applications in all industries.
• Agricultural Equipment
• Paper Presses
• Packaging Conveyors
• Hog Dehairers
• Aggregate Crushers
• Chain Drives
• Poultry/Meat Grinders
• Baking Mixers
• Wood Debarkers and Saws
• Textile Machines
• Mining Equipment
• Horizontal Drives
• Aluminum/Steel Conveyors
• Printing Machines
Part No: B-1750
B
Blue = 14 mm Pitch, 35 mm Width
1750 1750 mm Pitch Length
The Evolution Continues with the
Next Generation in Synchronous
Belt Technology
Eagle NRG is the next generation in synchronous belt
technology. This unique, state-of-the-art alternative to straighttooth belts and drive chains has been enhanced to improve the
overall performance of your drive design—and help you save
Energy (NRG).
• Reduced Noise
• Increased Horsepower
• Higher Efficiency
• Less Bearing Load
• Greater Precision
• Higher Temperature Operation
• Less Vibration
• Less Maintenance
• Compactness
• Self-Tracking
• Bidirectional
•Static Conductive*
B e l t M a t e r i a l s C o m po u n d e d
to Last Longer
Durability starts with the Eagle NRG belt’s rubber compound, a
cross-linked elastomer formulated to resist tooth deformity and
increase tooth rigidity. Eagle NRG is also chemically stable to resist
the effects of oils, coolants, heat, and ozone.
Eagle NRG is the same H.O.T. (Helical Offset Tooth) design
offering continuous rolling tooth engagement, ensuring a much
quieter, synchronous drive with reduced vibration. A flangeless
sprocket offering used with Eagle NRG also provides a reduced
weight, more compact drive providing efficiencies up to 98%.
Eagle NRG’s high-strength Flexten tensile member provides
optimal resistance to flex fatigue, elongation, and shock loads while
operating at high torque conditions. The facing of Eagle NRG
belts also reduce tooth engagement friction while standing up to
oil and chemical permeation.
H i g h e r H o r s e po w e r R a t i n g
Increased Efficiency
O ppo r t u n i t y
With the emergence of higher horsepower requirements and
the need to reduce the size of drives, Eagle NRG’s increased
horsepower capacity, up to 25% improvement, has the ability to
handle an even wider variety of applications. Newly engineered
materials and specialty compounds are formulated to give this
next-generation Eagle belt more value in the most demanding
applications.
Improved Operating
Temperature Range
Knowing that elevated temperatures can significantly reduce
belt life, we have made improvements in Eagle NRG’s ability
to perform at 200ºF continuous operation and withstand peak
temperatures as high as 300ºF.
With Eagle NRG, you can experience a whole new level of
performance and value in reinforced rubber synchronous belts.
To learn more visit www.goodyearep.com/ptp.
8
Key Features & Benefits
*Drive conditions and service variables in combination with time in
operation can result in a loss of static conductivity. It is recommended that
a conductivity check be added to drive preventive maintenance programs
where belt static conductivity is a requirement.
The unique tooth configuration of Eagle NRG provides continuous
tooth engagement and eliminates slippage. With a power
efficiency rating of 98%, Eagle NRG can offer you an impressive
5% edge over typical V-belt drives.
Simply stated, with Eagle NRG, you get what you pay for
with each energy dollar. This is especially true when the Eagle
NRG is applied to high-energy consuming drives that are used 24
hours a day, as well as high horsepower drives that inflate energy
consumption during peak periods.
A Quieter,
Reduced Vibration Drive
The H.O.T. design of Eagle NRG belts and sprockets reduces
vibration and decreases operating noise by as much as 19 decibels
versus other synchronous systems. This can lead to a quieter
working environment with improved worker efficiency. Costs
associated with monitoring, training, and testing to meet OSHA
regulations can be virtually eliminated with Eagle NRG drives.
!
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S 2 0 1 0
E a g l e NRG
™
Unlike chain drives, Eagle NRG belts and sprockets do not require
lubrication. After initial run in and rechecking tension after 8
hours of operation, Eagle NRG belts do not need additional
retensioning like V-belts and chain.
Belt Part Number Nomenclature
Matching Belt to Sprocket
Has Never Been Easier
The Eagle NRG Color Spectrum System makes it the easiest
power transmission drive to sell, purchase, and install.
The part numbering system for Eagle NRG centers around a
color-coded sizing system for the belts and sprockets. Each belt
and sprocket part number includes a letter corresponding to a
color and is also branded in that color. The letters Y, W, P, B, G,
O, and R indicate the colors Yellow, White, Purple, Blue, Green,
E a g l e NRG Y e l l o w
Part Number
No. of Teeth
Y-640
Y-720
Y-800
Y-896
Y-1000
Y-1120
Y-1200
80
90
100
112
125
140
150
Orange and Red. All Yellow belts are designed to function with all
Yellow sprockets, as is the case for the White, Purple, Blue, Green,
Orange and Red sizes. An example of the part numbering system
nomenclature for belts, sprockets, and bushings follows and also
appears on subsequent pages.
G – 2800
G
Green Color
2800 2800 mm Pitch Length
Y – 896
Y
896
(8 mm Pitch – 16 mm Width)
Part Number
25.20
28.35
31.50
35.28
39.37
44.09
47.24
Y-1280
Y-1440
Y-1600
Y-1792
Y-2000
Y-2240
Y-2400
16mm
The belt length in mm is given in the part number.
Part Number
No. of Teeth
W-640
W-720
W-800
W-896
W-1000
W-1120
W-1200
80
90
100
112
125
140
150
P-720
P-800
P-896
P-1000
P-1120
90
100
112
125
140
160
180
200
224 35mm
250
280
300
8mm
Pitch
Part 35mm
Number
Length (in)
25.20
28.35
31.50
35.28
39.37
44.09
47.24
8mm
Pitch
W-1280
W-1440
W-1600
W-1792
W-2000
W-2240
70mm
W-2400
5.3mm
32mm
8mm
(8 mm Pitch – 64 mm Width) Pitch
Part Number
Length (in)
35mm
14mm
8.6mmP-1200
28.35
Pitch P-1280
31.50
35.28
39.37
44.09
P-1440
P-1600
52.5mm
14mm
Pitch
70mm
The belt length in mm is given in the part number.
14mm
Pitch
8.6mm
105mm
8mm
Pitch
5.3mm
Length (in)
50.39
56.69
62.99
70.55
14mm
78.74
Pitch
88.19
94.49
32mm
14mm
8mm
Pitch
Pitch
52.5mm
8.6mm
5.3mm
105mm
No. of Teeth
Length (in)
14mm
160 8.6mm
Pitch
180
50.39
56.69
62.99
70.55
78.74
14mm
88.19
Pitch
94.49
200
224
52.5mm
250
280
300
14mm
Pitch
8mm
Pitch
8.6mm
5.3mm
70mm
(8 mm Pitch – 32 mm Width)
E a g l e NRG P u r p l e
No. of Teeth
No. of Teeth
32mm
16mm
The belt length in mm is given in the part number.
Part Number
Yellow Color
896 mm Pitch Length
16mm
Length (in)
E a g l e NRG W h it e
S Y N C H R O N O U S
L o w e r M a i n t e n a n c e C os t s
Purple
14mm
Pitch
64mm
14mm
Pitch
8.6mm
Purple
8.6mm
105mm
5.3mm
64mm
No. of Teeth
150
160
180
200
8mm
14mm
Pitch
Pitch
5.3mm
8.6mm
Length (in)
47.24
50.39
56.69
62.99
8.6mm
9
8m
Pit
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
16mm
E a g l e NRG
™
E a g l e NRG B l u e
S Y N C H R O N O U S
Part Number
No. of Teeth
B-994
B-1120
B-1190
B-1260
B-1400
B-1568
B-1750
B-1960
B-2100
71
80
85
90
100
112
125
140
150
(14 mm Pitch – 35 mm Width)
39.13
44.09
46.85
49.61
55.12
61.73
68.90
77.17
82.68
Part Number
B-2240
B-2380
B-2520
B-2660
B-2800
B-3136
B-3304
B-3500
B-3920
No. of Teeth
16mm
35mm
The belt length in mm is given in the part number.
E a g l e NRG G r e e n
Part Number
No. of Teeth
G-994
G-1120
G-1190
G-1260
G-1400
G-1568
G-1750
G-1960
G-2100
71
80
85
90
100
112
125
140
150
14mm
Pitch
39.13
44.09
46.85
49.61
55.12
61.73
68.90
77.17
82.68
16mm
No. of Teeth
14mm
160
Pitch
G-2240
G-2380
G-2520
G-2660
G-2800
G-3136
G-3304
G-3500
G-3920
The belt length in mm is given in the part number.
Part Number
No. of Teeth
O-1120
O-1190
O-1260
O-1400
O-1568
O-1750
O-1960
O-2100
O-2240
80
85
90
100
112
125
140
150
160
(14 mm Pitch – 70 mm Width)
Part Number
Length (in)
44.09
46.85
49.61
55.12
61.73
68.90
77.17
82.68
88.19
O-2380
O-2520
O-2660
O-2800
O-3136
O-3304
O-3500
O-3920
Part Number
No. of Teeth
R-1260
R-1400
R-1568
R-1750
R-1960
R-2100
R-2240
R-2380
90
100
112
125
140
150
160
170
35mm
8mm
Pitch
14mm
Pitch
14mm
Pitch
8mm (in)5.3mm
Length
Pitch
88.19
93.70
99.21
104.72
110.24
14mm
Pitch
123.46
14mm
130.08
Pitch
137.80
154.33
32mm
70mm
170
180
14mm
190
8.6mm
Pitch
200
224
52.5mm
236
250
280
14mm
Pitch
Length (in)
49.61
55.12
61.73
68.90
77.17
82.68
88.19
93.70
8.6mm
52.5mm
105mm
Length
8mm (in)
Pitch
93.70
99.21
104.72
110.24
123.46
130.08
14mm
137.80
Pitch
154.33
14mm
Pitch
R-2520
R-2660
R-2800
R-3136
R-3304
R-3500
R-3920
180
190
200
224
236
250
280
14mm
Pitch
8.6
8.6mm
5.3mm
Length (in)
99.21
104.72
110.24
123.46
130.08
137.80
154.33
64mm
14mm
Pitch
8.6mm
8.6mm
No. of Teeth
5.3
8.6mm
105mm
Part Number
8mm
Pitch
Purple
14mm
Pitch
32mm
8
8.6mm
5.3mm
(14 mm Pitch – 105 mm Width)
The belt length in mm is given in the part number.
10
105mm
No. of Teeth
35mm
The belt length in mm is given in the part number.
E a g l e NRG R e d
52.5mm
88.19
14mm
8
93.70
Pitch
99.21
Purple
104.72
14mm
110.24
8.6mm
Pitch
123.46
64mm
105mm
130.08
8mm
8mm
5.3mm
Pitch
Pitch
137.80
154.33
70mm
16mm
E a g l e NRG O r a n g e
8.6mm
170
180
190
200
224
236
250
280
5
8.6mm
8.6mm
70mm
Part Number
Length (in)
14mm
Pitch
8mm
Pitch
Length (in)
160
170
70mm
180
8mm
5.3mm
190
Pitch
200
224
32mm
236
250
280
52.5mm
(14 mm Pitch – 52.5 mm Width)
5.3mm
32mm
35mm
Length (in)
8mm
Pitch
8.6mm
8mm
Pitch
8.6
!
P O W E R
NE
W
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
E a g l e NRG S p r o c k e t s
™
A pp l i c a t i o n s
Eagle NRG belts and sprockets are ideal for use on a
wide variety of applications in all industries.
S Y N C H R O N O U S
Key Features & Benefits
M A T C H I N G B E L T T O S P R O C K E T H A S N E V E R B E EN EASIER!
• More design flexibility with more compact drives.
• No flanges.
• Self-tracking design.
• Available in ductile iron, aluminum, steel, or
stainless steel.
Sprocket Part Number
Nomenclature
Part No: Y-28S-H
Y
Yellow = 8 mm Pitch, 16 mm Width
28
28 Teeth
S
Sprocket
H
Hub/Bushing Type
Sprocket Combinations to Fit
Your Drive System’s Needs
Eagle NRG sprockets have been designed to insure maximum
service life and performance. Over 1,500 sprocket combinations
are available, making it easier to match the desired design speed.
More speed ratio options also means more design flexibility and
more compact drives.
Eagle NRG sprockets do not require flanges and are stocked in
ductile iron constructions. Other materials such as aluminum,
steel, and stainless steel are available upon request as made-toorder items.
Minimum Plain Bore, MPB:
O-40S-MPB
This is an Orange size sprocket with 40 teeth and a Minimum
Plain Bore (MPB) style hub. The MPB style sprockets are supplied
with a minimum bore, typically 1⁄2˝ or 1˝ with H7 tolerances, and
will require machining of a keyway and setscrew holes, and possibly
boring to a desired bore size.
Quick Disconnect, QD:
R-168S-N
This is a Red size sprocket with 168 teeth and a hub machined to
fit an “N” size QD bushing. A bushing is required to install this
sprocket on a shaft. Please note that smaller diameter sprockets are
not available in the QD style due to space limitations.
Finished Stock Bore, FSB:
G-34S — 17⁄8
This is a Green size sprocket with 34 teeth and a Finished Stock
Bore (FSB) style hub featuring a bore of 1 7/8”. FSB sprockets are
supplied ready to install with a standard keyway and setscrew holes
machined.
B-28S-BTS — 113⁄16
Bored To Suit, BTS:
This is a Blue size sprocket with 28 teeth and a hub that has been
bored (BTS) to 113⁄16˝, per customer specification, and machined
for setscrew holes and a keyway. BTS sprockets can be made to
almost any bore including metric sizes.
Note: All MPB-, QD-, and FSB-style sprockets are stock items.
BTS sprockets are made to order and may require lead times.
Matching Belt to Sprocket
Has Never Been Easier
Bushing Part Number Nomenclature
The part numbering system for Eagle NRG centers around a
color-coded sizing system for the belts and sprockets. Each belt
and sprocket part number includes a letter corresponding to a
color and is also branded in that color. The letters Y, W, P, B, G,
O and R indicate the colors Yellow, White, Purple, Blue, Green,
Orange, and Red. All Yellow belts are designed to function with
all Yellow sprockets, as is the case for the White, Purple, Blue,
Green, Orange, and Red sizes. An example of the part numbering
system nomenclature for sprockets and bushings is given below.
E 21⁄8:
E
Bushing Size
21⁄8
Bushing Bore
Bushings are supplied with bolts, lock washers, and set screws. Keys
are supplied only if a special shallow key is required. The E 21⁄8˝
bushing can be used to install any sprocket with an “E” hub on a
21⁄8˝ shaft. The QD bushing system is an industry standard,
however, to ensure the best match between sprocket and bushing,
we recommend using bushings supplied by Veyance for Eagle NRG
sprockets.
11
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S E a g l e NRG S p r o c k e t s
™
17mm
17mm
33mm
33mm
S Y N C H R O N O U S
8mm
8mm8mm
8mm
Y e l l o w72mm
72mm W h it e
E a g l e NRG Y e l l o w
Part
Number
Y-18S-MPB
Y-18S-FSB
Y-20S-MPB
Y-20S-FSB
Y-22S-MPB
Y-22S-FSB
Y-24S-MPB
Y-24S-FSB
Y-25S-MPB
Y-25S-FSB
Y-26S-MPB
Y-26S-FSB
No. of
Teeth
18
18
20
20
22
22
24
24
25
25
26
26
(8 mm Pitch – 17 mm Width)
Part
No. of Part
Number
Teeth
Number
Y-40S-MPB
Y-28S-MPB
28
Y-40S-SH
Y-28S-H*
28
Y-44S-MPB
Y-30S-MPB
30
Y-45S-MPB
Y-30S-H*
30
Y-45S-SDS
Y-32S-MPB37mm
3237mm
Y-48S-MPB
Y-32S-H*
32
Y-48S-SDS
Y-34S-MPB
34
Y-50S-MPB
Y-34S-H*
34
Y-50S-SDS
Y-36S-MPB
36
Y-52S-MPB
Y-36S-SH
36
Y-56S-MPB
Y-38S-MPB
38
Y-56S-SDS
Y-38S-SH
38
14mm
14mm
No. of Part
No. of
Teeth
Number
Teeth
14
Y-60S-MPB
60
40
14 Y-60S-SDS
60
40 mm
mm
Y-63S-MPB
63
44
Y-63S-SDS
63
45
Y-64S-MPB
64
45 54.5mm
54.5mm
Y-68S-MPB
68
48
Y-72S-MPB
72
48
Y-75S-MPB
75
50
Y-75S-SDS
75
50
Y-76S-MPB
76
52
Y-80S-MPB
80
56
14
14
Y-80S-SDS
80
56
107mm
(8 mm Pitch –107mm
33 mm
Width)
No. of
Teeth
28
28
30
30
32
32
34
34
36
36
38
38
W-18S-MPB
W-18S-FSB
W-20S-MPB
W-20S-FSB
W-22S-MPB
W-22S-FSB
W-24S-MPB
W-24S-FSB
W-25S-MPB
W-25S-FSB
W-26S-MPB
W-26S-FSB
No. of
Teeth
18
18
20
20
22
22
24
24
25
25
26
26
Part
Number
W-28S-MPB
W-28S-H*
W-30S-MPB
W-30S-H*
W-32S-MPB
W-32S-H*
W-34S-MPB
W-34S-SH
W-36S-MPB
W-36S-SH
W-38S-MPB
W-38S-SH
Part
Number
W-40S-MPB
W-40S-SH
W-44S-MPB
W-45S-MPB
W-45S-SDS
W-48S-MPB
W-48S-SDS
W-50S-MPB
W-50S-SDS
W-52S-MPB
W-56S-MPB
W-56S-SK
Part
No. of
Number
Teeth
Y-90S-MPB
90
Y-90S-SK
90
Y-112S-MPB 112
Y-112S-SK
112
65mm 140
65mm
Y-140S-MPB
Y-140S-SK
140
Y-180S-MPB 180
Y-180S-SF
180
Y-224S-MPB 224
Y-224S-E
224
mm
mm
E a g l e NRG W h it e
Part
Number
No. of
Teeth
40
40
44
45
45
48
48
50
50
52
56
56
Part
Number
W-60S-MPB
W-60S-SK
W-63S-MPB
W-63S-SK
14 14
W-64S-MPB
mmmm
W-68S-MPB
W-72S-MPB
W-75S-MPB
W-75S-SF
W-76S-MPB
W-80S-MPB
W-80S-SF
8mm
8mm
No. of
Teeth
60
60
63
63
64
68
72
75
75
76
80
80
No. of
Teeth
48
50
52
54
56
58
60
63
64
Part
Number
W-90S-MPB
W-90S-SF
W-112S-MPB
W-112S-SF
W-140S-MPB
W-140S-E
W-180S-MPB
W-180S-E
W-224S-MPB
W-224S-F
No. of
Teeth
90
90
112
112
140
140
180
180
224
224
E a g l e NRG W h it e S l a b S p r o c k e t s
Part
Number
W-18S-SLB
W-19S-SLB
W-20S-SLB
W-21S-SLB
W-22S-SLB
W-23S-SLB
W-24S-SLB
W-25S-SLB
W-26S-SLB
No. of
Teeth
18
19
20
21
22
23
24
25
26
Part
Number
W-27S-SLB
W-28S-SLB
W-29S-SLB
W-30S-SLB
W-31S-SLB
W-32S-SLB
W-33S-SLB
W-34S-SLB
W-35S-SLB
No. of
Teeth
27
28
29
30
31
32
33
34
35
Part
Number
W-36S-SLB
W-37S-SLB
W-38S-SLB
W-39S-SLB
W-40S-SLB
W-42S-SLB
W-44S-SLB
W-45S-SLB
W-46S-SLB
No. of
Teeth
36
37
38
39
40
42
44
45
46
Part
Number
W-48S-SLB
W-50S-SLB
W-52S-SLB
W-54S-SLB
W-56S-SLB
W-58S-SLB
W-60S-SLB
W-63S-SLB
W-64S-SLB
*“H” is a Split Taper Bushing. “QT” is a QD® Bushing and is interchangeable with an “H” bushing.
FSB = Finish Stock Bore
See page 15 for sizing information.
12
Part
Number
W-68S-SLB
W-70S-SLB
W-72S-SLB
W-75S-SLB
W-76S-SLB
W-80S-SLB
W-90S-SLB
No. of
Teeth
68
70
72
75
76
80
90
72mm
8mm
8mm
72mm
P O W E R
T R A N S M I S S I O N
8mm
72mm
S Y N C H R O N O U S
P R O D U C T S E a g l e NRG S p r o c k e t s
™
14
mm
107mm
Eagle
Part
Number
14
P-24S-MPB
mm
P-25S-MPB
P-26S-MPB
P-28S-MPB
P-30S-MPB
Purple
NRG P u r p l e
No. of
Teeth
24
25
26
28
30
Part
Number
P-32S-MPB
P-34S-MPB
P-36S-MPB
P-38S-MPB
P-40S-MPB
65mm
54.5mm
37mm
1414
mm
mm
14mm
14mm
8mm
65mm
54.5mm
37mm
65mm
14
mm
14
mm14
mm
54.5mm
m
2 0 1 0
Blue
107mm
107mm
8mm
8mm
Green
(8 mm Pitch – 65 mm Width)
No. of
Teeth
32
34
36
38
40
Part
Number
P-44S-MPB
P-45S-MPB
P-48S-MPB
P-50S-MPB
P-52S-MPB
No. of
Teeth
44
45
48
50
52
S Y N C H R O N O U S
mm
Part
No. of Part
Number
Teeth
Number
14 P-68S-MPB
P-56S-MPB
1456
P-60S-MPB mm
60mm P-72S-MPB
P-63S-MPB
63
P-64S-MPB
64
No. of
Teeth
68
72
E a g l e NRG P u r p l e S l a b S p r o c k e t s
Part
Number
P-25S-SLB
P-26S-SLB
P-27S-SLB
P-28S-SLB
P-29S-SLB
P-30S-SLB
P-31S-SLB
P-32S-SLB
No. of
Teeth
25
26
27
28
29
30
31
32
Part
Number
P-33S-SLB
P-34S-SLB
P-35S-SLB
P-36S-SLB
P-37S-SLB
P-38S-SLB
P-39S-SLB
P-40S-SLB
E a g l e NRG B l u e
Part
Number
B-28S-MPB
B-28S-SK
B-30S-MPB
B-30S-SK
B-32S-MPB
B-32S-SK
B-34S-MPB
B-34S-SK
B-36S-MPB
No. of
Teeth
28
28
30
30
32
32
34
34
36
No. of
Teeth
33
34
35
36
37
38
39
40
Part
Number
P-42S-SLB
P-44S-SLB
P-45S-SLB
P-46S-SLB
P-48S-SLB
P-50S-SLB
P-52S-SLB
P-54S-SLB
No. of
Teeth
42
44
45
46
48
50
52
54
Part
Number
P-56S-SLB
P-58S-SLB
P-60S-SLB
P-63S-SLB
P-64S-SLB
P-68S-SLB
P-70S-SLB
P-72S-SLB
No. of
Teeth
56
58
60
63
64
68
70
72
Part
Number
P-75S-SLB
P-76S-SLB
P-80S-SLB
P-90S-SLB
No. of
Teeth
75
76
80
90
(14 mm Pitch – 37 mm Width)
Part
Number
B-36S-SF
B-38S-MPB
B-38S-SF
B-40S-MPB
B-40S-SF
B-43S-MPB
B-43S-SF
B-45S-MPB
B-45S-SF
No. of
Teeth
36
38
38
40
40
43
43
45
45
Part
Number
B-48S-MPB
B-48S-SF
B-50S-MPB
B-50S-E
B-56S-MPB
B-56S-E
B-60S-MPB
B-60S-E
B-63S-MPB
No. of
Teeth
48
48
50
50
56
56
60
60
63
E a g l e NRG G r e e n
(14 mm Pitch – 54.5 mm Width)
Part
Number
No. of
Teeth
No. of
Teeth
G-28S-MPB
G-28S-FSB
G-30S-MPB
G-30S-FSB
G-30S-SK
G-32S-MPB
G-32S-FSB
G-32S-SK
G-34S-MPB
G-34S-FSB
28
28
30
30
30
32
32
32
34
34
34
36
36
38
38
40
40
43
43
45
Part
Number
G-34S-SK
G-36S-MPB
G-36S-SF
G-38S-MPB
G-38S-SF
G-40S-MPB
G-40S-SF
G-43S-MPB
G-43S-E
G-45S-MPB
Part
Number
G-45S-E
G-48S-MPB
G-48S-E
G-50S-MPB
G-50S-E
G-56S-MPB
G-56S-E
G-60S-MPB
G-60S-E
G-63S-MPB
No. of
Teeth
45
48
48
50
50
56
56
60
60
63
Part
Number
B-63S-F
B-71S-MPB
B-71S-F
B-75S-MPB
B-75S-F
B-80S-MPB
B-80S-F
B-90S-MPB
B-90S-F
Part
Number
G-63S-F
G-71S-MPB
G-71S-J
G-75S-MPB
G-75S-J
G-80S-MPB
G-80S-J
G-90S-MPB
G-90S-J
G-112S-MPB
No. of
Teeth
63
71
71
75
75
80
80
90
90
No. of
Teeth
63
71
71
75
75
80
80
90
90
112
Part
No. of
Number
Teeth
B-112S-MPB 112
B-112S-F
112
B-140S-MPB 140
B-140S-J
140
B-168S-MPB 168
B-168S-J
168
B-180S-E*
180
B-200S-E*
200
B-224S-E*
224
Part
Number
G-112S-J
G-140S-MPB
G-140S-M
G-168S-MPB
G-168S-M
G-180S-F*
G-200S-F*
G-224S-F*
No. of
Teeth
112
140
140
168
168
180
200
224
*Special lightweight design. Contact Veyance Technologies to ensure suitability for your application.
Sprockets with MPB (Minimum Plain Bore) are specified when the sprocket does not allow room for a bushing that will handle the maximum load.
FSB = Finish Stock Bore
See page 15 for sizing information.
13
P O W E R
65mm
54.5mm
37mm
17mm
T R A N S M I S S I 33mm
O N P R O D U C T S S Y N C H R O N O U S
E a g l e NRG S p r o c k e t s
™
8mm
14
mm
14mm
8mm
72mm
107mm
S Y N C H R O N O U S
14
mm
E a g l e NRG O r a n g e
Part
Number
O-28S-MPB
O-28S-FSB
O-30S-MPB
O-30S-FSB
O-32S-MPB
O-32S-FSB
O-34S-MPB
O-34S-FSB
O-36S-MPB
No. of
Teeth
28
28
30
30
32
32
34
34
36
Part
Number
Part
Number
R-28S-MPB
R-28S-FSB
R-30S-MPB
R-30S-FSB
R-32S-MPB
R-32S-FSB
R-34S-MPB
R-34S-FSB
R-36S-MPB
R65mm
ed
No. of
Teeth
28
28
30
30
32
32
34
34
36
(14 mm Pitch – 72 mm Width)
No. of
Teeth
O-36S-FSB
36
38
O-38S-FSB
38
O-40S-MPB
107mm 40
O-40S-FSB
40
O-43S-MPB
43
O-43S-E
43
O-45S-MPB
45
O-45S-E
45
O-38S-MPB
14mm
E a g l e NRG R e d
14
mm
O r a n g e54.5mm
37mm
8mm
Part
Number
14
O-48S-MPB
mm
O-48S-E
O-50S-MPB
O-50S-F
O-56S-MPB
O-56S-F
O-60S-MPB
O-60S-J
O-63S-MPB
14
mm
No. of
Teeth
48
48
50
50
56
56
60
60
63
Part
Number
No. of
Teeth
O-63S-J
63
O-71S-MPB 8mm
71
O-71S-J
71
O-75S-MPB
75
O-75S-J
75
O-80S-MPB
80
O-80S-J
80
O-90S-MPB
90
O-90S-J
90
Part
Number
O-112S-MPB
O-112S-M
O-140S-MPB
O-140S-M
O-168S-MPB
O-168S-M
No. of
Teeth
112
112
140
140
168
168
(14 mm Pitch – 107 mm Width)
Part
Number
R-36S-FSB
R-38S-MPB
R-38S-FSB
R-40S-MPB
R-40S-FSB
R-43S-MPB
R-43S-FSB
R-45S-MPB
R-45S-F
No. of
Teeth
36
38
38
40
40
43
43
45
45
Part
Number
R-48S-MPB
R-48S-F
R-50S-MPB
R-50S-J
R-56S-MPB
R-56S-J
R-60S-MPB
R-60S-J
R-63S-MPB
No. of
Teeth
48
48
50
50
56
56
60
60
63
Part
Number
R-63S-J
R-71S-MPB
R-71S-M
R-75S-MPB
R-75S-M
R-80S-MPB
R-80S-M
R-90S-MPB
R-90S-M
No. of
Teeth
63
71
71
75
75
80
80
90
90
Part
Number
No. of
Teeth
R-112S-MPB
R-112S-M
R-140S-MPB
R-140S-N
R-168S-MPB
R-168S-N
112
112
140
140
168
168
E a g l e NRG R e d S l a b S p r o c k e t s
Part
Number
No. of
Teeth
Part
Number
No. of
Teeth
Part
Number
No. of
Teeth
Part
Number
No. of
Teeth
R-28S-SLB
R-29S-SLB
R-30S-SLB
R-31S-SLB
R-32S-SLB
R-33S-SLB
R-34S-SLB
28
29
30
31
32
33
34
R-35S-SLB
R-36S-SLB
R-37S-SLB
R-38S-SLB
R-39S-SLB
R-40S-SLB
R-42S-SLB
35
36
37
38
39
40
42
R-43S-SLB
R-44S-SLB
R-45S-SLB
R-46S-SLB
R-48S-SLB
R-50S-SLB
R-52S-SLB
43
44
45
46
48
50
52
R-54S-SLB
R-56S-SLB
R-58S-SLB
R-60S-SLB
R-63S-SLB
R-70S-SLB
R-71S-SLB
54
56
58
60
63
70
71
Part
Number
No. of
Teeth
R-75S-SLB
R-80S-SLB
R-90S-SLB
75
80
90
Sprockets with MPB (Minimum Plain Bore) are specified when the sprocket does not allow room for a bushing that will handle the maximum load.
FSB = Finish Stock Bore
See page 15 for sizing information.
14
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
E a g l e NRG
Finished Stock Bore Sizes
Sprocket
Size
7⁄8˝
17⁄8˝
13⁄8˝
Stock Bore Sizes (in.)
15⁄8˝
17⁄8˝
Y-18S
X
W-18S
X
Y-20S
X
X
W-20S
X
X
Y-22S
X
X
W-22S
X
X
Y-24S
X
X
X
W-24S
X
X
X
Y-25S
X
X
X
W-25S
X
X
X
Y-26S
X
X
X
X
W-26S
X
X
X
X
G-28S
O-28S
R-28S
G-30S
O-30S
R-30S
G-32S
O-32S
R-32S
G-34S
O-34S
R-34S
O-36S
R-36S
O-38S
R-38S
O-40S
R-40S
R-43S
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
21⁄8˝
23⁄8˝
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
27⁄8˝
S Y N C H R O N O U S
™
X
X
X
X
X
X
X
X
X
X
X
X
X
X = Stock Size
15
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S F a l c o n H T C Pd™
EW
N
®
!
Applications
Any application where a chain drive could be used.
S Y N C H R O N O U S
Can also be used with a backside idler when needed, allowing
for additional applications.
Suitable for high horsepower, low torque drives.
Key Features & Benefits
Part No: 8GTR-640-12
8
8mm Pitch Length
GTR Falcon HTC Belt
640
640mm Pitch
12mm Width
12
T h e S t a r O f O u r R e i n f o r c e d R u bb e r
Power Transmission Belt Portfolio
• Increased Horsepower Rating up to 30%
• Increased Continuous Operating Temperature up to 200ºF
• Static Conductive**
• Size for size convenience. Example:
8GTR-640-21 = Gates 8MGT-640-21*
• Reduced operating noise levels to comparable belt drives.
• Exceptional tensile strength for premium performance.
• Rubber construction provides better resistance to
flex fatigue.
3.6mm 5mm Pitch
• Versatility in a wide range of operating temperatures.
2.3mm
Falcon HTC is quickly setting the new standard in synchronous
drive system belting. When compared to conventional polyurethane
synchronous belts, the benefits of Falcon HTC become evident.
Specialty Compounded Materials
G i v e T h i s B e l t S u p e r i o r A d v a n t ag e s
A reinforced-rubber synchronous belt designed to work in a variety
of demanding drives, Falcon HTC now offers up to 30 percent more
horsepower over its predecessor. The ability to operate continuously
in temperatures up to 200ºF, along with being static conductive, helps
Falcon HTC perform in special applications, providing longer life and
higher output to meet your needs.
Lower Maintenance Costs
Reduce the Pain
Falcon HTC synchronous belts do not require lubrication often found
in chain drive applications. High-modulus cord members minimize the
need for retensioning normally required in standard v-belts, reducing
your overall maintenance cost.
Quiet Operation
Falcon HTC runs quieter, up to 6dB in operation for a better
environment while offering advanced flex-fatigue resistance to help
extend belt life.
Relative Belt Power Rating
Power Rating Comparison
140
Low Speed, 40rpm
Falcon PD®
20
Conditions: 14mm Pitch Belt, 20mm Width Belt, 32 Tooth Sprockets
16
5.8mm 8mm Pitch
(8mm Pitch)
Pitch Length (mm
640 9.8 mm
720
800
896
1000
1120
1200
Pitch Length (mm)
1280
14mm
1440 Pitch
1600
1792
2000
2240
2400
Pitch Length (mm)
2520
2840
3200
3600
4000
20mm
2.3mm
13.8mm 4480Pitch
3.6m
3mm
Pitch
Stock Widths: 12mm, 21mm, 36mm, 62mm
5.8mm 8
14 m
(14 mm Pitch)
9.8 mm
14mm Pitch
Pitch Length (mm
Pitch Length (mm)
Pitch Length (mm)
994
1120
1190
1260
1400
1568
1750
1890
1960
2100
2240
2380
2520
2660
2800
3136
3304
3500
3920
4410
Stock Widths: 20mm, 37mm, 68mm, 90mm, 125mm
Falcon HTC®
100
60
High Speed, 1750rpm
8m
3mm
Pitch
* Gates, Poly Chain and GT are trademarks of the Gates Corporation.
**Drive conditions and service variables in combination with time in operation
can result in a loss of static conductivity. It is recommended that a conductivity
check be added to drive preventive maintenance programs where belt static
conductivity is a requirement.
13.8mm
20
P
!
P O W E R
W
E
N
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S 2 0 1 0
F a l c o n H T C S p r o c k e ts
®
Applications
Any applications where a chain drive could be used or
there is a need for a high-efficiency drive system.
S Y N C H R O N O U S
For use where Falcon HTC belts are specified or desired.
System is backside idler compatible allowing for additional
applications.
Key Features & Benefits
Part No: GTR-22G-8M-12
GTR Falcon HTC Sprocket
22G 22 Grooves/Teeth
8M
8 mm Pitch Length
12
12 mm Width
Compact Drives With
High Performance
Falcon HTC sprockets are designed to be a part of a complete high
performance drive system. Working with our premium synchronous
Falcon HTC belts allows for a lot of performance in a small space,
giving you flexibility in design and application.
Falcon HTC belts and sprockets are ideal for use on a wide variety of
applications and industries.
Matching Belt To Sprocket
Is Simple
The part numbering system for Falcon HTC sprockets is simple and
easy. Just match the belt’s width and pitch length to that of the sprocket
and select the preferred number of grooves/teeth to provide the desired
performance characteristics. Refer to the part number example above
for a part number breakdown.
• Goodyear Engineered Products GTR-22G-8M-12
replaces 8MX-22S-12
• Convenient replacement for existing Poly Chain®
GT® 2 and Poly Chain GT Carbon®* drives
• Cast iron or steel construction
• Stock on most popular application sizes. Other sizes available as special order.
Quieter, More Flexible
Drive System
Falcon HTC belt and sprocket systems also offer a decrease in
operating noise. Tests show up to 6dB quieter operation than
comparable Poly Chain GT 2 and Poly Chain GT Carbon* belt
systems.
Proprietary rubber construction provides better resistance to flex
fatigue and versatility in a wide range of operating temperatures.
A System That Works With
Less Maintenance
Since Falcon HTC belts are made of our proprietary high-grade
rubber compound, you get a solution that can handle very
demanding synchronous drive systems. Falcon HTC does not
require lubrication. There is also no need for retensioning after the
initial run in period like V-belts drives. Install a Falcon HTC drive
system and watch your maintenance costs drop.
Get What You Pay For
With Falcon HTC belts and sprockets, you get more of what you pay
for with each energy dollar. This is especially true when Falcon HTC
is applied to high-energy consuming drives that are used 24 hours a
day, as well as high horsepower drives that inflate energy consumption
during peak periods.
* Gates, Poly Chain and GT are trademarks of the Gates Corporation.
17
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
Falcon HTC Sprockets
®
8M
S Y N C H R O N O U S
Part
Number
GTR-22G-8M-12
GTR-25G-8M-12
GTR-26G-8M-12
GTR-28G-8M-12
GTR-30G-8M-12
GTR-31G-8M-12
GTR-32G-8M-12
GTR-34G-8M-12
GTR-36G-8M-12
GTR-38G-8M-12
GTR-40G-8M-12
GTR-41G-8M-12
GTR-45G-8M-12
GTR-48G-8M-12
GTR-50G-8M-12
GTR-56G-8M-12
GTR-60G-8M-12
GTR-64G-8M-12
GTR-75G-8M-12
GTR-80G-8M-12
GTR-90G-8M-12
GTR-22G-8M-21
GTR-25G-8M-21
GTR-26G-8M-21
GTR-27G-8M-21
GTR-28G-8M-21
GTR-30G-8M-21
GTR-31G-8M-21
GTR-32G-8M-21
GTR-33G-8M-21
No. of
Teeth
22
25
26
28
30
31
32
34
36
38
40
41
45
48
50
56
60
64
75
80
90
22
25
26
27
28
30
31
32
33
Replaces
Sprocket
8MX-22S-12
8MX-25S-12
8MX-26S-12
8MX-28S-12
8MX-30S-12
8MX-31S-12
8MX-32S-12
8MX-34S-12
8MX-36S-12
8MX-38S-12
8MX-40S-12
8MX-41S-12
8MX-45S-12
8MX-48S-12
8MX-50S-12
8MX-56S-12
8MX-60S-12
8MX-75S-12
8MX-80S-12
8MX-90S-12
8MX-22S-21
8MX-25S-21
8MX-26S-21
8MX-27S-21
8MX-28S-21
8MX-30S-21
8MX-31S-21
8MX-32S-21
8MX-33S-21
Part
Number
No. of
Teeth
Replaces
Sprocket
Part
Number
No. of
Teeth
GTR-34G-8M-21
GTR-35G-8M-21
GTR-36G-8M-21
GTR-38G-8M-21
GTR-40G-8M-21
GTR-42G-8M-21
GTR-45G-8M-21
GTR-48G-8M-21
GTR-50G-8M-21
GTR-53G-8M-21
GTR-56G-8M-21
GTR-60G-8M-21
GTR-64G-8M-21
GTR-67G-8M-21
GTR-75G-8M-21
GTR-80G-8M-21
GTR-90G-8M-21
GTR-112G-8M-21
GTR-140G-8M-21
GTR-25G-8M-36*
GTR-28G-8M-36*
GTR-30G-8M-36
GTR-32G-8M-36
GTR-34G-8M-36
GTR-36G-8M-36
GTR-37G-8M-36
GTR-38G-8M-36
GTR-40G-8M-36
GTR-45G-8M-36
GTR-48G-8M-36
34
35
36
38
40
42
45
48
50
53
56
60
64
67
75
80
90
112
140
25
28
30
32
34
36
37
38
40
45
48
8MX-34S-21
8MX-35S-21
8MX-36S-21
8MX-38S-21
8MX-40S-21
8MX-42S-21
8MX-45S-21
8MX-48S-21
8MX-50S-21
8MX-53S-21
8MX-56S-21
8MX-60S-21
8MX-67S-21
8MX-75S-21
8MX-80S-21
8MX-90S-21
8MX-112S-21
8MX-140S-21
8MX-32S-36
8MX-34S-36
8MX-36S-36
8MX-37S-36
8MX-38S-36
8MX-40S-36
8MX-45S-36
8MX-48S-36
GTR-50G-8M-36
GTR-56G-8M-36
GTR-60G-8M-36
GTR-64G-8M-36
GTR-75G-8M-36
GTR-80G-8M-36
GTR-90G-8M-36
GTR-112G-8M-36
GTR-140G-8M-36
GTR-168G-8M-36+
GTR-192G-8M-36+
GTR-30G-8M-62
GTR-32G-8M-62
GTR-34G-8M-62
GTR-36G-8M-62
GTR-38G-8M-62
GTR-40G-8M-62
GTR-45G-8M-62
GTR-48G-8M-62
GTR-50G-8M-62
GTR-56G-8M-62
GTR-60G-8M-62
GTR-64G-8M-62
GTR-75G-8M-62
GTR-80G-8M-62
GTR-90G-8M-62
GTR-112G-8M-62
GTR-140G-8M-62
GTR-168G-8M-62+
GTR-192G-8M-62+
50
56
60
64
75
80
90
112
140
168
192
30
32
34
36
38
40
45
48
50
56
60
64
75
80
90
112
140
168
192
Replaces
Sprocket
8MX-50S-36
8MX-56S-36
8MX-60S-36
8MX-75S-36
8MX-80S-36
8MX-90S-36
8MX-112S-36
8MX-140S-36
8MX-34S-62
8MX-36S-62
8MX-38S-62
8MX-40S-62
8MX-45S-62
8MX-48S-62
8MX-50S-62
8MX-56S-62
8MX-60S-62
8MX-75S-62
8MX-80S-62
8MX-90S-62
8MX-112S-62
8MX-140S-62
--
14M
18
Part
Number
No. of
Teeth
Replaces
Sprocket
Part
Number
No. of
Teeth
Replaces
Sprocket
Part
Number
No. of
Teeth
Replaces
Sprocket
GTR-28G-14M-20
GTR-29G-14M-20
GTR-30G-14M-20˚
GTR-32G-14M-20˚
GTR-34G-14M-20˚
GTR-36G-14M-20˚
GTR-38G-14M-20
GTR-40G-14M-20
GTR-44G-14M-20
GTR-48G-14M-20
GTR-50G-14M-20
GTR-56G-14M-20
GTR-60G-14M-20
GTR-64G-14M-20
GTR-72G-14M-20
GTR-80G-14M-20
GTR-90G-14M-20
GTR-112G-14M-20
GTR-140G-14M-20
GTR-168G-14M-20
GTR-180G-14M-20+
GTR-200G-14M-20^
GTR-224G-14M-20^
GTR-28G-14M-37
GTR-29G-14M-37
GTR-30G-14M-37˚
GTR-32G-14M-37˚
GTR-34G-14M-37˚
GTR-36G-14M-37˚
GTR-38G-14M-37
GTR-40G-14M-37
GTR-40G-14M-37*
GTR-44G-14M-37
GTR-48G-14M-37
GTR-50G-14M-37
GTR-56G-14M-37
GTR-60G-14M-37
28
29
30
32
34
36
38
40
44
48
50
56
60
64
72
80
90
112
140
168
168
168
168
28
29
30
32
34
36
38
40
40
44
48
50
56
60
14MX-28S-20
14MX-29S-20
14MX-30S-20
14MX-32S-20
14MX-34S-20
14MX-36S-20
14MX-38S-20
14MX-40S-20
14MX-48S-20
14MX-50S-20
14MX-56S-20
14MX-60S-20
14MX-80S-20
14MX-90S-20
14MX-112-20
14MX-140S-20
14MX-168S-20
14MX-168S-20
14MX-168S-20
14MX-168S-20
14MX-28S-37
14MX-29S-37
14MX-30S-37
14MX-32S-37
14MX-34S-37
14MX-36S-37
14MX-38S-37
14MX-40S-37
14MX-40S-37
14MX-48S-37
14MX-50S-37
14MX-56S-37
14MX-60S-37
GTR-64G-14M-37
GTR-72G-14M-37
GTR-80G-14M-37
GTR-90G-14M-37
GTR-112G-14M-37
GTR-140G-14M-37
GTR-168G-14M-37+
GTR-180G-14M-37+
GTR-192G-14M-37+
GTR-200G-14M-37^
GTR-224G-14M-37^
GTR-28G-14M-68
GTR-29G-14M-68
GTR-30G-14M-68
GTR-32G-14M-68
GTR-34G-14M-68
GTR-36G-14M-68
GTR-38G-14M-68
GTR-40G-14M-68
GTR-44G-14M-68
GTR-48G-14M-68
GTR-50G-14M-68
GTR-56G-14M-68
GTR-60G-14M-68
GTR-64G-14M-68
GTR-72G-14M-68
GTR-80G-14M-68
GTR-90G-14M-68
GTR-112G-14M-68
GTR-140G-14M-68
GTR-168G-14M-68
GTR-180G-14M-68
GTR-192G-14M-68+
GTR-30G-14M-90*
GTR-32G-14M-90
GTR-34G-14M-90
GTR-36G-14M-90
64
72
80
90
112
140
168
180
192
200
168
28
29
30
32
34
36
38
40
44
48
50
56
60
64
72
80
90
112
140
168
180
192
30
32
34
36
14MX-80S-37
14MX-90S-37
14MX-112S-37
14MX-140S-37
14MX-168S-37
14MX-180S-37
14MX-200S-37
14MX-168S-20
14MX-29S-68
14MX-30S-68
14MX-32S-68
14MX-34S-68
14MX-36S-68
14MX-38S-68
14MX-40S-68
14MX-48S-68
14MX-50S-68
14MX-56S-68
14MX-60S-68
14MX-80S-68
14MX-90S-68
14MX-112S-68
14MX-140S-68
14MX-168S-68
14MX-180S-68
14MX-36S-90
GTR-38G-14M-90
GTR-40G-14M-90
GTR-44G-14M-90
GTR-48G-14M-90
GTR-50G-14M-90
GTR-56G-14M-90
GTR-60G-14M-90
GTR-64G-14M-90
GTR-72G-14M-90
GTR-80G-14M-90
GTR-90G-14M-90
GTR-112G-14M-90
GTR-140G-14M-90
GTR-168G-14M-90+
GTR-180G-14M-90+
GTR-192G-14M-90+
GTR-38G-14M-125
GTR-40G-14M-125
GTR-44G-14M-125
GTR-48G-14M-125
GTR-50G-14M-125
GTR-56G-14M-125
GTR-56G-14M-125*
GTR-60G-14M-125
GTR-64G-14M-125
GTR-72G-14M-125
GTR-80G-14M-125
GTR-90G-14M-125
GTR-112G-14M-125
GTR-140G-14M-125
GTR-168G-14M-125+
GTR-180G-14M-125
GTR-192G-14M-125+
38
40
44
48
50
56
60
64
72
80
90
112
140
168
180
192
38
40
44
48
50
56
56
60
64
72
80
90
112
140
168
180
192
14MX-38S-90
14MX-40S-90
14MX-48S-90
14MX-50S-90
14MX-56S-90
14MX-60S-90
14MX-80S-90
14MX-90S-90
14MX-112S-90
14MX-140S-90
14MX-168S-90
14MX-50S-125
14MX-56S-125
14MX-56S-125
14MX-60S-125
14MX-80S-125
14MX-90S-125
14MX-112S-125
14MX-140S-125
14MX-168S-125
14MX-180S-125
-
All Falcon HTC Sprockets use Taper-Lock Bushings.
* MPB
+ Inventories continue to evolve, contact Customer Service
for the latest stocking levels.
˚ Available with QD Bushing.
^
Special lightweight design, contact Veyance Technologies
to ensure suitability for your application
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
H a w k Pd™
®
Part No:
480
8M
20
Nearly every conceivable industrial drive application
where shaft synchronization is required. Hawk Pd belts
can also be used as an alternative to problem V-belt and
chain drives.
• Aggregate Machinery
• Office Equipment
• Paper Industry Machinery
• Machine Tool
• Printing Trade Machinery
• Home Appliances
• Food Processing Equipment • HVAC Units
• Packaging Machinery
• Textile Machinery
• Mining Equipment
• Farm Machinery
• Woodworking Machinery
• Vending Machines
480-8M-20
480mm Pitch Length
8mm Pitch
20mm Wide
Key Features & Benefits
A High-Performance Synchronous
Belt With a Universal Profile
With its universal tooth profile, Hawk Pd is precisely designed
and manufactured to fit the majority of existing high-capacity
synchronous applications. Hawk Pd can fulfill most existing drive
requirements in its class matching competitive offerings of belt
width and length.
Sprocket compatibility with Gates HTD*, Power Grip GT and
GT 2*, Carlisle RPP and RPP Plus*, and TB Wood’s Synchronous
QD*. Industry-compatible nomenclature for easy part number
interchange.
Belt Materials That Last Longer
Hawk Pd belts feature an enhanced rubber compound. This
compound is formulated to resist tooth deformity and increase
tooth rigidity, increasing belt life and decreasing replacement costs.
The demands of synchronous drives put additional strain
on the belt and tooth surface for high-speed and low-speed
applications. The Hawk Pd tooth profile resists ratcheting and
provides accurate positioning for synchronous drive applications.
Enhanced Goodyear Engineered Products materials and tooth
profile enable the teeth to engage the sprocket smoothly.
*Trademarks of the Gates Corporation, Carlisle, and TB Wood’s Incorporated respectively.
S Y N C H R O N O U S
A pp l i c a t i o n s
• Universal tooth profile drops into existing HTD,
GT and RPP sprockets. Industry-compatible
nomenclature.
• High-grade compounding.
• Requires little, if any, retensioning and less drive
maintenance.
• Oil, heat, ozone, and abrasion resistant.
• Designed for high-capacity performance.
• Higher horsepower rating than traditional
timing belts.
High Capacity Performance
Hawk Pd synchronous belts are designed for high-capacity
performance, exceeding the traditional speed limitations of chain
and performance limitations of belt drives. The new material
technology delivers a higher horsepower rating and improved life.
L o w e r M a i n t e n a n c e C os t s
Unlike chain drives, Hawk Pd belts and matching sprockets
do not require lubrication. There is also virtually no need for
retensioning like there is for V-belts and chain drives. Install
Hawk Pd and reduce your maintenance costs.
To learn more visit www.goodyearep.com/ptp.
19
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
H a w k Pd™
®
3.6mm 5mm Pitch
3m
2.3mm
Available Sizes
S Y N C H R O N O U S
Pitch Length (mm)
3mm
Pitch
5m
3.6mm 5mm Pitch
Pitch
Length (mm)
2.3mm
3mmPitch Length (mm) Pitch Length (mm)
Pitch Length (mm)
Pitch 635
1125
350
1195
670
375
1270
710
400
1420
740
425
5.7mm 8mm
Pitch
1595
800
450
1690
850
475
1790
890 5.7mm
500
*Nonstock, made to order. Minimum quantities required.
2.3mm
8mm
Pitch
1895
950
535
3.6mm 5mm Pitch
2000
1000
565
10.7 mm
1050
600
14mm Pitch
159*
204*
252*
264*
312*
612*
633*
675*
738*
2.3mm
3mm
Pitch
10.7 mm
*
13.8mm
8m
Available Sizes
5.7mm 8mm Pitch
1040
480
2.3mm 3mm
560
14mm Pitch 1120Pitch
1200
600
1280
640
1440
720
1600
800
1760
880
1800
960
13.8mm
2000
2400
2600
2800
3048
3280
3600
20mm
5.7mm
4400 8mm Pitch
Pitch
5.7mm
*
20mm
Pitch
Available13.8mm
Sizes
20mm
10.7 mm
14mm Pitch
Pitch
Pitch Length (mm) Pitch Length (mm) Pitch Length (mm)
966
1190
1400
1610
1778
1890
2100
2310
2450
2590
2800
3150
3360
3500
3850
4326
4578
4956
5320
5740
6160
6860
Stock Widths: 20mm, 30mm, 50mm, 85mm
Stock Widths: 40mm, 55mm, 85mm, 115mm, 170mm
*Static conductive
20 m
14mm Pitch
Available Sizes
3mm
Pitch
14mm Pitch
*Static conductive
10.7 mm
3
Stock Widths: 9mm, 15mm, 25mm
14 m
Pitch Length (mm) Pitch Length (mm) Pitch3.6mm
Length (mm)
5mm Pitch
0.7 mm
Available Sizes
*
13.8mm
20mm
Pitch
Pitch Length (mm) Pitch Length (mm) Pitch Length (mm)
2000
2500
3400
3800
4200
4600
5000
5200
5400
5800
6200
6600
Stock Widths: 115mm, 170mm, 230mm, 290mm, 340mm
*Static conductive
In addition to our stock lineup of synchronous belts, we can manufacture additional sizes (lengths) not listed.
For full product availability and specifications, please visit www.goodyearep.com/ptp
or contact a Goodyear Engineered Products sales representative.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check be added to drive
preventive maintenance programs where belt static conductivity is a requirement.
20
13.8mm
T R A N S M I S S I O N
Hawk
®
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
Synchronous Sprockets
Part No: P34
14
55
SK
P34-14M-55-SK
34 Grooves/Teeth
14mm Pitch Length
55mm Width
QD Bushing
S Y N C H R O N O U S
P O W E R
5mm Sprockets
Part No.
SAP No. Wt.*
Part No.
SAP No. Wt.*
Part No.
SAP No. Wt.*
P32-5M-15**
P32-5M-25**
P34-5M-15**
P34-5M-25**
P36-5M-15**
P36-5M-25**
P38-5M-15-JA
P38-5M-25-JA
P40-5M-15-JA
P40-5M-25-JA
P44-5M-15-JA
20182279
20182280
20182292
20182293
20182307
20182308
20182323
20182324
20182339
20182340
20182355
P44-5M-25-JA
P48-5M-15-JA
P48-5M-25-JA
P52-5M-15-JA
P52-5M-25-JA
P56-5M-15-SH
P56-5M-25-SH
P60-5M-15-SH
P60-5M-25-SH
P64-5M-15-SH
P64-5M-25-SH
20182356
20182371
20182372
20182388
20182389
20182400
20182401
20182417
20182418
20182429
20182430
P68-5M-15-SDS
P68-5M-25-SDS
P72-5M-15-SDS
P72-5M-25-SDS
P80-5M-15-SDS
P80-5M-25-SDS
P90-5M-15-SDS
P90-5M-25-SDS
P112-5M-15-SDS
P112-5M-25-SDS
20182446
20182447
20182458
20182459
20182475
20182476
20182492
20182493
20182192
20182193
** MPB
0.8
1.1
1.0
1.3
1.1
1.5
0.6
0.9
0.7
1.1
1.0
1.4
1.0
1.2
1.2
1.4
1.5
1.7
1.8
2.1
2.0
2.3
2.0
2.4
2.3
2.7
3.1
3.5
4.1
4.6
5.9
5.9
8mm Sprockets
Part No.
SAP No. Wt.*
Part No.
SAP No. Wt.*
Part No.
SAP No. Wt.*
P22-8M-20**
P22-8M-30**
P24-8M-20-JA
P24-8M-30-JA
P26-8M-20-JA
P26-8M-30-JA
P28-8M-20-QT
P28-8M-30-QT
P28-8M-50**
P30-8M-20-QT
P30-8M-30-QT
P30-8M-50**
P32-8M-20-QT
P32-8M-30-QT
P32-8M-50**
P34-8M-20-SH
P34-8M-30-SH
P34-8M-50-SH
P34-8M-85**
P36-8M-20-SH
P36-8M-30-SH
P36-8M-50-SH
20182242
20182243
20182244
20182245
20182247
20182248
20182256
20182257
20182258
20182270
20182271
20182272
20182281
20182282
20182283
20182294
20182295
20182296
20182298
20182309
20182310
20182311
P36-8M-85-SKL
P38-8M-20-SH
P38-8M-30-SH
P38-8M-50-SH
P38-8M-85-SKL
P40-8M-20-SH
P40-8M-30-SH
P40-8M-50-SH
P40-8M-85-SKL
P44-8M-20-SDS
P44-8M-30-SDS
P44-8M-50-SD
P44-8M-85-SFL
P48-8M-20-SDS
P48-8M-30-SDS
P48-8M-50-SD
P48-8M-85-SFL
P56-8M-20-SDS
P56-8M-30-SDS
P56-8M-50-SK
P56-8M-85-EL
P64-8M-20-SDS
20182313
20182325
20182326
20182327
20182329
20182341
20182342
20182343
20182345
20182357
20182358
20182359
20182361
20182373
20182374
20182375
20182377
20182402
20182403
20182404
20182405
20182431
P64-8M-30-SK
P64-8M-50-SK
P64-8M-85-SF
P72-8M-20-SDS
P72-8M-30-SK
P72-8M-50-SK
P72-8M-85-E
P80-8M-20-SDS
P80-8M-30-SK
P80-8M-50-SF
P80-8M-85-E
P90-8M-20-SDS
P90-8M-30-SK
P90-8M-50-SF
P90-8M-85-E
P112-8M-30-SK
P112-8M-50-SF
P112-8M-85-F
P144-8M-50-E
P144-8M-85-F
P192-8M-50-E
P192-8M-85-F
20182432
20182433
20182434
20182460
20182461
20182462
20182463
20182477
20182478
20182479
20182480
20182494
20182495
20182496
20182497
20182194
20182195
20182196
20182208
20182209
20182230
20182231
1.2
1.5
0.7
0.8
0.8
0.9
1.0
1.4
4.2
1.3
1.7
4.9
1.4
1.6
5.3
1.4
1.6
2.1
8.4
1.7
2.0
2.7
3.0
2.0
2.3
3.1
3.8
2.2
2.6
3.6
4.9
2.4
2.8
4.6
5.5
3.0
3.5
5.8
7.5
4.4
5.0
7.4
10.1
5.9
8.4
10.0
12.2
5.8
8.0
13.0
16.2
7.4
9.8
13.1
21.3
7.2
11.5
16.1
27.7
13.5
20.0
58.0
31.2
52.0
51.0
70.0
*Weight does not include bushing.
** MPB
21
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
14 m m S p r o c k e t s
Part No.
S Y N C H R O N O U S
P28-14M-40-SK
P28-14M-55-SK
P28-14M-85-SFL
P28-14M-115-SFL
P29-14M-40-SK
P29-14M-55-SK
P29-14M-85-SFL
P29-14M-115-SFL
P30-14M-40-SK
P30-14M-55-SK
P30-14M-85-EL
P30-14M-115-EL
P32-14M-40-SK
P32-14M-55-SK
P32-14M-85-EL
P32-14M-115-EL
P34-14M-40-SK
P34-14M-55-SK
P34-14M-85-EL
P34-14M-115-EL
P36-14M-40-SF
P36-14M-55-SF
P36-14M-85-SF
P36-14M-115-FL
P36-14M-170-FL
P38-14M-40-SF
P38-14M-55-SF
P38-14M-85-SF
P38-14M-115-FL
P38-14M-170-FL
P40-14M-40-SF
P40-14M-55-SF
P40-14M-85-SF
P40-14M-115-FL
P40-14M-170-FL
P44-14M-40-E
P44-14M-55-E
SAP No. Wt.*
20182252
20182253
20182254
20182250
20182260
20182261
20182262
20182259
20182266
20182267
20182268
20182264
20182275
20182276
20182277
20182273
20182286
20182287
20182288
20182284
20182302
20182303
20182304
20182299
20182301
20182317
20182318
20182319
20182314
20182316
20182333
20182334
20182335
20182330
20182332
20182349
20182350
*Weight does not include bushing.
22
5.2
6.5
8.8
11.3
5.9
7.5
10.1
13.0
5.6
6.7
7.8
10.0
7.2
8.7
10.7
13.7
8.6
10.5
13.6
17.3
7.7
10.6
13.9
17.0
23.0
10.3
12.2
16.1
21.0
28.0
12.1
14.4
19.1
25.0
34.0
14.8
16.9
Part No.
P44-14M-85-E
P44-14M-115-E
P44-14M-170-FL
P48-14M-40-E
P48-14M-55-E
P48-14M-85-E
P48-14M-115-E
P48-14M-170-FL
P52-14M-40-E
P52-14M-55-E
P52-14M-85-E
P52-14M-115-F
P52-14M-170-F
P56-14M-40-E
P56-14M-55-E
P56-14M-85-F
P56-14M-115-F
P56-14M-170-F
P60-14M-40-E
P60-14M-55-E
P60-14M-85-F
P60-14M-115-F
P60-14M-170-J
P64-14M-40-E
P64-14M-55-F
P64-14M-85-F
P64-14M-115-J
P64-14M-170-J
P68-14M-40-E
P68-14M-55-F
P68-14M-85-F
P68-14M-115-J
P68-14M-170-J
P72-14M-40-E
P72-14M-55-F
P72-14M-85-F
P72-14M-115-J
SAP No. Wt.*
20182351
20182346
20182348
20182365
20182366
20182367
20182362
20182364
20182380
20182381
20182382
20182378
20182379
20182392
20182393
20182394
20182390
20182391
20182409
20182410
20182411
20182407
20182408
20182421
20182422
20182423
20182419
20182420
20182438
20182439
20182440
20182436
20182437
20182450
20182451
20182452
20182448
21.0
25.2
39.0
19.0
21.9
27.6
33.2
51.0
23.1
26.3
32.6
43.4
54.2
27.7
31.1
44.4
51.3
63.0
32.5
36.4
52.4
60.2
76.0
28.8
52.2
60.4
73.0
87.0
31.1
37.0
53.7
84.8
99.3
29.9
47.6
58.2
96.7
Part No.
P72-14M-170-J
P80-14M-40-E
P80-14M-55-F
P80-14M-85-F
P80-14M-115-J
P80-14M-170-J
P90-14M-40-E
P90-14M-55-F
P90-14M-85-F
P90-14M-115-J
P90-14M-170-J
P112-14M-40-E
P112-14M-55-F
P112-14M-85-F
P112-14M-115-J
P112-14M-170-M
P144-14M-40-E
P144-14M-55-F
P144-14M-85-F
P144-14M-115-J
P144-14M-170-M
P168-14M-40-F
P168-14M-55-F
P168-14M-85-J
P168-14M-115-M
P168-14M-170-M
P192-14M-40-F
P192-14M-55-F
P192-14M-85-J
P192-14M-115-M
P192-14M-170-M
P216-14M-40-F
P216-14M-55-F
P216-14M-85-J
P216-14M-115-M
P216-14M-170-M
SAP No. Wt.*
20182449
20182467
20182468
20182469
20182465
20182466
20182484
20182485
20182486
20182482
20182483
20182184
20182185
20182186
20182182
20182183
20182200
20182201
20182202
20182198
20182199
20182212
20182213
20182214
20182210
20182211
20182222
20182223
20182224
20182220
20182221
20182234
20182235
20182236
20182233
20182234
112.2
34.2
51.5
60.6
84.8
103.9
34.4
47.7
58.1
73.3
88.2
45.0
61.8
78.8
100.5
158.0
72.2
95.9
107.9
143.5
233.5
92.9
99.8
133.0
215.0
258.6
114.0
122.8
162.0
256.0
337.0
147.0
158.0
224.0
304.0
405.0
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
20mm Sprockets
P72-20M-115-J
P72-20M-170-M
P72-20M-230-N
P72-20M-290-N
P72-20M-340-N
P80-20M-115-M
P80-20M-170-M
P80-20M-230-N
P80-20M-290-N
P80-20M-340-P
P90-20M-115-M
P90-20M-170-M
P90-20M-230-N
P90-20M-290-N
20182453
20182454
20182455
20182456
20182457
20182470
20182471
20182472
20182473
20182474
20182487
20182488
20182489
20182490
118.7
195.5
286.9
310.4
330.2
181.5
214.1
279.5
313.9
406.3
211.8
249.8
318.4
359.2
Part No.
P90-20M-340-P
P112-20M-115-M
P112-20M-170-N
P112-20M-230-N
P112-20M-290-P
P112-20M-340-P
P144-20M-115-N
P144-20M-170-N
P144-20M-230-P
P144-20M-290-P
P144-20M-340-W
P168-20M-115-N
P168-20M-170-P
SAP No. Wt.*
20182491
20182187
20182188
20182189
20182190
20182191
20182203
20182204
20182205
20182206
20182207
20182215
20182216
425.4
238.5
308.9
356.8
513.2
542.9
340.5
426.2
542.0
637.2
813.4
417.2
560.0
Part No.
P168-20M-230-P
P168-20M-290-W
P168-20M-340-W
P192-20M-115-N
P192-20M-170-P
P192-20M-230-W
P192-20M-290-W
P192-20M-340-S
P216-20M-115-N
P216-20M-170-P
P216-20M-230-W
P216-20M-290-W
P216-20M-340-S
SAP No. Wt.*
20182217
20182218
20182219
20182225
20182226
20182227
20182228
20182229
20182237
20182238
20182239
20182240
20182241
635.0
891.2
947.2
499.9
680.0
935.1
1060.3
1367.8
565.7
812.9
1061.5
1238.9
1554.9
S Y N C H R O N O U S
SAP No. Wt.*
Part No.
8 m m P itc h T a p e r - L o c k
Synchronous Sprockets
Part No.
SAP No. Wt.*
Part No.
SAP No. Wt.*
Part No.
SAP No. Wt.*
P22-8M-20-1108
P22-8M-30-1108
P24-8M-20-1108
P24-8M-30-1108
P26-8M-20-1108
P26-8M-30-1108
P28-8M-20-1108
P28-8M-30-1108
P28-8M-50-1108
P30-8M-20-1210
P30-8M-30-1210
P30-8M-50-1210
P32-8M-20-1210
P32-8M-30-1210
P32-8M-50-1210
P34-8M-20-1610
P34-8M-30-1610
P34-8M-50-1610
P34-8M-85-1615
P36-8M-20-1610
P36-8M-30-1610
20182754
20182755
20182756
20182757
20182758
20182759
20182763
20182764
20182765
20182773
20182774
20182775
20182780
20182781
20182782
20182787
20182788
20182789
20182790
20182795
20182796
P36-8M-50-1610
P36-8M-85-1615
P38-8M-20-1610
P38-8M-30-1610
P38-8M-50-1610
P38-8M-85-1610
P40-8M-20-1610
P40-8M-30-2012
P40-8M-50-2012
P40-8M-85-2012
P44-8M-20-2012
P44-8M-30-2012
P44-8M-50-2012
P44-8M-85-2012
P48-8M-20-2012
P48-8M-30-2012
P48-8M-50-2012
P48-8M-85-2012
P56-8M-20-2012
P56-8M-30-2012
P56-8M-50-2517
20182797
20182798
20182803
20182804
20182805
20182806
20182811
20182812
20182813
20182814
20182819
20182820
20182821
20182822
20182827
20182828
20182829
20182830
20182839
20182840
20182841
P56-8M-85-2517
P64-8M-20-2012
P64-8M-30-2517
P64-8M-50-2517
P64-8M-85-2517
P72-8M-20-2012
P72-8M-30-2517
P72-8M-50-2517
P72-8M-85-3020
P80-8M-20-2517
P80-8M-30-2517
P80-8M-50-2517
P80-8M-85-3020
P90-8M-20-2517
P90-8M-30-2517
P90-8M-50-3020
P90-8M-85-3020
P112-8M-30-2517
P112-8M-50-3020
P112-8M-85-3020
20182842
20182851
20182852
20182853
20182854
20182863
20182864
20182865
20182866
20182871
20182872
20182873
20182874
20182879
20182880
20182881
20182882
20182751
20182752
20182753
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.2
1.6
1.0
1.2
1.7
1.3
1.5
2.0
1.2
1.4
1.9
2.9
1.5
1.7
2.4
3.8
1.8
2.1
2.8
3.8
2.1
2.1
2.9
4.0
2.6
3.0
3.9
5.4
3.5
3.9
5.2
7.2
5.4
6.1
7.6
9.8
7.6
9.2
11.2
13.8
10.0
12.4
15.1
17.3
13.2
16.1
26.0
23.0
12.2
13.4
26.0
30.0
28.0
27.0
35.0
*Weight does not include bushing.
23
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
14 m m P itc h T a p e r - L o c k
Synchronous Sprockets
Part No.
S Y N C H R O N O U S
P28-14M-40-2012
P28-14M-55-2012
P28-14M-85-2012
P29-14M-40-2012
P29-14M-55-2012
P29-14M-85-2012
P30-14M-40-2012
P30-14M-55-2517
P30-14M-85-2517
P30-14M-115-2517
P32-14M-40-2012
P32-14M-55-2517
P32-14M-85-2517
P32-14M-115-2517
P34-14M-40-2012
P34-14M-55-2517
P34-14M-85-2517
P34-14M-115-2517
P36-14M-40-2517
P36-14M-55-2517
P36-14M-85-3020
P36-14M-115-3020
P38-14M-40-2517
P38-14M-55-2517
P38-14M-85-3020
SAP No. Wt.*
20182760
20182761
20182762
20182766
20182767
20182768
20182770
20182771
20182772
20182769
20182777
20182778
20182779
20182776
20182784
20182785
20182786
20182783
20182792
20182793
20182794
20182791
20182800
20182801
20182802
*Weight does not include bushing.
24
5.2
6.4
9.0
5.9
7.4
10.3
5.8
6.5
8.7
11.0
7.4
8.5
11.6
14.8
8.7
10.3
14.1
17.8
9.7
11.2
12.3
15.4
11.5
13.4
15.4
Part No.
P38-14M-115-3020
P40-14M-40-2517
P40-14M-55-2517
P40-14M-85-3020
P40-14M-115-3020
P44-14M-40-2517
P44-14M-55-2517
P44-14M-85-3020
P44-14M-115-3535
P48-14M-40-2517
P48-14M-55-3020
P48-14M-85-3020
P48-14M-115-3535
P52-14M-40-2517
P52-14M-55-3020
P52-14M-85-3535
P52-14M-115-4040
P56-14M-40-2517
P56-14M-55-3020
P56-14M-85-3535
P56-14M-115-4040
P60-14M-40-3020
P60-14M-55-3020
P60-14M-85-3535
P60-14M-115-4040
SAP No. Wt.*
20182799
20182808
20182809
20182810
20182807
20182816
20182817
20182818
20182815
20182824
20182825
20182826
20182823
20182832
20182833
20182834
20182831
20182836
20182837
20182838
20182835
20182844
20182845
20182846
20182843
19.2
13.3
15.6
18.5
23.0
16.6
18.7
22.0
28.0
21.0
23.0
29.0
38.0
26.0
28.0
41.0
45.0
21.0
34.0
51.0
56.0
27.0
40.0
61.0
68.0
Part No.
P64-14M-40-3020
P64-14M-55-3020
P64-14M-85-3535
P64-14M-115-4545
P68-14M-40-3020
P68-14M-55-3020
P68-14M-85-3535
P68-14M-115-4545
P72-14M-40-3020
P72-14M-55-3020
P72-14M-85-3535
P72-14M-115-4545
P80-14M-40-3020
P80-14M-55-3020
P80-14M-85-3535
P80-14M-115-4545
P90-14M-40-3020
P90-14M-55-3020
P90-14M-85-3535
P90-14M-115-4545
P112-14M-40-3020
P112-14M-55-3020
P112-14M-85-3535
P112-14M-115-4545
SAP No. Wt.*
20182848
20182849
20182850
20182847
20182856
20182857
20182858
20182855
20182860
20182861
20182862
20182859
20182868
20182869
20182870
20182867
20182876
20182877
20182878
20182875
20182748
20182749
20182750
20182747
29.0
34.0
71.0
80.0
31.0
37.0
83.0
94.0
34.0
41.0
70.0
109.0
35.0
43.0
74.0
143.0
36.0
40.0
72.0
127.0
47.0
55.0
89.0
136.0
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
B l a c k h a w k Pd™
®
A pp l i c a t i o n s
A High-Performance Synchronous
Belt With a Universal Profile
For a curvilinear belt that offers improved performance in your
synchronous application, look no further than Blackhawk Pd. The high-performance belt offers best-of-breed technology and
higher horsepower for the money. Its proven durability and
strength makes it a compatible upgrade for many other timing
belts.
Belt Materials That Last Longer
Blackhawk Pd belts feature a patented high-grade rubber
compound. This cross-linked elastomer is formulated to resist
tooth deformity and increase tooth rigidity, increasing belt life and
decreasing replacement costs.
Blackhawk Pd’s Flexten® tensile members provide excellent
dimensional stability and high impact strength. Blackhawk Pd
requires virtually no retensioning and minimum maintenance.
The demands of synchronous drives put additional strain on the
belt and tooth surface for high-speed and low-speed applications.
The Blackhawk Pd tooth profile resists ratcheting and provides
accurate positioning for synchronous drive applications.
S Y N C H R O N O U S
Part No: 480 8M BH 12
480 480mm Pitch Length
8M 8mm Pitch
BH Blackhawk Belt
12 12mm Wide
Nearly every conceivable industrial drive application
where precise shaft synchronization is required.
Blackhawk Pd belts can also be used as an alternative to
problem V-belt and chain drives.
• Aggregate Machinery
• Office Equipment
• Paper Industry Machinery
• Machine Tool
• Printing Trade Machinery
• Home Appliances
• Food Processing Equipment • HVAC Units
• Packaging Machinery
• Textile Machinery
• Mining Equipment
• Farm Machinery
• Woodworking Machinery
• Vending Machines
Key Features & Benefits
•Universal tooth profile drops into existing HTD and RPP sprockets.
•High-grade Hibrex compound.
•Flexten tensile members provide excellent
dimensional stability and high-impact strength.
•Requires little, if any, retensioning and less drive
maintenance.
•Oil, heat, ozone, and abrasion resistant.
•Designed for high-capacity performance.
•Higher horsepower rating than traditional
timing belts.
•Static conductive*
L o w e r M a i n t e n a n c e C os t s
Unlike chain drives, Blackhawk Pd belts and matching
sprockets do not require lubrication. There is virtually no need
for retensioning like there is for V-belt and chain drives. Install
Blackhawk Pd and watch your maintenance costs drop to
practically nothing.
High Capacity Performance
Blackhawk Pd synchronous belts are designed for high-capacity
performance, exceeding the traditional speed limitations of chain
and performance limitations of belt drives. Blackhawk Pd belts
are able to perform in drives ranging from fractional horsepower
to 400 horsepower. The new material technology delivers a
higher horsepower rating.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check be added to drive
preventive maintenance programs where belt static conductivity is a requirement.
To learn more visit www.goodyearep.com/ptp.
25
P O W E R
2.3mm
T R A N S M I S S I O N
3.6mm 5mm Pitch
P R O D U C T S 2.3mm
S Y N C H R O N
O U S 3mm
Pitch
B l a c k h a w k Pd™
®
3mm
Pitch
5.7mm 8mm Pitch
5.7mm 8mm Pitch
S Y N C H R O N O U S
m
3.6mm 5mm Pitch
8m
14mm Pitch
Available Sizes
Pitch Length (mm)
480
560
600
640
720
13.8mm
800
880
960
1040
1120
1200
1280
Pitch Length (mm)
1440
1600
1760
1800
20mm 2000
Pitch 2400
2600
2800
3048
3280
3600
4400
Stock Widths: 12mm, 22mm, 35mm, 60mm
10.7 mm
14m
14mm Pitch
Available Sizes
Pitch Length (mm)
Pitch Length13.8mm
(mm)
966
1190
1400
1610
1778
1890
2100
2310
2450
2590
2800
3150
3360
3500
3850
4326
4578
4956
5320
5740
6160
6860
Stock Widths: 20mm, 42mm, 65mm, 90mm, 120mm
In addition to our stock lineup of synchronous belts, we can manufacture additional sizes (lengths) not listed.
For full product availability and specifications, please visit www.goodyearep.com/ptp or
contact a Goodyear Engineered Products sales representative.
26
20mm
Pitch
T R A N S M I S S I O N
B lackhawk
P R O D U C T S ®
S Y N C H R O N O U S
2 0 1 0
S ynchronous S prockets
Part No: W38
14
20
SF
W38-14M-20-SF
38 Grooves/Teeth
14 mm Pitch Length
20 mm Width
QD Bushing
S Y N C H R O N O U S
P O W E R
8mm Synchronous
Blackhawk Sprockets
Part No.
SAP No. Wt.*
Part No.
SAP No. Wt.*
Part No.
SAP No. Wt.*
W22-8M-12**
W22-8M-22**
W22-8M-35**
W22-8M-60**
W24-8M-12-JA
W24-8M-22-JA
W24-8M-35**
W24-8M-60**
W26-8M-12-JA
W26-8M-22-JA
W26-8M-35**
W26-8M-60**
W28-8M-12-QT
W28-8M-22-QT
W28-8M-35-QT
W28-8M-60**
W30-8M-12-QT
W30-8M-22-QT
W30-8M-35-QT
W30-8M-60**
W32-8M-12-QT
W32-8M-22-QT
W32-8M-35-QT
W32-8M-60**
W34-8M-12-SH
W34-8M-22-SH
W34-8M-35-SH
20182589
20182590
20182591
20182592
20182593
20182594
20182595
20182596
20182597
20182598
20182599
20182600
20182606
20182607
20182608
20182609
20182620
20182621
20182622
20182623
20182629
20182630
20182631
20182632
20182638
20182639
20182640
W34-8M-60**
W36-8M-12-SH
W36-8M-22-SH
W36-8M-35-SH
W36-8M-60-SKL
W38-8M-12-SH
W38-8M-22-SH
W38-8M-35-SH
W38-8M-60-SKL
W40-8M-12-SH
W40-8M-22-SH
W40-8M-35-SH
W40-8M-60-SKL
W44-8M-12-SDS
W44-8M-22-SDS
W44-8M-35-SD
W44-8M-60-SFL
W48-8M-12-SDS
W48-8M-22-SDS
W48-8M-35-SD
W48-8M-60-SFL
W56-8M-12-SDS
W56-8M-22-SDS
W56-8M-35-SK
W56-8M-60-EL
W64-8M-12-SDS
W64-8M-22-SDS
20182641
20182647
20182648
20182649
20182650
20182656
20182657
20182658
20182659
20182665
20182666
20182667
20182668
20182674
20182675
20182676
20182677
20182683
20182684
20182685
20182686
20182697
20182698
20182699
20182700
20182711
20182712
W64-8M-35-SK
W64-8M-60-SF
W72-8M-12-SDS
W72-8M-22-SDS
W72-8M-35-SK
W72-8M-60-E
W80-8M-12-SDS
W80-8M-22-SDS
W80-8M-35-SF
W80-8M-60-E
W90-8M-12-SDS
W90-8M-22-SDS
W90-8M-35-SF
W90-8M-60-E
W112-8M-12-SK
W112-8M-22-SK
W112-8M-35-SF
W112-8M-60-F
W144-8M-12-SK
W144-8M-22-SK
W144-8M-35-E
W144-8M-60-F
W192-8M-12-SF
W192-8M-22-SF
W192-8M-35-E
W192-8M-60-F
20182713
20182714
20182725
20182726
20182727
20182728
20182734
20182735
20182736
20182737
20182743
20182744
20182745
20182746
20182557
20182558
20182559
20182560
20182566
20182567
20182568
20182569
20182580
20182581
20182582
20182583
0.9
1.2
1.6
2.3
0.5
0.7
2.0
2.7
0.6
0.7
2.4
3.3
0.7
1.1
1.5
4.0
0.9
1.3
1.8
4.8
1.1
1.4
1.6
5.7
1.2
1.3
1.6
6.6
1.3
1.6
2.0
2.4
1.6
1.9
2.3
3.0
1.9
2.3
2.8
3.8
2.1
2.5
3.8
4.4
2.6
3.2
4.9
6.1
3.9
4.5
6.2
8.4
5.3
6.1
8.8
10.2
5.1
6.0
11.6
14.0
6.7
7.8
11.3
18.5
6.3
7.5
14.0
24.5
10.6
12.0
17.2
53.3
18.5
20.7
27.5
45.3
27.5
30.6
46.2
62.0
*Weight does not include bushing.
**MPB
27
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
14 m m S y n c h r o n o u s
Blackhawk Sprockets
S Y N C H R O N O U S
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
W28-14M-20-SK
W28-14M-42-SK
W28-14M-65-SFL
W28-14M-90**
W28-14M-120**
W29-14M-20-SK
W29-14M-42-SK
W29-14M-65-SFL
W29-14M-90**
W29-14M-120**
W30-14M-20-SK
W30-14M-42-SK
W30-14M-65-EL
W30-14M-90-EL
W30-14M-120-EL
W32-14M-20-SK
W32-14M-42-SK
W32-14M-65-EL
W32-14M-90-EL
W32-14M-120-EL
W34-14M-20-SK
W34-14M-42-SF
W34-14M-65-EL
W34-14M-90-EL
W34-14M-120-FL
W36-14M-20-SF
W36-14M-42-SF
W36-14M-65-FL
W36-14M-90-FL
W36-14M-120-FL
W38-14M-20-SF
W38-14M-42-SF
W38-14M-65-FL
W38-14M-90-FL
W38-14M-120-FL
W40-14M-20-SF
W40-14M-42-SF
W40-14M-65-FL
W40-14M-90-FL
20182602
20182603
20182604
20182605
20182601
20182611
20182612
20182613
20182614
20182610
20182616
20182617
20182618
20182619
20182615
20182625
20182626
20182627
20182628
20182624
20182634
20182635
20182636
20182637
20182633
20182643
20182644
20182645
20182646
20182642
20182652
20182653
20182654
20182655
20182651
20182661
20182662
20182663
20182664
3.2
5.1
6.7
18.9
21.0
3.6
6.2
7.2
20.2
22.0
4.0
5.5
5.7
7.4
9.2
4.9
7.0
7.6
10.0
12.8
5.8
7.4
10.0
13.2
14.4
6.4
8.5
11.4
13.8
17.0
7.5
10.2
14.1
17.4
21.5
8.6
11.9
17.8
21.6
W40-14M-120-FL
W44-14M-20-E
W44-14M-42-E
W44-14M-65-E
W44-14M-90-FL
W44-14M-120-FL
W48-14M-20-E
W48-14M-42-E
W48-14M-65-E
W48-14M-90-FL
W48-14M-120-FL
W52-14M-20-E
W52-14M-42-E
W52-14M-65-E
W52-14M-90-F
W52-14M-120-F
W56-14M-20-E
W56-14M-42-E
W56-14M-65-F
W56-14M-90-F
W56-14M-120-F
W60-14M-20-E
W60-14M-42-E
W60-14M-65-F
W60-14M-90-F
W60-14M-120-F
W64-14M-20-E
W64-14M-42-E
W64-14M-65-F
W64-14M-90-F
W64-14M-120-J
W68-14M-20-E
W68-14M-42-E
W68-14M-65-F
W68-14M-90-F
W68-14M-120-J
W72-14M-20-E
W72-14M-42-E
20182660
20182670
20182671
20182672
20182673
20182669
20182679
20182680
20182681
20182682
20182678
20182688
20182689
20182690
20182691
20182687
20182693
20182694
20182695
20182696
20182692
20182702
20182703
20182704
20182705
20182701
20182707
20182708
20182709
20182710
20182706
20182716
20182717
20182718
20182719
20182715
20182721
20182722
31.9
12.0
14.6
17.7
27.0
31.9
14.7
18.8
23.0
36.0
41.3
17.6
23.0
28.0
37.0
43.0
21.0
27.4
39.0
44.0
51.1
25.2
32.2
46.0
53.0
59.8
23.0
28.0
53.7
60.1
73.0
25.2
31.2
46.8
55.0
84.0
24.4
30.2
W72-14M-65-F
W72-14M-90-F
W72-14M-120-J
W80-14M-20-E
W80-14M-42-E
W80-14M-65-F
W80-14M-90-J
W80-14M-120-J
W90-14M-20-E
W90-14M-42-F
W90-14M-65-F
W90-14M-90-J
W90-14M-120-M
W112-14M-20-E
W112-14M-42-F
W112-14M-65-J
W112-14M-90-J
W112-14M-120-M
W144-14M-20-E
W144-14M-42-F
W144-14M-65-M
W144-14M-90-M
W144-14M-120-M
W168-14M-20-F
W168-14M-42-F
W168-14M-65-M
W168-14M-90-M
W168-14M-120-M
W192-14M-20-J
W192-14M-42-J
W192-14M-65-M
W192-14M-90-M
W192-14M-120-N
W216-14M-20-J
W216-14M-42-J
W216-14M-65-M
W216-14M-90-M
W216-14M-120-N
20182723
20182724
20182720
20182730
20182731
20182732
20182733
20182729
20182739
20182740
20182741
20182742
20182738
20182553
20182554
20182555
20182556
20182552
20182562
20182563
20182564
20182565
20182561
20182571
20182572
20182573
20182574
20182570
20182576
20182577
20182578
20182579
20182575
20182585
20182586
20182587
20182588
20182584
51.1
61.6
96.0
28.0
34.0
53.0
74.7
84.0
29.4
43.6
52.3
67.0
149.0
39.1
76.9
82.6
90.6
147.0
63.3
111.0
189.0
199.0
214.0
131.0
138.0
196.0
235.0
273.0
146.0
157.0
264.0
279.0
365.0
171.0
186.0
303.0
377.0
423.0
*Weight does not include bushing.
**MPB
28
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
P o s iti v e D r i v e P d ™
®
Part No: 100 XL 025
100
10.0˝ Pitch Length
XL
Pitch-Trapezoidal Tooth Profile
025
.25˝ Wide
Speed, Accuracy & Dependability
for Precision-Engineered Drives
Goodyear Engineered Products Positive Drive belts give you the
opportunity to design your drives for the speed, accuracy, and
dependability consistent with the best synchronous belt drives, all
without the bulk, weight, and added cost that is inherent in chain
and gear power transmission systems.
Goodyear Engineered Products Pd belts have precision-molded
teeth to deliver the synchronized power you need. Because they’re
made of specially compounded rubber, reinforced with highstrength, stable fiberglass tensile cord members, and have a longwearing nylon facing, they are durable and provide a smooth,
precise operation.
Nearly every conceivable industrial drive application
where precise shaft synchronization is required. Positive
Drive belts can also be used as an alternative to problem
V-belt and chain drives.
• Aggregate Machinery
• Office Equipment
• Chain Drives
• Machine Tools
• Packaging Machinery
• Farm Machinery • Paper Industry Machinery
• Home Appliances
• Food Processing Equipment • Textile Machinery
• Printing Trade Machinery
• Mining Equipment
• Woodworking Machinery
Key Features & Benefits
S Y N C H R O N O U S
A pp l i c a t i o n s
• Universal trapezoidal tooth profiles drop into
existing sprockets.
• High-grade compounding.
• Fiberglass tension cords for excellent resistance
to shrinkage/elongation.
• Oil, heat, ozone, and abrasion resistant.
• Low-maintenance/high-efficiency rating.
Engineered for Full-Power
T r a n s m i ss i o n , S m oo t h O p e r a t i o n
Our Positive Drive belts are made with world-class rubber
technology which is specifically compounded to resist damaging
environmental factors that can shorten belt life. Our specialized
compound technology has excellent oil, heat, and ozone
resistance, increasing durability and preserving belt flexibility
leading to extended belt life.
Available
in a
Variety
of
Pitches
Goodyear Engineered Products Pd belts are available in a variety of
pitches depending on the application.
29
P O W E R
T R A N S M I S S I O N
P 0.045"
R O D U C T S S0.045"
Y N C H R O N O U S
0.17"
P o s iti v e D r i v e P d ™
0.045"
S Y N C H R O N O U S
MXL
0.500"
Pitch
0.080"
Pitch
(Mini Extra Light)
0.09"
0.14"
For small business machines, office
equipment, electric equipment, etc.
0.200"
0.375"
Pitch
13⁄16˝Pitch
Pitch
Standard Part Numbers
40mxl 0.44"
72mxl
112mxl
44mxl
80mxl
120mxl
48mxl
88mxl
140mxl
0.875"
64mxl
96mxl
168mxl
Pitch
Stock Widths*
0.62"
0.09"
0.17"
1⁄8 inch = 012
3⁄16 inch = 019
1⁄4 inch = 025 1.250"
Pitch
0.200"
Pitch
XL
0.14"
0.375" 0.200"
Pitch Pitch
0.375"
Pitch
0.44"
0.44"
For business machines, instruments,
sound equipment, etc.
0.875"
Pitch
1⁄5˝ Pitch
Standard Part Numbers
190xl
200xl
210xl
220xl
230xl
240xl
250xl
260xl
280xl
290xl
300xl
310xl
330xl
340xl
0.62"
350xl
370xl
380xl
1.250"
390xl
Pitch
400xl
420xl
450xl
0.17"
460xl
480xl
0.500"
500xl
Pitch
570xl
630xl
770xl
0.14"
L
(Light)
For fraction power-rated motor applications0.875"
such as in-home appliances,
small tools,
Pitchpumps, blowers, etc.
3⁄8˝ Pitch
0.045"
0.17"
Standard Part Numbers
450l
255l
124l
0.500"
480l
270l
135l
0.080"
1.250"
Pitch
510l
285l
150l
Pitch
Pitch
540l
300l
165l
600l
322l
187l
0.14"
0.09"
660l
345l
195l
817l
367l
210l
900l
390l
225l
240l 0.200" 420l
0.375"
Pitch
Stock Widths* 1⁄2 inch = 050 Pitch
3⁄4 inch = 075
0.44"
1 inch = 100
Stock Widths* 1⁄4 inch = 025
0.200"3⁄8 inch = 037 0.375"
Pitch
Pitch
45"
0.17"
0.500"
Pitch
0.080"
Pitch
0.14"
(Heavy)
For machine tools, pumps, fans, presses, motor generator sets, etc.
0.200"
Pitch
44"
0.375"
1⁄2˝ Pitch
Pitch
Standard Part Numbers
210h
220h
230h
0.875"
240h
Pitch
270h
300h
320h
330h
360h
390h
1.250"
400h
Pitch
410h
420h
Stock Widths*
30
450h
480h
490h
510h
540h
560h
570h
585h
600h
630h
645h
660h
700h
3⁄4
**
0.62"
0.875"
Pitch
H
.09"
0.875"
Pitch
**
0.44"
730h
750h
780h
800h
820h
850h
900h
960h
1000h
1100h
1250h
1400h
1700h
inch = 075
1 inch = 100
11⁄2 inch = 150
2 inches = 200 3 inches = 300
XH
XXH
(Extra Heavy)
0.62"
For medium torque applications on
heavy industrial equipment.
1.250"
7⁄ 8˝ Pitch
Pitch
Standard Part Numbers
507xh
560xh
630xh
700xh
770xh
840xh
980xh
1120xh
Stock Widths* 2 inches = 200
3 inches = 300
4 inches = 400
0.500"
Pitch
0.14"
0.09"
(Extra Light)
50xl 0.62"
60xl
70xl
80xl
90xl
100xl
110xl
0.045"
120xl
130xl
140xl
0.080"
150xl
160xlPitch
170xl
0.09"
180xl
®
0.500"
0.080"
Pitch
Pitch
0.080"
Pitch
0.17"
1260xh
1400xh
1540xh
1750xh
1.250"
Pitch
(Double Extra Heavy)
For high torque applications on heavy
industrial equipment.
11⁄4˝ Pitch
Standard Part Numbers
700xxh
800xxh
900xxh
Stock Widths*
1000xxh
1200xxh
1400xxh
1600xxh
1800xxh
2 inches = 200
3 inches = 300
4 inches = 400
5 inches = 500
13.00˝ wide Pd sleeves are available from stock in XL, L, H, XH and XXH profiles.
Please consult your PTP List Prices Pages publications for the full range of sizes.
*Stock Widths: Use the three-digit size number as a suffix to the belt number when ordering.
Note: For nonstock sizes, contact your local Goodyear Engineered Products PTP industrial distributor.
**Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity.
It is recommended that a conductivity check be added to drive preventive maintenance programs where belt static
conductivity is a requirement.
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S P ositive D rive
®
Part No: 20
L
050
JA
2 0 1 0
S prockets
20L050-JA
20 Teeth
Pitch-Trapezoidal Tooth Profile
0.50 Width
Bushing
S Y N C H R O N O U S
P O W E R
XL S y n c h r o n o u s
(Timing) Sprockets
Part No.
SAP No.
Wt.*
10XL037**
11XL037**
12XL037**
14XL037**
15XL037**
16XL037**
18XL037**
20XL037**
20178894
20178895
20181888
20181896
20181901
20181909
20181927
20181950
0.03
0.03
0.06
0.06
0.09
0.09
0.13
0.19
^Aluminum
** MPB
Part No.
21XL037**
22XL037**
24XL037**
28XL037**
30XL037**
32XL037**^
36XL037**^
SAP No.
Wt.*
Part No.
20181963
20181974
20181990
20182022
20182035
20182041
20182060
0.19
0.22
0.25
0.34
0.41
0.22
0.30
40XL037**^
42XL037**^
44XL037**^
48XL037**^
60XL037**^
72XL037**^
32XL037**
SAP No.
Wt.*
20182075
20182091
20182094
20182104
20182119
20182134
20395679
0.31
0.31
0.31
0.38
0.38
0.50
0.20
L Synchronous
(Timing) Sprockets
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
10L050**
12L050**
12L075**
14L050**
14L075**
14L100**
16L050**
16L075**
16L100**
17L050**
17L075**
17L100**
18L050-JA
18L075-JA
18L100-JA
19L050**
19L075**
19L100**
20L050-JA
20L075-JA
20L100-JA
21L050**
21L075**
21L100**
20178893
20181886
20181887
20181893
20181894
20181895
20181906
20181907
20181908
20181910
20181911
20181912
20181917
20181918
20181919
20181936
20181937
20181938
20181944
20181945
20181946
20181960
20181961
20181962
0.2
0.3
0.4
0.5
0.6
0.7
0.7
0.8
1.0
0.8
1.0
1.1
0.4
0.5
0.6
1.0
1.2
1.4
0.6
0.7
0.9
1.3
1.5
1.8
22L050-JA
22L075-JA
22L100-JA
24L050-SH
24L075-SH
24L100-SH
26L050**
26L050-SH
26L075-SH
26L100-SH
28L050-SH
28L075-SH
28L100-SH
30L050-SDS
30L075-SDS
30L100-SDS
32L050-SDS
32L075-SDS
32L100-SDS
36L050-SDS
36L075-SDS
36L100-SDS
40L050-SDS
20181968
20181969
20181970
20181984
20181985
20181986
20182000
20182001
20182002
20182003
20182016
20182017
20182018
20182029
20182030
20182031
20182047
20182048
20182049
20182065
20182066
20182067
20182080
0.8
0.8
0.9
0.5
0.7
0.9
2.3
0.9
1.1
1.2
1.1
1.3
1.6
1.2
1.5
1.8
1.5
1.7
1.9
2.0
2.3
2.6
2.6
40L075-SDS
40L100-SDS
44L050-SDS
44L075-SDS
44L100-SDS
48L050-SDS
48L075-SDS
48L100-SDS
60L050-SD
60L075-SD
60L100-SD
72L050-SD
72L075-SD
72L100-SD
84L050-SD
84L075-SD
84L100-SD
96L050-SD
96L075-SD
96L100-SD
120L050-SD
120L075-SD
120L100-SD
20182081
20182082
20182099
20182100
20182101
20182109
20182110
20182111
20182124
20182125
20182126
20182139
20182140
20182141
20182153
20182154
20182155
20182167
20182168
20182169
20181880
20181881
20181882
3.0
3.4
3.1
3.5
3.9
4.2
4.6
5.1
5.6
6.1
6.7
6.7
7.6
7.5
7.9
8.7
9.6
9.6
10.6
11.6
12.5
13.7
15.0
*Weight does not include bushing.
** MPB
31
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
H Synchronous
(Timing) Sprockets
S Y N C H R O N O U S
Part No.
SAP No.
Wt.*
14H100**
14H100-JA
14H150-JA
14H200-JA
16H100-JA
16H150-JA
16H200-JA
16H300**
18H100-SH
18H150-SH
18H200-SH
18H300**
19H100**
19H150**
19H200**
19H300**
20H100**
20H100-SH
20H150-SH
20H200-SH
20H300**
21H100-SH
21H150**
21H200**
21H300**
22H100-SDS
22H150-SD
22H200-SD
22H300-SD
23H100-SDS
24H100-SDS
24H150-SD
24H200-SD
24H300-SD
25H100-SDS
20181889
20181890
20181891
20181892
20181902
20181903
20181904
20181905
20181913
20181914
20181915
20181916
20181932
20181933
20181934
20181935
20181939
20181940
20181941
20181942
20181943
20181956
20181957
20181958
20181959
20181964
20181965
20181966
20181967
20181979
20181980
20181981
20181982
20181983
20181995
1.4
0.7
1.0
1.2
0.8
0.8
1.3
4.1
1.0
1.4
1.7
5.4
3.0
3.7
4.6
6.2
3.4
1.4
1.8
2.2
7.0
1.5
4.8
5.6
7.5
1.5
2.2
2.7
3.6
1.7
1.9
2.8
3.3
4.3
2.1
*Weight does not include bushing.
** MPB
32
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
26H100-SDS
26H150-SD
26H200-SD
26H300-SD
27H100-SDS
28H100-SDS
28H150-SD
28H200-SD
28H300-SD
29H100-SDS
30H100-SD
30H150-SD
30H200-SD
30H300-SD
31H100-SD
32H100-SK
32H150-SK
32H200-SK
32H300-SK
33H100-SK
34H100-SK
35H100-SK
36H100-SK
36H150-SK
36H200-SK
36H300-SK
37H100-SK
38H100-SK
39H100-SK
40H100-SK
40H150-SK
40H200-SK
40H300-SK
41H100-SK
42H100-SK
20181996
20181997
20181998
20181999
20182011
20182012
20182013
20182014
20182015
20182023
20182025
20182026
20182027
20182028
20182040
20182043
20182044
20182045
20182046
20182053
20182054
20182059
20182061
20182062
20182063
20182064
20182071
20182073
20182074
20182076
20182077
20182078
20182079
20182090
20182092
2.4
3.6
3.9
4.7
2.7
3.0
4.5
5.1
6.4
3.3
4.6
5.3
6.0
7.6
4.9
4.1
5.2
5.8
7.6
5.0
5.4
5.9
5.8
6.6
7.6
9.6
6.8
7.3
7.8
8.4
9.1
10.2
12.3
8.9
9.4
43H100-SK
44H100-SK
44H150-SK
44H200-SK
44H300-SK
45H100-SK
46H100-SK
48H100-SK
48H150-SK
48H200-SF
48H300-SF
60H100-SF
60H150-SF
60H200-SF
60H300-SF
72H100-SF
72H150-SF
72H200-SF
72H300-SF
84H100-SF
84H150-SF
84H200-SF
84H300-SF
96H100-SF
96H150-SF
96H200-E
96H300-E
120H100-SF
120H150-SF
120H200-E
120H300-E
156H100-SF
156H150-SF
156H200-E
156H300-E
20182093
20182095
20182096
20182097
20182098
20182102
20182103
20182105
20182106
20182107
20182108
20182120
20182121
20182122
20182123
20182135
20182136
20182137
20182138
20182149
20182150
20182151
20182152
20182163
20182164
20182165
20182166
20178896
20178897
20178898
20178899
20181897
20181898
20181899
20181900
10.0
9.9
10.8
12.1
14.7
11.2
11.8
9.1
10.5
14.0
16.9
11.1
12.8
15.9
20.0
16.9
18.9
19.9
24.0
21.0
23.0
27.0
32.0
25.0
28.0
35.0
42.0
31.0
36.0
47.0
55.0
45.8
52.0
68.0
79.0
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
18XH200-SK
18XH300-SK
18XH400**
20XH200-SK
20XH300-SK
20XH400-SK
22XH200-SK
22XH300-SK
22XH400-SK
24XH200-SF
24XH300-SF
24XH400-SF
26XH200-SF
26XH300-SF
26XH400-SF
28XH200-E
28XH300-E
28XH400-E
20181920
20181921
20181925
20181947
20181948
20181949
20181971
20181972
20181973
20181987
20181988
20181989
20182004
20182005
20182006
20182019
20182020
20182021
6.8
9.4
19.2
7.9
10.2
12.5
10.7
13.9
16.5
12.3
16.0
19.2
14.7
16.7
22.7
16.9
20.0
23.9
30XH200-E
30XH300-E
30XH400-E
32XH200-E
32XH300-E
32XH400-E
36XH200-E
36XH300-E
36XH400-E
40XH200-F
40XH300-F
40XH400-F
48XH200-F
48XH300-F
48XH400-J
60XH200-F
60XH300-F
60XH400-J
20182032
20182033
20182034
20182050
20182051
20182052
20182068
20182069
20182070
20182083
20182084
20182085
20182112
20182113
20182114
20182127
20182128
20182129
20.8
25.6
30.0
24.0
30.0
35.0
27.0
33.0
39.0
40.0
52.7
57.8
49.0
57.0
65.0
48.0
59.9
78.0
72XH200-F
72XH300-J
72XH400-J
84XH200-F
84XH300-J
84XH400-J
96XH200-F
96XH300-J
96XH400-J
120XH200-F
120XH300-J
120XH400-J
20182142
20182143
20182144
20182156
20182157
20182158
20182170
20182171
20182172
20181883
20181884
20181885
59.7
78.8
93.0
68.7
92.0
107.0
83.7
106.0
129.8
107.9
142.9
165.5
Part No.
SAP No.
Wt.*
48XXH200-J
48XXH300-J
48XXH400-J
48XXH500-M
60XXH200-J
60XXH300-J
60XXH400-M
60XXH500-M
72XXH200-J
72XXH300-J
72XXH400-M
72XXH500-M
90XXH200-J
90XXH300-J
90XXH400-M
90XXH500-M
20182115
20182116
20182117
20182118
20182130
20182131
20182132
20182133
20182145
20182146
20182147
20182148
20182159
20182160
20182161
20182162
73.0
90.0
104.0
154.0
93.0
112.0
169.0
195.0
111.0
142.0
224.0
231.9
140.9
192.8
259.0
314.0
S Y N C H R O N O U S
XH S y n c h r o n o u s
(Timing) Sprockets
** MPB
XXH S y n c h r o n o u s
(Timing) Sprockets
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
18XXH200-SK
18XXH300-SF
18XXH400-SF
18XXH500**
20XXH200-SK
20XXH300-SF
20XXH400-SF
20XXH500**
22XXH200-E
22XXH300-E
22XXH400-E
22XXH500-E
24XXH200-E
24XXH300-E
24XXH400-E
24XXH500-F
20181928
20181929
20181930
20181931
20181951
20181952
20181953
20181954
20181975
20181976
20181977
20181978
20181991
20181992
20181993
20181994
16.1
19.6
24.0
48.6
19.8
25.2
31.1
61.0
23.8
30.0
36.2
42.5
29.5
36.9
44.4
56.0
26XXH200-E
26XXH300-E
26XXH400-F
26XXH500-F
30XXH200-F
30XXH300-F
30XXH400-F
30XXH500-J
34XXH200-F
34XXH300-F
34XXH400-J
34XXH500-J
40XXH200-F
40XXH300-F
40XXH400-J
40XXH500-J
20182007
20182008
20182009
20182010
20182036
20182037
20182038
20182039
20182055
20182056
20182057
20182058
20182086
20182087
20182088
20182089
35.1
43.3
57.2
61.0
48.0
64.6
67.0
93.0
57.0
68.0
86.0
97.0
60.0
75.8
96.0
110.0
*Weight does not include bushing.
** MPB
33
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
L Taper-Lock
Timing Sprockets
S Y N C H R O N O U S
Part No.
SAP No.
Wt.*
TL18L050 1008
TL18L075 1008
TL18L100 1008
TL20L050 1008
TL20L075 1008
TL20L100 1008
TL22L050 1008
TL22L075 1008
20182508
20182509
20182510
20182515
20182516
20182517
20182522
20182523
0.5
0.5
0.7
0.7
0.7
1.0
0.9
0.9
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
TL22L100 1008
TL24L050 1210
TL24L075 1210
TL24L100 1210
TL26L050 1210
TL26L075 1210
TL26L100 1210
TL28L050 1210
20182524
20182529
20182530
20182531
20182536
20182537
20182538
20182543
1.3
1.0
1.0
1.3
1.2
1.2
1.7
1.2
TL28L075 1610
TL28L100 1610
TL30L050 1610
TL30L075 1610
TL30L100 1610
TL32L050 1610
TL32L075 1610
TL32L100 1610
20182544
20182545
20182546
20182547
20182548
20182549
20182550
20182551
1.2
1.7
1.5
1.5
2.2
1.9
1.9
2.7
H Taper-Lock
Timing Sprockets
Part No.
SAP No.
Wt.*
TL14H100 1008
TL14H150 1008
TL16H100 1008
TL16H150 1008
TL16H200 1008
TL18H100 1210
TL18H150 1215
TL18H200 1215
TL18H300 1215
TL20H100 1210
20182499
20182500
20182501
20182502
20182503
20182504
20182505
20182506
20182507
20182511
0.8
1.0
1.3
1.5
1.9
1.2
1.7
1.9
2.7
1.7
*Weight does not include bushing.
34
Part No.
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
TL20H150 1215
TL20H200 1215
TL20H300 1215
TL22H100 1610
TL22H150 1615
TL22H200 1615
TL22H300 1615
TL24H100 1610
TL24H150 2012
TL24H200 2012
20182512
20182513
20182514
20182518
20182519
20182520
20182521
20182525
20182526
20182527
2.3
2.7
4.0
1.8
2.7
3.0
4.2
1.8
2.4
2.8
TL24H300 2012
TL26H100 2012
TL26H150 2012
TL26H200 2012
TL26H300 2012
TL28H100 2012
TL28H150 2012
TL28H200 2012
TL28H300 2012
20182528
20182532
20182533
20182534
20182535
20182539
20182540
20182541
20182542
4.5
2.4
3.4
3.8
5.6
3.0
4.3
5.3
7.0
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
S u p e r T o r q u e Pd™
®
Part No: 100S4.5M175
100
10mm Width
S
Super Torque Positive Drive Belt
4.5M 4.5mm Pitch – Modified Round Tooth Profile
175
175mm Pitch Length
Nearly every conceivable industrial drive application
where precise shaft synchronization is required. Super
Torque Pd belts can also be used as an alternative to
problem V-belt and chain drives.
• Milling Machines
•Conveyors
•Engine Accessory Drives
•Debarkers
•Internal Combustion Engines •Lathes •Timers or Controllers
•Shapers
•Compressors
•Textile Machinery
•Wood Chippers
•Mixers
Key Features & Benefits
Built For Strength & Endurance
Super Torque Pd belts are designed for high-capacity performance.
They are also made of the highest quality materials.
The tensile members are made from high-strength, stable
fiberglass. They have excellent flex life and are resistant to
elongation. The backing is made of our proprietary compound
technology that is highly heat-resistant and shear-resistant. And
the nylon facing is fabricated to provide low friction interface
between belt and sprocket.
S Y N C H R O N O U S
A pp l i c a t i o n s
•Unique tooth profile for quiet tooth engagement.
•Improved horsepower capacity over standard
HTD profiles.
• High-grade compound.
•Fiberglass tension cords for excellent resistance
to shrinkage/elongation.
•Oil, heat, ozone, and abrasion resistant.
•Mating sprockets required.
•Low-maintenance/high-efficiency rating.
A D i f f e r e n t P os i t i v e D r i v e
T oo t h D e s i g n
Goodyear Engineered Products Super Torque Pd belt tooth carries
some significant advantages over competitive synchronous belts.
You can run your finger along the bottom of the tooth and feel
the flat surface. When the belt engages the uniquely designed pulley
profile, forces are distributed throughout the entire belt tooth to
disperse critical stresses over more area, resulting in reduced tooth
shear and longer life.
The pulley for our Super Torque Pd belt has an arch in the
bottom of the grooves that projects up to support the belt tooth.
This support from the pulley is the key dynamic feature to
increased belt capabilities. Together, the pulley and tooth of the
Super Torque Pd belt extend the possibilities at both ends of the
design spectrum.
All Super Torque Pd belts are nonstock. Standard factory lead times will apply.
Minimums apply. Contact your local Goodyear Engineered Products PTP
industrial distributor.
To learn more visit www.goodyearep.com/ptp.
35
m
m
m
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S S u p e r T o r q u e Pd™
®
s3m
3mm
Pitch
1.9mm
S Y N C H R O N O U S
mm
P O W E R
3mm
2.8mm
5.3mm
8mm
2.8mm
4.5mm
8mm
Pitch
4.5mm
Pitch
Pitch
Part
Number
Part
Number
Pitch
14mm
14mm
Pitch
Pitch
s8m
Part
Number
S8M440
S8M448
8mm
5.3mm
S8M480
Pitch
S8M496
3.4mm 5mm
S8M512
Pitch
S8M528
S8M560
S8M576
S8M592
S8M600
S8M632
14mm
S8M648
10.2mm
Pitch
S8M656
S8M680
3mm
2.8mm 4.5mm
S8M688
Pitch
Pitch
S8M712
S8M720
S8M752
S8M760
S8M800
8mm
3.4mm
5mm
Pitch
s 1 4 m*
10.2mm
14mm
Pitch
No.
of Teeth
S3M252
S3M264
S3M276
S3M300
S3M339
84
88
92
100
113
Part
Number
Part
Number
No.
of Teeth
S3M501
S3M537
S3M564
S3M633
167
179
188
211
No.
of Teeth
Part
Number
No.
of Teeth
S4.5M306
S4.5M342
68
76
S4.5M504
S4.5M621
112
138
Part
Number
No.
of Teeth
Part
Number
No.
of Teeth
S5M700
S5M750
S5M800
S5M850
S5M900
S5M950
S5M1000
S5M1050
S5M1125
140
150
160
170
180
190
200
210
225
S5M1270
S5M1350
S5M1420
S5M1800
S5M2000
S5M2770
254
270
284
360
400
554
Part
Number
No.
of Teeth
Part
Number
No.
of Teeth
S8M1120
S8M1136
S8M1160
S8M1176
S8M1184
S8M1200
S8M1208
S8M1224
S8M1248
S8M1256
S8M1264
S8M1280
S8M1304
S8M1312
S8M1360
S8M1384
S8M1400
S8M1432
S8M1440
S8M1480
140
142
145
147
148
150
151
153
156
157
158
160
163
164
170
173
175
179
180
185
S8M1488
S8M1544
S8M1552
S8M1600
S8M1680
S8M1696
S8M1760
S8M1800
S8M2000
S8M2032
S8M2240
S8M2272
S8M2392
S8M2400
S8M2496
S8M2600
S8M2800
S8M3200
186
193
194
200
210
212
220
225
250
254
280
284
299
300
312
325
350
400
Part
Number
No.
of Teeth
Part
Number
No.
of Teeth
S14M2310
S14M2450
S14M2590
S14M2800
S14M3150
165
175
185
200
225
S14M3500
S14M3850
S14M4004
S14M4508
S14M5012
250
275
286
322
358
Part
Number
No.
of Teeth
S3M363
S3M384
S3M420
S3M459
S3M486
121
128
140
153
162
No.
of Teeth
Part
Number
55
66
Part
Number
No.
of Teeth
S5M475
S5M500
S5M525
S5M560
S5M575
S5M600
S5M625
S5M650
S5M675
95
100
105
112
115
120
125
130
135
Part
Number
No.
of Teeth
S8M824
S8M840
S8M848
S8M880
S8M896
S8M920
S8M928
S8M936
S8M944
S8M960
S8M976
S8M984
S8M992
S8M1000
S8M1024
S8M1032
S8M1040
S8M1056
S8M1072
S8M1096
103
105
106
110
112
115
116
117
118
120
122
123
124
125
128
129
130
132
134
137
Part
Number
No.
of Teeth
S14M1778
S14M1890
S14M2002
S14M2100
S14M2240
127
135
143
150
160
S4.5M247
S4.5M297
No.
of Teeth
S5M255
S5M295
3.4mm 5mm
14mm
S5M325
3.4mm 5mm
10.2mm S5M350
Pitch
Pitch
Pitch
S5M375
S5M400
S5M425
S5M435
1.9mm 3mm
4.5mm
2.8mm
S5M450
Pitch
Part
Number
Pitch
Pitch
5.3mm
No.
of Teeth
S4.5M175
39
S4.5M180
40
3.4mm
S4.5M225
5mm 50
s5m
10.2mm
10.2mm
1.9mm
No.
of Teeth
S3M120
40
S3M150
50
2.8mm
S3M1774.5mm59
S3M201 Pitch 67
S3M225
75
s4.5m
Pitch
3mm
Pitch
8mm
Pitch
Pitch
Part
Number
51
59
65
70
75
80
85
87
90
No.
of Teeth
55
56
60
62
64
66
70
72
74
75
79
81
82
85
86
89
90
94
95
100
Part
Number
No.
of Teeth
S14M1120
S14M1190
S14M1400
S14M1540
S14M1610
80
85
100
110
115
*Static conductive
Note: All Super Torque Pd belts are nonstock. Standard factory lead times will apply. Mandrel quantity minimums apply. Other sizes available upon request.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check be added to drive
preventive maintenance programs where belt static conductivity is a requirement.
36
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
D u a l H i - P e r f o r m a n c e Pd
& D u a l P o s iti v e D r i v e
®
A pp l i c a t i o n s
D u a l H i - P e r f o r m a n c e Pd
Part No: D10408M20
D
Dual Sided
1040 1040 mm Pitch Length
8M
8mm Pitch – Round Tooth Profile
20
20mm Wide
S Y N C H R O N O U S
For precision drives where synchronized reverse rotation
drive shafts are encountered and compactness is desired.
Key Features & Benefits
•Dual-sided teeth versatility in 8M, 14M, XL,
L, and H profiles.
• High-grade compounding.
•Fiberglass tension cords for excellent resistance to shrinkage/elongation.
•More compact drive designs.
•Oil, heat, ozone, and abrasion resistant.
D u a l P os i t i v e D r i v e B e l t s —
XL , L , & H P r o f i l e s
D u a l P o s iti v e D r i v e
Part No: D225L050
D
Dual Sided
225
22.5˝ Pitch Length
L
L Pitch – Trapezoidal Tooth Profile
050
.50˝ Wide
Improved Efficiency With Dual
Synchronous Belts
Goodyear Engineered Products dual synchronous belts have
precision teeth on both sides. This allows the design of more
sophisticated, more efficient, and more compact drives where a
single belt is needed to provide accurate timing from either side,
rotation direction changes, or both.
Since a Dual Hi-Performance Pd or Dual Positive Drive belt can
replace two or more single-sided synchronous belts, less space is
needed. This reduction in space means smaller sprockets can be
used, bringing the weight and component cost of the drive system
down considerably, contributing to a more efficient drive system.
Goodyear Engineered Products Dual Positive Drive belts drop into
existing trapezoidal profiled sprockets.
High-Strength Tension Cords
The tension-carrying member in Dual HPPD and Dual Positive
Drive belts is twisted from multiple strands of fiberglass cord which
are high in tensile strength, flex life, and resistance to elongation.
A d v a n c e d C o m po u n d
Technology For Long Life
Our dual synchronous belts are made with specialized compound
technology designed to resist damaging environmental factors that
can shorten belt life. This compound technology has excellent
oil, heat, ozone, and abrasion resistance, increasing durability and
preserving belt flexibility leading to extended belt life.
Dual Hi-Performance Pd Belts—
8M & 14M Profiles
Dual Hi-Performance Pd belts, with their unique round tooth
profile, drop into corresponding HTD sprockets. They were
designed to minimize interference between belt and sprocket
during mesh, providing greater horsepower capacity without
slippage or speed variation. By designing the tooth to disperse
critical stresses and create a positive engagement with the
sprocket, belt performance is improved along with assuring longer
belt life.
To learn more visit www.goodyearep.com/ptp.
37
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S D u a l H i - P e r f o r m a n c e Pd
& D u a l P o s iti v e D r i v e
®
S Y N C H R O N O U S
Dual
H i -P e r f o r m a n c e Pd
D u a l P o s iti v e D r i v e
0.120"
XL
8m
Part
Number
8mm
No. of
Teeth
D720 8M
90
100
D800 8M
D880 8M
110
D960 8M
14.6mm120
D1040 8M
130
D1120 8M
140
150
D1200 8M
D1280 8M
160
180
D1440 8M
D1600 8M
200
D1760 8M
220
225
D1800 8M
8mm
14m
14.6mm
8mm
Pitch
Part
Number
No. of
Teeth
D2000 8M
D2400 8M
D2600 8M
14mm
D2800 8M
Pitch 8M
D3048
D3280 8M
D3600 8M
D4400 8M
250
300
325
350
381
410
450
550
0.200" Pitch
(Extra Light)
XL
D60XL
1⁄5 inch pitch
0.180"
D70XL
D80XL
For business machines,
D90XL
D100XL
instruments, sound
D110XL
equipment, etc.
D120XL
0.234"D130XL
D140XL
D150XL
0.120"
D160XL
3
Stock Widths* 1⁄4 0.200"
inch=025,
Pitch⁄8 inch=037
0.180"
Available in 20, 30, 50 &
85 mm widths.
8mm
Pitch
Part Numbers
D290XL
D170XL
D300XL
D180XL
D310XL
D190XL
D330XL
D200XL 0.375"
D362XL
D210XL Pitch
D392XL
D220XL
D450XL
D230XL
D492XL
D240XL
D690XL
D250XL
0.500"
D900XL
D260XL
D280XL Pitch
0.375"
Pitch
L
(Light)
L Part Numbers
D420L
D270L
D124L
3⁄8 inch pitch
0.234"
D450L
D285L
D150L
0.120"
D480L
D300L 0.500"
D187L
For fraction power-rated
D510L
D322L Pitch
D210L
0.200" Pitch
motor applications such
D540L
D345L
D225L
as in-home appliances,
D600L
D367L
D240L
D660L
D390L
D255L
small tools, pumps, etc.
0.180"
14mm
Pitch
3⁄4 inch=075, 1 inch=100
Stock Widths* 1⁄2 inch=050,0.375"
Pitch
Part
Number
No. of
Teeth
Part
Number
No. of
Teeth
D1400 14M
D1610 14M
D1778 14M
D1890 14M
D2100 14M
D2450 14M
D3150 14M
D3500 14M
100
115
127
135
150
175
225
250
D3850 14M
D4326 14M
D4578 14M
D6160 14M
275
309
327
440
Available in 40, 55, 85 &
115 mm widths.
0.234"
H
1⁄2
0.500"
Pitch
(Heavy)
inch pitch
For machine tools,
pumps, fans, presses,
motor generator sets, etc.
D240H
D270H
D300H
D330H
D360H
D390H
D420H
D450H
D480H
H Part Numbers
D800H
D510H
D850H
D540H
D900H
D560H
D1000H
D570H
D1100H
D600H
D1250H
D630H
D1400H
D660H
D1700H
D700H
D750H
Stock Widths* 3⁄4 inch=075, 1 inch=100,
11⁄2 inch=150, 2 inches=200, 3 inches=300
*Stock Widths: Use the three-digit size number as a suffix to the belt number
when ordering. For nonstock sizes, contact your local Goodyear PTP
industrial distributor.
Note: Other sizes available upon request.
38
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S 2 0 1 0
Open End Pd™
®
For synchronized applications.
• Elevation Mechanisms
• Positioning Drives
• Linear Motion Drives
• Metering Drives
• Open/Close Mechanisms
• Conveying Drives
•Reciprocating Drives
• Reversing Drives
•Replaces Chain Applications • Fixed Center Drives
•Synchronized Tracking
Key Features & Benefits
•Wide load range available from various cross sections.
•High power-to-weight ratio allows for lighter
metallic or nonmetallic pulleys for greater weight
savings.
•Provides space-saving design opportunities using
small pulleys, short centers, and narrow belts.
•Smooth engagement of belt and pulley eliminates
chatter and vibration.
•Low noise improves aesthetic acceptance of
equipment.
•Requires no lubrication or retensioning.
Part No: XL 075
XL
Pitch-Trapezoidal Tooth
075
0.75˝ Wide
Your Choice for Speed,
Accuracy & Dependability
In power transmission or synchronization applications such as
conveying, linear motion, or positioning, Goodyear Engineered
Products Open End Pd belts are the economical and trouble-free
drive solution.
S Y N C H R O N O U S
A pp l i c a t i o n s
Economy is derived from the Open End Pd belt’s reduced bulk
weight and lower costs compared to chain drives. Precision-molded
teeth efficiently deliver the required power while running smoother
and quieter than chain drives. They require less maintenance, as
well as provide more design options.
Goodyear Engineered Products Open End Pd belts are available
in Hawk Pd®, Falcon HTC®, Positive Drive Pd®, Super Torque
Pd® and Metric T Pd® constructions. Regardless of the application,
the entire product line is designed to provide increased belt life,
reduced overall costs, and lower noise generation. In short, Open
End Pd synchronous belts give you the power to drive your designs
better than ever.
2.3mm
3.6mm 5mm Pitch
2.3mm
Hawk Pd
3.6mm 5mm
To learn more visit www.goodyearep.com/ptp.
3mm
Pitch
3mm
Pitch
5.7mm 8mm Pitch
(Round Tooth)
3.6mm 5mm Pitch
2.3mm
3mm
Pitch
3.6mm 5mm Pitch
32.3mm
m
Part No.
5m
3mm
Pitch
Roll Length Roll Length
10.7 mm
(ft)
(m)
13.8mm
8m
87
8M10
285
189
112
66
8M20
8M25
8M30
8M40
8M50
8M75
14M25
14M40
14M55
14M85
14M115
20mm
Pitch
20mm
Pitch
633
420
312
246
13.8mm
203
151
92
193
128
95
20mm
75
Pitch
62
46
28
14mm Pitch
14 m
Part No.
5.7mm
58 8mm Pitch 8M15
13.8mm
10.7 mm
Roll Length Roll Length
Part
No.
(ft)
(m)
14mm
Pitch
5.7mm 8mm Pitch
3M06
285
3M09
190
5M06
935
10.7 mm
5M09
620
14mm
Pitch
5M15
367
10.7 mm5M25
217
14mm Pitch
5.7mm 8mm Pitch
Roll Length Roll Length
(ft)
(m) 13.8mm
56
308
184
128
75
49
20mm
Pitch
17
94
56
39
23
15
39
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O0.045"
U S
P R O D U C T S Open End Pd
®
0.045"
0.045"
Positive Drive
0.080"
0.17"0.09"
0.045"
0.080"
Pitch
Pitch
(Trapezoidal
Tooth)
0.14"
0.09"
0.14"
0.09"
0.500"
Pitch
0.500"
Pitch
0.500"
Pitch
0.080"
Pitch
™
0.17"
0.17"
0.17"
0.200"
Pitch
0.14" 0.045"
0.375"
Pitch
0.17"
0.44"
0.500"
Pitch
S Y N C H R O N O U S
0.080"
Pitch
mxl*
0.14"
0.09"
0.200"
Pitch
0.200"
Pitch
0.375"
Pitch
0.375"
Pitch
x l0.44"
0.500"
Pitch
0.080"
Pitch
l 0.09"
0.44"
0.14"
h
Roll Length Roll Length
0.200"
(ft)
(m)
0.375"
Part No.
XL037
L050
0.44"
L075
L100
551
361
0.44"
266
170
H200
H300
Pitch
711
516
338
249
0.875"
Pitch
0.62"
Pitch
217
157
0.62"
103
76
Pitch
H050
H075
H100
H150
1.250"
1.250"
Pitch
Pitch
168
110
81
0.875" 52
xh*
0.62"
Roll Length Roll Length 0.875" 0.875"
0.200"
Part No.
(ft) 0.375" (m)
Pitch No.
Pitch Part
Roll Length Roll Length
(ft)
1.250" (m)
123
75
Pitch
37
23
2.3mm
Pitch
Pitch
* MXL and XH profiles available as special order
only. 5mm
Standard
factory lead times will apply. Minimums apply.
3.6mm
Pitch
Contact your local Goodyear Power Transmission Products Distributor.
0.62"
2.3mm
5.8mm 8mm Pitch
(8 mm Pitch)
Part Number
10.7 mm
8GTR-12
8GTR-21
8GTR-36
8GTR-62
Roll Length (ft)
243
135
1.9mm
72
3mm
Pitch
13.8mm
Super Torque Pd®
90S3M
100S3M
60S45M
100S45M
60S5M
100S5M
289
88
240
73 10.2mm
3.4mm 5mm
5mm
3.4mm
157
48
Pitch
Pitch
144
44
236
72
141
43
1050
320
627
191
Metric T Pd®
Part No.
6T5
7T5
10T5
15T10
3mm
2.8mm
Part Number
Roll Length (ft)
Roll Length (m)
14GTR-20
253
14GTR-37
128
14GTR-68 5.3mm 628mm
1.9mm
77
39
19
Pitch
3.4mm
2.8mm 4.5mm
Pitch
3mm
Pitch
4.5mm
14mm
Pitch
Pitch
13.8mm
5mm
Pitch
3.4mm
5mm
Pitch
5.3mm
s5m
Part No.
8mm
Pitch
s8m
Roll Length Roll Length
(ft)
(m)
150S5M14mm
250S5MPitch
100S8M
150S8M
175S8M
200S8M
250S8M
300S8M
413
246
633
420
358
312
246
203
126
75
193
128
109
95
75
62
10.2mm
3.4mm 5mm
Pitch
Part No.
14mm
Pitch
s 14 m
Roll Length Roll Length
(ft)
(m)
350S8M
174
400S8M
151
250S14M 14mm
225
10.2mm
400S14M Pitch135
500S14M
104
600S14M
85
53
46
69
41
32
26
14mm
14mm
Pitch
Pitch
(Trapezoidal Tooth)
Roll Length Roll Length
(ft)
(m)
217
187
131
266
1.9mm
10.7 mm
(14 mm Pitch) Pitch
(Round Tooth)
s4.5m
10.2mm
10.2mm
4.5mm
Pitch
20mm
Pitch
Roll Length Roll Length
(ft)
(m)
8mm
5.3mm
50S3M
8mm
5.3mm
Pitch
60S3M
Pitch
133
74
41
2.8mm
22
8mm
5.3mm
Pitch
4.5mm
2.8mm
2.8mm 4.5mm
Pitch
Pitch
s3m
Part No.
5.7mm 8mm P
14m
Roll Length (m)
436
14mm Pitch
3mm
1.9mm 3mm
1.9mm
Pitch
Pitch
3mm
Pitch
1.250"
Pitch
1.250"
Pitch
8m
3.6mm 5
0.62"
3mm
Pitch
Falcon HTC®
40
0.875"
Pitch
66
57
40
81
Part No.
16T10
20T10
25T10
30T10
Roll Length Roll Length
(ft)
(m)
249
197
157
131
76
60
48
40
Part No.
32T10
25T20
Roll Length Roll Length
(ft)
(m)
121
128
37
39
20mm
Pitch
P O W E R
T R A N S M I S S I O N
P R O D U C T S S Y N C H R O N O U S
2 0 1 0
Polyurethane Belts
ELA T E C H * D i s t r i b u t e d B y V e y a n c e T e c h n o l o g i e s
A pp l i c a t i o n s
S Y N C H R O N O U S
Polyurethane belts can be used in open end, jointed/
spliced, or truly endless configurations in a variety of
applications.
Typical applications for the open end configuration are
in linear motion devices and other drives where precise
motion is required.
Typical application for the spliced configuration are in
light conveyors and other material process and transfer
industries.
Belting For A Wide Variety
o f A pp l i c a t i o n s
ELATECH distributed by Veyance Technologies is a full line of
polyurethane belting covering a full range of applications – linear
motion, and conveying and power transmission.
ELATECH’s Polyurethane belts are a combination of a
polyurethane body reinforced with special steel or aramid tension
members to fulfill the most severe industrial requirements.
Key Features & Benefits
•Polyurethane material resists flaking, has higher
dimensional stability, and has superior wear and
abrasion resistance.
•Higher flexibility
The tension members are high tensile steel that offer excellent
dimensional stability for accurate positioning and less maintenance.
Construction with special cords is available upon request.
Available product styles include:
ELATECH M – Open End
ELATECH V – Jointed
ELA-flex SD – Truly Endless
iSync – TrulyEndless Sleeves
Wide Range of Backings
Cleat Attachments
Truly endless due to having no splice or welding, are ideal
in high load conveying or power transmission applications.
A special polyamide fabric on the tooth facing (special order) can
reduce friction, improve tooth engagement, and reduce noise.
and
The unique chemical and mechanical characteristics of
polyurethane belts along with the possibility of a variety of
backings are ideal for conveying applications.
It is possible to attach a variety of cleats on all of ELATECH’s
polyurethane belts for conveying, handling, and positioning.
Belt Construction Engineered
For Excellence
ELATECH belts are manufactured with a body of thermoplastic
polyurethane providing superior wear and abrasion resistance. It
can be an ideal choice where cleanliness is critical. The precise
manufacturing process, coupled with the polyurethane belt
material, ensures a reliable and dimensionally stable product.
Built For Extreme Conditions
The chemical properties of polyurethane belting make them
highly resistant to:
• Hydrolysis
• Ozone
• UVA
• Aging
• Oils, greases and fats
• Gasoline
• Good resistance to acids
ELATECH’s product line has a working temperature range of
15°F. to 175°F (peaks up to 230°F).
More Information
Full product offering, technical data, and drive data can be
obtained in the ELATECH Polyurethane Belts catalog.
* ELATECH is a trademark of ELATECH S.r.l.
Contact your local Goodyear Engineered Products PTP industrial distributor
or go to www.goodyearep.com/ptp to locate one.
41
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S Polyurethane Belts
ELA T E C H * D i s t r i b u t e d B y V e y a n c e T e c h n o l o g i e s
Available Sizes
T
T5
T10
AT
AT5
T20
S Y N C H R O N O U S
4
6
10
20
50
100
10
12
16
20
25
32
50
75
100
10
16
20
25
32
50
75
100
150
AT20
10
12
16
20
25
32
50
75
100
25
32
50
5
100
150
10
16
25
32
50
75
100
150
25
32
50
75
100
150
Truly Endless
Profile
Available
Lengths (mm)
T2.5
T5
T10
AT5
AT10
120 – 950
165 – 1440
260 – 2250
330 – 1050
560 – 1940
ATL
ATL5
ATL10
ATL20
10
16
25
32
50
75
100
25
32
50
75
100
150
10
12
16
20
25
32
50
RTD
RTD5M RTD8M RTD14M
10
15
20
30
50
85
100
300-400
HTD3M
HTD5M
10
15
25
50
100
10
15
25
50
100
STD5M
STD8M
10
15
25
50
100
10
15
20
30
50
85
100
Inch
10
15
20
30
50
85
100
40
55
85
100
115
F1
F2
F3
10
25
50
100
25
50
75
100
25
50
75
100
Flat
Width (mm) Width (mm)
40
55
85
100
115
Width (mm) Width (mm) Width (mm)
ATK
TK
XL
L
H
6.35
9.4
12.7
19.05
25.4
38.1
50.8
101.6
12.7
19.05
25.4
38.1
20.8
101.6
12.7
19.05
25.4
38.1
20.8
76.2
101.6
XH
Width (mm) Width (mm) Width (mm) Width (mm)
* ELATECH is a trademark of ELATECH S.r.l.
25.4
38.1
50.8
76.2
101.6
HTD8M HTD14M
Width (mm) Width (mm) Width (mm) Width (mm)
STD
Width (mm) Width (mm) Width (mm)
10
15
25
50
100
Available Max.
Widths (mm)
HTD
Width (mm) Width (mm) Width (mm)
42
AT10
Width (mm) Width (mm) Width (mm)
Width (mm) Width (mm) Width (mm)
TK-K6
TK10-K13
ATK5-K6
Width (mm)
Width (mm)
Width (mm)
16
25
32
50
75
100
25
32
50
75
100
16
25
32
50
75
100
ATK10-K13
Width (mm)
25
32
50
75
100
P O W E R
T R A N S M I S S I O N
P R O D U C T S Eagle
®
S Y N C H R O N O U S
A cc u l i n e a r
2 0 1 0
®
A pp l i c a t i o n s
Eagle Pd Acculinear belts can be used in open-end or
spliced configurations in a variety of applications.
Part No: Y-8-PU-16-STD
Y
Alphabetical designation denotes belt width
(Y=16 mm Wide Belt)
8
8 mm Belt Pitch
PU
Polyurethane
16
Belt Width (16 mm)
STD Standard Construction
The Benefits
Belts… Now
of
in
Eagle Synchronous
Polyurethane Material
Eagle Pd Acculinear combines the advantages of polyurethane
with the unique H.O.T. (Helical Offset Tooth) geometry for a
low-maintenance belt that resists wear. Polyurethane belts resist
flaking, offer high resistance to oils, fats and greases, and are more
abrasion-resistant than rubber products. With high flexibility and
long life, Eagle Pd Acculinear is a revolutionary choice for a wide
range of applications.
Self-Tracking Sprocket
When it comes to performance, Eagle Pd Acculinear belts and
sprockets are right on track. The key to success lies in the system’s
patented H.O.T. geometry. With this self-tracking configuration,
the sprocket’s left and right helixes guide the thermoplastic
polyurethane belt to the center of the Eagle Pd Acculinear sprocket.
And there it remains: no waste, no wander, just improved
efficiency and wear resistance in a compact design. The H.O.T.
geometry eliminates belt wander and the need for flanges. As a result,
Eagle Pd Acculinear sprockets can be used on slider bed applications
where flanges would normally protrude above the bed surface.
Low Vibration
Eagle Pd Acculinear and the H.O.T. design minimize belt vibration
on flat pulleys used on the entry and exit of slider beds. The belt
moves progressively over straight edges, reducing noise and vibration.
S Y N C H R O N O U S
Typical applications for the open-end configuration are
in linear motion devices and other drives where precise
motion is required.
Typical application for the spliced configuration are
in light conveyors and other material processing and
transfer industries.
Key Features & Benefits
• Polyurethane material resists flaking, has higher
dimensional stability, and has superior wear and abrasion resistance.
• Self-tracking and compact drives.
• Less vibration and reduced noise.
• High flexibility.
• High-Precision linear positioning.
H.O.T. Geometry Delivers
Quieter Drive
This innovative polyurethane belt and sprocket system uses our
proprietary technology to deliver noise levels far below the
industry standard. The unique design of Eagle Pd Acculinear belts and
sprockets is the reason for the system’s superior noise reduction. The
self-tracking belt is guided to the center of the sprocket—delivery
that smooths out tooth engagement unlike any other tooth geometry.
Belt Constructions Engineered
for Excellence
The tooth and backing material are made of thermoplastic
polyurethane, which provides superior wear and abrasion
resistance. It’s an ideal choice in applications where cleanliness
is critical. The precise manufacturing process, coupled with the
polyurethane belt material, ensures a reliable and dimensionally
stable product.
The tension members are high tensile steel and offer excellent
dimensional stability for accurate positioning and less
maintenance.
The tooth facing offers reduced coefficient of friction with the
sprocket and also provides wear and abrasion protection.
The tooth geometry eliminates the chordal effect that occurs around
the tooth sprocket and reduces drive vibration.
To learn more visit www.goodyearep.com/ptp.
43
P O W E R
T R A N S M I S S I O N
P R O D U C T S Eagle
®
S Y N C H R O N O U S
A cc u l i n e a r
®
S Y N C H R O N O U S
Open-End Belt Configuration
Special Belt Constructions
Eagle Pd Acculinear belts are manufactured in open-end rolls with
a standard roll length of 300 feet. The belt is manufactured with
the tension members lying parallel to the belt edge so that the
load is equally distributed across all tension members. A common
application of open-end belts is in linear motion drives. Clamping
plates are available for open-end Eagle Pd Acculinear belts to
mechanically join the belt’s ends.
In addition to the standard belt construction (polyurethane
backing material), Eagle Pd Acculinear is available in a variety
of special constructions. Several materials can be applied to the
back of the belt to enhance its performance in specific drive envi­
ronments. These backing materials are typically used when special
characteristics are required on the back of the belt to transfer specific
materials in conveyor ­applications.
Linear Motion Drive
(Open-End Belt)
A number of special backings are available on request. Refer to
the appropriate engineering manual or to the Web site for more
information on these special backings.
Eagle Pd Acculinear is available in 8 standard widths
(in 8 and 14 mm pitch configurations)
Spliced Belt Configuration
Lengths of open-end Eagle Pd Acculinear can also be thermetically
spliced to obtain any continuous length of endless belting. These
spliced Eagle Pd Acculinear belts are primarily used in light
conveyor applications, where long endless belts are required.
Linear Conveyance Application
(SPLICED BELT)
Sample Part Number
Y - 8 - Pu - 16 - Std
Belt Type: Open-End
Belt Length: 800 mm
Y = Eagle Pd 16 mm Wide Belt
8 = 8mm Pitch
PU = Polyurethane
16 = Belt Width, in mm
STD = Belt Construction (STD = Standard Construction)
Alphabet Designation
(denotes belt width, e.g.:
Y = 16mm wide belt)
Sprockets
Eagle Pd Acculinear Sprockets for the polyurethane belt line are
available for all eight belt widths in a wide range of ­diameters.
The Eagle Pd Acculinear product shares the same sprockets as the
rubber Eagle Pd® product. The only exception is with the “M”
(25mm width) and the “L” (50mm width) sprockets. These two
widths are stocked in aluminum and are offered in a limited size
range. All other sprocket widths are stocked either in ductile or
cast iron. Refer to the “Eagle Pd Acculinear Sprocket” section for
more ­information.
44
Belt Pitch
(8mm or 14mm)
PU for
Polyurethane
1: Y
-
8
-
PU -
16
2: M
-
8
-
PU -
25
3: W
-
8
-
PU -
32
4: L
-
8
-
PU -
50
5: B
-
14 -
PU -
35
6: G
-
14 -
PU - 52.5
7: 0
-
14 -
PU -
70
8: R
-
14 -
PU -
105
Belt Width
in mm
State Belt
Construction
State “Open-End”
or “Spliced”
State Belt
Pitch Length
T R A N S M I S S I O N
P R O D U C T S Eagle
®
S Y N C H R O N O U S
A cc u l i n e a r
E a g l e P d A cc u l i n e a r S p r o c k e t s
for
Sprocket Face Width (F) = 26mm, Pitch = 8mm
Sprocket Part
Number
Hub*
Bore Range
(inches)
MIN.
MAX.
M-20S-MPB
MPB 0.5000
M-22S-MPB
MPB 0.5000
M-24S-MPB
MPB 0.5000
M-26S-MPB
MPB 0.5000
M-28S-MPB
MPB 0.5000
M-30S-MPB
MPB 0.5000
M-32S-MPB
MPB 0.5000
M-34S-MPB
MPB 0.5000
M-36S-MPB
MPB 0.5000
M-38S-MPB
MPB 0.5000
M-40S-MPB
MPB 0.5000
M-56S-MPB** MPB 0.5000
M-90S-MPB** MPB 1.0000
**These sprocket sizes are nonstock items.
1.0630
1.2200
1.3390
1.5350
1.6140
1.7720
1.8900
2.0080
2.1650
2.2830
2.4410
3.5040
2.8740
20
22
24
26
28
30
32
34
36
38
40
56
90
1
1
1
1
1
1
1
1
1
1
1
1
2
2.0050
2.2060
2.4060
2.6070
2.8070
3.0080
3.2080
3.4090
3.6090
3.8100
4.0100
5.6140
9.0230
1.9508
-
2.1513
-
2.3518
-
2.5523
-
2.7528
-
2.9533
-
3.1538
-
3.3543
-
3.5549
-
3.7554
-
3.9559
-
5.5600
-
8.9686 8.0299
0.4700
0.4700
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
Bore Range
(inches)
MIN.
MAX.
L-20S-MPB
MPB 0.500
L-22S-MPB
MPB 0.500
L-24S-MPB
MPB 0.500
L-26S-MPB
MPB 0.500
L-28S-MPB
MPB 0.500
L-30S-MPB
MPB 0.500
L-32S-MPB
MPB 0.500
L-34S-MPB
MPB 0.500
L-36S-MPB
MPB 0.500
L-38S-MPB
MPB 0.500
L-40S-MPB
MPB 0.500
L-56S-MPB** MPB 0.500
L-90S-MPB** MPB 1.000
**These sprocket sizes are nonstock items.
1.063
1.220
1.339
1.535
1.614
1.772
1.890
2.008
2.165
2.283
2.441
3.504
2.874
25mm Wide Belt
1.6000
-
1.8100
-
2.0100
-
2.2800
-
2.4400
-
2.6400
-
2.8300
-
3.0300
-
3.2300
-
3.4300
-
3.6200
-
5.2400
-
4.7200 0.3150
for
Sprocket Face Width (F) = 51 mm, Pitch = 8 mm
Sprocket Part
Number
Hub*
®
No.
Pitch
Wt. Approx. WR2
O
I
E
H
T
L
of
Diameter
Material (lbs)
(lbs.-ft2)
Teeth Type* (inches)
(inches) (Refer to Type I below)
E a g l e P d A cc u l i n e a r S p r o c k e t s
2 0 1 0
1.5000
1.5000
1.6500
1.6500
1.6500
1.6500
1.6500
1.6500
1.6500
1.6500
1.6500
1.6500
1.6500
Al
Al
Al
Al
Al
Al
Al
Al
Al
Al
Al
Al
AI
0.33
0.41
0.55
0.68
0.80
0.93
1.08
1.23
1.40
1.57
1.75
3.53
5.29
0.0009
0.0015
0.0023
0.0034
0.0047
0.0063
0.0083
0.0108
0.0138
0.0174
0.0217
0.0903
0.2867
S Y N C H R O N O U S
P O W E R
50mm Wide Belt
No.
Pitch
Wt. Approx. WR2
O
I
E
H
T
L
of
Diameter
Material (lbs)
(lbs.-ft2)
Teeth Type* (inches)
(inches) (Refer to Type I below)
20
22
24
26
28
30
32
34
36
38
40
56
90
1
1
1
1
1
1
1
1
1
1
1
1
2
2.005
2.206
2.406
2.607
2.807
3.008
3.208
3.409
3.609
3.810
4.010
5.614
9.023
1.9508
-
2.1513
-
2.3518
-
2.5523
-
2.7528
-
2.9533
-
3.1538
-
3.3543
-
3.5549
-
3.7554
-
3.9559
-
5.5600
-
8.9686 8.0299
0.4700
0.4700
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
0.6300
1.6000
-
1.8100
-
2.0100
-
2.2800
-
2.4400
-
2.6400
-
2.8300
-
3.0300
-
3.2300
-
3.4300
-
3.6200
-
5.2400
-
4.7200 0.3937
2.4800
2.4800
2.6400
2.6400
2.6400
2.6400
2.6400
2.6400
2.6400
2.6400
2.6400
2.6400
2.6400
Al
Al
Al
Al
Al
Al
Al
Al
Al
Al
Al
Al
AI
0.55
0.69
0.90
1.10
1.29
1.51
1.74
1.99
2.25
2.53
2.83
5.65
8.16
0.0027
0.0036
0.0054
0.0072
0.0089
0.0111
0.0138
0.0179
0.0228
0.0287
0.0357
0.1470
0.4820
Notes:
1.
2.
3.
4.
5.
Al = Aluminum (uncoated).
Sprockets are only available in MPB.
The “L”(50mm width) and “M” (25mm width) belts are nonstock items which need to be quoted and may have
a longer lead time.
Sprocket dimensions and material are subject to change.
Please contact your Goodyear Engineered Products PTP
industrial distributor for sprocket sizes and materials not listed
in this manual or visit goodyearep.com to locate one.
LH
RH
LH is the left-hand helix.
RH is the right-hand helix.
Note: For proper installation, orientation of teeth must be
in the same direction on all sprockets in the drive.
*Type I
*Type II
Web
45
P O W E R
T R A N S M I S S I O N
S Y N C H R O N O U S
P R O D U C T S Eagle
®
A cc u l i n e a r
®
A cc u l i n e a r C l a m pi n g P l a t e s
Clamping Plates are available for Eagle Pd Acculinear Open-end belts
to allow them to be used in Linear Motion Devices.
S Y N C H R O N O U S
A
L
B
Clamping Plates
Belts
B
(mm)
L
(mm)
Material
1: Y-8-PU-16
12
75
120
AL
2: M-8-PU-25
12
75
120
AL
3: W-8-PU-32
12
75
120
AL
4: L-8-PU-50
12
75
120
AL
5: B-14-PU-35
18
130
200
AL
6: G-14-PU-52.5
18
130
200
AL
7: O-14-PU-70
18
130
200
AL
8: R-14-PU-105
18
130
200
AL
AL = Aluminum
46
A
(mm)
Part
Number
Eagle Pd — 8mm — Clamping Plate
Eagle Pd — 14mm — Clamping Plate
P O W E R
T R A N S M I S S I O N
P R O D U C T S B A N D E D
2 0 1 0
Banded Belts
Because of their banded or joined construction, these belts tend
to prevent rollover and reduce vibration tendencies. Banded
belts are usually better suited to unusual drive situations than
are matched belt sets. They are available in the classical cross
sections (A, B, C, & D), narrow cross sections (3V, 5V, & 8V), and
Poly-V® cross sections (H, J, L, & M).
Typical applications for banded V-belts include vertical shaft
drives, clutching drives, and V-flat drives. (V-belt drives are where
the inside of the belt drives a flat pulley on the slower speed shaft.)
so severe that belts interface with each other and turn over in the
grooves or even jump out of the grooves. Banded V-belts eliminate
such problems.
Banded V-belts are recommended for use where belt vibration or
belt whip causes unsatisfactory results when conventional multiple
single V-belts are used. Such situations are not uncommon on
drives with a combination of long belt spans and/or pulsating
loads as created by an internal combustion engine or reciprocating
pumps and compressors. In such cases, belt whip may become
Another advantage of banded V-belts is the considerable degree
of design flexibility they can provide since they operate just as
effectively when they, in turn, are used as match sets. A twobelt unit for example, has sufficient lateral rigidity so as to not
interface with the units in adjacent grooves.
B A N D E D
C l a s s ic a l & N a r r o w B a n d e d V - B e l t s
T o r q u e T e a m P l u s ® (F l e x t e n ® -R e i n f o r c e d B a n d e d V-B e l t s )
These belts are available for low-speed, high-power applications
which were previously considered to be in the domain of chain
or gears. Flexten-reinforced Torque Team Plus 5V and 8V
banded belts are ideally suited to handle many of the applications
that have been reserved for chain or gears.
P o l y - V (V-R i bbed )
Poly-V belts are flat belts with a series of longitudinal ribs on the
driving face that mate with grooves in the sheave rim. Relatively
thin, with a well-supported tensile member, these belts perform
better than V-belts on drives with small sheave, high speeds,
reverse bends, and high-speed ratios. Poly-V belts generally run
smoother than V-belts, and their low weight makes them suitable
for high-speed drives.
Three cross sections, designated J, L, and M, handle the same
range of industrial applications as narrow or classical belts.
A smaller section, H, is used for small sheave and miniature
drives. Finally, the K section Poly-V is often located in the
Automotive industry.
47
P O W E R
T R A N S M I S S I O N
B A N D E D
P R O D U C T S Torque Team
®
(Laminated)
A pp l i c a t i o n s
Some of the most common drives recommended for
consideration include:
•Debarkers
• Gang Saws
•Chip-n-Saws
• Deck Saws
•Cut-Off Saws
• Trimmers
•Chippers
Key Features & Benefits
Part No: 3/5VL800
3/
3 Rib Joined Construction
5V
0.62˝ Top Width – Narrow Profile Rib
L
Laminated Construction
800
80.0˝ Nominal Outside Length
B A N D E D
Solve the Toughest Sawmill
D r i v e P r ob l e m s
Goodyear Engineered Products Torque Team Laminated V-belts
are particularly effective when installed on drives that experience
frequent slippage caused by logs and heavy lumber that jam or
impact the equipment.
•Narrow profile ribs provide savings through
efficiency.
•Joined construction for problem drives.
•High horsepower capacity.
•High-strength Vytacord tensile members.
•Laminated construction engineered to slip.
•Tough fabric backing.
•Oil, heat, ozone, and abrasion resistant.
•Static conductive.*
Reduce Downtime & Maintenance
Goodyear Engineered Products Torque Team Laminated V-belts
can withstand the punishment that results from jams in log and
lumber processing applications.
Standard V-belts resist slipping when a jam occurs, causing
excessive heat buildup that can lead to belt failure and costly
downtime. But that won’t happen with Torque Team Laminated
V-belts on the job.
The special sidewall of Torque Team Laminated V-belts acts as
a control switch, allowing the belts to slip as needed until the
obstruction is cleared. As a result, the superior wear-resistant
capabilities of Torque Team Laminated V-belts are maintained,
increasing belt life up to four times longer than standard V-belts.
High Strength
for
Available
of Sizes
in a
Wide Variety
Goodyear Engineered Products Torque Team Laminated V-belts
are available in the 5VL belt cross section and in most standard
lengths. The 5VL laminated V-belt is interchangeable with all
standard 5V and 5VX V-belts currently found on these drives. They
can also be cut to a variety of rib widths, depending on your drive
requirements. This ensures a perfectly-matched set of V-belts that
can further enhance drive performance.
Long Life
Goodyear Engineered Products Torque Team Laminated V-belts
feature our powerful Vytacord® tensile members. Vytacord provides
high strength and horsepower ratings, yet serves as a more forgiving
reinforcement that will give under excessive tension instead of
snapping. That means increased belt life.
5 v l C r o s s S e cti o n V i e w
Sizes
5VL800
5VL850
5VL900
5VL950
5VL1000
5VL1060
5VL1120
5VL1180
5VL1250
5VL1320
5VL1700
For longer 5V, as well as 3V and 8V laminated profiles not listed here, contact your Goodyear Engineered Products PTP industrial distributor.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
48
P O W E R
T R A N S M I S S I O N
P R O D U C T S B A N D E D
HY - T W e d g e T o r q u e T e a m
®
2 0 1 0
®
A pp l i c a t i o n s
For shock load applications. Ideal for pulsating loads,
high capacity drives, and for short-center, heavy-duty
drives.
Part No: 3/8V1900
3/
3 Rib Joined Construction
8V
1.00˝ Top Width – Narrow Profile Rib
1900 190.0˝ Nominal Outside Length
Single Envelope Ply on 5Vs
2 Envelope Plies on 8Vs
Envelope Uncogged Construction Shown
T a m e Y o u r P r ob l e m D r i v e s
Pulsation, vibration, shock loads, and misalignment are problems
for any team of V-belts, no matter how perfectly matched the
individual units. These conditions often lead to chronic belt whip
or to belt turnover, resulting in premature wear or sudden failure
of one or more belts. Of course, when one belt goes, the whole
team has to be replaced.
HY-T Wedge Torque Team belts are built with multiple belts
joined by a tough, rubber-impregnated fabric backing that
regulates belt travel so all ribs pull together as a single, perfectly
matched team. Yet each rib is free to wedge into the sheave
groove for maximum traction, maximum power, and transmission
efficiency.
Operating in standard sheave grooves without sheave or drive
modification, they can tame any problem drives now in operation.
Or they can fit right in with your new drive designs without
special modifications.
Designed & Built to Deliver
Superior Performance
V-belt performance begins with the tension members, so we built
HY-T Wedge Torque Team V-belts with super strong Vytacord. It
provides the high-strength, high-horsepower rating capacity needed
to effectively transmit drive power. And it’s tough enough to tolerate
the misalignment that quickly destroys belts. The Vytacord material
is a polyester construction with excellent strength and minimal
elongation. Drive performance is consistent, reliable, and predictable
over the life of the belt.
We then add a tough oil-and abrasion-resistant fabric backing to
provide maximum longitudinal flexibility and lateral strength to
withstand the dynamic forces acting within a joined belt. The
backing also has special adhesion characteristics that enable it to
bond to the V-sections to maintain the integrity of the belt.
•Narrow profile ribs provide savings through
efficiency.
•Joined construction for problem drives.
•Strong Vytacord® tensile members.
•Tough fabric backing.
•Oil, heat, ozone, and abrasion resistant.
•Available in raw edge construction with cogs or
envelope construction.
•Matchmaker to eliminate mismatch.
•Static conductive.*
B A N D E D
Key Features & Benefits
The cushion is made of fiber-reinforced, engineered compounds
providing oil, heat, ozone, and abrasion resistance.
W e d g e o r E n v e l op e C o n s t r u c t i o n s
Provide Optimum Performance
HY-T Wedge Torque Team belts are available in a raw edge
construction with cogs for increased flexibility and heat dissipation
or envelope construction for drives where pulsation, shock loads,
high tension, and long center are involved.
HY-T Wedge Torque Team Cogged belts have high-horsepower
belt construction and are identified with a 3VX or 5VX prefix
and are available in lengths up to 140˝. The cogged construction
provides the high flexibility required for short center distances. The
cogs also provide a larger surface area to dissipate heat and prolong
belt life. Improved material properties and advanced construction
technology result in an average horsepower increase of 30% over
standard joined “Classical” V-belts.
HY-T Wedge Torque Team Envelope belts are identified with
a 3V, 5V, or 8V prefix and are recommended for drives where
pulsation, shock loads, high tension, and long centers are involved.
They feature a continuous V-section that is protected by a
wide angle, synthetic fabric-impregnated, high-quality rubber
compound. The unique envelope achieves the high strength that
the HY-T Wedge Torque Team belts need to withstand high
loading forces. It also helps provide the torsional rigidity in long
center drives delivering the traction needed for accurate tracking
and precision performance.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
49
P O W E R
T R A N S M I S S I O N
B A N D E D
P R O D U C T S HY - T W e d g e T o r q u e T e a m
®
®
Matchmaker® Performance
Our Matchmaker technology results in belt consistency run to run.
That means each HY-T Wedge Torque Team is equal in size and
performance to every other HY-T Wedge Torque Team belt in
that size, no matter when or where it was produced.
By eliminating mismatch problems, there is no costly and
complicated belt matching to get a drive back on line; no problems
with belts that are too tight or too loose.
A v a i l a b l e i n t h e M os t E x t e n s i v e
Stock Line in the Industry
B A N D E D
HY-T Wedge Torque Team belts are available from stock in any
number of belts per team, up to the number of ribs indicated.
Nonstock lengths are also available in these rib counts, up to a
maximum of 730˝ (180˝ for 3V cross sections).
Cut Edge
3 v x , 5 v x C r o s s S e cti o n
Cut Edge Side View
Part
Number
Max No.
Ribs per Slab
3VX250
3VX265
3VX280
3VX300
3VX315
3VX335
3VX355
3VX375
90
90
90
90
90
90
90
90
Part
Number
Max No.
Ribs per Slab
5VX500
5VX530
5VX560
5VX600
5VX630
5VX670
5VX710
5VX750
5V750*
5VX800
5V800
53
53
53
53
53
53
53
53
53
53
42
Part
Number
Max No.
Ribs per Slab
8V1000
8V1060
8V1120
8V1180
8V1250
8V1320
8V1400
8V1500
14
14
14
14
24
24
24
24
*Cut edge, non-cogged.
50
Envelope
5 v , 8 v C r o s s S e cti o n
Part
Number
Max No.
Ribs per Slab
3VX400
3VX425
3VX450
3VX475
3VX500
3VX530
3VX560
3VX600
90
90
90
90
90
90
90
90
Part
Number
Max No.
Ribs per Slab
5VX850
5V850
5VX900
5V900
5VX950
5V950
5VX1000
5V1000
5VX1060
5V1060
5VX1120
53
42
53
42
53
42
53
42
53
42
53
Part
Number
Max No.
Ribs per Slab
8V1600
8V1700
8V1800
8V1900
8V2000
8V2120
8V2240
8V2360
24
24
24
24
24
24
24
24
Part
Number
Max No.
Ribs per Slab
3VX630
3VX670
3V670
3VX710
3VX750
3VX800
3VX850
3VX900
90
90
90
90
90
90
90
90
Part
Number
Max No.
Ribs per Slab
5V1120
5VX1180
5V1180
5VX1250
5VX1320
5VX1400
5V1500
5V1600
5V1700
5V1800
5V1900
42
53
42
53
53
53
42
42
42
42
42
Part
Number
Max No.
Ribs per Slab
8V2500
8V2650
8V2800
8V3000
8V3150
8V3350
8V3550
8V3750
24
24
24
24
24
24
24
24
Part
Number
Max No.
Ribs per Slab
3VX950
3VX1000
3VX1060
3VX1120
3VX1180
3VX1250
3VX1320
3VX1400
90
90
90
90
90
90
90
90
Part
Number
Max No.
Ribs per Slab
5V2000
5V2120
5V2240
5V2360
5V2500
5V2650
5V2800
5V3000
5V3150
5V3350
5V3550
Part
Number
8V4000
8V4250
8V4500
8V4750
8V5000
8V5600
8V6000
42
42
42
42
42
42
42
42
42
42
42
Max No.
Ribs per Slab
24
24
24
24
24
24
24
P O W E R
T R A N S M I S S I O N
P R O D U C T S B A N D E D
Torque Team Plus
2 0 1 0
®
A pp l i c a t i o n s
Ultimate upgrade belt; for all heavy-duty industrial
machinery and equipment. Ideal for operation in harsh
elements on the toughest high horsepower drives.
•Crushers
• Screens
•Saws
• Lathes
•Sanders
• Dryers
•Blow Tanks
• Chain Drives
•Washers
Performance Plus for High
H o r s e po w e r D r i v e s
Torque Team Plus belts are our highest capacity V-belts and
known for strength, durability, and performance.
Their tension members are Flexten or aramid cable cords. They are
twisted from aramid fiber which is five times stronger than steel,
then are treated for improved adhesion, improved flex life, and
increased resistance to shrinkage. Torque Team Plus belts exhibit
only one half of the initial elongation of other belts and maintain
greater dimensional stability over the life of the belt. They stand
up to higher horsepower, high-tension drive requirements, shock
loads, and abusive installations better than standard joined belts,
multiple V-belt teams, or chain and sprocket drives.
The cushion is made of a highly engineered compound that
resists harsh operating environments and compression fatigue.
The envelope is also rubber compound-impregnated to protect
the carcass from abrasion, heat, ozone and oil. Together, these
components offer a strong, flexible, efficient belt with extended
service life.
The Advantages of
Torque Team Plus Belting
With Torque Team Plus, there’s less cost involved in the drive
design due to the fact that each belt can handle a given load with
a narrower width belt than either multiple V-belt or chain and
sprocket drives. This means that there is less cost incurred for the
drive medium (belts/chains), less cost for the narrower sheaves and
pulleys they use, and less cost for the downtime and labor involved
in the retensioning required by both multiple V-belt and chain
belt drives. There is no need for the lubricants and lubrication
system that chain drives need. These are some very clear advantages,
especially when you consider that you get these savings along with
a dramatic performance advantage.
Key Features & Benefits
•Narrow profile ribs provide savings through
efficiency.
•Joined construction for problem drives.
•Up to 50% more horsepower capacity.
•High-strength Flexten tensile members.
•Oil, heat, ozone, and abrasion resistant.
•Static conductive.*
B A N D E D
Part No: 3/5VF2000
3/
3 Rib Joined Construction
5V
0.62˝ Top Width – Narrow Profile Rib
F
Torque Team Plus With Flexten® Tensile Member
2000 200.0˝ Nominal Outside Length
Single Envelope Ply on 5Vs, 2 Envelope Plies on 8Vs
There is also less weight because the smaller sheaves used for drives
using Torque Team Plus belts are a dramatic 50% lighter than
a sheave required to drive an equal horsepower multiple V-belt
drive. When compared to an equal horsepower chain drive, the
sheave weighs an incredible 65% less than the sprocket required
for the chain drive.
Torque Team Plus is more compact. In fact, a typical Torque
Team Plus belt is only one-third the width of an equivalent
multiple V-belt team. It needs 17% less space than an equivalent
chain drive.
And since Torque Team Plus belts give you all the advantages
of the joined principal (smooth tracking, no belt turnover, no
matching problems, less belt threatening vibration, even and
consistent tensioning), there is less maintenance required.
Premium Torque Team Plus Belts
Require Adequate Sheaves
The high strength of Torque Team Plus belts provides
exceptional high-torque capabilities and horsepower ratings.
These high belt capacities may exceed standard sheave capabilities.
To assure safety and satisfactory drive operation, consult your
sheave supplier for sheave recommendations.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
51
P O W E R
T R A N S M I S S I O N
P R O D U C T S B A N D E D
Torque Team Plus
®
5 v f & 8 v f C r o s s S e cti o n V i e w
B e l t C r o s s S e cti o n s & L e n g t h s A v a i l a b l e
B A N D E D
Part
Number
Max No.
Ribs per Slab
5VF900
5VF950
5VF1000
5VF1060
5VF1120
5VF1180
5VF1250
5VF1320
42
42
42
42
42
42
42
42
Part
Number
Max No.
Ribs per Slab
8VF1250
8VF1320
8VF1400
8VF1500
8VF1600
8VF1700
8VF1800
8VF1900
24
24
24
24
24
24
24
24
Part
Number
Max No.
Ribs per Slab
5VF1400
5VF1500
5VF1600
5VF1700
5VF1800
5VF1900
5VF2000
5VF2120
42
42
42
42
42
42
42
42
Part
Number
Max No.
Ribs per Slab
8VF2000
8VF2120
8VF2240
8VF2360
8VF2500
8VF2650
8VF2800
8VF3000
24
24
24
24
24
24
24
24
Part
Number
Max No.
Ribs per Slab
5VF2240
5VF2360
5VF2500
5VF2650
5VF2800
5VF3000
5VF3150
5VF3350
42
42
42
42
42
42
42
42
Part
Number
Max No.
Ribs per Slab
8VF3150
8VF3350
8VF3550
8VF3750
8VF4000
8VF4250
8VF4500
8VF4750
24
24
24
24
24
24
24
24
Torque Team Plus was designed to belt a drive with one band. They are not to be used in matching sets.
52
Part
Number
5VF3550
Part
Number
8VF5000
8VF5600
8VF6000
Max No.
Ribs per Slab
42
Max No.
Ribs per Slab
24
24
24
P O W E R
T R A N S M I S S I O N
P R O D U C T S B A N D E D
HY - T T o r q u e T e a m
®
2 0 1 0
®
( C l a s s ic a l )
A pp l i c a t i o n s
For shock load applications. Ideal for pulsating loads,
high-capacity drives, and short center heavy-duty drives.
Key Features & Benefits
Designed & Built to Deliver
Superior Performance
HY-T Torque Team Classical belts are built with strong Vytacord®
tension members. This provides the high-strength, high-horsepower
rating capacity needed to effectively transmit drive power. And it’s
tough enough to tolerate the misalignment that quickly destroys
belts. The Vytacord material has a very good dimensional stability.
Drive performance is consistent, reliable, and predictable over the
life of the belt.
We then add a tough oil- and abrasion-resistant fabric backing
to provide maximum longitudinal flexibility and lateral strength
to withstand the dynamic forces acting within a joined belt. The
backing also has special adhesion characteristics that enable it
to bond inseparably to the V-sections to maintain the unitary
integrity of the belt.
The cushion in the envelope construction is fiber-loaded Plioflex®.
Cut-edge constructions have a fiber-loaded, latest-technology
compound that contributes heat and oil resistance and strength.
B A N D E D
Part No: 3/BX112
3/
3 Rib Joined Construction
B
0.66˝ Top Width – Classical Profile Rib
X
Premium Cogged Construction
112
Approximate 112˝ Inside Length
Cut-Edge, Molded Cog Construction Shown
• Classical profile ribs.
• Joined construction for problem drives.
• High-strength Vytacord tensile members.
• Available in cut-edge or envelope construction with Plioflex cushion.
• Tough fabric backing.
• Heat, ozone, and abrasion resistant.
• Matchmaker to eliminate mismatch.
•Static conductive.*
a larger surface area to dissipate heat and to prolong belt life.
HY-T Torque Team Envelope belts are identified with a B or
C prefix and both cogged and non-cogged are static conductive.
They are recommended for drives where pulsation, shock loads,
high tension, and long centers are involved.
Matchmaker® Performance
Our Matchmaker technology results in belt consistency run
to run. That means each HY-T Torque Team Classical belt
is equal in size and performance to every other HY-T Torque
Team Classical belt in that size, no matter when or where it
was produced.
By eliminating mismatch problems, there is no costly and
complicated belt matching to get a drive back on line; no problems
with belts that are too tight or too loose.
C u t - E d g e o r E n v e l op e
Construction Provide Optimum
Performance
HY-T Torque Team Classical belts are available in a cut-edge
construction with cogs for increased flexibility and heat dissipation
or envelope construction for drives where pulsation, shock loads,
high tension, and long centers are involved.
HY-T Torque Team Cogged belts are high horsepower belt
constructions identified with a BX or CX prefix and are available
in lengths up to 136˝. The cogged construction provides the high
flexibility required for short center distances. The cogs also provide
To learn more visit www.goodyearep.com/ptp.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
53
P O W E R
T R A N S M I S S I O N
P R O D U C T S B A N D E D
HY - T ® T o r q u e T e a m ®
Cut-Edge
C r o s s S e cti o n
Envelope
C r o s s S e cti o n
( C l a s s ic a l )
Cut-Edge
Side View
B Profile
B A N D E D
Part
Number
Max No.
Ribs per Slab
BX35
BX38
BX42
BX43
BX46
BX48
BX50
BX51
BX52
BX53
BX54
BX55
BX56
BX57
BX58
BX59
BX60
BX61
BX62
BX63
BX64
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
Part
Number
Max No.
Ribs per Slab
BX65
BX66
BX67
BX68
BX70
BX71
BX72
BX73
BX74
BX75
BX77
BX78
BX79
BX80
BX81
BX82
BX83
BX84
BX85
BX87
BX88
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
Part
Number
Max No.
Ribs per Slab
Part
Number
Max No.
Ribs per Slab
BX90
BX93
BX95
BX96
BX97
BX99
BX100
BX103
BX105
BX108
BX112
BX120
BX124
BX128
BX133
BX136
*B55
*B56
B96
B103
B105
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
38
38
38
Part
Number
Max No.
Ribs per Slab
C112
C144
C158
C162
C173
C180
C195
C210
C225
C240
C255
26
26
26
26
26
26
26
26
26
26
26
Part
Number
Max No.
Ribs per Slab
D315
D330
D345
D360
D390
D420
D450
18
18
18
18
18
18
18
Part
Number
Max No.
Ribs per Slab
B112
B114
B115
B116
B118
B140
B144
B148
B150
B158
B162
B173
B180
B195
B210
B225
B240
B255
B270
B300
B315
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
Part
Number
Max No.
Ribs per Slab
C270
C285
C300
C315
C330
C345
C360
C390
C420
26
26
26
26
26
26
26
26
26
Part
Number
Max No.
Ribs per Slab
D480
D540
D600
D660
18
18
18
18
* Cut-edge non-cogged.
C Profile
Part
Number
Max No.
Ribs per Slab
CX60
CX68
CX75
CX81
CX85
CX90
CX96
CX99
CX100
CX105
CX108
36
36
36
36
36
36
36
36
36
36
36
CX109
CX112
CX120
CX124
CX128
CX136
C85
C90
C96
C105
C109
36
36
36
36
36
36
26
26
26
26
26
Part
Number
Max No.
Ribs per Slab
D210
D225
D240
D255
D270
D285
D300
18
18
18
18
18
18
18
D Profile
54
Part
Number
Max No.
Ribs per Slab
D120
D144
D158
D162
D173
D180
D195
10
18
18
18
18
18
18
P O W E R
T R A N S M I S S I O N
P R O D U C T S B A N D E D
2 0 1 0
Poly-V
®
A pp l i c a t i o n s
For small sheave compact designs requiring limited
vibration. Ideal for high-speed ratio drives with short
center distances.
• Exercise Equipment
• Automobiles
• Medical Equipment
• Power Equipment
• Farm Equipment
• Machine Tools
Part No: 180J6
18.0˝ Nominal Outside Length
J
J Section Poly-V
6
6 Ribs
One Belt That Can Do
The Work of Many
•Multiple V-ribbed profile provides friction and
wedge advantages.
•High-grade engineered rubber.
•Strong Vytacord® tensile member.
•L & M cross sections are milled in shorter lengths and are molded in longer lengths.
• Heat, ozone, and abrasion resistant.
The Poly-V belt is a single, endless belt with longitudinal
V-shaped ribs that mate consistently with the V-grooves in the
sheaves. It combines the convenience of a thin, one-piece flat belt
with the strong gripping traction of multiple V-belts to make the
Poly-V belt far better than either for many applications.
Longer Belt & Sheave Life
One Continuous Tension Member
f o r M a t c h l e ss P e r f o r m a n c e
Even distribution of stress on the belt also reduces differential
loading and wear on sheaves. It’s not unusual for Poly-V belt
sheaves to last significantly longer than standard V-belt sheaves
and to experience lower maintenance requirements during this
longer life.
To distribute the drive load evenly across the full width of the
sheave, the Poly-V belt is built as a single unit with a completely
supported, uninterrupted tension member. There is no matching
problem. No separate belts to turn over, grab, slip, or interfere
with each other.
The thin cross section profile allows use of smaller pulleys than
standard V-belts, and Poly-V belts handle speed ratios of 40:1.
With all this capacity, the Poly-V belt tracks properly without
special guides, flanges, crowns or deep grooves. And it resists
seating in the grooves, so speed ratios remain more consistent and
output speed remains more uniform.
More Power
in
L e ss S p a c e
Continuous engagement with the sheave driving surface gives
you greater power capacity per inch of width. In addition, wasted
space between separate V-belts is eliminated and converted into
narrower, shallower grooves. These provide substantially greater
contact area for stronger and more uniform traction.
B A N D E D
Key Features & Benefits
Complete support of the tension member, combined with full
and uniform engagement with the sheave grooves, eliminates
differential driving and equalizes belt stresses. That, in turn,
minimizes belt elongation and leads to significantly longer flex life.
Improve Drive Design
W h i l e Y o u R e d u c e D r i v e C os t
The combination of high-power capacity and low-profile design
means the Poly-V drive can improve the drive design while
lowering drive costs.
Poly-V belts allow narrower mounting clearances, need less center
distance adjustment, and require less take-up for tensioning.
Additionally, they allow the use of sheaves that are narrower in
width and smaller in diameter without sacrificing power capacity.
Smaller, narrower sheaves mean a reduction in weight so more of
the drive gets to the load for increased efficiency.
To learn more visit www.goodyearep.com/ptp.
55
P O W E R
T R A N S M I S S I O N
.12"
B A N D E D
P R O D U C T S Poly-V
®
.063"
.12"
H and K Sections are nonstock. Standard factory lead times will apply.
Minimums apply. Contact your local Goodyear Engineered Products
PTP industrial distributor.
.165"
.14"
.063"
.140"
H S e.12"
cti o n.165" K S e cti o n
0.092"
.14"
Stock Construction: No minimum quantity required. Can order any number of ribs up to maximum number of ribs per belt (Max Ribs/Belt) shown below.
.063"
J S e cti o n
.38"
0.092"
B A N D E D
.14"
0.185"
.38"
.12"
0.092"
0.185"
.38"
.14"
0.185"
.140"
Part Number Max Ribs/Belt Part Number Max Ribs/Belt
.51"
650J
68
.165"
180J
68
190J
200J
220J
240J
.140"
0.370"
260J
280J
.51"
300J
320J
340J
360J
.063" 380J
0.370"
400J
.51"
430J
.165"
460J
490J
520J
550J
0.370"
580J .140"
610J
0.092"
L S e cti o n*
.12"
.38"
.063"
0.185"
.165"
4"
.140"
0.092"
0.370"
730J
870J
920J
980J
68
68
68
68
100J*
105J*
110J*
120J*
140J*
147J*
204J*
210J*
230J*
243J*
270J*
310J*
328J*
353J*
40
40
40
40
46
45
68
68
70
68
68
145
145
145
Part Number Max Ribs/Belt Part Number Max Ribs/Belt
500L
540L
560L
615L
.51"
635L
655L
675L
695L
725L
0.370"
765L
780L
795L
815L
96
96
96
96
96
96
96
96
96
96
96
96
96
840L
865L
915L
975L
990L
1065L
1120L
1150L
1215L
1230L
1295L
1310L
1455L
96
96
96
96
96
96
96
96
96
96
96
96
72
420J*
444J*
552J*
546J*
575J*
640J*
690J*
770J*
776J*
810J*
878J*
890J*
895J*
904J*
940J*
994J*
1000J*
1200J*
145
68
68
68
145
68
145
145
68
145
145
68
145
145
145
145
145
145
Part Number Max Ribs/Belt
385L*
455L*
505L*
622L*
748L*
770L*
845L*
880L*
1073L*
1098L*
1180L*
96
96
72
96
96
96
96
96
96
72
96
*Static conductive
M S e cti o n *
.51"
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
Part Number Max Ribs/Belt
Part Number Max Ribs/Belt Part Number Max Ribs/Belt
900M
940M
990M
1060M
1115M
1150M
1185M
1230M
36
36
36
36
36
36
36
36
1310M
1390M
1470M
1610M
1650M
1760M
1830M
1980M
74
74
74
74
74
74
74
74
Part Number Max Ribs/Belt
2130M
2410M
2560M
2710M
3010M
3310M
3610M
74
74
74
74
74
74
74
*Static conductive
Special Note: Special Manufacture Belts are available. *Please check factory for availability.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check be added to drive
preventive maintenance programs where belt static conductivity is a requirement.
56
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S 2 0 1 0
V-Belts
V-belts include not only traditional classical and narrow
profiled belts, but also Double-V and FHP belts. When
synchronization or timing is not required, V-belts make an
excellent low-cost, quiet, and efficient means of transmitting
power. However, not all V-belts perform the same. Depending on
your application and your objectives, some V-belts will be better
at getting you closer to your end goal.
Narrow V-Belts
Effectively handling drives from 1 to 1,000 hp, these belts rank
high in horsepower-hours per dollar, the ultimate measure of drive
value. The narrow-belt cross sections (3V, 5V, and 8V), offer higher
power capacity for any sheave size and weight.
The narrow or “wedge” design provides more tensile member
support than classical V-belts. Narrow belts handle an equivalent
load, but with narrower face width and smaller diameters
than the traditional classical V-belts. These features allow
the use of smaller belts or fewer belts to transmit the load,
an important advantage if your goal is to maximize power
transmission efficiency by reducing drive weight and size.
C l a ss i c V - B e l t s
Many classical belts are used for replacement because it is
considered too costly to replace sheaves when upgrading
from classical to narrow or other belt types. Therefore, when
replacing classical sheaves, it is an opportune time to upgrade to
narrow or other belt types.
S p e c i a lt y V - B e l t s
When equipment calls for metric precision, you need a belt that
not only measures up, but one that won’t get lost in translation.
GY Metric belts are engineered to universal metric profiles,
but manufactured by Veyance Technologies in North America,
so you don’t have to go elsewhere to get them.
Double-V
or
Strong, flexible and able to work in wide temperature ranges, GY
Metric® replaces many common metric cross section belts such as
XPZ, XPA, SPA, ,XPB, SPB, XPC and SPC.
V - B E L T
The most widely used V-belts are A, B, C, and D classical belts.
Used more out of habit and convenience than design, these belts
can handle fractional to 500-hp drives, usually at the lowest
cost. However, they occupy more space, and the drives weigh
more than narrow-belt drives. Also, classical belts are usually less
efficient than narrow belts. But their versatility and wide range of
sizes and types make them an attractive alternative to wedge belts.
Hex Belts
A variation of the classical belt, Hex belts come in AA, BB, CC, or
a deep CCP cross section. These belts transfer power from either
side in serpentine drives. A drive design using Hex belts is more
complicated and engineering manuals should be consulted when
replacing or troubleshooting these drives.
FH P ( F r a c t i o n a l H o r s e po w e r B e l t s )
The 3L, 4L, and 5L light-duty FHP belts are part of the
V-Belt line also. As the name implies, these belts are used
soley on drives of 1 hp or less.
Cogged, Raw-Edge Construction
Goodyear Engineered Products provide a complete offering
of cogged, raw-edge belts in narrow, classical, and FHP styles.
Designated 3VX, 5VX, AX, BX, CX, 4L, and 5L, cogged, rawedge V-belts have higher capacity and efficiency, and they use
smaller sheaves than traditional envelope (wrapped) belts. These
belts have a higher coefficient of friction and are more aggressive,
which makes them a very efficient belt for power transmission.
Unlike conventional fabric-covered V-belts, raw-edge belts have
no cover. Thus, the cross-sectional area normally occupied by
the cover is used for more load-carrying cord. Cogs on the inner
surface of the belt increase air flow to enhance cooler running.
They also increase flexibility, allowing the belt to operate with
smaller sheaves. With classical V-belts, certain under-designed or
vs.
E n v e l op e C o n s t r u c t i o n
problem drives can be upgraded to “satisfactory” by substituting
classical cogged belts for classical envelope belts without
replacing sheaves.
Because of their higher coefficient of friction, cogged belts tend
to be more sensitive to alignment. While envelope belts can
tolerate some misalignment, cogged belts are more likely to turn
over under the same conditions. Cogged belts should not be used
in clutching drives, drives with severe shock loads, and drives that
have changing center distances, such as shaker screens. In these
applications, the aggressive nature and flexibility of cogged belts
can cause vibration, belt turnover, and belt breakage. Cogged
belts should also be avoided in drives that require slippage during
frequent stops and starts.
57
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S O p e n E n d V - B e l ti n g
A pp l i c a t i o n s
Ideal solution for temporary replacement in emergency
situations or for long center drives. They can be used
on all types of industrial applications.
Key Features & Benefits
Part No: B-Open End
B
0.66” Top Width – Classical Profile
Available Roll Lengths (see chart below)
T h e I d e a l S o l u t i o n f o r P r ob l e m
A pp l i c a t i o n s & E m e r g e n c y
Replacements
V - B E L T
Goodyear Engineered Products Open End V-belting is the
perfect answer for applications where endless V-belts are difficult
or impossible to install. It also serves as an ideal emergency
replacement when the exact length of endless belt is not readily
available.
•Universal classical profile.
•Multiple-ply, square-woven fabric tension members.
•Oil, heat, ozone, and abrasion resistant.
•Easy installation with spliced ends.
•Static conductive.*
H o r s e po w e r R a t i n g s
The horsepower ratings for fastened Open End V-belts are
approximately 30% of published horsepower ratings for
Goodyear Engineered Products standard multiple V-belts as
shown in our V-belt Engineering Manual (20044896).
Note: Because of differences in the elongation characteristics and
variations in cross section dimensions, Open End V-belts and
Endless V-belts should not be used together on multiple drives.
Open End V-belting will operate in any drive as long as RMA
standard sheave dimensions are observed and the recommended
maximum speed of 3,500 feet per minute is not exceeded. It is not
recommended as a permanent substitute for endless V-belts except
on drives where standard belts cannot be installed.
Regular Construction
Cut Lengths
A Section
B Section
C Section
D Section
A Section
B Section
C Section
Roll Lot: Either 250’ (max. 2 pcs.) or 500’ (max. 3 pcs.) approx. rolls. “D” section available only in 250’ (max. 2 pcs.) approx. rolls.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
To learn more visit www.goodyearep.com/ptp.
58
!
P O W E R
W
NE
T R A N S M I S S I O N
P R O D U C T S WEDGE TLP
™
V - B E L T
2 0 1 0
NARROW V-BELTS
Applications
Premium, longer-life narrow-profile belts for compact,
high-horsepower drives. Excellent in short-centered
drives or where high shock loads are present; can be used
any place you find traditional narrow V-belts, but require
a more robust composition for improved service life.
Key Features & Benefits
Introducing The Newest,
Longest-lasting Narrow V-Belt
in the Goodyear Engineered
Products Lineup
Constructed with a homogenous, one-piece design, the Wedge
TLP Narrow V-Belt delivers better, lasting performance. Its highmodulus, high-denier cord can handle a significant increase in
horsepower over our current HY-T® Wedge.
D u r ab i l i t y T h a t G o e s T h e
Distance
Wedge TLP belts offer supreme durability and wear resistance—
plus better fit even in worn sheaves. That’s all because of its two
envelope plies and specialty blended, fiber-rich compounding that
help support increased horsepower, with less deformation under
tension.
V - B E L T
Part No: 3V950
3V
0.38˝ Top Width — Narrow Profile
950
95.0˝ Nominal Outside Length
Envelope Uncogged Construction Shown
•Homogenous design
•Specialty blended, fiber rich compounding
•Higher modulus, higher denier cord
•Virtually no maintenance
•Static conductive*, with oil-resistant surface
•Supreme durability and wear resistance
Little Maintenance,
With No Worries
Wedge TLP’s unique advanced construction process includes use
of a specialized reinforcement and compounds that make this
narrow V-belt virtually maintenance free. Install this belt the first
time with proper installation techniques and take advantage of
reduced downtime and maintenance.
Increase Savings
Fewer Belts
by
Using
With its greater horsepower capacity, Wedge TLP allows you to
deliver the same amount of horsepower with a lesser number of
belts. Fewer belts mean fewer sheave grooves; the combination of
the two means lower-cost belt drives.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
59
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
0.38"
0.31"
0.62"
WEDGE TLP NARROW V-BELTS
™
3v
5
0.62" 0.38"
v
0.38"
0.31"
0.53"
0.31"
1.00"
0.53"
V - B E L T
Effective
Length (in)
100.0
106.0
112.0
118.0
Part
Number
3V1250
3V1320
3V1400
Effective
Length (in)
Part
Number
5V1180
5V1250
5V1320
5V1400
5V1500
5V1600
Effective
Length (in)
118.0
125.0
132.0
140.0
150.0
160.0
Part
Number
5V1700
5V1800
5V1900
5V2000
5V2120
5V2240
Effective
Length (in)
170.0
180.0
190.0
200.0
212.0
224.0
Part
Number
5V2360
5V2500
5V2650
5V2800
5V3000
5V3150
Effective
Length (in)
236.0
250.0
265.0
280.0
300.0
315.0
Part
Number
8V2000
8V2120
8V2240
8V2360
8V2500
Effective
Length (in)
200.0
212.0
224.0
236.0
250.0
Part
Number
8V2650
8V2800
8V3000
8V3150
8V3350
Effective
Length (in)
265.0
280.0
300.0
315.0
335.0
Part
Number
8V3550
8V3750
8V4000
8V4250
8V4500
Effective
Length (in)
355.0
375.0
400.0
425.0
450.0
Effective
Length (in)
80.0
85.0
90.0
95.0
100.0
106.0
112.0
Part
Number
8V1500
8V1600
8V1700
8V1800
8V1900
Effective
Length (in)
150.0
160.0
170.0
180.0
190.0
Part
Number
5V530*
5V560*
5V600*
5V630*
5V670*
5V710
5V750
Effective
Length (in)
53.0
56.0
60.0
63.0
67.0
71.0
75.0
Part
Number
8V1000
8V1120
8V1180
8V1250
8V1320
8V1400
Effective
Length (in)
100.0
112.0
118.0
125.0
132.0
140.0
1.00"
*Check customer service for availablitity. Size not produced at time of catalog printing.
60
0.91"
Part
Number
3V1000
3V1060
3V1120
3V1180
Part
Number
5V800
5V850
5V900
5V950
5V1000
5V1060
5V1120
Part
Number
3V630
3V670
0.91"
3V710
3V750
1.00"
Effective
Length (in)
80.0
85.0
90.0
95.0
Part
Number
3V800
3V850
0.91"
3V900
3V950
Effective
Length (in)
50.0
53.0
56.0
60.0
8v
0.62"
Effective
Length (in)
63.0
67.0
71.0
75.0
Part
Number
3V500
3V530
3V560
3V600
0.53"
125.0
132.0
140.0
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
HY - T W e d g e
®
A pp l i c a t i o n s
Narrow profile belts for compact, high horsepower
drives, high shock loading on short centers and small
diameters. For designing compact, heavy-duty drives
where space limitation is a factor.
Key Features & Benefits
A N a r r o w e r C r oss S e c t i o n
& Stronger Construction Reduces
D r i v e C os t s
The savings start in the basic wedge or narrow design of the HY-T
Wedge belt. It has a narrower cross section than standard V-belts
so it distributes stresses more uniformly to deliver more consistent,
more reliable power transmission.
A wedge cross section means the belts are narrower and weigh less.
Narrower belts allow for the use of thinner and lighter sheaves,
resulting in a more efficient drive.
The savings continue through the higher horsepower capacity
provided by Goodyear Engineered Products HY-T V-belt
construction. Vytacord tension members, provide strength and
dimensional stability. Higher horsepower capacity is also provided
through a tough engineered rubber compound cushion, adding to
belt strength.
HY-T Wedge, with its narrow cross-section, makes it possible to
achieve a required horsepower with fewer HY-T Wedge belts than
with standard V-belts, reducing sheave size, sheave costs, and belt
costs even more.
Since less power is required to run the smaller, lighter drives, more
power gets to the load. Therefore, you may be able to downsize
drive motors and/or increase drive efficiency for even more savings.
Matchmaker® Performance
HY-T Wedge belts eliminate mismatch problems as each
Matchmaker belt is mirrored in size and performance to every
other HY-T Wedge belt in that size, no matter when or where it
was produced.
C u t - E d g e o r E n v e l op e
Constructions Provide Optimum
Performance
HY-T Wedge belts are available in a cut-edge construction with
cogs for increased flexibility and heat dissipation or envelope
construction for drives where pulsation, shock loads, high tension,
and long centers are involved.
V - B E L T
Part No: 5V1400
5V
0.62˝ Top Width – Narrow Profile
1400 140.0˝ Nominal Outside Length
Envelope Uncogged Construction Shown
•Narrow profile provides savings through
efficiency.
•Greater horsepower than the classical belt.
•Strong Vytacord® (polyester) tensile members.
•High-grade engineered rubber.
•Heat, ozone, and abrasion resistant.
•Available in raw-edge construction with cogs or
envelope construction.
•Matchmaker® to eliminate mismatch.
•Static conductive.*
HY-T Wedge Cogged belts are high-horsepower belt constructions
that are identified with a 3VX and 5VX prefix and are available
in lengths up to 200˝. The cogged construction provides the
high flexibility required for short center distances. The cogs also
provide a larger surface area to dissipate heat and prolong belt
life. Improved material properties and advanced construction
technology results in an average horsepower increase of 30% over
standard “Classical” V-belt and wedge belts.
HY-T Wedge Envelope belts are identified with a 3V, 5V, or
8V prefix and are recommended for drives where pulsation,
shock loads, high tension, and long centers are involved. It
features a continuous V-section that is protected by a wide angle,
synthetic fabric impregnated with high-quality engineered rubber
compound. This unique envelope achieves the high strength
HY-T Wedge belts need to withstand high loading forces. It
also provides the torsional rigidity required in long center drives
delivering the traction needed for accurate tracking and precision
performance.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
61
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
0.38"
0.31"
HY - T W e d g e
0.53"
®
3vx
5
0.62" v0.38"
x
0.38"
0.31"
0.31"
0.53"
Cogged Sizes
V - B E L T
Part
Number
3VX250
3VX265
3VX280
3VX300
3VX315
3VX335
3VX355
Effective
Length (in)
25.0
26.5
28.0
30.0
31.5
33.5
35.5
Part
Number
3VX375
3VX400
0.91"
3VX425
3VX450
3VX475
3VX500
3VX530
Part
Number
5VX450
5VX470
5VX490
5VX500
5VX510
5VX530
5VX540
5VX550
5VX560
5VX570
5VX580
Effective
Length (in)
45.0
47.0
49.0
50.0
51.0
53.0
54.0
55.0
56.0
57.0
58.0
Part
Number
5VX590
5VX600
5VX610
5VX630
5VX650
5VX660
5VX670
5VX680
5VX690
5VX710
5VX730
1.00"
8vx
0.62"
0.53"
1.00"
0.91"
1.00"
Effective
Length (in)
37.5
40.0
42.5
45.0
47.5
50.0
53.0
Part
Number
3VX560
3VX600
0.91"
3VX630
3VX670
3VX710
3VX750
3VX800
Effective
Length (in)
59.0
60.0
61.0
63.0
65.0
66.0
67.0
68.0
69.0
71.0
73.0
Part
Number
5VX740
5VX750
5VX780
5VX800
5VX810
5VX830
5VX840
5VX850
5VX860
5VX880
5VX900
Effective
Length (in)
74.0
75.0
78.0
80.0
81.0
83.0
84.0
85.0
86.0
88.0
90.0
Part
Number
Effective
Length (in)
3V560
3V600
3V630
3V670
3V710
3V750
3V800
56.0
60.0
63.0
67.0
71.0
75.0
80.0
Part
Number
5V1250
5V1320
5V1400
5V1500
5V1600
5V1700
5V1800
Effective
Length (in)
125.0
132.0
140.0
150.0
160.0
170.0
180.0
Part
Number
Effective
Length (in)
8V2000
8V2120
8V2240
8V2360
8V2500
8V2650
200.0
212.0
224.0
236.0
250.0
265.0
0.62"
Effective
Length (in)
56.0
60.0
63.0
67.0
71.0
75.0
80.0
Effective
Part
Number Length (in)
3VX850
85.0
3VX900
90.0
3VX950
95.0
3VX1000
100.0
3VX1060
106.0
3VX1120
112.0
3VX1180
118.0
Effective
Part
Number Length (in)
5VX930
93.0
5VX950
95.0
5VX960
96.0
5VX1000
100.0
5VX1030
103.0
5VX1060
106.0
5VX1080
109.0
5VX1120
112.0
5VX1150
115.0
5VX1180
119.0
5VX1230
123.0
Effective
Part
Number Length (in)
3VX1250
125.0
3VX1320
132.0
3VX1400
140.0
3VX1500
150.0
Effective
Part
Number Length (in)
5VX1250
125.0
5VX1320
132.0
5VX1400
140.0
5VX1500
150.0
5VX1600
160.0
5VX1700
170.0
5VX1800
180.0
5VX1900
190.0
5VX2000
200.0
Noncogged Sizes
62
Part
Number
Effective
Length (in)
3V250
3V265
3V280
3V300
3V315
3V335
3V355
25.0
26.5
28.0
30.0
31.5
33.5
35.5
Part
Number
Effective
Length (in)
5V500
5V560
5V630
5V670
5V710
5V750
5V800
50.0
56.0
63.0
67.0
71.0
75.0
80.0
Part
Number
Effective
Length (in)
8V1000
8V1060
8V1120
8V1180
8V1250
8V1320
100.0
106.0
112.0
118.0
125.0
132.0
Part
Number
3V375
3V400
3V425
3V450
3V475
3V500
3V530
Part
Number
5V850
5V900
5V950
5V1000
5V1060
5V1120
5V1180
Part
Number
8V1400
8V1500
8V1600
8V1700
8V1800
8V1900
Effective
Length (in)
37.5
40.0
42.5
45.0
47.5
50.0
53.0
Effective
Length (in)
85.0
90.0
95.0
100.0
106.0
112.0
118.0
Effective
Length (in)
140.0
150.0
160.0
170.0
180.0
190.0
Part
Number
Effective
Length (in)
3V850
3V900
3V950
3V1000
3V1060
3V1120
3V1180
85.0
90.0
95.0
100.0
106.0
112.0
118.0
Part
Number
Effective
Length (in)
5V1900
5V2000
5V2120
5V2240
5V2360
5V2500
5V2650
190.0
200.0
212.0
224.0
236.0
250.0
265.0
Part
Number
Effective
Length (in)
8V2800
8V3000
8V3150
8V3350
8V3550
8V3750
280.0
300.0
315.0
335.0
355.0
375.0
Part
Number
3V1250
3V1320
3V1400
Part
Number
5V2800
5V3000
5V3150
5V3350
5V3550
Part
Number
8V4000
8V4250
8V4500
8V4750
8V5000
8V5600
Effective
Length (in)
125.0
132.0
140.0
Effective
Length (in)
280.0
300.0
315.0
335.0
355.0
Effective
Length (in)
400.0
425.0
450.0
475.0
500.0
560.0
P O W E R
T R A N S M I S S I O N
P R O D U C T S HY - T P l u s
®
V - B E L T
2 0 1 0
( C l a s s ic a l )
A pp l i c a t i o n s
Designed for operating at high speeds over small
diameter pulleys and short center distances. Also for
use in multiple V-belt drives where high shock load
and heavy-duty loads are encountered.
Key Features & Benefits
L e ss E l o n g a t i o n I s
to Performance
the
Key
Whether you’re talking about rubber belts or metal chains, most
materials will elongate when put to use. The secret to reliable
performance isn’t to eliminate elongation, but to control it so that
it is minimal, predictable, and uniform. To achieve these criteria,
we developed the Vytacord tensile member.
Vytacord provides the high-strength, high-horsepower rating
capacity needed to effectively transmit today’s drive power. It’s
even tough enough to tolerate slight sheave misalignment that
would quickly destroy ordinary belts.
The Vytacord tensile member provides dimensional stability.
As a result, each belt of a given size will maintain its length
consistency, no matter when or where it was produced.
The HY-T Plus’ envelope construction assures optimum warp and
fill thread angle, providing belt flexibility. In addition, the fabric is
treated with Goodyear Engineered Products exclusive engineered
rubber compound for long wear and resistance to heat, oil, and
other environmental hazards. The envelope also assures that the belt
dissipates static electricity, as specified in RMA bulletin IP3-3.
The cushion is also crush-resistant and cool running to maintain
its shape, fit, and strength longer. And with the longer service life
achieved by HY-T Plus belts, replacement of belts is less frequent.
Overall, belt costs are reduced, downtime is minimized, and
equipment productivity is maintained.
The exceptional dimensional stability properties of HY-T Plus
eliminates matching problems, improves performance, and
increases service life.
L e ss I n v e n t o r y R e q u i r e d
Improved Materials Are the
Key to the Durability &
V e r s a t i l i t y o f HY - T P l u s
The result is a reduced inventory that equates to dollars taken off
the shelves and into your pockets.
V - B E L T
Part No: B75
B
0.66˝ Top Width – Classical Profile
75
Approximate 75˝ Inside Length
•Universal classical profile.
•High-strength Vytacord® tensile members.
•Engineered rubber-impregnated envelope.
•Engineered rubber compound cushion
and insulation.
•Dual branded (Classical and FHP part numbers).
•Oil, heat, ozone, and abrasion resistant.
•Matchmaker to eliminate mismatch.
•Static conductive.*
The HY-T Plus can be used in FHP applications. Conversely, rarely
do FHP belts perform in HY-T Plus (classical) applications.
The vast improvements in all components of HY-T Plus
construction complement the quality of the Vytacord tensile
member.
Our engineered heat- and oil-resistant rubber compound, is used
in both the cushion and insulation sections of HY-T Plus. Belt
construction provides the flexibility on small pulleys. As a result
the belt is able to serve a dual purpose for both classical and FHP,
while offering more versatility than any other classical belt.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
To learn more visit www.goodyearep.com/ptp.
63
0.88"
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S 0.4
0.53"
HY - T P l u s
®
( C l a s s ic a l )
0.50"
0.31"
0.75"
A S e cti o n
Part Number
V - B E L T
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
Approx. Outside
Length (in)
(4L220)
(4L230)
(4L240)
(4L250)
(4L260)
(4L270)
(4L280)
(4L290)
(4L300)
(4L310)
(4L320)
(4L330)
(4L340)
(4L350)
(4L360)
(4L370)
(4L380)
(4L390)
(4L400)
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Part Number
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
Approx. Outside
Length (in)
(4L410)
(4L420)
(4L430)
(4L440)
(4L450)
(4L460)
(4L470)
(4L480)
(4L490)
(4L500)
(4L510)
(4L520)
(4L530)
(4L540)
(4L550)
(4L560)
(4L570)
(4L580)
(4L590)
41
42
43
44
45
45
47
48
49
50
51
52
53
54
55
56
57
58
59
Part Number
A58
A59
A60
A61
A62
A63
A64
A65
A66
A67
A68
A69
A70
A71
A72
A73
A74
A75
A76
Approx. Outside
Length (in)
(4L600)
(4L610)
(4L620)
(4L630)
(4L640)
(4L650)
(4L660)
(4L670)
(4L680)
(4L690)
(4L700)
(4L710)
(4L720)
(4L730)
(4L740)
(4L750)
(4L760)
(4L770)
(4L780)
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
Part Number
A77
A78
A79
A80
A81
A82
A83
A84
A85
A86
A87
A88
A89
A90
A91
A92
A93
A94
A95
Approx. Outside
Length (in)
(4L790)
(4L800)
(4L810)
(4L820)
(4L830)
(4L840)
(4L850)
(4L860)
(4L870)
(4L880)
(4L890)
(4L900)
(4L910)
(4L920)
(4L930)
(4L940)
(4L950)
(4L960)
(4L970)
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
Part Number
1.5"
Approx. Outside
Length (in)
A96 (4L980)
A97 (4L990)
A98 0.91"
(4L1000)
A100 (4L1020)
A103
A105 A110
A112
A120
A128
A133
A136
A144
A158
A173 A180
98
99
100
102
105
107
112
114
122
130
135
138
146
160
175
182
0.66"
0.88"
0.41"
0.53"
B S e cti o n
Part Number
64
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
Approx. Outside
Length (in)
(5L250)
(5L260)
(5L270)
(5L280)
(5L290)
(5L300)
(5L310)
(5L320)
(5L330)
(5L340)
(5L350)
(5L360)
(5L370)
(5L380)
(5L390)
(5L400)
(5L410)
(5L420)
(5L430)
(5L440)
(5L450)
(5L460)
(5L470)
(5L480)
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Part Number
B46
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
B63
B64
B65
B66
B67
B68
B69
Approx. Outside
Length (in)
(5L490)
(5L500)
(5L510)
(5L520)
(5L530)
(5L540)
(5L550)
(5L560)
(5L570)
(5L580)
(5L590)
(5L600)
(5L610)
(5L620)
(5L630)
(5L640)
(5L650)
(5L660)
(5L670)
(5L680)
(5L690)
(5L700)
(5L710)
(5L720)
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
Part Number
B70
B71
B72
B73
B74
B75
B76
B77
B78
B79
B80
B81
B82
B83
B84
B85
B86
B87
B88
B89
B90
B91
B92
B93
Approx. Outside
Length (in)
(5L730)
(5L740)
(5L750)
(5L760)
(5L770)
(5L780)
(5L790)
(5L800)
(5L810)
(5L820)
(5L830)
(5L840)
(5L850)
(5L860)
(5L870)
(5L880)
(5L890)
(5L900)
(5L910)
(5L920)
(5L930)
(5L940)
(5L950)
(5L960)
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
Part Number
Approx. Outside
Length (in)
B94 (5L970) 97
B95 0.50"
(5L980) 98
B96 (5L990) 99
0.31"
B97 (5L1000) 100
0.75"
B98 (5L1010) 101
B99 (5L1020) 102
B100 103
B101 1.5"104
B103 106
B104 107
B105 108
B108 111
0.91"
B111 114
B112 115
B115 118
B116 119
B118 121
B120 123
B124 127
B126 129
B128 131
B133 136
B136 139
B140 143
Part Number
B144 B148 B150 B154 B158 B162 B173 B180 B190 B195 B205 B210 B225 B240 B255 B270 B285 B300 B315 B330 B360 B394 Approx. Outside
1.25" Length (in)
147
151
153
157
161
165
176
183
193
198
208
213
227
242
257
272
287
302
317
332
362
396
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S HY - T P l u s
®
2 0 1 0
( C l a s s ic a l )
0.66
0.88"
C S e cti o n
Part Number
Approx. Outside
Length (in)
C48
C50
C51
C55
C60
C62
C68
C71
C72
C75
C78
52
54
55
59
64
66
72
75
76
79
82
0.41"
0.53"
Part Number
Approx. Outside
Length (in)
C80
C81
C85
C90
C93
C94
C100
C101
C103
C105
C106
84
85
89
94
97
98
104
105
107
109
110
Part Number
Approx. Outside
Length (in)
C108
C109
C110
C112
C115
C120
C124
C128
C136
C144
C148
112
113
114
116
119
124
128
132
140
148
152
Part Number
Approx. Outside
Length (in)
C150
C156
C158
C162
C165
C173
C180
C190
C195
C210
C225
Part Number
154
160
162
166
169
177
184
194
199 0.88"
214
227
0.53"
Approx. Outside
Length (in)
C2400.50"
C255
C270
0.31"
C285
C300
C315
C330
C345
C360
C390
0.91"
C420
0.41"
1.25"
242
257
272
287 0.75"
302
317
332
1.5"
347
362
0.66"
392
422
0.66"
1.25"
0.88"
D S e cti o n
Part Number
D112
D120
D128
D144
D158
Approx. Outside
Length (in)
117
125
133
149
163
Part Number
D162
D173
D180
D195
D210
Approx. Outside
Length (in)
167
178
185
200
215
Part Number
D225
D240
D255
D270
D285
Approx. Outside
Length (in)
228
243
258
273
388
Part Number
D300
D315
0.91"
D330
D345
D360
0.41"
0.53"
0.75"
0.31"
1.5"
Approx. Outside
Length (in)
303
318
333
348
363
Approx. Outside
Length (in)
Part Number
0.31"
0.50"
D390
V - B E L T
0.50"
1.25"
393
423
453
0.75"
483
543
D420
D450
D480
D540
1.5"
0.91"
E S e cti o n
Part Number
E180
E195
E210
Approx. Outside
Length (in)
187
202
217
Part Number
E240
E270
E300
Approx. Outside
Length (in)
244
274
304
Part Number
E330
E360
E390
Approx. Outside
Length (in)
334
364
394
Part Number
E420
E480
E540
Approx. Outside
Length (in)
424
484
544
Part Number
E600
Approx. Outside
Length (in)
604
65
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S Torque-Flex
®
A pp l i c a t i o n s
Designed for the tough, small sheave, high-tension
drives.
Key Features & Benefits
•Premium classical profile construction.
•25% – 30% higher power ratings than standard
V-belts.
•Strong Vytacord® (polyester) tensile members.
•Engineered cushion compound.
•Cut-edge cogged construction on most sizes.
•Heat, ozone, and abrasion resistant.
•Matchmaker® to eliminate mismatch.
•Static conductive.*
Part No: BX75
B
0.66˝ Top Width – Classical Profile
X
Premium Cogged Construction
75
Approximate 75˝ Inside Length
Cut-Edge, Molded Cog Construction Shown
M o r e H o r s e po w e r
per
Dollar
More Savings From Fewer Belts
V - B E L T
Your drives can deliver the horsepower you want at a lower
component cost—and with lower energy costs—when
you include Goodyear Engineered Products Torque-Flex
V-belts in the design.
The high-strength and high horsepower capacity of Torque-Flex
V-belts means you need fewer belts and fewer sheave grooves to
deliver the same amount of horsepower.
They are fully cogged to provide the flexibility needed to
keep their high-traction rubber edges in contact with the
sheave grooves. This high efficiency allows you to achieve the
horsepower you need at a lower total drive cost.
Energy-Saving Efficiency
Exacting Precision & Uniformity
The same design and construction features which lead to
high horsepower ratings for Torque-Flex V-Belts also lead to
improvements in energy efficiency of up to 4%, depending on
sheave diameter.
COGGED VS. NONCOGGED BELT EFFICIENCY
Rigid quality assurance programs imposed during Torque-Flex
V-belt manufacture result in belt angles and belt lengths which
are more exact than standard belts. This results in quiet, smoothrunning, and long-lasting belts. Think what that can save in
reduced downtime and belt maintenance.
• You eliminate mismatching problems caused by individual belts that may be too loose or too tight.
• You simplify ordering procedures—no lengthy specifications, detailing match-ups, and sizing.
• No complicated time-consuming matching. Your Goodyear Engineered Products belts are automatically matched
when you buy them.
• You reduce your in-plant inventory. The Matchmaker system covers your needs with a minimum of belts to
save you space and inventory dollars.
*Drive conditions and service variables in combination with time in operation
can result in a loss of static conductivity. It is recommended that a conductivity
check be added to drive preventive maintenance programs where belt static
conductivity is a requirement.
66
COGGED
96
Efficiency, %
Of course, with such exacting production requirements, our
Torque-Flex V-belts also achieve consistent uniformity from
run to run. This outstanding consistency means you can be
sure that two belts of the same size designation will match, no
matter when they were produced. As a result:
98
94
NONCOGGED
92
90
88
2
3
4
5
6
7
Sheave Diameter, Inches
8
9
T R A N S M I S S I O N
V - B E L T
P R O D U C T S Torque-Flex
0.50"
0.31"
Side View
BX28
BX31
BX32
BX34
BX35
BX36
BX38
BX40
BX41
BX42
BX43
BX44
BX45
BX46
BX47
BX48
BX49
BX50
BX51
BX52
31
34
35
37
38
39
41
43
44
45
46
47
48
49
50
51
52
53
54
55
CX51
CX55
CX60
CX68
CX72
CX75
CX78
55
59
64
72
76
79
82
BX53
BX54
BX55
BX56
BX57
BX58
BX59
BX60
BX61
BX62
BX63
BX64
BX65
BX66
BX67
BX68
BX69
BX70
BX71
BX72
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
CX81
CX85
CX90
CX96
CX100
CX101
CX105
85
89
94
100
104
105
109
Approx.
Part
Outside
Number Length (in)
AX56
58
AX57
59
AX58
60
AX59
61
AX60
62
AX61
63
AX62
64
AX63
65
AX64
66
AX65
67
AX66
68
AX67
69
AX68
70
AX69
71
AX70
72
AX71
73
AX72
74
bx
Approx.
Part
Outside
Number Length (in)
AX73
75
AX74
76
AX75
77
AX76
78
AX77
79
AX78
80
AX79
81
AX80
82
AX81
83
AX82
84
AX83
85
AX84
86
AX85
87
AX86
88
AX87
89
AX88
90
AX89
91
BX73
BX74
BX75
BX76
BX77
BX78
BX79
BX80
BX81
BX82
BX83
BX84
BX85
BX86
BX87
BX88
BX89
BX90
BX91
BX92
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
CX109
CX111
CX112
CX115
CX120
CX128
CX136
113
115
116
119
124
132
140
cx
Approx.
Part
Outside
Number Length (in)
AX90
92
AX91
93
AX93
95
AX94
96
AX95
97
AX96
98
AX97
99
AX98
100
AX100
102
AX103
105
AX105
107
AX110
112
AX112
114
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
BX93
BX94
BX95
BX96
BX97
BX98
BX99
BX100
BX103
BX105
BX106
BX108
BX112
BX113
BX115
BX116
BX120
BX123
BX124
BX126
96
97
98
99
100
101
102
103
106
108
109
111
115
116
118
119
123
126
127
129
CX144
CX150
CX158
CX162
CX173
CX180
CX195
148
154
162
166
177
184
199
BX128
BX133
BX136
BX140
BX144
BX148
BX150
BX154
BX158
BX162
BX173
BX180
BX191
BX195
BX210
BX225
BX240
BX255
BX270
BX300
131
136
139
143
147
151
153
157
161
165
176
183
194
198
213
228
243
258
273
303
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
0.31" 0.31"
0.41" 0.41"
0.53" 0.53"
0.41"
0.53"
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
®
0.50" 0.50"
0.66" 0.66"0.88" 0.88" 0.88"
0.66"
ax
Approx.
0.50" Approx.
Part
0.88"
Outside
Outside 0.66" Part
Number Length (in)
Number Length (in)
0.31"
AX39
41
AX21
23
0.41"
0.53"
AX40
42
AX22
24
AX41
43
AX23
25
AX42
44
AX24
26
AX43
45
AX26
28
AX44
46
AX27
29
AX45
47
AX28
30
AX46
48
AX29
31
AX47
49
AX30
32
AX48
50
AX31
33
AX49
51
AX32
34
AX50
52
AX33
35
AX51
53
AX34
36
AX52
54
AX35
37
AX53
55
AX36
38
AX54
56
AX37
39
AX55
57
AX38
40
2 0 1 0
V - B E L T
P O W E R
CX210
CX240
CX270
214
244
274
67
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S GY M e t r ic B e l t s
®
A pp l i c a t i o n s
Specialty V-belt for a wide variety of heavy-duty,
temperature-sensitive applications.
Key Features & Benefits
•Wedge profile allows for a smaller drive package
and lower operating costs.
•Premium fiber loading adds strength and
cord support.
•Raw-edge, molded cog and envelope constructions.
•Optimum wedging action provides maximum
torque carrying performance.
•Heat, ozone and abrasion resistant.
•Static-conductive** for specialized applications.
Part No: XPA0707
X
Premium Cogged Construction
PA
Metric A Profile
0707 707mm Datum Length
Versatility
V - B E L T
GY Metric belts operate under one of the widest temperature
ranges in the industry, from -65°F to 180°F (-54°C to 82°C)*. It’s
that versatility and our experience in rubber compounding that
can provide superior performance under the toughest conditions.
Superior Performance Under
Tough Conditions
GY Metric belts are strong, flexible and able to work within a
wide temperature range, offering superior performance under
the toughest conditions. So they do more than measure up.
They stand apart.
Universal Fit
When equipment calls for metric precision, you need a belt that
not only measures up, but one that won’t get lost in translation.
GY Metric belts are engineered to universal metric profiles, but
manufactured by Veyance Technologies in North America, so you
don’t have to go elsewhere to get them.
More Savings From Fewer Belts
The high-strength and high horsepower capacity of Torque-Flex®
V-belts means you need fewer belts and fewer sheave grooves to
deliver the same amount of horsepower.
*Temperature range is based upon test data obtained on select belt sizes manufactured from our latest rubber compounds, consistent with standard MIL-B11040-E, section 3.8.
**Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity
check be added to drive preventive maintenance programs where belt static conductivity is a requirement.
To learn more visit www.goodyearep.com/ptp.
68
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
GY M e t r ic B e l t s
®
Part Number Eff. Length (in)
XPZ0487
0.077
XPZ0512
0.081
XPZ0562
0.088
XPZ0587
0.091
XPZ0612
0.094
XPZ0630
0.097
XPZ0637
0.098
XPZ0662
0.102
XPZ0670
0.103
XPZ0687
0.105
XPZ0710
0.109
XPZ0722
0.111
XPZ0737
0.113
XPZ0750
0.114
XPZ0762
0.116
XPZ0787
0.120
XPZ0800
0.122
XPZ0812
0.124
XPZ0825
0.125
XPZ0837
0.127
XPZ0850
0.129
XPZ0862
0.131
XPZ0875
0.133
XPZ0887
0.135
Part Number Eff. Length (in)
XPZ0900
0.136
XPZ0912
0.138
XPZ0922
0.139
XPZ0925
0.140
XPZ0927
0.140
XPZ0937
0.142
XPZ0950
0.144
XPZ0962
0.146
XPZ0975
0.147
XPZ0987
0.148
0.151
XPZ1000
XPZ1012
0.152
XPZ1024
0.154
XPZ1037
0.156
XPZ1047
0.158
XPZ1060
0.159
XPZ1077
0.163
XPZ1087
0.163
XPZ1112
0.167
XPZ1120
0.168
XPZ1137
0.170
XPZ1162
0.174
XPZ1171
0.175
XPZ1180
0.177
Part Number Eff. Length (in)
XPZ1187
0.178
XPZ1200
0.180
XPZ1202
0.180
XPZ1237
0.185
XPZ1250
0.187
XPZ1262
0.189
XPZ1270
0.190
XPZ1287
0.192
XPZ1312
0.196
XPZ1320
0.197
XPZ1337
0.200
0.203
XPZ1362
XPZ1387
0.206
0.209
XPZ1400
XPZ1412
0.210
XPZ1420
0.212
XPZ1437
0.214
0.215
XPZ1450
XPZ1462
0.217
XPZ1487
0.221
0.223
XPZ1500
XPZ1512
0.225
XPZ1520
0.226
XPZ1527
0.227
Part Number Eff. Length (in)
XPZ1537
0.228
XPZ1562
0.232
XPZ1587
0.236
XPZ1600
0.237
XPZ1612
0.239
XPZ1637
0.243
XPZ1650
0.245
XPZ1662
0.247
XPZ1687
0.250
XPZ1700
0.252
XPZ1737
0.258
XPZ1750
0.259
XPZ1762
0.261
XPZ1787
0.264
XPZ1800
0.267
0.268
XPZ1812
XPZ1837
0.271
XPZ1850
0.273
XPZ1862
0.275
XPZ1887
0.279
XPZ1900
0.281
XPZ1937
0.286
XPZ1950
0.288
XPZ1962
0.290
Part Number Eff. Length (in)
XPZ1987
0.293
XPZ2000
0.295
XPZ2030
0.300
XPZ2037
0.301
XPZ2060
0.303
XPZ2062
0.305
XPZ2075
0.306
XPZ2087
0.308
0.313
XPZ2120
XPZ2160
0.318
XPZ2187
0.322
0.330
XPZ2240
XPZ2280
0.336
XPZ2287
0.337
XPZ2360
0.348
XPZ2410
0.355
XPZ2487
0.366
XPZ2500
0.368
XPZ2540
0.373
XPZ2650
0.389
XPZ2800
0.411
Part Number Eff. Length (in)
XPA1232
0.318
XPA1250
0.323
XPA1257
0.325
XPA1282
0.331
XPA1300
0.335
XPA1307
0.337
XPA1320
0.340
XPA1325
0.342
XPA1332
0.343
XPA1357
0.350
XPA1382
0.354
XPA1400
0.359
XPA1407
0.360
XPA1432
0.367
XPA1450
0.371
XPA1457
0.371
XPA1482
0.379
XPA1500
0.384
XPA1507
0.385
XPA1525
0.390
XPA1532
0.392
XPA1550
0.396
Part Number Eff. Length (in)
XPA1557
0.398
0.404
XPA1582
XPA1600
0.409
XPA1607
0.410
XPA1632
0.416
XPA1657
0.423
XPA1682
0.429
XPA1700
0.434
XPA1707
0.435
XPA1732
0.442
XPA1750
0.444
XPA1757
0.448
XPA1782
0.452
XPA1800
0.457
XPA1807
0.459
XPA1832
0.465
XPA1850
0.470
XPA1857
0.471
XPA1882
0.477
XPA1900
0.482
XPA1907
0.484
XPA1932
0.490
Part Number Eff. Length (in)
XPA1957
0.496
XPA1982
0.502
XPA2000
0.507
XPA2032
0.515
XPA2057
0.521
XPA2060
0.522
XPA2082
0.527
XPA2120
0.536
XPA2132
0.540
XPA2182
0.550
XPA2207
0.557
XPA2240
0.566
XPA2282
0.575
XPA2300
0.580
XPA2360
0.594
XPA2432
0.613
XPA2482
0.625
XPA2500
0.630
XPA2532
0.638
XPA2580
0.649
XPA2582
0.650
XPA2607
0.655
Part Number Eff. Length (in)
XPA2632
0.661
XPA2650
0.666
XPA2682
0.673
XPA2732
0.686
XPA2782
0.698
XPA2800
0.703
XPA2832
0.711
XPA2882
0.723
XPA2900
0.728
XPA2982
0.747
XPA3000
0.751
XPA3150
0.789
XPA3182
0.797
XPA3350
0.837
XPA3382
0.847
SPA3550
1.018
SPA3650
1.047
SPA3882
1.112
SPA4000
1.145
SPA4500
1.287
V - B E L T
XPZ*
XPA*/SPA
Part Number Eff. Length (in)
XPA0707
0.189
XPA0732
0.195
XPA0757
0.202
XPA0782
0.208
XPA0850
0.225
XPA0857
0.227
XPA0872
0.230
0.233
XPA0882
XPA0900
0.237
XPA0922
0.242
XPA0982
0.256
XPA1000
0.261
XPA1007
0.262
XPA1032
0.269
XPA1057
0.275
XPA1060
0.276
XPA1082
0.281
XPA1120
0.290
XPA1157
0.300
XPA1180
0.306
XPA1207
0.312
XPA1220
0.315
*Denotes cog construction.
69
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S GY M e t r ic B e l t s
®
XPB*/SPB
Part Number Eff. Length (in)
XPB1250
0.432
XPB1320
0.455
XPB1340
0.461
XPB1400
0.482
XPB1410
0.484
XPB1450
0.499
XPB1500
0.513
XPB1550
0.530
XPB1600
0.547
XPB1650
0.563
XPB1700
0.580
XPB1778
0.605
XPB1800
0.614
XPB1850
0.631
Part Number Eff. Length (in)
XPB2410
0.815
XPB2430
0.821
XPB2500
0.844
XPB2530
0.855
XPB2580
0.871
XPB2600
0.878
XPB2650
0.894
XPB2680
0.903
XPB2720
0.917
XPB2800
0.943
XPB2820
0.949
XPB2840
0.957
XPB2900
0.976
XPB3000
1.010
Part Number Eff. Length (in)
XPB3150
1.060
XPB3170
1.064
XPB3320
1.116
XPB3340
1.123
XPB3350
1.125
XPB3450
1.158
XPB3550
1.192
SPB3650
1.730
SPB3750
1.777
SPB3800
1.800
SPB3870
1.833
SPB4000
1.894
SPB4250
2.010
SPB4500
2.127
Part Number Eff. Length (in)
SPB4560
2.155
SPB4620
2.183
SPB4750
2.244
SPB4820
2.276
SPB5000
2.360
SPB5300
2.500
SPB5600
2.640
SPB6000
2.827
SPB8000
3.760
SPB9000
4.227
Part Number Eff. Length (in)
XPC2650
1.840
XPC2800
1.938
XPC3000
2.074
XPC3150
2.176
2.308
XPC3350
Part Number Eff. Length (in)
XPC3550
2.440
SPC3750
3.466
SPC4000
3.694
SPC4250
3.919
SPC4500
4.147
Part Number Eff. Length (in)
SPC4750
4.374
SPC5000
4.600
SPC5300
4.874
SPC5600
5.146
SPC6000
5.510
Part Number Eff. Length (in)
SPC6700
6.147
SPC7100
6.510
SPC7500
6.874
SPC8000
7.329
V - B E L T
Part Number Eff. Length (in)
XPB1900
0.645
XPB1950
0.662
XPB2000
0.679
XPB2020
0.685
XPB2060
0.700
XPB2120
0.718
XPB2150
0.729
XPB2180
0.739
XPB2240
0.758
XPB2264
0.767
XPB2280
0.771
XPB2300
0.777
XPB2310
0.781
XPB2360
0.798
XPC*/SPC
Part Number Eff. Length (in)
XPC1047
0.765
1.483
XPC2120
XPC2240
1.564
XPC2360
1.645
XPC2500
1.738
*Denotes cog construction.
70
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
Hex
A pp l i c a t i o n s
Used on drives having one or more reverse bends and
usually where power must be transmitted to or from the
belt in both the usual and reverse positions.
•Lawn and Garden Equipment • Mixers
•Agitators
• Mule Drives
•Conveyors
• Crushers
Key Features & Benefits
Part No: BB75
BB
B Section Double
Classical Profile 0.66˝ Center Width
75
Approximate 75˝ Inside Length
Dependable Power From Both Sides
•Dual-sided classical profile.
•High-strength Vytacord® tensile members.
•Engineered rubber compound-impregnated envelope.
•Engineered rubber cushion and insulation.
•Oil, heat, ozone, and abrasion resistant.
•Static conductive.*
To meet the multiple-bend and dual-power requirements, we build
Hex belts with rugged Vytacord tension members. They deliver
maximum strength with minimum elongation. They also work with
all the other quality materials that are a part of our Hex belts to
deliver maximum performance over a long, trouble-free life.
V - B E L T
Hex belts, also known as double V-belts, are designed for use on
drives with one or more reverse bends. They usually transmit power
from both sides of the belt.
Hex belts are available in AA, BB, and CC cross sections. A special
Dry Can Hex construction is available with a special deep CC cross
section designated CCP.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
To learn more visit www.goodyearep.com/ptp.
71
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
Hex
AA
0.50"
0.41"
0.96"
BB
0.50"
0.66"
0.66"
0.53"
0.86"
0.96"
V - B E L T
0.86"
0.50"
0.41"
0.66"
0.53"
CC75
CC81
0.86"
CC85
CC90
CC96
CC105
CC112
72
Approx.
0.86"
Outside
Length (in)
81.4
87.4
91.4
96.4
102.4
111.4
118.4
CCP240
CCP255
CCP270
CCP300
CCP330
CCP360
CCP390
244.9
259.9
274.9
304.9
334.9
364.9
394.9
Part
Number
Approx.
Outside
Length (in)
AA68
AA70
AA75
AA80
AA85
71.4
73.4
78.4
83.4
88.4
Part
Number
Approx.
Outside
Length (in)
BB83
BB85
BB90
BB92
BB93
BB94
BB96
BB97
BB103
BB105
BB107
BB108
BB111
BB112
BB116
BB117
BB118
87.6
89.6
94.6
96.6
97.6
98.6
100.6
101.6
107.6
109.6
111.6
112.6
115.6
116.6
120.6
121.6
122.6
Part
Number
Approx.
Part
Outside
Number Length (in)
0.86"
0.86"
54.4
58.4
63.4
67.4
69.4
Approx.
Part
Outside
Number0.86"Length (in)
CCP
0.96"
AA51
AA55
0.53"
AA60
AA64
AA66
0.86"
BB35
39.6
BB38
42.6
BB42
46.6
BB43
47.6
BB45
49.6
BB46
50.6
BB53
57.6
BB55
59.6
BB60
64.6
BB64
68.6
BB68
72.6
BB71
75.6
BB72
76.6
BB73 0.66" 77.6
BB74
78.6
BB75
79.6
0.53"
BB81
85.6
0.96"
0.50"
Approx.
Outside
Length
0.66" (in)
Part
Number
CC
0.66"
Part
Number
CC120
CC128
CC136
CC144
CC148
CC158
CC162
Part
Number
Part
Number
Approx.
Outside
Length (in)
126.4
134.4
142.4
150.4
154.4
164.4
168.4
CCP408
CCP420
CCP440
CCP450
CCP470
CCP480
CCP540
412.9
424.9
444.9
454.9
474.9
484.9
544.9
93.4
95.4
99.4
108.4
115.4
Approx.
Outside
Length (in)
BB120
BB122
BB123
BB124
BB128
BB129
BB130
BB136
BB140
BB144
BB155
BB158
BB162
BB168
BB169
BB173
BB180
124.6
126.6
127.6
128.6
132.6
133.6
134.6
140.6
144.6
148.6
159.6
162.6
166.6
172.6
173.6
177.6
184.6
Part
Number
Approx.
Outside
Length (in)
CC173
CC180
CC195
CC210
CC225
CC240
CC255
179.4
186.4
201.4
216.4
229.4
244.4
259.4
CCP550
CCP578
CCP600
CCP640
CCP660
CCP670
CCP680
554.9
582.9
604.9
644.9
664.9
674.9
684.9
AA120
AA128
123.4
131.4
Approx.
Part
Outside
Number Length
(in)
BB182
BB190
BB195
BB210
BB225
BB226
BB228
BB230
BB240
BB255
BB267
BB270
BB273
BB277
BB278
BB285
BB300
186.6
194.6
199.6
214.6
228.1
229.1
231.1
233.1
243.1
258.1
270.1
273.1
276.1
280.1
281.1
288.1
308.1
Approx.
Part
Outside
Number Length (in)
CC270
CC300
CC330
CC360
CC390
CC420
274.4
304.4
334.4
364.4
394.4
424.4
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
Approx.
Part
Outside
Number Length (in)
AA90
AA92
AA96
AA105
AA112
Approx.
Part
Outside
Number Length (in)
Approx.
Outside
Length (in)
CCP700
CCP720
CCP750
CCP780
CCP800
CCP840
CCP900
704.9
724.9
754.9
784.9
804.9
844.9
904.9
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S I nsta -P owe r
®
2 0 1 0
(F lexten ® C lassical )
A pp l i c a t i o n s
Delivers high performance consistently in lawn and
garden drives up to 20 horsepower. Also ideal for
other power equipment where reverse bend idlers,
misalignment, and quarter-turn drives cause ordinary
belts to fail.
Key Features & Benefits
Part No: 84310
84
Top Width Designation: 84 denotes 4⁄ 8 ˝ top width
31
Length in Inches
0
Tenths of an Inch
A29F — Equivalent Classical Size
for
Strength & Endurance
Every element of the Insta-Power belt is designed to deliver
premium, long-life performance in demanding outdoor power
equipment service. Insta-Power belts are engineered to take the
abuse of repeated sudden shock loads, tolerate high ambient
temperatures, and resist the damaging effects of oil and dust.
0.50"
The fabric cover on Insta-Power belts is impregnated with our
exclusive0.66"
engineered rubber compound for high-wear, abrasion,
and oil resistance. It also resists drying and cracking, even at high
temperatures. The compression section is specially compounded
0.41"
to provided the excellent flexibility required for a wide variety of
high-stress drives. The load carrying tensile members are highstrength Flexten cable cord with proven reliability in lawn and
garden applications.
0.50"
0.38"
0.22"
0.31"
8 3 (3⁄8˝ )
3l
s e cti o n
83160*
83170
83180
83190
83200
83210
0.31"
0.41"
4 l0.88"
s e cti o n
83220*
83225*
83230*
83235*
83240
83245*
83250
83255
83260*
83270
83280
83290*
0.41"
8 7 ( 7⁄8˝ )
b s e cti o n
c s e cti o n
o r0.38"
5 l s e cti o n
Instapower
83295
83300
83310
83315
83320
83330
0.2
0.53"
8 5 (5⁄8˝ )
0.22"
0.53"
0.41
0.88"
0.66"
0.38"
0.88"
Instapower 0.53"
Instapower
Instapower
0.66"
a s e cti o n
or
83 3l
0.50"
8 4 (4⁄8˝ )
s e cti o n
0.31"
V - B E L T
Built
•Flexten classical profile construction.
•High-strength Flexten tensile members.
•Engineered rubber cushion compound.
•Premium envelope construction.
•Triple part number branding (Insta-Power,
Classical, and Fraction horsepower).
•Oil, heat, ozone, and abrasion resistant.
•Static conductive.**
0.22"
Instapower
83340
83350
83360
83370*
83375
83380
Instapower
83390
83400
83410
83415
83420
83430
Instapower
83440
83450
83460
83470
83480
83490
Instapower
83500
83510
83560
83570
83610
*Cut-edge construction.
**Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
For sizes not listed, contact Veyance customer service for construction.
73
P O W E R
T R A N S M I S S I O N
I nsta -P ower
84
a s e cti o n o r
Flexten
Instapower Classical
84170
A15F
84180
A16F
84190
A17F
A18F
84200
84210
A19F
84220
A20F
84230
A21F
A22F
84240
84250
A23F
84255
84260
A24F
84270
A25F
84275
84280
A26F
84285
84290
A27F
84295
85
V - B E L T
85240
85250
85260
85270
85280
85290
85300
85310
85320
85330
85335
85340
85350
87
5l
Flexten
Instapower Classical
84385
84390
A37F
84400
A38F
84405
84410
A39F
84415
84420
A40F
84425
84430
A41F
84440
A42F
84450
A43F
A44F
84460
84470
A45F
84475
84480
A46F
84485
84490
A47F
85360
85370
85380
85390
85400
85410
85420
85430
85440
85450
85460
85470
85480
B31F
B32F
(F lexten ® C lassical )
Flexten
Instapower Classical Instapower Flexten
Classical
84670
A65F
84500
A48F
84680
A66F
84510
A49F
84690
A67F
84520
A50F
84700
A68F
A51F
84530
84710
A69F
84540
A52F
84720
A70F
84550
A53F
84730
A71F
84560
A54F
84740
A72F
84570
A55F
84750
A73F
A56F
84580
84760
A74F
84590
A57F
84770
A75F
84600
A58F
84780
A76F
84610
A59F
84790
A77F
84620
A60F
84800
A78F
A61F
84630
84810
A79F
84640
A62F
A80F
84820
84650
A63F
A81F
84830
84660
A64F
Flexten
Instapower Classical
84840
A82F
84850
A83F
A84F
84860
84870
A85F
84880
A86F
84890
A87F
84900
A88F
A89F
84910
84920
A90F
84930
A91F
84940
A92F
84950
A93F
A94F
84960
84970
A95F
84980
A96F
84990
A97F
A98F
84999
Flexten
Instapower Classical Instapower Flexten
Classical
Flexten
Instapower Classical
s e cti o n
Flexten
Instapower Classical
B21F
B22F
B23F
B24F
B25F
B26F
B27F
B28F
B29F
B30F
®
s e cti o n
Flexten
Instapower Classical
84300
A28F
84305
84310
A29F
84315
84320
A30F
84325
84330
A31F
84335
84340
A32F
84345
84350
A33F
84355
84360
A34F
84365
84370
A35F
84375
84380
A36F
b s e cti o n o r
Flexten
Instapower Classical
4l
V - B E L T
P R O D U C T S Flexten
Instapower Classical
85490
85500
85510
85520
85530
85540
85550
85560
85570
85580
85590
85600
85610
B33F
B34F
B35F
B36F
B37F
B38F
B39F
B40F
B41F
B42F
B43F
B44F
B45F
85620
85630
85640
85650
85660
85670
85680
85690
85700
85710
85720
85730
85740
B46F
B47F
B48F
B49F
B50F
B51F
B52F
B53F
B54F
B55F
B56F
B57F
B58F
B59F
B60F
B61F
B62F
B63F
B64F
B65F
B66F
B67F
B68F
B69F
B70F
B71F
85750
85760
85770
85780
85790
58800
85810
85820
85830
85540
85850
85860
85870
85880
85890
85900
85910
85920
85930
85940
85950
85960
85970
85980
85990
85999
B72F
B73F
B74F
B75F
B76F
B77F
B78F
B79F
B80F
B81F
B82F
B83F
B84F
B85F
B86F
B87F
B88F
B89F
B90F
B91F
B92F
B93F
B94F
B95F
B96F
B97F
c s e cti o n
Flexten
Instapower Classical
87720
87790
C68F
C75F
Flexten
Instapower Classical
87850
87890
Flexten
Instapower Classical
C81F
C85F
87940
871000
Flexten
Instapower Classical Instapower Flexten
Classical
C90F
C96F
871040 871090
C100F
C105F
871160
871240
Flexten
Instapower Classical
C112F
C120F
871320
C128F
89
Instapower
89002*
89003
89007
89009
89101*
89102*
89103*
89104*
Instapower
89105*
89106*
89201*
89202*
89203*
89204
89205
89206
Instapower
89207
89208*
89209*
89210*
89211*
89212*
89213
89214
Instapower
89215
89216*
89217*
89218
89219
89220
89221*
89222
Instapower
89223
89224
89225
89226
89227
89228
89229
89230
Instapower
89231
89232
89233*
89234*
89235*
89236
89237*
89238
Instapower
*Cut edge construction.
For sizes not listed, contact Veyance customer service for construction.
74
89239*
89240
89241
89242*
89243
89244*
89245*
89246*
Instapower
89247
89248
89249
89250
89251
89253
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S 2 0 1 0
FH P
A pp l i c a t i o n s
For light-duty fractional horsepower motors. Molded
cogs allow for use in applications where the belt is
expected to perform around smaller sheave diameters.
•Shop Equipment
• Home Appliances
•Light-Duty Machinery
• Blowers
Part No: 4L560
4L
0.50˝ Top Width
560
56.0˝ Nominal Outside Length
Cut-Edge, Molded Cog Construction Shown
Key Features & Benefits
•Universal classical profile.
•Engineered rubber cushion and insulation.
•Cut-edge, molded cogged construction.
•Heat, ozone, and abrasion resistant.
Q u i e t , S m oo t h - R u n n i n g ,
Exceptionally Energy Efficient
Cogged
for
C oo l e r R u n n i n g
The cogged design of our FHP V-belts (standard on 4L and
5L sizes) provides a greater surface area for heat dissipation and
allows increased air flow around the belt during operation. These
factors help to reduce internal belt temperatures and greatly
improve belt life. Of course, the cogged design also improves
flexibility, an especially important consideration where minimum
or substandard sheave diameters are involved.
Low Vibration
for
Low Noise
Low cross section vibration in rubber-edged, cogged belts reduces
noise generation. This allows you to take advantage of the longer
life and high efficiency of FHP V-belts in noise-sensitive
equipment. But even in typical factory settings, our FHP V-belts
contribute to a quieter operating environment.
Superior Efficiency
for Improved Performance
The historic inefficiency of FHP drives can be traced directly
to the inability of a relatively large envelope belt to transmit a
low-power force efficiently. Transmission loss is especially
significant in factories using large numbers of drives and where
small diameter sheaves are involved. The aggregate loss can be
significant enough to have an adverse effect on equipment
performance.
In addition, the efficiency of our FHP V-belts offers you
the opportunity to achieve full operating power requirements
with a lower horsepower drive, reduced energy requirements,
or both. These considerations can provide highly desirable
economic advantages whether you’re a drive manufacturer or a
drive user.
V - B E L T
These FHP V-belts efficiency begins at 93% when used with
smaller sheaves and increases dramatically as the sheave diameter
increases (Figure 1). Since more of the rated power of the drive is
delivered, actual performance nearly matches design performance.
98
COGGED
96
Efficiency, %
You no longer have to accept the lower energy efficiency
associated with envelope belts on fractional horsepower
lightduty drives. Advanced V-belt technology has resulted
in the development of a cut-edge, molded cog construction
which exceeds conventional envelope belts in every performance
category except oil resistance. This has been confirmed in extensive
testing which proves that our FHP V-belts run smoother and
quieter, last longer, and substantially improve energy efficiency
compared to noncogged belts.
94
NONCOGGED
92
90
88
11⁄2
2
21⁄2
3
31⁄2
4
41⁄2
5
Sheave Diameter, Inches
Figure 1 – Efficiency comparison of cogged vs.
noncogged FHP V-belts (4L section).
75
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S FH P
2l
0.25"
0.16"
3l
0.38"
0.25"
0.22"
0.50"
0.31"
0.25"
0.16"
V - B E L T
0.50"
0.66"
0.38"
0.38"
0.22"
0.66"
0.38"
76
12
14
15
16
Part
Number
Approx.
Outside
Length (in)
4L150
0.38"
4L160
4L170
4L180
4L190
4L200
4L210
4L220
4L230
4L240
4L250
4L260
5l
0.50"
2L120
0.22"
2L140
2L150
2L160
Part
Number
0.50"
0.25"
Approx.
Outside
Length (in)
0.38"
3L120
3L130
3L140
0.38"
3L150
3L160
3L170
3L180
3L190
3L200
3L210
0.22"
3L220
3L230
3L240
3L250
3L260
4l
0.31"
Part
Number
12
0.66"
13
14
15
16
17
18
19
0.38"
20
21
22
23
24
25
26
Approx.
Outside
0.66" (in)
Length
15
16
17
18
19
20
21
22
23
24
25
26
Part
Number
Approx.
Outside
Length (in)
5L230
5L240
5L250
5L260
5L270
5L280
5L290
5L300
5L310
5L320
23
24
25
26
27
28
29
30
31
32
Part
Number
Approx.
Outside
Length (in)
2L180
2L190
2L200
2L220
18
19
20
22
Part
Number
Approx.
Outside
Length (in)
3L270
3L280
3L290
3L300
3L310
3L320
3L330
3L340
3L350
3L360
3L370
3L380
3L390
3L400
3L420
27
28
29
30
31
32
33
34
35
36
37
38
39
40
42
Part
Number
Approx.
Outside
Length (in)
4L270
4L280
4L290
4L300
4L320
4L330
4L340
4L350
4L360
4L370
4L380
4L390
27
28
29
30
32
33
34
35
36
37
38
39
Part
Number
Approx.
Outside
Length (in)
5L330
5L340
5L350
5L360
5L370
5L380
5L390
5L400
5L410
5L420
33
34
35
36
37
38
39
40
41
42
Part
Number
Approx.
Outside
Length (in)
2L240
2L260
2L300
2L310
24
26
30
31
Part
Number
Approx.
Outside
Length (in)
3L430
3L440
3L450
3L460
3L470
3L480
3L490
3L500
3L510
3L520
3L530
3L540
3L550
3L560
3L570
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
Part
Number
Approx.
Outside
Length (in)
4L400
4L410
4L420
4L430
4L440
4L450
4L460
4L470
4L480
4L490
4L500
4L510
40
41
42
43
44
45
46
47
48
49
50
51
Part
Number
Approx.
Outside
Length (in)
5L430
5L440
5L450
5L460
5L470
5L480
5L490
5L500
5L510
5L520
43
44
45
46
47
48
49
50
51
52
Approx.
Part
Outside
Number Length (in)
2L320
32
Approx.
Part
Outside
Number Length (in)
3L580
3L590
3L600
3L610
3L620
3L630
3L640
3L650
3L660
3L670
3L690
3L730
3L740
3L760
58
59
60
61
62
63
64
65
66
67
69
73
74
76
Approx.
Part
Outside
Number Length (in)
4L520
4L530
4L540
4L550
4L560
4L570
4L580
4L590
4L600
52
53
54
55
56
57
58
59
60
Approx.
Part
Outside
Number Length (in)
5L530
5L540
5L550
5L560
5L570
5L580
5L590
5L600
53
54
55
56
57
58
59
60
P O W E R
T R A N S M I S S I O N
V - B E L T
P R O D U C T S 2 0 1 0
M e t a l S h e av e s / P u l l e y s
Part No: 3V3.0-2-JA
3V
Cross Section
3.0
3˝ Pulley Diameter
2
2 Grooves/Teeth
JA
Bushing
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
3V2.2-1-JA
3V2.2-2-JA
3V2.35-1-JA
3V2.35-2-JA
3V2.5-1-JA
3V2.5-2-JA
3V2.5-3-JA
3V2.65-1-JA
3V2.65-2-JA
3V2.65-3-JA
3V2.65-4-JA
3V2.8-1-JA
3V2.8-2-JA
3V2.8-3-JA
3V2.8-4-JA
3V3.0-1-JA
3V3.0-2-JA
3V3.0-3-SH
3V3.0-4-SH
3V3.15-1-JA
3V3.15-2-JA
3V3.15-3-SH
3V3.15-4-SH
3V3.35-1-JA
3V3.35-2-SH
3V3.35-3-SH
3V3.35-4-SH
3V3.65-1-SH
3V3.65-2-SH
3V3.65-3-SH
3V3.65-4-SH
3V4.12-1-SH
3V4.12-2-SH
3V4.12-3-SH
3V4.12-4-SH
3V4.5-1-SH
20180540
20180541
20180542
20180543
20180544
20180545
20180546
20180547
20180548
20180549
20180550
20180551
20180552
20180553
20180554
20180562
20180563
20180564
20180565
20180566
20180567
20180568
20180569
20180570
20180571
20180572
20180573
20180574
20180575
20180576
20180577
20180584
20180585
20180586
20180587
20180588
0.6
0.7
0.8
1.0
0.9
1.1
1.4
0.6
0.8
1.1
1.4
0.7
1.0
1.3
1.6
0.8
1.2
1.6
1.9
0.9
1.4
2.0
2.3
1.1
1.3
1.7
2.2
1.4
1.7
2.3
2.9
1.9
2.2
2.7
3.2
2.3
3V4.5-2-SH
3V4.5-3-SDS
3V4.5-4-SDS
3V4.75-1-SH
3V4.75-2-SH
3V4.75-3-SDS
3V4.75-4-SDS
3V4.75-5-SDS
3V4.75-6-SK
3V4.75-8-SK
3V4.75-10-SK
3V5.0-1-SH
3V5.0-2-SH
3V5.0-3-SDS
3V5.0-4-SDS
3V5.0-5-SDS
3V5.0-6-SK
3V5.0-8-SK
3V5.0-10-SK
3V5.3-1-SH
3V5.3-2-SH
3V5.3-3-SDS
3V5.3-4-SDS
3V5.3-5-SK
3V5.3-6-SK
3V5.3-8-SK
3V5.3-10-SK
3V5.6-1-SH
3V5.6-2-SH
3V5.6-3-SDS
3V5.6-4-SDS
3V5.6-5-SK
3V5.6-6-SK
3V5.6-8-SK
3V5.6-10-SK
3V6.0-1-SH
20180589
20180590
20180591
20180593
20180594
20180595
20180596
20180597
20180598
20180599
20180592
20180601
20180602
20180603
20180604
20180605
20180606
20180607
20180600
20180609
20180610
20180611
20180612
20180613
20180614
20180615
20180608
20180617
20180618
20180619
20180620
20180621
20180622
20180623
20180616
20180625
2.8
3.1
3.5
2.6
3.2
3.6
4.1
4.7
5.2
6.4
7.6
2.9
3.6
4.1
4.6
5.2
6.0
7.3
8.5
3.1
4.1
4.6
5.1
6.2
6.9
8.3
9.6
3.5
4.6
5.2
5.7
7.1
7.8
9.3
10.7
3.5
3V6.0-2-SH
3V6.0-3-SDS
3V6.0-4-SK
3V6.0-5-SK
3V6.0-6-SK
3V6.0-8-SK
3V6.0-10-SK
3V6.5-1-SH
3V6.5-2-SDS
3V6.5-3-SDS
3V6.5-4-SK
3V6.5-5-SK
3V6.5-6-SK
3V6.5-8-SK
3V6.5-10-SK
3V6.9-1-SH
3V6.9-2-SDS
3V6.9-3-SDS
3V6.9-4-SK
3V6.9-5-SK
3V6.9-6-SK
3V6.9-8-SK
3V6.9-10-SK
3V8.0-1-SDS
3V8.0-2-SDS
3V8.0-3-SK
3V8.0-4-SK
3V8.0-5-SK
3V8.0-6-SK
3V8.0-8-SF
3V8.0-10-SF
3V10.6-1-SDS
3V10.6-2-SK
3V10.6-3-SK
3V10.6-4-SK
3V10.6-5-SK
20180626
20180627
20180628
20180629
20180630
20180631
20180624
20180633
20180634
20180635
20180636
20180637
20180638
20180639
20180632
20180641
20180642
20180643
20180644
20180645
20180646
20180647
20180640
20180649
20180650
20180651
20180652
20180653
20180655
20180656
20180648
20180517
20180518
20180519
20180520
20180521
4.5
6.1
7.8
8.5
9.2
10.8
12.4
4.0
4.8
5.8
9.3
10.1
10.9
12.6
14.2
3.3
5.5
6.4
10.9
11.6
12.5
14.3
16.1
4.4
5.4
8.6
10.1
11.6
12.7
19.0
21.2
7.1
11.1
12.7
15.3
16.9
*Weight does not include bushing and is approximate.
V - B E L T
3V N a r r o w ( U l t r a - V ) S h e a v e s
continued on page 78
77
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
3V N a r r o w ( U l t r a - V ) S h e a v e s
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
3V10.6-6-SF
3V10.6-8-SF
3V10.6-10-E
3V14.0-1-SK
3V14.0-2-SK
3V14.0-3-SK
3V14.0-4-SK
3V14.0-5-SF
3V14.0-6-SF
3V14.0-8-E
3V14.0-10-E
20180522
20180523
20180516
20180525
20180526
20180527
20180528
20180529
20180530
20180531
20180524
19.1
22.2
33.2
12.4
15.4
19.1
22.1
26.7
28.9
43.4
47.8
3V19.0-1-SK
3V19.0-2-SK
3V19.0-3-SF
3V19.0-4-SF
3V19.0-5-SF
3V19.0-6-E
3V19.0-8-E
3V19.0-10-E
3V25.0-2-SF
3V25.0-3-SF
3V25.0-4-SF
20180533
20180534
20180535
20180536
20180537
20180538
20180539
20180532
20180556
20180557
20180558
18.6
22.2
33.3
36.3
43.1
49.6
61.6
70.7
37.7
42.0
55.3
3V25.0-5-E
3V25.0-6-E
3V25.0-8-E
3V25.0-10-F
3V33.5-3-SF
3V33.5-4-E
3V33.5-5-E
3V33.5-6-E
3V33.5-8-F
3V33.5-10-F
20180559
20180560
20180561
20180555
20180579
20180580
20180581
20180582
20180583
20180578
Wt.*
66.1
77.7
92.5
115.8
70.8
99.4
105.8
122.0
144.4
178.1
5V N a r r o w ( U l t r a - V ) S h e a v e s
V - B E L T
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
5V4.4-2-SH
5V4.4-3-SDS
5V4.4-4-SD
5V4.4-5-SD
5V4.4-6-SD
5V4.65-2-SDS
5V4.65-3-SDS
5V4.65-4-SD
5V4.65-5-SD
5V4.65-6-SD
5V4.9-2-SDS
5V4.9-3-SDS
5V4.9-4-SD
5V4.9-5-SD
5V4.9-6-SD
5V5.2-2-SDS
5V5.2-3-SDS
5V5.2-4-SD
5V5.2-5-SD
5V5.2-6-SD
5V5.5-2-SDS
5V5.5-3-SDS
5V5.5-4-SD
5V5.5-5-SD
5V5.5-6-SD
5V5.9-2-SDS
5V5.9-3-SDS
5V5.9-4-SD
5V5.9-5-SK
5V5.9-6-SK
5V6.3-2-SK
5V6.3-3-SK
5V6.3-4-SK
20180815
20180816
20180817
20180818
20180819
20180820
20180821
20180822
20180823
20180824
20180825
20180826
20180827
20180828
20180829
20180830
20180831
20180832
20180833
20180834
20180835
20180836
20180837
20180838
20180839
20180840
20180841
20180842
20180843
20180844
20180854
20180855
20180856
3.3
4.2
5.2
6.2
7.1
3.4
4.8
6.0
7.0
8.0
3.8
4.9
6.6
7.6
8.6
4.4
5.6
7.6
8.8
9.9
5.1
6.4
8.7
10.0
11.3
5.8
7.3
10.0
10.6
12.0
7.6
9.2
10.7
5V6.3-5-SK
5V6.3-6-SK
5V6.7-2-SK
5V6.7-3-SK
5V6.7-4-SK
5V6.7-5-SF
5V6.7-6-SF
5V7.1-2-SK
5V7.1-3-SF
5V7.1-4-SF
5V7.1-5-SF
5V7.1-6-SF
5V7.1-7-SF
5V7.1-8-SF
5V7.5-2-SK
5V7.5-3-SF
5V7.5-4-SF
5V7.5-5-SF
5V7.5-6-SF
5V7.5-7-SF
5V7.5-8-SF
5V8.0-2-SK
5V8.0-3-SF
5V8.0-4-E
5V8.0-5-E
5V8.0-6-E
5V8.0-7-E
5V8.0-8-E
5V8.0-9-E
5V8.0-10-E
5V8.5-2-SK
5V8.5-3-SF
5V8.5-4-E
20180857
20180858
20180859
20180860
20180861
20180862
20180863
20180864
20180865
20180866
20180867
20180868
20180869
20180870
20180871
20180872
20180873
20180874
20180875
20180876
20180877
20180879
20180880
20180881
20180882
20180883
20180884
20180885
20180886
20180878
20180888
20180889
20180890
12.3
13.8
9.0
10.7
12.3
13.6
15.2
10.4
11.8
13.6
15.4
17.3
19.1
21.0
12.0
13.6
15.7
17.8
19.9
22.0
24.1
13.9
15.7
18.6
20.9
23.1
25.4
27.7
30.0
32.2
12.2
17.9
21.5
5V8.5-5-E
5V8.5-6-E
5V8.5-7-E
5V8.5-8-E
5V8.5-9-E
5V8.5-10-E
5V9.0-2-SK
5V9.0-3-SF
5V9.0-4-E
5V9.0-5-E
5V9.0-6-E
5V9.0-7-E
5V9.0-8-E
5V9.0-9-E
5V9.0-10-F
5V9.25-2-SK
5V9.25-3-SF
5V9.25-4-E
5V9.25-5-E
5V9.25-6-E
5V9.25-7-E
5V9.25-8-F
5V9.25-9-F
5V9.25-10-F
5V9.75-2-SK
5V9.75-3-SF
5V9.75-4-E
5V9.75-5-E
5V9.75-6-E
5V9.75-7-E
5V9.75-8-F
5V9.75-9-F
5V9.75-10-F
20180891
20180892
20180893
20180894
20180895
20180887
20180897
20180898
20180899
20180900
20180901
20180902
20180903
20180904
20180896
20180906
20180907
20180908
20180909
20180910
20180911
20180912
20180913
20180905
20180915
20180916
20180917
20180918
20180919
20180920
20180921
20180922
20180914
23.9
26.4
28.8
31.2
33.7
36.1
13.4
20.3
24.6
27.2
29.8
32.4
35.0
37.6
44.5
13.7
17.4
25.9
28.5
31.0
33.5
41.3
43.8
46.4
12.6
19.7
29.2
31.9
34.6
37.2
46.6
49.3
52.0
*Weight does not include bushing and is approximate.
78
continued on page 79
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
5V N a r r o w ( U l t r a - V ) S h e a v e s
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
5V10.3-2-SK
5V10.3-3-SF
5V10.3-4-E
5V10.3-5-E
5V10.3-6-E
5V10.3-7-F
5V10.3-8-F
5V10.3-9-F
5V10.3-10-F
5V10.9-2-SK
5V10.9-3-SF
5V10.9-4-E
5V10.9-5-E
5V10.9-6-E
5V10.9-7-F
5V10.9-8-F
5V10.9-9-F
5V10.9-10-F
5V11.3-2-SK
5V11.3-3-SF
5V11.3-4-E
5V11.3-5-E
5V11.3-6-E
5V11.3-7-F
5V11.3-8-F
5V11.3-9-F
5V11.3-10-F
5V11.8-2-SK
5V11.8-3-SF
5V11.8-4-E
5V11.8-5-E
5V11.8-6-E
5V11.8-7-F
5V11.8-8-F
5V11.8-9-F
5V11.8-10-F
5V12.5-2-SF
5V12.5-3-E
5V12.5-4-E
5V12.5-5-E
5V12.5-6-F
5V12.5-7-F
5V12.5-8-F
5V12.5-9-F
5V12.5-10-J
5V13.2-2-SF
5V13.2-3-E
20180658
20180659
20180660
20180661
20180662
20180664
20180665
20180666
20180657
20180668
20180669
20180670
20180671
20180672
20180674
20180675
20180676
20180667
20180679
20180680
20180681
20180682
20180683
20180685
20180686
20180687
20180677
20180690
20180691
20180692
20180693
20180694
20180696
20180697
20180699
20180688
20180702
20180703
20180704
20180705
20180706
20180708
20180709
20180710
20180700
20180713
20180714
13.7
20.7
27.1
30.4
33.7
50.1
53.0
55.9
58.9
14.5
19.4
29.1
32.7
36.2
56.7
59.8
62.9
65.9
16.3
21.2
33.1
36.7
40.9
62.9
66.5
70.1
73.6
17.1
23.7
34.9
38.5
43.5
53.9
57.5
61.1
64.6
18.9
28.3
33.7
37.5
54.7
58.7
62.4
66.4
77.0
20.1
30.2
5V13.2-4-E
5V13.2-5-E
5V13.2-6-F
5V13.2-7-F
5V13.2-8-F
5V13.2-9-F
5V13.2-10-J
5V14.0-2-SF
5V14.0-3-E
5V14.0-4-E
5V14.0-5-E
5V14.0-6-F
5V14.0-7-F
5V14.0-8-F
5V14.0-9-F
5V14.0-10-J
5V15.0-2-SF
5V15.0-3-E
5V15.0-4-E
5V15.0-5-E
5V15.0-6-F
5V15.0-7-F
5V15.0-8-F
5V15.0-9-J
5V15.0-10-J
5V16.0-2-SF
5V16.0-3-E
5V16.0-4-E
5V16.0-5-E
5V16.0-6-F
5V16.0-7-F
5V16.0-8-F
5V16.0-9-J
5V16.0-10-J
5V18.7-2-SF
5V18.7-3-E
5V18.7-4-E
5V18.7-5-F
5V18.7-6-F
5V18.7-7-F
5V18.7-8-J
5V18.7-9-J
5V18.7-10-J
5V21.2-2-SF
5V21.2-3-E
5V21.2-4-E
5V21.2-5-F
20180715 35.8
20180716 39.9
20180717 59.2
20180719 63.5
20180720 67.5
20180722 73.6
20180711 83.0
20180724 22.9
20180725 31.6
20180726 37.9
20180727 42.3
20180728 64.2
20180730 68.7
20180731 72.9
20180732 79.8
20180723 89.4
20180735 24.8
20180736 35.7
20180737 40.8
20180738 47.0
20180739 61.7
20180741 66.6
20180742 71.1
20180744 93.6
20180733 93.2
20180747 27.1
20180748 38.2
20180749 44.1
20180750 50.5
20180751 66.0
20180753 72.2
20180754 77.0
20180755 93.1
20180745 98.1
20180757 36.3
20180758 47.5
20180759 57.3
20180760 76.5
20180761 83.0
20180763 89.3
20180764 106.3
20180765 112.7
20180756 120.4
20180767 42.1
20180768 54.2
20180769 66.5
20180770 87.0
Part No.
SAP No.
5V21.2-6-F
5V21.2-7-J
5V21.2-8-J
5V21.2-9-J
5V21.2-10-J
5V23.6-2-E
5V23.6-3-E
5V23.6-4-F
5V23.6-5-F
5V23.6-6-J
5V23.6-7-J
5V23.6-8-J
5V23.6-9-J
5V23.6-10-M
5V28.0-2-E
5V28.0-3-E
5V28.0-4-F
5V28.0-5-F
5V28.0-6-J
5V28.0-7-J
5V28.0-8-J
5V28.0-9-M
5V28.0-10-M
5V31.5-3-F
5V31.5-4-F
5V31.5-5-J
5V31.5-6-J
5V31.5-7-J
5V31.5-8-M
5V31.5-9-M
5V31.5-10-M
5V37.5-3-F
5V37.5-4-F
5V37.5-5-J
5V37.5-6-J
5V37.5-7-M
5V37.5-8-M
5V37.5-9-M
5V37.5-10-M
5V50.0-3-F
5V50.0-4-J
5V50.0-5-J
5V50.0-6-M
5V50.0-7-M
5V50.0-8-M
5V50.0-9-M
5V50.0-10-M
20180771
20180773
20180774
20180775
20180766
20180778
20180779
20180780
20180781
20180782
20180784
20180785
20180786
20180776
20180788
20180789
20180790
20180791
20180792
20180794
20180795
20180796
20180787
20180798
20180799
20180800
20180801
20180803
20180804
20180805
20180797
20180807
20180808
20180809
20180810
20180812
20180813
20180814
20180806
20180846
20180847
20180848
20180849
20180851
20180852
20180853
20180845
Wt.*
96.2
115.3
122.9
130.0
143.5
54.8
69.1
87.9
101.6
117.5
125.8
138.7
149.2
211.1
71.1
94.4
115.2
132.7
153.1
165.1
175.1
239.1
249.3
118.1
131.3
158.7
182.1
196.2
261.1
277.1
294.5
151.5
181.9
221.6
237.8
315.0
331.6
363.9
386.4
222.5
240.8
296.8
367.5
422.1
472.7
494.6
548.3
V - B E L T
Part No.
*Weight does not include bushing and is approximate.
79
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
8V N a r r o w ( U l t r a - V ) S h e a v e s
V - B E L T
Part No.
SAP No.
8V12.5-4-F
8V12.5-5-F
8V12.5-6-F
8V12.5-8-J
8V12.5-10-J
8V12.5-12-M
8V13.2-4-F
8V13.2-5-F
8V13.2-6-F
8V13.2-8-J
8V13.2-10-J
8V13.2-12-M
8V14.0-4-F
8V14.0-5-F
8V14.0-6-F
8V14.0-8-J
8V14.0-10-J
8V14.0-12-M
8V15.0-4-F
8V15.0-5-F
8V15.0-6-J
8V15.0-8-J
8V15.0-10-M
8V15.0-12-M
8V16.0-4-F
8V16.0-5-F
8V16.0-6-J
8V16.0-8-J
8V16.0-10-M
8V16.0-12-M
8V17.0-4-F
8V17.0-5-J
8V17.0-6-J
8V17.0-8-M
8V17.0-10-M
8V17.0-12-M
8V18.0-4-F
20180925
20180926
20180927
20180928
20180923
20180924
20180931
20180932
20180933
20180934
20180929
20180930
20180937
20180938
20180939
20180940
20180935
20180936
20180943
20180944
20180945
20180946
20180941
20180942
20180949
20180950
20180951
20180952
20180947
20180948
20180955
20180956
20180957
20180958
20180953
20180954
20180961
Wt.*
75.0
82.8
90.6
113.0
132.8
163.1
68.0
77.7
86.1
109.1
132.5
185.2
74.0
84.7
93.6
118.1
144.9
210.9
82.2
94.3
111.1
130.4
224.5
245.5
88.4
101.7
121.5
142.7
262.0
285.1
99.0
117.3
131.8
202.1
234.4
286.6
107.7
Part No.
SAP No.
Wt.*
8V18.0-5-J
8V18.0-6-J
8V18.0-8-M
8V18.0-10-M
8V18.0-12-M
8V19.0-4-F
8V19.0-5-J
8V19.0-6-J
8V19.0-8-M
8V19.0-10-M
8V19.0-12-N
8V20.0-4-J
8V20.0-5-J
8V20.0-6-M
8V20.0-8-M
8V20.0-10-M
8V20.0-12-N
8V21.2-4-J
8V21.2-5-J
8V21.2-6-M
8V21.2-8-M
8V21.2-10-M
8V21.2-12-N
8V22.4-4-J
8V22.4-5-M
8V22.4-6-M
8V22.4-8-M
8V22.4-10-N
8V22.4-12-N
8V24.8-4-M
8V24.8-5-M
8V24.8-6-M
8V24.8-8-N
8V24.8-10-N
8V24.8-12-N
8V30.0-4-M
8V30.0-5-M
20180962
20180963
20180964
20180959
20180960
20180967
20180968
20180969
20180970
20180965
20180966
20180973
20180974
20180975
20180976
20180971
20180972
20180979
20180980
20180981
20180982
20180977
20180978
20180985
20180986
20180987
20180988
20180983
20180984
20180991
20180992
20180993
20180994
20180989
20180990
20180997
20180998
131.5
143.6
213.4
248.1
303.2
116.7
142.2
155.1
228.7
266.1
329.2
112.3
151.5
208.1
250.6
283.9
350.4
126.8
167.8
228.6
269.8
306.0
369.3
138.2
241.6
246.2
303.7
359.3
406.5
212.8
231.9
250.9
365.7
411.3
464.8
252.0
293.0
Part No.
SAP No.
8V30.0-6-M
8V30.0-8-N
8V30.0-10-N
8V30.0-12-P
8V35.5-4-M
8V35.5-5-M
8V35.5-6-N
8V35.5-8-N
8V35.5-10-P
8V35.5-12-P
8V40.0-4-M
8V40.0-5-M
8V40.0-6-N
8V40.0-8-N
8V40.0-10-P
8V40.0-12-P
8V44.5-4-M
8V44.5-5-N
8V44.5-6-N
8V44.5-8-P
8V44.5-10-P
8V44.5-12-P
8V53.0-4-M
8V53.0-5-N
8V53.0-6-N
8V53.0-8-P
8V53.0-10-P
8V53.0-12-W
8V63.0-6-P
8V63.0-8-P
8V63.0-10-W
8V63.0-12-W
8V71.0-6-P
8V71.0-8-W
8V71.0-10-W
8V71.0-12-W
20180999
20181000
20180995
20180996
20181003
20181004
20181005
20181006
20181001
20181002
20181009
20181010
20181011
20181012
20181007
20181008
20181015
20181016
20181017
20181018
20181013
20181014
20181021
20181022
20181023
20181024
20181019
20181020
20181027
20181028
20181025
20181026
20181031
20181032
20181029
20181030
Wt.*
319.8
410.9
505.8
584.5
294.6
356.9
415.8
523.9
618.4
711.2
373.0
406.3
498.1
599.7
730.3
821.9
400.2
486.2
521.6
696.2
766.9
895.4
509.6
624.8
705.7
886.0
1024.0
1305.2
890.4
1116.9
1412.0
1540.5
1045.8
1478.6
1617.3
1757.8
*Weight does not include bushing and is approximate.
“ A ” C l a s s ic a l
( C o n v e n ti o n a l ) S h e a v e s
Part No.
SAP No.
Wt.*
3.4-2A-SH
20179193
1.9
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
4.6-2A-SDS
20179273
3.0
18.0-2A-SK
20179098
19.8
*Weight does not include bushing and is approximate.
80
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
Part No.
3.4-1B-SH
3.4-2B-SH
3.4-3B-SH
3.4-4B-SD
3.4-5B-SD
3.4-6B-SD
3.6-1B-SH
3.6-2B-SH
3.6-3B-SH
3.6-4B-SD
3.6-5B-SD
3.6-6B-SD
3.8-1B-SH
3.8-2B-SH
3.8-3B-SH
3.8-4B-SD
3.8-5B-SD
3.8-6B-SD
4.0-1B-SH
4.0-2B-SH
4.0-3B-SH
4.0-4B-SD
4.0-5B-SD
4.0-6B-SD
4.2-1B-SH
4.2-2B-SH
4.2-3B-SH
4.2-4B-SD
4.2-5B-SD
4.2-6B-SD
4.4-1B-SH
4.4-2B-SH
4.4-3B-SH
4.4-4B-SD
4.4-5B-SD
4.4-6B-SD
4.6-1B-SDS
4.6-2B-SDS
4.6-3B-SD
4.6-4B-SD
4.6-5B-SD
4.6-6B-SD
4.8-1B-SDS
4.8-2B-SDS
4.8-3B-SD
4.8-4B-SD
4.8-5B-SD
4.8-6B-SD
5.0-1B-SDS
SAP No.
20179192
20179194
20179195
20179196
20179197
20179198
20179199
20179200
20179201
20179202
20179203
20179204
20179205
20179206
20179207
20179208
20179209
20179210
20179254
20179255
20179256
20179257
20179258
20179259
20179260
20179261
20179262
20179263
20179264
20179265
20179266
20179267
20179268
20179269
20179270
20179271
20179272
20179274
20179275
20179276
20179277
20179278
20179279
20179280
20179281
20179282
20179283
20179284
20179306
Wt.*
1.2
2.2
3.0
4.0
4.8
5.6
1.4
2.5
3.4
4.6
5.5
6.4
1.6
2.9
3.8
5.1
6.1
7.0
2.1
3.1
4.1
5.4
6.4
7.4
2.3
3.8
4.5
5.8
6.8
7.9
2.5
3.8
4.9
6.3
7.3
8.4
2.5
3.8
5.7
6.9
8.0
9.1
2.8
4.2
6.4
7.7
9.0
9.9
3.1
Part No.
5.0-2B-SDS
5.0-3B-SD
5.0-4B-SD
5.0-5B-SD
5.0-6B-SD
5.2-1B-SDS
5.2-2B-SDS
5.2-3B-SD
5.2-4B-SD
5.2-5B-SD
5.2-6B-SD
5.4-1B-SDS
5.4-2B-SDS
5.4-3B-SD
5.4-4B-SD
5.4-5B-SK
5.4-6B-SK
5.4-7B-SK
5.4-8B-SK
5.4-10B-SK
5.6-1B-SDS
5.6-2B-SDS*
5.6-3B-SD*
5.6-4B-SD
5.6-5B-SK
5.6-6B-SK
5.6-7B-SK
5.6-8B-SK
5.6-10B-SK
5.8-1B-SDS
5.8-2B-SDS
5.8-3B-SD
5.8-4B-SD
5.8-5B-SK
5.8-6B-SK
5.8-7B-SK
5.8-8B-SK
5.8-10B-SK
6.0-1B-SDS
6.0-2B-SDS*
6.0-3B-SD*
6.0-4B-SD
6.0-5B-SK
6.0-6B-SK
6.0-7B-SF
6.0-8B-SF
6.0-10B-SF
6.2-1B-SDS
6.2-2B-SDS
SAP No.
20179307
20179308
20179310
20179312
20179313
20179314
20179316
20179317
20179318
20179319
20179320
20179322
20179323
20179324
20179325
20179326
20179327
20179328
20179329
20179321
20179331
20179332
20179334
20179336
20179338
20179339
20179340
20179341
20179330
20179343
20179344
20179345
20179346
20179347
20179348
20179349
20179350
20179342
20179366
20179367
20179368
20179370
20179372
20179374
20179376
20179377
20179365
20179379
20179380
Wt.*
Part No.
SAP No.
Wt.*
4.6
7.0
8.0
9.7
10.7
3.3
5.2
7.7
9.1
10.5
11.9
3.6
5.5
8.2
9.4
10.0
11.3
12.7
14.0
16.7
3.8
5.8
8.9
10.2
10.9
12.6
14.1
15.6
18.6
3.9
6.4
9.6
11.0
11.7
13.5
15.1
16.7
19.8
4.2
6.6
10.1
11.7
12.5
14.5
15.2
16.7
19.9
4.3
6.9
6.2-3B-SD
6.2-4B-SD
6.2-5B-SK
6.2-6B-SK
6.2-7B-SF
6.2-8B-SF
6.2-10B-SF
6.4-1B-SDS
6.4-2B-SDS
6.4-3B-SD
6.4-4B-SD
6.4-5B-SK
6.4-6B-SK
6.4-7B-SF
6.4-8B-SF
6.4-10B-SF
6.6-1B-SDS
6.6-2B-SDS
6.6-3B-SD
6.6-4B-SD
6.6-5B-SK
6.6-6B-SK
6.6-7B-SF
6.6-8B-SF
6.6-10B-SF
6.8-1B-SDS
6.8-2B-SDS*
6.8-3B-SD*
6.8-4B-SD
6.8-5B-SK
6.8-6B-SK
6.8-7B-SF
6.8-8B-SF
6.8-10B-SF
7.0-1B-SDS
7.0-2B-SK*
7.0-3B-SK*
7.0-4B-SK
7.0-5B-SF
7.0-6B-SF
7.0-7B-SF
7.0-8B-SF
7.0-10B-SF
7.4-1B-SDS
7.4-2B-SK
7.4-3B-SK
7.4-4B-SK
7.4-5B-SF
7.4-6B-SF
20179381
20179382
20179383
20179384
20179385
20179386
20179378
20179388
20179389
20179390
20179391
20179392
20179393
20179394
20179395
20179387
20179397
20179398
20179399
20179400
20179401
20179402
20179403
20179404
20179396
20179406
20179407
20179408
20179409
20179410
20179411
20179412
20179413
20179405
20179415
20179417
20179419
20179421
20179423
20179425
20179427
20179429
20179414
20179432
20179433
20179434
20179435
20179436
20179437
10.7
11.8
13.7
15.4
16.7
18.5
22.0
4.6
7.1
9.4
12.3
14.3
16.0
17.3
19.0
22.5
5.4
7.2
9.4
11.0
15.0
16.7
18.4
20.2
23.8
5.6
7.7
10.4
12.3
16.2
18.1
19.5
21.4
25.2
6.1
11.3
13.2
15.2
16.7
18.7
20.7
22.7
26.6
6.5
11.7
14.9
14.2
18.5
20.6
V - B E L T
“ A / B ” C l a s s ic a l
( C o n v e n ti o n a l ) S h e a v e s
continued on page 82
*Weight does not include bushing and is approximate.
81
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
“ A / B ” C l a s s ic a l
( C o n v e n ti o n a l ) S h e a v e s
Part No.
V - B E L T
7.4-7B-SF
7.4-8B-SF
7.4-10B-SF
8.0-1B-SDS
8.0-2B-SK*
8.0-3B-SK*
8.0-4B-SK
8.0-5B-SF
8.0-6B-SF
8.6-1B-SDS
8.6-2B-SK*
8.6-3B-SK*
8.6-4B-SK
8.6-5B-SF
8.6-6B-SF
8.6-7B-E
8.6-8B-E
8.6-10B-E
9.4-1B-SDS
9.4-2B-SK*
9.4-3B-SK*
9.4-4B-SK
9.4-5B-SF
9.4-6B-SF
9.4-7B-E
9.4-8B-E
9.4-10B-E
11.0-1B-SDS
11.0-2B-SK*
11.0-3B-SK*
11.0-4B-SK
11.0-5B-SF
11.0-6B-SF
11.0-7B-E
11.0-8B-E
11.0-10B-E
12.4-1B-SDS
12.4-2B-SK
12.4-3B-SK
SAP No.
20179438
20179439
20179431
20179447
20179449
20179451
20179453
20179455
20179457
20179473
20179474
20179475
20179476
20179477
20179478
20179479
20179480
20179472
20179498
20179499
20179500
20179501
20179502
20179503
20179504
20179505
20179497
20178934
20178936
20178938
20178940
20178942
20178944
20178946
20178948
20178931
20178970
20178971
20178972
Wt.*
22.7
24.8
28.9
7.4
11.5
13.8
16.2
19.3
24.1
8.3
12.5
14.8
14.6
17.8
27.3
31.5
34.0
38.9
7.4
12.5
15.1
21.1
20.6
27.1
32.7
34.2
39.9
10.7
14.2
17.6
24.4
25.0
29.7
42.0
45.3
51.9
11.2
17.0
20.5
Part No.
12.4-4B-SK
12.4-5B-SF
12.4-6B-SF
12.4-7B-E
12.4-8B-E
12.4-10B-E
13.6-1B-SDS
13.6-2B-SK
13.6-3B-SK
13.6-4B-SK
13.6-5B-SF
13.6-6B-SF
13.6-7B-E
13.6-8B-E
13.6-10B-F
15.4-1B-SK
15.4-2B-SK*
15.4-3B-SK*
15.4-4B-SF
15.4-5B-SF
15.4-6B-SF
15.4-7B-E
15.4-8B-E
15.4-10B-F
16.0-1B-SK
16.0-2B-SK
16.0-3B-SK
16.0-4B-SF
16.0-5B-SF
16.0-6B-SF
16.0-7B-E
16.0-8B-E
16.0-10B-F
18.4-1B-SK
18.4-2B-SK
18.4-3B-SK
18.4-4B-SF
18.4-5B-SF
18.4-6B-SF
*Weight does not include bushing and is approximate.
82
SAP No.
20178973
20178974
20178975
20178976
20178977
20178969
20179004
20179005
20179006
20179007
20179008
20179009
20179010
20179011
20179003
20179045
20179046
20179047
20179048
20179049
20179050
20179051
20179052
20179044
20179065
20179067
20179069
20179072
20179075
20179078
20179081
20179083
20179060
20179113
20179114
20179115
20179116
20179117
20179118
Wt.*
Part No.
SAP No.
25.7
29.5
34.5
49.4
52.7
59.9
13.0
18.2
21.4
27.1
32.2
37.4
48.9
52.9
73.2
16.7
21.6
26.3
33.0
39.3
43.1
60.5
63.9
85.7
16.4
21.9
29.1
35.8
44.1
48.8
63.7
67.0
89.4
19.4
27.6
33.6
42.0
51.8
57.7
18.4-7B-F
18.4-8B-F
18.4-10B-F
20.0-1B-SK
20.0-2B-SF
20.0-3B-SF
20.0-4B-SF
20.0-5B-E
20.0-6B-E
20.0-7B-F
20.0-8B-F
20.0-10B-F
25.0-1B-SF
25.0-2B-SF
25.0-3B-SF
25.0-4B-E
25.0-5B-E
25.0-6B-E
25.0-7B-F
25.0-8B-F
25.0-10B-F
30.0-1B-SF
30.0-2B-SF
30.0-3B-SF
30.0-4B-E
30.0-5B-E
30.0-6B-E
30.0-7B-F
30.0-8B-F
30.0-10B-F
38.0-2B-SF
38.0-3B-E
38.0-4B-E
38.0-5B-E
38.0-6B-E
38.0-7B-F
38.0-8B-F
38.0-10B-J
20179119
20179120
20179112
20179126
20179128
20179130
20179132
20179135
20179138
20179141
20179143
20179121
20179169
20179170
20179171
20179172
20179173
20179174
20179175
20179176
20179168
20179214
20179215
20179217
20179219
20179221
20179223
20179225
20179227
20179211
20179247
20179248
20179249
20179250
20179251
20179252
20179253
20179246
Wt.*
77.1
86.5
98.1
28.9
33.2
38.6
49.1
62.0
71.4
92.3
98.8
111.9
40.0
50.3
62.8
76.3
90.3
109.9
123.2
135.5
115.1
52.0
71.2
87.4
103.2
117.3
129.8
151.8
162.3
193.4
94.9
136.4
151.1
165.8
183.0
233.0
236.5
290.2
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
“ A / B ” C l a s s ic a l
( C o n v e n ti o n a l ) S h e a v e s
(Large Bore)
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
5.6-2LB-SF
5.6-3LB-SF
6.0-2LB-SF
6.0-3LB-SF
6.8-2LB-SF
6.8-3LB-SF
20332969
20333000
20333001
20333002
20333003
20333004
6.1
7.6
7.3
8.7
10.0
11.8
7.0-2LB-SF
7.0-3LB-SF
8.0-2LB-SF
8.0-3LB-SF
8.6-2LB-SF
8.6-3LB-SF
20333005
20333006
20333007
20333008
20333009
20333010
10.8
12.7
14.8
17.1
13.0
15.3
9.4-2LB-SF
9.4-3LB-SF
11.0-2LB-SF
11.0-3LB-SF
15.4-2LB-SF
15.4-3LB-SF
20333011
20333012
20333013
20333014
20333015
20333016
14.7
17.7
16.1
19.9
23.4
29.1
“ C ” C l a s s ic a l
( C o n v e n ti o n a l ) S h e a v e s
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
20179309
20179311
20179333
20179335
20179337
20179369
20179371
20179373
20179375
20179416
20179418
20179420
20179422
20179424
20179426
20179428
20179430
20179440
20179441
20179442
20179443
20179444
20179445
20179448
20179450
20179452
20179454
20179456
20179458
20179459
20179460
20179461
20179446
20179463
8.6
10.2
8.8
11.1
12.8
9.4
10.9
12.5
14.0
9.7
12.4
15.2
18.0
20.8
23.6
26.4
29.2
11.4
14.4
17.5
20.5
23.6
26.6
13.0
16.3
20.7
24.0
27.3
30.6
34.0
37.3
40.6
43.9
12.6
8.5-2C-SF
8.5-3C-E
8.5-4C-E
8.5-5C-E
8.5-6C-E
8.5-7C-E
8.5-8C-E
8.5-9C-E
8.5-10C-E
9.0-1C-SF
9.0-2C-SF
9.0-3C-E
9.0-4C-E
9.0-5C-E
9.0-6C-F
9.0-7C-F
9.0-8C-F
9.0-9C-J
9.0-10C-J
9.0-12C-J
9.5-1C-SF
9.5-2C-SF
9.5-3C-E
9.5-4C-E
9.5-5C-E
9.5-6C-F
9.5-7C-F
9.5-8C-F
9.5-9C-J
9.5-10C-J
9.5-12C-J
10.0-1C-SF
10.0-2C-SF
10.0-3C-E
20179464
20179465
20179466
20179467
20179468
20179469
20179470
20179471
20179462
20179484
20179487
20179489
20179491
20179492
20179493
20179494
20179495
20179496
20179481
20179482
20179508
20179509
20179510
20179511
20179512
20179513
20179514
20179515
20179516
20179506
20179507
20178911
20178912
20178913
16.6
23.7
27.3
30.8
34.4
37.9
41.5
45.0
48.6
13.7
18.2
26.9
30.7
34.5
43.0
46.7
50.5
54.0
59.6
64.8
15.1
20.1
30.6
34.9
39.1
49.1
53.3
57.6
63.6
67.8
76.2
16.1
21.4
33.8
10.0-4C-E
10.0-5C-E
10.0-6C-F
10.0-7C-F
10.0-8C-F
10.0-9C-J
10.0-10C-J
10.0-12C-J
10.5-1C-SF
10.5-2C-SF
10.5-3C-E
10.5-4C-E
10.5-5C-E
10.5-6C-F
10.5-7C-F
10.5-8C-F
10.5-9C-J
10.5-10C-J
10.5-12C-J
11.0-1C-SF
11.0-2C-SF
11.0-3C-E
11.0-4C-E
11.0-5C-E
11.0-6C-F
11.0-7C-F
11.0-8C-F
11.0-9C-J
11.0-10C-J
11.0-12C-J
12.0-1C-SF
12.0-2C-SF
12.0-3C-E
12.0-4C-E
20178914 38.1
20178915 42.4
20178916 54.0
20178917 58.3
20178918 62.6
20178919 69.9
20178109 74.1
20178910 82.6
20178922 17.4
20178923 23.2
20178924 31.4
20178925 35.9
20178926 40.4
20178927 60.0
20178928 64.5
20178929 69.0
20178930 77.7
20178920 82.2
20178921 91.2
20178935 15.4
20178937 19.5
20178939 33.6
20178941 38.4
20178943 43.1
20178945 66.2
20178947 70.9
20178949 75.6
20178950 85.9
20178932 90.6
20178933 100.1
20178955 16.9
20178956 21.7
20178957 38.4
20178959 43.6
Wt.*
V - B E L T
Part No.
5.0-3C-SD
5.0-4C-SD
5.6-2C-SD
5.6-3C-SD
5.6-4C-SD
6.0-3C-SF
6.0-4C-SF
6.0-5C-SF
6.0-6C-SF
7.0-1C-SF
7.0-2C-SF
7.0-3C-SF
7.0-4C-SF
7.0-5C-SF
7.0-6C-SF
7.0-7C-SF
7.0-8C-SF
7.5-1C-SF
7.5-2C-SF
7.5-3C-SF
7.5-4C-SF
7.5-5C-SF
7.5-6C-SF
8.0-1C-SF
8.0-2C-SF
8.0-3C-E
8.0-4C-E
8.0-5C-E
8.0-6C-E
8.0-7C-E
8.0-8C-E
8.0-9C-E
8.0-10C-E
8.5-1C-SF
continued on page 84
*Weight does not include bushing and is approximate.
83
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
“ C ” C l a s s ic a l
( C o n v e n ti o n a l ) S h e a v e s
Part No.
V - B E L T
12.0-5C-E
12.0-6C-F
12.0-7C-F
12.0-8C-F
12.0-9C-J
12.0-10C-J
12.0-12C-J
13.0-1C-SF
13.0-2C-SF
13.0-3C-E
13.0-4C-E
13.0-5C-E
13.0-6C-F
13.0-7C-F
13.0-8C-F
13.0-9C-J
13.0-10C-J
13.0-12C-J
14.0-1C-SF
14.0-2C-SF
14.0-3C-E
14.0-4C-E
14.0-5C-E
14.0-6C-F
14.0-7C-F
14.0-8C-F
14.0-9C-J
14.0-10C-J
14.0-12C-J
16.0-1C-SF
16.0-2C-SF
16.0-3C-E
16.0-4C-E
16.0-5C-E
16.0-6C-F
16.0-7C-F
16.0-8C-F
16.0-9C-J
16.0-10C-J
16.0-12C-J
SAP No.
20178961
20178963
20178965
20178966
20178968
20178951
20178953
20178982
20178983
20178984
20178986
20178988
20178990
20178992
20178993
20178995
20178978
20178980
20179016
20179017
20179018
20179020
20179022
20179024
20179026
20179027
20179029
20179012
20179014
20179066
20179068
20179070
20179073
20179076
20179079
20179082
20179084
20179086
20179061
20179063
Wt.*
48.8
62.5
67.7
72.9
103.1
108.4
118.8
18.5
23.9
42.4
49.4
55.1
70.0
75.6
81.3
95.9
101.6
116.4
20.3
25.9
41.7
50.7
57.2
73.0
81.8
88.0
104.5
110.8
127.3
23.5
32.2
49.8
60.2
71.2
87.7
100.7
108.6
130.2
141.3
160.3
*Weight does not include bushing and is approximate.
84
Part No.
18.0-1C-SF
18.0-2C-SF
18.0-3C-E
18.0-4C-E
18.0-5C-E
18.0-6C-F
18.0-7C-F
18.0-8C-F
18.0-9C-J
18.0-10C-J
18.0-12C-J
20.0-1C-SF
20.0-2C-SF
20.0-3C-E
20.0-4C-E
20.0-5C-F
20.0-6C-F
20.0-7C-J
20.0-8C-J
20.0-9C-J
20.0-10C-J
20.0-12C-M
24.0-1C-SF
24.0-2C-SF
24.0-3C-E
24.0-4C-F
24.0-5C-F
24.0-6C-F
24.0-7C-J
24.0-8C-J
24.0-9C-J
24.0-10C-M
24.0-12C-M
27.0-2C-F
27.0-3C-F
27.0-4C-F
27.0-5C-F
27.0-6C-J
27.0-7C-J
SAP No.
20179097
20179099
20179100
20179102
20179104
20179106
20179108
20179109
20179111
20179093
20179095
20179127
20179129
20179131
20179133
20179136
20179139
20179142
20179144
20179146
20179122
20179124
20333017
20179156
20179157
20179159
20179161
20179163
20179165
20179166
20179167
20179154
20179155
20179179
20179180
20179182
20179184
20179186
20179188
Wt.*
27.8
42.2
58.6
68.6
79.1
98.3
113.9
123.3
139.3
148.7
172.0
31.8
42.1
62.6
76.9
96.5
109.8
139.3
146.5
159.2
169.7
257.4
41.2
57.6
78.7
100.4
106.7
122.1
168.5
173.4
191.7
263.1
286.2
79.4
103.0
116.8
129.2
158.8
195.8
Part No.
SAP No.
27.0-8C-J
27.0-9C-J
30.0-2C-F
30.0-3C-F
30.0-4C-F
30.0-5C-F
30.0-6C-J
30.0-7C-J
30.0-8C-J
30.0-9C-M
30.0-10C-M
30.0-12C-M
36.0-3C-F
36.0-4C-F
36.0-5C-J
36.0-6C-J
36.0-7C-J
36.0-8C-M
36.0-9C-M
36.0-10C-M
36.0-12C-M
44.0-3C-F
44.0-4C-J
44.0-5C-J
44.0-6C-J
44.0-7C-M
44.0-8C-M
44.0-9C-M
44.0-10C-M
44.0-12C-M
50.0-3C-F
50.0-4C-J
50.0-5C-J
50.0-6C-M
50.0-7C-M
50.0-8C-M
50.0-9C-M
50.0-10C-M
50.0-12C-M
20179189
20179191
20179216
20179218
20179220
20179222
20179224
20179226
20179228
20179229
20179212
20179213
20179239
20179240
20179241
20179242
20179243
20179244
20179245
20179237
20179238
20179294
20179295
20179296
20179297
20179298
20179299
20179300
20179292
20179293
20179353
20179354
20179355
20179356
20179357
20179358
20179359
20179351
20179352
Wt.*
226.3
226.8
82.4
115.4
136.1
160.8
192.7
220.8
240.0
316.8
332.1
362.7
161.7
194.2
220.3
254.5
273.1
355.3
379.0
397.5
434.5
242.8
270.4
293.2
315.9
429.2
452.0
474.6
531.8
577.3
304.1
337.4
365.8
484.4
512.8
541.1
569.5
662.9
719.6
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
“ D ” C l a s s ic a l
( C o n v e n ti o n a l ) S h e a v e s
12.0-3D-F
12.0-4D-F
12.0-5D-F
12.0-6D-J
12.0-8D-J
12.0-10D-M
12.0-12D-M
13.0-3D-F
13.0-4D-F
13.0-5D-F
13.0-6D-J
13.0-8D-J
13.0-10D-M
13.0-12D-M
13.5-3D-F
13.5-4D-F
13.5-5D-F
13.5-6D-J
13.5-8D-J
13.5-10D-M
13.5-12D-M
14.0-3D-F
14.0-4D-F
14.0-5D-F
14.0-6D-J
14.0-8D-J
14.0-10D-M
14.0-12D-M
14.5-3D-F
14.5-4D-F
14.5-5D-F
14.5-6D-J
14.5-8D-J
14.5-10D-M
14.5-12D-M
15.0-3D-F
15.0-4D-F
15.0-5D-F
15.0-6D-J
SAP No.
20178958
20178960
20178962
20178964
20178967
20178952
20178954
20178985
20178987
20178989
20178991
20178994
20178979
20178981
20178998
20178999
20179000
20179001
20179002
20178996
20178997
20179019
20179021
20179023
20179025
20179028
20179013
20179015
20179032
20179033
20179034
20179035
20179036
20179030
20179031
20179039
20179040
20179041
20179042
Wt.*
59.2
69.0
79.4
105.9
124.5
157.5
176.1
63.0
74.8
85.1
104.3
124.2
189.2
209.7
66.2
78.7
89.4
109.8
130.4
205.4
226.8
69.4
82.7
93.9
115.4
136.7
222.1
244.4
72.8
86.8
100.8
121.1
143.1
239.4
262.5
78.9
91.0
105.7
126.9
Part No.
15.0-8D-J
15.0-10D-M
15.0-12D-M
15.5-3D-F
15.5-4D-F
15.5-5D-F
15.5-6D-J
15.5-8D-J
15.5-10D-M
15.5-12D-M
16.0-3D-F
16.0-4D-F
16.0-5D-F
16.0-6D-J
16.0-8D-J
16.0-10D-M
16.0-12D-M
17.0-4D-J
17.0-5D-J
17.0-6D-J
17.0-8D-J
17.0-10D-M
17.0-12D-M
18.0-3D-J
18.0-4D-J
18.0-5D-J
18.0-6D-J
18.0-8D-M
18.0-10D-M
18.0-12D-M
20.0-4D-J
20.0-5D-J
20.0-6D-J
20.0-8D-M
20.0-10D-M
20.0-12D-M
22.0-3D-J
22.0-4D-J
22.0-5D-J
SAP No.
20179043
20179037
20179038
20179055
20179056
20179057
20179058
20179059
20179053
20179054
20179071
20179074
20179077
20179080
20179085
20179062
20179064
20179089
20179090
20179091
20179092
20179087
20179088
20179101
20179103
20179105
20179107
20179110
20179094
20179096
20179134
20179137
20179140
20179145
20179123
20179125
20179149
20179150
20179151
Wt.*
149.7
257.2
281.2
80.4
92.8
108.0
132.9
159.2
275.5
300.4
84.3
97.1
113.1
139.0
166.3
253.2
278.9
110.9
128.1
145.3
176.3
261.0
288.6
109.0
129.0
144.9
165.0
242.1
276.3
308.1
135.4
154.6
173.7
271.4
311.7
351.8
126.7
159.8
181.4
Part No.
SAP No.
22.0-6D-M
22.0-8D-M
22.0-10D-M
22.0-12D-M
24.0-3D-J
24.0-4D-J
24.0-5D-J
24.0-6D-M
27.0-3D-J
27.0-4D-J
27.0-5D-M
27.0-6D-M
27.0-8D-M
27.0-10D-M
27.0-12D-N
33.0-3D-J
33.0-4D-M
33.0-5D-M
33.0-6D-M
33.0-8D-M
33.0-10D-N
33.0-12D-N
40.0-3D-J
40.0-4D-M
40.0-5D-M
40.0-6D-M
40.0-8D-N
40.0-10D-N
40.0-12D-P
48.0-5D-M
48.0-6D-M
48.0-8D-N
48.0-10D-P
48.0-12D-P
58.0-5D-M
58.0-6D-N
58.0-8D-N
58.0-10D-P
58.0-12D-P
20179152
20179153
20179147
20179148
20179158
20179160
20179162
20179164
20179181
20179183
20179185
20179187
20179190
20179177
20179178
20179232
20179233
20179234
20179235
20179236
20179230
20179231
20179287
20179288
20179289
20179290
20179291
20179285
20179286
20179303
20179304
20179305
20179301
20179302
20179362
20179363
20179364
20179360
20179361
Wt.*
250.9
318.5
368.3
412.2
140.3
176.3
200.2
278.4
167.5
199.5
290.1
319.6
391.7
450.8
560.0
218.9
315.0
352.9
427.7
489.3
641.7
729.3
267.4
380.1
445.4
498.4
653.3
814.0
938.3
586.8
660.6
820.8
987.0
1175.4
698.2
862.9
1063.6
1253.0
1454.8
V - B E L T
Part No.
*Weight does not include bushing and is approximate.
85
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
QT Sheaves - Single A Groove
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
AK30-QT
AK32-QT
AK34-QT
AK39-QT
AK41-QT
AK44-QT
AK46-QT
AK49-QT
AK51-QT
AK54-QT
AK56-QT
20179574
20179575
20179576
20179577
20179578
20179579
20179580
20179581
20179582
20179583
20179584
1.1
1.2
1.2
1.4
1.6
1.9
1.9
2.1
2.3
2.0
2.3
AK59-QT
AK61-QT
AK64-QT
AK66-QT
AK69-QT
AK71-QT
AK74-QT
AK79-QT
AK84-QT
AK89-QT
20179585
20179586
20179587
20179588
20179589
20179590
20179591
20179592
20179593
20179594
2.4
2.5
2.7
2.8
3.2
3.1
3.3
3.5
3.6
4.0
Part No.
SAP No.
Wt.*
AK94-QT
AK99-QT
AK104-QT
AK109-QT
AK114-QT
AK124-QT
AK134-QT
AK144-QT
AK154-QT
AK184-QT
20179595
20179596
20179566
20179567
20179568
20179569
20179570
20179571
20179572
20179573
4.4
4.7
4.5
5.1
5.5
6.1
7.4
7.8
8.8
11.3
QT Sheaves - Two A Groove
V - B E L T
Part No.
SAP No.
Wt.*
2AK30-QT
2AK32-QT
2AK34-QT
2AK39-QT
2AK41-QT
2AK44-QT
2AK46-QT
2AK49-QT
20179524
20179525
20179526
20179527
20179528
20179529
20179530
20179531
1.4
1.7
1.8
1.8
1.9
2.4
2.5
3.1
Part No.
SAP No.
Wt.*
2AK51-QT
2AK54-QT
2AK56-QT
2AK59-QT
2AK61-QT
2AK64-QT
2AK74-QT
2AK84-QT
20179532
20179533
20179534
20179535
20179536
20179537
20179538
20179539
3.2
3.4
3.6
3.4
4.4
3.9
4.9
4.8
Part No.
SAP No.
Wt.*
2AK94-QT
2AK104-QT
2AK114-QT
2AK124-QT
2AK134-QT
2AK144-QT
2AK154-QT
2AK184-QT
20179540
20179517
20179518
20179519
20179520
20179521
20179522
20179523
6.1
7.7
8.5
9.5
11.4
11.9
13.3
16.8
QT Sheaves — Single B Groove
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
BK30-QT
BK32-QT
BK34-QT
BK36-QT
BK40-QT
BK45-QT
BK47-QT
BK50-QT
BK52-QT
BK55-QT
BK57-QT
20179607
20179608
20179609
20179610
20179611
20179612
20179613
20179614
20179615
20179616
20179617
1.2
1.4
1.6
1.2
1.4
1.8
2.2
2.0
2.1
2.7
2.7
BK60-QT
BK62-QT
BK65-QT
BK67-QT
BK70-QT
BK72-QT
BK75-QT
BK77-QT
BK80-QT
BK85-QT
BK90-QT
20179618
20179619
20179620
20179621
20179622
20179623
20179624
20179625
20179626
20179627
20179628
2.5
2.6
2.8
2.9
2.8
3.1
3.3
3.6
3.4
3.6
4.3
*Weight does not include bushing and is approximate.
86
Part No.
SAP No.
Wt.*
BK95-QT
BK100-QT
BK105-QT
BK110-QT
BK115-QT
BK120-QT
BK130-QT
BK140-QT
BK150-QT
BK160-QT
BK190-QT
20179629
20179597
20179598
20179599
20179600
20179601
20179602
20179603
20179604
20179605
20179606
5.0
5.2
5.5
6.0
6.4
6.9
6.9
8.5
9.5
9.8
12.8
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
QT Sheaves - Two B Groove
Part No.
SAP No.
Wt.*
2BK32-QT
2BK34-QT
2BK36-QT
2BK40-QT
2BK45-QT
2BK47-QT
2BK50-QT
2BK52-QT
2BK55-QT
20179548
20179549
20179550
20179551
20179552
20179553
20179554
20179555
20179556
2.0
2.4
2.0
2.4
3.0
2.8
3.3
3.6
3.9
Part No.
SAP No.
Wt.*
2BK57-QT
2BK60-QT
2BK62-QT
2BK65-QT
2BK67-QT
2BK70-QT
2BK72-QT
2BK80-QT
20179557
20179558
20179559
20179560
20179561
20179562
20179563
20179564
4.3
4.4
4.5
4.5
5.0
5.1
5.4
6.4
Part No.
SAP No.
Wt.*
2BK90-QT
2BK100-QT
2BK110-QT
2BK120-QT
2BK130-QT
2BK140-QT
2BK160-QT
2BK190-QT
20179565
20179541
20179542
20179543
20179544
20179545
20179546
20179547
7.6
8.4
9.3
11.0
13.1
14.8
17.5
21.5
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
AK15-1/2
AK15-5/8
AK16-1/2
AK16-5/8
AK17-1/2
AK17-5/8
AK17-3/4
AK18-5/8
AK19-1/2
AK19-5/8
AK19-3/4
AK19-7/8
AK20-1/2
AK20-5/8
AK20-3/4
AK21-1/2
AK21-5/8
AK21-3/4
AK22-1/2
AK22-5/8
AK22-3/4
AK22-7/8
AK23-1/2
AK23-5/8
AK23-3/4
AK24-1/2
AK24-5/8
AK24-3/4
AK24-7/8
AK24-1
AK25-1/2
AK25-5/8
AK25-3/4
20179929
20179930
20179935
20179936
20179937
20179939
20179938
20179940
20179945
20179947
20179946
20179948
20179949
20179951
20179950
20179952
20179954
20179953
20179955
20179957
20179956
20179958
20179959
20179961
20179960
20179963
20179965
20179964
20179966
20179962
20179967
20179969
20179968
0.3
1.3
2.3
3.3
4.3
5.3
6.3
7.3
8.3
9.3
10.3
11.3
12.3
13.3
14.3
15.3
16.3
17.3
18.3
19.3
20.3
21.3
22.3
23.3
24.3
25.3
26.3
27.3
28.3
29.3
30.3
31.3
32.3
AK25-7/8
AK26-1/2
AK26-5/8
AK26-3/4
AK27-1/2
AK27-5/8
AK27-3/4
AK27-1
AK28-1/2
AK28-5/8
AK28-3/4
AK28-7/8
AK30-1/2
AK30-5/8
AK30-3/4
AK30-7/8
AK30-1
AK32-1/2
AK32-5/8
AK32-3/4
AK32-7/8
AK32-1
AK34-1/2
AK34-5/8
AK34-3/4
AK34-7/8
AK34-1
AK35-1/2
AK35-5/8
AK35-3/4
AK35-7/8
AK35-1
AK39-1/2
20179970
20179971
20179973
20179972
20179975
20179977
20179976
20179974
20179979
20179981
20179980
20179982
20179984
20179986
20179985
20179987
20179983
20179989
20179991
20179990
20179992
20179988
20179996
20179998
20179997
20179999
20179994
20180001
20180003
20180002
20180004
20180000
20180006
33.3
34.3
35.3
36.3
37.3
38.3
39.3
40.3
41.3
42.3
43.3
44.3
45.3
46.3
47.3
48.3
49.3
50.3
51.3
52.3
53.3
54.3
55.3
56.3
57.3
58.3
59.3
60.3
61.3
62.3
63.3
64.3
65.3
AK39-5/8
AK39-3/4
AK39-7/8
AK39-15/16
AK39-1
AK41-1/2
AK41-5/8
AK41-3/4
AK41-7/8
AK41-15/16
AK41-1
AK41-1 1/8
AK44-1/2
AK44-5/8
AK44-3/4
AK44-7/8
AK44-15/16
AK44-1
AK44-1 1/8
AK46-1/2
AK46-5/8
AK46-3/4
AK46-7/8
AK46-15/16
AK46-1
AK46-1 1/8
AK49-1/2
AK49-5/8
AK49-3/4
AK49-7/8
AK49-15/16
AK49-1
AK49-1 1/8
20180008
20180007
20180009
20180011
20180005
20180014
20180017
20180016
20180018
20180015
20180012
20180013
20180021
20180023
20180022
20180024
20180025
20180019
20180020
20180028
20180030
20180029
20180031
20180032
20180026
20180027
20180035
20180038
20180037
20180039
20180036
20180033
20180034
66.3
67.3
68.3
69.3
70.3
71.3
72.3
73.3
74.3
75.3
76.3
77.3
78.3
79.3
80.3
81.3
82.3
83.3
84.3
85.3
86.3
87.3
88.3
89.3
90.3
91.3
92.3
93.3
94.3
95.3
96.3
97.3
98.3
V - B E L T
FH P B o r e d - t o - S i z e
Single A Groove Sheaves
continued on page 88
*Weight does not include bushing and is approximate.
87
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
FH P B o r e d - t o - S i z e
Single A Groove Sheaves
V - B E L T
Part No.
SAP No.
AK51-1/2
AK51-5/8
AK51-3/4
AK51-7/ 8
AK51-1
AK51-1 1/8
AK54-1/2
AK54-5/8
AK54-3/4
AK54-7/8
AK54-15/16
AK54-1
AK54-1 1/8
AK54-1 3/16
AK56-1/2
AK56-5/8
AK56-3/4
AK56-7/8
AK56-15/16
AK56-1
AK56-1 1/8
AK56-1 3/16
AK59-1/2
AK59-5/8
AK59-3/4
AK59-7/8
AK59-15/16
AK59-1
AK59-1-1/8
AK59-1 3/16
AK61-1/2
AK61-5/8
AK61-3/4
AK61-7/8
AK61-15/16
AK61-1
AK61-1 1/8
AK61-1 3/16
AK64-1/2
AK64-5/8
AK64-3/4
AK64-7/8
AK64-15/16
AK64-1
AK64-1 1/8
AK64-1 3/16
20180042
20180044
20180043
20180045
20180040
20180041
20180048
20180051
20180050
20180052
20180049
20180046
20180053
20180047
20180057
20180059
20180058
20180060
20180061
20180054
20180055
20180056
20180064
20180067
20180066
20180068
20180069
20180062
20180065
20180063
20180073
20180075
20180074
20180076
20180077
20180070
20180071
20180072
20180081
20180083
20180082
20180084
20180085
20180078
20180079
20180080
Wt.*
99.3
100.3
101.3
102.3
103.3
104.3
105.3
106.3
107.3
108.3
109.3
110.3
111.3
112.3
113.3
114.3
115.3
116.3
117.3
118.3
119.3
120.3
121.3
122.3
123.3
124.3
125.3
126.3
127.3
128.3
129.3
130.3
131.3
132.3
133.3
134.3
135.3
136.3
137.3
138.3
139.3
140.3
141.3
142.3
143.3
144.3
Part No.
SAP No.
Wt.*
AK66-5/8
AK66-3/4
AK66-1
AK66-1 1/8
AK69-3/4
AK69-1
AK69-1 1/8
AK71-1/2
AK71-5/8
AK71-3/4
AK71-1
AK71-1 1/8
AK71-1 7/16
AK74-1/2
AK74-5/8
AK74-3/4
AK74-15/16
AK74-1
AK74-1 1/8
AK74-1 3/16
AK74-1 1/4
AK74-1 7/16
AK79-3/4
AK79-1
AK79-1 1/8
AK79-1 7/16
AK81-5/8
AK81-3/4
AK81-1
2AK84-1 3/16
AK84-1/2
AK84-5/8
AK84-3/4
AK84- 15/16
AK84-1
AK84-1 3/16
AK84-1 7/16
AK89-3/4
AK89-1
AK89-1 1/8
AK89-1 7/16
AK91-3/4
AK91-1
AK94-1/2
AK94-5/8
AK94-3/4
20180089
20180088
20180086
20180087
20180092
20180090
20180091
20180096
20180098
20180097
20180093
20180094
20180095
20180104
20180106
20180105
20180107
20180099
20180101
20180102
20180100
20180103
20180110
20180108
20180109
20180111
20180115
20180114
20180112
20179764
20180120
20180122
20180121
20180116
20180117
20180118
20180119
20180126
20180123
20180124
20180125
20180128
20180127
20180133
20180135
20180134
145.3
146.3
147.3
148.3
149.3
150.3
151.3
152.3
153.3
154.3
155.3
156.3
157.3
158.3
159.3
160.3
161.3
162.3
163.3
164.3
165.3
166.3
167.3
168.3
169.3
170.3
171.3
172.3
173.3
174.3
175.3
176.3
177.3
178.3
179.3
180.3
181.3
182.3
183.3
184.3
185.3
186.3
187.3
188.3
189.3
190.3
*Weight does not include bushing and is approximate.
88
Part No.
SAP No.
AK94-15/16
AK94-1
AK94-1 3/16
AK94-1 1/4
AK94-1 7/16
AK99-3/4
AK99-1
AK99-1 7/16
AK104-5/8
AK104-3/4
AK104-1
AK104-1-3/16
AK104-1-1/4
AK104-1-3/8
AK104-1-7/16
AK109-3/4
AK109-1
AK109-1 3/8
AK109-1-7/16
AK114-3/4
AK114-1
AK114-1-3/16
AK114-1-7/16
AK124-5/8
AK124-3/4
AK124-1
AK124-1 3/16
AK124-1-1/4
AK124-1-7/16
AK134-3/4
AK134-1
AK134-1-3/16
AK134-1-3/8
AK134-1-7/16
AK144-3/4
AK144-1
AK144-1-3/16
AK144-1-7/16
AK154-3/4
AK154-1
AK154-1-7/16
AK184-3/4
AK184-1
AK184-1-3/16
AK184-1-7/16
20180136
20180129
20180131
20180130
20180132
20180139
20180137
20180138
20179903
20179902
20179897
20179899
20179898
20179900
20179901
20179906
20179904
20179907
20179905
20179911
20179908
20179909
20179910
20179917
20179916
20179912
20179913
20179914
20179915
20179922
20179918
20179919
20179920
20179921
20179928
20179925
20179926
20179927
20179934
20179931
20179933
20179944
20179941
20179942
20179943
Wt.*
191.3
192.3
193.3
194.3
195.3
196.3
197.3
198.3
199.3
200.3
201.3
202.3
203.3
204.3
205.3
206.3
207.3
208.3
209.3
210.3
211.3
212.3
213.3
214.3
215.3
216.3
217.3
218.3
219.3
220.3
221.3
222.3
223.3
224.3
225.3
226.3
227.3
228.3
229.3
230.3
231.3
232.3
233.3
234.3
235.3
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
Part No.
SAP No.
Wt.*
BK19-5/8
BK19-3/4
BK22-1/2
BK22-5/8
BK22-3/4
BK22-7/8
BK22-1
BK23-5/8
BK23-1
BK24-1/2
BK24-5/8
BK24-3/4
BK24-7/8
BK24-1
BK25-1/2
BK25-5/8
BK25-3/4
BK25-7/8
BK26-1/2
BK26-5/8
BK26-3/4
BK26-7/8
BK27-1/2
BK27-5/8
BK27-3/4
BK27-7/8
BK27-1 1/8
BK28-1/2
BK28-5/8
BK28-3/4
BK28-7/8
BK28-1
BK28-1 1/8
BK30-1/2
BK30-5/8
BK30-3/4
BK30-7/8
BK30-1
BK30-1 1/8
BK32-1/2
BK32-5/8
BK32-3/4
BK32-7/8
BK32-1
BK34-1/2
BK34-5/8
BK34-3/4
BK34-7/8
BK34-1
20180181
20180180
20180190
20180192
20180191
20180193
20180189
20180194
20180195
20180200
20180202
20180201
20180203
20180199
20180204
20180206
20180205
20180207
20180208
20180210
20180209
20180211
20180213
20180215
20180214
20180216
20180212
20180219
20180221
20180220
20180222
20180217
20180218
20180225
20180227
20180226
20180228
20180223
20180224
20180236
20180238
20180237
20180239
20180235
20180242
20180244
20180243
20180245
20180240
0.7
0.7
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.1
1.1
1.1
1.1
1.1
1.4
1.4
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.8
1.8
1.8
1.8
1.8
Part No.
SAP No.
Wt.*
BK34-1 1/8
BK36-1/2
BK36-5/8
BK36-3/4
BK36-7/8
BK36-1
BK36-1 1/8
BK40-1/2
BK40-5/8
BK40-3/4
BK40-7/8
BK40-1
BK40-1 1/8
BK45-1/2
BK45-5/8
BK45-3/4
BK45-7/8
BK45-1
BK45-1 1/ 8
BK46-7/8
BK47-1/2
BK47-5/8
BK47-3/4
BK47-7/8
BK47-1
BK47-1 1/8
BK48-5/8
BK48-3/4
BK48-7/8
BK48-1 1/8
BK50-1/2
BK50-5/8
BK50-3/4
BK50-7/8
BK50-15/16
BK50-1
BK50-1 1/8
BK52-1/2
BK52-5/8
BK52-3/4
BK52-7/8
BK52-1
BK52-1 1/8
BK55-1/2
BK55-5/8
BK55-3/4
BK55-7/8
BK55-1
BK55-1 1/8
20180241
20180248
20180250
20180249
20180251
20180246
20180247
20180254
20180256
20180255
20180257
20180252
20180253
20180260
20180262
20180261
20180263
20180258
20180259
20180264
20180267
20180269
20180268
20180270
20180265
20180266
20180273
20180272
20180274
20180271
20180277
20180279
20180278
20180280
20180281
20180275
20180276
20180284
20180286
20180285
20180287
20180282
20180283
20180291
20180293
20180292
20180294
20180288
20180289
1.8
2.0
2.0
2.0
2.0
2.0
2.0
2.2
2.2
2.2
2.2
2.2
2.2
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.9
2.9
2.9
2.9
2.9
2.9
3.0
3.0
3.0
3.0
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.4
3.4
3.4
3.4
3.4
3.4
4.0
4.0
4.0
4.0
4.0
4.0
Part No.
SAP No.
Wt.*
BK55-1 3/16
BK57/HA54 5/8
BK57-3/4
BK57-7/8
BK57-15/16
BK57-1
BK57-1 1/8
BK60-1/2
BK60-5/8
BK60-3/4
BK60-7/8
BK60-1
BK60-1-1/8
BK60-1 3/16
BK62-1/2
BK62-5/8
BK62-3/4
BK62-7/8
BK62-15/16
BK62-1
BK62-1 1/8
BK62-1 13/16
BK64-5/8
BK64-3/4
BK64-7/8
BK65-5/8
BK65-3/4
BK65-1
BK65-1 1/8
BK67-5/8
BK67-3/4
BK67-1
BK67-1 1/8
BK70-5/8
BK70-3/4
BK70-15/16
BK70-1
BK70-1-1/8
BK70-1 13/16
BK70-1-7/16
BK72-3/4
BK72-1
BK72-1-1/8
BK72-1-3/8
BK72-1 7/16
BK75-3/4
BK75-1
BK75-1 1/8
BK75-1 7/16
20180290
20180295
20180298
20180299
20180300
20180296
20180297
20180303
20180306
20180305
20180307
20180301
20180304
20180302
20180311
20180313
20180312
20180314
20180315
20180308
20180309
20333018
20180318
20333019
20180319
20180323
20180322
20180320
20180321
20180327
20180326
20180324
20333020
20180335
20180334
20180336
20180330
20180332
20333021
20180333
20180341
20180337
20180339
20180340
20180338
20180345
20180342
20180343
20180344
4.0
4.1
4.1
4.1
4.1
4.1
4.1
3.8
3.8
3.8
3.8
3.8
3.8
3.8
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.7
3.8
3.8
3.8
3.8
3.8
4.3
4.3
4.3
4.3
V - B E L T
FH P B o r e d - t o - S i z e
Single B Groove Sheaves
continued on page 90
*Weight does not include bushing and is approximate.
89
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
FH P B o r e d - t o - S i z e
Single B Groove Sheaves
V - B E L T
Part No.
SAP No.
Wt.*
BK77-3/4
BK77-1
BK77-1 1/8
BK77-1 3/8
BK77-1 7/16
BK80-5/8
BK80-3/4
BK80-7/8
BK80-1
BK80-1 1/8
BK85-1 3/16
BK80-1 1/4
BK80-1 3/8
BK80-1 7/16
BK85-3/4
BK85-1
BK85-1 1/8
BK85-1 13/16
BK85-1 3/8
BK85-1-7/16
BK90-3/4
BK90-7/8
BK90-15/16
BK90-1
BK90-1-1/8
BK90-1-3/16
BK90-1-3/8
20180350
20180346
20180347
20180348
20180349
20180358
20180357
20180359
20180351
20180353
20180362
20180352
20180355
20180356
20180365
20180360
20180361
20333022
20180363
20180364
20180370
20180371
20180373
20180366
20180367
20180368
20180369
4.5
4.5
4.5
4.5
4.5
5.1
5.1
5.1
5.1
5.1
5.1
5.1
5.1
5.1
5.5
5.5
5.5
5.5
5.5
5.5
6.0
6.0
6.0
6.0
6.0
6.0
6.0
Part No.
SAP No.
Wt.*
BK90-1 7/16
BK92-3/4
BK92-7/8
BK92-1 1/8
BK95-3/4
BK95-1
BK95-1-1/8
BK95-1-3/8
BK95-1 7/16
BK100-3/4
BK100-7/8
BK100-1
BK100-1 1/8
BK100-1 3/16
BK100-1-1/4
BK100-1-3/8
BK100-1 7/16
BK105-1
BK105-1 3/8
BK105-1 7/16
BK110-3/4
BK110-1
BK110-1 1/8
BK110-1 13/16
BK110-1-3/8
BK110-1-7/16
20180372
20180379
20180380
20180376
20180385
20180381
20180383
20180384
20180382
20180146
20180147
20180140
20180141
20180142
20180144
20180145
20180143
20180148
20180149
20180150
20180156
20180151
20180152
20333023
20180154
20180155
6.0
6.2
6.2
6.2
6.3
6.3
6.3
6.3
6.3
7.2
7.2
7.2
7.2
7.2
7.2
7.2
7.2
7.7
7.7
7.7
8.2
8.2
8.2
8.2
8.2
8.2
Part No.
SAP No.
Wt.*
BK115-1
BK115-1 3/8
BK115-1 7/16
BK120-3/4
BK120-1
BK120-1 13/16
BK120-1-3/8
BK120-1 7/16
BK130-3/4
BK130-1
BK130-1 1/8
BK130-1 13/16
BK130-1-7/16
BK140-3/4
BK140-1
BK140-1 13/16
BK140-1-7/16
BK160-1
BK160-1 1/8
BK160-1 13/16
BK160-1 1/4
BK160-1 7/16
BK190-1
BK190-1 13/16
BK190-1 1/4
BK190-1-7/16
20180157
20180158
20180159
20180164
20180160
20333024
20180163
20180162
20180168
20180165
20180170
20333025
20180167
20180174
20180171
20333026
20180173
20180175
20180177
20333027
20180176
20180179
20180182
20333028
20180183
20180184
8.7
8.7
8.7
9.2
9.2
9.2
9.2
9.2
9.6
9.6
9.6
9.6
9.6
11.2
11.2
11.2
11.2
12.9
12.9
12.9
12.9
12.9
14.5
14.5
14.5
14.5
FH P B o r e d - t o - S i z e
Two A Groove Sheaves
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
2AK20-1/2
2AK20-5/8
2AK20-3/4
2AK21-1/2
2AK21-5/8
2AK21-3/4
2AK22-1/2
2AK22-5/8
2AK22-3/4
2AK22-7/8
2AK22-1
2AK23-5/8
20179650
20179652
20179651
20179654
20179656
20179655
20179657
20179659
20179658
20179660
20179661
20179664
0.9
0.9
0.9
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.2
1.3
2AK23-3/4
2AK23-7/8
2AK23-1
2AK25-5/8
2AK25-3/4
2AK25-7/8
2AK25-1
2AK26-5/8
2AK26-3/4
2AK26-7/8
2AK27-5/8
2AK27-3/4
20179663
20179665
20179662
20179668
20179667
20179669
20179666
20179672
20179671
20179673
20179676
20179675
1.3
1.3
1.3
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.8
1.8
*Weight does not include bushing and is approximate.
90
Part No.
SAP No.
Wt.*
2AK27-7/8
2AK27-1
2AK28-5/8
2AK28-3/4
2AK28-7/8
2AK28-1
2AK30-1/2
2AK30-5/8
2AK30-3/4
2AK30-7/8
2AK30-1
2AK30-1 1/8
20179677
20179674
20179681
20179680
20179682
20179679
20179685
20179687
20179686
20179688
20179683
20179684
1.8
1.8
2.0
2.0
2.0
2.0
2.2
2.2
2.2
2.2
2.2
2.2
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
Part No.
SAP No.
Wt.*
2AK32-5/8
2AK32-3/4
2AK32-7/8
2AK32-1
2AK32-1 1/8
2AK34-5/8
2AK34-3/4
2AK34-7/8
2AK34-1
2AK34-1 1/8
2AK39-5/8
2AK39-3/4
2AK39-7/8
2AK39-1
2AK39-1 1/8
2AK41-5/8
2AK41-3/4
2AK41-7/8
2AK41-1
2AK41-1 1/8
2AK44-5/8
2AK44-3/4
2AK44-7/8
2AK44-1
2AK44-1 1/8
2AK46-5/8
2AK46-7/8
2AK46-1
2AK46-1 1/8
2AK49-3/4
2AK49-7/8
2AK49-1
2AK49-1 1/8
2AK49-1 3/8
20179692
20179691
20179693
20179689
20179690
20179697
20179696
20179698
20179694
20179695
20179702
20179701
20179703
20179699
20179700
20179707
20179706
20179708
20179704
20179705
20179712
20179711
20179713
20179709
20179710
20179716
20179717
20179714
20179715
20179720
20179721
20179718
20179719
20179722
2.4
2.4
2.4
2.4
2.4
2.7
2.7
2.7
2.7
2.7
3.2
3.2
3.2
3.2
3.2
3.5
3.5
3.5
3.5
3.5
4.1
4.1
4.1
4.1
4.1
4.6
4.6
4.6
4.6
2.7
2.7
2.7
2.7
2.7
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
2AK51-3/4
2AK51-7/8
2AK51-1
2AK51-1 1/8
2AK51-1-3/8
2AK54-5/8
2AK54-3/4
2AK54-7/8
2AK54-1
2AK54-1 1/8
2AK54-1 3/8
2AK56-5/8
2AK56-3/4
2AK56-1
2AK56-1 1/8
2AK56-1-3/8
2AK59-1
2AK59-1 1/8
2AK59-1-3/8
2AK61-3/4
2AK61-7/8
2AK61-1
2AK61-1 1/8
2AK61-1-3/8
2AK64-3/4
2AK64-1
2AK64-1 1/8
2AK64-1-3/16
2AK64-1-3/8
2AK64-1-7/16
2AK74-3/4
2AK74-1
2AK74-1-1/8
2AK74-1-3/16
20179726
20179727
20179723
20179724
20179725
20179731
20179730
20179732
20179728
20179729
20179733
20179738
20179737
20179734
20179735
20179736
20179739
20179740
20179741
20179745
20179746
20179742
20179743
20179744
20179752
20179747
20179748
20179749
20179750
20179751
20179758
20179753
20179754
20179755
2.9
2.9
2.9
2.9
2.9
3.2
3.2
3.2
3.2
3.2
3.2
3.3
3.3
3.3
3.3
3.3
3.4
3.4
3.4
3.6
3.6
3.6
3.6
3.6
4.5
4.5
4.5
4.5
4.5
4.5
5.8
5.8
5.8
5.8
2AK74-1-3/8
2AK74-1-7/16
2AK84-3/4
2AK84-15/16
2AK84-1
2AK84-1-1/8
2AK84-1-3/8
2AK84-1-7/16
2AK94-3/4
2AK94-1
2AK94-1-1/8
2AK94-1-3/16
2AK94-1-3/8
2AK94-1-7/16
2AK104-3/4
2AK104-15/16
2AK104-1
2AK104-1 3/16
2AK104-1-7/16
2AK114-1
2AK114-1-3/16
2AK114-1-3/8
2AK114-1-7/16
2AK124-1
2AK124-1-3/16
2AK124-1-7/16
2AK134-1-3/16
2AK134-1-7/16
2AK144-1
2AK144-1 7/16
2AK154-1 3/16
2AK154-1 7/16
2AK184-1-3/16
2AK184-1-7/16
20179756
20179757
20179763
20179765
20179759
20179760
20179761
20179762
20179771
20179766
20179767
20179768
20179769
20179770
20179633
20179634
20179630
20179631
20179632
20179635
20179636
20179637
20179638
20179639
20179640
20179641
20179642
20179643
20179644
20179645
20179646
20179647
20179648
20179649
5.8
5.8
6.9
6.9
6.9
6.9
6.9
6.9
7.7
7.7
7.7
7.7
7.7
7.7
9.7
9.7
9.7
9.7
9.7
10.2
10.2
10.2
10.2
11.3
11.3
11.3
12.4
12.4
13.2
13.2
13.7
13.7
15.8
15.8
V - B E L T
FH P B o r e d - t o - S i z e
Two A Groove Sheaves
FH P B o r e d - t o - S i z e
Two B Groove Sheaves
Part No.
SAP No.
Wt.*
2BK23-5/8
2BK23-7/8
2BK25-1/2
2BK25-5/8
2BK25-3/4
20179794
20179795
20179796
20179798
20179797
1.3
1.3
1.4
1.4
1.4
Part No.
SAP No.
Wt.*
2BK25-7/8
2BK26-5/8
2BK26-7/8
2BK26-1 1/8
2BK27-1/2
20179799
20179802
20179803
20179801
20179804
1.4
1.6
1.6
1.6
1.8
*Weight does not include bushing and is approximate.
Part No.
SAP No.
Wt.*
2BK27-5/8
2BK27-3/4
2BK27-7/8
2BK27-1
2BK28-1/2
20179806
20179805
20179808
20179807
20179811
1.8
1.8
1.8
1.8
1.9
continued on page 93
91
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
FH P B o r e d - t o - S i z e
Two B Groove Sheaves
V - B E L T
Part No.
SAP No.
Wt.*
2BK28-5/8
2BK28-3/4
2BK28-7/8
2BK28-1
2BK28-1 1/8
2BK30-1/2
2BK30-5/8
2BK30-3/4
2BK30-7/8
2BK30-1
2BK30-1 1/8
2BK32-5/8
2BK32-7/8
2BK32-1
2BK32-1 1/8
2BK34-5/8
2BK34-3/4
2BK34-7/8
2BK34-1
2BK34-1 1/8
2BK36-3/4
2BK36-7/8
2BK36-1
2BK36-1 1/8
2BK36-1 3/8
2BK40-5/8
2BK40-3/4
2BK40-7/8
2BK40-1
2BK40-1 1/8
2BK45-1
2BK45-1 1/8
2BK45-1 3/8
2BK47-7/8
2BK47-1
20179813
20179812
20179814
20179809
20179810
20179817
20179819
20179818
20179820
20179815
20179816
20179824
20179825
20179821
20179822
20179829
20179828
20179830
20179826
20179827
20179834
20179835
20179831
20179832
20179833
20179840
20179839
20179841
20179837
20179838
20179843
20179844
20179845
20179849
20179847
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.2
2.2
2.2
2.2
2.4
2.4
2.4
2.4
2.4
3.0
3.0
3.0
3.0
3.0
4.0
4.0
4.0
4.0
4.0
4.5
4.5
4.5
5.1
5.1
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
2BK47-1 1/8
2BK50-3/4
2BK50-1
2BK50-1 1/8
2BK50-1 3/8
2BK52-7/8
2BK52-1
2BK52-1 1/8
2BK52-1 3/8
2BK55-1 1/8
2BK55-1 3/8
2BK57-1
2BK57-1 1/8
2BK57-1 3/8
2BK60-3/4
2BK60-7/8
2BK60-1
2BK60-1 1/8
2BK60-1 3/8
2BK62-1
2BK62-1 1/8
2BK62-1 3/8
2BK65-1
2BK65-1 1/8
2BK65-1 3/8
2BK67-1
2BK67-1 1/8
2BK67-1 3/8
2BK70-3/4
2BK70-1
2BK70-1 1/8
2BK70-1 3/16
2BK70-1 3/8
2BK70-1 7/16
20179848
20179853
20179850
20179851
20179852
20179857
20179854
20179855
20179856
20179860
20179861
20179862
20179863
20179864
20179868
20179869
20179865
20179866
20179867
20179870
20179871
20179872
20179873
20179874
20179875
20179876
20179877
20179878
20179882
20179879
20179880
20179883
20179881
20179884
5.1
5.4
5.4
5.4
5.4
5.7
5.7
5.7
5.7
6.5
6.5
6.0
6.0
6.0
6.3
6.3
6.3
6.3
6.3
7.6
7.6
7.6
5.2
5.2
5.2
5.8
5.8
5.8
5.6
5.6
5.6
5.6
5.6
5.6
2BK80-3/4
2BK80-1
2BK80-1 1/8
2BK80-1 3/16
2BK80-1 3/8
2BK80-1 7/16
2BK90-3/4
2BK90-1
2BK90-1 1/8
2BK90-1 3/16
2BK90-1 3/8
2BK90-1 7/16
2BK100-3/4
2BK100-1
2BK100-1 3/16
2BK100-1 3/8
2BK100-1 7/16
2BK110-1
2BK110-1 3/16
2BK110-1 7/16
2BK120-1
2BK120-1 3/16
2BK120-1 7/16
2BK130-1
2BK130-1 3/16
2BK130-1 7/16
2BK140-1
2BK140-1 3/16
2BK140-1 7/16
2BK160-1
2BK160-1 3/16
2BK160-1 7/16
2BK190-1 3/16
2BK190-1 7/16
20179890
20179885
20179886
20179887
20179888
20179889
20179896
20179891
20179892
20333029
20333030
20333031
20179776
20179772
20179773
20333032
20179774
20179777
20179778
20179779
20179780
20179781
20179782
20179783
20179784
20179785
20179786
20179787
20179788
20179789
20179790
20179791
20179792
20179793
6.9
6.9
6.9
6.9
6.9
6.9
8.0
8.0
8.0
8.0
8.0
8.0
9.5
9.5
9.5
9.5
9.5
11.4
11.4
11.4
13.2
13.2
13.2
14.8
14.8
14.8
15.6
15.6
15.6
18.5
18.5
18.5
21.5
21.5
L i g h t - D u t y ( FH P ) A d j u s t a b l e
VP Series Sheaves
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
1VP25-1/2
1VP25-5/8
1VP25-3/4
1VP30-1/2
1VP30-5/8
20180386
20180388
20180387
20180389
20180391
0.7
0.7
0.7
1.1
1.1
1VP30-3/4
1VP34-1/2
1VP34-5/8
1VP34-3/4
1VP34-7/8
20180390
20180394
20180396
20180395
20180397
1.1
1.4
1.4
1.4
1.4
1VP34-1
1VP34-1 1/8
1VP40-1/2
1VP40-5/8
1VP40-3/4
20180392
20180393
20180400
20180402
20180401
1.4
1.4
1.9
1.9
1.9
*Weight does not include bushing and is approximate.
92
continued on page 93
P O W E R
T R A N S M I S S I O N
P R O D U C T S V - B E L T
2 0 1 0
Part No.
SAP No.
Wt.*
1VP40-7/8
1VP40-1
1VP40-1 1/8
1VP44-1/2
1VP44-5/8
1VP44-3/4
1VP44-7/8
1VP44-1
1VP44-1 1/8
1VP50-1/2
1VP50-5/8
1VP50-3/4
1VP50-7/8
1VP50-1
1VP50-1 1/8
1VP56-1/2
1VP56-5/8
1VP56-3/4
1VP56-7/8
1VP56-1
1VP56-1 1/8
1VP60-5/8
1VP60-3/4
1VP60-7/8
1VP60-1
1VP60-1 1/8
1VP60-1 3/8
1VP62-5/8
1VP62-3/4
1VP62-7/8
1VP62-1
1VP62-1 1/8
1VP62-1 1/4
1VP62-1 3/8
1VP65-3/4
1VP65-7/8
1VP65-1 1/8
1VP65-1 3/8
1VP65-1 5/8
20180403
20180398
20180399
20180406
20180408
20180407
20180409
20180404
20180405
20180412
20180414
20180413
20180415
20180410
20180411
20180418
20180420
20180419
20180421
20180416
20180417
20180427
20180426
20180428
20180422
20180423
20180424
20180434
20180433
20180435
20180429
20180431
20180430
20180432
20180439
20180440
20180436
20180437
20180438
1.9
1.9
1.9
2.4
2.4
2.4
2.4
2.4
2.4
3.6
3.6
3.6
3.6
3.6
3.6
4.4
4.4
4.4
4.4
4.4
4.4
6.5
6.5
6.5
6.5
6.5
6.5
6.1
6.1
6.1
6.1
6.1
6.1
6.1
6.8
6.8
6.8
6.8
6.8
Part No.
SAP No.
Wt.*
Part No.
SAP No.
Wt.*
1VP68-5/8
1VP68-3/4
1VP68-7/8
1VP68-1
1VP68-1 1/8
1VP68-1 1/4
1VP68-1 3/8
1VP71-3/4
1VP71-7/8
1VP71-1 1/8
1VP71-1 3/8
1VP71-1 5/8
1VP75-3/4
1VP75-7/8
1VP75-1
1VP75-1 1/8
1VP75-1 3/8
1VP75-1 5/8
2VP36-1/2
2VP36-5/8
2VP36-3/4
2VP36-7/8
2VP36-1
2VP36-1 1/8
2VP42-5/8
2VP42-3/4
2VP42-7/8
2VP42-1
2VP42-1 1/8
2VP50-5/8
2VP50-3/4
2VP50-7/8
2VP50-1
2VP50-1 1/8
2VP56-5/8
2VP56-3/4
2VP56-7/8
2VP56-1
20180446
20180445
20180447
20180441
20180443
20180442
20180444
20180451
20180452
20180448
20180449
20180450
20180457
20180458
20180453
20180454
20180455
20180456
20333033
20180462
20180461
20180463
20180459
20180460
20180467
20180466
20180468
20180464
20180465
20180472
20180471
20180473
20180469
20180470
20180479
20180478
20180480
20180474
7.3
7.3
7.3
7.3
7.3
7.3
7.3
8.5
8.5
8.5
8.5
8.5
9.2
9.2
9.2
9.2
9.2
9.2
3.4
3.4
3.4
3.4
3.4
3.4
4.4
4.4
4.4
4.4
4.4
6.3
6.3
6.3
6.3
6.3
7.8
7.8
7.8
7.8
2VP56-1 1/8
2VP56-1 3/8
2VP56-1 5/8
2VP60-3/4
2VP60-7/8
2VP60-1
2VP60-1 1/8
2VP60-1 3/8
2VP60-1 5/8
2VP62-3/4
2VP62-7/8
2VP62-1
2VP62-1 1/8
2VP62-1 3/8
2VP62-1 5/8
2VP65-3/4
2VP65-7/8
2VP65-1 1/8
2VP65-1 3/8
2VP65-1 5/8
2VP68-3/4
2VP68-7/8
2VP68-1
2VP68-1 1/4
2VP68-1 1/8
2VP68-1 3/8
2VP68-1 5/8
2VP71-3/4
2VP71-7/8
2VP71-1 1/8
2VP71-1 3/8
2VP71-1 5/8
2VP75-3/4
2VP75-7/8
2VP75-1
2VP75-1 1/8
2VP75-1 3/8
2VP75-1 5/8
20180475
20180476
20180477
20180485
20180486
20180481
20180482
20180483
20180484
20180491
20180492
20180487
20180489
20180490
20333034
20180496
20180497
20180493
20180494
20180495
20180503
20180504
20180498
20180499
20180500
20180501
20180502
20180508
20180509
20180505
20180506
20180507
20180514
20180515
20180510
20180511
20180512
20180513
7.8
7.8
7.8
10.6
10.6
10.6
10.6
10.6
10.6
10.0
10.0
10.0
10.0
10.0
10.0
12.3
12.3
12.3
12.3
12.3
11.7
11.7
11.7
11.7
11.7
11.7
11.7
14.6
14.6
14.6
14.6
14.6
16.5
16.5
16.5
16.5
16.5
16.5
V - B E L T
L i g h t - D u t y ( FH P ) A d j u s t a b l e
VP Series Sheaves
*Weight does not include bushing and is approximate.
93
P O W E R
T R A N S M I S S I O N
B ushing
P R O D U C T S H ardware
Bushings
Sure-Grip® “Quick Detachable” bushings are easy to install and
remove. They are split through flange and taper to provide a true
clamp on the shaft that is the equivalent of a shrink fit. All sizes
except JA and QT have a setscrew over the key to help maintain
the bushing’s position on the shaft until the cap screws are securely
tightened. Sure-Grip bushings have a very gradual taper (3⁄4-inch
taper per ft. on the diameter) which is about half the inclined
angle of many other bushings. The result is that the Sure-Grip
securely clamps the shaft, with twice the force of those competitive
bushings, to provide extreme holding power.
Versatile Sure-Grip bushings permit the mounting of the same
mating part on shafts of different diameters, and the mounting
of different sheaves on the same shaft using the same bushing.
Their interchange ability extends through sheaves, pulleys, timing
pulleys, sprockets, flexible and rigid couplings, made-to-order items
by Veyance Technologies, and to product lines of several other
mechanical power transmission manufacturers.
6-hole drilling
(most sizes) makes
installation and
removal quick
and easy.
Precise taper (3⁄4 in. per ft.
on diameter) provides proper
wedging action.
Saw cut through flange
and taper (and sometimes
cut down into keyway
also) to provide a
true clamp fit.
Cap screws used
to secure bushings
to sheave and to
remove bushing
from sheave.
Keyseat 180°
from split.
Sure-Grip bushings are manufactured with the drilled and tapped
holes located at a precise distance from the keyseat; thus, a wide
mating part having a bushing in each end can be mounted on a
common shaft with the two keyways in line. This feature not only
facilitates installation but also permits both bushings to carry an
equal share of the load.
Available Sure-Grip Bushings
F
QT*
J
JA
M
SH
N
SDS
P
SK
W
SF
S
E
B ushing
Metric Sure-Grip Bushings
QTMX
SKMX
JAMX
SFMX
SHMX
EMX
SDSMX
FMX
SDMX
Available Sure-Grip Bushings
(Millimeter Bores-Inch Bolt)
QT
JA
SH
SDS
SD
SK
SF
E
F
J
M
N
P
SKL
SFL
EL
Metric “L” Series
Flangeless Bushings
SKLMX
ELMX
SFLMX
FLMX
H ardware
*“H” is a split Taper Bushing. “QT” is a QD® Bushing and is interchangeable with an “H” bushing.
SURE-GRIP is a trademark of TB Wood’s Incorporated
94
“L” Series Flangeless Bushings
EL
SKL
FL
SFL
Sure-Grip Idler Bushings &
Replacement Bearings
SH-BB
SF-BB
SD-BB
E-BB
SK-BB
Sure-Grip Short Bushings
JS
PS
MS
WS
NS
P O W E R
T R A N S M I S S I O N
B ushing
P R O D U C T S H ardware
2 0 1 0
G e n e r a l P r o d u ct I n f o
S u r e - G r ip ®* B u s h i n g s
• Sure-Grip bushings conform to the specifications set forth by
the Mechanical Power Transmission Association (MPTA) in
their CO-1 Guideline of October 1992.
dimensions. Square keys are used where possible. For larger
bores where a square key is not possible, the required rectangular
key is furnished with the bushing.
• An “MPB” or “Minimum Plain Bore” bushing is available
in most bushing sizes. These bushings are unsplit and have no
keyway. These bushings are intended for reboring and other
alterations.
• Sure-Grip bushings for metric shafts conform to British
Standard HS 4235: Part 1:1972 for key size versus shaft
diameter and keyway dimensions. For larger bores where it is not
possible to maintain the standard keyway depth, a more shallow
keyway may be used. Special metric keys are not furnished with
the bushing.
• Sure-Grip bushings for inch shafts conform to ANSI
B17.1-1967, R1989 for key size versus shaft diameter and keyway
Materials
Special Constructions Available
• The standard material is class 30 or higher cast iron. Products
made from cast iron have a maximum speed limitation of 6,500
foot/minute at the outside diameter. Higher speed requirements
dictate the use of higher strength materials.
• We have the capability to assist in your design and quote any
specially designed power transmission drive. We are able to offer
consistently competitive prices and fast delivery on the following
specials plus much more.
• For speeds up to 16,000 foot/minute or high shock application
requiring greater toughness, special ductile iron products can
be made.
V-Belt Sheaves
- Nonstandard diameter requirements.
- Nonstandard number of grooves.
- Unusual hub configurations.
- Deep grooves.
- Metric grooves.
- Added inertia or flywheel effect.
Synchronous Sprockets
- Nonstandard number of teeth.
- Nonstandard face widths.
- Unusual hub configurations.
- Special tooth profiles.
- Added inertia of flywheel effect.
Flat Belt Pulleys
- Nonstandard diameter requirements.
- Nonstandard face widths.
- Unusual hub configurations.
- Split through rim or arm designs.
- All types of special crowns.
- Added inertia or flywheel effect.
- Taper cone arrangements.
Balance
• The standard balance is a one-plane tolerance to a G26 quality
grade based on 3,500 RPM or the maximum rated speed. A twoplane balance to a G6.3 quality grade is available at an added
cost. Sure-Grip bushed products which are one-plane balanced
are marked so the bushing can be reinstalled at the application
the same way it was installed for balancing. See MPTA SPB-95
for standard balancing practices.
Standards
Flywheels
- Flywheels per customer design.
B ushing
• The following products meet or exceed the noted ANSI/RMA
design standards.
Classical V-Belt Sheaves
IP-20-2007
Narrow V-Belt Sheaves
IP-22-2007
Synchronous Belt Pulleys
IP-24-2001
Curvlinear Boil Sprockets
IP-27-2009
FHP Belts and Sheaves IP-23-2009
Hex Belts and Sheaves IP-21-2009
H ardware
V-Belt Sheaves, Synchronous Belt Sprockets,
F l a t B e l t P u l l e y s , e tc .
*Trademark of TB Wood’s Incorporated.
95
P O W E R
T R A N S M I S S I O N
P R O D U C T S B ushing
H ardware
Taper-Lock Bushings
Part No.
SAP No.
Wt.
Part No.
SAP No.
Wt.
Part No.
SAP No.
Wt.
TL1008
TL1108
TL1210
TL1215
TL1310
20181861
20181862
20181863
20181864
20181865
0.20
0.20
0.55
0.70
0.70
TL1610
TL1615
TL2012
TL2517
TL2525
20181866
20181867
20181868
20181869
20181870
0.70
0.80
1.40
2.50
3.50
TL3020
TL3535
TL4040
TL4545
20181871
20181872
20181873
20181874
5.00
10.00
17.00
25.00
S u r e - G r ip
Part No.
B ushing
H ardware
QT-7/16 MPB
QT-1/2
QT-9/16
QT-5/8
QT-11/16
QT-3/4
QT-13/16
QT-7/8
QT-15/16
QT-1
QT-1 1/16
QT-1 1/8
QT-1 3/16
QT-1 1/4
QT-1 5/16
QT-1 3/8
QT-1 7/16
QT-1 1/2
JA-1/2
JA-1/2
JA-9/16
JA-5/8
JA-11/16
JA-3/4
JA-13/16
JA-7/8
JA-15/16
JA-1
JA-1 1/16
JA-1 1/8
JA-1 3/16
JA-1 1/4
SH-7/16 MPB
SH-1/2
SH-9/16
SH-5/8
SH-11/16
SH-3/4
SH-13/16
SH-7/8
SAP No.
Wt.
Part No.
20181485
20181479
20181487
20181484
20181480
20181483
20181481
20181486
20181482
20181470
20181471
20181474
20181475
20181473
20181477
20181476
20181478
20181472
20181291
20181291
20181299
20181297
20181293
20181296
20181294
20181298
20181295
20181286
20181287
20181289
20181290
20181288
20181730
20181724
20181732
20181729
20181725
20181728
20181726
20181731
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.1
1.1
1.1
1.1
1.0
1.0
1.0
1.0
SH-15/16
SH-1
SH-1 1/16
SH-1 1/8
SH-1 3/16
SH-1 1/4
SH-1 5/16
SH-1 3/8
SH-1 7/16
SH-1 1/2
SH-1 9/16
SH-1 5/8
SH-1 11/16
SDS-7/16 MPB
SDS-1/2
SDS-9/16
SDS-5/8
SDS-11/16
SDS-3/4
SDS-13/16
SDS-7/8
SDS-15/16
SDS-1
SDS-1 1/16
SDS-1 1/8
SDS-1 3/16
SDS-1 1/4
SDS-1 5/16
SDS-1 3/8
SDS-1 3/8 3/8 KS
SDS-1 7/16
SDS-1 1/2
SDS-1 9/16
SDS-1 5/8
SDS-1 11/16
SDS-1 3/4
SDS-1 13/16
SDS-1 7/8
SDS-1 15/16
SDS-2
*Trademark of TB Wood’s Incorporated.
96
®*
Bushings
SAP No.
Wt.
Part No.
SAP No.
Wt.
20181727
20181712
20181713
20181716
20181718
20181715
20181720
20181719
20181722
20181714
20181723
20181721
20181717
20181583
20181576
20181585
20181582
20181577
20181581
20181578
20181584
20181579
20181559
20181560
20181563
20181567
20181562
20181571
20181569
20181570
20181573
20181561
20181575
20181572
20181564
20181568
20181565
20181574
20181566
20181580
1.0
0.9
0.9
0.9
0.8
0.8
0.7
0.7
0.7
0.6
0.6
0.5
0.5
1.7
1.7
1.7
1.6
1.6
1.6
1.6
1.5
1.5
1.5
1.4
1.4
1.4
1.3
1.3
1.2
1.2
1.2
1.1
1.1
1.0
1.0
1.0
0.9
0.9
0.8
0.7
SD-7/16 MPB
SD-1/2
SD-9/16
SD-5/8
SD-11/16
SD-3/4
SD-13/16
SD-7/8
SD-15/16
SD-1
SD-1 1/16
SD-1 1/8
SD-1 3/16
SD-1 1/4
SD-1 5/16
SD-1 3/8
SD-1 3/8 3/8 KS
SD-1 7/16
SD-1 1/2
SD-1 9/16
SD-1 5/8
SD-1 11/16
SD-1 3/4
SD-1 13/16
SD-1 7/8
SD-1 15/16
SD-2
SK-7/16 MPB
SK-1/2
SK-9/16
SK-5/8
SK-11/16
SK-3/4
SK-13/16
SK-7/8
SK-15/16
SK-1
SK-1 1/16
SK-1 1/8
SK-1 3/16
20181543
20181536
20181545
20181542
20181537
20181541
20181538
20181544
20181539
20181519
20181520
20181523
20181527
20181522
20181531
20181529
20181530
20181533
20181521
20181535
20181532
20181524
20181528
20181525
20181534
20181526
20181540
20181790
20181772
20181792
20181789
20181773
20181788
20181774
20181791
20181775
20181753
20181754
20181757
20181761
2.1
2.1
2.1
2.1
2.0
2.0
2.0
1.9
1.9
1.8
1.8
1.7
1.7
1.6
1.6
1.5
1.5
1.4
1.4
1.3
1.2
1.2
1.1
1.1
1.0
0.9
0.8
3.6
3.6
3.6
3.6
3.5
3.5
3.5
3.4
3.4
3.3
3.3
3.2
3.2
continued on page 97
S u r e - G r ip
Part No.
SK-1 1/4
SK-1 5/16
SK-1 5/16 3/8 KS
SK-1 3/8
SK-1 3/8 3/8 KS
SK-1 7/16
SK-1 1/2
SK-1 9/16
SK-1 5/8
SK-1 11/16
SK-1 3/4
SK-1 3/4 1/2 KS
SK-1 13/16
SK-1 7/8
SK-1 15/16
SK-2
SK-2 1/16
SK-2 1/8
SK-2 3/16
SK-2 1/4
SK-2 1/4 5/8 KW
SK-2 5/16
SK-2 3/8
SK-2 7/16
SK-2 1/2
SK-2 9/16 NO KW
SK-2 5/8 NO KW
SF-1/2 MPB
SF-1/2
SF-5/8
SF-3/4
SF-7/8
SF-15/16
SF-1
SF-1 1/16
SF-1 1/8
SF-1 3/16
SF-1 1/4
SF-1 5/16
SF-1 3/8
SF-1 3/8 3/8 KS
SF-1 7/16
SF-1 1/2
SF-1 9/16
SF-1 5/8
SF-1 11/16
SF-1 3/4
SF-1 13/16
SF-1 7/8
SF-1 5/16
SF-2
SF-2 1/16
SAP No.
Wt.
Part No.
20181756
20181766
20181767
20181764
20181765
20181769
20181755
20181771
20181768
20181758
20181762
20181763
20181759
20181770
20181760
20181776
20181777
20181781
20181782
20181779
20181780
20181784
20181783
20181786
20181778
20181787
20181785
20181636
20181635
20181655
20181654
20181656
20181637
20181618
20181619
20181622
20181626
20181621
20181630
20181628
20181629
20181632
20181620
20181634
20181631
20181623
20181627
20181624
20181633
20181630
20181638
20181639
3.1
3.1
3.1
3.0
3.0
2.9
2.9
2.8
2.7
2.6
2.5
2.5
2.4
2.4
2.3
2.2
2.1
2.0
2.0
1.9
1.9
1.8
1.7
1.6
1.5
1.3
1.1
5.1
5.1
5.0
5.0
4.9
4.8
4.8
4.7
4.7
4.6
4.5
4.5
4.4
4.4
4.3
4.2
4.2
4.1
4.0
3.9
3.8
3.7
3.6
3.5
3.4
SF-2 1/8
SF-2 3/16 DI
SF-2 1/4 DI
SF-2 1/4 5/8 KS D
SF-2 5/16 DI
SF-2 3/8 DI
SF-2 7/16 DI
SF-2 1/2 DI
SF-2 9/16 DI
SF-2 5/8 DI
SF-2 11/16 DI
SF-2 3/4 DI
SF-2 7/8 DI
SF-2 15/16 DI
E-7/8PB
E-7/8
E-15/16
E-1
E-1 1/8
E-1 3/16
E-1 1/4
E-1 5/16
E-1 3/8
E-1 3/8 3/8 KS
E-1 7/16
E-1 1/2
E-1 9/16
E-1 5/8
E-1 11/16
E-1 3/4
E-1 13/16
E-1 7/8
E-1 15/16
E-2
E-2 1/16
E-2 1/8
E-2 3/16
E-2 1/4
E-2 1/4 5/8 KS
E-2 5/16
E-2 3/8
E-2 7/16
E-2 1/2
E-2 9/16
E-2 5/8
E-2 11/16 DI
E-2 3/4 DI
E-2 13/16 DI
E-2 7/8 DI
E-2 15/16 DI
E-3 DI
E-3 1/8 DI
*Trademark of TB Wood’s Incorporated.
B ushing
P R O D U C T S ®*
H ardware
2 0 1 0
Bushings
SAP No.
Wt.
20181643
20181646
20181642
20181641
20181649
20181648
20181651
20181640
20181653
20181650
20181644
20181647
20181652
20181645
20181089
20181088
20181062
20181046
20181049
20181053
20181048
20181057
20181055
20181056
20181059
20181047
20181061
20181058
20181050
20181054
20181051
20181060
20181052
20181063
20181064
20181068
20181072
20181066
20181067
20181075
20181074
20181077
20181065
20181079
20181076
20181069
20181073
20181070
20181078
20181071
20181087
20181082
3.3
3.2
3.1
3.1
3.1
3.0
2.9
2.8
2.6
2.5
2.4
2.2
1.8
1.7
10.8
10.8
10.8
10.7
10.6
10.5
10.4
10.3
10.2
10.2
10.1
10.0
9.9
9.8
9.7
9.6
9.4
9.3
9.2
9.0
8.9
8.8
8.6
8.5
8.5
8.3
8.1
8.0
7.8
7.6
7.5
7.3
7.1
7.2
7.1
6.9
6.7
6.3
Part No.
SAP No.
Wt.
E-3 3/16 DI
E-3 1/4 DI
E-3 5/16 DI
E-3 3/8 DI
E-3 7/16 DI
E-3 1/2 DI
F-1
F-1
F-1 1/8
F-1 3/16
F-1 1/4
F-1 3/8
F-1 7/16
F-1 1/2
F-1 9/16
F-1 5/8
F-1 11/16
F-1 3/4
F-1 7/8
F-1 15/16
F-2
F-2 1/16
F-2 1/8
F-2 3/16
F-2 1/4
F-2 1/4 5/8 KS
F-2 5/16
F-2 3/8
F-2 7/16
F-2 1/2
F-2 9/16
F-2 5/8
F-2 11/16
F-2 3/4
F-2 13/16
F-2 7/8
F-2 15/16
F-3
F-3 1/8
F-3 3/16 DI
F-3 1/4 DI
F-3 5/16 DI
F-3 3/8 DI
F-3 7/16 DI
F-3 1/2 DI
F-3 5/8 DI
F-3 11/16 DI
F-3 3/4 DI
F-3 7/8 DI
F-3 15/16 DI
F-4 NO KW DI
20181083
20181081
20181085
20181084
20181086
20181080
20181147
20181147
20181150
20181153
20181149
20181155
20181157
20181148
20181159
20181156
20181151
20181154
20181158
20181152
20181161
20181162
20181166
20181170
20181164
20181165
20181173
20181172
20181175
20181163
20181177
20181174
20181167
20181171
20181168
20181176
20181169
20181178
20181181
20181184
20181180
20181187
20181186
20181189
20181179
20181188
20181182
20181185
20181190
20181183
20181191
6.0
5.8
5.7
5.5
5.2
4.7
17.9
17.9
17.7
17.6
17.5
17.2
17.1
16.9
16.8
16.7
16.5
16.3
16.0
15.8
15.6
15.4
15.2
15.0
14.8
14.8
14.5
14.3
14.1
13.9
13.7
13.4
13.2
12.9
12.6
12.3
12.1
11.8
11.2
10.9
10.6
11.0
10.6
10.3
10.0
9.4
9.0
8.7
8.1
7.7
6.9
H ardware
T R A N S M I S S I O N
B ushing
P O W E R
continued on page 98
97
P O W E R
T R A N S M I S S I O N
P R O D U C T S S u r e - G r ip
Part No.
B ushing
H ardware
J-1 7/16 MPB
J-1 7/16
J-1 1/2
J-1 11/16
J-1 3/4
J-1 7/8
J-1 15/16
J-2
J-2 1/8
J-2 3/16
J-2 1/4
J-2 1/4-5/8KS
J-2 5/16
J-2 3/8
J-2 7/16
J-2 1/2
J-2 5/8
J-2 11/16
J-2 3/4
J-2 7/8
J-2 15/16
J-3
J-3 1/8
J-3 3/16
J-3 1/4
J-3 5/16
J-3 3/8
J-3 7/16
J-3 1/2
J-3 5/8
J-3 11/16 DI
J-3 3/4 DI
J-3 13/16 DI
J-3 7/8 DI
J-3 15/16 DI
J-4 DI
J-4 1/8 DI
J-4 3/16 DI
J-4 1/4 DI
J-4 3/8 DI
J-4 7/16 DI
J-4 1/2 DI
M-1 15/16 MPB
M-1 15/16
M-2
M-2 3/16
M-2 1/4
M-2 3/8
M-2 7/16
M-2 1/2
M-2 5/8
M-2 11/16
H ardware
Bushings
SAP No.
Wt.
Part No.
SAP No.
Wt.
20181250
20181249
20181245
20181246
20181248
20181251
20181247
20181252
20181255
20181258
20181254
20332967
20181261
20181260
20181263
20181253
20181262
20181256
20181259
20181264
20181257
20181265
20181268
20181272
20181267
20181275
20181274
20181277
20181266
20181276
20181269
20181273
20181270
20181278
20181271
20181285
20181281
20181282
20181280
20181283
20181284
20181279
20181336
20181335
20181337
20181342
20181339
20181344
20181347
20181338
20181346
20181340
28.1
28.1
28.0
27.4
27.2
26.7
26.5
26.3
25.8
25.6
25.3
25.3
25.0
24.7
24.5
24.2
23.6
23.3
23.0
22.2
21.9
21.6
20.9
20.5
20.1
19.6
19.3
18.9
18.5
17.7
17.2
16.8
17.4
17.0
16.5
16.1
15.2
14.7
14.2
13.2
12.7
12.2
63.7
63.7
63.3
62.3
61.9
61.0
60.6
60.1
59.3
58.8
M-2 3/4
M-2 7/8
M-2 15/16
M-3
M-3 1/8
M-3 3/16
M-3 1/4
M-3 3/8
M-3 7/16
M-3 1/2
M-3 5/8
M-3 11/16
M-3 3/4
M-3 1316
M-3 7/8
M-3 15/16
M-4
M-4 1/8
M-4 3/16
M-4 1/4
M-4 3/8
M-4 7/16
M-4 1/2
M-4 5/8
M-4 11/16
M-4 3/4
M-4 7/8
M-4 15/16
M-5
M-5 3/16
M-5 1/4
M-5 3/8
M-5 7/16
M-5 1/2
N-2 15/16
N-3
N-3 3/8
N-3 7/16
N-3 1/2
N-3 5/8
N-3 3/4
N-3 7/8
N-3 15/16
N-4
N-4 3/16
N-4 1/4
N-4 3/8
N-4 7/16
N-4 1/2
N-4 5/8
N-4 3/4
N-4 7/8
20181343
20181348
20181341
20181349
20181352
20181356
20181351
20181358
20181360
20181350
20181359
20181353
20181357
20181354
20181361
20181355
20181362
20181365
20181368
20181364
20181370
20181372
20181363
20181371
20181366
20181369
20181373
20181367
20181374
20181377
20181376
20181378
20181379
20181375
20181393
20181394
20181398
20181400
20181395
20181399
20181397
20181401
20181396
20181402
20181406
20181404
20181408
20181410
20181403
20181409
20181407
20181411
58.3
57.2
56.7
56.2
55.2
54.6
54.1
52.8
52.2
51.6
50.4
49.7
49.1
48.4
47.6
46.9
46.2
44.8
44.1
43.4
41.9
41.2
40.4
38.5
37.5
36.7
37.8
37.0
36.1
33.5
32.6
31.0
29.9
28.9
84.1
83.5
79.3
78.6
77.9
76.4
74.9
73.1
72.3
71.5
68.9
68.1
66.3
65.4
64.5
62.0
60.0
58.1
*Trademark of TB Wood’s Incorporated.
98
®*
B ushing
Part No.
SAP No.
Wt.
N-4 15/16
N-5
N-5 3/16
N-5 7/16
N-5 1/2
N-5 7/8
N-5 15/16
P-2 15/16
P-3 1/4
P-3 7/16
P-3 1/2
P-3 5/8
P-3 3/4
P-3 7/8
P-3 15/16
P-4
P-4 1/4
P-4 3/8
P-4 7/16
P-4 1/2
P-4 5/8
P-4 11/16
P-4 3/4
P-4 7/8
P-4 15/16
P-5
P-5 3/16
P-5 1/4
P-5 5/16
P-5 3/8
P-5 7/16
P-5 1/2
P-5 3/4
P-5 7/8
P-5 15/16
P-6
P-6 1/16
P-6 1/4
P-6 7/16
P-6 1/2
P-6 3/4
P-7
W-4 1/4 MPB
W-4 7/8 MPB
W-5 1/4 MPB
W-5 7/8 MPB
W-6 1/2 MPB
W-7 1/4 MPB
S-6 MPB
S-8 MPB
S-9 MPB
20181405
20181412
20181415
20181416
20181413
20181417
20181414
20181425
20181427
20181431
20181426
20181430
20181429
20181432
20181428
20181433
20181435
20181439
20181441
20181434
20181440
20181436
20181438
20181442
20181437
20181443
20181447
20181445
20181450
20181449
20181451
20181444
20181448
20181452
20181446
20181453
20181454
20181456
20181458
20181455
20181457
20181459
20181843
20181844
20181845
20181846
20181847
20181848
20181516
20181517
20181518
57.0
56.0
56.1
51.7
50.6
44.3
43.9
141.2
137.6
134.9
134.1
132.4
130.6
128.5
127.6
126.7
122.7
120.7
119.6
118.6
115.7
114.6
113.5
111.2
110.0
108.8
105.2
103.9
102.7
101.4
100.1
98.8
98.1
95.3
93.9
92.5
91.0
86.5
82.0
80.5
74.7
68.1
249.0
235.0
227.0
210.0
193.0
169.0
471.0
381.0
326.0
P O W E R
T R A N S M I S S I O N
B ushing
P R O D U C T S S u r e - G r ip
®*
H ardware
2 0 1 0
Bushings
(Millimeter Bores-Inch Bolts)
*Trademark of TB Wood’s Incorporated.
Wt.
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.8
0.8
0.7
1.5
1.5
1.4
1.4
1.3
1.2
1.1
1.1
1.0
1.8
1.8
Part No.
SDX28MM
SDX30MM
SDX32MM
SDX35MM
SDX38MM
SDX40MM
SDX42MM
SKX24MM
SKX25MM
SKX28MM
SKX30MM
SKX32MM
SKX35MM
SKX38MM
SKX40MM
SKX42MM
SKX45MM
SKX48MM
SKX50MM
SKX55MM
SFX28MM
SFX30MM
SFX32MM
SFX35MM
SFX38MM
SFX40MM
SFX42MM
SFX45MM
SFX48MM
SFX50MM
SFX55MM
SFX60MM DI
SFX65MM DI
EX35MM
EX38MM
EX40MM
EX42MM
EX45MM
SAP No.
20181611
20181612
20181613
20181614
20181615
20181616
20181617
20181830
20181831
20181832
20181833
20181834
20181835
20181836
20181837
20181838
20181839
20181840
20181841
20181842
20181699
20181700
20181701
20181702
20181703
20181704
20181705
20181706
20181707
20181708
20181709
20181710
20181711
20181134
20181135
20181136
20181137
20181138
Wt.
Part No.
1.7
1.7
1.6
1.5
1.4
1.3
1.2
3.3
3.3
3.2
3.2
3.1
3.0
2.9
3.6
2.7
2.6
2.4
2.3
2.0
4.7
4.6
4.5
4.4
4.2
4.2
4.1
3.9
3.7
3.6
3.2
3.0
2.8
10.2
10.0
9.9
9.8
9.6
EX48MM
EX50MM
EX55MM
EX60MM
EX65MM
EX70MM
EX75MM DI
EX80MM DI
FX45MM
FX48MM
FX50MM
FX55MM
FX60MM
FX65MM
FX70MM
FX75MM
FX80MM
FX85MM
FX90MM DI
JX50MM
JX55MM
JX60MM
JX65MM
JX70MM
JX75MM
JX80MM
JX85MM
JX90MM
JX95MM
JX100MM
MX80MM
MX90MM
MX100MM
MX120MM
N-100MM
N-120MM
PX150MM
SAP No.
20181139
20181140
20181141
20181142
20181143
20181144
20181145
20181146
20181234
20181235
20181236
20181237
20181238
20181239
20181240
20181241
20181242
20181243
20181244
20181325
20181326
20181327
20181328
20181329
20181330
20181331
20181332
20181333
20181334
20181324
20181389
20181390
20181387
20181388
20181391
20181392
20181469
Wt.
9.3
9.2
8.6
8.1
7.6
7.1
6.9
6.7
16.2
16.0
15.8
15.0
14.3
13.7
12.9
12.1
11.2
10.6
9.7
26.5
25.6
24.7
23.9
23.0
21.9
20.9
19.3
18.1
16.8
16.5
55.0
51.2
46.9
37.0
72.3
60.2
95.8
H ardware
SAP No.
20181502
20181503
20181504
20181505
20181506
20181507
20181508
20181509
20181510
20181511
20181512
20181513
20181514
20181515
20181310
20181311
20181312
20181313
20181314
20181315
20181316
20181747
20181748
20181749
20181750
20181751
20181752
20181600
20181601
20181602
20181603
20181604
20181605
20181606
20181607
20181608
20181609
20181610
B ushing
Part No.
QTX14MM
QTX15MM
QTX16MM
QTX18MM
QTX19MM
QTX20MM
QTX22MM
QTX24MM
QTX25MM
QTX28MM
QTX30MM
QTX32MM
QTX35MM
QTX38MM
JAX15MM
JAX16MM
JAX19MM
JAX20MM
JAX24MM
JAX25MM
JAX28MM
SHX24MM
SHX25MM
SHX28MM
SHX30MM
SHX32MM
SHX35MM
SDSX24MM
SDSX25MM
SDSX28MM
SDSX30MM
SDSX32MM
SDSX35MM
SDSX38MM
SDSX40MM
SDSX42MM
SDX24MM
SDX25MM
99
P O W E R
T R A N S M I S S I O N
P R O D U C T S B ushing
H ardware
“L” Series Flangeless Bushings
Part No.
SAP No.
Wt.
Part No.
SAP No.
Wt.
SKL-1/2
SKL-1/2
SKL-5/8
SKL-3/4
SKL-7/8
SKL-15/16
SKL-1
SKL-1 1/8
SKL-1 3/16
SKL-1 1/4
SKL-1 5/16
SKL-1 3/8
SKL-1 7/16
SKL-1 1/2
SKL-1 9/16
SKL-1 5/8
SKL-1 11/16
SKL-1 3/4
SKL-1 13/16
SKL-1 7/8
SKL-1 15/16
SFL-1/2
SFL-1/2
SFL-5/8
SFL-3/4
SFL-7/8
SFL-15/16
SFL-1
SFL-1 1/8
SFL-1 3/16
SFL-1 1/4
SFL-1 5/16
SFL-1 3/8
SFL-1 7/16
SFL-1 1/2
SFL-1 9/16
SFL-1 5/8
20181808
20181808
20181812
20181811
20181813
20181810
20181793
20181796
20181800
20181795
20181803
20181802
20181805
20181794
20181807
20181804
20181797
20181801
20181798
20181806
20181799
20181673
20181673
20181683
20181682
20181684
20181675
20181658
20181661
20181665
20181660
20181668
20181667
20181670
20181659
20181672
20181669
1.7
1.7
1.7
1.6
1.6
1.6
1.6
1.5
1.4
1.4
1.3
1.3
1.2
1.2
1.2
1.1
1.1
1.0
1.0
0.9
0.8
2.1
2.1
2.1
2.0
2.0
2.0
2.0
1.9
1.8
1.8
1.7
1.7
1.6
1.6
1.5
1.5
SFL-1 11/16
SFL-1 3/4
SFL-1 13/16
SFL-1 7/8
SFL-1 15/16
SFL-2
SFL-2 1/8
SFL-2 3/16
SFL-2 1/4
SFL-2 5/16
SFL-2 3/8
EL-78 MPB
EL-78
EL-15/16
EL-1
EL-1 1/8
EL-1 3/16
EL-1 1/4
EL-1 5/16
EL-1 3/8
EL-1 7/16
EL-1 1/2
EL-1 9/16
EL-1 5/8
EL-1 11/16
EL-1 3/4
EL-1 13/16
EL-1 7/8
EL-1 15/16
EL-2
EL-2 1/8
EL-2 3/16
EL-2 1/4
EL-2 5/16
EL-2 3/8
EL-2 7/16
EL-2 1/2
20181662
20181666
20181663
20181671
20181664
20181676
20181678
20181679
20181677
20181681
20181680
20181121
20181120
20181105
20181090
20181093
20181097
20181092
20181100
20181099
20181102
20181091
20181104
20181101
20181094
20181098
20181095
20181103
20181096
20181106
20181109
20181112
20181108
20181115
20181114
20181117
20181107
1.4
1.4
1.4
1.3
1.3
1.2
1.1
1.0
1.0
0.9
0.9
4.1
4.1
4.0
3.9
3.8
3.8
3.7
3.6
3.6
3.5
3.5
3.4
3.4
3.3
3.2
3.2
3.1
3.0
3.0
2.9
2.8
2.7
2.6
2.5
2.4
2.3
20181119
20181116
20181110
20181113
20181111
20181118
20181192
20181192
20181195
20181198
20181194
20181200
20181202
20181193
20181204
20181201
20181196
20181199
20181203
20181197
20181206
20181209
20181213
20181208
20181216
20181215
20181218
20181207
20181220
20181217
20181210
20181214
20181211
20181219
20181212
20181221
20181222
B ushing
H ardware
S u r e - G r ip I d l e r B u s h i n g s
& Replacement Bearings
®*
Part No.
SAP No.
Wt.
SH-BB
SD-BB
SK-BB
SF-BB
E-BB
20221732
20221733
20221734
20221735
20221736
1.5
2.5
4.5
8.0
12.0
*Trademark of TB Wood’s Incorporated.
100
EL-2 9/16
EL-2 5/8
EL-2 11/16
EL-2 3/4
EL-2 13/16
EL-2 7/8
FL-1
FL-1
FL-1 1/8
FL-1 3/16
FL-1 1/4
FL-1 3/8
FL-1 7/16
FL-1 1/2
FL-1 9/16
FL-1 5/8
FL-1 11/16
FL-1 3/4
FL-1 7/8
FL-1 15/16
FL-2
FL-2 1/8
FL-2 3/16
FL-2 1/4
FL-2 5/16
FL-2 3/8
FL-2 7/16
FL-2 1/2
FL-2 9/16
FL-2 5/8
FL-2 11/16
FL-2 3/4
FL-2 13/16
FL-2 7/8
FL-2 15/16
FL-3
FL-3 1/8
Use bearing G275
Use bearing G275
Use bearing G276
Use bearing G276
Use bearing G277
Part No.
SAP No.
Wt.
G275
G276
G277
20221737
20221738
20221739
1.0
1.0
0.8
2.3
2.2
2.1
2.0
1.9
1.8
8.5
8.5
8.3
8.2
8.1
8.0
7.9
7.8
7.6
7.5
7.4
7.3
7.1
7.0
6.7
6.6
6.5
6.4
6.3
6.2
6.1
5.9
5.7
5.6
5.4
5.3
5.1
4.9
4.8
4.6
4.5
P R O D U C T S B ushing
M e t r ic S u r e - G r ip
Part No.
SAP No.
Wt.
Part No.
QTMX10MM
QTMX10MM
QTMX11MM
QTMX14MM
QTMX15MM
QTMX16MM
QTM19MM
QTMX20MM
QTMX24MM
QTMX25MM
QTMX28MM
QTMX30MM
QTMX32MM
QTMX38MM
JAMX10MM
JAMX10MM
JAMX11MM
JAMX14MM
JAMX15MM
JAMX19MM
JAMX20MM
JAMX24MM
JAMX25MM
JAMX28MM
SHMX10MM
SHMX10MM
SHMX11MM
SHMX14MM
SHMX15MM
SHMX19MM
SHMX20MM
SHMX24MM
SHMX25MM
SHMX28MM
SHMX30MM
SHMX35MM
SHMX38MM
SHMX40MM
20181489
20181489
20181491
20181492
20181493
20181494
20181488
20181495
20181496
20181497
20181498
20181499
20181500
20181501
20181300
20181300
20181302
20181303
20181304
20181305
20181306
20181307
20181308
20181309
20181733
20181733
20181735
20181736
20181737
20181738
20181739
20181740
20181741
20181742
20181743
20181744
20181745
20181746
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.1
1.1
1.1
1.1
1.1
1.0
1.0
1.0
1.0
0.9
0.8
0.8
0.7
0.6
SDSMX10MM MPB 20181586
SDSMX15MM
20181587
SDSMX19MM
20181588
SDSMX20MM
20181589
SDSMX24MM
20181590
SDSMX25MM
20181591
SDSMX28MM
20181592
SDSMX30MM
20181593
SDSMX32MM
20181594
SDSMX35MM
20181595
SDSMX38MM
20181596
SDSMX40MM
20181597
SDSMX42MM
20181598
SDSMX48MM
20181599
SDMX15MM
20181546
SDMX15MM
20181546
SDMX19MM
20181548
SDMX20MM
20181549
SDMX24MM
20181550
SDMX28MM
20181552
SDMX30MM
20181553
SDMX35MM
20181554
SDMX38MM
20181555
SDMX40MM
20181556
SDMX42MM
20181557
20181558
SDMX48MM
SKMX15MM MPB 20181815
SKMX19MM
20181816
SKMX20MM
20181817
SKMX24MM
20181818
SKMX28MM
20181819
SKMX30MM
20181820
SKMX32MM
20181821
SKMX35MM
20181822
SKMX38MM
20181823
SKMX40MM
20181824
SKMX42MM
20181825
SKMX48MM
20181826
SAP No.
®*
H ardware
2 0 1 0
Bushings
Wt.
Part No.
SAP No.
Wt.
1.7
1.6
1.6
1.6
1.5
1.5
1.4
1.4
1.3
1.2
1.1
1.0
1.0
0.9
2.0
2.0
1.9
1.9
1.9
1.7
1.7
1.5
1.4
1.3
1.2
1.0
3.6
3.5
3.5
3.4
3.2
3.2
3.1
3.0
2.9
2.8
2.7
2.4
SKMX50MM
SKMX55MM
SKMX60MM
SFMX15MM MPB
SFMX20MM
SFMX24MM
SFMX28MM
SFMX30MM
SFMX35MM
SFMX38MM
SFMX40MM
SFMX42MM
SFMX48MM
SFMX50MM
SFMX55MM
SFMX60MM
EMX20MM MPB
EMX28MM
EMX30MM
EMX38MM
EMX40MM
EMX42MM
EMX48MM
EMX50MM
EMX55MM
EMX60MM
EMX70MM
FMX20MM MPB
FMX30MM MPB
FMX38MM MPB
FMX40MM MPB
FMX42MM MPB
FMX48MM MPB
FMX50MM MPB
FMX55MM MPB
FMX60MM MPB
FMX70MM MPB
20181827
20181828
20181829
20181686
20181687
20181688
20181689
20181690
20181691
20181692
20181693
20181694
20181695
20181696
20181697
20181698
20181123
20181124
20181125
20181126
20181127
20181128
20181129
20181130
20181131
20181132
20181133
20181224
20181225
20181226
20181227
20181228
20181229
20181230
20181231
20181232
20181233
2.3
2.0
1.7
5.1
5.0
4.8
4.7
4.6
4.0
4.2
4.2
4.1
3.7
3.5
3.2
3.0
10.8
10.6
10.5
10.0
9.9
9.8
9.3
9.2
8.6
8.1
7.1
18.0
17.6
16.9
16.8
16.7
18.0
15.7
15.0
14.3
12.9
H ardware
T R A N S M I S S I O N
*Trademark of TB Wood’s Incorporated.
M e t r ic “ L ” S e r i e s
Flangeless Bushings
Part No.
SAP No.
Wt.
Part No.
SAP No.
Wt.
SKLMX15MM MPB
SFLMX15MM MPB
20181814
20181685
1.7
2.1
ELMX20MM MPB
20181122
4.1
B ushing
P O W E R
101
P O W E R
T R A N S M I S S I O N
S u r e - G r ip
®*
B ushing
H ardware
Short Bushings
Part No.
SAP No.
Wt.
Part No.
JS-2 7/16
JS-2 15/16
JS-3 7/16
JS-3 1/2
JS-3 15/16
JS-4 7/16
MS-3 7/16
MS-3 1/2
MS-3 15/16
MS-4 7/16
MS-4 15/16
MS-5 7/16
MS-5 1/2
20181318
20181317
20181322
20181320
20181321
20181323
20181382
20181380
20181381
20181385
20181384
20181386
20332977
20.0
18.1
15.9
15.6
14.3
11.5
41.2
40.7
37.3
33.3
30.9
25.9
25.9
NS-3 15/16
NS-4 7/16
NS-4 15/16
NS-5 7/16
NS-5 1/2
NS-5 15/16
NS-6
PS-4 15/16
PS-5 7/16
PS-5 15/16
PS-6
PS-6 7/16
PS-6 1/2
PS-6 15/16
PS-7
*Trademark of TB Wood’s Incorporated.
B ushing
H ardware
102
P R O D U C T S SAP No.
Wt.
Part No.
SAP No.
Wt.
20181419
20181421
20181420
20181423
20332968
20181422
20181424
20181460
20181463
20181462
20181464
20181467
20181465
20181466
20181468
66.3
52.5
46.5
43.9
43.1
39.0
38.8
88.3
81.3
78.4
77.4
70.0
69.0
61.3
60.4
WS-5 7/16
WS-5 15/16
WS-6
WS-6 7/16
WS-6 1/2
WS-6 15/16
WS-7
WS-7 1/2
WS-7 15/16
WS-8
WS-8 7/16
WS-8 1/2
20181850
20181849
20181851
20181854
20181852
20181853
20181855
20181856
20181857
20181858
20181860
20181859
172.3
161.1
160.0
155.0
153.0
140.0
139.0
137.0
126.9
124.0
107.3
105.0
P O W E R
T R A N S M I S S I O N
S P E C I A L T Y
P R O D U C T S Neothane
2 0 1 0
®
A pp l i c a t i o n s
Specialty belt for specific types of machines and
equipment.
• Machine Tools
• Appliances
• Computer Industry
• Blowers
•Woodworking Machines
• Medical Industry
Key Features & Benefits
A D i f f e r e n t A pp r o a c h
to
V-Belts
Neothane V-belts can provide a different approach to V-belt
power transmission for appliances and light-duty machinery.
The features of the belt will make it possible to gain competitive
advantages in many areas of application.
S m oo t h O p e r a t o r
Smaller sheave diameters, higher speed ratios, shorter center
distances, and higher speeds in belt power transmission
applications are possible. Elimination of double reduction drives,
made possible by the higher speed ratios permitted, result
in decreased space requirements for many applications. The
precision characteristics of this belt give a smoothness of operation
that reduces noise to a minimum in the appurtenances of a drive.
The Low-Maintenance
V-Belt Alternative
This belt is ideal for machines with long warranty periods. The
outstanding characteristics make it virtually maintenance-free and
therefore reduce service costs. Greater horsepower can be utilized
by the designer with reasonable belt life. Or, for a given amount of
power to be transmitted, belt life can be greater than ever before.
S P E C I A L T Y
Part No: 5M 710
5M
5mm ( 3 ⁄16˝) Top Width
710
710mm (27.95˝) Outside Length
• Ribbed top for transverse rigidity, flexibility, and
cool running conditions.
•Narrow top width for use on narrow, small
diameter sheaves and exceptional flexibility on
short centers.
•Cords are resistant to elongation or shrinkage,
provide great strength and long flex life.
•Polyurethane compounding for firmer grip,
greater strength, and high resistance to oil, heat,
abrasion, ozone, and fatigue.
•Smooth machined sides for quiet running,
vibration-free operation, and uniform grip.
•Sixty-degree angle cross section for uniform
support that keeps the load carrying cord in the same plane pulling together.
3M
5M
0.18
0.125"
0.094"
3 m N o m i n a l T o p W i d t h 1⁄ 8 ˝
Part Number Eff. Length (in)
*3M180
7.09
*3M185
7.28
*3M190
7.48
*3M195
7.68
*3M200
7.87
*3M206
8.11
*3M212
8.35
*3M218
8.58
*3M224
8.82
*3M230
9.06
*3M236
9.29
Part Number Eff. Length (in)
*3M243
9.57
*3M250
9.84
*3M258
10.16
*3M265
10.43
*3M272
10.71
*3M280
11.02
*3M290
11.42
*3M300
11.81
*3M307
12.09
*3M315
12.40
*3M325
12.80
Part Number Eff. Length (in)
*3M335
13.19
*3M345
13.58
*3M355
13.98
*3M365
14.37
*3M375
14.76
*3M387
15.24
*3M400
15.75
*3M412
16.22
*3M425
16.73
*3M437
17.20
*3M450
17.72
Part Number Eff. Length (in)
*3M462
18.19
*3M475
18.70
*3M487
19.17
*3M500
19.69
*3M515
20.28
*3M530
20.87
*3M545
21.46
*3M560
22.05
*3M580
22.83
*3M600
23.62
*3M615
24.21
Part Number Eff. Length (in)
7M
*3M630 0.313"
24.80
*3M650
25.59
*3M670
26.38
*3M690
27.17
*3M710
27.95
0.219"
*3M730
28.74
*3M750
29.53
0.125"
11
0.
0.281"
*Nonstock: Please check factory for availability.
Contact your local Goodyear Engineered Products PTP industrial distributor
or go to www.goodyearep.com/ptp to locate one.
103
P O W E R
T R A N S M I S S I O N
S P E C I A L T Y
P R O D U C T S Neothane
®
3M
5M
0.188"
0.125"
0.094"
0.125"
5 m N o m i n a l T o p W i d t h 3⁄ 16 ˝
Part Number Eff. Length (in)
5M280
11.02
5M290
11.42
5M300
11.81
5M307
12.09
5M315
12.40
5M325
12.80
5M335
13.19
5M345
13.58
5M355
13.98
5M365
14.37
14.76
5M375
5M387
15.24
5M400
15.75
Part Number Eff. Length (in)
5M412
16.22
5M425
16.73
17.2
5M437
5M450
17.72
5M462
18.19
5M475
18.70
19.17
5M487
5M500
19.69
5M515
20.28
5M530
20.87
5M545
21.46
5M560
22.05
5M580
22.83
Part Number Eff. Length (in)
5M600
23.62
5M615
24.21
5M630
24.80
5M650
25.59
5M670
26.38
27.17
5M690
5M710
27.95
5M730
28.74
5M750
29.53
5M775
30.51
5M800
31.50
5M825
32.48
5M850
33.46
7M (in)
Part Number Eff. Length
0.313"
5M875
34.45
5M900
35.43
5M925
36.42
5M950
37.40
0.219"
38.39
5M975
5M1000
39.37
5M1030
40.55
5M1060
41.73
*5M1090 42.91
5M1120
44.09
5M1150
45.28
5M1180
46.46
5M1220
48.03
Part Number Eff.11M
Length (in)
*5M1250 0.438"
49.21
*5M1280 50.39
*5M1320 51.97
*5M1360 53.54
*5M1400
55.12
0.281"
*5M1450 57.09
*5M1500 59.06
*5M1600 62.99
3M
*5M1650 0.125"
64.96
*5M1850 72.83
0.094"
5M
0.188"
0.125"
7M
0.313"
0.219"
0.281"
7 m N o m i n a l T o p W i d t h 5⁄ 16 ˝
S P E C I A L T Y
Part Number Eff. Length (in)
7M500
19.69
*7M515
20.28
7M530
20.87
*7M545
21.46
7M560
22.05
7M580
22.83
7M600
23.62
7M615
24.21
7M630
24.80
7M650
25.59
7M670
26.38
Part Number Eff. Length (in)
7M690
27.17
7M710
27.95
7M730
28.74
7M750
29.53
7M775
30.51
7M800
31.50
7M825
32.48
7M850
33.46
7M875
34.45
7M900
35.43
7M925
36.42
Part Number Eff. Length (in)
7M950
37.40
7M975
38.39
7M1000
39.37
7M1030
40.55
7M1060
41.73
7M1090
42.91
7M1120
44.09
7M1150
45.28
7M1180
46.46
7M1220
48.03
7M1250
49.21
Part Number Eff. Length (in)
7M1280
50.39
7M1320
51.97
7M1360
53.54
7M1400
55.12
7M1450
57.09
7M1500
59.06
3M
7M1550
61.02
0.125"
7M1600
62.99
7M1650 0.094"
64.96
7M1700
66.93
7M1750
68.90
Part Number Eff. Length (in)
7M1800
70.87
7M1850
72.83
7M1900
74.80
7M1950
76.77
7M2000
78.74
*7M20605M 81.10
7M21200.188"83.46
7M2180
85.83
*7M2240
88.19
*7M2300
90.55
0.125"
7M
0.313"
11M
0.438"
0.219"
0.281"
1 1 m N o m i n a l T o p W i d t h 7⁄ 16 ˝
Part Number Eff. Length (in)
11M710
27.95
*11M730 28.74
*11M750 29.53
*11M775 30.51
11M800
31.50
11M825
32.48
11M850
33.46
11M875
34.45
11M900
35.43
Part Number Eff. Length (in)
11M925
36.42
11M950
37.40
11M975
38.39
11M1000 39.37
11M1030 40.55
11M1060 41.73
*11M1090 42.91
11M1120 44.09
11M1150 45.28
Part Number Eff. Length (in)
11M1180 46.46
11M1220 48.03
11M1250 49.21
11M1280 50.39
11M1320 51.97
11M1360 53.54
11M1400 55.12
11M1450 57.09
11M1500 59.06
*Nonstock: Please check factory for availability.
Note: Rubber equivalents for 5M, 7M, and 11M sizes are available in mandrel minimums.
104
Part Number Eff. Length (in)
11M1550 61.02
11M1600 62.99
11M1650 64.96
11M1700 66.93
*11M1750 68.90
11M1800 70.87
*11M1850 72.83
11M1900 74.80
11M1950 76.77
11M
0.438"
Part Number Eff. Length (in)
11M2000 78.74
11M2060 81.10
11M2120 83.46
11M2180 85.83
11M2240 88.19
11M2300 90.55
P O W E R
T R A N S M I S S I O N
P R O D U C T S S P E C I A L T Y
2 0 1 0
Variable Speed
A pp l i c a t i o n s
For use on variable speed sheave drives requiring exact
speed control and maximum range of speed changes.
Ideal for recreational equipment, agricultural
applications, and machine tools.
• Exercise Equipment
• Automobiles
• Medical Equipment
• Power Equipment
• Farm Equipment
• Machine Tools
T op P e r f o r m a n c e
at
Every Speed
Goodyear Engineered Products Variable Speed belts deliver the
speed and horsepower the drives on your equipment were designed
to achieve. Excellent transverse rigidity and exceptional flexibility
prevent buckling at minimum diameter settings where belt stresses
are greatest. Firm gripping action in the contact area provides
positive traction for precise, immediate response. Together, they
assure reliable, predictable transmission of maximum power over
the drive’s full operating range.
And top performance also means that you get longer life
from Goodyear Engineered Products Variable Speed belts.
That translates to less downtime for belt maintenance and
more productivity from your equipment, which leads to greater
operating economy by any measure.
U n i f o r m C r oss S e c t i o n
M e a n s L e ss D r i v e W e a r
The precision forming that goes into every one of our Variable
Speed belt assures a completely uniform cross section. This
allows even tracking and smooth running without any vibration
problems. As a result, the life of the belt—as well as bearings,
sheaves, and other drive components—is significantly extended.
Longer wear is a great way to save money and increase productivity.
Key Features & Benefits
•Durable variable speed profile.
•Super strong Flexten® tensile members.
• Fiber-reinforced, latest compounded technology
compression section.
•High-horsepower capacity.
•Milled edge construction for superior dimensional stability.
•Oil, heat, ozone, and abrasion resistant.
•Static conductive.*
Exceptional Lengthwise Flexibility
Allows for Small Pulleys
We build these belts thin with precise, uniform cogs on the
underside for maximum lengthwise flexibility. They can be used
on small pulley drives without any sacrifice of gripping action or
cross rigidity. Cogging also minimizes bottom cracking, a major
cause of premature failure.
True Dimensional Stability
& H i g h e r H o r s e po w e r C a p a b i l i t y
for Long Belt Life
S P E C I A L T Y
Part No: 3226V585
3⁄4˝ Top Width
32
26
Angle of Sheave Groove
V
Variable Speed Profile - With Flexten® Tensile Member
585
58.5˝ Pitch Length
Cut-Edge, Molded Cog Construction Shown
Our Flexten tension cords get their muscle from a special
tempering for maximum strength and resilience. This gives
Goodyear Engineered Products Variable Speed belts the
dimensional stability they need to carry more horsepower and to
experience less elongation over the life of the belt. In short,
these Variable Speed belts provide you with longer life on the
toughest drives.
*Drive conditions and service variables in combination with time in operation can result in a loss of static conductivity. It is recommended that a conductivity check
be added to drive preventive maintenance programs where belt static conductivity is a requirement.
To learn more visit www.goodyearep.com/ptp.
105
P O W E R
T R A N S M I S S I O N
P R O D U C T S S P E C I A L T Y
Variable Speed
C u t - E d g e C o n s t r u cti o n
Variable Speed Stock Part Numbers
1228V255
1422V235
1422V240
1422V270
1422V290
1422V300
1422V330
1422V340
1422V360
1422V400
1422V420
1422V440
1422V460
1422V466
1422V470
1422V480
1422V540
1422V600
1422V660
1422V720
1422V780
S P E C I A L T Y
1430V215
1430V315
1430V450
1430V500
1622V270
1622V336
1626V262
1626V290
1626V293
1626V304
1626V330
1626V339
1626V380
1626V384
1626V395
1626V411
1626V428
1626V440
1626V455
1626V513
1626V517
1626V597
1626V604
1626V658
1626V700
1628V210
1628V315
1632V210
1822V328
1828V368
1922V256
1922V277
1922V282
1922V298
1922V302
1922V321
1922V332
1922V338
1922V363
1922V381
1922V386
1922V403
1922V417
1922V426
1922V443
1922V454
1922V460
1922V484
1922V526
1922V544
1922V604
1922V630
1922V646
1922V666
1922V686
1922V706
1922V721
1922V726
1922V751
1922V756
1922V806
1922V846
1922V891
1922V966
1922V1146
1926V250
1926V275
1926V407
1926V427
1930V366
1930V400
1930V425
1930V431
1930V450
1930V491
1930V500
1930V541
1930V560
1930V591
1930V600
1930V641
1930V691
1930V750
1930V991
1930V1091
2026V422
2026V445
2026V607
2126V309
2126V365
2226V307
2230V266
2230V273
2230V275
2230V285
2230V326
2230V375
2322V329
2322V347
2322V364
2322V384
2322V396
2322V421
2322V434
2322V441
2322V461
2322V481
2322V521
2322V541
2322V601
2322V621
2322V661
2322V681
2322V701
2322V721
2322V801
2322V826
2322V846
2322V886
2322V921
2322V1001
2322V1061
2322V1271
2326V310
2326V359
2330V273
2330V338
2426V343
2430V297
2430V302
2430V319
2430V345
2430V379
2436V331
2526V314
2530V300
Metric and asymmetric sizes available in minimum quantities.
106
2530V335
2530V490
2530V500
2530V530
2530V550
2530V575
2530V595
2530V600
2530V610
2530V630
2530V660
2530V670
2530V690
2530V700
2530V730
2530V750
2530V790
2530V840
2530V850
2530V890
2530V934
2530V990
2530V1090
2626V369
2626V388
2630V345
2630V395
2636V332
2822V778
2826V452
2830V337
2830V363
2830V366
2830V367
2830V393
2830V396
2830V422
2830V428
2836V343
2836V350
2836V380
2926V366
2926V400
2926V426
2926V471
2926V477
2926V486
2926V491
2926V521
2926V534
2926V546
2926V574
2926V586
2926V606
2926V616
2926V636
2926V646
2926V666
2926V686
2926V706
2926V726
2926V776
2926V786
2926V834
2926V856
2926V891
2926V906
2926V921
2926V966
2926V1006
2926V1026
2926V1086
2926V1106
2926V1146
3230V1120
3230V1180
2930V348
2930V420
3236V369
3236V389
3236V432
3226V392
3226V395
3226V400
3226V433
3226V439
3226V450
3226V465
3226V505
3226V514
3226V545
3226V585
3226V603
3226V650
3226V663
3226V723
3226V783
3226V843
3226V903
3226V963
3226V1023
3226V1083
3230V419
3230V481
3230V600
3230V621
3230V630
3230V670
3230V710
3230V750
3230V771
3230V800
3230V850
3230V900
3230HV528
3230HV546
3230HV553
3230HV570
3230HV585
3230HV603
3230HV613
3230HV620
3230HV626
3230HV644
3230HV685
3230HV702
3230HV723
3230HV821
3230HV856
3230HV931
3230HV960
3230HV1060
3430V424
3430V476
3430V493
3432V450
3432V456
3432V480
3432V484
3432V528
3432V534
3630V455
3726V558
3826V465
3830V510
3830V517
3830V580
3830V587
4430V530
4430V548
4430V555
4430V560
4430V570
4430V578
4430V600
4430V610
4430V630
4430V652
4430V660
4430V670
4430V690
4430V700
4430V710
4430V718
4430V730
4430V740
4430V750
4430V760
4430V780
4430V790
4430V800
4430V850
4430V900
4430V910
4430V930
4430V950
4430V970
4430V1000
4430V1030
4430V1060
4430V1090
4430V1120
4430V1150
4430V1180
4430V1250
4430V1320
4430V1410
4430V1460
4430V1610
4436V525
4436V551
4436V646
3836V418
3836V426
3836V654
3836V794
4630V650
4630V663
4630V733
4030V590
4636V613
4036V541
4036V574
4230V556
4230V605
4230V653
4430V510
4830V602
4830V653
4830V699
4830V730
4830V750
4830V850
4830V970
4830V1070
4836V618
4836V655
4836V670
4836V710
4836V800
4836V850
4836V900
4836V950
4836V1000
4836V1060
4836V1120
4836V1180
4836V1250
5130V732
5130V787
5228V930
5230V662
5230V734
5230V867
5636V774
5830V756
5836V737
6236V607
6236V725
6236V762
P O W E R
T R A N S M I S S I O N
S P E C I A L T Y
P R O D U C T S F l a t B e l ti n g
2 0 1 0
(Truly Endless)
A pp l i c a t i o n s
Handles a wide range of horsepower and speeds in both
industrial and agricultural drives.
•Harvesting Equipment
• Soil Handling
•Textiles and Forestry
• Food Processing
•Hay Equipment
• Chain Replacement
•Industrial Equipment
• Health and Fitness
•Direct Gear Drive Replacement • Material Handling
Key Features & Benefits
T r u l y E n d l e ss C o m p a ss ®
Synthetic Cord Belts
These belts are extremely flexible and exceptionally long-lasting,
even when operating over small pulleys. They are made in four
different weights to meet any service requirement.
Goodyear Engineered Products Compass Cord transmission belts
are made with a single-layer, reinforcing section for a cross section
which is thinner by 25% or more compared to plied belts of
equal horsepower capacity. The high-tensile strength, multistrand
synthetic cords used in Compass Cord belts provide maximum
strength and minimum elongation.
Compass belts are furnished in an abrasion-resistant rubber
construction. They can be made with oil-resisting synthetic
rubber compounds on special order in widths from 1˝ to 36˝ and
lengths from 25˝ to 135´.
T r u l y E n d l e ss C o m p a ss
250 & 450 Steel Cable Belts
These Compass Belts are constructed with steel cable for
heavy-duty drives. These belts include the features of Compass
Cord belts with the added advantage that the load-carrying
members are very finely stranded steel cables instead of synthetic
rope cords. All Compass 250 and 450 belts are made with
oil-resisting compounds throughout, which gives them greatly
increased life under operating conditions where oil is present.
•Smooth, quiet operation and long belt life.
•Uniform belt surface with no splicing.
•High-tensile strength.
•High coefficient of friction.
•Lightweight.
•No lubrication necessary.
•Transverse rigidity.
We manufacture a complete line of flat belting from
Truly Endless Compass and Multiple Ply belts to
Regulator Power Strap flat belts for the health and
fitness industry.
T r u l y E n d l e ss M u l t i p l e P l y B e l t s
The Multiple Ply belt is another product in the Truly Endless
line. The round-and-round fabric construction can be split into
multiple belts from one slab, representing great cost savings.
Various carcass materials are available for Multiple Ply belts,
depending on the application. The most highly recommended
are polyester/nylon, cotton, nylon, polyester, etc. These belts can
be supplied with rubber covers, friction surface, or bareback. We
can supply V-guides, banner edges, cleats, drive lugs, and rough
top surfaces.
S P E C I A L T Y
Part No: Compass “L” Flat Belt
They generally handle much higher horsepower loads than any
conventional fabric or cord construction belt, are extremely
flexible, and readily conform to small pulleys.
To learn more visit www.goodyearep.com/ptp.
107
P O W E R
T R A N S M I S S I O N
S P E C I A L T Y
P R O D U C T S F l a t B e l ti n g
Per Foot
Compass® L (Drum Cured)
Compass L (Press Cured)
Compass M (2˝ to 9˝ wide incl) (1 x 2 env)
Compass M (10˝ to 28˝ wide incl) (2 x 3 env)
Compass C
Compass H
Compass 250 (4˝ to 36˝)
Compass 250 (4˝ to 36˝)
Compass 250 (10˝ & over)
Compass 450 (to 10˝)
Compass 450 Steel (10˝ & over)
(Truly Endless)
Weight P.I.W.
Inches
Thickness
Cord
0.0614
0.0940
0.0990
0.1470
0.1640
0.1820
0.1460
0.1740
0.2000
0.2110
0.2470
9/64
13/64
15/64
21/64
21/64
3/8
11/64
15/64
19/64
17/64
21/64
Rayon
Rayon
Rayon
Rayon
Polyester
Polyester
Steel
Steel
Steel
Steel
Steel
For figuring belt weights on all Compass Belting with Rubber Covers, add the following:
COVERS — PIW 1⁄32˝ Ga. Lbs/Ft
Wingprene® — ORS
Rubber — ABR
.0196 lb.
.0160 lb.
Other Useful Compass Endless Belt Information:
S P E C I A L T Y
Drum Cured
Compass L
Compass M
Press Cured
Compass M
Compass C
Compass H
*Compass 250 Steel
Compass 450 Steel
Min. Width
Max. Width
Min. Length
Max. Length
1˝
2˝
10˝
28˝
241⁄2˝
241⁄2˝
120˝
1695⁄8˝
Min. Width
Max. Width
Min. Length
Max. Length
2˝
4˝
4˝
4˝ 10˝ 36˝ 36˝ 36˝ 36˝ 36˝ 120˝ 120˝ 120˝ 120˝ 120˝ 135´
135´
135´
135´
135´
Press Cured belts 30˝ to 34˝ wide require a minimum length of 14´ (168˝).
Press Cured belts above 36˝ wide require a minimum length of 17´ (204˝).
* Compass 250 Steel belts under 120˝ maximum width of 18˝, over 120˝ limitations do not apply (up to 38˝).
NOTE: Belting made by continuous build endless method has a length tolerance of plus or minus 1%.
108
P O W E R
T R A N S M I S S I O N
S P E C I A L T Y
P R O D U C T S 2 0 1 0
Truly Endless Belts
Available Drum Sizes
Drum Built Belts are made only in raw-edge construction in lengths shown below.
Lengths other than shown below are available with procurement of tooling. Contact Customer Service for availability.
43 3 ⁄4
12
13 7 ⁄8
15 3 ⁄4
241 ⁄2
251 ⁄2
261 ⁄2
27 3 ⁄8
27 7⁄8
2811⁄16
291 ⁄8
30 3 ⁄16
30 13 ⁄16
311 ⁄2
321 ⁄8
321 ⁄4
325 ⁄8
33
3311⁄16
341 ⁄4
349 ⁄16
351 ⁄8
351 ⁄2
3513 ⁄16
36
361 ⁄2
37
37 5⁄8
37 3⁄4
38
385 ⁄8
40
401 ⁄2
40 3 ⁄4
411 ⁄4
415 ⁄8
417⁄8
42 5 ⁄8
431 ⁄2
441 ⁄8
461 ⁄4
461 ⁄2
47 3 ⁄16
47 3 ⁄8
47 5 ⁄8
481 ⁄4
48 3 ⁄8
491 ⁄4
49 5 ⁄8
4911⁄16
50
50 3 ⁄16
511 ⁄8
515 ⁄8
52
52 5 ⁄16
521 ⁄2
53 3 ⁄8
54
541 ⁄8
55
56
56 3 ⁄8
58
581 ⁄2
58 5 ⁄8
59
60
611 ⁄2
62
63
631 ⁄2
641 ⁄8
65
66
661 ⁄8
67
68
681 ⁄2
68 5 ⁄8
69
69 5 ⁄8
70
71
711 ⁄2
72
74
74 3 ⁄4
761 ⁄2
78
79
791 ⁄2
80
801 ⁄4
81
821 ⁄4
82 3 ⁄4
84
85
86
861 ⁄2
88
89
891 ⁄2
901 ⁄8
91
92
921 ⁄2
92 3 ⁄4
931 ⁄2
94
941 ⁄4
95
96
961 ⁄2
98
991 ⁄4
101
1011 ⁄2
1021 ⁄2
103
1031 ⁄2
1041 ⁄2
105
1081 ⁄2
109 3 ⁄4
1113 ⁄16
1121 ⁄2
1131 ⁄2
1141 ⁄4
115
1151 ⁄4
1161 ⁄2
117 3 ⁄4
120
1211 ⁄2
125
126
128
13011⁄16
135 3 ⁄4
138 7⁄ 8
141
143 3 ⁄4
145
147 3 ⁄4
1511 ⁄4
154
156
157
1591 ⁄2
162
1621 ⁄2
163
168 5 ⁄8
S P E C I A L T Y
DRUM SIZES
10 3 ⁄8
109
P O W E R
T R A N S M I S S I O N
P R O D U C T S S P E C I A L T Y
Bowling Machine
AMF
Part Number
000-022-099
000-025-731
000-026-753
000-027-710
000-028-864
000-028-865
000-029-600
030-003-912
030-005-197
Brunswick
Part Number
AMF
Part Number
Goodyear Engineered Products
Part Number
A112
8350
CARPET
2L360
8690
8695
8640
A133
B128
030-005-453
030-008-671
030-008-792
070-001-424
070-002-005
82-70-2013
000-029-433
057-001-003
146-004-772
Brunswick
Part Number
Goodyear Engineered Products
Part Number
10-635112
10-635126
10-635303
10-635304
10-635308
10-635309
10-635314
12-150113
8555
8505
A90
A64
4L335
A80
4L350
8620
12-300082-3
12-400034-2
12-400034-3
12-400034-4
12-400034-5
12-400223
12-400227
12-400314
Goodyear Engineered Products
Part Number
8520
A133
A133
2L360
B190
8685
3L360
4L410
5M1850
Goodyear Engineered Products
Part Number
8625
A75
A105
A120
B195
8615
B205
AX112
AMF
Part Number
Goodyear Engineered Products
Part Number
146-004-775
208-111-174
070-011-064
070-011-147
070-011-148
234-001-147
702-504-012
702-504-013
Brunswick
Part Number
5M925
3L450
3L450
3L380
3L400
8595
A68
A34
Goodyear Engineered Products
Part Number
12-400329
12-200947
116-31-290
10-635317
53-530230-2
53-520148-2
A77
8560
3L310
AX90
8420
8430
S P E C I A L T Y
C o tt o n C l e a n e r
A pp l i c a t i o n s
Synchronous belts specially designed for driving the
cylinders on Cotton Gin Incline cleaner machines.
Key Features & Benefits
• Steel tensile cords.
•Long service life in harsh environments.
Part No: 64 CCB
64 64˝ Pitch Length
CCB 1˝ Pitch
Size
61CCB142
63CCB165
64CCB170
65CCB175
110
Pitch Length
61.0˝
63.0˝
64.0˝
65.0˝
No. of Teeth
61
63
64
65
P O W E R
T R A N S M I S S I O N
S P E C I A L T Y
P R O D U C T S Ax i a l F a n
®
2 0 1 0
Belts
A pp l i c a t i o n s
Specific application power transmission synchronous
belts used primarily in the chemical, petroleum, and
refining industries.
Key Features & Benefits
Part Number
SAP No.
No. of Teeth
3150 14M 55\FFAN
3150 14M 85\FFAN
3360 14M 55\FFAN
3360 14M 85\FFAN
3500 14M 55\FFAN
20081711
20081712
20081835
20081836
20081963
225
225
240
240
250
Part Number
3500 14M 85\FFAN
3850 14M 55\FFAN
3850 14M 85\FFAN
SAP No.
No. of Teeth
20081964
20082161
20082162
250
275
275
Specific application power transmission synchronous belts used primarily in the chemical, petroleum and refining industries. Fin Fan is a registered trademark of
the Hudson Products Company.
Ax i a l F a n
Part No.
F168-14M-40-E
F168-14M-55-E
F168-14M-85-E
SAP No.
Wt.*
Part No.
20182173
20182174
20182175
88.0
94.0
108.0
F192-14M-40-E
F192-14M-55-E
F192-14M-85-E
S P E C I A L T Y
• Special Fin Fan construction.
•Universal tooth profile drops into existing HTD
sprockets.
•Quiet tooth engagement.
•High-grade engineered rubber compound.
•Fiberglass tension cords for excellent resistance
to shrinkage/elongation.
•Oil, heat, ozone, and abrasion resistance.
•Low-maintenance/high-efficiency rating.
Part No: 3150 14M 55\FFAN
3150 3150mm Pitch Length
14 14mm Pitch
55 55mm Wide
\FFAN Special Fin Fan® Construction
Sprockets
SAP No.
Wt.*
Part No.
20182176
20182177
20182178
102.0
110.0
130.0
F216-14M-40-E
F216-14M-55-E
F216-14M-85-E
SAP No.
Wt.*
20182179
20182180
20182181
136.0
145.0
161.0
*Weight does not include bushing.
To learn more visit www.goodyearep.com/ptp.
111
P O W E R
T R A N S M I S S I O N
P R O D U C T S A U T O M O T I V E
Gatorback Poly-V Belt
®
®
A pp l i c a t i o n s
For passenger cars and light- and heavy-duty trucks.
Key Features & Benefits
Part No: 4061025
4
K Section Poly-V
06
6 Ribs
1025 102 5 ⁄10 Length
•Specially treated tension members to maintain
tension and resist elongation on both locked center
drives and spring tension systems.
•Fiber-reinforced rubber helical cogged
ribs offer maximum cord support and wear
resistance for unsurpassed performance in high
horsepower applications.
•The backing is tough, coated fabric material
impregnated with premium rubber for heat and
oil resistance to provide high coefficient of friction
needed to drive flat pulleys.
•Unique helical cog design runs quieter than standard cogged belts.
Gatorback V-Belt
A pp l i c a t i o n s
For passenger cars and light- and heavy-duty trucks.
Key Features & Benefits
A U T O M O T I V E
Part No: 15456
15 ⁄32˝ Top Width
15
456
456 ⁄8˝ Outside Length
•High-strength Vytacord® tension members resist
shockload failure. Low-elongation properties assure
uniform performance over the long life of the belt.
•Fiber-reinforced rubber helical cogs offer greater flexibility which reduces cracking and fatigue in the cushion member.
•Tension fabric impregnated with engineered
oil-resistant rubber reduces surface fatigue and resists cracking.
•Rubber edges maintain positive, no-slip contact
with pulley grooves for reliable energy transfer.
To learn more visit www.goodyearep.com/ptp.
112
P O W E R
T R A N S M I S S I O N
P R O D U C T S A U T O M O T I V E
2 0 1 0
Timing Belt
A pp l i c a t i o n s
Goodyear Engineered Products Timing belts are
designed to deliver precise timing over a long service
life in demanding automotive cam applications.
Key Features & Benefits
•Precision-molded teeth made of synthetic
polymers provide high strength, shear resistance,
and environmental resistance to assure long,
dependable life.
•Specially woven and chemically treated fabric is
impregnated with our high-grade rubber polymers
to reduce pulley friction and provide outstanding
resistance to abrasion, oil, and ozone.
•Special fiberglass tension members are
dimensionally stable and high in strength, starting
out precise and dependable and staying that way.
•Durable polymer backing protects the load carrying cords from oil, abrasion, and ozone.
It also keeps the cords in place so they pull
together smoothly and evenly.
Part No: 40138
40
Automotive Timing Belt
138
Industry Standard Description
A pp l i c a t i o n s
Main drive belts for truck refrigeration units, especially
designed for long life on mule drives and backside
idler drives. Accessory drives are also found in the
refrigeration units and are driven by Hex belts,
Torque-Flex® belts, and Insta-Power® belts.
Key Features & Benefits
A U T O M O T I V E
T r u c k R e f r i g e r a ti o n B e l t
•Premium rubber-impregnated fabric resists oil,
heat, and wear.
•High-strength Vytacord® tension members
improve flex life, eliminate excess elongation, and increase resistance to shock loads.
•Cushion section is made of premium rubber to
resist heat and wear.
Part No: 41047
Note: For an application guide and available sizes of Gatorback® V-belts, Poly-V® belts, Truck Refrigeration belts, Special Truck belts, and Timing belts, ask your
distributor for the following catalogs:
Catalog Description
Part Number
Catalog Description
Car & Light Truck Application Guide (Current to 1994)
Car & Light Truck Application Guide (1993 & Prior)
20035740
20049146
Medium to Heavy Duty Truck Application Guide (Current to 1990) 20049138
Medium to Heavy Duty Truck Application Guide (1989 & Prior)
20108695
Part Number
113
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
B e l t S i z e I n f o r m a ti o n
HY - T ® C l a s s ic a l V - B e l t s / T o r q u e - F l e x ®
Section
A, AX
B, BX
C, CX
D, DX
E
How to Obtain Effective Outside
Length Up To 210˝
How to Obtain Effective Outside
Length Over 210˝
Add 2.1˝ to Part Number Ex: A20 = 22.1˝ Add 2.9˝ to Part Number Ex: B100 = 102.9˝
Add 4.2˝ to Part Number Ex: C100 = 104.2˝
Add 5.2˝ to Part Number Ex: D180 = 185.2˝
Add 7.0˝ to Part Number Ex: E180 = 187.0˝
Add 2.1˝ to Part Number Ex: A220 = 22.1˝
Add 1.4˝ to Part Number Ex: B240 = 241.4˝
Add 2.2˝ to Part Number Ex: C240 = 242.7˝
Add 2.7˝ to Part Number Ex: D240 = 242.7˝
Add 3.5˝ to Part Number Ex: E360 = 363.5˝
Nominal
Top Width
1 ⁄2˝
21 ⁄32˝
7⁄ 8 ˝
11 ⁄4˝ 11 ⁄2˝ (.500)
(.656)
(.875)
(1.250)
(1.500)
HY - T ® W e d g e
Section
3V, 3VX
5V, 5VX
8V
Nominal
Top Width
3⁄ 8 ˝
5⁄ 8 ˝
1˝
(.375)
(.625)
(1.000)
Lengths
Belt Number indicates nominal
Outside Length
Example: 3VX475 = 47.5˝
FH P
Section
Nominal
Top Width
1 ⁄4˝
2L
3L
4L
5L
3 ⁄8˝
1 ⁄2˝
21 ⁄32˝
(.250)
(.375)
(.500)
(.656)
Lengths
Belt Number indicates nominal
Outside Length
Example: 4L400 = 40.0˝
P o s iti v e D r i v e
Pitch
Distance from center of one tooth to center of next
MXL = .080˝ XL = .200˝ L = .375˝ H = .500˝ XH = .875˝ XXH = 1.250˝
Width
Last digits of belt number are the width in inches and tenths
Example: 240XL025 = 1 ⁄4˝ width
Length
First digits of belt number are the pitch length in inches and tenths
Example: 240XL025 = 24.0˝ Pitch length
P o l y - V®
GENERAL
INFORMATION
114
Section
Width per Rib
Thickness
J
L
M
.092
.185
.370
.16 .38
.66
Length
First digits are pitch length in inches and tenths
Example: 180J4 = 18.0˝ J = Poly-V cross section 4 = number of ribs
Variable Speed
First two digits of belt number indicate belt top width in sixteenths of an inch
Top Width Example: 3226V585 = 32 ⁄16˝ or 2˝ top width
Second two digits of belt number indicate the pulley angle
Angle
Example: 3226V585 fits a 26°-angle pulley
Last digits of belt number are the pitch length
Length
Example: 3226V585 = 58.5˝ pitch length
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
2 0 1 0
T e c h n ic a l I n f o r m a ti o n
S p r o c k e t I n s t a l l a ti o n
Follow all safety policies and requirements of federal, state, and
local authorities, as well as the regulation of the employer, when
working on power equipment. Always lock out the power source
to the machinery before performing any work.
Preparation
OBJECTIVE: Verify that all necessary tools and parts are available and ready for installation.
1. Eagle NRG™ belts and sprockets are identified with a
unique Color Spectrum System. The seven colors used
for identification are Yellow, White, Purple, Blue, Green,
Orange, and Red. Each color represents a different size so that
Blue belts are made to operate with Blue sprockets. Make sure
the same color belt and sprockets have been obtained. When
installing Falcon HTC®, Hawk Pd® and Blackhawk Pd®, it is
also important that the correct sprocket width is used.
2. The following tools are recommended for proper belt and
sprocket installation.
• Straightedge • Tape measure
• Socket and open-end wrenches • File and sandpaper
• Torque wrench
• Clean cloth
• Belt tension gauge
• Deflection force values
• Laser Alignment
for tensioning the belt
Sprocket & Bushing Installation
OBJECTIVE: Align the sprockets and secure them to the shafts.
1.For conventional mounting, insert bushing into the sprocket,
aligning the tapped holes in the bushing flange with the
drilled holes in the sprocket hub.
2.Insert capscrews through the drilled holes and into the tapped
holes.
3.Insert the key into the keyseat of the shaft.
Shaft 1
Shaft 2
See pages 129 – 130 for tools offered and how to order.
GENERAL
4. Make sure the shafts are true and parallel by accurately
measuring the distance between the shafts at three points
along the shaft. The distance between the shafts should be the
same at all three points as shown. Also make sure the shafts
are rigidly mounted. Shafts should not deflect when the belt
is tensioned.
INFORMATION
3. Make sure the components are ready for installation. Clean
all shafts, removing any nicks or burrs. Clean all mating
surfaces of the sprocket, bushing, and shaft. No lubrication
or anti-sieze solution should be used on any of these surfaces,
including threaded holes. Use of lubrication can create higher
torque, which will cause premature failure.
115
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
T e c h n ic a l I n f o r m a ti o n
4.
With capscrews to the outside, place the sprocket and
bushing assembly on the shaft, positioning the assembly
with the bushing flange towards the shaft bearings.
Reverse mounting the “Quick Detachable” (QD)
bushing can be advantageous for some applications.
5.
Repeat Steps 1 – 4 for the other sprocket.
6.
Check that the teeth of both sprockets are pointing in the
same direction when installing Eagle NRG™ sprockets.
7.
Snug the capscrews so that the sprocket/bushing
assembly can still move on the shaft.
8.
Align the sprockets using a straightedge. Check for
contact in four places as shown. Do not use bearings or
drive shafts as reference points for sprocket alignment.
Goodyear Engineered Products Laser Alignment Tool
provides an alternative method for checking alignment.
9.
Using a torque wrench, tighten the capscrews to the
torque values listed below. If there is not a gap of 1/8”
to 1 ⁄4˝ between the bushing flange and the sprocket hub
then disassemble the parts and determine the reason for
the faulty assembly.
10. The sprocket will draw onto the bushing during
tightening. Always recheck alignment after tightening
the capscrews. If alignment has changed, return to
Step 7.
Torque Specifications
Bushing
Capscrew SetscrewSetscrew
Torque
Torque
Size
(in-lb) (ft-lb) (in-lb) (in)
H
108
9
–
–
SH 108 9
87 1/4
11. Tighten the setscrews over the keyway to the torque
values listed in the table to the right.
SDS 108 9
87 1/4
SK 180 15 87 1/4
12. If the sprockets are straight bore, use the above
alignment procedure and then tighten the setscrews
to the correct torque for the setscrew size listed in the
Torque Specifications table.
SF 360 30 166 5/16
E
720 60 290 3/8
F
900 75 290 3/8
J
1620 135 290 3/8
M
2700 225 290 3/8
N
3600 300 620 1/2
QD bushings can be installed with the capscrews on either
side, excluding H, M, and N sizes. Drives with opposing shafts
require one of the sprockets be mounted with the capscrews
on the flange side and one with the capscrews on the hub side.
GENERAL
INFORMATION
116
Contact
Points
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
2 0 1 0
T e c h n ic a l I n f o r m a ti o n
B e l t I n s t a l l a ti o n & T e n s i o n i n g
Before beginning, inspect the belt for damage and verify that
the sprockets are properly mounted. Refer to sprocket and bushing manufacturer installation procedure. Belts should never be
crimped or bent to a diameter less than the minimum sprocket
diameter, approximately 2.5 inches for 8mm belts and 5 inches
for 14mm belts.
1. Shorten the center distance or release the tensioning idler to
install the belt. Do not pry the belt onto the sprocket. Refer
to the following Center Distance Allowance tables for required
center distance adjustment.
Shorter Center Distance
for Synchronous Installation
Pitch Length
Range (mm)
Allowance (Decrease)
for Installation
8M Belts 14M Belts
(mm/in)
Less than 1525
22.5/0.9
1525 –3050
25.0/1.0
Greater than 3050 27.5/1.1
Allowance (Decrease)
for Installation
8M Belts 14M Belts
(mm/in)
Less than 1525
34.5/1.4
1525-3050
37.0/1.5
Greater than 3050 39.5/1.6
Longer Center Distance
for Synchronous Belt Take-Up
Apply the following center distance allowances for the
Hawk Pd® and Falcon HTC®. A center distance adjustment, or decrease in center distance, is necessary to install
a belt. In addition, an increase in center distance will be
necessary for proper tensioning. If you install a belt
together with sprockets, allow the following decrease in
center distance for installation and an increase in center
distance for tensioning.
Pitch Length
Range (mm)
Less than 1525
1525-3050
Greater than 3050
Allowance (Decrease) Allowance (Increase)
for Installation
for Take-Up
8M, 14M Belts
8M, 14M Belts
(mm/in)
(mm/in)
2.5/0.1
5.0/0.2
7.5/0.3
2.5/0.1
5.0/0.2
7.5/0.3
2.5/0.1
5.0/0.2
7.5/0.3
If you install the belt over two flanged sprockets that
are already installed on the drive, allow the following
decrease in center distance for installation and increase
in center distance for tensioning.
Pitch Length
Range (mm)
Center Distance
36.5/1.4
39.0/1.5
41.5/1.6
Allowance (Increase)
for Take-Up
8M, 14M Belts
(mm/in)
59.2/2.3
62.0/2.4
64.5/2.5
Allowance (Increase)
for Take-Up
8M, 14M Belts
(mm/in)
2.5/0.1
5.0/0.2
7.5/0.3
Consider the following center distance allowances when
installing Eagle NRG™ sprockets. Since flanges are not
necessary on Eagle NRG drives, only one table of center
distance allowances is provided.
Pitch Length
Range (mm)
Allowance (Decrease)
for Installation
8M Belts 14M Belts
(mm/in)
Less than 1525
10.1/0.4
Greater than 1525 15.2/0.6
15.2/0.6
17.8/0.7
Allowance (Increase)
for Take-Up
8M, 14M Belts
(mm/in)
2.5/0.1
5.0/0.2
2. Place the belt on each sprocket and ensure proper engagement
between the sprocket and belt teeth.
3. Lengthen the center distance or adjust the tensioning idler to
remove any belt slack.
4. Using a tape measure, measure the span length of the drive.
Refer to dimension “P” in the diagram below. The span length
can be calculated using the below formula.
INFORMATION
Goodyear Engineered Products Synchronous timing belts
must be installed and tensioned properly to ensure optimum
performance. Sprocket alignment must be preserved while
tensioning the drive.
If you install a belt over one flanged sprocket and one
unflanged sprocket with the sprockets already installed
on the drive, allow the following decrease in center
distance for installation and increase in center distance
for tensioning.
GENERAL
OBJECTIVE:
117
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
T e c h n ic a l I n f o r m a ti o n
5. Place a straightedge or reference line across the top of the belt.
6. Determine the proper deflection force to tension the belt.
Deflection forces are given in the following tables. Deflection
forces are also given on the output of the MaximizerPro™
computer drive analysis.
a) If using a tension gauge, the deflection scale is calibrated in
inches of span length. Check the force required to deflect the
belt the proper amount. There is an O-ring to help record the
force. If the measured force is less than the required deflection
force, lengthen the center distance. If the measured force is
greater than the required deflection force, shorten the center
distance. See chart on page 119 for deflection values and
tension gauges available.
7. After the belt is properly tensioned, lock down the center
distance adjustments and recheck the sprocket alignment.
8.If possible, run the drive for approximately 5 minutes with or
without load. Stop the drive and lock out the power source
and examine alignment, capscrew torque and belt tension.
Adjust the center distance to increase the belt tension to the
“New” value in the Table on page 86. Lock down the drive
adjustments and recheck tension.
9.Recheck the belt tension, alignment, and capscrew torque after
eight hours of operation to ensure the drive has not shifted.
b)If using other means to apply force to the belt, adjust the
center distance so that the belt is deflected 1⁄64 per inch of
span length when the proper force is applied. See chart on
page 119 regarding TensionRite® Belt Frequency Meter
which calculates belt tension by measuring span vibrations.
P. Span Length
D. Diameter (in)
F. Force (lbs)
GENERAL
INFORMATION
118
Q. Deflection (in)
d. Diameter (in)
C. Center Distance (in)
F = Deflection Force
q = Deflection, 1 ⁄64˝ per inch of span length
C = Center Distance
D = Large Sprocket Pitch Diameter
d = Small Sprocket Pitch Diameter
P = Span Length
P=
C2 - (
D-d
2
)2
P O W E R
T R A N S M I S S I O N
GENERAL
P R O D U C T S INFORMATION
2 0 1 0
T e c h n ic a l I n f o r m a ti o n
D e f l e cti o n F o r c e s
for
Belt Tensioning (lbs)
Deflection Forces for Belt Tensioning (lbs.)
Part Number
Eagle NRG™
Yellow
White
Purple
Blue
Green
Orange
Red
NEW
BELT
15
30
60
54
80
107
161
USED
BELT
11
21
43
38
57
76
115
NEW
BELT
12
24
47
44
66
88
131
USED
BELT
8
17
34
31
47
63
94
NEW
BELT
9
19
38
38
57
76
115
USED
BELT
7
13
27
27
41
55
82
Falcon HTC®
1000-up RPM
8GTR 12
8GTR 21
8GTR 36
8GTR 62
14GTR 20
14GTR 37
14GTR 68
14GTR 90
14GTR 125
24
42
72
124
38
70
129
171
238
17
30
51
88
29
54
99
131
181
14
25
42
72
31
57
105
140
194
10
18
30
52
23
43
78
104
144
9
16
27
47
28
52
95
126
175
7
12
21
36
21
39
71
95
131
Blackhawk Pd®
101-1000 RPM
8MBH 12
8MBH 22
8MBH 35
8MBH 60
14MBH 20
14MBH 42
14MBH 65
14MBH 90
14MBH 120
12
23
36
62
36
76
117
162
217
9
17
26
45
26
55
85
118
157
9
16
26
45
27
57
89
123
164
7
12
19
33
20
42
65
90
119
7
13
21
36
23
49
76
105
139
5
10
16
27
17
36
55
77
102
Hawk Pd®
Belt Type
0-100 RPM
8M 20
8M 30
8M 50
8M 85
14M 40
14M 55
14M 85
14M 115
14M 170
15
23
39
69
47
70
116
162
249
11
17
29
50
34
51
84
118
181
13
20
35
61
38
56
93
130
201
10
15
26
45
28
41
68
95
146
12
19
32
56
32
48
79
110
171
9
14
24
41
24
35
58
80
125
®
TensionRite Eagle NRG Tension Tester
(PN 20039446) or TensionRite Small Tension
Tester (PN 20044882)
A pp l i c a t i o n
≤
30 lbs Deflection Force
Part Number
TensionRite Eagle NRG
Tension Tester (PN 20039447)
or TensionRite Small Tension
Tester (PN 20083773)
A pp l i c a t i o n
≥
30 lbs Deflection Force
B e l t S t r a n d T e n s i o n ( LBS )
Belt Strand Tension (lbs.)
Part Number
Eagle NRG™
Belt
Weight
(kg/m)
Yellow
White
Purple
Blue
Green
Orange
Red
NEW
BELT
224
449
897
817
1210
1618
2436
USED
BELT
160
305
625
561
842
1122
1700
NEW
BELT
176
353
689
657
986
1314
1956
USED
BELT
112
241
481
449
682
914
1364
NEW
BELT
128
273
545
561
842
1122
1700
USED
BELT
96
177
369
385
586
786
1172
Falcon HTC®
8GTR 12
8GTR 21
8GTR 36
8GTR 62
14GTR 20
14GTR 37
14GTR 68
14GTR 90
14GTR 125
370
648
1111
1913
571
1052
1939
2570
3578
258
456
775
1337
427
796
1459
1930
2666
210
376
631
1081
459
844
1555
2074
2874
146
264
439
761
331
620
1123
1498
2074
130
232
391
681
411
764
1395
1850
2570
98
168
295
505
299
556
1011
1354
1866
0.064
0.112
0.192
0.330
0.163
0.301
0.550
0.738
1.023
8MBH 12
8MBH 22
8MBH 35
8MBH 60
14MBH 20
14MBH 42
14MBH 65
14MBH 90
14MBH 120
179
345
539
928
553
1167
1796
2487
3332
131
249
379
656
393
831
1284
1783
2372
131
233
379
656
409
863
1348
1863
2484
99
169
267
464
297
623
964
1335
1764
99
185
299
512
345
735
1140
1575
2084
67
137
219
368
249
527
804
1127
1492
0.045
0.069
0.159
0.226
0.164
0.344
0.532
0.737
0.983
8M 20
8M 30
8M 50
8M 85
14M 40
14M 55
14M 85
14M 115
14M 170
226
347
590
1046
715
1069
1778
2486
3827
162
251
430
742
507
765
1266
1782
2739
194
299
526
918
571
845
1410
1974
3059
146
219
382
662
411
605
1010
1414
2179
178
283
478
838
475
717
1186
1654
2579
130
203
350
598
347
509
850
1174
1843
0.118
0.176
0.289
0.507
0.438
0.583
0.913
1.233
1.835
TensionRite Belt Frequency Meter
(PN 20278454)
INFORMATION
0.071
0.142
0.283
0.254
0.380
0.507
0.761
GENERAL
1000-up RPM
Blackhawk Pd®
101-1000 RPM
Hawk Pd®
Belt Type
0-100 RPM
1. The table values are typically larger than necessary to cover the broad RPM range.
2. For drives where hub loads are critical and high speed drives or other drives with special circumstances, the table values (deflection force, installation tension) should be calculated.
3. Consult the Web site for detailed information on using the frequency-based tension gauges.
4. Veyance Technologies offers three different tension gauges for properly tensioning Eagle NRG, Hawk Pd or Blackhawk Pd belts. See your Goodyear Engineered Products sales representative
or your local PTP industrial distributor for more information on the tension gauges listed on this page.
119
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
T e c h n ic a l I n f o r m a ti o n
Drive Alignment
Synchronous belts are very sensitive to misalignment. The
tension carrying member has a high tensile strength and resistance
to elongation, resulting in a very stable belt product. Any
misalignment will lead to inconsistent belt wear, uneven load
distribution, and premature tensile failure. In general,
synchronous drives should not be used where misalignment is a
problem. Misalignment should be limited to 1⁄4 degree or 1⁄16 inch
per foot of center distance.
With parallel shafts, misalignment occurs when there is an offset
between the sprocket faces as in Figure A. Misalignment also
occurs when the shafts are not parallel as in Figure B.
Figure B
Figure A
Misaligned
Any degree of misalignment will reduce belt life and cause edge
wear. Therefore, a straightedge should be used to check proper
alignment verifying that sprockets and shafts are parallel, as in
Figure C.
Figure C
Correct Alignment
A straightedge should touch the sprocket at the four points
indicated. Both front and back alignments should be checked.
Laser Alignment Tool
Goodyear Engineered Products Laser Alignment Tool provides an
alternative to checking alignment with a straightedge. Each laser
alignment tool comes with a rugged carrying case and detailed
instructions to get you started with the quickest, easiest, and most
versatile alignment tool on the market today.
GENERAL
INFORMATION
Aligned
Misalignment, at times, may cause tracking problems. Although
some tracking is normal and will not affect belt performance, it
may be caused by poorly aligned sprockets. Flanges may control a
tracking problem. Considering a two-sprocket drive, belt contact
on a single flange is acceptable. Belt contact with the opposite
flanges of two sprockets should be avoided.
120
Misaligned Aligned
Misalignment can also be attributed to the improper installation
of a bushing or loose drive framework. Refer to sprocket manufacture guidelines for proper bushing installation. Secure motor and
framework to eliminate vibration on center-to-center fluctuations.
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
2 0 1 0
T e c h n ic a l I n f o r m a ti o n
GENERAL
INFORMATION
Goodyear Engineered
P r o d u ct s V - B e l t
Causes of Premature
Failure
121
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
T e c h n ic a l I n f o r m a ti o n
Goodyear Engineered
P r o d u ct s S y n c h r o n o u s
Causes of Premature Failure
GENERAL
INFORMATION
122
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
2 0 1 0
M a n d r e l Q u a n tit y R e q u i r e m e n t s
F o r S p e ci a l L e n g t h
or
M a d e - t o - O r d e r B e l t s .*
The following quantities are for approximate reference only; mandrel tool sizes and availability at time of order may not be available. Please contact factory for verification.
A
B* C
D
E
68 50
42
25
---
®
HY-T Wedge Belts Envelope
124˝
3V
88
5V
50
8V
34
®
HY-T Wedge Belts Cut-Edge
3VX
5VX
Torque Team®
Belting
(Including
Torque-
Team
Plus and
Laminated)
3VX
5VX
8V
AX
BX
CX
DX
Up to
120˝
98
63
135 100
64
46
42
--50
32
24
21
124˝– 301˝
300˝ & Up
176
100
64
--50
32
120˝– 141˝– 300˝
140˝ 300˝ & Up
98
63
176
100
--50
Cut-Edge Envelope
25˝
116˝– 124˝ 301˝–
118˝
123˝ 300˝ & Up
95
54
---
60
50
36
29
3V
5V
8V
A
B
C
D
12˝–112˝
FHP Envelope
Length
*2L
---
4L
3L
104
5L
88
50
32
68
50
42
25
176
100
64
135
100
64
46
--50
32
--50
32
24
Under
120˝
120˝ Profile & Up
Standard Positive Drive
26˝ 26˝
26˝
26˝
26˝
26˝
Dual Positive Drive
26˝
26˝
26˝
26˝
MXL
XL
L
H
XH
XXH
n/a
n/a
n/a
13˝
13˝
13˝
XL
L
H
XH
--13˝
13˝
13˝
Hawk Pd® and Blackhawk Pd®
26˝
26˝
26˝
26˝
5M
8M
14M
20M
--13˝
13˝
13˝
Super Torque Positive Drive
(STPD)
28˝
28˝
28˝
27˝
26˝
3M
4.5M
5M
8M
14M
------14˝
13˝
Eagle NRG™ and Falcon HTC®: Contact Customer Service for correct quantities.
Variable Speed Belts
Hex Belts
AA
BB
CC
Any Length
38” Wide Mandrel**
0–
123˝
67
49
34
124˝– Over
300˝ 300˝
118
94
60
75
Under 38˝ &
38˝
Over
22/32
24/32
60
54
*2Ls unavailable in Envelope Construction.
28/32
32/32
45
39
FHP Cut-Edge
Dry Can Belts
2L
3L
4L
5L
Torque Flex® Belts
AX
BX
CX
DX
54
--47
30
Top 12˝–116˝
Cut-Edge Automotive Belts Width Length
13/32
98
87
15/32
17/32
76
Under 28˝ &
28˝
Over
75
Positive Drive Belting**
54
12˝–116˝
Length
240˝–300˝ 300˝ & Over
60
29
Neothane® Belts
152
98
79
63
Under
116˝
116˝
123˝
124˝
300˝
301˝
& Up
73
57
42
---
73
57
42
24
135
100
64
48
--50
32
24
5MR
7MR
11MR
12˝–118˝
Length
200
124
85
Poly-V® Belt (Cut-Edge Only)
“J” Section
“L” Section
“M” Section
“K” Section
1 0˝–120˝= 400 ribs
25˝–120˝ = 200 ribs
50˝–118˝ = 100 ribs
12˝–118˝ = 265 ribs
INFORMATION
>B38=>50 Pcs
<B38=>53 Pcs
Under 124˝– 301˝
123˝ 300˝ & Up
GENERAL
HY-T® Belts
*Nonstock Belts: Orders for nonstock or made-to-order belts are available in multiple mandrel size quantities. Please check factory for
availability of equipment and/or availability for the desired construction.
**Inches indicate the total top width mandrel yield (e.g., divide belt top width into yield for total number of belts per mandrel).
123
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
Belt Storage
General Guidelines
The storage of power transmission belts is of interest to users and
distributors as well as manufacturers. Under favorable storage
conditions, good quality belts retain their initial serviceability and
dimensions. Conversely, unfavorable conditions can adversely
affect performance and cause dimensional change. Good storage
facilities and practices will allow the user to achieve the most value
from belt products.
Some Things
to
Avoid
Do not store belts on floors unless a suitable container is
provided. They may be susceptible to water leaks or moisture or
otherwise damaged due to traffic.
Do not store belts near windows which may permit exposure to
sunlight or moisture. Do not store belts near radiators or heaters
or in the airflow from heating devices.
Do not store belts in the vicinity of transformers, electric motors,
or other electrical devices that may generate ozone. Also avoid
Methods
of
Power transmission belts should be stored in a cool and dry
environment with no direct sunlight. When stacked on shelves,
the stacks should be small enough to avoid excess weight on
the bottom belts which may cause distortion. When stored in
containers, the container size and contents should be sufficiently
limited to avoid distortion, particularly to those belts at the
bottom of the container.
areas where evaporating solvents or other chemicals are present
in the atmosphere.
Do not store belts in a configuration that would result in bend
diameters less than the minimum recommended sheave or
pulley diameter for normal bends and not less than 1.3 times the
minimum recommended diameters for reverse bends. (Refer
to appropriate RMA-MPTA-RAC Standards for minimum
recommended diameters.)
Storage
V-belts
A common method of storing belts is to hang them on pegs or
pin racks. Very long belts stored this way should use sufficiently
large pins or crescent-shaped “saddles” to prevent their weight
GENERAL
INFORMATION
Belt Cross Section
3L, 4L, A, AX, AA
5L, B, BX, 3V
9R, 13R, 13C, 13CX, 13D
16R, 16C, 16CX, 9N
Belt Length (in)
Under 60
60 up to 120
120 up to 180
180 and over
Belt Length (mm)
Under 1,500
1,500 up to 3,000
3,000 up to 4,600
4,600 and over No. of *Coils
0
1
2
3
No. of Loops
1
3
5
7
BB, C, CX
5V
16D, 22C, 22CX
15N
Under 75
75 up to 144
144 up to 240
240 and over
Under 1,900
1,900 up to 3,700
3,700 up to 6,000
6,000 and over
0
1
2
3
1
3
5
7
CC, D
22D, 32C
Under 120
120 up to 240
240 up to 330
330 up to 420
420 and over
Under 3,000
3,000 up to 6,100
6,100 up to 8,400
8,400 up to 10,600
10,600 and over
0
1
2
3
4
1
3
5
7
9
8V (25N)
Under 180
80 up to 270
270 up to 390
390 up to 480
480 and over
Under 4,600
4,600 up to 6,900
6,900 up to 9,900
9,900 up to 12,200
12,200 and over
0
1
2
3
4
1
3
5
7
9
*One coil results in three loops, two coils result in five loops, etc.
124
from causing distortion. Long V-belts may be “coiled” in loops
for easy distortion-free storage. The following is a guide to the
maximum number of coils for extended storage time.
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
2 0 1 0
Belt Storage
Methods
of
Storage
(Cont.)
Joined V-belts,
Synchronous Belts,
V - R i bb e d B e l t s
Like V-belts, these belts may be stored on pins or saddles with
precautions taken to avoid distortion. However, belts of these
types, up to approximately 120 inches (3000 mm), are normally
shipped in “nested” configuration and it is recommended that
the belts be stored in this manner as well. Nests are formed by
laying a belt on its side on a flat surface and placing as many belts
inside the first belt as possible without undue force. When the
nests are tight and are stacked with each rotated 180° from the
one below, they may be stacked without damage.
Variable Speed Belts
Variable Speed belts are more sensitive to distortion than
most other belts and it is not recommended that these belts be
hung from pins or racks. They should be stored on shelves.
A common method for packaging for shipment is the use of
a “sleeve” slipped over the belt. Variable Speed belts should
be stored in these sleeves and may conveniently be stacked on
shelves with the aid of the sleeves.
Belts of these types over approximately 120 inches (3000mm),
may be “rolled up” and tied for shipment. These rolls may be
stacked for easy storage. Care should be taken to avoid small
radii, which could damage the belts.
Storage
The quality of belts has not been found to change significantly
within seven years of proper storage at temperatures less than
85°F (30°C) and relative humidity below 70 percent. Also there
must be no exposure to direct sunlight.
If the storage temperature is increased beyond 85˚F (30°C), then
the storage limit for normal service expectancy should be reduced.
From a base of seven years at 85°F (30°C), the storage limit
should be reduced by one-half for each 15˚F (8°C) increase in
temperature. Under no circumstances should belts be exposed to
storage temperatures above 115°F (46°C).
Source: RMA IP-3-4, 2007
With a significant increase in humidity, it is possible for fungus
or mildew to form on stored belts. This does not appear to cause
serious belt damage, but should be avoided if possible.
Equipment using belts is sometimes stored for prolonged periods
(six months or more) before it is put in service or during other
periods when it is idle. It is recommended that the tension of
the belts be relaxed during such period and that equipment storage conditions should be consistent with the guidelines for belt
storage. If this is not possible, the belts should be removed and
stored separately.
INFORMATION
of
GENERAL
E f f e ct s
125
P O W E R
T R A N S M I S S I O N
GENERAL
P R O D U C T S INFORMATION
G o o d y e a r E n g i n e e r e d P r o d u ct s
M a tc h m a k e r S y s t e m
®
The RMA Engineering Standards IP-20 & IP-22 sets up limits for
matching Classical and Wedge V-belts having polyester cord based
on their lengths and cross-sections. These standards have been
developed to ensure that belts that meet the RMA tolerances will
run together on multiple-belt drives and effectively share the load
that is being transmitted.
V-Belt Permissible Deviation From Nominal Length - Envelope Narrow Profile
Industry Standard
Product Length
Range
0˝ to 50˝ – 63⁄64˝
51˝ to 80˝ – 63⁄64˝
81˝ to 100˝ – 63⁄64˝ 101˝ to 140˝ – 63⁄64˝ 141˝ to 300˝ – 63⁄64˝
301˝ to 400˝ – 63⁄64˝
401˝ to 500˝ 15mm (.5905˝)
20mm (.7874˝)
25mm (.9842˝)
30mm (1.181˝)
40mm (1.575˝)
50mm (1.968˝)
61mm (2.400˝)
Source: RMA 1P-22, 2007
Engineering Standard “Envelope Narrow V-Belts and Sheaves”
Many Goodyear Engineered Products branded V-belts are produced
to meet these standards under the Matchmaker Matching System.
Multiple V-belts will still have different lengths under this system;
however, the elongation of the polyester reinforced V-belts will
allow the belt lengths to normalize once the belts are tensioned. The
Matchmaker System only applies to V-belts with polyester cord;
V-belts with Flexten® cord do not fall into this program. Sets of
multiple Flexten reinforced V-belts have to be specially ordered to
ensure they are within an acceptable length range to each other, or
MATCHMAKER Belts
GENERAL
INFORMATION
126
• HY- T Wedge (3VX, 3V, 5VX, 5V, & 8V)
• HY-T Plus (A, B, C, & D)
• Torque Flex® (AX, BX, & CX)
• HY-T Torque Team® (HY-T & HY-T Wedge)
• Torque Team Laminated
they can be ordered as one banded HY-T® Torque Team Plus® belt.
As an example, a 5V710 belt has a Matchmaker matching limit of
0.30˝. This means a 5V710 that measures 71.150˝ is considered
matched to one that measures 70.850˝ because the difference in
belt length between the two is 71.150˝ – 70.850˝ = 0.30˝, which
is within the 0.30” matching limit that is called out for in the
Matchmaker System.
Classical Lengths
Wedge Lengths
0˝–60˝..................... 0.15˝
61˝–144˝.................. 0.30˝
145˝–240"............... 0.45˝
241˝–360"............... 0.60˝
361˝–480"............... 0.75˝
481˝ & longer......... 0.90˝
0˝–63"..................... 0.15˝
64˝–150".................. 0.30˝
151˝–250"................ 0.45˝
251˝–375"............... 0.60˝
376˝ & longer......... 0.75˝
Meets RMA Engineering Standards IP-22 for Narrow V-Belts, 2007
As a final note, the best way to optimize the Matchmaker program is
to utilize the “first in-first out” method of inventory control. Every
V-belt manufacturer that produces polyester-corded belts bases
their matching principles on the assumption that their inventory
is constantly turning over. This is because an inherent property
of polyester is that it will shrink over time. Thus, a belt built two
years ago will not measure the same as it did when it was originally
produced. How much and how fast the polyester shrinks is largely
dependent on the environmental conditions that the belt is exposed
to during storage. As it is difficult to easily monitor the environment
of certain storage spaces, it becomes apparent why it is important to
make certain that the oldest inventory is the first to be used. With
these procedures in place, the Matchmaker System will continue to
serve your multiple-belt drive needs.
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
2 0 1 0
O i l & C h e m ic a l R e s i s t a n c e
of Power Transmission Belts
In general, the presence of oil or chemicals in contact with
any belt drive system can materially affect the life span and
operational characteristics of the system. The concentration of
the chemical or oil involved, length and type of exposure, choice
of belt type used, and environmental conditions, such as heat
and humidity, all contribute to the rate and degree of effect on
the performance and deterioration.
Two effects may be noted when belts are exposed to oil and/or
chemicals. The most obvious is a swelling or increase in dimensions of the cross section so that they no longer fit the pulley
or sheave groove properly. Less apparent at casual observation,
is the deterioration of the original physical properties, which
includes adhesion between the belt components. If the degree of
swelling and/or loss of physical properties is significant, the life
of the belt will be substantially shortened.
The above effects may be brought about by a large variety of
chemicals, notably oils, acids, and solvents.
No one synthetic rubber is resistant to all of these. Some
compounds may be excellent for one chemical, but poor for
another, and only adequate for still another.
Because of this, all Goodyear Engineered Products stock belts
are constructed to be reasonably oil and chemical resistant.
The nature of the compounds and/or belt construction may
minimize swelling and deterioration. Occasional splattering by
oils and greases does not usually adversely affect standard belts.
The automotive fan belt is a typical example.
In addition, there are a great number of chemicals, such as
gasoline, which swell rubber or extract ingredients from the
belt’s rubber compounds. These may cause embrittlement,
cracking, or swelling of the belt, which results in deterioration of
performance.
If the drive is subjected to the accumulation of a considerable
amount of oil and grease on the belt, it may preclude the use
of a V-belt or a V-ribbed belt. Synchronous belts are not substantially affected by the loss of friction coefficient and may be
capable of limited operation under these conditions.
As can be seen from the above, there are many variables. However,
the following general guidelines might be of use in selecting a
belt drive system subjected to a chemical environment.
1. Prevent the accumulation of contaminants.
2. If the belts are to be subjected to only an occasional
contamination contact, a standard construction V- or
synchronous belt can be used.
3.
If the belts are expected to give long, trouble-free
operation on an industrial drive, and they are in contact
with oil or exposed to an atmosphere laden with chemicals
or solvents, consult the manufacturer for recommendations.
GENERAL
INFORMATION
Source: RMA 1P-3-2, 1999
127
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
S t a tic C o n d u cti v e B e l t s
The ordinary manifestations of static electricity are present in
everyone’s daily life: in combing one’s hair, walking across a dry
carpet, separating two sheets of paper, etc.
The specific resistivity of most rubber compounds is
approximately 1015 (10 followed by 14 zeros) ohm-cm. For all
practical purposes, it is sufficient to know that the resistivity
of rubber is very, very high and that it is a good insulator. It is
possible, however, to make a rubber compound having a
resistivity of 100 ohm-cm or less. Thus compared to ordinary
rubber compounds, these stocks may be classed as conductors.
However, when compared to copper, which has a resistivity
of 0.0000017 ohm-cm, the very best of conducting rubber
compounds, would still be classed as insulators.
The differences between a static spark and the current from a
lighting or power circuit are differences in duration, voltage,
and amperage. Usually the sparks are very short in duration
since there is no continuous source of current. The voltage of
a static spark is very high. About 20,000 volts are required to
produce a spark which will jump a one-inch gap in dry air. The
amperage and the energy, however, are usually very small.
Six mega-ohms is the maximum limit is accepted by RMA and
industry for all Static Conductive Belts. Belts produced and
designated by Veyance Technologies as static conductive meet
this RMA standard. If special customers insist on tighter static
conductive limits than required by RMA, such limits should be
carefully noted and emphasized on the order so that these belt
orders can be specially processed through the plant.
There are many ways in which static may be generated: by
friction between two unlike materials, by the breaking up of a
liquid into a spray or mist, etc.
However, merely using a conductive belt does not eliminate the
static problem entirely. The entire system must be grounded
since, if no ground is provided, the belt or other parts of the
system may by charged either by conduction or induction from
some outside source.
There is always a demand for belts and other rubber products
to be used in the presence of explosive gases, liquids, powders,
dusts, etc., where the possibility of static sparks must be kept to a
minimum.
Below, we hope to outline, in nontechnical terms, a basic overview of static conductivity.
Any material can be electrified to some extent. If the material is
a conductor, however, it may be discharged by connecting any
point with the ground. If it is a nonconductor, the charge must
be removed at the point where it is generated.
In distinguishing between conductors and insulators for static
charges, they must not be confused with the actions of similar
materials when used with ordinary electric current. The
conductivity required to dissipate a static charge is so small that
materials which are satisfactory “insulators” for ordinary electric
current may act as “conductors” for static charges.
The term “resistivity” applies to the specific resistance of the
substance of which the conductor is made. It is numerically
equal to the resistance between the opposite faces of a cube of the
substance whose edge is one centimeter. The unit of resistivity
is the Ohm-Centimeter.
GENERAL
INFORMATION
128
It is, of course, necessary to see that belt and pulley surfaces are
kept free of foreign substances, such as dirt, dust, belt dressing, etc., which are not themselves conductors. The pulleys,
of course, must be a conductive material which rules out most
nonmetallic materials unless they are specially designed and
treated.
Where the explosion hazards are severe, we strongly recommend that the user periodically check, not only the belts,
but all other possible sources of static sparks. Often the
material itself, as in the case of smokeless powder, may
be a source of static charges. Likewise, the clothes of the
operators will generate static. It is essential that all, and not just
part, of the static sources be eliminated if the danger of static
discharge is to be averted.
P O W E R
T R A N S M I S S I O N
P R O D U C T S Drive Maintenance Materials
Items:
________
________
________
________
________
________
________
________
________
TensionRite® Belt Frequency Meter
Laser Alignment Tool
Laser Alignment Tool Replacement Magnet
TensionRite Eagle Tension Tester (200 capacity with instructions)
TensionRite Eagle Tension Tester (Pencil-type with instructions)
TensionRite Large Tension Tester (Instructions included)
TensionRite Small Tension Tester (Instructions included)
TensionRite Gauges - Blue / 50 per pack for Banded Belts
TensionRite Gauges - Yellow / 25 per pack for single V-Belts
GENERAL
INFORMATION
Product Code
SAP#
2 0 1 0
Availability
62420000050000
52290800800000
62499000300000
62499000200000
52290800500000
52290800300000
70082194715000
70082194715700
20287454*
20245089*
20304774*
20039447*
20039446*
20083777*
20044882*
20140098**
20157153**
70082194707100**
70082194753100**
20044904
goodyearep.com/ptp or GBS
goodyearep.com/ptp or GBS
70082194737700**
70082194706700**
70082194717700**
70082194714800**
70082194714900**
70082194747400**
70082194747900**
70082194748300**
70082194748400**
70082194748500**
70082194753600**
20039436
20118189
20132347
goodyearep.com/ptp or GBS
goodyearep.com/ptp or GBS
GBS
goodyearep.com/ptp or GBS
GBS
goodyearep.com/ptp or GBS
goodyearep.com/ptp or GBS
goodyearep.com/ptp or GBS
goodyearep.com/ptp or GBS
goodyearep.com/ptp or GBS
goodyearep.com/ptp
goodyearep.com/ptp or GBS
goodyearep.com/ptp or GBS
70082194747500**
goodyearep.com/ptp or GBS
GBS
GBS
General Sales Materials
Product Specific:
________
________
________
PTP Full Line Product Catalog
Falcon HTC® Brochure
Synchronous Belt Flyer (Falcon HTC, Eagle NRG™ & Hawk Pd®)
________
________
________
________
________
________
________
________
________
________
________
________
Eagle NRG Brochure
Eagle Pd® Acculiner® Brochure
TensionRite Brochure
TensionRite Counter/Wall Display (Holds 50 Gauges)
ELATECH® Polyurethane Belt Catalog
ELATECH® Sales Flyer
GY Metric® Sales Flyer
Laser Alignment Tool Flyer
TensionRite Belt Frequency Meter Flyer
Full Size TensionRite Belt Frequency Meter User’s Manual
TensionRite Belt Frequency Meter Tensioning Tables
MaximizerPro™ Flyer
Market Specific:
________
ACHE (Air Cooled Heat Exchanger) Brochure
A pp l i c a t i o n
Industrial V-Belts
70082194705000
20044896
Eagle NRG Synchronous Drive Products Manual
ACHE Axial Fan Drive Systems
70082194750300
N/C
goodyearep.com/ptp
goodyearep.com/ptp
GENERAL
________
________
________
INFORMATION
Engineering Manuals:
* Contact your local Goodyear Engineered Products industrial distributor.
**EPIX users can order through GBS, otherwise, contact your local Veyance Technologies representative.
129
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
A pp l i c a t i o n Product Code
SAP#
Application/Cross Reference Materials:
________
________
________
________
________
________
________
________
________
Industrial Belt Wall Chart Product Reference — 81⁄ 2 ˝ x 11˝
Industrial Belt Wall Chart Product Reference — 113⁄ 4 ˝ x 14˝
Industrial Belt Wall Chart Product Reference — Poster size
Lawn & Garden Application Guide
Car & Light Truck Application Guide (Current to 1994)
Car & Light Truck Application Guide (1993 and prior)
Medium to Heavy Duty Truck Application Guide (Current to 1990)
Medium to Heavy Duty Truck Application Guide (1989 and prior)
Sports Vehicles (Snowmobile) Application Guide
70082194746100**
70082194701000
52098980800000
52098980600000
52098984300000
52098980700000
52098930000000
52098980900000
20044883**
20073298
20035740
20049146
20049138
20108695
20035750
Software:
________ MaximizerPro™ Drive Analysis Software Program
________ MaximizerPro Drive Data Gathering Form
Availability
goodyearep.com/ptp or GBS
GBS
GBS
www.goodyearep.com/ptp
www.goodyearep.com/ptp
Training
Product Specific:
________
________
________
V-Belt Install & Maintenance Video
Installation, Maintenance & Troubleshooting Guide
Installation, Maintenance & Troubleshooting Pre-packaged Seminar Kit
70082194729100**
70082194750600**
70082194746900**
20044937
20044945
70082194739400**
70082194739400**
62499000800000
62499000500000
62499000100000
52290800400000
52090800000000
52035980400037
52035980500037
52098981800000
52098920200000
52098920300000
20039454*
20039449*
20039445*
20044915*
20035727*
20069243*
20069265*
20073299*
20073283*
20073284*
goodyearep.com/ptp or GBS
GBS
M i s c e l l a n e o u s S a l e s S u pp l i e s & T oo l s
________
________
________
________
________
________
________
________
________
________
________
________
Power Transmission Products Store Front Banner — 5´ x 3´
Power Transmission Products Store Front Banner — 10´ x 3´
Eagle NRG™ Demo Kit
Straight Edge Pulley/Sprocket Alignment Tool Synchronous Belt Profile Gauge
“V” Profile Sheave Gauge
Automotive & FHP Belt Measuring Gauge
9209C Blank Sleeves 300 / CTN Small
9210C Blank Sleeves 500 / CTN Large
3´ Wood Wall Racks (20 boards/box)
6˝ Metal Hooks (250 hooks/box)
12˝ Metal Hooks (250 hooks/box)
GENERAL
INFORMATION
* Contact your local Goodyear Engineered Products industrial distributor.
**EPIX users can order through GBS otherwise contact your local Veyance Technologies representative.
130
GBS
GBS
P O W E R
T R A N S M I S S I O N
P R O D U C T S GENERAL
INFORMATION
2 0 1 0
WARNING
DO NOT USE THE PRODUCTS IN THIS GUIDE IN AIRCRAFT APPLICATIONS.
THE PRODUCTS IN THIS GUIDE ARE NOT INTENDED FOR USE IN AIRCRAFT
APPLICATIONS.
DO NOT USE THE PRODUCTS IN THIS GUIDE IN LIFT OR BRAKE SYSTEMS
WHICH DO NOT HAVE AN INDEPENDENT SAFETY BACKUP SYSTEM.
THE PRODUCTS IN THIS GUIDE ARE NOT INTENDED FOR USE IN LIFT
OR BRAKE SYSTEMS WHICH DO NOT HAVE AN INDEPENDENT SAFETY
BACKUP SYSTEM.
FAILURE TO FOLLOW THESE WARNINGS AND THE PROPER PROCEDURES
FOR SELECTION, INSTALLATION, CARE, MAINTENANCE, AND STORAGE
OF BELTS MAY RESULT IN THE BELT’S FAILURE TO PERFORM PROPERLY
AND MAY RESULT IN DAMAGE TO PROPERTY AND/OR SERIOUS INJURY
OR DEATH.
GENERAL
INFORMATION
The products in the Guide have been tested under controlled
laboratory conditions to meet specific test criteria. These tests are
not intended to reflect performance of the product or any other
material in any specific application, but are intended to provide
the user with application guidelines. The products are intended
for use by knowledgeable persons having the technical skills
necessary to evaluate their suitability for specific applications.
Goodyear assumes no responsibility for the accuracy of this
information under varied conditions found in field use. The user
has responsibility for exercising care in the use of these products.
131
P O W E R
T R A N S M I S S I O N
notes
GENERAL
INFORMATION
132
P R O D U C T S GENERAL
INFORMATION
P O W E R
T R A N S M I S S I O N
notes
P R O D U C T S N O T E S
2 0 1 0
P O W E R
T R A N S M I S S I O N
P R O D U C T S
2 0 1 0
U . S . A .
1 - 8 0 0 - 2 3 5 - 4 6 3 2
FA X 1 - 8 0 0 - 7 6 2 - 4 0 1 7
G O O D Y E A R E P. C O M / P T P
The GOODYEAR (and Winged Foot Design) trademark is used by Veyance Technologies, Inc. under license from The Goodyear Tire & Rubber Company. Goodyear Engineered Products are manufactured and sourced exclusively by Veyance Technologies, Inc. or
its affiliates. The following trademarks are licensed to Veyance Technologies, Inc. by The Goodyear Tire & Rubber Company, including Compass, Eagle NRG, Eagle Pd, Flexten, Gatorback and GY Metric. ©2010 Veyance Technologies, Inc. All Rights Reserved.
700-821-947-071
goodyearep.com
Aftermarket Parts - Automotive, Conveyor Belt - Heavyweight and Lightweight,
Government, Heavy Duty, Home and Garden, Hydraulics, Industrial Hose,
Power Transmission Products, Powersports, Rubber Track,
Seawing Offshore Oil Hose
09GPTP023-2/10