Download Hardware Manual - RTD Embedded Technologies, Inc.

CM17215HR 100Mb/s Fiber
CM17212HR 10/100Mb/s UTP
PC/104-Plus Dual Ethernet
utilityModule
User’s Manual
ISO9001 and AS9100 Certified
BDM-610020066
Rev. E
CM17215HR 100Mb/s Fiber
CM17212HR 10/100Mb/s Twisted Pair
PC/104-Plus Dual Ethernet utilityModule
User’s Manual
RTD Embedded Technologies, Inc.
103 Innovation Blvd.
State College, PA 16803-0906
Phone: +1-814-234-8087
FAX: +1-814-234-5218
E-mail
[email protected]
[email protected]
web site
http://www.rtd.com
Revision History
Rev. A
08/07/2007
Initial Release
Rev. B
09/11/2007
Rev. C
Rev. D
02/24/2009
12/07/2010
Rev E
3/4/2011
Added references for 82551IT Ethernet Controller
Added chapter on using the module
Added chapter for additional information
Updated PC/104-Plus specification information, and connector pinout
Added pin out information for CN5 and CN8
Updated Link LED description for new PCB. Removed Fiber Interface
Considerations (CM17215 Only)
Corrected port 1 LED descriptions
Published by:
RTD Embedded Technologies, Inc.
103 Innovation Blvd.
State College, PA 16803-0906
Copyright 2010 by RTD Embedded Technologies, Inc.
All rights reserved.
The RTD Logo is a registered trademark of RTD Embedded Technologies. cpuModule and utilityModule are
trademarks of RTD Embedded Technologies. PC/104 is a registered trademark of PC/104 Consortium. All other
trademarks appearing in this document are the property of their respective owners.
Table of Contents
CHAPTER 1
INTRODUCTION ...........................................................................................................................1
ELECTRICAL SPECIFICATIONS .....................................................................................................................................1
MECHANICAL SPECIFICATIONS ...................................................................................................................................1
ENVIRONMENTAL .......................................................................................................................................................1
CHAPTER 2
CM17212/17215HR LAYOUT ........................................................................................................2
FINDING PIN 1 OF CONNECTORS .................................................................................................................................2
COMPONENT LOCATIONS ...........................................................................................................................................2
LIST OF CONNECTORS AND SWITCHES ........................................................................................................................4
PC/104 ISA BUS CONNECTORS, CN1 AND CN2 .........................................................................................................5
PC/104-PLUS PCI CONNECTOR, CN3 .........................................................................................................................5
MT-RJ FIBER ETHERNET, CN6 AND CN9 ..................................................................................................................5
PCI BOARD SELECTOR ROTARY SWITCH, SW1..........................................................................................................5
STATUS LEDS ............................................................................................................................................................ 6
CHAPTER 3
INSTALLING THE UTILITYMODULE ..................................................................................7
RECOMMENDED PROCEDURE .....................................................................................................................................7
CHAPTER 4
USING THE CM17212/17215 .........................................................................................................8
DRIVER SUPPORT .......................................................................................................................................................8
CHAPTER 5
ADDITIONAL INFORMATION ...................................................................................................9
ETHERNET CONTROLLER ............................................................................................................................................9
FIBER INTERFACE .......................................................................................................................................................9
CHAPTER 6
RETURN POLICY AND WARRANTY ...................................................................................... 10
RETURN POLICY ....................................................................................................................................................... 10
LIMITED WARRANTY................................................................................................................................................ 11
Table of Tables
TABLE 1: LIST OF CONNECTORS AND SWITCHES ...........................................................................................................4
TABLE 2: UTP 10PIN DIL CONNECTORS CN5 AND CN8 .................................................................................................4
TABLE 3: CM17212 STATUS LEDS ............................................................................................................................... 6
TABLE 4: CM17215 STATUS LEDS ............................................................................................................................... 6
Table of Figures
FIGURE 1: COMPONENT LOCATIONS ON CM17215 ........................................................................................................2
FIGURE 2: COMPONENT LOCATIONS ON CM17212 ........................................................................................................3
Chapter 1 INTRODUCTION
This manual gives information on the CM17215 PC/104-Plus Dual 100Mb/s Fiber Ethernet
utilityModule and the CM17212 PC/104-Plus Dual 10/100Mb/s Fast Ethernet utilityModule.
This module provides two (2) independent Ethernet connections (Fiber – CM17215, UTP – CM17212).
Each channel is capable of operating through a MT-RJ fiber connector (CM17215) or a standard RJ-45
connector (CM17212).
Each channel of the CM17212/17215 utilityModule operates using its own Intel 82551IT PCI Ethernet
Controller. An onboard PCI-to-PCI bridge allows the two Ethernet controllers to appear as a single PCI
slot to the host computer. In the case of the CM17215, an Intel LXT973 2-Port Ethernet PHY Transceiver
provides the bridging to the fiber interface.
Electrical Specifications





Compatible with PCI Local Bus Specification Revision 2.2
Compatible with PC/104-Plus Specification Revision 2.0
5V Tolerant PCI Interface
Only requires +5VDC power
Power Consumption:
- CM17212: 1.7 W typical*
- CM17215: 4.6 W typical*
Mechanical Specifications


PCB Dimensions: 3.6 x 3.8 x 0.6" (90 x 96 x 16 mm)
Weight (mass): 0.22 lbs. (0.10 Kg)
Environmental


Operating Temperature: -40 to 85 C, 90% Humidity non-condensing
Storage Temperature: -55 to 125 C
* Typical power consumption is defined as both Ethernet connections plugged into a network with
moderate background activity.
CM17212/17215HR User’s Manual
1
BDM-610020066 rev E
Chapter 2
CM17212/17215HR LAYOUT
Finding Pin 1 of Connectors
The three possible ways to determine pin 1 on the connectors are:
1. A square white area silk-screened on the PC board
2. A square solder pad visible on the bottom of the PC board
3. A numeral 1 silk-screened near pin 1 on the top of the PC board
Component Locations
The figures below show switch and connector locations.
CN3: PCI Connector
LEDs for Fiber Ports
CN9: Port 0 MT-RJ Fiber
CN6: Port 1 MT-RJ Fiber
CN1: XT Bus
SW1: PCI
Rotary Switch
CN2: AT Bus
Figure 1: Component Locations on CM17215
CM17212/17215HR User’s Manual
2
BDM-610020066 rev E
Figure 2: Component Locations on CM17212
CM17212/17215HR User’s Manual
3
BDM-610020066 rev E
List of Connectors and Switches
Connector
Function
Dimension
CN1, CN2
XT/AT Bus Connector (pass-through)
64 + 32 pins
CN3
PCI Bus Connector
120 pins
CN9
Port 0 Fiber Connector (CM17215 only)
MT-RJ
CN6
Port 1 Fiber Connector (CM17215 only)
MT-RJ
CN7
Port 0 UTP (CM17212 only)
RJ-45
CN4
Port 1 UTP (CM17212 only)
RJ-45
SW1
PCI Board Selector Rotary Switch
Rotary Switch
CN5
Port 0 UTP (CM17212 only)
10 pin DIL
CN8
Port 1 UTP (CM17212 only)
10 pin DIL
Table 1: List of Connectors and Switches
Pin
1
3
5
7
9
CN8 Port 1
Name
Pin
RX1+
2
Term1
4
TX1+
6
Term2
8
frame1
10
Name
RX1Term1
TX1Term2
frame1
Pin
1
3
5
7
9
CN5 Port 2
Name
Pin
RX2+
2
Term3
4
TX2+
6
Term4
8
frame2
10
Name
RX2Term3
TX2Term4
frame2
Term1 is the output receive termination of Port 1
Term2 is the output transmit termination of Port 1
Term3 is the output receive termination of Port 2
Term4 is the output transmit termination of Port 2
Frame1 is separated from frame ground by solder blob B2
Frame2 is separated from frame ground by solder blob B3
(B2 and B3 are unpopulated by default)
Table 2: UTP 10pin DIL connectors CN5 and CN8
CM17212/17215HR User’s Manual
4
BDM-610020066 rev E
PC/104 ISA Bus Connectors, CN1 and CN2
Connectors CN1 and CN2 provide PC/104 bus connections. CN1 carries XT bus signals, and CN2 carries
additional signals for the AT bus. Refer to table 4 of the PC/104-Plus Specification Revision 2.0 for the
pinout of these connectors
Since the CM17212/17215 is a PCI device, the ISA bus connectors are simply pass-through connections.
Note:
Two locations on the bus have mechanical keying pins to help prevent misconnection of the
PC/104 bus. These keying pins are a part of the PC/104 standard, and we strongly recommend
you leave them in place.
If you have other modules without keying pins, we suggest you modify them to include
keying.
PC/104-Plus PCI connector, CN3
Connector CN3 carries the signals of the PC/104-Plus PCI bus. These signals match definitions of the PCI
Local Bus specification Revision 2.2. Refer to table 3 of the PC/104-Plus Specification Revision 2.0 for the
pinout of this connector.
MT-RJ Fiber Ethernet, CN6 and CN9
The fiber connectors on the CM17215 are male MT-RJ fiber transceivers (Avago AFBR-5903AZ). The
transmitter transmits using a 1300 nm surface emitting InGaAsP LED and the receiver receives using an
InGaAs PIN photodiode. It is designed to be used with Multi-Mode fiber. For other fiber interfaces,
contact RTD technical support.
Before installing a MT-RJ fiber into the connector, remove the protection plug from the connector.
Eye
Safety
Test Method
IEC 825 Issue 1 1993:11 Class 1
CENELEC EN60825 Class 1
Performance
Compliant per Avago testing under single
fault conditions
TUV Certification: LED Class 1
PCI Board Selector Rotary Switch, SW1
Since the utilityModule uses stack through buses, the only hardware installation you will need to do is to
place the module onto the PC/104-Plus or PCI-104 stack. To do this, you will connect the PCI and/or ISA
bus connectors on the CM17212/17215 to the respective connectors of your stack.
Before you can use this module you have to set the PCI board selector rotary switch located on the module
(SW1). If this module is the first module from the CPU module select ’0,’ if it is the second module select
’1,’ etc.
CM17212/17215HR User’s Manual
5
BDM-610020066 rev E
Status LEDs
The LEDs on the board are used to indicate status of the Ethernet ports.
Table 3: CM17212 Status LEDs
Port
Port 0
Port 1
DESCRIPTION
Diode #
Speed
 On = 100Mb/s
 Off = 10Mb/s
Link/Activity
 Off = No link detected
 On = Link Detected
 Flashing = Activity
Speed
 On = 100Mb/s
 Off = 10Mb/s
Link/Activity
 Off = No link detected
 On = Link Detected
 Flashing = Activity
D3
D4
D2
D1
Table 4: CM17215 Status LEDs
Port
Port 0
Port 1
DESCRIPTION
Link


Activity


Link


Activity


Diode #
On = Link Detected
Off = No link detected
D3
On = Activity
Off = No activity
D4
On = Link Detected
Off = No link detected
D1
On = Activity
Off = No activity
D2
CM17212/17215HR User’s Manual
6
BDM-610020066 rev E
Chapter 3 INSTALLING THE UTILITYMODULE
WARNING!
Like all equipment using CMOS devices, the CM17212/17215 must be protected from static discharge. Never
touch any of the parts except at static-free workstation. Use anti-static bag shipped with the CM17212/17215 to
handle the board
The following sections contain information on configuring the CM17212/17215 PC/104-Plus Ethernet
utilityModule. Please read the entire section before attempting to use the utilityModule!
Recommended Procedure
We recommend you follow the procedure below to ensure the stacking of the modules does not damage
connectors or electronics.
0
Turn off power to the PC/104-Plus system or stack.
1
Select and install standoffs to properly position the utilityModule on the PC/104-Plus stack.
2
Touch a grounded metal part of the stack to discharge any buildup of static electricity.
3
Remove the utilityModule from its anti-static bag.
4
Check to see if the keying pins in the PCI bus connector are properly positioned.
5
Check the stacking order and set the PCI Board Selector Rotary Switch, SW1.
6
Hold the utilityModule by its edges and orient it so that the bus connector pins line up with
the matching connector pins on the stack.
7
CAUTION:
Gently and evenly press the utilityModule onto the PC/104-Plus stack.
Do not force the module onto the stack! Wiggling the module or applying too much force
may damage it. If the module does not readily press into place, remove it, check for bent
pins or out-of-place keying pins, and try again.
CM17212/17215HR User’s Manual
7
BDM-610020066 rev E
Chapter 4
USING THE CM17212/17215
Driver Support
For Windows 2000/XP, the CM17212/17215 is supported by an Ethernet driver provided by Intel. A
copy of this driver is provided on the companion CD that is shipped with the board, and may also be
downloaded from the RTD web site (www.rtd.com). It is recommended that you frequently check the
RTD web site for updated documentation and drivers.
Under Linux, the Ethernet controller is supported via the e100 kernel module that is built into the
official 2.4 and 2.6 Linux kernels. Most modern desktop Linux distributions will automatically detect
the Ethernet controller and load the necessary drivers. Contact the vendor of your Linux distribution
for more information.
For other operating systems, the CM17212/17215 may be natively supported. Many operating systems
include support for the Intel 82551IT PCI Ethernet controller, which the CM17212/17215 is based on.
Your operating system vendor should be able to provide the necessary information.
CM17212/17215HR User’s Manual
8
BDM-610020066 rev E
Chapter 5
ADDITIONAL INFORMATION
Ethernet Controller
For more information on the Ethernet Controller used on the CM17212/17215, refer to the following
documents from Intel:

Intel 82551IT Datasheet

Intel 8255x Software Developer Manual
Both of these may be downloaded from Intel’s web site (www.intel.com).
Fiber Interface
For more information on the physical fiber interface, refer to the datasheet for the Avago AFBR5903AZ Fiber Transceiver, which can be downloaded from www.avagotech.com.
CM17212/17215HR User’s Manual
9
BDM-610020066 rev E
Chapter 6
RETURN POLICY AND WARRANTY
Return Policy
If you wish to return a product to the factory for service, please follow this procedure:
Read the Limited Warranty to familiarize yourself with our warranty policy.
Contact the factory for a Return Merchandise Authorization (RMA) number.
Please have the following available:
•
•
•
Complete board name
Board serial number
A detailed description of the board’s behavior
When returning the board, list the name of a contact person, familiar with technical details of the
problem or situation, along with their phone and fax numbers, address, and e-mail address (if
available).
List your shipping address!!
Indicate the shipping method you would like used to return the product to you. We will not ship by
next-day service without your pre-approval.
Carefully package the product, using proper anti-static packaging.
Write the RMA number in large (1") letters on the outside of the package.
Return the package to:
RTD Embedded Technologies, Inc.
103 Innovation Blvd.
State College PA 16803-0906
USA
CM17212/17215HR User’s Manual
10
BDM-610020066 rev E
Limited Warranty
RTD Embedded Technologies, Inc. warrants the hardware and software products it manufactures and
produces to be free from defects in materials and workmanship for one year following the date of shipment
from RTD Embedded Technologies, INC. This warranty is limited to the original purchaser of product and
is not transferable.
During the one year warranty period, RTD Embedded Technologies will repair or replace, at its option, any
defective products or parts at no additional charge, provided that the product is returned, shipping prepaid,
to RTD Embedded Technologies. All replaced parts and products become the property of RTD Embedded
Technologies. Before returning any product for repair, customers are required to contact the factory for an
RMA number.
THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCTS WHICH HAVE BEEN
DAMAGED AS A RESULT OF ACCIDENT, MISUSE, ABUSE (such as: use of incorrect input voltages,
improper or insufficient ventilation, failure to follow the operating instructions that are provided by RTD
Embedded Technologies, "acts of God" or other contingencies beyond the control of RTD Embedded
Technologies), OR AS A RESULT OF SERVICE OR MODIFICATION BY ANYONE OTHER THAN
RTD Embedded Technologies. EXCEPT AS EXPRESSLY SET FORTH ABOVE, NO OTHER
WARRANTIES ARE EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, AND RTD Embedded Technologies EXPRESSLY DISCLAIMS ALL WARRANTIES NOT
STATED HEREIN. ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES FOR
MECHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE
DURATION OF THIS WARRANTY. IN THE EVENT THE PRODUCT IS NOT FREE FROM
DEFECTS AS WARRANTED ABOVE, THE PURCHASER'S SOLE REMEDY SHALL BE REPAIR OR
REPLACEMENT AS PROVIDED ABOVE. UNDER NO CIRCUMSTANCES WILL RTD Embedded
Technologies BE LIABLE TO THE PURCHASER OR ANY USER FOR ANY DAMAGES,
INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS,
LOST SAVINGS, OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
PRODUCT.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, AND SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
CM17212/17215HR User’s Manual
11
BDM-610020066 rev E