Download Manual - VibrAlign

B E LT H O G T O O L I N S T R U C T I O N S
BLETL T
HG
OG
OLO ILN ISNTSRTURCUTC
T INOSN S
BE
HO
T OTO
IO
B E LT H O
G TOOL INSTRUCTIONS
Preliminary
Steps
Pre-alignment:
Preliminary
Steps
Preliminary
Steps
1. Preliminary
Lock-out/ tag-outSteps
equipment as per the Safety
Pre-alignment:
Pre-alignment:
Department regulations at your facility.
Pre-alignment:
1.
equipment
as
per
Safety
2.Lock-out/
Checktag-out
thetag-out
condition
of the
grooves
1. Lock-out/
equipment
asVper
the the
Safety
1. Lock-out/
tag-out at
equipment
as per the Safety
Department
regulations
your
facility.
Department
regulations
at
your
facility.
to ensure that they are not worn.
Department regulations at your facility.
of the
V assure
groovesthat
2. C2.
heck
the the
condition
the
V grooves
3.Check
Check
runcondition
out onofpulleys
to
2.
Check
the
condition
of
the V grooves
to ensure
that
they
are
not
worn.
to
ensure
that they
worn.
they
are square
to are
the not
shafts.
to ensure that they are not worn.
Check
on pulleys
to assure
3. C3.
heck
run run
out out
on pulleys
to assure
thatthat
they are square to the shafts.
3. Check
run out on pulleys to assure that
Tool
Set
they
areup:
square to the shafts.
Tool Set they
up: are square to the shafts.
1. Select the
proper tip size for the pulleys.
1. M
Tool
ounting
guides”)
come in 4units.
sizes.
Settips
up:(“V-belt
2. Designate
movable
and stationary
Tool
Set
up: tip size for the pulleys.
Select
the
proper
1. Select
the proper
tip size
for the pulleys.
The driver
is usually
the movable
unit.
1.2Select
theeach
proper
sizeunit.
for The
the pulleys.
Insert
tips into
BelttipHog
tips
2.
stationary
units.
3.Designate
Mount themovable
units on and
the pulleys
are used
to centermovable
the Beltand
Hog;stationary
the tips units.
2. Designate
The
is usually
the movable unit.
withdriver
the “On/Off”
buttons
must contact
bothiswalls
of the
The driver
usually
the sheaves,
movable but
unit.
3. Mount
the
units
on
the pulleys
facing
the
same
direction.
will not
“fill
the
groove”.
3. Mount the units on the pulleys
with the “On/Off” buttons
2. Designate
andbuttons
stationary units.
withmovable
the “On/Off”
facing the same direction.
The driver
is usually
the
movable unit.
facing
the same
direction.
1
2
1
2
3
4
TOO
SMALL
3
4
TOO
SMALL
TOO
SMALL
TOO
BIG
GOOD
TOO
BIGTOO
BIG
GOOD
GOOD
Note:the
The
laser
projected
3. M
ount
units
on line
the pulleys
withfrom
the the stationary unit
the movable
unitsame
is the
reference line.
“On/Off” to
buttons
facing the
direction.
Note: The laser line projected from the stationary unit
Note:1The laser line projected from the stationary unit
theline
movable
unit from
is thethe
reference
line.unit
Note:Step
T
he to
laser
projected
stationary
to the movable
unitreference
is the reference
line.
to
the
movable
unit
is
the
line.
Vertical Alignment (twist):
Misaligned
Misaligned
Laser radiation is emitted
from this apperture
Laser radiation is emitted
from this apperture
Misaligned
M
M
Aligned
Laser radiation is emitted
from this apperture
Laser radiation is emitted
from this apperture
M
Laser radiation is emitted
from this apperture
Laser radiation is emitted
from this apperture
M
M
Laser radiation is emitted
from this apperture
Laser radiation is emitted
from this apperture
Laser radiation is emitted
from this apperture
M
Laser radiation is emitted
from this apperture
Laser radiation is emitted
from this apperture
Vertical
(twist):
motorAlignment
(or movable
pulley), determine the
Vertical
Alignment
(twist):
Vertical
Alignment
(twist):
1. Looking
atmisalignment.
the movable
unit mounted on the
angular
1. Looking at the movable unit mounted on the
determine
theadding
2. motor
Move
the
motor
(orpulley),
movable
pulley)
1. Looking
at (or
themovable
movable
unit
mounted
on by
the
motor or
motor (or movable pulley), determine the
angular
misalignment.
(or movable
pulley),
thefront
angular
removing
shimsdetermine
under both
feet misalignment.
or both back
angular misalignment.
Move
the motor
(or line
movable
pulley)
by
feet until
the laser
projected
onadding
theadding
movable
2. M2.
ove
motor
movable
pulley)
by
or or or
2.the
Move
the (or
motor
(or movable
pulley)
by adding
removing
shims
under
both
front
feet
or
both
back
unit
is
parallel
to
the
center
line
of
the
target
label.
removing shims under both front feet or both back
removing shims under both front feet or both back
feet
until
the
laser
line
projected
on
the
movable
feet until the laser line projected on the movable
feet untiltothe
laser lineline
projected
on thelabel.
movable
unit unit
is parallel
of the
target
is parallelthe
to center
the center line
of the
target label.
unit is parallel to the center line of the target label.
Laser radiation is emitted
from this apperture
Step 1
1. Step
Looking1at the movable unit mounted on the
Step
1
Aligned
Aligned