Download Describe of using signaling

www.portalpmr.com
How to use programming software
1. When you open programming software, you can’t use the programming software, as
show in following chart:
2. When you have our product, only use programming cable to contact transceiver with
computer, programming software will auto contact with transceiver, as show in following
chart:
www.portalpmr.com
Note: The interface of programming cable should be the same as programming software.
FM-channel
1. FM channel code: Corresponding with sixteen channel codes.
2. Rx frequency：Edit according to the local radio frequency, the range is: 87-108MHz.
3. Name of transmitter-receiver: You can edit name of radio frequency which you have set,
it can make up with 26 letter ( A-Z), ten number (0-9)，the length of transceiver-receiver
name at most 6 bits.
Edit channel (only react on channel mode)
1. All kind of 0-199 channel information will be show in form.
1) RX frequency： selective range：According to model
2) TX frequency: selective range：According to model
２. CTCSS/DCS encoding and decoding
1) CTCSS
Function: CTCSS tone
Option：67.0－254.1 Hz
2) DCS
Function: DCS tone
Option：000－754
Note: D×××N means normally DCS tone, D×××I means reverse DCS tone, you can put off CTCSS and
DCS in each channel, select from list.
3. Transmit power
Function: Select transmit power
Option: High（4W）/ Low（1W）
，1-5 means low power, 6-10 means high power
Default：10
4. Channel bandwidth
Function: Set frequency working bandwidth
Option:12.5KHZ （narrow）/ 25KHZ（wide）
Default: 25KHZ
5. PTT-ID
PTT ID: Select way of transmit PTT ID（BOT/EOT/BOTH）
。
www.portalpmr.com
Option: BOT/EOT/BOTH
1) BOT: When press [PTT], transceiver will transmits ID code at the beginning of transmitting.
2) EOT: When release [PTT], transceiver will transmits ID code at the end of transmitting.
3) BOTH: Transceiver will transmit ID code at the beginning or at the end.
Default: OFF
6. Optional signaling
Function: Select signaling mode
Option: WDTS/DTMF / 2TONE / 5TONE
Default: WDTS
7. Mutemode
Function: Mutemode means the way of open speaker
Option: QT/AND/OR
1) QT: When transceiver receives a signaling which can open squeal or suited sub-tone, then it
will open speaker. If transceiver doesn’t set sub-tone, it only needs to receive a signaling which can open
squeal that also can open the speaker.
2) AND: When transceiver receives the signaling of QT and has suited signal order, then it will open
speaker.
3) OR: When transceiver receives one signaling suited QT or AND, it will open the speaker.
Default: QT
8. Busy channel lockout
Function: After switch on this function, it can prevent to disturb other transceivers which are
communicating, if the channel which you have set has been used by other transceiver, then you could not
transmit, when press [PTT].
Option: ON/OFF
Default: OFF
9. Voice encrypt compress
Function: Using voice encrypt compress, when on communication it can reduce noise, make the voice
more clear.
Option: ON/OFF
Default: OFF
10. Add scanning
Function: This function means whether ensure to add the frequency of stored channel to scanning list or
not;
Option: ON/OFF
Default: ON
11. Scrambler
Function: Means encrypt communication, using scrambler, it can avoid other transceivers which do not
use scrambler to hear clear what you talk, but at the same time you also could not hear clear
other’s which do
not use scrambler.
Option: ON/OFF
Default: OFF
12. Signaling information
Function: This function is destined for signaling code of which edit signaling.
www.portalpmr.com
Option: 1~15
Default: 1
13. Channel name
Function: Edit channel name.
Option: Can make up of 26 letters （A~Z, ten number（0~9）.
Default: Blank
Optional parameter
only react on frequency mode
1. Transmit over timer
Function: The TOT is designed for to prevent your radio to continual transmit too a long time, when
transceiver is exceeding the preset time limited, it will stops transmit and give you a prompt voice.
Option: 15~600 seconds
Default: 60 seconds
2. Transmit overtime alarm
Function: Transmit overtime alarm is set for the user that when he/she will reach the time set of TOT, then
give a voiceprompt and light will flicker during transmit.
Option: OFF/1~10
Default: 5
3．Squelch level
Function: Set squelch level is that keeps the speaker silent when there is no signaling. When the squelch
level is set all right, then you will hear voice only transceiver receives signaling. If the
squelch level set too high, then the signaling should be strong enough that transceiver
can receive.
Option: 0~9
Default: 5
4. Voice guide
Function: Select kind of voice guide.
Option: English/ Chinese/OFF
Default: English
5. Power on display
Function: Select the display of power on
Option: Full display/Welcome/Voltage
Default: Full display
www.portalpmr.com
The following chart only react A segment on frequency mode
Shift direction
Function: Select receive frequency is higher (+) or lower (-) than transmit frequency
Option: OFF/+/Default: OFF
Offestfrequency
Function: Offsetfrequency is dispersion frequency between receive and transmit
Option: 0~99.950MHz
Default: 0.6MHz
The following chart only react B segment on frequency mode
www.portalpmr.com
Currently working mode
Frequency/channel: Means when you have finished set transceiver, when restart transceiver, to work on
frequency mode or channel model.
Channel number: Means edit the number of this transceiver channels.
Channel mode
Setting MENU: Means whether turn on MENU function or not on channel mode.
Reset: Means whether turn on reset function on channel mode.
Synchronous display: Means whether display A/B segment at the same time.
DTMF sidetone
Function: Means whether turn on speaker or not when transmit DTMF sidetone, and hear a suited DTMF
sidetone from speaker.
Option:
KEY：Switch on sidekey tone, when transmit.
ANI：Switch on ANI ID sidetone, when transmit.
BOTH：Switch on sidekey tone and ANI ID sidetone, when transmit.
OFF：Turn off all
Default: KEY
VOX
Function: When check a voice, switch to transmit mode.
Option: OFF/1~10
Default: OFF
www.portalpmr.com
Auto backlight
Function: The time of turn on backlight
Option: OFF/1~5
Default: 3
Ring mode
Function: After transceiver receives a suited signaling, it will give a voice prompt
Option: SOUND：Switch on ring time
BIV：Switch on libration
BOTH：Switch on both ring and libration
OFF：Turn off all
Default: SOUND
Ring time
Function: When it exceeding to the preset value of ring time, speaker will turn on.
Option”0~10
Default: 5
Scan mode
Function: Transceiver will stop scan when detects a signaling frequency or stored channel. According to
you select restart, transceiver will go on scan or stop scan.
Option:
TO：After signal on channel disappears, the transceiver will start scanning if you do not have any
operation within 5 seconds
CO：Transceiver will stop scan when searches a signaling, it will go on scanning after signal disappears 3
seconds
SE：Scanning will stop when receives a signal
Default：TO
Delay VOX
Function： The purpose of setting VOX delay time is made transceiver return to RX mode after calling,
whether the last part of calling can be transmit or not, in order to avoid this problem, then you can set a
propriety delay time, make calling can be transmitted completive. But be care, do not set delay time too a
long time.
Option:0~20 ms
Default: 15 ms
Beep prompt
Function: Beep prompt is to tell you whether transceiver is run well or run wrong or has an malfunction.
We kindly advice you to switch on this function
www.portalpmr.com
Option: ON/OFF
Default: ON
Keyboard lock/auto lock
Function: Lock keyboard
Option: ON/OFF
Default: OFF
Busy channel lockout
Function: After switch on this function, it can prevent to disturb other transceivers which are
communicating, if the channel which you have set has been used by other transceiver, then
you could not transmit, when press [PTT].
Option: ON/OFF
Default: OFF
Savemode
Function: This function will turn off RX circuit for a minute (can set), then after a minute it will turn on and
detect signaling.
Option: OFF1:1/1:2/1:3/1:4（Means the impulse of turn on and turn off of RX）
Default: 1:2
Delay transmit ID
Function: If repeater does not respond to the ID which transmit from transceiver, then you can adjust this
parameter.
Option:: 0~2000 ms
Default: 600 ms
Switch on frequency modulation radio
Function: Defined whether switch on radio
Option: ON/OFF
Default: ON
Defined sidekey
Function: Set function of sidekey
1.
FM：FM radio function key
2.
CALL：Currently signaling calling key
www.portalpmr.com
3.
NO-SUB：Cancel receiving CTCSS/DCS signaling
4.
JP-PRI：Switch to priority channel scan
5.
JP-EMC：Switch to alarm channel
>>When FM radio on working, and currently frequency or channel still on standby, if receives a signaling,
it will auto switch to transceiver. After signaling disappears 5 seconds, it will auto back to FM radio, if
you want to exit FM, please press sidekey 1again.
>>You can edit FM radio channel by programming software, make the FM radio display FM frequency
and name, When you have successful edited, press sidekey to switch on FM radio, then you can use
the channel knob to switch FM radio, or use the UP or DOWN to switch. If the model doesn’t have
channel knob, you can use the UP or DOWN to switch.
Defined topkey
Function: Set function of topkey
1.
EMCALL: Turn on alarm function
2.
CALL01-CALL15: Signaling calling
Defined MoNI key
Function: Defined for turn on squelch circuit.
1.
CONTIN: Do keep press sidekey 2, then turn off squelch circuit.
2.
PRESS：Press sidekey 2 one time, then turn off squelch circuit.
Standby display color
Function: Defined for transceiver backlight on standby.
Option: Purple/Blue/Orange
Default: Purple
Receive display color
Function: Defined for transceiver backlight on receiving.
Option: Purple/ Blue/Orange
Default: Blue
Transmit display color
Function: Defined for transceiver backlight on transmitting.
Option: Purple/Blue/Orange
Default: Orange
Switching mode password
Function: Means that whether set password to switch between frequency mode and channel mode.
Option: 0~9
Default: 000000
Set working range password
Function: Limited transceiver working range
Option: 0~9
www.portalpmr.com
ANI ID code
Function: Use to send information to receiver, when alarm, allcall, groupcall or selectcall.
Option: 0~9
Default: 80386
NOTE
>>Due to ANI ID code of this transceiver has difference of 3 bits, 4 bits and 5 bits, so using any one of
transceivers in group should be set the same.
Length of code
Function: Edit bit of ANI ID code
Option: 3~5
Default: 5
This transceiver using level
Function: Means currently transceiver the right of using range
Option: Normally use/Forbid transmitting/ Forbid transmitting and receiving
Default: Normally use
Monitor priority channel
Function: Whether switch on priority scan
Option: ON/OFF
Default: OFF
NOTE
>>This transceiver priority channel scan can selectable from 0-199.
>>There is only display an “S” on LCD screen, that means transceiver has started priority channel scan.
>>Start priority channel scan needs two condition: 1）Do priority channel scan switch on.
2）This function only scan channels which has been stored.
>>On frequencmode, channelmode or on scanning, when transceiver detects signaling on priority
channel scan, it will transfer the priority channel, if you don’t do any operation after signaling
disappears 3 seconds, transceiver will back to primary frequency and resume priority scan.
>>The speed of start or resume priority scan, is relate with the time of setting auto backlight. When the
time of auto backlight be set as “1”, the speed of start or resume priority scan will be the fastest.
>>When priority channel scan which has been set parameter receives signaling, then only the suited
frequency, transceiver can transfer priority channel.
www.portalpmr.com
>>The transferred priority channel only can be used communication, you can’t do any other operation
until resume primary frequency.
Emergency calling type
Function: Means the type of emergency calling
Option：
ALARM：Field alarm
ENI：Distant alarm
BOTH：Field + distant alarm
Default: BOTH
NOTE
>>On frequencymode/channelmode, only type of emergency calling be set as ENI and BOTH, then can
use the alarm channel to alarm.
>>On frequencymode/channelmod, if you don’t set alarm channel, then it will alarm at present channel or
frequency
Alarm channel
Function: Select one of channel which has been edited to emergency alarm.
Option: CH-000~CH199
Default: CH000
Switch on dual-standby
Function: Means whether to make A/B segment standby at the same time.
Option: ON/OFF
Default: ON
Select type of transmit after switch on dual-standby
Function: When switch on dual-standby, select to transmit on A segment or on B segment.
Option: A segment/B segment
Default: A segment
Describe of using signaling
Allcall, groupcall, selectcall
This transceiver has function of transmit ANI ID code, edit ANI ID code and DTMF
decoding, When without other communication equipment, it can accomplish the operation
of allcall, groupcall and selectcall.
How to use allcall, groupcall and selectcall
1. Edit ANI ID code
NOTE: Using any one of transceivers in group should edit difference ANI ID code.
ANI ID code: ANI—XXX
ANI—XXXX
ANI—XXXXX（total has three methods）
www.portalpmr.com
XXX：Means can edit 3 bits ANI ID code
XXXX：Means can edit 4bits ANI ID code
XXXXX：Means can edit 5 bits ANI ID code
X
XXXX
Group list
A unique ANI ID code
0~9 groups
From 0000 to 9999 maximum
This is how build up ANI
The details of edit method see user’s manual ANI code edit.
2. Setting allcall, groupcall and selectcall
NOTE: Using any one of transceiver in group should be set WDTS optional signaling.
Setting WDTS optional signaling, the details see user’s manual setting optional
signal.
3. Mutemode should be set as AND. The details of method see user’s manual
setting mutemode.
4. Press PTT to transmit, according to you need, you can set time one of the
BOT/EOT/BOTH, the details see user’s manual MENU 25
5. Turn on ring time alarm and set ring time (according need). The details of
method see user’s manual: MENU 30 and MENU 31.
6. Setting PTT-LT: According to present condition, set delay time of transmit
code, the details see user’s manual MENU 26
NOTE
>>Using any one of transceiver in group, the frequency or channel must be set the same.
A. Using allcall：
Press [PTT] to transmit, after transmitting ANI ID code, input
SCAN
+
directly
#
by keyboard.
B. Using groupcall：
Press [PTT] to transmit, after transmitting ANI ID code, input [ group No. ] +
SCAN
+
SCAN
directly by keyboard.
C. Using selectcall：
Press [PTT] to transmit, after transmitting ANI ID code, input ANI ID code you want to
call directly from keyboard.
NOTE
>>This transceiver has memory function, after you used allcall, groupcall, and selectcall, then you want to
transmit again, the ID code is the same as last time you transmitted. If you want to transmit new ID
code, please press
before transmitting.
>>This transceiver has difference of 3 bits, 4bits and 5bits, so all transceiver’s ANI ID code in group has
www.portalpmr.com
T
I
X
E
DTMF、2TONE、5TONE
SCAN
1. When DTMF/2TONE/5TONE is set as one frequency, then press PTT to transmit
DTMF/2TONE/5TONE.
2. When one channel has been set DTMF/2TONE/5TONE, the preset function will act
only transceiver receives a matching DTMF/2TONE/5TONE signaling.
3. Setting signaling
1) NOTE: Using any one of transceivers in group should be set DTMF/2TONE/5TONE
optional signaling, the details of setting optional signaling see user’s manual MENU 23.
2) Setting sidetone: The details see user’s manual MENU 16, according to you need to
select.
3) Mutemode should be set as AND, the details of method see user’s manual MENU 24.
4) Setting PTT: Depend on your requirement to select one of BOT/EOT/BOTH, see user’s
manual MENU 25.
5) Setting S-INFO: The information of receiver and transmitter should be set the same.
6) Setting PTT-LT: according to present condition, set delay time of transmit code, the
details see user’s manual MENU 26.
Describe of setting 2tone:
www.portalpmr.com
Encoding
Information code
Function: Edit serial number of transmit ID code.
Option: 1~15
First frequency
Function: 2-tone has fifteen serial number, edit first frequency of transmit ID code
Option: 300Hz~3000Hz
Second frequency
Function: 2-tone has fifteen serial number, edit second frequency of transmit ID code
Option: 300Hz~3000Hz
The time of transmit first frequency
Function: The time of transmit first tone of 2tone.
Option: 0~1000 ms
Default: 600 ms
The time of transmit second frequency
Function: The time of transmit second tone of 2tone
Option: 0~1000 ms
Default: 600 ms
The time between 2 frequencies
Function: The time between first tone and second tone of the 2tone.
Option: 0~1000 ms
Default: 600 ms
www.portalpmr.com
Decoding
Decoding（There are the same of Decoding 1、Decoding 2、Decoding 3、Decoding 4）
The way make up of 2tone:
There has twelve methods to make up of 2tone: A-B/ A-C/ A-D/ B-A/ B-C/ B-D/ C-A/ C-B/C-D/ D-A/ D-B/
D-C/
The way of respond to decoding 2tone:
When
you
have
succeed
of
decoding
Prompt/Revert/Prompt and revert.
A tone[Hz]: Select range: 300~3000 Hz
B tone [Hz]: Select range: 300~3000 Hz
C tone [Hz]: Select range: 300~3000 Hz
D tone [Hz]: Select range: 300~3000 Hz
Reset time [ms]: 100~8000ms
2tone,
there
has
4
ways
to
respond:
Nothing/
www.portalpmr.com
Standard
Standard frequency of 5tone (5-TONE)
This transceiver has fifteen 5tone international standard can be selectable: CCIR1、CCIR2、PCCIR、
ZVEI1、ZVEI2、ZVEI3、 PZVEI、DZVEI、PDZVEI、EEA、EIA、EURO、CCITT、NATEL、MODAT
Standard name
You can view the corresponding tone of fifteen 5 tone international standard, as show in following chart
www.portalpmr.com
Encoding
Information code
Function: Edit serial number of transmit ID code.
Option: 1~15
First frame encoding（there are the same encoding of first frame, second frame and third frame）
Function: Edit transmitting ID code
Option: 0~9
Using standard
Each information code has sixteen standard encoding can be selectable.
Option: ZVEI1, ZVEI2, ZVEI3, PZVEI, DZVEI, PDZVEI, CCIR1, CCIR2, PCCIR, EEA, EUROSIGNAL,
NATEL, EIA, MODAT, CCITT, USER DEFINED
Default: CCIR1
NOTE: The standard of encoding and decoding, information code and information encoding should be
the same, then you can decode.
Delay time before transmit first code: The delay time of transmit first frame 5tone, during this time it only
allows carrier wave signaling.
Option: 0－1000 ms
Default: 400 ms
Delay time before transmit second code: The delay time of transmit second frame 5tone,
during this time it only allows carrier wave signaling
www.portalpmr.com
Option: 0－1000 ms
Default: 200 ms
Delay time before transmit third code:
The delay time of transmit third frame 5tone, during
this time it only allows carrier wave signaling
Option: 0－1000 ms
Default: 200 ms
Expand time of first tone in each group code: The time of transmit first tone of each frame.
Option: 0－1000 ms
Decoding
Information code
Function: Edit serial number of transmit ID code
Option: 1~15
Using standard
Each information code has sixteen standard decoding can be selectable.
Option: ZVEI1, ZVEI2, ZVEI3, PZVEI, DZVEI, PDZVEI, CCIR1, CCIR2, PCCIR, EEA, EUROSIGNAL,
NATEL, EIA, MODAT, CCITT, USER DEFINED
Default: CCIR1
First frame decoding（there are the same of first frame, second frame and third frame）
Function: Edit transmitting ID code
www.portalpmr.com
Option: 0~9
Function:
Option:
1.
2.
3.
4.
5.
6.
7.
Call: Receiving matching 5tone, turn on squelch to communicate
Monitor: Receiving matching 5tone, auto transmitting.
Inspection: Receiving matching 5tone, reply transmitter.
Emergency: Receiving matching 5tone, turn on alarm function.
Stun: Receiving matching 5tone, couldn’t transmit.
Kill: Receiving matching 5tone, could not receive and transmit.
Revise: Receiving matching 5tone, revive the stunned or killed transceiver.