Download HSP50214BVC
Transcript
HSP50214B One caveat to selecting the FIR outputs to be routed directly to the coordinate converter is that because the I/Q samples for the coordinate conversion are chosen from before the resampler, the magnitude and phase samples will not align with the I/Q samples, if the resampler or interpolation halfband filters are used. This optional signal routing mode was intended for FM or for burst PSK where a fixed decimation can be used. It is also applicable when resampling or timing adjustments on the demodulated samples are done in a processor following PDC. The magnitude resolution may suffer because there is no gain adjustment before computing the magnitude. If the signal is < - 90dBFS, it will be below the LSB of the magnitude output. where D is the discriminator delay defined in Equation 21 (1 < D < 8), fSAMPOUT is the Discriminator FIR filter output sample rate and CW is the desired center frequency. When the phase multiplier is set to a value other than 20, the discriminator range is reduced proportionally. The phase multiplier can be 1, 2, 4 or 8 (20 to 23). Thus, a multiply of 21 reduces the range by 2, a multiply of 22 reduces the range by 4, and a multiply of 23 reduces the range by 8. The FIR filter can be configured with up to 63 symmetric taps and up to 32 asymmetric taps. In the symmetric mode, the FIR can be configured for even or odd symmetry, as well as with an even or odd number of filter taps. Decimation is provided to allow more processing time for longer (i.e., more taps) filter structures. PHASE INPUT The enable signal for gating data into the coordinate converter is either the AGC data ready signal or the resampler data ready signal. If the resampler is bypassed, the AGC data ready signal is used and there is a delay of 6 clock cycles between the FIR data being ready and the coordinate converter block sampling it. If the resampler is enabled, its data ready signal will be delayed by 6 clocks (for the AGC) plus the compute delay of the resampler block. This may cause the I/Q to |r|/θ output sample alignment to shift with decimation. For this reason, it is recommended that the resampler/halfband filter block be bypassed when using this new data path. To select the output of the 255 tap programmable FIR filter to be routed to the coordinate converter, set Control Word 27, Bit 13 to a logic one. For routing as in the HSP50214, set Control Word 27, Bit 13 to a logic zero. PHASE MULTIPLIER † DISCRIMINATOR DELAY DISCRIMINATOR EN † † DELAY (1-8) + FIR COEFFICIENTS DISC. FIR DECIMATION FIR SYMMETRY TYPE FIR SYMMETRY FIR TAPS † † † † † + 63-TAP FIR FILTER FREQ(15:0) (2’s COMPLEMENT) † Controlled via microprocessor interface. FIGURE 29. FREQUENCY DISCRIMINATOR BLOCK DIAGRAM Frequency Discriminator The discriminator block delays phase from the Cartesian to Polar Section and subtracts it from the latest sample. This delay and subtract can be modeled as a programmable delay comb filter. The output of the filter is dθ/dt, or frequency. The transfer function of the discriminator is set by H(z)= 1 – Z –D (EQ. 21) where D is the programmable discriminator delay expressed in number of sample clock delays. The discriminator output frequency is then filtered with a programmable FIR filter. The Block Diagram of the Frequency Discriminator is shown in Figure 29. The range of delay in the discriminator is from 1 to 8 samples. Modulo 2π subtraction eliminates rollover problems in the subtraction at 2π. The alias free discriminator frequency range is given by: Range FREQDISC = CW ± FSAMPOUT ⁄ ( D + 1 ) ; 31 (EQ. 22) The HSP50214B offers an expanded choice of signals to be filtered by the discriminator FIR. The choices are: 1) 18-bits of delayed, and subtracted (and optionally shifted) phase. This is the Discriminator FIR filter input found in the HSP50214. 2) 18-bits of magnitude from the coordinate converter block. This was added to provide for post-detection filtering of AM signals. 3) 18-bits from the I output of the resampler/interpolation halfband filter block. This was added to provide for processing of SSB signals. The shift, delay, and subtract functions are bypassed for items (2) and (3). In addition to the FIR input selections, the Q input to the coordinate converter block can be zeroed so that the magnitude output is the magnitude of I only. Again this was added to provide for processing SSB signals. FN4450.4 May 1, 2007