Download Reference Manual - Krypto Security

Special Opening: A Special Opening Reporting Code will be
transmitted if the Partition(s) is disarmed using any of the following methods:
• Disarming using the Maintenance Code
• Disarming via the DLS Software
• Disarming via keyswitch
[345] - Maintenance Alarm Reporting Codes
Battery Trouble Alarm: the panel will transmit a Battery
Trouble Alarm Reporting Code when the backup battery
drops below 11.5 VDC.
AC Failure Trouble Alarm: the panel will transmit an AC Failure Trouble Alarm Reporting Code when the AC to the panel
is lost and the AC Failure Communication Delay timer
expires.
Bell Circuit Trouble Alarm: a Bell Circuit Trouble Alarm
Reporting Code will be transmitted immediately if an open
condition is measured on the Bell Output of the main panel.
Fire Trouble Alarm: a Fire Trouble Alarm Reporting Code
will be transmitted immediately when an open condition is
measured on any Fire type zone.
Auxiliary Power Supply Trouble Alarm: the Auxiliary Power
Supply Trouble Alarm Reporting Code will be transmitted if
the AUX output is shorted.
TLM Trouble: a TLM Trouble Reporting Code can only be
transmitted if an alternate communicator is being used. The
panel will only transmit the signal after the time programmed
for the TLM Trouble Delay.
General System Trouble: a General System Trouble Reporting Code will be transmitted if the panel detects any of the
following:
• AC Power Failure
• Low Battery
• AUX Output Trouble
• Output #1 on the PC5200/PC5204 Power Supply/Output
Module.
• T-Link Troubles
General System Supervisory Trouble: a General System
Supervisory Trouble Reporting Code will be transmitted if
any module goes missing from the Keybus. If the module is a
zone expander the panel will also transmit the Zone
Expander Supervisory Alarm Trouble Reporting Code.
[346] - Maintenance Alarm Reporting Codes
Battery Trouble Restoral: the Battery Trouble Restoral
Reporting Code will not be transmitted until the battery has
been charged over 12.5 VDC.
AC Failure Trouble Restoral: the AC Failure Trouble Restoral Reporting Code will be transmitted once AC power has
been restored for the amount of time programmed for AC
Failure Communication delays.
Bell Circuit Trouble Restoral: the Bell Circuit Trouble
Restoral Reporting Code will be transmitted as soon as the
open condition on the bell output is corrected.
Fire Trouble Restoral: the Fire Trouble Restoral Reporting
Code will be transmitted when the correct resistance value is
measured on any Fire type zone.
Auxiliary Power Supply Trouble Restoral: the panel constantly checks the AUX output, when the excessive current
draw is removed the panel will reset the output and transmit
an Auxiliary Power Supply Trouble Restoral Reporting Code.
TLM Restoral: the TLM Restoral Reporting Code will be
transmitted immediately after the trouble is restored.
General System Trouble Restoral: a General System Trouble Restoral Reporting Code will be transmitted when the
panel detects none of the following:
• AC Power Failure
• Low Battery
• AUX Output Trouble
zone. A different reporting code can be programmed for
each zone for identification.
[334]-[337] - Tamper Reporting Codes, Zones 1 to 64
The Zone Tamper Restoral Reporting Code will be transmitted immediately when the tamper condition is restored.
[338] - Miscellaneous Tamper Reporting Codes
General System Tamper: a General System Tamper Reporting
Code will be transmitted when the tamper zone on any module is violated.
General System Tamper Restoral: the General System
Tamper Restoral Reporting Code will be transmitted when
the tamper zone on the module is restored.
Keypad Lockout: the panel will transmit the Keypad Lockout Reporting Code if the lockout is activated.
[339]-[340] - Closing (Arming) Reporting Codes, Zones
1-32
The panel will transmit a Closing Reporting Code to indicate
a Partition(s) is armed. A different reporting code can be
transmitted for each User Code, Partition Master Code and
System Master Code to identify who armed the partition(s).
[341] - Miscellaneous Closing (Arming) Reporting Codes
Closing by Duress Code 33/34: a closing by Duress Code
Reporting Code will be transmitted in addition to the Duress
reporting code if a Partition(s) is armed using a Duress Code
Closing by Master or Supervisory Code: the panel will transmit a Closing Reporting Code to indicate a Partition(s) is
armed. A different reporting code can be transmitted for
each User Code, Supervisory Code and System Master
Code to identify who armed the Partition(s).
Partial Closing: a Partial Closing Reporting Code will be
transmitted if a Partition is armed with zones manually
bypassed. The code will also be transmitted if a Partition
Auto Arms with zone(s) in violation.
Special Closing: a Special Closing Reporting Code will be
transmitted if the Partition(s) is armed using any of the following methods:
• Quick Arm
• Auto Arm
• Arming via the DLS Software
• Arming via Keyswitch
• Away Function Key Arming
• Arming with the Maintenance Code
• Stay Function Key arming
Late to Close: a Late to Close Reporting Code will be transmitted if a partition isn't armed before the Auto-arm start time
when the late to close option, (Section 017, option 5) is
enabled.
[342]-[343] - Opening (Disarming) Reporting Codes
Access Codes 1 to 32
The panel will transmit an Opening Reporting Code to indicate partition(s) is disarmed. A different reporting code can
be transmitted for each user code, partition master code and
system master code to identify who armed the partition(s).
[344] - Miscellaneous Opening (Disarming) Reporting
Codes
Opening by Duress Code 33/34: This Reporting Code will
be transmitted in addition to the duress reporting code if a
Partition(s) is disarmed using a Duress Code
Opening by Master or Supervisory Code: The panel will
transmit this reporting code to indicate a Partition(s) is armed.
A different reporting code can be transmitted for each User
Code, Supervisory Code and System Master Code to identify
who armed the Partition(s).
Auto Arm Cancellation: This reporting code is transmitted
when the Auto Arming sequence is canceled or Postponed
37