Download View - Microh

1.Open the box and checking
Congratulations on choosing our products! Please carefully read this instruction manual in its
entirety and keep it well for using reference. This manual contained about the installation and the
relative using information of this products. Please according to this manual's relative speaking when
using this equipment.
This equipment was made of new style, high intensity plastic and cast aluminium. It fully
shows the modem times light characteristic with beauty structure. And it was made according to CE
standard. Fully up the international standard of DMX512 agreement. Master or slave in phase
control. Can be use in large entertainment, theater, performing and playing hall, etc.
This product uses MSR 575/2 electrical arc lamp. When receiving this product please carefully
bring and put; and check that whether this equipment has been damaged or not during transportation.
And please also check the following thing was enclosed:
Signal line ----------------------- one piece Safety string -----------------------one piece
User Manual-----------------------one set
2. Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualilfied
- follow the instructions of this manual
CAUTION:
Ø
Ø
Ø
Ø
Ø
Ø
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
Be careful with your operations.
With a high voltage you can suffer a dangerous electric shock when touching the
wires!
Ø This device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes writtenin this manual.
Important:
Ø T he manufacturer will not accept liability for any resulting damages caused by the nonobservance of this manual or any unauthorized modification to the device.
Ø Please consider that damages caused by manual modifications to the device are not
subject to warranty.
Ø Never let the power-cord come into contact with other cables! Handle the power-cord
and all connections with the mains with particular caution!
Ø Make sure that the available voltage is not higher than stated on the rear panel.
Ø Always plug in the power plug least. Make sure that the power-switch is set to OFFposition before you connect the device to the mains. The power-plug has to be
accessable after installing the device.
Ø Make sure that the power-cord is never crimped or damaged by sharp edges. Check the
device and the powercord from time to time.
1
Ø by the plug. Never pull out the plug by tugging the power-cord.
Ø This device falls under protection class I. Therefore it is essential to connect the
yellow/green conductor to earth.
Ø The electric connection, repairs and servicing must be carried out by a qualified
employee.
Ø Do not connect this device to a dimmer pack.
Ø Do not switch the fixture on and off in short intervals as this would reduce the lamp s
life.
Ø During the initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective.
Ø Do not touch the device s housing bare hands during its operation (housing becomes hot)!
Ø For replacement use lamps and fuses of same type and rating only.
CAUTION :
EYE DAMAGES !
Avoid looking directly into the light source(meant especially for epileptics) !
3. Operating determinations
Ø This device is a moving-head spot for creating decorative effects and was designed for
indoor use only.
Ø If the device has been exposed to drastic temperature fluctuation (e.g. After transportation), do not switch it on immediately. The arising condensation water might damage
your device. Leave the device switched off until it has reached room temperature.
Ø Never run the device without lamp!
Ø Do not shake the device. Avoid brute force when installing or operating the device.
Ø Never lift the fixture by holding it at the projector-head, as the mechanics may be
damaged. Always hold thefixture at the transport handles.
Ø When choosing the installation-spot, please make sure that the device is not exposed to
extreme heat, moistureor dust.There should not be any cables lying around. You
endanger your own and the safety of others!
Ø The minimum distance between light-output and the illuminated surface must be more
than 2 meters.
Ø Make sure that the area below the installation place is blocked when rigging, derigging
or servicing the fixture.Always fix the fixture with an appropriate safety-rope. Fix the
safety-rope at the correct holes only.
Ø Only operate the fixture after having checked that the housing is firmly closed and all
screws are tightly fastened.
Ø The lamp must never be ignited if the objective-lens or any housing-cover is open, as
discharge lamps mayexplose and emit a high ultraviolet radiation, which may cause
burns.
Ø The maximum ambient temperature ta = 40 must never be exceeded. Otherwise, the
lamp is switched off andthe fixture is out of operation for 5 minutes..
2
4.Description of the device
1 - Moving head
2 - Yoke
3- Carry handles
4 - Base
1
2
4
3
5
Serial number:
Rear panel:
5 -Power switch
6 -DMX output
7- DMX input
8- Power cord
9- Fuse holder
POWER
LIGHTING CONTROL PROTOCOL:DMX512
SERIAL DATA LINK
OUT DMX
IN
LAMP:
MSR 575/2
POWER SUPPLY
9
FUSE 10A
1=GND
2=SIG.3=SIG.+
8
6
7
14
Front panel:
10 - Mode-button
11 - Enter-button
12 - Up-button
13- Down-button
14 - Display
10
11 12
13
3
5.3 Inserting/Exchanging gobos
DANGER:Install the gobos with the device switched off only. Unplug from mains before!
If you wish to use other forms and patterns as the standard-gobos, or if gobos are to be
exchanged, open the topcover of the head by loosening 2 screws on the top cover. Remove
the fixation ring with an appropriate tool. Remove the gobo and insert the new gobo. Press
the fixation ring together and insert it in the front of the gobo.
CAUTION:Never unscrew the screws of the rotating goboas the ball bearing will
otherwise be opened!
° × ¹ â
5.4 Rigging the fixture
DANGER TO LIFE:Please consider the respective national norms during the
installation!The installation must only be carried out by an authorized dealer!
Ø The installation of the projector has to be built and constructed in a way that it can hold 10
times the weight for 1 hour without any harming deformation.
Ø The installation must always be secured with a secondary safety attachment, e.g. an
appropriate catch net. This secondary safety attachment must be constructed in a way that
no part of the installation can fall down if the main attachment fails.
Ø When rigging, derigging or servicing the fixture staying in the area below the installation
place, on bridges, under high working places and other endangered areas is forbidden.
Ø The operator has to make sure that safety-relating and machine-technical installations are
approved by an expert before taking into operation for the first time and after changes
before taking into operation another time.
Ø The operator has to make sure that safety-relating and machine-technical installations are
approved by an expert after every four year in the course of an acceptance test.
Ø The operator has to make sure that safety-relating and machine-technical installations are
approved by a skilled person once a year.
Ø The projector should be installed outside areas where persons may walk by or be seated.
Ø IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE,
including (but not limited to)calculating working load limits, installation material being
used, and periodic safety inspection of all installationmaterial and the projector. If you
lack these qualifications, do not attempt the installation yourself, but instead use a
professional structural rigger. Improper installation can result in bodily injury and or
damage to property.
Ø The projector has to be installed out of the reach of people.
Ø If the projector shall be lowered from the ceiling or high joists, professional trussing
systems have to be used. The projector must never be fixed swinging freely in the room.
Ø Caution: Projectors may cause severe injuries when crashing down! If you have doubts
concerning the safety of a possible installation, do NOT install the projector!
Ø Before rigging make sure that the installation area can hold a minimum point load of 10
times the projector s weight.
5
Ø The projector can be placed directly on the stage floor or rigged in any orientation on a
truss without altering its operation characteristics.
Ø For overhead use, always install a safety-rope that can hold at least 10 times the weight of
the fixture. You must only use safety-ropes with screw-on carabines. Pull the safety-rope
through the two apertures on the bottom of the base and over the trussing system etc.
Insert the end in the carabine and tighten the fixation screw.
Secure chain
Mounting plate
Clamp
Eye bolt
5.5 Connection to the mains
Verify the power supply settings before applying power!
If you wish to change the power supply settings,see the chapter Appendix.
Connect the fixture to the mains with the enclosed power cable and plug.
The earth has to be connected!
The occupation of the connection-cables is as follows:
Cable (EU)
Brown
Light blue
Y ellow/Green
Cable (US)
Pin
Black
White
Green
Live
Neutral
Earth
5.6 DMX-512 connection/connection between fixtures
6
International
Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the
controller with the fixture or one fixture with another.
Occupation of the XLR-connection:
DMX-input
XLR mounting-plug:
DMX-OUTPUT
XLR mounting-socket:
1- Ground
2 - Signal (-)
3 - Signal (+)
1 1 - Ground
2 - Signal (-)
3 - Signal (+)
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a
120 resistor between Signal (-) and Signal (+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last fixture.
The transform of the controller line of 3 pins and 5 pins (plug and socket)
6. Control Board Operation
Function Table:
Mode
Condition
Function
Pan movement in positive or negative direction
YES--negative direction
Vertical movement in positive
or negative direction
YES--negative direction
Address code set
Reset
YES--reset
Rainbow color wheel change color linear
or stepping
YES--linear
Static color wheel change color linear
or stepping
YES--linear
Static gobo wheel change gobo linear
or stepping
YES--linear
DMX512 mode
Automatic
Working mode
Lamp on/off
7
Control board operation way:
LED
MODE
ENTER
UP
DOWN
1.Select working mode by pressing MODE.
2.Press ENTER to confirm the selection.
3.Press UP and DOWN to select working condition.
4.Press ENTER to confirm the selection.
7. DMX512 Channel Function
CHANNEL
FUNCTION
1
PAN
2
TILT
3
PAN movement fine adjust
4
TILT movement fine adjust
5
Scan speed adjust
6
Focus, from near to far
7
Rainbow color wheel
8
Static color wheel
9
Prism, prism auto-rotation
10
Static gobo wheel
11
Rotation gobo wheel
12
Gobo rotate
13
Iris, from big to small
14
Zoom
15
Beam out / strobe
16
Dimmer (Lamp on / off)
8
CHANNEL 1: PAN
Value
Effect
256
100
Clockwise 53 0
rotate
0
0.0
CHANNEL 2: TILT
9
Value
Effect
256
100
Anti-clockwise
280 rotate
0
0.0
CHANNEL 3: PAN movement fine adjust (16 BIT)
Value
Effect
256
100
Fine control of tilt
movement
0
0.0
0
CHANNEL 4: TILT movement fine adjust(16 BIT)
Value
10
Effect
256
100
0
0.0
Fine control of tilt
movement
CHANNEL 5: Scan speed adjust
Value
Slow
Effect
256
100
Slow
0
0.0
fast
Fast
CHANNEL 6: Focus
Value
Near
Far
11
Effect
256
100
close distance
0
0.0
far distance
CHANNEL 7: Rainbow color wheel
Value
Effect
200-255
79-100
Rainbow effect,
from slow to fast.
180-199
71-78
Dark orange
160-179
63-70
Firefly light
140-159
56-62
Pink
120-139
48-55
Blue
100-119
39-47
Orange
80-99
32-38
Green
60-79
24-31
Rose
40-59
16-23
Yellow
20-39
8-15
Red
0-19
0-7
White beam
CHANNEL 8: Static color wheel
Value
12
Effect
234-255
91-100
Increase color
temperature slip
(6000K)
208-233
81-90
Decrease color
temperature slip
(3200K)
182-207
71-80
Light blue
156-181
61-70
Sky blue
130-155
51-60
Light orange
104-129
41-50
Pale green
78-103
31-40
Light purple
52-77
21-30
Pale yellow
26-51
10-20
Light red
0-25
0-9
White beam
CHANNEL 9: Prism prism auto-rotation
Value
Effect
132-255
53-100
Three-facet prism
rotate from slow to
fast.
128-131
51-52
Stop
5-127
3-50
Three-facet prism
reverse rotate from
slow to fast.
0-4
0-2
Stop
200-255
79-100
Gobo flow effect,
from slow to fast.
180-199
71-78
Gobo 9
160-179
63-70
Gobo 8
140-159
56-62
Gobo 7
120-139
48-55
Gobo 6
100-119
40-47
Gobo 5
80-99
32-39
Gobo 4
60-79
24-31
Gobo 3
40-59
16-23
Gobo 2
20-39
8-15
Gobo 1
0-19
0-7
White beam
CHANNEL 10: Static gobo wheel
Value
13
Effect
CHANNEL 11: Rotating gobo wheel
Value
Effect
222-255
87-100
Glass gobo 6
185-221
73-86
Glass gobo 5
148-184
59-72
Glass gobo 4
111-147
44-58
Metal gobo 3
74-110
30-43
Metal gobo 2
37-73
15-29
Metal gobo 1
0-36
0-14
White beam
Value
Effect
159-255
62-100
Rotation gobo reverse
rotate from slow to fast
61-158
24-61
Rotation gobo rotate
from slow to fast
0-60
0-23
Gobo-indexing
CHANNEL 12:Rotation Gobo
14
CHANNEL 13: Iris
Small
Value
Effect
256
100
Minimum
0
0.0
Maximum
Big
CHANNEL 14: Zoom
Value
180-255
Zoom22
155-179
Zoom18
129-154
Zoom15
99-128
KEEP
66-98
Zoom22
33-65
Zoom18
0-32
15
Effect
100
0
Zoom15
CHANNEL 15:Beam out / strobe
Value
Effect
251-255
99-100
Beam out
20-250
8-98
strobe, from
slow to fast
0-19
0.0-7
Shutter
CHANNEL 16: Dimmer (Lamp on / off)
Value
16
Effect
70~255
27.5~100
Dimmer intensity
form 0% to 100%
60~69
23.5~27
Lamp off & reset
40~59
15.5~23
30~39
11.5~15
Lamp on & reset
0~29
0~11
Shutter
No function
8. Technical specifications
Voltage
AC210/230/240V ,50/60Hz
Fuse T10A @230V
AC100/110/120V ,50/60Hz
Fuse T15A @110V
Rated Power 850W
DMX512 Channel 16CHS
Color Temperature 7000K
Luminous
49000 LUX
Lamp: Philips MSR575/2 95V/575W GX 9,5
Optical System:
- High luminous-efficiency parabolic reflector
- Focus lens and multistep zoom lenses system
-Beam angles:15
18
22
- All lenses are anti-reflection coated
Rigging
-Stands directly on the floor
-Mounts horizontally or vertically with 2 clamps
-2 truss orientation
-Safety chain/cord attachment bolt
Temperatures
-Maximum ambient temperature ta: 40
-Maximum housing temperature tB (steady state): 80
Minimum distances
-Min.distance from flammable surfaces: 0.5m
-Min.distance to lighted object: 2.0m
Dimensions and weight
-Length of base (including handles): 379 mm
-Width of yoke: 428 mm
-Height (head horizontal): 476 mm
-Weight (net): 36.5 kg
17
9. Beampath
15
223
2400
99
1070
56 Foot-candles
600 LUX
5
1,3
10
2,63
15
3,95
20 Distance(m)
5,27 Diameter(m)
2
1
0
1
2
3
18
Beam opening(m)
3
radiation angle
773
8320
193
2080
86
930
48 Foot-candles
520 LUX
5
1,58
10
3,17
15
4,75
20 Distance(m)
6,34 Diameter(m)
2
1
0
1
2
3
22
4
radiation angle
583
6270
146
1570
65
700
36 Foot-candles
390 LUX
5
1,94
10
3,89
15
5,83
20 Distance(m)
7,78 Diameter(m)
3
Beam opening(m)
Beam opening(m)
3
radiation angle
892
9600
2
1
0
1
2
3
4
18
10. Maintenance and cleaning
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid
residues must not buildup on or within the fixture. Otherwise, the fixtures light-output will
be significantly reduced. Regular cleaning willnot only ensure the maximum light-output,
but will also allow the fixture to function reliably throughout its life.A soft lint-free cloth
moistened with any good glass cleaning fluid is recommended, under no circumstances
should alcohol or solvents be used!
DANGER :Disconnect from the mains before starting anymaintenance work
The front objective lens will require weekly cleaning as smoke-fluid tends to building up
residues, reducing thelight-output very quickly. The cooling-fans should be cleaned
monthly.
The gobos may be cleaned with a soft brush. The interior of the fixture should be cleaned at
least annually using a vacuum-cleaner or an air-jet.
The dichroic colour-filters, the gobo-wheel and the internal lenses should be cleaned
monthly.
To ensure a proper function of the gobo-wheel , we recommend lubrication in six month
intervals. The quantity of oil must not be excessive in order to avoid that oil runs out when
the gobo-wheel rotates.
There are no serviceable parts inside the device except for the lamp and the fuse.Please refer
to the instructions under "Fitting/Exchanging the lamp".Maintenance and service
operations are only to be carried out by authorized dealers.
Replacing the fuse
If the lamp burns out, the fine-wire fuse of the device might fuse, too. Only replace the fuse
by a fuse of same type and rating.Before replacing the fuse, unplug mains lead.
Procedure:
1) Unscrew the fuseholder on the rear panel of the base with a fitting screwdriver from the
housing (anti- clockwise).
2) Remove the old fuse from the fuseholder.
3) Install the new fuse in the fuseholder.
4) Replace the fuseholder in the housing and fix it.
19
11. Structure of the fixture
Light head fan
Lamp hodler
Front cover
Back panel
of lamp holder
Static gobo wheel
Lamp
Reflector
Top cover
Rotating gobo wheel
Color wheel B
Color wheel A
Tilt motor
Driver Board L
Belt
Driver Board R
Arm
Display Board
Transformer
Prtect board
Capacitance
Ballast
Seat cover
DMX512socket
Bottom Fan
Main PCB
Pan Motor
20
2
3
2
DMX
1
3
Rotation gobo
21
0V
12V
30V
U8
U1
U9
U2
zoom
Rotation gobo wheel
U1
DISPLAY BOARD
1
focus
U10
U3
2105L
Focus
U19
U11
U4
Zoom
U10
U12
U8
U11
U12
U5
Prism wheel
TILT 1
U9
U16
Prism rotation
main board
U18
TILT 2
U14
U17
U13
U15
PAN 2
U16
PAN 1
30V 12V 0V
DC12VFAN
stobe 1
DC12V FAN
11V
AC250V
30V
12V
0V
24V
AC230V
U8
U1
stobe 2
U9
U2
AC220V L
E
AC220V N
U10
U3
2105R board
Fixation gobo
Trigger
240V 220V
U11
U4
B
U12
U5
Color wheel B
MC4060
N
LP
U16
Color wheel A
60uF
12. Electrical diagram
13. Common faulty maintain
FAULTY
PHENOMENON
FAULTY PART
PART No.
Plug cable for pc
27-00-0010-04
Fuse
09-00-1002-01
Power switch
08-05-0400-03
Reach the lifespan or bed quality of bulb
Msd575/2 lamp
07-11-0017-00
Damaged trigger
B electronic trigger
11-10-0008-00
Damaged temperature switch
110 10A/250V
temperature switch
08-07-0020-00
Damaged ballast
575W ballast
06-03-Z020-00
FAULTY ANALYSIS
Power plug loose
Whole light cann't work
Damaged power switch
No light from bulb
Damaged fan on head of light
Complete light
can not reseat
Tilt can
not work
Focus can not work
Pan can
not work
Gobo can not
rotation
Prism wheel can
not rotation
92
25 12VDC
6-00-0008-02
80 80 25 12VDC fan
16-00-0008-04
Damaged display board
2105 display board
26-2A-YX2105DI-00
Whether the signal cable good or not
5 meters cable sets
27-04-0010-00
User manual
30-01-YX2105-00
Strap of focus break
270HTD/GT3M
weight 6m
18-06-0009-00
Damaged motor of focus
42BYGH004-02 motor
15-00-0073-01
Damaged motor of tilt
23HS0001-02 motor
15-00-0076-00
Strap of tilt break
420HTD/GT3M
weight 6mm
18-06-0009-02
Damaged motor of tilt
23HS0001-02motor
15-00-0076-00
Strap of pan break
552HTD/GT3M weight6mm
18-06-0009-03
Motor for rotation gobo wheel faulty
42BYGH026-1motor
15-00-0033-00
Motor of damp pole faulty
Damp pole
34-01-RD2105_03-00
Motor for rotation gobo faulty
16HY0002-16
15-00-0078-00
Rotation gobo wheel faulty
Rotation gobo wheel
34-01-RD2105_20-00
Rotation gobo wheel sensor faulty
YX2105 tilt sensor
26-2A-YX2105HRT-00
Motor for prism rotation faulty
16HY0002 motor
15-00-0007-00
Prism wheel faulty
Prism wheel
34-01-RD2105_56-00
Motor for Prism wheel faulty
42BYGH0026-2 motor
15-00-0079-00
Damp pole faulty
Damp pole
34-01-RD2105_03-00
Has not prism effect
Can not zoom
Motor for zoom faulty
42BYGH004-02 motor
15-00-0073-01
Fixed gobo wheel
can not change gobo
Motor for fixed gobo wheel faulty
42BYGH004-02 motor
15-00-0073-01
Can not strobe
/dimmer
Motor for strobe faulty
42BYGH004-02
15-00-0073-01
Motor for color wheel A
42BYGH026-2
15-00-0079-00
Motor of damp pole faulty
Damp pole
34-01-RD2105_03-00
Motor for color wheel B faulty
42BYGH004-06
15-00-0073-00
Fixed gobo wheel sensor faulty
Color wheel sensor
26-2A-YX2105HRCG-00
Display board
26-2A-2105DI-00
Display board CPU
00-89S8252-00
Color wheel A can
not change color
Color wheel B can
not change color
Color wheel/fixed gobo
wheel reseat faulty
Can not
automatism
R boa r d faulty
Bulb lighting,fans normal
Reset no succeed
L boa r d faulty
Rotation gobo
wheel cannot
change gobo
92
Damaged fan on bottom of light
Operate
MAIN BOARD CAN
NOT WORK
BULB AND FANS NORMAL
Bulb lighting ,whole
light normal but fans
can not work
Display board faulty
22
14.Component antitheses
Name
Motor(focus)
(main pcb)
Motor(aperture) (main pcb)
Motor(pan1/2) (main pcb)
Motor(tilt1/2)
(main pcb)
U11-12
(main pcb)
U8-9
(main pcb)
U15-18
(main pcb)
U13-14
(main pcb)
U19
(main pcb)
U10
(main pcb)
(main pcb)
Pan auto -reset sensor
Tilt auto -reset sensor
Pan sensor
Tilt sensor
Motor(gobo rotation)
Motor(gobo ) (2105l pcb)
Motor(zoom ) (2105l pcb)
Motor(prism wheel) (2105l pcb)
Motor(prism rotation) (2105l pcb)
U1-5 (2105l pcb)
U8-12 (2105l pcb)
U16
(2105l pcb)
Driver Board R/L
Rotation gobo wheel sensor
Motor(shutter)
(2105r pcb)
Motor(mix gobos) (2105r pcb)
Motor colour b) (2105r pcb)
Motor colour a) (2105r pcb)
Fixed gobo wheel sensor (2105r pcb)
U1-5 (2105r pcb)
U8-12 (2105r pcb)
U16
(2105r pcb)
Protect board
Fan on the head
DISPLAY PCB
fan on the bottom
transrormer
ballast
power supply filter
power swith
temperature switch
lamp
igniter
Back panel of lamp holder
Reflector
Color wheel A
Color wheel B
Front cover
Top cover
Belt
Arm
Seat cover
Static gobo wheel
DMX512 socket
PART NO.
15-00-0073-01
15-00-0073-01
15-00-0076-00
15-00-0076-00
00-6219-01
00-77E58-00
00-3772-00
00-39612-00
00-75176-00
00-77E58-00
26-2A-YX2105M-00
26-2A-YX2105GM-00
26-2A-YX2105GM-00
26-2A-YX2105HRP-00
26-2A-YX2105HRT-00
15-00-0078-00
15-00-0033-00
15-00-0073-01
15-00-0079-00
15-00-0007-00
00-6219-01
00-7528-01
00-89S52-00
26-2A-YX2105R-00
26-2A-YX2105HRT-00
15-00-0073-01
15-00-0073-01
15-00-0073-00
15-00-0079-00
26-2A-YX2105HRCG-00
00-6219-01
00-7528-01
00-89S52-00
26-3A-BHB-05
16-00-0008-02
26-2A-2105DI-00
16-00-0008-03
06-00-B074-00
06-03-Z020-00
05-6A-001-251
08-05-0400-03
08-07-0020-00
07-11-0017-00
11-10-0008-00
34-01-575TONG-47-AO
32-08-0016-00
34-01-2105_005-AO
34-01-2105_007-AO
34-06-2105_074-AO
34-06-575TONG-094-AO
18-06-0009-00
18-06-0009-01
18-06-0009-02
18-06-0009-03
34-06-575TONG-093-AO
34-05-575TONG-008-AO
34-01-2105_010-AO
10-02-0003-00
10-02-0004-00
23
REMARK
42BYGH004-02
42BYGH004-02
23HS0001-02
23HS0001-02
DRIVER CHIP
SOFTWARE CHIP
DRIVER CHIP
D/A CONVERSION CHIP
DMX CHIP
SOFTWARE CHIP
(MAIN PCB)
YX2105 tilt auto -reset sensor
YX2105 pan auto -reset sensor
Yx2105 pan sensor
Yx2105 tilt sensor
16HY0002-16
42BYGH026-1
42BYGH004-02
42BYGH026-2
16HY0002
DRIVER CHIP
D/A CONVERSION CHIP
SOFTWARE CHIP
2105R PCB
Yx2105 tilt sensor
42BYGH004-02
42BYGH004-02
42BYGH004-06
42BYGH026-2
YX2105sensor
DRIVER CHIP
D/A CONVERSION CHIP
SOFTWARE CHIP
time-lapse protect board
92 92 25 12VDC
2105DI.PCB
80 80 25 12VDC
11V/24V/230V/250V/220W
575W ballast
250V 16A
250V 15A
110 250V 10A
MSR575/2
220/240V 50/60Hz
RD-575TONG-047-A
133
RD-2105-005-A
RD-2105-007-A
RD-2105-074-A
RD-575TONG-094-A
270HTD/GT 3M/RPP3 Weight 6mm
447HTD/GT 3M/RPP3 Weight 6mm
420HTD/GT 3M/RPP3 Weight 6mm
522HTD/GT 3M/RPP3 Weight 7mm
RD-575TONG-093-A
RD-575TONG-008-A
RD-2105-010-A
3-2905 32 26 25
3-2906 32 26 25.5
R61B
4K7
R55
330
VCC
1
2
3
4
C13
104
GND
GND
VCC
VCC
C37
OTILT
1
2
3
4
J11
R60
1
X2
Y1
24MHZ
X1
R13
10K
RST
4
3
2
1
C36
J1
C1
104
E7
10U
VCC
+30
1
2
3
4
5
6
7
8
15
14
17
16
RD
102
C48
R14
10K
75176
R
RE
DE
D
U12
IDC10
102
C29
1R8
102
C49
P21
P20
8
7
6
5
RD
WR
RXD
OPAN
1
2
3
4
J12
+5
RESET
X1
X2
EA/VP
9V
9V
R56
330
D19
1
2
3
J6
102
C50
R16
10K
R53 100
R51 100
D18
D20
TVS
R47
4K7
RXD
TXD
ALE/P
PSEN
P20
P21
P22
P23
P24
P25
P26
P27
INT1
INT0
T1
T0
P00
P01
P02
P03
P04
P05
P06
P07
20K
102
R10
C33
U1 102
L6219
20K
C32
R9
P10/T
P11/T
P12
P13
P14
P15
P16
P17
+5
77E58
R3 102
1K
R7
U5
R15
10K
VCC
BA+
GND
104
C14
9
19
18
RST
X1
X2
VCC 31
T1
T0
VCC
INT1 13
INT0 12
P10
P11
P12
P13
P14
P15
10
9
8
7
6
5
4
3
2
1
J5
E1
470U/50V
24
23
22
21
20
19
18
17
16 T1
15
14
13
OUT1A
VS
OUT2A SENSE1
SENSE2 COMP1
COMP2 OUT1B
I01
OUT 2B
GND
GND
GND
GND
I02
I11
I12
PHASE1
PHASE2 VREF1
VREF2
RC1
RC2
VSS
1
2
3
4
5
6
7
8
9
10
11
12
T0
102
C51
P27
P26
R17
10K
10
11
30
29
21
22
23
24
25
26
27
28
39
38
37
36
35
34
33
32
4
18
1
19
MTILT
1
2
3
J13
100
R54
DMX IN
R52
100
GND
3
2
1
J8
P20
P21
P22
P23
P24
P25
P26
P27
D0
D1
D2
D3
D4
D5
D6
D7
3
2
VCC 20
VCC
104
104
C20
P22
R48
4K7
D7
D6
D5
D4
D3
D2
D1
D0
P12
P11
D7
D6
D5
D4
D3
D2
D1
D0
P12
P10
AD7528
VrefA
VrefB
6
7
8
9
10
11
12
13
14
5
16
6
7
8
9
10
11
12
13
14
5
16
39612
MPAN
1
2
3
4
J14
104
C15
+5
D1
D0
D1
D2
D3
D4
D5
D6
D7
104
C21
+5
D23
TVS
P25
104
C22
P25
P24
R50
4K7
15
20
1
17
3
2
18
19
4
1K
R26
GRE
15
20
1
17
3
2
18
19
4
+5
15 GND
16 P13
6 P15
14
13
12
11
10
9
8
7
R49
4K7
D22
TVS
P24
VDD
D7
D6
D5 SIGN1
D4
DA1
D3 SIGN2
D2
DA2
D1
D0
NC
A0
RST
WR
Vref
CS
VSS
U7
39612
VDD
D7
D6
D5 SIGN1
D4
DA1
D3 SIGN2
D2
DA2
D1
D0
NC
A0
RST
Vref
WR
CS
VSS
104
C7
CS
WR
DACA/B
lsbDB0
DB1
DB2
DB3
DB4
DB5
DB6
msbDB7
U6
VCC
D21
TVS
P22
AN-GND
RfbB
OUT-B
RfbA
OUT-A
U3
C3
17
Vdd
104
19
20
4
3
AC10V8
2
1
J16
AC24V
1
2
J15
15K
VCC
R20
19
20
4
3
C4
104
+5
3772
1K
R22
C38 C42
222 102
Phase1
VR1
Phase2
VR2
U10
C16
104
15K
Phase1
VR1
Phase2
VR2
U8
C8
104
RP1
4K7
1
2
3
4
5
6
7
8
9
VCC
R18
D0
D1
D2
D3
D4
D5
D6
D7
VCC
RC
1
RC
+5
F2
F1
3772
1K
R27
5A
10A
C41 C52
222 102
1
1R8
R1
1K C28
C1
21
C1
21
+30
+30
1K
1K
R28
R57 C23
104
R58 C24
104
0.5 C53
102
R39
9
R23
0.5 C43
102
R31
Vbb1
Mb2
Ma2
Ma1
Mb1
0.5
R33
Mb2
Ma2
Ma1
Mb1
0.5
R41
D27
KBU808
R42
0.5
11
8
15
12
D26
KBU808
R40 0.5
R34
0.5
11
8
15
12
7
8
9
10
11
12
13
14
R32 0.5
D7
D6
D5
D4
D3
D2
D1
D0
6
P15
P14 16
GND 15
1
2
3
4
J3
VCC
OUT-A
1
2
3
4
J9
E3
470U/50V
C26
104
E8
C25
2200U/25V 104
+12
E9
2200U/50V
+30
GND
C17
104
+30
C9
104
2
3
D25
KBU808
+30
+5
3772
1K
R24
C39 C44
222 102
Phase1
VR1
Phase2
VR2
R62 R59
2/6W
10K
+12
15K
VCC
R21
19
20
4
3
U11
C18
104
15K
C11
104
20K
102
R12
C35
102
20K
C34
R11
Phase1
VR1
Phase2
VR2
U9
C10
104
VCC
R19
19
20
4
3
VCC
20 VCC
19
1
18
4
+30
E6
470U/50V
D11
D13
TILT1
FR104 FR104
D10
D12
FR104 FR104
+30
RfbA
OUT-B
RfbB
AN-GND
VrefB
VrefA
D3
D5
PAN1
FR104 FR104
D2
D4
FR104 FR104
+30
104
C5
msbDB7
DB6
DB5
DB4
DB3
DB2
DB1
lsbDB0
DACA/B
WR
CS
U4
AD7528
Vdd
17
C2
5
6
17
18
22
16
7
GND
GND
GND
GND
VCC
VMM1
VMM2
E1
13
5
6
17
18
22
16
7
GND
GND
GND
GND
VCC
VMM1
VMM2
E1
13
E2
10
14
C2
2
C2
2
Vbb2
9
Vbb2
RC
1
RC
14
Vbb1
C1
21
C1
+5
1
3772
E10
100U/25V
Vin
1K
R29
C40 C46
222 102
21
102
C30
1R8
R6
+30
VCC
1K
R25
+30
0.5 C45
102
R35
1K
R30
U13
7805
Vout
0.5 C47
102
R43
R36
9
VCC
GND
2
E2
10
5
6
17
18
22
16
7
GND
GND
GND
GND
VCC
VMM1
VMM2
E1
13
5
6
17
18
22
16
7
GND
GND
GND
GND
VCC
VMM1
VMM2
E1
13
C2
2
C2
2
Mb2
Ma2
Ma1
Mb1
R37 0.5
0.5
1R8
R8
102
C31
Mb2
Ma2
Ma1
Mb1
0.5
R45
R44 0.5
R38
0.5
E2
14
Vbb1
14
Vbb1
Vbb2
9
Vbb2
10
R2
1K
11
8
15
12
11
8
15
12
+5
+30
C6
104
1
2
3
4
J10
VCC
D24
TVS
+12
+30
+30
C19
104
+30
C12
104
1
2
3
J7
E5
470U/50V
D15
D17
TILT2
FR104 FR104
D14
D16
FR104 FR104
+30
E4
470U/50V
D7
D9
PAN2
FR104 FR104
1
2
3
4
J4
E2
470U/50V
J2
1
2
3
4
U2
L6219
D6
D8
FR104 FR104
+30
R4
1K
E11
C27
100U/25V 104
3
R46
0.5
E2
10
24
1
12
11
10 INT0
9
8
7
6
5
4
3
2
1
VSS
RC2
RC1
VREF2
VREF1 PHASE2
PHASE1
I12
I11
I02
GND
GND
GND
GND
I01
OUT 2B
OUT1B COMP2
COMP1 SENSE2
SENSE1 OUT2A
VS
OUT1A
13
14
15
INT1 16
17
18
19
20
21
22
23
24
R5
15.MAIN PCB
25
15P
C1
15P
C2
X1
T1
24MHZ
X2
ENTER
UP
K4
DOWN
K3
FUNC
K2
K1
VCC
P10
P11
P12
E2
X1
10u/50V X2
R9
10K
VCC
P26
P25
P24
P27
R10
4K7
17
16
9
19
18
31
15
14
13
12
1
2
3
4
5
6
7
8
89S8252
RD
WR
RESET
X1
X2
EA/VP
T1
T0
INT1
INT0
P10
P11
P12
P13
P14
P15
P16
P17
U1
1
2
3
RXD
TXD
ALE/P
PSEN
P20
P21
P22
P23
P24
P25
P26
P27
P00
P01
P02
P03
P04
P05
P06
P07
10
11
30
29
21
22
23
24
25
26
27
28
39
38
37
36
35
34
33
32
P22
P23
P24
P25
P26
P27
P00
P01
P02
P03
P04
P05
P06
P07
4K7
GND
GND
VCC
VCC
P10
P00
P01
P02
P03
P04
P05
P06
P07
IDC10
10
9
8
7
6
5
4
3
2
1
J1
16
15
3
2
1
18
17
4
P23
4K7
R3
R4
4K7
U2
DR56
1a DPY
2a
1b
2b
a
a
1c
2c
1d f g b f g b 2d
1e
2e
c e
c 2f
1f e
d
d
1g
2g
dp
dp
1dp
2dp
Q1
9012
13
V+
J2
P22
R2
4K7
14
V+
R1
11
10
8
6
5
12
7
9
P00
P01
P02
P03
P04
P05
P06
P07
Q2
9012
16
15
3
2
1
18
17
4
R6
4K7
P00
P01
P02
P03
P04
P05
P06
P07
E1
10u/50V
4K7
VCC
P12
R5
U3
DR56
C3
104
P11
4K7
R7
R8
4K7
1a DPY
2a
1b
2b
a
a
1c
2c
1d f g b f g b 2d
1e
2e
c e
c 2f
1f e
d
d
1g
2g
dp
dp
1dp
2dp
Q3
9012
13
V+
VCC
14
V+
VCC
11
10
8
6
5
12
7
9
P00
P01
P02
P03
P04
P05
P06
P07
Q4
9012
16.DISPLAY PCB
1K
1R8
R9
1K
R25
1R8
R1
P20
C1
102
R33
20K
R41
20K
1
2
3
4
5
6
C9
7
102
8
9
INT0 10
11
12
C17
102
L6219
J5
C25
102
L6219
C26
102
OUT1A
VS
OUT2A SENSE1
SENSE2 COMP1
COMP2 OUT1B
OUT 2B
I01
GND
GND
GND
GND
I02
I11
I12
PHASE1
PHASE2 VREF1
VREF2
RC1
RC2
VSS
U5
C18
102
OUT1A
VS
OUT2A SENSE1
SENSE2 COMP1
COMP2 OUT1B
OUT 2B
I01
GND
GND
GND
GND
I02
I11
I12
PHASE1
PHASE2 VREF1
VREF2
RC1
RC2
VSS
19
1
2
3
4
5
6
7
8
9
10
11
12
U1
GND
6
P10
P15 16
GND 15
18
4
VrefB
VrefA
GND
R17
18
4
VrefB
VrefA
1
AN-GND
DACA/B
WR
CS
RfbB
4
3
2
1
19
RfbB
20 VCC
OUT-B
1
AN-GND
DACA/B
WR
CS
6
P10
P11 16
GND 15
+30
Vdd
R10
1R8
C37
104
C30
104
17 VCC
U12
AD7528
R42
20K
VCC
C10
102
1K
R26
C16
104
17 VCC
24
23
22
21
20
19
18
17
16 INT1
15
14
13
+30
Vdd
U8
AD7528
VCC
C2
102
1K
R2
1R8
E2
470U/50V
R18
R34
20K
24
23
22
21
20
19
18
17
16 P21
15
14
13
VCC
2
C15
104
1R8
R3
1K
R19
C11
104
C43
104
P22
C3
102
R35
20K
1
2
3
4
5
6
7
8
9
10
11
12
J2
C19
102
L6219
C20
102
OUT1A
VS
OUT2A SENSE1
SENSE2 COMP1
COMP2 OUT1B
OUT 2B
I01
GND
GND
GND
GND
I02
I11
I12
PHASE1
PHASE2 VREF1
VREF2
RC1
RC2
VSS
U2
GND
4
3
2
1
20 VCC
OUT-B
3
RfbA
msbDB7
DB6
DB5
DB4
DB3
DB2
DB1
lsbDB0
7
8
9
10
11
12
13
14
P07
P06
P05
P04
P03
P02
P01
P00
18
4
VrefB
VrefA
18P
C32
T1
24MHZ
C31
18P
6
P10
P14 16
GND 15
19
RfbB
1
AN-GND
DACA/B
WR
CS
Vdd
1
2
3
4
5
6
7
8
15
14
WR
RST
17
16
9
19
18
VCC 31
T1
INT1 13
INT0 12
P10
P11
P12
P13
P14
P15
89S52
RD
WR
RESET
X1
X2
EA/VP
T1
T0
INT1
INT0
P10/T
P11/T
P12
P13
P14
P15
P16
P17
U16
C27
104
17 VCC
U9
AD7528
VCC
C4
102
1K
C38
104
R4
1R8
E3
470U/50V
R20
R36
20K
24
23
22
21
20
19
18
17
16 P23
15
14
13
+30
RXD
TXD
ALE/P
PSEN
P20
P21
P22
P23
P24
P25
P26
P27
P00
P01
P02
P03
P04
P05
P06
P07
1R8
R5
1K
R21
C12
104
P20
P21
P22
P23
P24
P25
P26
P27
P00
P01
P02
P03
P04
P05
P06
P07
10 RXD
11
30
29
21
22
23
24
25
26
27
28
39
38
37
36
35
34
33
32
P24
C5
102
R37
C21
20K
1
2
3
4
5
6
7
8
9
10
11
12
J3
VCC
102
L6219
C22
102
OUT1A
VS
OUT2A SENSE1
SENSE2 COMP1
COMP2 OUT1B
OUT 2B
I01
GND
GND
GND
GND
I02
I11
I12
PHASE1
PHASE2 VREF1
VREF2
RC1
RC2
VSS
U3
GND
4
3
2
1
20 VCC
OUT-B
VCC
2
OUT-A
3
RfbA
msbDB7
DB6
DB5
DB4
DB3
DB2
DB1
lsbDB0
7
8
9
10
11
12
13
14
P07
P06
P05
P04
P03
P02
P01
P00
18
4
VrefB
VrefA
6
P10
P13 16
GND 15
19
RfbB
1
AN-GND
DACA/B
WR
CS
4
3
2
1
20 VCC
OUT-B
Vdd
R47
10K
RST
E1
10U
VCC
4K7
1
2
3
4
5
6
7
8
9
RP1
C34
104
C36
104
T1
WR
104
C35
R12
4K7
R11
100
VCC
+12
C28
104
17 VCC
U10
AD7528
VCC
C6
102
1K
104
C42
R48
4K7
E5
100U
1
1R8
R7
1K
R23
C13
104
4
3
2
1
J6
Vi n
P26
C7
102
U21
7805
To Hall board
R6
1R8
E4
470U/50V
R22
R38
20K
24
23
22
21
20
19
18
17
16 P25
15
14
13
+30
R39
20K
1
2
3
4
5
6
7
8
9
10
11
12
J4
Vout
C23
102
L6219
C24
102
OUT1A
VS
OUT2A SENSE1
SENSE2 COMP1
COMP2 OUT1B
OUT 2B
I01
GND
GND
GND
GND
I02
I11
I12
PHASE1
PHASE2 VREF1
VREF2
RC1
RC2
VSS
U4
GND
1
VCC
2
OUT-A
3
RfbA
msbDB7
DB6
DB5
DB4
DB3
DB2
DB1
lsbDB0
7
8
9
10
11
12
13
14
P07
P06
P05
P04
P03
P02
P01
P00
19
RfbB
18
4
VrefB
VrefA
6
P10
P12 16
GND 15
GND
OUT-A
VCC
2
OUT-A
3
RfbA
msbDB7
DB6
DB5
DB4
DB3
DB2
DB1
lsbDB0
7
8
9
10
11
12
13
14
P07
P06
P05
P04
P03
P02
P01
P00
26
2
AN-GND
DACA/B
WR
CS
4
3
2
1
20 VCC
OUT-B
Vdd
VCC
E7
100U
D2
TVS
100
R13
R14
4K7
VCC
RXD
3
+30
3
2
1
J7A
D1
TVS
2
1
J7B
To Main Board
C33
104
C29
104
17 VCC
U11
AD7528
R8
1R8
E6
470U/50V
VCC
C8
102
1K
R24
R40
20K
24
23
22
21
20
19
18
17
16 P27
15
14
13
VCC
2
OUT-A
3
RfbA
msbDB7
DB6
DB5
DB4
DB3
DB2
DB1
lsbDB0
7
8
9
10
11
12
13
14
P07
P06
P05
P04
P03
P02
P01
P00
J1
C14
104
+30
+12
+12
FAN
1
2
J9
To Main Board
1
2
3
J8
17.DRIVER PCB