Download ACEX-4600-EDK User`s Manual

ACEX-4600-EDK
EDK Standard I/O Connector Break-Out Board
USER’S MANUAL
ACROMAG INCORPORATED
30765 South Wixom Road
Wixom, MI 48393-7037 U.S.A.
Tel: (248) 295-0310
Fax: (248) 624-9234
Copyright 2013, Acromag, Inc., Printed in the USA.
Data and specifications are subject to change without notice.
8501-018B
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
The information contained in this manual is subject to change without notice. Acromag, Inc. makes no
warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Further, Acromag, Inc. assumes no responsibility
for any errors that may appear in this manual and makes no commitment to update, or keep current,
the information contained in this manual.
No part of this manual may be copied or reproduced in any form, without the prior written consent of
Acromag, Inc.
IMPORTANT SAFETY CONSIDERATIONS
It is very important for the user to consider the possible adverse effects of power, wiring, component,
sensor, or software failures in designing any type of control or monitoring system. This is especially
important where economic property loss or human life is involved. It is important that the user
employ satisfactory overall system design. It is agreed between the Buyer and Acromag, that this is
the Buyer's responsibility.
Acromag, Inc. Tel: 248-295-0310
-2-
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
1.0 General Information....................................................................... 5
Key Features..................................................................................................................................... 5
Introduction ..................................................................................................................................... 6
2.0 Ordering Information ..................................................................... 6
3.0 Preparation For Use ....................................................................... 7
Unpacking and Inspection................................................................................................................ 7
4.0 Operational Block Diagram ............................................................ 8
5.0 Board Layout .................................................................................. 9
6.0 Connectors ................................................................................... 12
200 – Pin SEARAY Connector – J1 .................................................................................................. 12
500 – Pin SEARAY Connector – J2 .................................................................................................. 17
DisplayPort 1 Connector – P10 ...................................................................................................... 30
DisplayPort 2 Connector – P12 ...................................................................................................... 30
DisplayPort 3 Connector – P18 ...................................................................................................... 31
HDMI 1 Connector – P9 ................................................................................................................. 31
HDMI 2 Connector – P11 ............................................................................................................... 32
HDMI 3 Connector – P17 ............................................................................................................... 32
COM 1 RS-232/485 Connector – P19A (Bottom) ........................................................................... 33
COM 2 RS-232/485 Connector – P19B (Top) ................................................................................. 33
VGA Connector – J14 ..................................................................................................................... 33
XMC Rear I/O Site 1 Connector – P6 .............................................................................................. 34
XMC Rear I/O Site 1 Connector – P8 .............................................................................................. 35
XMC Rear I/O Site 2 Connector – P5 .............................................................................................. 36
XMC Rear I/O Site 1 Connector – P7 .............................................................................................. 37
PMC Rear I/O Site 1 Connector – J7............................................................................................... 38
PMC Rear I/O Site 2 Connector – J6............................................................................................... 39
PCIe x16 @ x4 Connector – J4........................................................................................................ 40
Dual USB 2.0 Port 1 & 2 Connector – J9 ........................................................................................ 41
Dual USB 3.0 Port 1 & 2 Connector – J11 (See note, page 53) ...................................................... 41
Dual USB 3.0 Port 3 & 4 Connector – J10 (See note, page 53) ...................................................... 42
SATA 0 Connector – J5 ................................................................................................................... 42
SATA 1 Connector – J8 ................................................................................................................... 43
LAN 1 Connector – J12 ................................................................................................................... 43
Acromag, Inc. Tel: 248-295-0310
-3-
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
LAN 2 Connector – J13 ................................................................................................................... 44
Dual Audio (Line In/ Line Out) Connector – J15............................................................................. 44
GPIO Header – P15......................................................................................................................... 44
LPC Bus Header – P16 .................................................................................................................... 45
Miscellaneous I/O Header 1 – P14................................................................................................. 45
Miscellaneous I/O Header 2 – P13................................................................................................. 45
Fan Power – P2 .............................................................................................................................. 46
Fan Power – P3 .............................................................................................................................. 46
7.0 Jumpers / Switch Settings ............................................................ 47
8.0 Handling ....................................................................................... 48
ESD Safe Work Area Guidelines ..................................................................................................... 48
9.0 Service and Repair........................................................................ 49
Service and Repair Assistance........................................................................................................ 49
Preliminary Service Procedure ....................................................................................................... 49
Where to Get Help ......................................................................................................................... 49
10.0 Specifications ............................................................................... 50
Physical .......................................................................................................................................... 50
Power Requirements ..................................................................................................................... 50
Environmental................................................................................................................................ 50
Revision History .................................................................................... 51
Appendix ............................................................................................... 52
Drive Compatibility ........................................................................................................................ 52
USB 3.0 Data Rate .......................................................................................................................... 53
Certificate of Volatility .......................................................................... 54
Acromag, Inc. Tel: 248-295-0310
-4-
www.acromag.com
ACEX-4600-EDK User’s Manual
1.0
COM Express System Development Kit
General Information
The ACEX-4600-EDK is an engineering development kit to be used
with the ACEX-4620/ACEX-4610 Type 6 COM Express Carrier boards.
It provides access to all Type 6 COM Express peripherals via industrystandard connectors.
Key Features

Acromag, Inc. Tel: 248-295-0310
Provides access to peripherals of Type 6 COM Express CPU
through standard connectors.
o
3 HDMI ports
o
3 DisplayPort connectors (multiplexed with HDMI)
o
1 VGA connector
o
Audio (One Line in and One Line out)
o
2 RS-232/485 Serial Communication ports
o
1 Gigabit Ethernet LAN port from CPU
o
1 Gigabit Ethernet LAN port from carrier
o
PCIe x4 connection through x16 connector
o
4 USB 3.0 ports (See note, page 53)
o
2 USB 2.0 ports

Supports the use of two 2.5” SATA drives.

Provides connections to Rear I/O signals from PMC/XMC
expansion cards located on the ACEX-46xx carrier using standard
high-speed connectors.

Allows the system to be powered by a lab bench power supply or
an external power adapter.
-5-
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
Introduction
The ACEX-4600-EDK is intended to be used as a development
platform for designing a COM Express system tailored to the user’s
specific needs. By providing industry-standard connectors for the
COM Express I/O signals, the ACEX-4600-EDK allows the user to
design and test a system around a COM Express CPU module without
the need for a specialized carrier. It also provides standard
connections to interface with the PMC/XMC slots on the ACEX4620/ACEX-4610 carrier boards.
2.0
Ordering Information
ACEX-4600-XXX
XXX = EDK
XXX = DLS
Acromag, Inc. Tel: 248-295-0310
Standalone Engineering Development board for ACEX-46xx Carriers
Engineering Lab System which includes EDK board and mounting plate
with cooling fans.
-6-
www.acromag.com
ACEX-4600-EDK User’s Manual
3.0
COM Express System Development Kit
Preparation For Use
Unpacking and Inspection
Upon receipt of this product, inspect the shipping carton for evidence
of mishandling during transit. If the shipping carton is badly
damaged or water stained, request that the carrier's agent be present
when the carton is opened.
If the carrier's agent is absent when the carton is opened and the
contents of the carton are damaged, keep the carton and packing
material for the agent's inspection.
For repairs to a product damaged in shipment, refer to the Acromag
Service Policy to obtain return instructions. It is suggested that
salvageable shipping cartons and packing material be saved for future
use in the event the product must be shipped.
This board is physically protected with packing material and
electrically protected with an anti-static bag during shipment. It is
recommended that the board be visually inspected for evidence of
mishandling prior to applying power.
The board utilizes static sensitive components and should only be
handled at a static-safe workstation.
IMPORTANT: Adequate air circulation must be provided to prevent a temperature rise above the
maximum operating temperature.
Adequate air circulation must be provided to prevent a temperature
rise above the maximum operating temperature and to prolong the
life of the electronics.
If the installation is in an industrial environment and the board is
exposed to environmental air, careful consideration should be given
to air-filtering.
Acromag, Inc. Tel: 248-295-0310
-7-
www.acromag.com
ACEX-4600-EDK User’s Manual
4.0
COM Express System Development Kit
Operational Block Diagram
Acromag, Inc. Tel: 248-295-0310
-8-
www.acromag.com
ACEX-4600-EDK User’s Manual
5.0
COM Express System Development Kit
Board Layout
The ACEX-4600-EDK has two high-speed SEARAY connectors that are shown on the left side of the board
in the picture above. The larger of the two is a 500-pin connector that can interface with all three
Acromag COM Express carrier models (ACEX-4620/ACEX-4610/ACEX-4605). The carrier passes the
peripheral signals from the COM Express CPU through this connector along with the PMC/XMC Site 1
Rear I/O signals, if applicable. Refer to the manual for the XCOM-6400 COM Express CPU Module for
more information regarding the COM Express CPU peripherals.
The smaller SEARAY connector is a 200-pin connector that is used to interface with the ACEX-4620
double-wide COM Express Carrier. The ACEX-4620 carrier passes the PMC/XMC Site 2 Rear I/O signals
through this connector to the high-speed connectors shown at the bottom of the board in the diagram
above. The single-wide ACEX-4610/ACEX-4605 carriers do not contain a second PMC/XMC Site and
therefore do not make a connection with the 200-pin SEARAY connector.
Acromag, Inc. Tel: 248-295-0310
-9-
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
The COM Express CPU peripherals that are passed along the 500-pin SEARAY connector are brought out
to standard I/O connectors. For video, the ACEX-4600-EDK supports the following three display
configurations:
ACEX-4600-EDK Valid Three-Display Configurations
Display 1
Display 2
Display 3
HDMI
HDMI
DisplayPort
DisplayPort
DisplayPort
DisplayPort
VGA
DisplayPort
HDMI
Maximum Display Resolution
Display 1
Display 2
Display 3
4096x2304 @ 24 Hz
3840x2160 @ 60 Hz
2560x1600 @ 60 Hz
3840x2160 @ 60 Hz
1920x1200 @ 60 Hz
3840x2160 @ 60 Hz
4096x2304 @ 24 Hz
2560x1600 @ 60 Hz
Notes:
1.) Requires support of two channel DDR3L/DDR3L-RS 1600 MT/s configuration for
driving three simultaneous 3840x2160 @60 Hz display resolutions.
2.) DisplayPort resolutions in the above table are supported for four lanes with link
data rate HBR2.
Any 3 displays can be supported simultaneously using the following rules:
 Max of 2 HDMIs
 Any 3 DisplayPort
 One VGA
Acromag, Inc. Tel: 248-295-0310
- 10 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
The ACEX-4600-EDK board contains 3 HDMI connectors, 3 DisplayPort connectors, Line-in and Line-out
audio connectors, a VGA connector, 2 Serial Port connectors, 2 Ethernet connectors, 4 USB 3.0
connectors, and 2 USB 2.0 connectors. There are also high speed connectors that provide access to the
Rear I/O of the two PMC/XMC sites, if applicable. The board contains a PCIe x16 connector that supports
up to 4 lanes. There are 2 SATA ports that allow for the use of SSD or Hard Drive devices. For more
information regarding the COM Express CPU peripherals, refer to the XCOM-6400 manual. The board
also contains 3 standard fan power headers that allow for the use of cooling fans for the system.
The ACEX-4600-EDK provides the carrier board with 10-36VDC which in turn powers the rest of the
system. The user has two options for providing this power. The first is through a standard R7B 4-pin
DIN connector. The table below shows the pinout for this type of connector. In this case +V
corresponds to the 10-36V supply and –V connects to ground. There are two available power supply
models that can be purchased separately for use with the R7B connector. The 5028-562 model is a
160W power supply that provides 24V at 6.67A to the system. The 5028-563 model is a 220W power
supply that provides 24V at 9.2A to the system. The higher power model, 5028-563, is necessary when
the PMC/XMC slots on the carrier are being used to ensure sufficient power to the mezzanine cards.
The second option for providing power is through a 3-pin terminal block and the use of a lab bench
supply. The connections for the terminal block are shown in the table below as well as on the board in
silkscreen.
Pin
1
2
3
Signal
10-36 VDC Power
Ground
Ground
There is an inline fuse located on the input power to protect the circuitry from an overcurrent event.
In the event of a blown fuse, there is a spare fuse located on the lower right side of the board to allow
for easy repair.
CAUTION: POWER MUST NOT BE SUPPLIED TO BOTH CONNECTORS SIMULTANEOUSLY.
Acromag, Inc. Tel: 248-295-0310
- 11 -
www.acromag.com
ACEX-4600-EDK User’s Manual
6.0
COM Express System Development Kit
Connectors
200 – Pin SEARAY Connector – J1
Signal Name
VCC_5V_IN
J24_RIO3_P
J24_RIO3_N
J24_RIO7_P
J24_RIO7_N
J24_RIO10_P
J24_RIO10_N
J24_RIO14_P
J24_RIO14_N
J24_RIO17_P
J24_RIO17_N
J24_RIO21_P
J24_RIO21_N
J24_RIO24_P
J24_RIO24_N
J24_RIO28_P
J24_RIO28_N
J24_RIO31_P
J24_RIO31_N
EXT_PWR_OUT
J24_RIO1_P
J24_RIO1_N
J24_RIO5_P
J24_RIO5_N
J24_RIO8_P
J24_RIO8_N
J24_RIO12_P
J24_RIO12_N
J24_RIO15_P
J24_RIO15_N
J24_RIO19_P
J24_RIO19_N
J24_RIO22_P
J24_RIO22_N
J24_RIO26_P
J24_RIO26_N
J24_RIO29_P
Description
5V Input Voltage
PMC Site 2 Rear I/O Differential Pair "J24_RIO3+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO3-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO7+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO7-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO10+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO10-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO14+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO14-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO17+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO17-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO21+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO21-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO24+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO24-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO28+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO28-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO31+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO31-"
External Output Power
PMC Site 2 Rear I/O Differential Pair "J24_RIO1+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO1-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO5+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO5-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO8+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO8-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO12+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO12-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO15+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO15-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO19+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO19-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO22+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO22-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO26+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO26-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO29+"
Acromag, Inc. Tel: 248-295-0310
- 12 -
Searay Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
www.acromag.com
ACEX-4600-EDK User’s Manual
J24_RIO29_N
RSVD
EXT_PWR_OUT
VCC_3.3V_IN
J24_RIO2_P
J24_RIO2_N
J24_RIO6_P
J24_RIO6_N
J24_RIO9_P
J24_RIO9_N
J24_RIO13_P
J24_RIO13_N
J24_RIO16_P
J24_RIO16_N
J24_RIO20_P
J24_RIO20_N
J24_RIO23_P
J24_RIO23_N
J24_RIO27_P
J24_RIO27_N
J24_RIO30_P
J24_RIO30_N
VCC_12V_IN
J24_RIO0_P
J24_RIO0_N
J24_RIO4_P
J24_RIO4_N
J26_SIO4_P
J26_SIO4_N
J24_RIO11_P
J24_RIO11_N
J26_SIO8_P
J26_SIO8_N
J24_RIO18_P
J24_RIO18_N
J26_SIO12_P
J26_SIO12_N
J24_RIO25_P
J24_RIO25_N
J26_SIO16_P
J26_SIO16_N
COM Express System Development Kit
PMC Site 2 Rear I/O Differential Pair "J24_RIO29-"
Reserved
External Output Power
3.3V Input Voltage
PMC Site 2 Rear I/O Differential Pair "J24_RIO2+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO2-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO6+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO6-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO9+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO9-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO13+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO13-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO16+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO16-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO20+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO20-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO23+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO23-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO27+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO27-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO30+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO30-"
12V Input Voltage
PMC Site 2 Rear I/O Differential Pair "J24_RIO0+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO0-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO4+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO4-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO4+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO4-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO11+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO11-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO8+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO8-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO18+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO18-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO12+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO12-"
PMC Site 2 Rear I/O Differential Pair "J24_RIO25+"
PMC Site 2 Rear I/O Differential Pair "J24_RIO25-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO16+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO16-"
Acromag, Inc. Tel: 248-295-0310
- 13 -
B18
B19
B20
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
www.acromag.com
ACEX-4600-EDK User’s Manual
RSVD
VCC_12V_IN
VCC_3.3V_IN
J26_SIO1_P
J26_SIO1_N
J26_SIO3_P
J26_SIO3_N
J26_SIO5_P
J26_SIO5_N
J26_SIO7_P
J26_SIO7_N
J26_SIO9_P
J26_SIO9_N
J26_SIO11_P
J26_SIO11_N
J26_SIO13_P
J26_SIO13_N
J26_SIO15_P
J26_SIO15_N
J26_SIO17_P
J26_SIO17_N
VCC_5V_IN
J26_SIO0_P
J26_SIO0_N
GND
GND
J26_SIO2_P
J26_SIO2_N
GND
GND
J26_SIO6_P
J26_SIO6_N
GND
GND
J26_SIO10_P
J26_SIO10_N
GND
GND
J26_SIO14_P
J26_SIO14_N
J26_SIO18_P
COM Express System Development Kit
Reserved
12V Input Voltage
3.3V Input Voltage
XMC Site 2 Rear I/O Differential Pair "J26_SIO1+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO1-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO3+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO3-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO5+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO5-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO7+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO7-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO9+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO9-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO11+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO11-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO13+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO13-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO15+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO15-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO17+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO17-"
5V Input Voltage
XMC Site 2 Rear I/O Differential Pair "J26_SIO0+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO0-"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_SIO2+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO2-"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_SIO6+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO6-"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_SIO10+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO10-"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_SIO14+"
XMC Site 2 Rear I/O Differential Pair "J26_SIO14-"
XMC Site 2 Rear I/O Differential Pair "J26_SIO18+"
Acromag, Inc. Tel: 248-295-0310
- 14 -
D19
D20
E1
E2
E3
E4
E5
E6
E7
E8
E9
E10
E11
E12
E13
E14
E15
E16
E17
E18
E19
E20
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
www.acromag.com
ACEX-4600-EDK User’s Manual
J26_SIO18_N
GND
GND
J26_DP17_N
J26_DP17_P
GND
GND
J26_DP13_N
J26_DP13_P
GND
GND
J26_DP09_N
J26_DP09_P
GND
GND
J26_DP05_N
J26_DP05_P
GND
GND
J26_DP01_N
J26_DP01_P
J26_DP19_N
J26_DP19_P
GND
GND
J26_DP15_N
J26_DP15_P
GND
GND
J26_DP11_N
J26_DP11_P
GND
GND
J26_DP07_N
J26_DP07_P
GND
GND
J26_DP03_N
J26_DP03_P
GND
GND
COM Express System Development Kit
XMC Site 2 Rear I/O Differential Pair "J26_SIO18-"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP17-"
XMC Site 2 Rear I/O Differential Pair "J26_DP17+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP13-"
XMC Site 2 Rear I/O Differential Pair "J26_DP13+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP09-"
XMC Site 2 Rear I/O Differential Pair "J26_DP09+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP05-"
XMC Site 2 Rear I/O Differential Pair "J26_DP05+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP01-"
XMC Site 2 Rear I/O Differential Pair "J26_DP01+"
XMC Site 2 Rear I/O Differential Pair "J26_DP19-"
XMC Site 2 Rear I/O Differential Pair "J26_DP19+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP15-"
XMC Site 2 Rear I/O Differential Pair "J26_DP15+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP11-"
XMC Site 2 Rear I/O Differential Pair "J26_DP11+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP07-"
XMC Site 2 Rear I/O Differential Pair "J26_DP07+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP03-"
XMC Site 2 Rear I/O Differential Pair "J26_DP03+"
Ground
Ground
Acromag, Inc. Tel: 248-295-0310
- 15 -
F20
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
H12
H13
H14
H15
H16
H17
H18
H19
H20
www.acromag.com
ACEX-4600-EDK User’s Manual
GND
GND
J26_DP16_N
J26_DP16_P
GND
GND
J26_DP12_N
J26_DP12_P
GND
GND
J26_DP08_N
J26_DP08_P
GND
GND
J26_DP04_N
J26_DP04_P
GND
GND
J26_DP00_N
J26_DP00_P
J26_DP18_N
J26_DP18_P
GND
GND
J26_DP14_N
J26_DP14_P
GND
GND
J26_DP10_N
J26_DP10_P
GND
GND
J26_DP06_N
J26_DP06_P
GND
GND
J26_DP02_N
J26_DP02_P
GND
GND
COM Express System Development Kit
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP16-"
XMC Site 2 Rear I/O Differential Pair "J26_DP16+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP12-"
XMC Site 2 Rear I/O Differential Pair "J26_DP12+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP08-"
XMC Site 2 Rear I/O Differential Pair "J26_DP08+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP04-"
XMC Site 2 Rear I/O Differential Pair "J26_DP04+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP00-"
XMC Site 2 Rear I/O Differential Pair "J26_DP00+"
XMC Site 2 Rear I/O Differential Pair "J26_DP18-"
XMC Site 2 Rear I/O Differential Pair "J26_DP18+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP14-"
XMC Site 2 Rear I/O Differential Pair "J26_DP14+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP10-"
XMC Site 2 Rear I/O Differential Pair "J26_DP10+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP06-"
XMC Site 2 Rear I/O Differential Pair "J26_DP06+"
Ground
Ground
XMC Site 2 Rear I/O Differential Pair "J26_DP02-"
XMC Site 2 Rear I/O Differential Pair "J26_DP02+"
Ground
Ground
Acromag, Inc. Tel: 248-295-0310
- 16 -
J1
J2
J3
J4
J5
J6
J7
J8
J9
J10
J11
J12
J13
J14
J15
J16
J17
J18
J19
J20
K1
K2
K3
K4
K5
K6
K7
K8
K9
K10
K11
K12
K13
K14
K15
K16
K17
K18
K19
K20
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
500 – Pin SEARAY Connector – J2
Signal Name
GND
J14_RIO19_N
J14_RIO19_P
J14_RIO24_P
J14_RIO24_N
J14_RIO20_N
J14_RIO20_P
J14_RIO21_N
J14_RIO21_P
J14_RIO23_P
J14_RIO23_N
J14_RIO25_P
J14_RIO25_N
J14_RIO27_P
J14_RIO27_N
J14_RIO29_P
J14_RIO29_N
J14_RIO31_P
J14_RIO31_N
VCC_12V_IN
USB0_+5V
FAN_TACH
FAN_PWM
PLT_RST#
USB3_+5V
EDP_HPD
EDP_BKLTCTL
EDP_BKLTEN
USB4_+5V
EXT_PWR_OUT
EXT_PWR_OUT
EXT_PWR_OUT
EXT_PWR_OUT
EXT_PWR_OUT
EXT_PWR_OUT
EXT_PWR_OUT
EXT_PWR_OUT
EXT_PWR_OUT
EXT_PWR_OUT
Description
Ground
PMC Site 1 Rear I/O Differential Pair "J14_RIO19-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO19+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO24+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO24-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO20-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO20+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO21-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO21+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO23+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO23-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO25+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO25-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO27+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO27-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO29+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO29-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO31+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO31-"
12V Input Voltage
USB0 Positive 5V from Carrier
CPU Fan Tach Input
CPU Fan Speed Control
Platform Reset Signal
USB3 Positive 5V from Carrier
eDP Hot Plug Detect
eDP Backlight Brightness Control
eDP Backlight Enable
USB4 Positive 5V from Carrier
External Output Power
External Output Power
External Output Power
External Output Power
External Output Power
External Output Power
External Output Power
External Output Power
External Output Power
External Output Power
Acromag, Inc. Tel: 248-295-0310
- 17 -
Searay Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
www.acromag.com
ACEX-4600-EDK User’s Manual
VCC_5V_IN
GND
LINE-OUT_R
AUDIO_GND
LINE-IN_R
LINE-IN_L
GND
GBE0_MDI3_P
GBE0_MDI3_N
GBE1_MDI3_P
GBE1_MDI3_N
J14_RIO18_N
J14_RIO18_P
J14_RIO14_P
J14_RIO14_N
J14_RIO7_N
J14_RIO7_P
J14_RIO10_N
J14_RIO10_P
J14_RIO6_N
J14_RIO6_P
J14_RIO17_P
J14_RIO17_N
J14_RIO22_P
J14_RIO22_N
J14_RIO26_P
J14_RIO26_N
J14_RIO8_P
J14_RIO8_N
GPI_2
GPI_3
USB0_P
USB0_N
GPO_0
GPO_1
USB3_P
USB3_N
GND
GND
USB4_P
USB4_N
COM Express System Development Kit
5V Input Voltage
Ground
Right Channel Audio Line Out from CODEC on Carrier
AUDIO_GND connected to Digital GND near CODEC on Carrier
Right Channel Audio Line In from CODEC on Carrier
Left Channel Audio Line In from CODEC on Carrier
Ground
Gigabit Ethernet Controller 0 from Module - MDI Differential Pair 3 Positive
Gigabit Ethernet Controller 0 from Module - MDI Differential Pair 3 Negative
Gigabit Ethernet Controller 1 from Carrier - MDI Differential Pair 3 Positive
Gigabit Ethernet Controller 1 from Carrier - MDI Differential Pair 3 Negative
PMC Site 1 Rear I/O Differential Pair "J14_RIO18-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO18+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO14+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO14-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO7-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO7+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO10-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO10+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO6-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO6+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO17+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO17-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO22+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO22-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO26+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO26-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO8+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO8-"
General Purpose Input 2
General Purpose Input 3
USB0 Differential Pair - "USB0+"
USB0 Differential Pair - "USB0-"
General Purpose Output 0
General Purpose Output 1
USB3 Differential Pair - "USB3+"
USB3 Differential Pair - "USB3-"
Ground
Ground
USB4 Differential Pair - "USB4+"
USB4 Differential Pair - "USB4-"
Acromag, Inc. Tel: 248-295-0310
- 18 -
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
www.acromag.com
ACEX-4600-EDK User’s Manual
USB5_+5V
DPC_AUX_SEL
UART_TX0_P
UART_TX0_N
UART_RX0_P
UART_RX0_N
UART_TX1_P
UART_TX1_N
UART_RX1_P
UART_RX1_N
VCC_3.3V_IN
LINE-OUT_L
VGA_BLU
VGA_RED
VGA_GRN
GND
GBE0_MDI2_P
GBE0_MDI2_N
GBE1_MDI2_P
GBE1_MDI2_N
WDTO
J14_RIO13_N
J14_RIO13_P
J14_RIO9_N
J14_RIO9_P
J14_RIO5_N
J14_RIO5_P
J14_RIO1_N
J14_RIO1_P
J14_RIO2_N
J14_RIO2_P
J14_RIO28_P
J14_RIO28_N
J14_RIO12_N
J14_RIO12_P
J14_RIO4_P
J14_RIO4_N
J14_RIO30_P
J14_RIO30_N
GPI_1
USB1_+5V
COM Express System Development Kit
USB5 Positive 5V from Carrier
Digital Display Interface 2 - AUX Function Select
General Purpose Serial Port 0 from Carrier Transmitter Positive
General Purpose Serial Port 0 from Carrier Transmitter Negative
General Purpose Serial Port 0 from Carrier Receiver Positive
General Purpose Serial Port 0 from Carrier Receiver Negative
General Purpose Serial Port 1 from Carrier Transmitter Positive
General Purpose Serial Port 1 from Carrier Transmitter Negative
General Purpose Serial Port 1 from Carrier Receiver Positive
General Purpose Serial Port 1 from Carrier Receiver Negative
3.3V Input Voltage
Left Channel Audio Line Out from CODEC on Carrier
Analog Video Output Blue
Analog Video Output Red
Analog Video Output Green
Ground
Gigabit Ethernet Controller 0 from Module - MDI Differential Pair 2 Positive
Gigabit Ethernet Controller 0 from Module - MDI Differential Pair 2 Negative
Gigabit Ethernet Controller 1 from Carrier - MDI Differential Pair 2 Positive
Gigabit Ethernet Controller 1 from Carrier - MDI Differential Pair 2 Negative
Watchdog Timer Output
PMC Site 1 Rear I/O Differential Pair "J14_RIO13-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO13+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO9-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO9+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO5-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO5+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO1-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO1+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO2-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO2+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO28+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO28-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO12-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO12+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO4+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO4-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO30+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO30-"
General Purpose Input 1
USB1 Positive 5V from Carrier
Acromag, Inc. Tel: 248-295-0310
- 19 -
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B50
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
www.acromag.com
ACEX-4600-EDK User’s Manual
EDP_VDDEN
EDP_TX3_N
EDP_TX3_P
GND
GND
DPC_TX3_N
DPC_TX3_P
GND
GND
USB5_P
USB5_N
DPC_HPD
THRMTRIP3#
SPKR
BATLOW#
SUS_STAT#
VCC_5V_IN
VCC_5V_IN
SATA_ACT#
VCC_3.3V_IN
GND
GND
GND
GND
VGA_I2C_DAT
GBE0_MDI1_P
GBE0_MDI1_N
GBE1_MDI1_P
GBE1_MDI1_N
J14_RIO15_N
J14_RIO15_P
J14_RIO11_N
J14_RIO11_P
J16_SIO1_N
J16_SIO1_P
J14_RIO3_N
J14_RIO3_P
J16_SIO8_P
J16_SIO8_N
J14_RIO16_N
J14_RIO16_P
COM Express System Development Kit
eDP Power Enable
eDP Differential Pair 3 Negative
eDP Differential Pair 3 Positive
Ground
Ground
Digital Display Interface 2 - Output Differential Pair 3 Negative
Digital Display Interface 2 - Output Differential Pair 3 Positive
Ground
Ground
USB5 Differential Pair - "USB5+"
USB5 Differential Pair - "USB5-"
Digital Display Interface 2 - Hot Plug Detect
Output Signal Indicating CPU Entered Thermal Shutdown
Audio Enunciator Output - PC Beep Signal
Low Battery Indicator for External Battery
Imminent Suspend Operation Indicator - Notifies LPC Devices
5V Input Voltage
5V Input Voltage
ATA (Parallel and Serial) or SAS Activity Indicator Signal
3.3V Input Voltage
Ground
Ground
Ground
Ground
Display Data Channel (DDC) Data Line
Gigabit Ethernet Controller 0 from Module - MDI Differential Pair 1 Positive
Gigabit Ethernet Controller 0 from Module - MDI Differential Pair 1 Negative
Gigabit Ethernet Controller 1 from Carrier - MDI Differential Pair 1 Positive
Gigabit Ethernet Controller 1 from Carrier - MDI Differential Pair 1 Negative
PMC Site 1 Rear I/O Differential Pair "J14_RIO15-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO15+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO11-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO11+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO1-"
XMC Site 1 Rear I/O Differential Pair "J16_SIO1+"
PMC Site 1 Rear I/O Differential Pair "J14_RIO3-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO3+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO8+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO8-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO16-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO16+"
Acromag, Inc. Tel: 248-295-0310
- 20 -
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
C33
C34
C35
C36
C37
C38
C39
C40
C41
C42
C43
C44
C45
C46
C47
C48
C49
C50
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
www.acromag.com
ACEX-4600-EDK User’s Manual
J16_SIO12_P
J16_SIO12_N
J14_RIO0_N
J14_RIO0_P
J16_SIO16_P
J16_SIO16_N
GPI_0
GPO_3
USB1_P
USB1_N
GND
GND
EDP_TX1_N
EDP_TX1_P
GND
GND
DPC_TX0_N
DPC_TX0_P
GND
GND
DPD_AUX_SEL
DPD_HPD
COM_THRM#
DPB_AUX_SEL
DPB_HPD
SLP_S5#
SLP_S4#
SLP_S3#
LPC_DRQ1#
LPC_DRQ0#
VCC_3.3V_IN
VGA_VSYNC
VGA_HSYNC
VGA_I2C_CK
GBE0_MDI0_P
GBE0_MDI0_N
GBE1_MDI0_P
GBE1_MDI0_N
SYSRST#
J16_SIO2_N
J16_SIO2_P
COM Express System Development Kit
XMC Site 1 Rear I/O Differential Pair "J16_SIO12+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO12-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO0-"
PMC Site 1 Rear I/O Differential Pair "J14_RIO0+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO16+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO16-"
General Purpose Input 0
General Purpose Output 3
USB1 Differential Pair - "USB1+"
USB1 Differential Pair - "USB1-"
Ground
Ground
eDP Differential Pair 1 Negative
eDP Differential Pair 1 Positive
Ground
Ground
Digital Display Interface 2 - Output Differential Pair 0 Negative
Digital Display Interface 2 - Output Differential Pair 0 Positive
Ground
Ground
Digital Display Interface 3 - AUX Function Select
Digital Display Interface 3 - Hot Plug Detect
Off-Module Temp Sensor Input Signal Indicating Over-Temp Condition
Digital Display Interface 1 - AUX Function Select
Digital Display Interface 1 - Hot Plug Detect
Output Signal Indicating Soft Off State
Output Signal Indicating Suspend to Disk State
Output Signal Indicating Suspend to RAM State
LPC Serial DMA Request Signal 1
LPC Serial DMA Request Signal 0
3.3V Input Voltage
VGA Output Vertical Sync
VGA Output Horizontal Sync
Display Data Channel (DDC) Clock Line
Gigabit Ethernet Controller 0 from Module - MDI Differential Pair 0 Positive
Gigabit Ethernet Controller 0 from Module - MDI Differential Pair 0 Negative
Gigabit Ethernet Controller 1 from Carrier - MDI Differential Pair 0 Positive
Gigabit Ethernet Controller 1 from Carrier - MDI Differential Pair 0 Negative
System Reset Signal
XMC Site 1 Rear I/O Differential Pair "J16_SIO2-"
XMC Site 1 Rear I/O Differential Pair "J16_SIO2+"
Acromag, Inc. Tel: 248-295-0310
- 21 -
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
D32
D33
D34
D35
D36
D37
D38
D39
D40
D41
D42
D43
D44
D45
D46
D47
D48
D49
D50
E1
E2
E3
www.acromag.com
ACEX-4600-EDK User’s Manual
J16_SIO3_P
J16_SIO3_N
J16_DP16_N
J16_DP16_P
J16_DP19_P
J16_DP19_N
J16_SIO9_P
J16_SIO9_N
J16_SIO0_GCLK_P
J16_SIO0_GCLK_N
J16_SIO13_P
J16_SIO13_N
J16_SIO15_P
J16_SIO15_N
J16_SIO17_P
J16_SIO17_N
GPO_2
USB2_+5V
GND
EDP_TX0_N
EDP_TX0_P
GND
GND
DPC_TX2_N
DPC_TX2_P
GND
GND
DPC_CTRL_AUX_N
DPC_CTRL_AUX_P
GND
GND
I2C_DAT
I2C_CLK
GND
GND
SMB_DATA
SMB_CLK
SMB_ALERT#
LPC_SERIRQ
LPC_FRAME#
VCC_3.3V_IN
COM Express System Development Kit
XMC Site 1 Rear I/O Differential Pair "J16_SIO3+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO3-"
XMC Site 1 Rear I/O Differential Pair "J16_DP16-"
XMC Site 1 Rear I/O Differential Pair "J16_DP16+"
XMC Site 1 Rear I/O Differential Pair "J16_DP19+"
XMC Site 1 Rear I/O Differential Pair "J16_DP19-"
XMC Site 1 Rear I/O Differential Pair "J16_SIO9+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO9-"
XMC Site 1 Rear I/O Differential Pair "J16_SIO0+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO0-"
XMC Site 1 Rear I/O Differential Pair "J16_SIO13+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO13-"
XMC Site 1 Rear I/O Differential Pair "J16_SIO15+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO15-"
XMC Site 1 Rear I/O Differential Pair "J16_SIO17+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO17-"
General Purpose Output 2
USB2 Positive 5V from Carrier
Ground
eDP Differential Pair 0 Negative
eDP Differential Pair 0 Positive
Ground
Ground
Differential Pair - "DDI2_PAIR2-"
Differential Pair - "DDI2_PAIR2+"
Ground
Ground
Digital Display Interface 2 - DVI/HDMI/DP AUX Control Negative
Digital Display Interface 2 - DVI/HDMI/DP AUX Control Positive
Ground
Ground
General Purpose I2C Port Data I/O Line
General Purpose I2C Port Clock Output
Ground
Ground
System Management Bus Bidirectional Data Line
System Management Bus Bidirectional Clock Line
System Management Bus Alert Signal
LPC Serial Interrupt Signal
LPC Frame Signal - LPC Cycle Start Indicator
3.3V Input Voltage
Acromag, Inc. Tel: 248-295-0310
- 22 -
E4
E5
E6
E7
E8
E9
E10
E11
E12
E13
E14
E15
E16
E17
E18
E19
E20
E21
E22
E23
E24
E25
E26
E27
E28
E29
E30
E31
E32
E33
E34
E35
E36
E37
E38
E39
E40
E41
E42
E43
E44
www.acromag.com
ACEX-4600-EDK User’s Manual
LPC_AD1
LPC_AD0
GBE0_L1000#
GBE1_1V9
GBE0_LINK#
GBE1_LINK#
J16_DP17_N
J16_DP17_P
GND
GND
J16_DP11_N
J16_DP11_P
GND
GND
J16_DP07_N
J16_DP07_P
GND
GND
J16_SIO10_P
J16_SIO10_N
GND
GND
J16_DP02_N
J16_DP02_P
J16_DP00_N
J16_DP00_P
USB2_P
USB2_N
GND
GND
EDP_TX2_N
EDP_TX2_P
GND
GND
DPC_TX1_N
DPC_TX1_P
GND
GND
DPD_CTRL_AUX_N
DPD_CTRL_AUX_P
GND
COM Express System Development Kit
LPC Multiplexed Address - Command and Data Bus 1
LPC Multiplexed Address - Command and Data Bus 0
Gigabit Ethernet Controller 0 from Module - 1000 Mb/s Link Indicator
External 1.9V Reference Voltage from Carrier for Gigabit Ethernet Controller 1
Gigabit Ethernet Controller 0 from Module - Link Indicator
Gigabit Ethernet Controller 1 from Carrier - Link Indicator
XMC Site 1 Rear I/O Differential Pair "J16_DP17-"
XMC Site 1 Rear I/O Differential Pair "J16_DP17+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP11-"
XMC Site 1 Rear I/O Differential Pair "J16_DP11+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP07-"
XMC Site 1 Rear I/O Differential Pair "J16_DP07+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_SIO10+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO10-"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP02-"
XMC Site 1 Rear I/O Differential Pair "J16_DP02+"
XMC Site 1 Rear I/O Differential Pair "J16_DP00-"
XMC Site 1 Rear I/O Differential Pair "J16_DP00+"
USB2 Differential Pair - "USB2+"
USB2 Differential Pair - "USB2-"
Ground
Ground
eDP Differential Pair 2 Negative
eDP Differential Pair 2 Positive
Ground
Ground
Digital Display Interface 2 - Output Differential Pair 1 Negative
Digital Display Interface 2 - Output Differential Pair 1 Positive
Ground
Ground
Digital Display Interface 3 - DVI/HDMI/DP AUX Control Negative
Digital Display Interface 3 - DVI/HDMI/DP AUX Control Positive
Ground
Acromag, Inc. Tel: 248-295-0310
- 23 -
E45
E46
E47
E48
E49
E50
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
www.acromag.com
ACEX-4600-EDK User’s Manual
GND
DPB_CTRL_AUX_N
DPB_CTRL_AUX_P
GND
GND
PWRBTN#
LPC_CLK
GND
GND
LPC_AD3
LPC_AD2
GND
GND
GBE0_ACT#
GBE1_ACT#
GND
GND
J16_SIO5_P
J16_SIO5_N
GND
GND
J16_DP08_N
J16_DP08_P
GND
GND
J16_DP09_N
J16_DP09_P
GND
GND
J16_DP05_N
J16_DP05_P
GND
GND
J16_DP01_N
J16_DP01_P
WAKE1#
WAKE0#
PCIE0_RX_N
PCIE0_RX_P
GND
GND
COM Express System Development Kit
Ground
Digital Display Interface 1 - DVI/HDMI/DP AUX Control Negative
Digital Display Interface 1 - DVI/HDMI/DP AUX Control Positive
Ground
Ground
Power Button Input Signal
LPC Clock Output - 33MHz Nominal
Ground
Ground
LPC Multiplexed Address - Command and Data Bus 3
LPC Multiplexed Address - Command and Data Bus 2
Ground
Ground
Gigabit Ethernet Controller 0 from Module - Activity Indicator
Gigabit Ethernet Controller 1 from Carrier - Activity Indicator
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_SIO5+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO5-"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP08-"
XMC Site 1 Rear I/O Differential Pair "J16_DP08+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP09-"
XMC Site 1 Rear I/O Differential Pair "J16_DP09+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP05-"
XMC Site 1 Rear I/O Differential Pair "J16_DP05+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP01-"
XMC Site 1 Rear I/O Differential Pair "J16_DP01+"
General Purpose Wake Signal
PCI Express Wake Signal
PCI Express Lane 0 Receive Differential Pair Negative
PCI Express Lane 0 Receive Differential Pair Positive
Ground
Ground
Acromag, Inc. Tel: 248-295-0310
- 24 -
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
F49
F50
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
G24
G25
G26
www.acromag.com
ACEX-4600-EDK User’s Manual
PCIE2_RX_N
PCIE2_RX_P
GND
GND
DPD_TX3_N
DPD_TX3_P
GND
GND
DPB_TX3_N
DPB_TX3_P
GND
GND
SATA1_RX_N
SATA1_RX_P
GND
GND
USB3_SSRX_P
USB3_SSRX_N
GND
GND
USB1_SSRX_P
USB1_SSRX_N
GND
GND
J16_DP15_N
J16_DP15_P
GND
GND
J16_DP13_N
J16_DP13_P
GND
GND
J16_SIO11_P
J16_SIO11_N
GND
GND
J16_DP04_N
J16_DP04_P
GND
GND
J16_SIO6_N
COM Express System Development Kit
PCI Express Lane 2 Receive Differential Pair Negative
PCI Express Lane 2 Receive Differential Pair Positive
Ground
Ground
Digital Display Interface 3 - Output Differential Pair 3 Negative
Digital Display Interface 3 - Output Differential Pair 3 Positive
Ground
Ground
Digital Display Interface 1 - Output Differential Pair 3 Negative
Digital Display Interface 1 - Output Differential Pair 3 Positive
Ground
Ground
SATA1 Receive Differential Pair Negative
SATA1 Receive Differential Pair Positive
Ground
Ground
USB3 USB 3.0 SuperSpeed Receive Positive
USB3 USB 3.0 SuperSpeed Receive Negative
Ground
Ground
USB1 USB 3.0 SuperSpeed Receive Positive
USB1 USB 3.0 SuperSpeed Receive Negative
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP15-"
XMC Site 1 Rear I/O Differential Pair "J16_DP15+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP13-"
XMC Site 1 Rear I/O Differential Pair "J16_DP13+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_SIO11+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO11-"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP04-"
XMC Site 1 Rear I/O Differential Pair "J16_DP04+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_SIO6-"
Acromag, Inc. Tel: 248-295-0310
- 25 -
G27
G28
G29
G30
G31
G32
G33
G34
G35
G36
G37
G38
G39
G40
G41
G42
G43
G44
G45
G46
G47
G48
G49
G50
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
H12
H13
H14
H15
H16
H17
www.acromag.com
ACEX-4600-EDK User’s Manual
J16_SIO6_P
GND
GND
EDP_AUX_N
EDP_AUX_P
GND
GND
PCIE0_TX_N
PCIE0_TX_P
GND
GND
PCIE2_TX_N
PCIE2_TX_P
GND
GND
DPD_TX0_N
DPD_TX0_P
GND
GND
DPB_TX0_N
DPB_TX0_P
GND
GND
SATA1_TX_N
SATA1_TX_P
GND
GND
USB3_SSTX_P
USB3_SSTX_N
GND
GND
USB1_SSTX_P
USB1_SSTX_N
GND
GND
J16_SIO7_P
J16_SIO7_N
GND
GND
J16_SIO4_P
J16_SIO4_N
COM Express System Development Kit
XMC Site 1 Rear I/O Differential Pair "J16_SIO6+"
Ground
Ground
eDP AUX Signal Negative
eDP AUX Signal Positive
Ground
Ground
PCI Express Lane 0 Transmit Differential Pair Negative
PCI Express Lane 0 Transmit Differential Pair Positive
Ground
Ground
PCI Express Lane 2 Transmit Differential Pair Negative
PCI Express Lane 2 Transmit Differential Pair Positive
Ground
Ground
Digital Display Interface 3 - Output Differential Pair 0 Negative
Digital Display Interface 3 - Output Differential Pair 0 Positive
Ground
Ground
Digital Display Interface 1 - Output Differential Pair 0 Negative
Digital Display Interface 1 - Output Differential Pair 0 Positive
Ground
Ground
SATA1 Transmit Differential Pair Negative
SATA1 Transmit Differential Pair Positive
Ground
Ground
USB3 USB 3.0 SuperSpeed Transmit Positive
USB3 USB 3.0 SuperSpeed Transmit Negative
Ground
Ground
USB1 USB 3.0 SuperSpeed Transmit Positive
USB1 USB 3.0 SuperSpeed Transmit Negative
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_SIO7+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO7-"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_SIO4+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO4-"
Acromag, Inc. Tel: 248-295-0310
- 26 -
H18
H19
H20
H21
H22
H23
H24
H25
H26
H27
H28
H29
H30
H31
H32
H33
H34
H35
H36
H37
H38
H39
H40
H41
H42
H43
H44
H45
H46
H47
H48
H49
H50
J1
J2
J3
J4
J5
J6
J7
J8
www.acromag.com
ACEX-4600-EDK User’s Manual
GND
GND
J16_DP06_N
J16_DP06_P
GND
GND
J16_DP03_N
J16_DP03_P
GND
GND
J16_DP12_N
J16_DP12_P
GND
GND
PCIE1_RX_N
PCIE1_RX_P
GND
GND
PCIE3_RX_N
PCIE3_RX_P
GND
GND
DPD_TX2_N
DPD_TX2_P
GND
GND
DPB_TX2_N
DPB_TX2_P
GND
GND
SATA0_RX_N
SATA0_RX_P
GND
GND
USB2_SSRX_P
USB2_SSRX_N
GND
GND
USB0_SSRX_P
USB0_SSRX_N
GND
COM Express System Development Kit
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP06-"
XMC Site 1 Rear I/O Differential Pair "J16_DP06+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP03-"
XMC Site 1 Rear I/O Differential Pair "J16_DP03+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP12-"
XMC Site 1 Rear I/O Differential Pair "J16_DP12+"
Ground
Ground
PCI Express Lane 1 Receive Differential Pair Negative
PCI Express Lane 1 Receive Differential Pair Positive
Ground
Ground
PCI Express Lane 3 Receive Differential Pair Negative
PCI Express Lane 3 Receive Differential Pair Positive
Ground
Ground
Digital Display Interface 3 - Output Differential Pair 2 Negative
Digital Display Interface 3 - Output Differential Pair 2 Positive
Ground
Ground
Digital Display Interface 1 - Output Differential Pair 2 Negative
Digital Display Interface 1 - Output Differential Pair 2 Positive
Ground
Ground
SATA0 Receive Differential Pair Negative
SATA0 Receive Differential Pair Positive
Ground
Ground
USB2 USB 3.0 SuperSpeed Receive Positive
USB2 USB 3.0 SuperSpeed Receive Negative
Ground
Ground
USB0 USB 3.0 SuperSpeed Receive Positive
USB0 USB 3.0 SuperSpeed Receive Negative
Ground
Acromag, Inc. Tel: 248-295-0310
- 27 -
J9
J10
J11
J12
J13
J14
J15
J16
J17
J18
J19
J20
J21
J22
J23
J24
J25
J26
J27
J28
J29
J30
J31
J32
J33
J35
J35
J36
J37
J38
J39
J40
J41
J42
J43
J44
J45
J46
J47
J48
J49
www.acromag.com
ACEX-4600-EDK User’s Manual
GND
J16_DP18_N
J16_DP18_P
GND
GND
J16_DP14_N
J16_DP14_P
GND
GND
J16_DP10_N
J16_DP10_P
GND
GND
J16_SIO14_P
J16_SIO14_N
GND
GND
J16_SIO18_GCLK_P
J16_SIO18_GCLK_N
GND
GND
CLK_PEG_N
CLK_PEG_P
GND
GND
PCIE1_TX_P
PCIE1_TX_N
GND
GND
PCIE3_TX_N
PCIE3_TX_P
GND
GND
DPD_TX1_N
DPD_TX1_P
GND
GND
DPB_TX1_N
DPB_TX1_P
GND
GND
COM Express System Development Kit
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP18-"
XMC Site 1 Rear I/O Differential Pair "J16_DP18+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP14-"
XMC Site 1 Rear I/O Differential Pair "J16_DP14+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_DP10-"
XMC Site 1 Rear I/O Differential Pair "J16_DP10+"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_SIO14+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO14-"
Ground
Ground
XMC Site 1 Rear I/O Differential Pair "J16_SIO18+"
XMC Site 1 Rear I/O Differential Pair "J16_SIO18-"
Ground
Ground
PCIe/PEG Reference Clock Output Negative
PCIe/PEG Reference Clock Output Positive
Ground
Ground
PCI Express Lane 1 Transmit Differential Pair Positive
PCI Express Lane 1 Transmit Differential Pair Negative
Ground
Ground
PCI Express Lane 3 Transmit Differential Pair Negative
PCI Express Lane 3 Transmit Differential Pair Positive
Ground
Ground
Digital Display Interface 3 - Output Differential Pair 1 Negative
Digital Display Interface 3 - Output Differential Pair 1 Positive
Ground
Ground
Digital Display Interface 1 - Output Differential Pair 1 Negative
Digital Display Interface 1 - Output Differential Pair 1 Positive
Ground
Ground
Acromag, Inc. Tel: 248-295-0310
- 28 -
J50
K1
K2
K3
K4
K5
K6
K7
K8
K9
K10
K11
K12
K13
K14
K15
K16
K17
K18
K19
K20
K21
K22
K23
K24
K25
K26
K27
K28
K29
K30
K31
K32
K33
K34
K35
K36
K37
K38
K39
K40
www.acromag.com
ACEX-4600-EDK User’s Manual
SATA0_TX_N
SATA0_TX_P
GND
GND
USB2_SSTX_P
USB2_SSTX_N
GND
GND
USB0_SSTX_P
USB0_SSTX_N
COM Express System Development Kit
SATA0 Transmit Differential Pair Negative
SATA0 Transmit Differential Pair Positive
Ground
Ground
USB2 USB 3.0 SuperSpeed Transmit Positive
USB2 USB 3.0 SuperSpeed Transmit Negative
Ground
Ground
USB0 USB 3.0 SuperSpeed Transmit Positive
USB0 USB 3.0 SuperSpeed Transmit Negative
Acromag, Inc. Tel: 248-295-0310
- 29 -
K41
K42
K43
K44
K45
K46
K47
K48
K49
K50
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
DisplayPort 1 Connector – P10
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Description
DPB_LANE0_P
GND
DPB_LANE0_N
DPB_LANE1_P
GND
DPB_LANE1_N
DPB_LANE2_P
GND
DPB_LANE2_N
DPB_LANE3_P
GND
DPB_LANE3_N
Config1 (GND)
Config2 (GND)
DPB_AUX_CH_P
GND
DPB_AUX_CH_N
DPB_HPD
PWR_RTN (GND)
DPB_PWR
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Description
DPC_LANE0_P
GND
DPC_LANE0_N
DPC_LANE1_P
GND
DPC_LANE1_N
DPC_LANE2_P
GND
DPC_LANE2_N
DPC_LANE3_P
GND
DPC_LANE3_N
Config1 (GND)
Config2 (GND)
DPC_AUX_CH_P
GND
DPC_AUX_CH_N
DPC_HPD
PWR_RTN (GND)
DPC_PWR
DisplayPort 2 Connector – P12
Acromag, Inc. Tel: 248-295-0310
- 30 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
DisplayPort 3 Connector – P18
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Description
DPD_LANE0_P
GND
DPD_LANE0_N
DPD_LANE1_P
GND
DPD_LANE1_N
DPD_LANE2_P
GND
DPD_LANE2_N
DPD_LANE3_P
GND
DPD_LANE3_N
Config1 (GND)
Config2 (GND)
DPD_AUX_CH_P
GND
DPD_AUX_CH_N
DPD_HPD
PWR_RTN (GND)
DPD_PWR
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Description
DPB_TMDS_D2_P
GND
DPB_TMDS_D2_N
DPB_TMDS_D1_P
GND
DPB_TMDS_D1_N
DPB_TMDS_D0_P
GND
DPB_TMDS_D0_N
DPB_TMDS_CLK_P
GND
DPB_TMDS_CLK_N
NC
NC
DPB_SERIAL_CLK
DPB_SERIAL_DATA
GND
DPB_HDMI_PWR
DPB_TMDS_HPD
HDMI 1 Connector – P9
Acromag, Inc. Tel: 248-295-0310
- 31 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
HDMI 2 Connector – P11
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Description
DPC_TMDS_D2_P
GND
DPC_TMDS_D2_N
DPC_TMDS_D1_P
GND
DPC_TMDS_D1_N
DPC_TMDS_D0_P
GND
DPC_TMDS_D0_N
DPC_TMDS_CLK_P
GND
DPC_TMDS_CLK_N
NC
NC
DPC_SERIAL_CLK
DPC_SERIAL_DATA
GND
DPC_HDMI_PWR
DPC_TMDS_HPD
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Description
DPD_TMDS_D2_P
GND
DPD_TMDS_D2_N
DPD_TMDS_D1_P
GND
DPD_TMDS_D1_N
DPD_TMDS_D0_P
GND
DPD_TMDS_D0_N
DPD_TMDS_CLK_P
GND
DPD_TMDS_CLK_N
NC
NC
DPD_SERIAL_CLK
DPD_SERIAL_DATA
GND
DPD_HDMI_PWR
DPD_TMDS_HPD
HDMI 3 Connector – P17
Acromag, Inc. Tel: 248-295-0310
- 32 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
COM 1 RS-232/485 Connector – P19A (Bottom)
Pin Number
1
2
3
4
5
6
7
8
9
Description
NC
UART_RX0_P
UART_TX0_P
UART_TX0_N
GND
UART_RX0_N
NC
NC
NC
COM 2 RS-232/485 Connector – P19B (Top)
Pin Number
1
2
3
4
5
6
7
8
9
Description
NC
UART_RX1_P
UART_TX1_P
UART_TX1_N
GND
UART_RX1_N
NC
NC
NC
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Description
VGA_RED
VGA_GRN
VGA_BLU
NC
GND
RGND
GGND
BGND
+5V PWR
SGND
NC
VGA_I2C_DAT
VGA_HSYNC
VGA_VSYNC
VGA_I2C_CLK
VGA Connector – J14
Acromag, Inc. Tel: 248-295-0310
- 33 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
XMC Rear I/O Site 1 Connector – P6
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Acromag, Inc. Tel: 248-295-0310
Description
J16_DPO0_P
J16_DPO10_P
J16_DPO0_N
J16_DPO10_N
J16_DPO1_P
J16_DPO11_P
J16_DPO1_N
J16_DPO11_N
J16_DPO2_P
J16_DPO12_P
J16_DPO2_N
J16_DPO12_N
J16_DPO3_P
J16_DPO13_P
J16_DPO3_N
J16_DPO13_N
J16_DPO8_P
J16_DPO9_P
J16_DPO8_N
J16_DPO9_N
J16_SIO0_GCLK_P
J16_SIO1_P
J16_SIO0_GCLK_N
J16_SIO1_N
J16_SIO2_P
J16_SIO3_P
J16_SIO2_N
J16_SIO3_N
J16_SIO4_P
J16_SIO5_P
J16_SIO4_N
J16_SIO5_N
J16_SIO6_P
J16_SIO7_P
J16_SIO6_N
J16_SIO7_N
J16_SIO8_P
J16_SIO9_P
J16_SIO8_N
J16_SIO9_N
- 34 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
XMC Rear I/O Site 1 Connector – P8
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
*17 (see note)
18
*19 (see Note)
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Description
J16_DP04_P
J16_DP14_P
J16_DP04_N
J16_DP14_N
J16_DP05_P
J16_DP15_P
J16_DP05_N
J16_DP15_N
J16_DP06_P
J16_DP16_P
J16_DP06_N
J16_DP16_N
J16_DP07_P
J16_DP17_P
J16_DP07_N
J16_DP17_N
J16_DP18_N / J16_DP18_P
J16_DP19_P
J16_DP18_P / J16_DP18_N
J16_DP19_N
J16_SIO10_P
J16_SIO11_P
J16_SIO10_N
J16_SIO11_N
J16_SIO12_P
J16_SIO13_P
J16_SIO12_N
J16_SIO13_N
J16_SIO14_P
J16_SIO15_P
J16_SIO14_N
J16_SIO15_N
J16_SIO16_P
J16_SIO18_GCLK_P
J16_SIO16_N
J16_SIO18_GCLK_N
J16_SIO17_P
NC
J16_SIO17_N
NC
Note:
* Pin 17 and Pin 19 signals are swapped on ACEX-4600-EDK Rev. B. The signal name shown in red is for
future revisions (Rev. C and above).
Acromag, Inc. Tel: 248-295-0310
- 35 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
XMC Rear I/O Site 2 Connector – P5
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Acromag, Inc. Tel: 248-295-0310
Description
J26_DPO0_P
J26_DPO10_P
J26_DPO0_N
J26_DPO10_N
J26_DPO1_P
J26_DPO11_P
J26_DPO1_N
J26_DPO11_N
J26_DPO2_P
J26_DPO12_P
J26_DPO2_N
J26_DPO12_N
J26_DPO3_P
J26_DPO13_P
J26_DPO3_N
J26_DPO13_N
J26_DPO8_P
J26_DPO9_P
J26_DPO8_N
J26_DPO9_N
J26_SIO0_GCLK_P
J26_SIO1_P
J26_SIO0_GCLK_N
J26_SIO1_N
J26_SIO2_P
J26_SIO3_P
J26_SIO2_N
J26_SIO3_N
J26_SIO4_P
J26_SIO5_P
J26_SIO4_N
J26_SIO5_N
J26_SIO6_P
J26_SIO7_P
J26_SIO6_N
J26_SIO7_N
J26_SIO8_P
J26_SIO9_P
J26_SIO8_N
J26_SIO9_N
- 36 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
XMC Rear I/O Site 1 Connector – P7
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
*17 (See Note)
18
*19 (See Note)
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Description
J26_DP04_P
J26_DP14_P
J26_DP04_N
J26_DP14_N
J26_DP05_P
J26_DP15_P
J26_DP05_N
J26_DP15_N
J26_DP06_P
J26_DP16_P
J26_DP06_N
J26_DP16_N
J26_DP07_P
J26_DP17_P
J26_DP07_N
J26_DP17_N
J26_DP18_N / J26_DP18_P
J26_DP19_P
J26_DP18_P / J26_DP18_N
J26_DP19_N
J26_SIO10_P
J26_SIO11_P
J26_SIO10_N
J26_SIO11_N
J26_SIO12_P
J26_SIO13_P
J26_SIO12_N
J26_SIO13_N
J26_SIO14_P
J26_SIO15_P
J26_SIO14_N
J26_SIO15_N
J26_SIO16_P
J26_SIO18_GCLK_P
J26_SIO16_N
J26_SIO18_GCLK_N
J26_SIO17_P
NC
J26_SIO17_N
NC
Note:
* Pin 17 and Pin 19 signals are swapped on ACEX-4600-EDK Rev. B. The signal name shown in red is for
future revisions (Rev. C and above).
Acromag, Inc. Tel: 248-295-0310
- 37 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
PMC Rear I/O Site 1 Connector – J7
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Acromag, Inc. Tel: 248-295-0310
Description
J14_RIO0_P
J14_RIO1_P
J14_RIO2_P
J14_RIO3_P
J14_RIO4_P
J14_RIO5_P
J14_RIO6_P
J14_RIO7_P
J14_RIO8_P
J14_RIO9_P
J14_RIO10_P
GND
J14_RIO11_P
J14_RIO12_P
J14_RIO13_P
J14_RIO14_P
J14_RIO15_P
J14_RIO16_P
J14_RIO17_P
J14_RIO18_P
J14_RIO19_P
J14_RIO20_P
GND
J14_RIO21_P
J14_RIO22_P
J14_RIO23_P
J14_RIO24_P
J14_RIO25_P
J14_RIO26_P
J14_RIO27_P
J14_RIO28_P
J14_RIO29_P
J14_RIO30_P
J14_RIO31_P
- 38 -
Pin Number
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Description
J14_RIO0_N
J14_RIO1_N
J14_RIO2_N
J14_RIO3_N
J14_RIO4_N
J14_RIO5_N
J14_RIO6_N
14_RIO7_N
J14_RIO8_N
J14_RIO9_N
J14_RIO10_N
GND
J14_RIO11_N
J14_RIO12_N
J14_RIO13_N
J14_RIO14_N
J14_RIO15_N
J14_RIO16_N
J14_RIO17_N
J14_RIO18_N
J14_RIO19_N
J14_RIO20_N
GND
J14_RIO21_N
J14_RIO22_N
J14_RIO23_N
J14_RIO24_N
J14_RIO25_N
J14_RIO26_N
J14_RIO27_N
J14_RIO28_N
J14_RIO29_N
J14_RIO30_N
J14_RIO31_N
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
PMC Rear I/O Site 2 Connector – J6
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Acromag, Inc. Tel: 248-295-0310
Description
J24_RIO0_P
J24_RIO1_P
J24_RIO2_P
J24_RIO3_P
J24_RIO4_P
J24_RIO5_P
J24_RIO6_P
J24_RIO7_P
J24_RIO8_P
J24_RIO9_P
J24_RIO10_P
GND
J24_RIO11_P
J24_RIO12_P
J24_RIO13_P
J24_RIO14_P
J24_RIO15_P
J24_RIO16_P
J24_RIO17_P
J24_RIO18_P
J24_RIO19_P
J24_RIO20_P
GND
J24_RIO21_P
J24_RIO22_P
J24_RIO23_P
J24_RIO24_P
J24_RIO25_P
J24_RIO26_P
J24_RIO27_P
J24_RIO28_P
J24_RIO29_P
J24_RIO30_P
J24_RIO31_P
- 39 -
Pin Number
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Description
J24_RIO0_N
J24_RIO1_N
J24_RIO2_N
J24_RIO3_N
J24_RIO4_N
J24_RIO5_N
J24_RIO6_N
J24_RIO7_N
J24_RIO8_N
J24_RIO9_N
J24_RIO10_N
GND
J24_RIO11_N
J24_RIO12_N
J24_RIO13_N
J24_RIO14_N
J24_RIO15_N
J24_RIO16_N
J24_RIO17_N
J24_RIO18_N
J24_RIO19_N
J24_RIO20_N
GND
J24_RIO21_N
J24_RIO22_N
J24_RIO23_N
J24_RIO24_N
J24_RIO25_N
J24_RIO26_N
J24_RIO27_N
J24_RIO28_N
J24_RIO29_N
J24_RIO30_N
J24_RIO31_N
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
PCIe x16 @ x4 Connector – J4
Pin Number
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
Description
GND
+12V
+12V
GND
NC
NC
NC
NC
+3.3V
+3.3V
PLT_RST#
GND
CLK_PEG_P
CLK_PEG_N
GND
PCIE0_RX_P
PCIE0_RX_N
GND
NC
GND
PCIE1_RX_P
PCIE1_RX_N
GND
GND
PCIE2_RX_P
PCIE2_RX_N
GND
GND
PCIE3_RX_P
PCIE3_RX_N
Pin Number
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
Description
+12V
+12V
+12V
GND
NC
NC
GND
+3.3V
NC
+3.3V
WAKE#
NC
GND
PCIE0_TX_P
PCIE0_TX_N
GND
NC
GND
PCIE1_TX_P
PCIE1_TX_N
GND
GND
PCIE2_TX_P
PCIE2_TX_N
GND
GND
PCIE3_TX_P
PCIE3_TX_N
GND
NC
Note: Only top 4 lanes are connected. All other pin’s A31-A32 & B30-B82 are NC with the exception of
grounds.
Acromag, Inc. Tel: 248-295-0310
- 40 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
Dual USB 2.0 Port 1 & 2 Connector – J9
Pin Number
1
2
3
4
5
6
7
8
Description
USB4_+5V
USB4_N
USB4_P
GND
USB5_+5V
USB5_N
USB5_P
GND
Dual USB 3.0 Port 1 & 2 Connector – J11 (See note, page 53)
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Acromag, Inc. Tel: 248-295-0310
- 41 -
Description
USB0_+5V
USB0_N
USB0_P
GND
USB0_SSRX_N
USB0_SSRX_P
GND
USB0_SSTX_N
USB0_SSTX_P
USB1_+5V
USB1_N
USB1_P
GND
USB1_SSRX_N
USB1_SSRX_P
GND
USB1_SSTX_N
USB1_SSTX_P
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
Dual USB 3.0 Port 3 & 4 Connector – J10 (See note, page 53)
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Description
USB2_+5V
USB2_N
USB2_P
GND
USB2_SSRX_N
USB2_SSRX_P
GND
USB2_SSTX_N
USB2_SSTX_P
USB3_+5V
USB3_N
USB3_P
GND
USB3_SSRX_N
USB3_SSRX_P
GND
USB3_SSTX_N
USB3_SSTX_P
SATA 0 Connector – J5
Signal
Pin Number
1
2
3
4
5
6
7
Acromag, Inc. Tel: 248-295-0310
Power
Pin Number
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Description
GND
SATA0_TX+
SATA0_TXGND
SATA0_RXSATA0_RX+
GND
- 42 -
Description
+3.3V
+3.3V
+3.3V
GND
GND
GND
+5V
+5V
+5V
GND
NC
GND
+12V
+12V
+12V
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
SATA 1 Connector – J8
Signal
Pin Number
1
2
3
4
5
6
7
Power
Pin Number
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Description
GND
SATA1_TX+
SATA1_TXGND
SATA1_RXSATA1_RX+
GND
Description
+3.3V
+3.3V
+3.3V
GND
GND
GND
+5V
+5V
+5V
GND
NC
GND
+12V
+12V
+12V
LAN 1 Connector – J12
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Acromag, Inc. Tel: 248-295-0310
- 43 -
Description
GND
LAN_MDI2_N
LAN_MDI2_P
LAN_MDI1_P
LAN_MDI1_N
GND
GND
LAN_MDI3_P
LAN_MDI3_N
LAN_MDI0_N
LAN_MDI0_P
GND
LAN_LINK#
+3.3V
+3.3V
LAN_ACT#
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
LAN 2 Connector – J13
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Description
GND
LAN1_MDI2_N
LAN1_MDI2_P
LAN1_MDI1_P
LAN1_MDI1_N
GND
GND
LAN1_MDI3_P
LAN1_MDI3_N
LAN1_MDI0_N
LAN1_MDI0_P
GND
LAN1_LINK#
+3.3V
+3.3V
LAN1_ACT#
Dual Audio (Line In/ Line Out) Connector – J15
Pin Number
5U
1U
4U
5L
1L
4L
Description
AUDIO_GND
LINE_IN_R
LINE_IN_L
AUDIO_GND
LINE_OUT_L
LINE_OUT_R
Pin Number
1
2
3
4
5
6
7
8
Description
GPI_0
GPO_0
GPI_1
GPO_1
GPI_2
GPO_2
GPI_3
GPO_3
Line IN = TOP
Line OUT = Bottom
GPIO Header – P15
Acromag, Inc. Tel: 248-295-0310
- 44 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
LPC Bus Header – P16
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Description
LPC_CLK
GND
LPC_FRAME#
NC
PLT_RST#
+5V
LPC_AD3
LPC_AD2
+3.3V
LPC_AD1
LPC_AD0
GND
Reserved
Reserved
+3.3V
LPC_SERIRQ
GND
NC
SUS_STAT
DRQ Jumper
Pin Number
1
2
3
4
5
6
7
8
Description
EDP_VDDEN
THRMTRIP3#
EDP_BKLTCTL
COM_THRM#
EDP_BKLTEN
WDT0
Reserved
BATLOW#
Pin Number
1
2
3
4
5
6
7
8
Description
SLP_S5#
WAKE1#
SLP_S4#
EXCD0_PERST#
SLP_S3#
EXCD0_CPPE#
NC
SPKR
Miscellaneous I/O Header 1 – P14
Miscellaneous I/O Header 2 – P13
Acromag, Inc. Tel: 248-295-0310
- 45 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
Fan Power – P2
Pin Number
1
2
3
Description
GND
+12V
NC
Pin Number
1
2
3
Description
GND
+12V
NC
Fan Power – P3
Acromag, Inc. Tel: 248-295-0310
- 46 -
www.acromag.com
ACEX-4600-EDK User’s Manual
7.0
COM Express System Development Kit
Jumpers / Switch Settings
The following describes the ACEX-4600-EDK jumpers and switches with their default positions
and functions.
JP1
(LPC Bus IRQ
Configuration)
1-2
(default)
(LPC_DRQ1) Configured to use DRQ1
2-3
(LPC_DRQ0) Configured to use DRQ0
SW3-1
SW3
(Display Output and
ORB_GND
configuration)
SW3-2
SW3-3
SW3-4
ON
OFF
ON
OFF
ON
OFF
ON
OFF
DisplayPort 1 Active
HDMI 1 Active
DisplayPort 2 Active
HDMI 2 Active
DisplayPort 3 Active
HDMI 3 Active
ORB_GND is connected to Digital GND
ORB_GND is isolated from Digital GND
SW3
JP1
Acromag, Inc. Tel: 248-295-0310
- 47 -
www.acromag.com
ACEX-4600-EDK User’s Manual
8.0
COM Express System Development Kit
Handling
Modules should be handled in ESD-safe work areas in order to
prevent damage to sensitive components from electrostatic
discharges. These areas must be designed and maintained to prevent
ESD damage.
ESD Safe Work Area Guidelines
1. Module should be handled at properly designated work areas
only.
2. Designated ESD safe work areas must be checked periodically to
ensure their continued safety from ESD. The areas should be
monitored for the following:
a. Proper grounding methods.
b. Static dissipation of work surfaces.
c. Static dissipation of floor surfaces.
d. Operation of ion blowers and ion air guns.
3. Designated work areas must be kept free of static generating
materials such as Styrofoam, vinyl, plastic, fabrics or any other
static generating materials.
4. Work areas must be kept clean and neat in order to prevent
contamination of the work area.
5. Modules should be handled by the edges. Avoid touching the
component leads.
NOTE: When not installed in a system, modules must be enclosed
in shielded bags or boxes. There are three types of ESD protective
enclosure materials this module was shipped in an approved ESD
bag.
6. Whenever handling the module the operator must be properly
grounded by one of the following:
a. Wearing a wrist strap connected to earth ground.
b. Wearing heel grounders and have both feet on a static
dissipative floor surface.
7. Stacking of modules should be avoided to prevent physical
damage.
Acromag, Inc. Tel: 248-295-0310
- 48 -
www.acromag.com
ACEX-4600-EDK User’s Manual
9.0
COM Express System Development Kit
Service and Repair
Service and Repair Assistance
Surface-Mounted Technology (SMT) boards are generally difficult to
repair. It is highly recommended that a non-functioning board be
returned to Acromag for repair. The board can be damaged unless
special SMT repair and service tools are used. Further, Acromag has
automated test equipment that thoroughly checks the performance
of each board.
Please refer to Acromag's Service Policy Bulletin or contact Acromag
for complete details on how to obtain parts and repair.
Preliminary Service Procedure
Before beginning repair, be sure that all of the procedures in section
Error! Reference source not found.Error! Reference source not
und. have been followed. Also, refer to the documentation of your
carrier board to verify that it is correctly configured. Verify that there
are no blown fuses. Replacement of the carrier and/or IP with one
that is known to work correctly is a good technique to isolate a faulty
board.
CAUTION: POWER MUST BE TURNED OFF BEFORE REMOVING OR INSERTING BOARDS
Where to Get Help
If you continue to have problems, your next step should be to visit the
Acromag worldwide web site at http://www.acromag.com. Our web
site contains the most up-to-date product and software information.
Go to the “Support” tab to access:

Application Notes

Frequently Asked Questions (FAQ’s)

Product Knowledge Base

Tutorials

Software Updates/Drivers
An email question can also be submitted from within the Knowledge
Base or directly from the “Contact Us” tab.
Acromag’s application engineers can also be contacted directly for
technical assistance via telephone or FAX through the numbers listed
below. When needed, complete repair services are also available.
Acromag, Inc. Tel: 248-295-0310
- 49 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
Phone: 248-295-0310
Fax: 248-624-9234
Email: [email protected]
10.0 Specifications
Physical
Height
Width
Board Thickness
68.58 mm (2.700 in)
125 mm (4.921 in)
2.36 mm (0.093 in)
Unit Weight:
6.20oz (0.1757Kg)
Power Requirements
Note: The maximum current
supplied to the Carrier/Module
cannot exceed 15 Amps.
Minimum Input Voltage +10V DC
Maximum Input Voltage +36V DC
Environmental
Operating Temperature
Model
Operating Temperature
ACEX-4600-EDK
ACEX-4600-DLS
-40C to 85C
Relative Humidity: 5-95% Non-Condensing.
Storage Temperature: -55C to 100C.
Acromag, Inc. Tel: 248-295-0310
- 50 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
Revision History
The following table shows the revision history for this document:
Release Date
Version
EGR/DOC
3-JAN-14
A
MDW
Initial Acromag release.
18-Jun-14
B
PDG
Added note for USB 3.0
Acromag, Inc. Tel: 248-295-0310
Description of Revision
- 51 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
Appendix
Drive Compatibility
The ACEX-4600-EDK supports all 2.5” SATA Drives which include SAS,
Solid state Drive and rotating media type Drives. The ACEX-4600-EDK
also supports Serial ATA II features, including 3.0 Gbps SATA II
transfer speeds.
2.5” SATA HDD Mechanical
Acromag, Inc. Tel: 248-295-0310
- 52 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
USB 3.0 Data Rate
Signal conditioning is required to achieve the best data rate. The USB 3.0 signal trace lengths on the EDK
are longer than USB 3.0 specification allows for optimal data rate. For best performance use a USB 3.0
Hub with re-drivers.
Acromag, Inc. Tel: 248-295-0310
- 53 -
www.acromag.com
ACEX-4600-EDK User’s Manual
COM Express System Development Kit
Certificate of Volatility
Certificate of Volatility
Acromag Model
ACEX-4600-EDK
ACEX-4600-DLS
Manufacturer:
Acromag, Inc.
30765 Wixom Rd
Wixom, MI 48393
Volatile Memory
Does this product contain Volatile memory (i.e. Memory of whose contents are lost when power is removed)
□ Yes
■ No
Type (SRAM, SDRAM, etc.)
User Modifiable
Function:
Process to Sanitize:
Size:
□ Yes
□ No
Type (SRAM, SDRAM, etc.)
Size:
User Modifiable
Function:
Process to Sanitize:
□ Yes
□ No
Non-Volatile Memory
Does this product contain Non-Volatile memory (i.e. Memory of whose contents is retained when power is removed)
□ Yes
■ No
Type (EEPROM, Flash, etc.) Size:
User Modifiable
Function:
Process to Sanitize:
□ Yes
□ No
Type (EEPROM, Flash, etc.) Size:
User Modifiable
Function:
Process to Sanitize:
□ Yes
□ No
Type (EEPROM, Flash, etc.) Size:
User Modifiable
Function:
Process to Sanitize:
□ Yes
□ No
Other capabilities:
Does device contain media storage capabilities: □ Yes ■ No
If yes explain
Is this device capable of wireless transmission: □ Yes ■ No
If yes explain
Acromag Representative
Name:
Joseph Primeau
Title:
Dir. of Sales and Marketing
Acromag, Inc. Tel: 248-295-0310
Email:
[email protected]
- 54 -
Office Phone:
248-624-1541
Office Fax:
248-624-9234
www.acromag.com