Download twelve channel power dmx switch pack user`s manual introduction

TWELVE CHANNEL POWER DMX SWITCH PACK
USER'S MANUAL
INTRODUCTION:
The unit is a 12 channel power DMX switch pack. It is controlled by itself or DMX-512. There
are eight chase program inside and the speed of these chase program can be selected. Led displays
DMX address and program number and chase speed. These data can be memoried. We recommend
that you take time to read this manual fully before you attempt to use the unit.
SPECIFICATION:
Power input ................................................................. Ac 230v~50Hz,16A
Power output ....................................................... Per channel 5A, total 16A
DMX input .............................................................. 3pin XLR male socket
DMX output ......................................................... 3pin XLR female socket
Fuse ............................................................. F 6.3A 250V,5X20MM,12 pcs
Dimension ........................................................................ 480X146X76mm
Weight ............................................................................................ 4.0kg
OPERATION:
1. Front panel
DMX SIGNAL
7
-1306
DISPLAY
FUNCTION
DMX
: 001-512 DMX START ADDRESS
AUTO
: SPEED 1-9 1: SLOW ; 9: FAST
12
BUILT - IN PROGRAM
FUSE1 FUSE2 FUSE3 FUSE4 FUSE5 FUSE6 FUSE7 FUSE8 FUSE9 FUSE10 FUSE11 FUSE12
: PROGRAM 1 - 8
6.3A/250V 5X20mm X 12
CHANNEL
POWER
1
UP
DOWN
MODE
4
5
6
DMX
SWITCH PACK
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12
2
3
1 .....................................................................................................power indicator
2 ............................................................................................................output fuse
3 .....................................................................................................output indicator
4 ...........................................................................................................up button
5 ........................................................................................................down button
6 ........................................................................................................mode button
7 .......................................................................................................LED display
2.Real panel
5 A PER CHANNEL ; TOTAL 16 A
CAUTION
POWER INOUT
110V
230V
1
WARNING: THIS APPARATUS MUST BE EARTHED
COM
CH12 CH11 CH10 CH9 CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
2
3
4
1 .....................................................................................................power input
2 .....................................................................................................load output
3 ................................................................................................... . dmx output
4 .....................................................................................................dmx input
3. Operate
a.Check out load output then put the power input on.
b.Push the MODE button.you can select automation mode, one program mode and DMX
mode,corresponding LED DISPLAY show you A--,P--,D--.
c.In automation mode, push UP or DOWN button, corresponding LED DISPLAY show you
S-X. Push UP or DOWN button,you can select X from 1 to 9. It means the speed of
automation can be selected. 9 is the fastest and 1 is the slowest.NO button push
down after two second, LED DISPLAY will go back to A--. In this mode, all program
will run eight times.
d.In one program mode, push UP button,you can select the run speed,push DOWN button,
you can select one program from 1 to 8.In this mode,only the one program run.No
button push down after two second, LED DISPlAY will go back to P--.
E.In DMX mode,push UP or DOWN button,you can select DMX start address from 1 to 512.
If the unit receive DMX single,the indicator of DMX single will blink.
Caution:
1.to prevent fire or shock hazard, do not expose this apparatus to rain or moisture.
2.this apparatus must be earthed.
3.do not try to repair it when the circuit is out of order,send back to you supplier
for repairing.
4.we suggest that you should use a circuit breaker(16A)