Download Atomos Ninja. User Manual

Atomos Ninja
User Manual
Version 1.0 – March 2011
Have you registered your Ninja yet? Upgrade to 3 year warranty* now.
Website: www.atomos.com | Sales: [email protected] | Support: [email protected]
Contents
Safety Instructions
Warranty & Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1. What’s included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. What you also need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
What drives should you use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Solid Sate Drives (SSDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Mechanical Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Backing up and archiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
HDMI Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Mounting disks in the Master Caddy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Connecting and powering up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AC Power Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Power ON / Power OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5. Ninja connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6. Other physical features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Master Caddy – Insert/Eject . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Screw mounts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Using the Ninja. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
The User Interface in detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ninja’s Touchscreen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
The Home Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Batteries Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Auto Switching/Manual Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Monitoring and Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connect to Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Before recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Anti-shock technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9. Connecting and Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connect to Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Importing Ninja Footage into Final Cut Pro . . . . . . . . . . . . . . . . . . . . . . . . . 14
Anti-Shock Technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
10. Software Upgrades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Updating ATOM-OS (Firmware) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Problems when installing Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
The Ninja is designed to a high standard but there are some things
you should be aware of to prolong the life of the unit and for your
own safety.
11. Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Conventions
To keep things simple but clear, we’ve only adopted two
conventions in this manual:
Batteries and power supplies
The batteries supplied with the Ninja are powerful, professional devices,
designed to retain enough energy to supply the Ninja for hours. You
should avoid short-circuiting the battery connections because this can
cause a high current to flow which can damage the cells and even pose
a fire hazard. For example, you should not carry batteries in a bag or
pocket where they may contact other metal objects such as coins.
The power supply and battery charger included are intended for use with
the Ninja and nothing else. Keep the power supply, plug and cable away
from water and unplug from the mains electricity socket when not in use.
Disconnect power supplies before cleaning the Ninja or its components.
Using the Ninja safely
Although the Ninja is very lightweight compared to all the devices it
replaces, it is still a solid object that could cause injury if misused.
• Always make sure that the Ninja is mounted securely and is unable to
fall onto anyone nearby. This is especially important when there are
children present who might be tempted to pull on cables.
• Always ensure that cable runs to the Ninja are clearly visible and do
not present a trip hazard.
• Do not place on uneven or unstable surfaces.
• Do not insert anything but Ninja Master Disk caddies in the Master
Disk slot on the side of the Ninja.
• Do not touch the Ninja’s screen with sharp, metallic or abrasive objects.
• The Ninja can become warm or hot with prolonged use. Do not place it
in contact with your lap or any part of your body where such warming
could cause discomfort or injury.
• Do not expose to strong electrical or magnetic fields.
• Do not expose to or use near liquids, rain or moisture.
• Do not dispose of the Ninja or its batteries in municipal waste and do not
incinerate it or its batteries, but follow local regulations for safe disposal
Care of disk drives
Spinning disks and SSDs are very sensitive to damage from static
electricity. Please observe all the usual precautions when handling them.
Please see the section Mechanical shock and vibration later in this
manual for information about how to handle and care for your disk drives.
Small parts
The Ninja carry-case contains small parts that could be a choking hazard
for small children.
A helpful tip, suggestion or something to note because
it’s not obvious at first
Menu
Monospaced text indicates a menu or touch action
Important note about disk types:
HDD/SSD/Disk Drives etc
To avoid any confusion, when we’re talking about “traditional” spinning
disk drives, we’ll refer to them as “spinning disks”. Solid-state drives
we’ll refer to as “SSDs” (Solid State Drives).When we want to refer to
both types of drive, we just call them “disks”.
Atomos Ninja. User Manual V1.01
2
Warranty & Conditions
Notice
Software License Agreement
Copyright © 2011 ATOMOS Global Pty Ltd (‘referred to as ATOMOS’).
All rights reserved. All information in this document is subject to
change without notice. No part of the document may be reproduced
or transmitted in any form, or by any means, electronic or mechanical,
including photocopying or recording, without the express written
permission of ATOMOS. A reference to ATOMOS includes its related
entities, subsidiaries and parent company.
IMPORTANT, PLEASE READ CAREFULLY. THIS IS A LICENSE
AGREEMENT.
This ATOMOS software, related documentation, any included sample
images and other files (the “Software”), is protected by copyright laws
and international copyright treaties, as well as other intellectual property
laws and treaties. The Software is licensed, not sold.
Trademarks
NINJA, ATOMOS are registered trademarks of ATOMOS, Apple,
the Apple logo, AppleShare, AppleTalk, FireWire, iPod, iPod Touch, Mac,
and Macintosh are registered trademarks of Apple Inc. Final Cut Pro,
QuickTime and the QuickTime Logo are trademarks of Apple Inc. All other
trademarks are the property of their respective holders.
International Hardware Limited Warranty
ATOMOS warrants that:
• the main product, not including TFT/LCD, or any external accessories,
will be free from defects in materials and workmanship for a period of
1 years from the date of purchase, the user may upgrade to a 3 year
warranty upon registering their product at www.atomos.com
• the TFT/LCD, batteries, battery charger and HDD/SSD docking station
will be free from defects in materials and workmanship for a period of 1
year from the date of purchase.
This warranty is exclusively for the benefit of the original purchaser and is
not assignable or transferable.
If during the warranty period the product is shown to be defective
ATOMOS may at its option:
a) replace the goods or supply equivalent ones, b) repair the goods, c)
pay the cost of replacing the goods or of acquiring equivalent ones and d)
paying the cost of having the goods repaired;
The customer must notify ATOMOS of any defect in the goods in
writing prior to the expiry of the warranty periods set out above. The
customer will be solely responsible for returning the goods to ATOMOS
or its authorized distributor. Upon acceptance of a warranty claim by
ATOMOS, where ATOMOS repairs or replaces the goods, it will be
responsible for reasonable shipping costs incurred in sending the goods
to the Customer, provided that customer is located in a country in which
ATOMOS has an authorized distributor or repair centre or agent.
Warranty Exclusions
This warranty applies only to defects in workmanship and does not cover
defects caused by:
• A failure to comply with the then current operating instructions issued
by ATOMOS;
• Neglect;
• Improper or negligent acts or omissions;
• Unauthorised repairs or attempted repairs;
• Tampering with or modification of the goods;
• Connection to incompatible equipment or power sources;
• Exposure to water or weather;
• Exposure to magnetic fields or corrosive liquids or substances;
This End User License Agreement (“EULA”) is a legal agreement between
you (either an individual or a single entity) and ATOMOS with regard to
the copyrighted Software provided with this EULA. Use of the Software
provided to you by ATOMOS in whatever form or media, will constitute
your acceptance of these terms, unless separate terms are provided
by the software supplier, in which case certain additional or different
terms may apply. If you do not agree with the terms of this EULA, do
not download, install copy or use the Software. By installing, copying or
otherwise using the Software, you agree to be bound to the terms of this
EULA. If you do not agree to the terms of this EULA, ATOMOS is unwilling
to license the Software to you.
1.Eligible licensees. This Software is available for license solely to
purchasers of the ATOMOS Ninja, who have purchased a unit
manufactured by ATOMOS Ninja and purchased through an ATOMOS
authorized reseller, with no right of duplication or further distribution,
licensing or sub-licensing.
2.License Grant. ATOMOS grants you a personal, non-transferable and
non-exclusive right to use the copy of the Software provided with this
EULA. You agree you will not copy the Software except as necessary
to use it with the ATOMOS Ninja. You agree that you may not copy
the written materials accompanying the Software. Modifying, reverse
engineering, translating, renting, copying, transferring or assigning
all or part of the Software or any rights granted hereunder, to any
other persons or reverse engineering the hardware on which the
Software runs, is strictly prohibited. The software is license, not sold.
You acknowledge that no title to intellectual property in the Software
is transferable to you. You further acknowledge that title and full
ownership rights to the Software will remain the exclusive property
of ATOMOS and/or its suppliers, and you will not acquire any rights
to the Software, except as expressly set forth above. All copies of
the software will contain the same proprietary notices as contained
in or on the Software. All title and copyrights in and to the Software
(including but not limited to any images, animations, video, audio, text
incorporated), the accompanying printed materials, and any copies of the
Software are owned by ATOMOS or its suppliers.
3.Reverse engineering. You agree that you will not attempt, and if you are
a corporation, you will use your best efforts to prevent your employees
and contractors from attempting to reverse compile, derive circuits,
modify, translate or disassemble the Software and/or the Atomos Ninja
in whole or in part. Any failure to comply with the above or any other
terms and conditions contained herein will result in the automatic
termination of this license and the reversion of the rights granted
hereunder by ATOMOS.
ATOMOS reserves the right to terminate this license without prejudice to
any additional recourse ATOMOS may have against you if you violate any
of its terms and conditions.
EXCEPT AS STATED IN THIS WARRANTY, ATOMOS, IT’S VENDORS,
AGENTS, RESELLERS AND DISTRIBUTORS DISCLAIM IN THEIR
ENTIRETY ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION ALL WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. THE REMEDIES OUTLINED IN
THIS WARRANTY ARE THE EXCLUSIVE REMEDY A CUSTOMER HAS
ARISING FROM DEFECTIVE GOODS WHICH ARE SUBJECT TO THE
WARRANTY.
ATOMOS DOES NOT WARRANT THAT THE GOODS WILL OPERATE IN A
MANNER WHICH IS ERROR FREE, OR UNINTERRUPTED. THE GOODS
ARE NOT INTENDED TO BE THE PRIMARY OR ONLY DATA STORAGE
DEVICE FOR DATA – CUSTOMERS ARE SOLELY RESPONSIBLE FOR
BACK UP AND PROTECTION OF DATA.
Atomos Ninja. User Manual V1.01
1
Introduction
Your Ninja comes with a standard 1 year warranty on all parts and
accessories. You can upgarde to a 3 year warranty on the Main Ninja
Unit alone (exluding TFT/LCD) by registering your Ninja online at
www.atomos.com/ninja/registration. This will enable us to let you
know about updates to the product and other important information
surrounding your purchase.
Ninja solves this by using Apple ProRes® compression. It’s much kinder
to your video, because it doesn’t compress it as much. By using 6, 8 or
10 to 1 compression instead of 20 or 30 to 1, its much better for editing,
because it doesn’t have lots of frames that have to be reconstructed from
other frames. Every frame is there in full.
It’s the fastest, and best-quality workflow possible today.
So, because it doesn’t compress as much, it needs more storage. And
- because of the plummeting price of hard disk storage - (it’s tens of
thousands of times cheaper than it was just fifteen years ago!) - the 2½”
disks used by the Ninja are very cheap. The cost of storage is no longer
an issue. Buying a disk for the Ninja is just like buying a tape - except
that with a disk, you have instant, random (“Non-Linear”) access to your
material, this eliminates the need for log-and-capture using a standard
capture card.
The reason that Ninja exists at all is because of the relentless march
of technology, and the way that this changes the economics of almost
everything. Most of all, though, it changes the way you use storage.
Ninja is easy to use, so this isn’t a long manual. We will issue software
updates for your Ninja on a regular basis. Please keep an eye on
www.atomos.com/ninja to see if any upgrades are due.
Built-in (or card-based) camera storage is a miracle of science; but that
doesn’t stop it being expensive when you use it with HD video. Video
takes up so much space — So you have to compress it.
We hope you enjoy your Ninja.
Thank you for buying an Atomos Ninja: your 10bit Production Weapon
for HDMI-equipped cameras. It’s going to transform the way you work
with video.
Ninja preserves the pristine uncompressed video quality from your
camera’s sensor by encoding it into Apple ProRes® directly. Then it goes
straight to the timeline of your NLE.
Even though MPEG compression like h.264 and MPEG-2 are very clever
technologies, they’re nowhere near perfect, and they certainly weren’t
designed for the rigours of editing.
®
Atomos Ninja. User Manual V1.01
2
1. What’s included
Your Ninja arrives as a complete system: you don’t have to add anything
except 2.5” storage media (you can buy additional packs of empty
Master Disk Caddies from your Atomos Reseller) and some cables to
suit your set-up like HDMI. All other parts necessary to use the Ninja
(including cables) are included in the carry case.
Here’s the complete list
Atomos does not sell storage and your package will not contain any
spinning disks or SSDs. You can buy these locally to keep running
costs as low as possible.
We recommend drives, please refer to Part 12 (Technical Specifications)
of this manual. For the most up-to-date information please visit:
www.atomos.com/ninja/HDDSSDSupport.pdf
• Ninja body (the Ninja itself, with touchscreen,
inputs and slot for Ninja disk caddies)
• 2 x empty Master Disk Caddies + 8 Screws for fixing disks
• Master Caddy Docking Station with
a. USB 2 & 3 Cable Under dock
b. Firewire Cable Under Ninja body
c. USB 2.0 power cable under dock for
extra USB power when required
• Battery Charger with Power Supply Unit located underneath
• 2xAtomos 7.4 V 2600milliAmp-hour(mAh)Batteries
• Ninja Carry Case
• Ninja Quick Start Guide (not pictured)
Atomos Ninja. User Manual V1.01
3
2. What you also need
2 ½” Disk Drives
These are the raw storage medium for Ninja.
You can use either traditional “spinning”
disks, or the new solid state ones. Choose
spinning drives if your Ninja is going to be
attached to a tripod or if it is not going to be
subject to excessive vibration. For harsher
conditions, choose a solid state drive.
Which drives should you use?
There are so many drives available, and new models appear all the
time. Speed and reliability are the main factors.
Some tips on working with disks
• Disk drive data rates tend to be given in megaBYTES per second, and
codec data rates are normally given in megaBITS per second. It’s very
easy to get confused. But there’s no need to be, because all you have
to do to convert megabits to megabytes is divide by 8. So if you’re
recording at 220 megaBITS per second, that’s going to result in 220/8
megaBYTES per second, which is 27.5 megaBYTES per second.
• To see what works for you, you may want to start working with
relatively fast drives 7200 RPM, and then try slower ones 5400 RPM.
This gives you a frame of reference for comparison. Just remember
that the higher the bitrate of the Apple ProRes® you’re using, the faster
the drive needs to be.
Solid State Drives (SSDs)
These are Flash memory devices that come in the same form-factor
as 2 ½” disk drives, and they are fully supported by the Ninja. See the
section below about when you should consider using SSDs. We only
recommend Intel SSDs at this stage as we have had unreliable results
from all other drives.
Mechanical Shock and Vibration
Here are some things that you should bear in mind when using
spinning disks:
• Even though spinning drives can withstand substantial shocks when
they are not in use, they are more vulnerable when running. Harsh
treatment that may not actually damage the drive may interrupt
recordings at a much lower level of severity. We recommend that you
experiment with your drives by testing them in the conditions that you
normally work in.
• Spinning drives have a gyroscopic effect that you will feel faintly if you
rotate the Ninja up or down or from side to side. They are particularly
sensitive to this type of motion. If you do this too quickly while the drive
is spinning, you may get a small gap in your recording.
• Be very gentle when changing batteries if you are recording. Practise
this manoeuvre so that you are able to do it smoothly. It is always
better to do this in-between takes.
• Do not bang or jolt the Ninja while recording. Gentle and cushioned
movement may be OK.
• You will find enormous differences in the ability of drives to withstand
shock and to continue recording during vibration and movement. As
we receive reports of drive durability and reliability, we will post them
on www.atomos.com
• Your Ninja is able to detect when the drive is under stress and it will
recover from any break in a recording by waiting until the drive is ready
to continue, and then resuming from that point. If frames have been
dropped because of shock or vibration, a “Skippy” Kangaroo symbol
will appear on the home screen on the Ninja, just above the disk
capacity indicator. This means that you will not normally have to restart
the Ninja, even if a recording has been interrupted by mechanical
disruption to the disk drive. (see Recording and Monitoring: Atomos
Anti-shock Technology for more information)
Hard disks are precision mechanical devices that need to be handled
carefully. You will be using the same type of drives that are normally used
in notebook computers, and you can use this as a guide to whether you
need to use mechanical drives or Solid State ones for any proposed
projects. If you think a particular usage scenario would be suitable for a
notebook computer, then it will probably be OK for a mechanical drive
inside a Ninja. If you think the drive inside your notebook might suffer
damage, then don’t use a mechanical drive.
Taking into account most usage scenarios, we think that mechanical
disks will be suitable in the majority of cases. Spinning disks are most
sensitive when they are rotating. It is obviously best to avoid dropping
them but many disks now have a “drop detector” that will lock the most
fragile mechanical parts in place and protect them from surprisingly hard
knocks. We recommend that if you want to experiment with this, you do
so with a drive that doesn’t contain the day’s shoot!
We can’t give rigid guidelines because there are so many different kinds
of drives, each with different mechanical properties. You may even find
variations between drives of the same type.
Backing up and archiving
What we have found is that mechanical drives are suitable for most
purposes that don’t involve harsh vibration or mechanical shocks. They
will be perfect for tripod-mounting, and also for the majority of hand-held
work. We would advise against hard-mounting them on moving vehicles
(but they would probably be OK if cushioned against the body of the
camera operator) and we would not advise using mechanical disks if
there is a likelihood that they might be dropped onto a hard surface.
Remember that no storage medium, including tape, optical disks,
spinning disks and flash memory, is completely immune from failure. You
should bear this in mind when deciding how to manage your recorded
content. At the very least, you should consider the consequences for you
and your business if your storage medium were to suffer from a sudden
failure, and you should back up your content accordingly. Hard drives
that you can use for archiving are becoming increasingly affordable. You
may find that it is completely feasible for your to keep your master Ninja
disks on a shelf (just like tapes!), and, as a backup, store copies on large
hard drives, RAID arrays or Network Attached Storage (NAS).
Atomos Ninja. User Manual V1.01
4
2. What you also need cont.
HDMI cables (not included)
There’s a lot of mythology about
HDMI cables. Most people can’t
tell the difference in picture quality
between expensive ones and
cheaper ones. There shouldn’t be
any difference if as long as all the
digits going through the cable arrive
at the other end. And yet some
supposedly “top end” cables can
cost hundreds of times more than you necessarily have to spend. It is
rare to get a cable that is bad enough to affect the picture, but keep in
mind that the longer the cable, the more likely it is to cause problems.
That’s completely different to the type of use they will get with the Ninja,
when they will be moved all the time and need to be strong but flexible.
Some of the cheaper HDMI cables might work properly but are almost
completely inflexible.
Flexible cables will put less strain on the HDMI sockets on your camera
and on your Ninja - but, in any case, it is worth considering some kind
of cable management (cable ties or clips) near each HDMI socket especially since HDMI is not a “locking” connection.
Some cameras and camcorders use a “mini” HDMI connection to save
space. Cables with a mini connection at one end and a standard one at
the other end are freely available.
There is at least one good reason for spending a bit more on an HDMI
cable: the physical quality.
If the HDMI cable is removed while recording the “Skippy”
image will also be displayed. To remove touch skippy and he
will disappear ready for his next notification.
HDMI was designed as a living-room standard. So most cables are
designed to be fitted behind TVs and rarely moved.
Refer to Part 8: Atomos Anti-skip Technology for more
information about “Skippy”.
Atomos Ninja. User Manual V1.01
5
3. Mounting disks in the Master Caddy
Mounting drives in the Master Caddy
This is simplicity itself. Just insert the disk into the caddy, and secure
with four screws. The caddy is light and the disk just needs to be held
securely. Don’t over-tighten the screws. There are no connections to
make because pushing the caddy into the Ninja or the Docking station
makes all the connections for you.
Spinning disks and SSDs are very sensitive to damage from static
electricity. Please observe all the usual precautions when handling them,
especially DO NOT EVER touch the exposed SATA connector as
static electricity may be harmful to your disk.
The Master Caddy can’t be inserted the wrong way round. Always make
sure that the disk connector faces the slot in the Ninja. You have to be
quite firm to push the Master Caddy into place, but don’t push too hard,
just in case something isn’t set up or aligned properly. There is very little
that can cause problems and the most likely thing is that the Master
Caddy isn’t properly flush with the drive inside. A quick visual check will
confirm this.
1
Carefully assemble the
Master Caddy and disk
Insert screw
Align all parts
2
Insert screw
Ensure all 3 parts aligned
and insert 4 x screws (supplied)
Do not over-tighten screws or
alignment can not be guaranteed.
We suggest squeezing the corners
together near the screw you are
tightening for optimal fit.
Atomos Ninja. User Manual V1.01
6
4. Connecting the Ninja and powering up
Batteries
Battery number 1
Gently slide down into
battery slot/s and lock
into position.
Push latch to release
battery
The Ninja is a battery powered device, and has a special feature to
ensure that you never have to interrupt a recording to change a battery.
We will come to this shortly.
Like all batteries, you will need to take care of them. Make sure that you
don’t short circuit the connections because this can result in very high
currents that can damage the cells and could pose a fire hazard.
Charge new batteries before using them. The supplied Ninja charger can
charge two batteries simultaneously. There are four red LED indicators for
each battery. This will show the approximate stage the charging process
has reached.
Batteries do not charge in a linear way. At first they charge very quickly,
and then the rate slows down to a trickle. While charging, one or more
red lights will blink. When 90% charge is reached, all the lights will flash.
It is perfectly OK to use the batteries at this point and we recommend
stopping at this stage for the longest battery life. If you leave the
batteries on charge after all four lights are flashing, the charger goes
into trickle charging mode for the final 10%. Eventually, when trickle
charging is complete, and the batteries are at 100% charge, all the
lights will go out.
for the first battery. This is effectively your
Always use battery slot
primary battery and the Ninja will not start without it. Battery slot No.2 is
the secondary or back-up battery and is not marked. Once the Ninja has
been started from battery slot No. 1, it will operate on battery slot No. 2
alone. No. 1 is only required for start up.
To insert the batteries, gently slide them down into the slot and lock
them into position. To remove a battery, push the latch to release it. Each
battery has its own latch, which is located to the right of batter No. 1 and
to the left of batter No. 2 as you look at the back of the Ninja. Pull the
latches towards the batteries to release them.
Ninja batteries are held in place very tightly because they are on the
outside of the device and there has to be no possibility whatsoever
that they could work loose, so you will have to be quite firm with the
battery latches. We suggests that you familiarise yourself with the force
required to remove the batteries so that you can do this quickly in the
field. Make sure that you hold the top and the bottom of the battery
when sliding it off to avoid dropping the battery when it is released from
the main unit.
The Ninja introduces an Atomos technology called Battery Looping for
continuous power. When power is running low on one battery, the Ninja
will automatically switch to the second battery, you can remove one of
the batteries and replace it with a fully charged one. Ninja will continue to
operate as you do this. You can continue this process indefinitely.
Ninja Battery Looping circuit will not operate if an AC adaptor is
attached. You can purchase a Sony NP Series 8.4V AC adaptor (used
by Sony Cameras) that have the same NP series battery plate.
WARNING: Do not connect batteries or AC Adaptors rated at greater
than 8.4 volts. The Ninja will power off if it senses excessive voltage.
AC Power Adaptor
The Ninja does not come with an AC power adaptor, however there are
AC cable versions of these batteries which connect to an AC adaptor to
give mains power to the Ninja. Sony and other manufacturers make such
plate AC adaptors for the NP Series battery plates the Ninja uses.
The AC adaptor must not deliver over 8.4 Volts to the Ninja or the unit
will shut down due to over voltage.
When the AC adaptor is present, BATTERY SWITCHING AND
LOOPING IS DISABLED!
Atomos Ninja. User Manual V1.01
7
4. Connecting the Ninja and powering up cont.
Turning ON power to the Ninja
The power on/off button is located on the right hand side of the unit (as
you look at the screen). Momentarily press the circular button on the
right side of the Ninja as you look at the screen to power up the unit.
After about a second, you will see the Atomos logo, and then the Ninja
Home Screen.
Turning OFF power to the Ninja
To turn the unit off, press the on/off button for four seconds, or touch
menu on the home screen, and then press the red Power off icon
for 4 seconds the icon will go white when touched to indicate activation
of the button . The unit will then power off.
On/Off
Turning OFF power via touchscreen
menu
power off
Four seconds can seem like a long time! We’ve made it this way to
make absolutely certain that the Ninja can’t be turned off accidentally.
5. Ninja connections
HDMI
Connect camera
to Ninja
using HDMI cable.
Audio
LANC Remote
Optionally control the Ninja using LANC
remote control connected here (use 2.5mm
TRS/ 3-pin plug)
Share remote control with other devices
(loop thru) by connecting them to the
second LANC connector.
Stereo Line In
Stereo Line Out
or Headphones
HDMI: The video input to the Ninja is HDMI. This is a standard,
Audio: There is a 3.5mm Stereo Line In socket for recording audio in
full-size connection, but you may find that your camera or camcorder
has another type. A common variant is the Mini HDMI connector.
Whichever version you have, it is easy to find cables with the appropriate
connectors at each end.
sync with incoming video. Depending on your set-up, you may find that
this gives you better results than the microphone on the camera.
LANC Remote: You have the option of controlling the Ninja remotely
using the LANC remote control protocol. The Ninja has a LANC input and
a LANC loop-through connector to allow you to chain LANC-controllable
devices together.
You can switch between Analogue Audio Line In and HDMI as your audio
sources in the user interface, where you can also adjust the analogue
audio input level.
There is also a 3.5mm output that doubles as a Line Out or Headphone
Out, which has it’s own independent level control in the user interface.
Atomos Ninja. User Manual V1.01
8
6. Other physical features
Master Caddy Slot
On the left hand side of the unit (as you face the screen) is a slot
for Ninja Master Disk Caddies. To insert a caddy, gently push until
it clicks into position.
Release and remove Master Caddy
To eject it, use the latch on the right hand side of the Ninja as you
look at the screen. (pictured right)
The Master Caddy is hot-swappable, so you can do this at any
time - even while the unit is turned on. But don’t do it while
recording or you will get a corrupted file that may be unplayable.
Release
latch
Ninja Master Disk Caddies are held in place firmly. Push
the latch upwards and grip the protruding part of the Ninja
Master Disk Caddy at the top and bottom, pulling strongly
but carefully. You may want to practise this manoeuvre a few
times until you are completely familiar with the process.
Screw mounts
The Ninja features standard tripod screw mounts on the top
and bottom of the unit, allowing you to configure your recording
setup various ways.
¼” Screw mount top
¼” Screw mount base
Atomos Ninja. User Manual V1.01
9
7. Using the Ninja
Using the Ninja
The User Interface in detail
The Ninja is controlled via an intuitive touchscreen interface. There are
large, obvious controls for Record, Play, Monitor, and Menu, as well as
the following information:
Even though the Ninja is an extremely sophisticated and technically
advanced device, we have taken a minimalist approach to the interface.
We’ve only included controls that you really need. This is important in
a device that has to be ready for use at all times and must therefore be
simple to operate while in use.
• Current input format and status
• Apple ProRes® variant currently in use
• Remaining battery power
Ninja’s touchscreen
• Which of the two batteries is currently active
Ninja features a very high quality video touchscreen. Most of us are now
familiar with the idea of touchscreens, but there is an important difference
between Ninja’s screen and those you might find on a smartphone.
• Headphone/Line Out volume
• Audio Input Level meters
• Remaining Recording time on Disk
• Timecode
Watch out for any items on the screen that are marked by a
small blue arrow. If you touch these items you will be taken
to other options depending on context. If you touch them
sequentially, you will cycle through related options
A large blue arrow in the top right of the screen will
take you out of lower-level menus back to the main
control screen
Ninja’s screen is pressure and touch sensitive. It takes more than a
glancing brush of a finger to trigger the screen. For some applications,
(like dragging and dropping) this would be a disadvantage, but for the
Ninja it is an important feature, because if the screen was too sensitive,
it would be easy to accidentally trigger Ninja operations, potentially
interrupting a recording, for example.
With the Ninja screen, you have to firmly push the screen for an
instruction to register. This gives a very positive feel to the device and
confidence that commands won’t be given in error.
Be definite and deliberate in your pressing on icons on the screen and
the Ninja will be very responsive. Remember this is not a capacitive
touch device like many Smart Phones; holding contact with the icon for a
millisecond will ensure accurate and rapid response.
The Home Screen
This is the screen you see whenever your are not in a sub-menu or
function, and it is the first screen that the Ninja boots into when you turn
it on. There are four brightly coloured icons labelled Rec, Play,
Mon and Menu. We’ll deal with these in turn.
Input (Codec used
for recording)
Battery power
remaining
Current video input
format and status
Currently
active battery:
1 or 2
Headphone Line
Out volume
Audio input
level meters
Recording time
remaining
Atomos Ninja. User Manual V1.01
10
7. Using the Ninja cont.
The Play button will be dimmed and disabled
if no media to play back from is available i.e. the
disk has been ejected.
Rec (Record)
This is the icon you touch to begin a recording. Touch it again to stop a
recording. While recording the Rec icon changes to a Stop icon. Once
your recording has started you have the option to touch the Mon icon to
view the signal you are recording.
Mon (Monitor)
Standby
Pressing this icon connects the incoming video signal to the screen, so
that you can use the Ninja as a field monitor. More about monitoring in
the next section.
Standby
Recording
NO INPUT
The Mon icon is dimmed and unselectable if there
is no valid video input.
NO INPUT
The Rec icon is dimmed and disabled if
there is no valid video input OR if the disk is
full. There is no point in being able to make a
recording if there is no incoming signal or if
there is no storage available.
Play
Touch this icon to play previously recorded clips. Ninja uses a Scene,
Shot and Take convention to organise clips (we’ll look at this in
Menu
Pressing this takes you into a number of options which we will
explain here:
Standby
the next section) and you can navigate around the stored shots quite
easily using this. When you touch the Play button, you are taken to the
navigation screen for the clips.
Standby
MENU
NAVIGATION
In the Play navigation screen, select the shot you want to play back, and
press the Play button on the right of the screen, which is only visible if
you have selected a valid clip for playback.
Atomos Ninja. User Manual V1.01
11
7. Using the Ninja cont.
Scene & Shot
Allows you to arrange your recordings. Just touch Scene
& Shot and you will be taken to a screen where you can
chose which Scene and Shot you wish the clip to be known
by. The Takes will automatically start from 1 and increment
up upon start and stop recording.
Date & Time
Allows you to adjust the date and time shown by the clock
and calendar in the Ninja. Touching the Date & Time
takes you into the Date and Time Screen. At the top of the
screen is the date and the time of day. The month, day
and year are selectable by touching them, at which point
a scrollable list of dates, months or years will show below,
depending on which option has been selected. To enter a date, for example, begin by touching the month
at the top of the screen, and then select the required month
from the list below. Then touch the day, and then the year,
selecting the required value from the list below.
Setting the time is done in exactly the same way.
Date formats (i.e. dd-mm-yyyy or mm-dd-yyyy) are
selectable on the right of the screen. Just keep touching
the date format icon until it shows the format you
want to use.
Display Options
Allows you to modify the brightness of the screen. You are
presented with a horizontal slider. Touch it anywhere on it’s
length to increase or decrease the brightness of the display
or you can slide up and down the blue bar.
Ninja Info
Shows the software version of your Ninja device. This will
be useful if you ever have to speak to Atomos technical
support or a support agent from your reseller.
Smaller controls and indicators around the Home Screen
There are a number of smaller controls that double-up as indicators
around the Home Screen.
Input
At the top left of the screen is not actually a control but will change to
display information about the signal being input to the Ninja at the time.
If there is no input, it will say No Input. When a valid signal source is
connected, the display will change to (for example) 1080i50.
ProRes Format
At the top middle of the screen shows which version of ProRes® you are
using. You can change between versions (LT, HQ and 422) by repeatedly
touching the indicator.’
Battery Indicator
Shows whether you’ve got one or two batteries connected. Orange
indicates which battery is being used at any given time. Touching the
Battery Indicator takes you to the Batteries screen
where you can closely monitor the status of the batteries with a display
of the voltage levels on each device. The Battery Indicator
is made from two small Battery icons, which will flash when it’s
corresponding battery is running low.
Batteries Screen
The battery screen indicates the active battery in orange and the level of
each battery is shaded in ¼ increments. In this case Battery 1 is full and
active and battery 2 is ¼ depleted.
Power Off
Turns the Ninja off. You need to press Power Off for four
seconds. Alternatively, you can press the physical On/Off
button on the right side of the Ninja for four seconds to
achieve the same result.
Time Code
allows you to chose between dropframe timecode and
non-dropframe timecode.
Remember that pressing a large blue arrowhead will always take you
back to the previous menu you were in.
Warning: If both of the Nnja batteries are running low, the unit
will turn itself off. You will know this will hapen because the Ninja
will flick to the battery screen every 10 seconds indicating you are
about to run out of power. To avoid this always have one replenished
battery on the Ninja unit.
Auto Switching/Manual Switching
The Ninja will automatically switch to a new battery when the current
battery is depleted. You may also switch between batteries at any
time by pressing on that battery icon. The new active battery will then
turn orange. You may need to use this if you have for example 3 hours
recording but only 2.5 hours of battery in one battery, in which case you
would change to a freshly charged one.
Atomos Ninja. User Manual V1.01
12
7. Using the Ninja cont.
Storage Capacity Indicator
Headphone Monitoring Level
is in the bottom right of the screen. When a disk is inserted, the
Located in the bottom left corner of the screen, just above Audio In.
Touching this brings you to a page where you can select whether to
monitor the incoming Analogue audio signal or the Digital signal on the
HDMI input. You can also adjust the headphone monitoring level by
touching the slider control to set the required headphone output level.
Storage Capacity Indicator will show the recording
capacity of the drive in hours minutes and seconds, based on the
currently selected version of ProRes®, which of course, will determine the
recording bitrate.
Touching on the Storage Capacity Indicator will take you
to the Media information and format screen. The Media Information
indicates the drive you have present, in this case a Hitachi 500GB
spinning disk.
Touching Format HDD/SSD will format the drive inside the Ninja.
A confirmation screen will give you the choice to continue or cancel the
process.
The Ninja uses a high quality headphone amplifier that is quite
powerful. This is so that it can easily power all types of headphone
device. So you need to be careful that you do not have the level set too
high, as excessive levels could be harmful to your hearing.
Audio In
Audio In is in the bottom left corner of the screen, just below
Headphone Monitoring Level. There are four small
squares, each of which represents an audio input. Inputs 1 and 2 are the
two analogue inputs, and inputs 3 and 4 are the two digital inputs which
come from the HDMI source. These four squares also act as approximate
level and “signal present” indicators. Touching the Audio In icon
takes you to the Audio In page, where you can choose to record
from either HDMI or the analogue inputs, or both, for a four-channel
audio recording. There is also a slider to control the analogue gain.
The Nina file system is FAT32. You must format each disk with the
Ninja and not your computer.
It is not possible to vary the gain if the signal input is from the
HDMI connection because this is digital and is embedded in
the signal. You can usually adjust this from the camera, see
your cameras manual for operational details.
Atomos Ninja. User Manual V1.01
13
8. Monitoring and Recording
Connect to Input
Before Recording
As soon as you connect an input source of a type that is supported by
the Ninja, you will see the Record and Monitor icons go solid and
light up.
Check that there is a valid signal by noting the input display and
checking that the Record and Monitor icons are lit up. Then
press the Monitor to check the integrity of the source feed. After this
press the Record button, and the recording will start. Notice that the
Record icon changes to a Stop icon when in record mode. To end
the recording, press Stop.
If you want to use the screen as a field monitor, just press Mon.
To record the incoming signal, press Rec. To play back previously
captured footage, press Play.
NO INPUT
RECORDING
READY TO RECORD
MONITORING
The Ninja has a high-quality video screen that adjusts to the scan
frequency of the incoming signal, for a smooth, accurate display.
Organising Material on the disk
Ninja uses a simple, familiar convention to organise your material. Clips
are stored under a hierarchy of Scene, Shot and Take. You can
think of this as being like a folder structure. Choose a scene number and
a shot number, and the Ninja will automatically increment each take.
The actual process of navigating through the organisational structure is
simple. To investigate it, touch Menu and then Shot and Take. You
will be taken to a screen that has Scene, Shot and Take written
across the top. To select a scene, select Scene in the top left hand
corner of the screen. Scene will be underlined and you will see a list of
scene numbers that you can chose by touching them. When you make
a selection, the number you’ve chosen will appear above the line in a
slightly larger size.
Do the same sequence to select a shot and a take. Then you’re ready to
record. If you don’t have time to set this up, the Ninja will record anyway,
putting your most recent footage in the shot folder that you last used.
This is a system that is very easy to understand once you have used it.
Atomos Ninja. User Manual V1.01
14
8. Monitoring and Recording cont.
Atomos Anti-Shock Technology
Spinning disks are very reliable in a controlled environment where
movement and vibration are minimal and within the capabilities of the
devices. They are ideal for low-cost recording, but will suffer reduced
performance if they are jolted or receive a sudden impact.
Should one of these events occur, the Ninja will sense the hard disk
slowdown. If there is a break in the recording it will detect the number of
frames involved and will then continue to record when it is safe to so so.
This means that even if you suffer a momentary break in your recording, the
video capture will continue without any intervention from you, the user.
It is obviously important for you to know that you have suffered from an
interrupted recording and the user interface will display a warning (in the
form of a Kangaroo sign) clearly above the disk-capacity display on the
main screen.
If you find you are working on a very active project where you are seeing
a lot of “Skippys” then you probably need to switch to SSDs, and only
use spinning disks for gentler environments.
“Skippy”
warning
To remove “Skippy” warning, simply touch the icon and he will
disappear ready for his next notification.
9. Connecting and Editing
To access and edit your recorded material, connect the Master Caddy
Docking Station to a Mac® or Windows® editing workstation via USB 2.0,
USB 3.0 or FireWire® 800 port.
Eject the Master Caddy from your Ninja and insert it into the Docking
Station. After a short wait, the recorded video will be accessible to the
target computer via a standard disk (FAT) file system.
The Master Caddy Docking Station is a sophisticated device
supporting three different data interfaces: Firewire 800, USB 2 and
USB 3. Note that when using the Master Caddy Docking Station you
may need to connect an additional USB cable to the 5v power input.
This is because when it has to power a disk drive and its interface
electronics, the Docking Station may consume more power than is
available from a single USB port. We supply you with a USB to 5v
Power Supply socket for this purpose
Optional
power input.
May be required
when using USB.
Firewire®
USB
Insert
Master
Caddy
Atomos Ninja. User Manual V1.01
15
9. Connecting and Editing cont.
Importing Ninja footage into Final Cut Pro
You can import Ninja footage into Final Cut Pro (FCP) in just a few
simple steps.
You’ll see the folders in the Ninja drive. Select the folder containing the
footage you want to import:
First, connect the Ninja Docking Station to your Apple Mac using the
Firewire 800 port (USB 2.0 will also work). Insert the Ninja Master Caddy
containing the disk with your footage into the Docking Station and you
will see the drive appear in your Finder window.
Start FCP and open your project (or start a new one).
The screen will look like this:
Click on Choose and go back to your FCP project window:
Go to the File menu and select Import > folder:
Your Scene, Shot and Take folders now appear in the project window,
ready for use in your FCP project.
FCP will show you a “browse” window. Look for the Ninja drive, and
click on it.
Atomos Ninja. User Manual V1.01
16
10. Software updates
Updating ATOM-OS (Firmware)
Problems when installing ATOM-OS (Firmware)
Most modern electronic and digital systems are a combination of
hardware (the physical “object” or “thing”) and software (the program
running inside the device that allows it to operate).
Very occasionally, the firmware
update process can go wrong.
This might be because of an
incomplete or corrupted download,
or any number of other unlikely
but possible causes. With many
devices this can cause major
problems, with distinct possibility that your device could become
“bricked”: as unresponsive as a dense lump of building material.
The software inside devices like the Ninja is often referred to as
“firmware”, which simply means that it is used by the device to run itself,
as opposed to being like an “application” you might see on an iPad or on
your computer. The Ninja’s firmware is called ATOM-OS.
• Go to www.atomos.com/ninja/downloads
• Find the latest software for your Ninja
• Download it onto your computer
• Connect a Ninja drive to your computer using the docking station
• Copy the file to the drive
• Insert HDD/SSD while the Ninja is off
• Turn on and the NInja will find the dowload and install
We want you to be able to upgrade your firmware with confidence, so
we have built-in a recovery mechanism in case your Ninja should ever
“brick” itself.
All you have to do is press and hold the on/off button for 10 seconds.
If you do this your Ninja will revert to it’s factory condition, and you will be
able to retry the firmware update later (taking due precautions to identify
and remove possible reasons for the failure of the previous attempt).
Please make sure your batteries have plenty of charge and that you
do not interrupt your Ninja while its firmware is upgrading. You will see
a randomised colour-bar display on the screen top and bottom of the
screen while updating is taking place. When it is finished, it will turn
off. When you turn it on again, it will be running the new firmware.
Atomos Ninja. User Manual V1.01
17
11. Technical Specifications
Ninja Main Unit
Dimensions (without Batteries)
115(W)x87(H)x41(D)mm
Operating Power
approx 6.3W (TFT max brightness, recording ProRes® HQ to WD 7200 rpm Scorpio Black 500 G drive)
approx 3.0W (TFT max brightness, monitoring only)
Batteries
2 x Small
7.4V 2600mAh – recording time*
5 hrs HQ; 7 hrs 422; 9 hrs LT
7.4V 5200mAh - recording time
2 x Medium
10 hrs HQ; 14 hrs 422; 18 hrs LT
7.4V 7800mAh - recording time
2 x Large
15 hrs HQ; 21 hrs 422; 27 hrs LT
* at 1080i60 extreme detail video; better at lower rates or with typical video
Automatic and manual switchover of battery for continuous operation
Colour 16:9 TFT Touchscreen
Size
Resolution
480x270
Aspect Ratio
16:9 Native / 4:3 Letterbox
4.3” diagonal
Video Input
HDMI Uncompressed
Supported Input Formats
HD 1080i60, 1080i59.94, 1080i50, 1080p30*, 1080p25*, 1080p24, 1080p23.98, 720p60, 720p59.94, 720p50, SD 480i, 576i
* from firmware v1.1
Recording Time
HDD
CODEC
300GB
500GB
750GB
SSD
128GB
256GB
ProResHQ
3hrs
5hrs
7.5hrs
77min
2.5hrs
ProRes422
4.5hrs
7.5hrs
11.5hrs
2hrs
4hrs
ProResLT
6.5hrs
11hrs
16.5hrs
3hrs
4.5hrs
all video input formats supported
Audio Input
HDMI 2 Channel Embedded
Line In 2 Channel Line Level Audio. Analog gain adjustment
Audio Output
2 Channel 0.5W Balanced Headphone or Line level output
LANC
LANC In and Out Loop for integration with Camera LANC and Accessories
LANC Loop feature
Master Caddy Specs
Dimensions
75x105x12mm
Supported Storage
2.5” SSD or HDD minimum 5400rpm
Standard 9.5mm height or slimmer drive supported
Master Caddy Dock
2.5” SATA to Firewire 800, USB2.0/3.0
Supported Computers
Mac - All MacBook, MacPro, iMac and MacPro Models
(for SATA adapter)
Windows All USB2.0/3.0 compatible Notebooks, and Desktops.
Note: Apple ProRes® Quicktime Application required to run ProRes® on Windows
Applications
Final Cut Studio – All Apple ProRes® supported versions
Quicktime Mac and Windows
Accessories
Universal Battery Charger 110-240V / Tripod Screw mounts and adaptors / Protective cases and Travel Bags
SSD / HDD Usage Notes:
With spinning drives, you need to be careful in handling when recording. The drives will generally stand light/medium occasional bumps without problems,
and the Ninja has an anti-shock buffer. However, spinning drives are not suitable for use in high vibration or movement environments, for example if the
Ninja is strapped to the side of a motor bike.
With spinning hard drives, use a new drive, or one that has very little usage. Do not use old drives. Do not use drives that have been dropped.
On all drives, when handling, keep fingers away from the SATA connector at all times, as static electricity can damage the electronics inside.
Atomos Ninja. User Manual V1.01
18
Atomos Ninja
User Manual
Version 1.0 – March 2011
Sales & Technical Support
Atomos – Website: www.atomos.com | Sales: [email protected] | Support: [email protected]
at omos.com
© Katana Ltd Hong Kong trading as Atomos under license Sept 2010. All trademarks are the property of their respective owners.