Download Manual

Content
1. Declaration of Conformity.....................................3
9. Consists..............................................................11
15. Using several base units in one room.................16
2. WEEE-Declaration..................................................3
9.1. Add locomotives to consists.................................11
9.2. Running consists..................................................11
9.3. Removing a locomotive form a consist.................11
9.4. Deleting consists..................................................11
16. ESU Support......................................................16
3. Important Remarks - Please read this section first....3
4. Content of package..............................................3
5. Introduction – What can the Navigator do?...........4
5.1. System architecture................................................4
5.1.1. Handheld controller.............................................4
5.1.2. Base unit.............................................................4
5.1.2.1. Fan control.......................................................4
5.1.3. IR receiver...........................................................4
5.2. Controlling locomotives..........................................4
5.3. Data formats..........................................................4
5.3.1. Data format Motorola®......................................4
5.3.1.1. Range of addresses - Motorola®......................4
5.3.2. DCC-Format........................................................4
5.5. Consisting..............................................................4
5.6. Accessories with magnetic drives (solenoids)..........5
5.7. Adjusting locomotive parameters...........................5
5.7.1. Programming track..............................................5
5.7.2. Programming On the Main..................................5
6. Unpacking & Installation........................................5
6.1. IR receiver..............................................................5
6.1.1. Additional IR receivers.........................................5
6.2. Power supply.........................................................5
6.2.1. Power supply......................................................5
6.2.2. Setting the input voltage and output voltage......6
6.2.2.1. Practical voltage settings..................................6
6.3. Track connection....................................................6
6.3.1. Wiring two-conductor tracks...............................6
6.3.2. Wiring three-conductor tracks.............................6
6.4. Wiring the programming track...............................6
6.5. ECoSlink................................................................7
6.6. Computer interface................................................7
7. Control elements...................................................7
7.1. Base unit................................................................7
7.2. Handheld controller................................................7
7.2.1. Inserting batteries...............................................8
7.2.2. LCD display.........................................................8
7.2.3. Menu displays.....................................................9
8. Controlling locomotives.........................................9
8.1. Enter a new locomotive in the locomotive list.........9
8.2. Running locomotives..............................................9
8.3. Navigating in the locomotive list.............................9
8.3.1. Scroll with the joystick.........................................9
8.3.2. Manual address entry........................................10
8.4. Editing locomotives..............................................10
8.4.1. Name................................................................10
8.4.2. Symbol..............................................................10
8.4.3. Data format......................................................10
8.4.4. Function mapping.............................................10
8.5. Deleting locomotives............................................10
2
10. Switching accessories........................................11
10.1. Assigning the quick selection button..................11
10.2. Using hotkeys....................................................11
11. Programming....................................................12
11.1. DCC-Programming.............................................12
11.1.1. Direct Mode (CV-Mode)..................................12
11.1.2. Programming on the Main (POM)....................12
11.1.3. Writing locomotive addresses..........................12
11.1.3.1. DCC Main (POM).........................................12
11.1.3.2. DCC - programming track............................12
11.1.4. Reading the locomotive address – DCC...........12
11.1.5. Programming on the programming track - DCC.13
11.1.6. Programming on the Main (POM) - DCC.........13
11.2. Motorola® programming...................................13
11.2.1. Writing the locomotive address – MOT............13
11.2.2. Programming on the programming track - MOT.13
11.3. Programming accessories...................................13
11.3.1. Programming the ESU SwitchPilot...................13
12. Configuration menu..........................................14
12.1. ID of the base unit.............................................14
12.2. Handheld controller ID.......................................14
12.3. System informationen........................................14
12.3.1. Name of the base unit.....................................14
12.3.2. Serial number of the base unit........................14
12.3.3. Software status of the base unit......................14
12.3.4. Name of the handheld controller.....................14
12.3.5. Software version of the handheld controller....14
12.3.6. Current monitor..............................................14
12.4. Joystick delay.....................................................14
12.4.1. for locomotive control.....................................14
12.4.2. in menus.........................................................14
12.5. Joystick speed....................................................14
12.5.1. for acceleration of locomotives........................14
12.5.2. in menus.........................................................14
12.6. Backlight............................................................14
12.6.1. Brightness.......................................................14
12.6.2. Switch-on time................................................14
12.7. Emergency stop configuration............................14
12.8. Automatic track power cut-off...........................14
13. Resetting to factory default values.....................15
13.1. Handheld controller............................................15
13.2. Base unit............................................................15
14. Extending the system........................................15
14.1. Additional handheld controllers..........................15
14.1.1. Data synchronisation.......................................15
14.1.2. Taking over locomotives..................................15
14.2. Coupling the Navigator with the ECoS...............15
14.3. USB Computer interface.....................................15
15.1. Setting the ID of the base unit............................16
16.1. ESU Forum.........................................................16
16.2. Technical hotline................................................16
17. Warranty Certificate..........................................18
18. Annex...............................................................19
18.1. Technical data....................................................19
18.2. Encoding table for accessories............................19