1
Download FCC Information and Copyright
Transcript
P4M900-M7 FE Setup Manual FCC Information and Copyright This equipment has been tes ted and found to comply with the limits of a Class B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed to provide reasonable protec tion against harmful interference in a residential installation. T his equipment generates , uses , and c an radiate radio frequency energy and, if not ins talled and used in accordance with the instructions , may cause harmful interference to radio communications . There is no guarantee that interference will not occur in a particular ins tallation. The vendor makes no representations or warranties with respec t to the contents here and s pecially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make c hanges to the c ontents here without obligation to notify any party beforehand. D uplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing. The content of this user’s manual is subject to be c hanged without notice and we will not be res ponsible for any mis takes found in this user’s manual. All the brand and produc t names are trademarks of their respec tive companies . Table of Contents Chapter 1: Introduction.....................................................3 1.1 Before You Start................................................................... 3 1.2 Package Checklist................................................................ 3 1.3 Motherboard Features.......................................................... 4 1.4 Rear Panel Connectors.......................................................... 5 1.5 Motherboard Layout ............................................................ 6 Chapter 2: Hardware Installation........................................7 2.1 Installing Central Processing Unit (CPU) ................................ 7 2.2 Fan Headers......................................................................... 9 2.3 Installing System Memory.....................................................10 2.4 Connectors and Slots ............................................................12 Chapter 3: Headers & Jumpers Setup................................. 14 3.1 How to Setup Jumpers..........................................................14 3.2 Detail Settings.....................................................................14 Chapter 4: RAID Functions ............................................... 20 4.1 Operation System................................................................20 4.2 Raid Arrays.........................................................................20 4.3 How RAID Works.................................................................20 Chapter 5: Useful Help ..................................................... 22 5.1 Driver Installation Note .......................................................22 5.2 Award BIOS Beep Code........................................................23 5.3 Extra Information................................................................23 5.4 Troubleshooting...................................................................24 A ppendencies: SPEC In Other Language............................. 26 German................................................................................................26 France..................................................................................................28 Italian..................................................................................................30 Spanish ................................................................................................32 Portuguese...........................................................................................34 Polish...................................................................................................36 Russian ................................................................................................38 Arabic..................................................................................................40 Japanese ..............................................................................................42 P4M900-M7 FE CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU ST ART Thank you for choosing our product. Be fore you start installing the mothe rboard, please make sure you follow the instructions be low: Prepare a dry and stable work ing environment with sufficie nt lighting. Always disconne ct the compute r from powe r outle t be fore ope ration. Before you take the mothe rboard out from anti-static bag, ground yourse lf prope rly by touching any safe ly grounde d appliance, or use grounded wrist strap to remove the static charge. Avoid touching the compone nts on mothe rboard or the rear side of the board unless ne cessary. Hold the board on the edge , do not try to be nd or flex the board. 1.2 Do not leave any unfastene d small parts inside the case afte r installation. Loose parts will cause short circuits which may damage the equipment. Keep the compute r from dange rous a rea, such as hea t source , humid air and wate r. PACKAGE CHECKLIST HDD Cable X 1 Installation Guide X 1 Fully Se tup Drive r C D X 1 (full ve rsion manual files inside ) Rear I/O Panel for ATX Case X 1 FDD Cable X 1 (optional) Se rial ATA Cable X 1 (optional) USB 2.0 Cable X1 (optional) Se rial ATA Powe r Cable X 1 (optional) Note: The package contents may differ by area or your motherboard version. 3 Motherboard Manual 1.3 MOT HERBOARD FEAT URES SPEC LGA 775 Intel Core2Duo/ Pe ntium 4 / Pentium Supports Hy per Thre ading/ Execute Disable Bit/ CPU D / Celero n D / C eleron 4xx processor Enha nced Intel SpeedStep®/ Intel Extended up to 3.8 GHz Memory 64 technology *It is recommende d to use processors with 95W power consumption. FSB Chipset Graphic Super I/O 533 / 800 / 1066 MHz VIA P4M900 VIA VT8237A Chrome9 HC 3D / 2D Graphics Max Share d Vide o Memory is 256 MB ITE 8712F Enviro nment Co ntrol initiatives, Provides the most commonly used H/W Monitor legacy Super I/O functionality. Fan Spee d Co ntroller Low Pin C ount Interface ITE's "Smart Guardia n" function DIMM Slots x 2 Main Memory Supports DDR2 533 / 667 Single Channel Mode DDR2 memory mo dule Each DIMM supports Registered DIMM and ECC DIMM is not supported 256/512MB/1GB/2GB DDR2 Max Memory C apicity 4GB IDE Integrated I DE Controller SATA Integrated Seri al ATA Controller LAN PHY Realtek RTL 8201CL PH Y Sound Codec supports PIO Mo de 0~4, Data transfer rates up to 1.5 Gb/s. SATA Version 1.0 specification complia nt. 10 / 100 Mb/s auto negotiation Half / Full duplex capability 5.1 cha nnels a udio o ut ALC662 PCI Expr ess x 16 slot Slots Ultra DMA 33~133 B us Master Mode High- Defi nition Audio s upport x1 Supports PCI- E x 16 expa nsion cards PCI Expr ess x 1 slot x1 Supports PCI- E x 1 ex pansio n cards PCI slot x2 Supports PCI expa nsion cards On Board Floppy connector x1 Each connector supports 2 Flo ppy drives Connector Printer Port C onnector x1 Each connector supports 1 Pri nter port IDE Co nnector x2 Each connector supports 2 IDE device SATA Connector x2 Each connector supports 1 SATA devices 4 P4M900-M7 FE SPEC Front Pa nel Co nnector Back Panel I/O x1 Supports front panel facilities Front Audi o Co nnector x1 Supports front panel a udio function CD-in Co nnector x1 Supports CD audio-in function CPU Fan hea der x1 CPU Fan power s upply (with Smart Fa n function) System Fan hea der x1 System Fan Power supply Clear CMOS header x1 Restore CMOS data to factory defa ult USB connector x2 Each connector supports 2 fr ont panel USB ports Power Connector ( 24pi n) x1 Connects to Power supply Power Connector ( 4pin) x1 Connects to Power supply PS/2 Keyboard x1 Connects to PS/ 2 Key board PS/2 Mo use x1 Connects to PS/ 2 Mo use Serial Port x1 Provide RS- 232 Serial connection VGA Port x1 Connects to mo nitor. LAN port x1 Connects to RJ- 45 ether net cable USB Port x4 Connects to USB devices Audio J ack x3 Provide Audio-In/Out a nd microphone co nnection Board Size 190 mm (W) x 244 mm (L) Special Feature OS Support 1.4 Micro ATX Size Board RAID 0 / 1 support Windows 2000 / XP / VISTA Biostar Reserves the right to a dd or r emove support for any OS with or witho ut notice. REAR PANEL CONNECT ORS LAN PS/2 Mouse Li ne In/ Surround Line Out Mic In 1/ Bass/ Center PS/2 Keyboard COM1 VGA USBX2 USBX2 Since the audio c hip s upports High Definiti on Audio Specific ation, the func tion of eac h audi o jack c an be defined by software. T he input / output function of each audio jac k listed above represents the default s etti ng. However, when c onnecti ng exter nal microphone to the audio port, pleas e us e the Line In (blue) and Mic In (Pink) audio j ac k. 5 Motherboard Manual 1.5 MOT HERBOARD LAYOUT JCFAN1 JKBMS1 COM1 JCOM1 LGA775 CPU1 DIMM1 JVGA1 JPRNT1 JUSB1 DIMM2 JATXPWR1 JUSBV1 IDE1 P4M900 JUSBLAN1 IDE2 JATXPWR2 LAN JAUDIO1 PCI-EX16 Super I/O PCI-EX1_1 BAT1 BIOS JSATA2 JU SB2 VIA VT8237A PCI1 JCDIN1 JSATA1 JUSB3 PCI2 JUSBV2 JCMOS1 Codec JAUDIOF1 FDD1 JSFAN1 JPAN EL 1 Not e: ■ represe nts the 1st pin. 6 P4M900-M7 FE CHAPTER 2: HARDWARE INSTALLATION 2.1 INST ALLING CENT RAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Pin Cap Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle. 7 Motherboard Manual Step 2: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 2-1: Step 2-2: Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the JCFAN1. This completes the installation. 8 P4M900-M7 FE 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. JCFAN1: CPU Fan Heade r 4 1 Pin 1 2 3 4 Assignment Ground +12V FAN RPM rate sense Smart Fan Control JSFAN1: System Fan He ader Pin 1 2 3 3 Assignment Ground +12V FAN RPM rate sense 1 Note: The JSFAN1 supports 3-pin head connector and the JCFAN1 supports 4-pin head connector. When connecti ng with wires onto connectors, pl ease note that the r ed wire is the positi ve and should be connected to pin#2, and the black wire is Ground and should be connected to GND. 9 Motherboard Manual 2.3 INST ALLING SYST EM MEMORY DIMM1 DIMM2 A. Memory Modules 1. 10 Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. P4M900-M7 FE 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. B. Memory Capacity DIMM Socket Location DIMM1 256MB/512MB/1GB/2GB DIMM2 256MB/512MB/1GB/2GB DDR Module Total Memory Size Max is 4GB. 11 Motherboard Manual 2.4 CONNECT ORS AND SLOT S FDD1: Floppy Disk Conne ctor The motherboard prov ides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk ty pes. This connector supports the prov ided f loppy drive ribbon cable. 2 34 1 33 IDE1/IDE2: Hard Disk Conne ctors The motherboard has a 32-bit Enhanced PCI IDE Controller that prov ides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 f unctionality. It has two HDD connectors: IDE1 (primary ) and IDE2 (secondary ). The IDE connectors can connect a master and a slav e driv e, so you can connect up to four hard disk drives. The f irst hard drive should always be connected to IDE1. 40 39 2 1 IDE1 12 IDE2 P4M900-M7 FE PCI-EX16: PCI-Express x16 Slot - PCI-Express 1.0a compliant. - Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, f or an aggregate of 8GB/s totally. PCI-EX1_1: PCI-Express x1 Slot - PCI-Express 1.0a compliant. - Data transf er bandwidth up to 250MB/s per direction; 500MB/s in total. PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. 2X bandwidth ov er the traditional PCI architecture. PCI-EX16 PCI-EX1_1 PCI1/PCI2: Pe riphe ral Component Inte rconne ct Slots This motherboard is equipped with 2 standard PCI slots. PCI stands f or Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI1 PCI2 13 Motherboard Manual CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW T O SET UP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DET AIL SETT INGS JPANEL1: Front Panel Heade r This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch f unctions. PWR_LED On/Off ++ - 9 1 + SPK Pin 1 2 3 4 5 6 7 8 14 Assignment +5V N/A N/A Speaker HDD LED (+) HDD LED (-) Ground Reset control Functio n Speaker Connector Hard drive LED Reset button Pin 9 10 11 12 13 14 15 16 16 8 RST HLED Assignment N/A N/A N/A Power LED (+) Power LED (+) Power LED (-) Power button Ground Functio n N/A N/A Power LED Power-on button P4M900-M7 FE ATX Powe r Source Conne ctor: JATXPWR1 JATXPWR1 allows user to connect 24-pin power connector on the ATX power supply. 12 24 1 13 Pin Assignment Pin Assignment 13 14 15 16 17 18 19 20 21 22 23 24 +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground 1 2 3 4 5 6 7 8 9 10 11 12 +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V JATXPWR2: ATX Powe r Source Conne ctor By connecting this connector, it will provide +12V to CPU power circuit. 1 4 2 3 Pin 1 2 3 4 Assignment +12V +12V Ground Ground 15 Motherboard Manual JUSB2/JUSB3: Heade rs for USB 2.0 Ports at Front Panel This header allows user to connect additional USB cable on the PC f ront panel, and also can be connected with internal USB devices, like USB card reader. 2 10 JUSB2 1 9 JUSB3 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC JSATA1/JSATA2: Se rial ATA Conne ctors The motherboard has a PCI to SATA Controller with 2 channels SATA interf ace, it satisfies the SATA 1.0 spec and with transfer rate of 1.5Gb/s. JSATA2 7 4 1 1 4 7 Pin 1 2 3 4 5 6 7 Assignment Ground T X+ T XGround RXRX+ Ground JSATA1 JAUDIO F1: Front Panel Audio Heade r This header allows user to connect the front audio output cable with the PC f ront panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable. 16 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense P4M900-M7 FE JCDIN1: CD-RO M Audio-in Connector This connector allows user to connect the audio source f rom the v ariaty dev ices, like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc. Assignment Left Channel Input Ground Ground Right Channel Input Pin 1 2 3 4 4 1 JCMO S1: Cle ar CMOS Heade r By placing the jumper on pin2-3, it allows user to restore the BIOS saf e setting and the CMOS data, please carefully f ollow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 1 3 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Proce dures: 1. 2. 3. 4. 5. 6. Remov e AC power line. Set the jumper to “Pin 2-3 close”. Wait f or f ive seconds. Set the jumper to “Pin 1-2 close”. Power on the AC. Reset y our desired password or clear the CMOS data. 17 Motherboard Manual JPRNT1: Printe r Port Connector This header allows you to connector printer on the PC. 25 2 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 18 Assignment -Strobe -ALF Data 0 -Error Data 1 -Init Data 2 -Scltin Data 3 Ground Data 4 Ground Data 5 1 Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 Assignment Ground Data 6 Ground Data 7 Ground -ACK Ground Busy Ground PE Ground SCLT Key P4M900-M7 FE JUSBV1/JUSBV2: Powe r Source Heade rs for USB Ports Pin 1-2 Close: JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1. JUSBV2: +5V for USB ports at f ront panel (JUSB2/JUSB3). Pin 2-3 Close: JUSBV1: USB ports at JUSB1/JUSBLAN1 are powered by +5V standby v oltage. JUSBV2: USB ports at front panel (JUSB2/JUSB3) are powered by +5V standby v oltage. 1 JUSBV1 1 3 Pin 1-2 close 3 JUSBV2 1 3 Pin 2-3 close 1 3 Note: In order to support this function “Power-On system via USB device,” “JUSBV1/ JUSBV2” jumper cap should be placed on Pin 2-3 indi viduall y. 19 Motherboard Manual CHAPTER 4: RAID FUNCTIONS 4.1 O PERAT ION SYST EM z Supports Windows XP Home/Prof essional Edition, and Windows 2000 Prof essional. 4.2 RAID ARRAYS RAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data. 4.3 HOW RAID WORKS RAID 0: The controller “ stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth. Features and Benefits Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the platf orm. Uses: Intended for non-critical data requiring high data throughput, or any env ironment that does not require f ault tolerance. Benefits: prov ides increased data throughput, especially f or large files. No capacity loss penalty f or parity. Drawbacks: Does not deliver any fault tolerance. If any drive in the array f ails, all data is lost. Fault Tolerance: No. Blo ck 1 Block 3 Block 5 20 Block 2 Block 4 Block 6 P4M900-M7 FE RAID 1: Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure. RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media. Features and Benefits Drives: Minimum 2, and maximum is 2. Uses: RAID 1 is ideal f or small databases or any other application that requires f ault tolerance and minimal capacity. Benefits: Prov ides 100% data redundancy. Should one driv e f ail, the controller switches to the other drive. Drawbacks: Requires 2 driv es for the storage space of one driv e. Perf ormance is impaired during driv e rebuilds. Fault Tolerance: Yes. Block 1 Block 2 Block 3 Block 1 Block 2 Block 3 21 Motherboard Manual CHAPTER 5: USEFUL HELP 5.1 DRIVER INST ALLAT ION NOT E After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive. A. Driver Installation To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program. B. Software Installation To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program. C. Manual Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep 2.html 22 P4M900-M7 FE 5.2 AWARD BIOS BEEP CODE Beep Sound One long beep followed by two short beeps High-low siren sound Meaning Video card not found or v ideo card memory bad CPU overheated System will shut down automatically One Short beep when system boot-up No error found during POST Long beeps every other second 5.3 No DRAM detected or install EXT RA INFORMAT ION CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed. After confirmed, please follow steps below to relief the CPU protection function. 1. Remove the power cord from power supply for seconds. 2. Wait for seconds. 3. Plug in the power cord and boot up the system. Or you can: 1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section) 2. Wait for seconds. 3. Power on the system again. 23 Motherboard Manual 5.4 TROUBLESHOOT ING Probable Solution 1. Make sure power cable is No power to the system at all securely plugged in. Power light don’t illuminate, f an inside power supply does not turn 2. Replace cable. on. 3. Contact technical support. 2. Indicator light on key board does not turn on. System inoperativ e. Keyboard lights Using even pressure on both ends of are on, power indicator lights are lit, the DIMM, press down firmly until the and hard driv e is spinning. module snaps into place. 1. System does not boot from hard disk 1. driv e, can be booted f rom optical driv e. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the driv e type in the standard CMOS setup. 2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. 1. Back up data and applications System only boots f rom optical driv e. f iles. Hard disk can be read and applications can be used but booting from hard disk 2. Ref ormat the hard driv e. is impossible. Re-install applications and data using backup disks. Screen message says “Invalid Rev iew system’s equipment. Make sure Conf iguration” or “CMOS Failure.” correct inf ormation is in setup. Cannot boot system after installing 1. Set master/slave jumpers second hard driv e. correctly. 2. Run SETUP program and select correct driv e types. Call the drive manuf acturers f or compatibility with other drives. 24 P4M900-M7 FE This page is intentionally left blank. 25 Motherboard Manual APPENDENCIES: SPEC IN OTHER LANGUAGE GERMAN Spezifikationen LGA 775 Intel Core2Duo/ Pe ntium 4 / Pentium Unterstützt Hyper -Threadi ng / Execute Disable Bit CPU D / C eleron D / Celer on 4xx / Enha nced I ntel Spee dStep® / Intel Prozessoren mit bis zu 3,8 GHz Architecture-64 / Exte nde d Memory 64 *It is recommende d to use processors Technol ogy with 95W power consumption. FSB Chipsatz Grafik Super E/A 533 / 800 / 1066 MHz VIA P4M900 VIA VT8237A Chrome9 HC 3D / 2D Graphics Max. 256MB gemeinsam benutzter Videospeicher ITE 8712F Umgebungskontrolle, Bietet die häufi g verwe ndete n alte n Hardware-Überwachung Super E/A-Funktione n. Lüfterdre hzahl-Co ntroller Low Pin C ount-Schnittstelle "Smart Guar dian" -Funktion v on ITE DDR2 DIMM-Steckplätze x 2 Arbeitsspe icher Unterstützt DDR2 533 / 667 Ein-Kanal DDR2 S peichermodul Jeder DIMM unterstützt registrierte DIMMs. ECC DIMMs werde n nicht 256/512MB/1GB/2GB DDR2. unterstützt. Max. 4GB Ar beitsspeicher Ultra DMA 33 / 66 / 100 / 133Bus Master-Modus IDE Integrierter IDE-Co ntroller SATA Integrierter Serial ATA-Controller LAN PHY Realtek RTL 8201CL PH Y Audio-Cod ec Steckplätz e Unterstützt PIO-Modus 0~4, Datentransferr ate bis zu 1.5Gb/s Konform mit der SATA-Spezifikation Version 1.0. 10 / 100 Mb/s A uto-Negotiation Halb-/ Vollduplex- Funktion Unterstützt High- Definitio n Audio ALC662 5.1-Kanal-Audioausgabe PCI-Steckplatz x2 PCI Expr ess x16 Steckplatz x1 PCI Expr ess x 1-Steckplatz x1 Onboard-A Diskettenlaufwerk anschluss x1 nschluss 26 Jeder Anschluss unterstützt 2 Diskettenlaufwerke Druckeranschluss Anschluss x1 Jeder A nschluss unterstützt 1 Druckera nschluss IDE-Anschluss x2 Jeder A nschluss unterstützt 2 IDE-L aufwerk e P4M900-M7 FE Spezifikationen Rückseiten -E/A Platinengr öße. Sonderfun ktionen OS-Unters tützung SATA-Anschluss x2 Jeder A nschluss unterstützt 1 SATA-Laufwerk Fronttafela nschluss x1 Unterstützt die Fro nttafelfunktio nen Front-Audioa nschluss x1 Unterstützt die Fronttafel-Audioa nschlussfunktion CD-IN-Anschluss x1 CPU-Lüfter-Sockel x1 System-Lüfter-Sockel x1 "CMOS löschen"-Sockel x1 USB-Anschluss x2 Stromanschluss (24- polig) x1 Stromanschluss (4-poli g) x1 PS/2-Tastatur x1 PS/2-Maus x1 Serieller Anschluss x1 VGA-Anschluss x1 LAN-Anschluss x1 USB-Anschluss x4 Audioanschluss x3 Unterstützt die CD Audio-I n-Funktion CPU-Lüfterstromversorgungsanschl uss (mit Smart Fan-Funktion) System-Lüfter-Stromversorgungsa nschluss Jeder A nschluss unterstützt 2 Fronttafel-USB-Anschlüsse 190 mm (B) X 244 mm (L) Unterstützt RAID 0 / 1 Biostar behält sich das Recht v or, ohne Windows 2K / XP / VISTA Ankündigung die Unterstützung für ei n Betriebssystem hinzuzufügen oder zu entferne n. 27 Motherboard Manual FRANCE SPEC LGA 775 Processeurs Intel Core2Duo / P entium 4 / UC Pentium D / Celeron D / Celer on 4xx jusqu'à 3,8 GHz *It is recommende d to use processors with 95W power consumption. Prend en charge les technologies Hyper -Thre ading / d'ex écution de bit de désactivation / I ntel Spe edStep® optimisée/ d'architecture Intel 64 / de mém oire éte ndue 64 Bus frontal 533 / 800 / 1066 MHz Chipset Graphi que s Super E/S Mémoire principale VIA P4M900 VIA VT8237A Chrome9 HC 3D / 2D Graphics Mémoire vidé o partagée maximale de 256 Mo ITE 8712F Initiatives de co ntrôle e nvironnementales, Fournit la fo nctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée. Contrôleur de vitesse de ventilateur Interface à faible compte de broc hes Fonction " Gardie n i ntelligent" de l'ITE Fentes DDR 2 DIMM x 2 Module de mém oire DDR2 à mo de à simple Prend en charge la DDR 2 533 / 667 voie Chaque DIMM prend e n charge des Les DIMM à r egistres et DIMM avec code DDR2 de 256 M o / 512 Mo / 1Go / 2 Go correcteurs d'erreurs ne so nt pas prises en Capacité mémoire maximale de 4 Go charge Contrôleur IDE intégr é / 133 Mode principale de Bus Ultra DMA 33 / 66 / 100 IDE Prend en charge le mode PIO 0~4, SATA Contrôleur Serial ATA intégré : LAN PHY Realtek RTL 8201CL PH Y Codec audio Fentes Connecteu r embarqué 28 Taux de transfert jusqu'à 1.5 Go/s. Conforme à la spécification SATA Version 1.0 10 / 100 Mb/s négociation a utomatique Half / Full duplex capability Prise en c harge de l'audio haute dé finition ALC662 Sortie audio à 5.1 voies Fente PCI x2 Slot PCI Ex press x16 x1 Slot PCI Ex press x 1 x1 Connecteur de disquette x1 Connecteur de P ort d'imprimante x1 Chaque connector pre nd en charge 2 lecteurs de disquettes Chaque connector pre nd en charge 1 Port d'imprimante P4M900-M7 FE SPEC Connecteur IDE x2 Connecteur SATA x2 Connecteur du pa nne au avant x1 Connecteur Audio du panneau ava nt x1 Connecteur d'entré e CD x1 Embase de ve ntilateur UC x1 Embase de ve ntilateur système x1 Embase d'e ffacement CMOS x1 Connecteur USB x2 Connecteur d'alimentatio n x1 Chaque connecteur prend e n char ge 2 périphéri ques I DE Chaque connecteur prend e n char ge 1 périphéri que SATA Prend en charge les é quipements du panneau avant Prend en charge la fo nction a udio du panneau avant Prend en charge la fo nction d'entrée audio de CD Alimentation électrique du ve ntilateur UC (avec fo nction de v entilateur intellige nt) Alimentation électrique du ve ntilateur système Chaque connecteur prend e n char ge 2 ports USB de panneau ava nt (24 broches) Connecteur d'alimentatio n x1 (4 br oches) Clavier PS/2 x1 Souris PS/2 x1 E/S du Port série x1 panneau Port VGA x1 arrière Port LAN x1 Port USB x4 Fiche audio x3 Dimension s de la 190 mm (l) X 244 mm (H) carte Fonctionna lités Prise en c harge RAID 0 / 1 spéciales Support SE Biostar se réserve le droit d'ajo uter o u de Windows 2K / XP / VISTA supprimer le support de SE avec o u sa ns préavis. 29 Motherboard Manual IT ALIAN SPECIFICA LGA 775 Processore Intel Core 2Duo/ Pentium 4 / Supporto di Hyper -Threadi ng / Ex ecute Disable CPU Pentium D / Celer on D / Celeron 4xx fino Bit / Enhance d I ntel Spee dStep® / a 3.8 GHz Architettura Intel 64 / Tecnologi a Extende d *It is recommende d to use processors Memory 64 with 95W power consumption. FSB Chipset Grafica 533 / 800 / 1066 MHz VIA P4M900 VIA VT8237A La memoria vi deo co ndivisa massima è di Chrome9 HC 3D / 2D Graphics 256MB Funzioni di co ntrollo dell’ambiente: ITE 8712F Super I/O Fornisce le funzionalità le gacy Super I/O Monitoraggio hardware usate più comunemente. Controller velocità ventolina Interfaccia LPC (L ow Pin Count) Funzione "Smart Guardi an" di I TE Alloggi DIMM DDR 2 x 2 Memoria principale Modulo di memoria DDR2 a canale singolo Supporto di DDR2 533 / 667 Ciascun DIMM supporta DDR 2 256MB / DIMM registrati e DIMM ECC no n sono supportati 512MB / 1GB / 2GB Capacità massima della memori a 4GB Modalità B us Master Ultra DMA 33 / 66 / 100 / IDE Controller IDE i ntegrato 133 Supporto modalità PIO Mode 0- 4 Velocità di trasferimento dei dati fi no a 1.5 SATA Controller Serial ATA inte grato Gb/s. Compatibile specifiche SATA Versione 1.0. LAN PHY Codec audio 30 Uscita audio 5.1 canali x2 Alloggio PCI Ex press x16 x1 Alloggio PCI Ex press x1 x1 Connettori Connettore flo ppy su scheda Capacità Half / Full Duplex Supporto audio High-Definition (HD) ALC662 Alloggio PCI Alloggi Negoziazione automatica 10 / 100 Mb/s Realtek RTL 8201CL PH Y x1 Connettore Porta stampa nte x1 Connettore IDE x2 Ciascun connettore supporta 2 unità Floppy Ciascun connettore supporta 1 P orta stampante Ciascun connettore supporta 2 unità IDE P4M900-M7 FE SPECIFICA Connettore SATA x2 Connettore pa nnello fro ntale x1 Ciascun connettore supporta 1 unità SATA Supporta i servizi del pa nnell o fr ontale Connettore audio frontale x1 Supporta la funzione audi o pannello frontale Connettore CD-in x1 Supporta la funzione i nput audio C D Collettore ventolina CPU x1 Collettore ventolina sistema x1 Collettore cancellazione CMOS x1 Connettore USB x2 Connettore alimentazione x1 Alimentazione ve ntolina CPU (co n funzione Smart Fan) Alimentazione ve ntolina di sistema Ciascun connettore supporta 2 porte USB pannello frontale (24 pin) Connettore alimentazione x1 (4 pi n) Tastiera PS/2 x1 Mouse PS/2 x1 I/O Porta seriale x1 pannello Porta VGA x1 posteriore Porta LAN x1 Dimension i scheda Porta USB x4 Connettore audio x3 190 mm (lar ghezza) x 244 mm (altezza) Caratterist iche Supporto RAID 0 / 1 speciali Sistemi operativi supportati Biostar si riserva il diritto di aggiungere o Windows 2K / XP / VISTA rimuovere il supporto di qualsiasi sistema operativo se nza pre avviso. 31 Motherboard Manual SPANISH Especificación LGA 775 Procesador I ntel Core 2Duo / Penti um Admite Hyper -Threadi ng / Bit de deshabilitación CPU 4 / Pentium D / Celero n D / Celero n de ejecució n / Intel SpeedStep® Me jorado / Intel 4xx hasta 3,8 GHz Architecture-64 / Tecnologí a Extended Memor y *It is recommende d to use processors 64 with 95W power consumption. FSB 533 / 800 / 1066 MHz Conjunto VIA P4M900 de chips VIA VT8237A Gráficos Chrome9 HC 3D / 2D Graphics Memoria máxima de vídeo compartida de 256MB ITE 8712F Iniciativas de control de entor no, Le ofrece las funcionalidades Súper E/S hereda das de uso más común Súper E/S. Monitor hardware Controlador de velocida d de ve ntilador Función "Guardia intelige nte" de I TE Interfaz de cue nta Low Pin Ranuras DIMM DDR 2 x 2 Admite DDR2 de 533 / 667 Memoria Cada DIMM admite DDR de 256MB principal /512MB /1GB / 2GB Capacidad máxima de memoria de Módulo de memoria DDR2 de canal Sencillo No admite DIMM re gistrados o DIMM compatibl es con ECC 4GB IDE Controlador IDE inte grado SATA Controlador ATA Serie Integra do Red Local Realtek RTL 8201CL PH Y Códecs de sonido Ranuras Conectore s en placa 32 Modo bus maestro Ultra DMA 33 / 66 / 100 / 133 Soporte los Mo dos PIO 0~4, Tasas de transfere ncia de hasta 1.5 Gb/s. Compatible con la versión SATA 1.0. Negociación de 10 / 100 Mb/s Funciones Half / F ull dúplex Soporte de soni do de Alta Defi nición ALC662 Salida de sonido de 5.1 canales Ranura PCI X2 Ranura PCI Ex press x16 X1 Ranura PCI ex press x 1 X1 Conector disco flexible X1 Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora Conector IDE X2 Cada conector soporta 2 dispositivos IDE Conector SATA X2 Cada conector soporta 1 dispositivos SATA Cada conector soporta 2 uni dades de disco flexible P4M900-M7 FE Especificación Conector de pa nel fro ntal X1 Soporta instalaciones en el panel fr ontal Conector de sonido frontal X1 Soporta funcio nes de sonido e n el pa nel frontal Conector de entra da de C D X1 Soporta funció n de e ntrada de sonido de CD Cabecera de ve ntilador de C PU X1 Fuente de alime ntación de ve ntilador de CPU (con funció n Smart Fan) Cabecera de ve ntilador de sistema X1 Cabecera de borrado de CMOS X1 Conector USB X2 Conector de alimentación X1 Fuente de alimentación de ventilador de sistema Cada conector soporta 2 puertos USB fro ntales (24 patillas) Conector de alimentación X1 (4 patillas) Teclado PS/2 Panel Ratón PS/2 X1 Puerto serie X1 trasero de Puerto VGA E/S Tamaño de la placa Funciones especiales Puerto de re d local operativo X1 X1 Puerto USB X4 Conector de sonido X3 190mm. (A) X 244 Mm. (H) Admite RAID 0 / 1 Soporte de sistema X1 Windows 2K / XP / VISTA Biostar se reserva el derecho de aña dir o r etirar el soporte de cualquier SO con o sin aviso previo. 33 Motherboard Manual PORT UGUESE ESPECIFICAÇÕES LGA 775 Processador Intel Core2Duo / Pe ntium 4 Suporta as tecnologias Hyper -Threa ding / CPU / Pentium D / Celer on D / Celero n 4xx Execute Disable Bit / Enha nced I ntel até 3,8 GHz SpeedStep® / Intel Arquitecture -64 / *It is recommende d to use processors Extende d Memor y 64 with 95W power consumption. FSB Chipset Placa gráfica 533 / 800 / 1066 MHz VIA P4M900 VIA VT8237A Chrome9 HC 3D / 2D Graphics Memória de víde o máxima partilha da: 256 MB ITE 8712F Especificaç Proporciona as funcionalida des mais ão Super utilizadas em termos da especificação I/O Super I/O. Iniciativas para control o do am biente Monitorização do hardware Controlador da velocida de da v entoinha Função "Smart Guardia n" da I TE Interface LPC (Low Pi n Co unt). Ranhuras DIMM DDR2 x 2 Suporta mó dulos DDR2 533 / 667 Memória Cada mó dulo DIMM suporta uma principal memória DDR 2 de 256MB /512 MB / 1 GB / 2GB Módulo de memória DDR2 de canal simples Os módulos DIMM r egistados e os DIMM ECC não são suportados Capacidade máxima de memória : 4 GB IDE Modo Bus master Ultra DMA 33 / 66 / 100 / 133 Controlador IDE inte grado Suporta o modo PIO 0~4, Velocidades de transmissão de dados até 1.5 SATA Gb/s. Controlador Serial ATA integra do Compatibilidade com a especificação SATA versão 1.0. LAN PHY Codec de som Ranhuras Auto ne gociação de 10 / 100 MB/s Realtek RTL 8201CL PH Y Capacidade semi/full- duplex Suporta a especificação High-De finition Audi o ALC662 Saída de á udio de 5.1 ca nais Ranhura PCI x2 Ranhura PCI Express x 16 x1 Ranhura PCI Express x 1 x1 Conectore Conector da unida de de disquetes x 1 Cada co nector suporta 2 unida des de disquetes s na placa Conector da para impressora Cada conector suporta 1 Porta para impr essora 34 x1 P4M900-M7 FE ESPECIFICAÇÕES Conector IDE x2 Cada conector suporta 2 dispositivos IDE Conector SATA x2 Cada conector suporta 1 dispositivo SATA Conector do pai nel fro ntal x1 Conector de áudio fro ntal x1 Suporta a função de áudio no painel fr ontal Conector para e ntrada de C Ds x1 Suporta a e ntrada de áudi o a partir de C Ds Conector da ve ntoinha da CPU x1 Conector da ve ntoinha do sistema x1 Para suporte de várias funções no painel frontal Alimentação da ventoi nha da CPU (com a função Smart Fan) Alimentação da ventoi nha do sistema Conector para limpeza do CMOS x1 Conector USB x2 Conector de alimentação x1 Cada conector suporta 2 portas USB no pai nel frontal (24 pinos) Conector de alimentação x1 (4 pi nos) Teclado PS/2 Entradas/ Saídas no painel traseiro Tamanho da pl aca x1 Rato PS/2 x1 Porta série x1 Porta VGA x1 Porta LAN x1 Porta USB x4 Tomada de áudio x3 190 mm (L) X 244 mm (A) Característ icas Suporta as funções RAID 0 / 1 especiais Sistemas operativos suportado s A Biostar reserva-se o direito de adicionar ou Windows 2K / XP / VISTA remover suporte par a qualquer sistema operativo com ou sem aviso prévio. 35 Motherboard Manual POLISH SPEC LGA 775 Procesor Intel Cor e2Duo/ Penti um 4 / Procesor Obsługa Hyper -Threa ding / Execute Disa ble Bit Pentium D / Celeron D / Celer on 4xx do / Enha nced I ntel Spee dStep® / Intel 3,8 GHz Architecture-64 / Exte nde d Memory 64 *It is recommende d to use processors Technol ogy with 95W power consumption. FSB Chipset Grafika 533 / 800 / 1066 MHz VIA P4M900 VIA VT8237A Maks. wielkość współdzielonej pamięci video Chrome9 HC 3D / 2D Graphics wynosi 256MB Gniazda DDR 2 DIMM x 2 Pamięć główna Moduł pamięci DDR2 z trybem poje dynczego Obsługa DDR2 533 / 667 Każde gniazdo DIMM obsługuje mo duły kanału 256MB /512MB / 1GB / 2GB DDR2 Brak obsługi Registered DIMM or az ECC DIMM Maks. wielkość pamięci 4GB Super I/O ITE 8712F Funkcje kontroli warunków prac y, Zapewnia najbardziej powszechne Monitor H/W funkc je Super I/O. Kontroler prę dkości wentylatora Interfejs L ow Pin Count Funkcja ITE "Smart Guar dian" Ultra DMA 33 / 66 / 100 / 133 Tryb B us Master IDE Zintegrowany kontroler IDE SATA Zintegrowany kontroler Serial ATA obsługa PIO tryb 0~4, Transfer da nych do 1.5 Gb/s. Zgodność ze specyfikacją SATA w wersji 1.0. 10 / 100 Mb/s z automatyczną negocjacją LAN PHY szybkości Realtek RTL 8201CL PH Y Działanie w trybie połowicznego / pełnego dupleksu Kodek dźwiękowy Gniazda Złącza Obsługa Hi gh- Definitio n Audio ALC662 5.1 ka nałowe wy jście audio Gniazdo PCI x2 Gniazdo PCI Express x 16 x1 Gniazdo PCI Express x 1 x1 Złącze napędu dyskietek x1 Każde złącze obsługuje 2 na pędy dyskietek wbudowan Złącze Port druk arki x1 Każde złącze obsługuje 1 Port drukarki e Złącze IDE x2 Każde złącze obsługuje 2 urządze nia I DE Złącze SATA x2 Każde złącze obsługuje 1 urządze nie SATA 36 P4M900-M7 FE SPEC Złącze panela przedniego x1 Obsługa eleme ntów pa nela przedniego Przednie złącze a udio x1 Obsługa funkcji audio na pa nelu przednim Złącze wejścia CD x1 Obsługa funkcji wejścia a udio CD Złącze główkowe wentylatora procesora Zasilanie wentylatora procesora (z funkcją x1 Złącze główkowe wentylatora systemowego x1 Smart Fan) Zasilanie wentylatora systemowego Złącze główkowe kasowani a Back Panel I/O Wymiary płyty Funkcje specjalne CMOS x1 Złącze USB x2 Złącze zasilania (24 pi nowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatura PS/2 x1 Mysz PS/2 x1 Port szeregowy x1 Port VGA x1 Port LAN x1 Port USB x4 Gniazdo audio x3 operacyjn ego przednim 190 mm (S) X 244 mm (W) Obsługa RAID 0 / 1 Obsluga systemu Każde złącze obsługuje 2 porty USB na pa nelu Biostar zastrzega sobie prawo do dawania lub Windows 2K / XP / VISTA odwoływania obsługi dowolnego systemu operacyjnego bez powiadomie nia. 37 Motherboard Manual RUSSIAN СПЕЦ LGA 775 CPU Процессор Intel Core 2Duo/ Pe ntium (центра льны 4 / Pentium D / Celero n D / Celero n Подде ржка техноло гий Hy per-Thre ading / Execute Disable Bit / Enha nced I ntel й 4xx до 3.8 ГГц процессор) *It is recommende d to use processors Extende d Memor y 64 Technology SpeedStep® / Intel Architecture-64 / with 95W power consumption. FSB 533 / 800 / 1066 МГц Набор VIA P4M900 микросхем VIA VT8237A Графика Chrome9 HC 3D / 2D Graphics Максимальная совмес тно используемая видео память составляет 256 МБ Слоты DDR2 DIMM x 2 Подде ржка DDR2 533 / 667 Модуль памя ти с однока наль ным режим ом Основная Каждый модуль DIMM DDR2 память поддержива ет 256MB / 512МБ / 1ГБ Не подде рживае т за рег истриров анные модули DIMM and ECC DIMM / 2ГБ DDR2 Максимальная ёмк ость памя ти 4 ГБ ITE 8712F Super I/O Обеспечива ет на ибо лее Инициа тивы по охране ок ружающей среды, используемые дейс твующие Аппара тный монитор функциональные возможности Регуля тор скорости Super I/O. Функция ITE "Smart Guardian" Инте рфейс с низким к оличеством (Интелле ктуа льна я защ ита) выводов Встроенное устройств о у прав ления Режим "хозя ина " ш ины Ultra DMA 33 / 66 / IDE встрое нными интерфе йсами 100 / 133 устройс тв Подде ржка режима PIO 0~4, скорость передач и данных до 1.5 SATA гига бит/с. Встроенное последов ате льное Соотве тств ие спецификации SATA версия устройс тво управле ния ATA 1.0. Локаль ная сеть Звуково й кодек Слоты Встроенный разъём Частич ная / по лная дупле ксная способ ность Звукова я поддержка High-De finition ALC662 5.1кана льный звуков ой выход Слот PCI Слот PCI Ex press x16 x2 x1 Слот PCI Ex press x 1 x1 Разъём НГМД x1 Разъём Порт подключе ния принте ра Разъём IDE 38 Автоматическое сог ласова ние 10 / 100 М б/с Realtek RTL 8201CL PH Y Каждый разъём по дде рживае т 2 нако пителя на г ибк их м агнитных дисках Каждый разъём по дде рживае т 1 П орт x1 x2 подк лючения принтера Каждый разъём поддерживает 2 встро енных интерфейса накопителе й P4M900-M7 FE СПЕЦ Разъём SATA x2 Разъём на лицево й пане ли x1 Входно й звук овой раз ъём x1 Разъём вв ода для CD x1 Каждый разъём по дде рживае т 1 устро йство SATA Подде ржка устро йств на лицево й па нели Подде ржка звук овых функций на лицево й пане ли Подде ржка фу нкции вво да для CD Контак тирующее Источник пита ния для ве нтиля тора прис пособление ве нтиля тора центра льно го процессора (с фу нкцией центра льно го процессора x1 Контак тирующее приспосо бле ние вентиля тора системы x1 интелле ктуа льно го вентилято ра) Источник пита ния для ве нтиля тора сис темы Открытое контак тирующее Задняя пане ль средств ввода-выво д а прис пособление CMOS x1 USB-разъём x2 Разъем питания ( 24 вывод) x1 Разъем питания ( 4 вывод) x1 Клавиа тура PS/ 2 x1 Мышь PS/2 x1 Последо вате льный по рт x1 Порт VGA x1 Порт LAN x1 USB-порт x4 пане ли на лицево й пане ли Гнездо для по дключ ения наушников Размер Каждый разъём по дде рживае т 2 USB-порта x3 190 мм (Ш ) X 244 мм (В) Специаль ны е технические Подде ржка RAID 0 / 1 харак терист ики Подде ржка OS Biostar сохраня ет за собо й прав о добав лять Windows 2K / XP / VISTA или уда лять сре дства обес пече ния для OS с или без пре дварительного уведомле ния. 39 Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت LGA 775 Intel Core2Duo/ Pe ntium 4 / Pentiumﻡﻌﺎﻟﺠﺎت وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﺑ ﺘﺮدد ﻳﺼﻞ إﻟﻰ D / C eleron D / Celer on 4xx 8.3 اﻟﻤﺮآﺰﻳ ﺔ ﺝﻴﺠﺎ هﺮﺕﺰ *It is recommended to use processors with Hyper -Thre ading / Exec ute Disabl eﺕﺪﻋﻢ ﺕﻘﻨﻴﺎت Bit / Enhance d I ntel Spee dStep® / Extende d Memor y 64 Technology 95W power co nsumption. اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ ﻡﻴﺠﺎ هﺮﺕﺰ 533 / 800 / 1066ﺕﺮدد اﻟﺠﺎﻥﺒﻲ VIA P4M900 ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت VIA VT8237A Chrome9 HC 3D / 2D Graphics ﻓﺘﺤﺔDDR2 DIMM ﻡﻴﺠﺎ ﺑﺎﻳﺖ256أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪﻳﻮ اﻟﻤﺸﺘﺮآﺔ ﻋﺪد2 ﻡﻴﺠﺎ ﺑﺎﻳﺖ 533 / 667ﺳﻌﺎت DDR2ﺕﺪﻋﻢ اﻟﺬاآﺮ ة ﻡﻦ ﻥﻮع اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ ﺳﻌﺔ DDR2ﺕﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع DIMMﺕﺪﻋﻢ آﻞ ﻓ ﺘﺤﺔ أﺣﺎدﻳﺔ اﻟﻘﻨﺎة DDR2وﺣﺪة ذا آﺮة ﻡﻴﺠﺎ ﺑﺎﻳﺖ و 1ﺝﻴﺠﺎ ﺑﺎﻳﺖ 2 /ﺝﻴﺠﺎ /512ﻡﻴﺠﺎ ﺑﺎﻳﺖ256 ECCوﺕﻠﻚ اﻟﺘﻲ ﻻ ﺕﺘﻮاﻓﻖ ﻡﻊ DIMMﻻ ﺕﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة ﺑﺎﻳﺖ ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 4ﺝﻴﺠﺎ ﺑﺎﻳﺖ ITE 8712F Super I/O اﻷآﺜﺮ ا ﺳﺘﺨﺪاﻡ ًﺎ Super I /O .ﺕﻮﻓﺮ وﻇﻴﻔﺔ Interface Low Pi n Countﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ: ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة ﻡﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣ ﺔ ITEﻡﻦ ""Smart Guar dianوﻇﻴﻔﺔ Ultra DMA 33 / 66 / 100 / 133ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ ﻡﻨﻔﺬ IDE ﻡﺘﻜﺎﻡﻞ IDEﻡﺘﺤﻜﻢ SATA ﻡﺘﻜﺎﻡﻞ Serial ATAﻡﺘﺤ ﻜﻢ وﺿﻊ رﺋﻴﺴﻲ PIO Mode 0~4دﻋﻢ وﺿﻊ ﺵﺒﻜﺔ داﺥﻠﻴﺔ Realtek RTL 8201CL PH Y آﻮدﻳﻚ اﻟﺼﻮ ت ALC662 ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺕﺼﻞ إﻟﻰ 1.5ﺝﻴﺠﺎﺑﺖ /ﺙﺎﻥﻴﺔ. 1.0.اﻹﺹﺪار SATAﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت ﺕﻔﺎوض ﺕﻠﻘﺎﺋﻲ 100 /10ﻡﻴﺠﺎ ﺑﺎﻳﺖ /ﺙﺎﻥﻴﺔ إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ/اﻟﻨﺼﻔﻲ ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘ ﻌﺮﻳﻒ ﻡﻦ 5.1ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮ ت 40 P4M900-M7 FE اﻟﻤﻮاﺻﻔﺎت اﻟﻔﺘﺤﺎت اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ اﻟﻠﻮﺣ ﺔ ﻡﻨﺎﻓﺬ دﺥﻞ /ﺥﺮج اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﻓﺘﺤﺔ PCI ﻋﺪد 2 ﻓﺘﺤﺔ PCI Expressx16 ﻋﺪد 1 ﻓﺘﺤﺔPCI Express x 1 ﻋﺪد 1 ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ ﻋﺪد 1 ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ ﻋﺪد 1 ﻡﻨﻔﺬIDE ﻋﺪد 2 IDEﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬSATA ﻋﺪد 2 SATAﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻋﺪد 1 ﻳﺪﻋﻢ ﺕﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬCD-IN ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡﺞ وﺹﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ ﻋﺪد 1 Smart Fanﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ وﺹﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 1 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم وﺹﻠﺔ ﻡﺴﺢCMOS ﻋﺪد 1 ﻡﻨﻔﺬUSB ﻋﺪد 2 ﻡﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس( ﻋﺪد 1 ﻡﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ) 4دﺑﺎﺑﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻡﻔﺎﺕﻴﺢPS/2 ﻋﺪد 1 ﻡﺎوس PS/2 ﻋﺪد 1 ﻡﻨﻔﺬ ﺕﺴﻠﺴﻠﻲ ﻋﺪد 1 ﻡﻨﻔﺬ VGA ﻋﺪد 1 ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺕﺼﺎل ﻡﺤﻠﻴﺔ ﻋﺪد 1 ﻡﻨﺎﻓﺬ USB ﻋﺪد 4 ﻡﻘﺒﺲ ﺹﻮت ﻋﺪد3 ﺣﺠﻢ اﻟﻠﻮﺣﺔ 190ﻡﻢ )ﻋﺮض ( 244 Xﻡﻢ ) ارﺕﻔﺎع( ﻣﺰاﻳﺎ ﺧﺎﺻﺔ RAID 0 / 1ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ 41 Windows 2K / XP / VISTA ﻳﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔUSBﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم Biostarﺕﺤﺘﻔﻆ ﺕﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو ﺑﺪون إﺥﻄﺎر . Motherboard Manual JAPANESE 仕様 LGA 775 Intel Core2Duo/ Pe ntium 4 / Pentium Hyper -Thre ading / Exec ute Disabl e Bit / CPU D / Celero n D / C eleron 4xx processor Enha nced Intel SpeedStep® / I ntel up to 3.8 GHz Architecture-64 / Exte nde d Memory 64 *It is recommende d to use processors Technol ogy をサポートします with 95W power consumption. FSB 533 / 800 / 1066 MHz チップセッ VIA P4M900 ト グラフィッ クス VIA VT8237A Chrome9 HC 3D / 2D Graphics 最大の共有ビデオメモリは256MBです DDR2 DIMMスロット x 2 メインメモ リ DDR2 533 / 667をサポート シングル チャンネルモードDDR 2メモリモジュール 各DIMMは 256/ 512MB/1GB/ 2GB 登録済みDIMMとECC DIMMはサポートされません DDR2をサポート 最大メモリ容量4GB Super I/O ITE 8712F 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシー H/Wモニター Super I/O機能を採用しています。 ファン速度コントローラ/ モニター 低ピンカウントインターフェイス ITEの「スマートガーディアン」機能 IDE 統合IDEコントローラ SATA 統合シリアルATAコントローラ LAN PHY Realtek RTL 8201CL PH Y サウンド Codec スロット PIO Mode 0~4のサポート、 最高1.5 Gb/秒のデータ転送速度 SATAバージョン1.0仕様に準拠。 10 / 100 Mb/秒のオートネゴシエーション 半/全二重機能 ハイデフィニションオーディオのサポート ALC662 5.1 チャンネルオーディオアウト PCIスロット x2 PCI Expr ess x16スロット x1 PCI Expr ess x 1スロット x1 フロッピーコネクタ x1 プリンタポートコネクタ x1 オンボード コネクタ 42 Ultra DMA 33 / 66 / 100 / 133バスマスタモード 各コネクタは2つのフロッピードライブをサポートし ます 各コネクタは1つのプリンタポートをサポートします P4M900-M7 FE 仕様 背面パネル I/O ボードサイ ズ 特殊機能 OSサポー ト IDEコネクタ x2 各コネクタは2つのIDEデバイスをサポートします SATAコネクタ x2 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします CDインコネクタ x1 CDオーディオイン機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 USBコネクタ x2 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 シリアルポート x1 VGAポート x1 LANポート x1 USBポート x4 オーディオジャック x3 各コネクタは2つのフロントパネルUSBポートをサポ ートします 190 mm (幅) X 244 mm (高さ) RAID 0 / 1のサポート Windows 2K / XP / VISTA Biostarは事前のサポートなしにOSサポートを追加ま たは削除する権利を留保します。 2007/11/09 43
