Download DFX256 Digital Effects Processor CONTENTS
Transcript
DFX256 Digital Effects Processor DFX256 ENGLISH User’s Manual IMPORTANT SAFETY INSTRUCTIONS The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable. Warning: the user shall not place this apparatus in the confined area during the operation so that the mains switch can be easily accessible. 1. Read these instructions before operating this apparatus. 2. Keep these instructions for future reference. 3. Heed all warnings to ensure safe operation. 4. Follow all instructions provided in this document. 5. Do not use this apparatus near water or in locations where condensation may occur. 6. Clean only with dry cloth. Do not use aerosol or liquid cleaners. Unplug this apparatus before cleaning. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plug, convenience receptacles, and the point where they exit from the apparatus. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tipover. 13. Unplug this apparatus during lighting storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. DFX256 DFX256 Digital Effects Processor CONTENTS INTRODUCTION......................................................................................................................... 4 FEATURES.................................................................................................................................. 4 GETTING STARTED................................................................................................................... 4 CHANNEL SETUP.......................................................................................................................5 FRONT-PANEL DESCRIPTION...................................................................................................6 REAR-PANEL DESCRIPTION.....................................................................................................6 PRESET PROGRAMS.................................................................................................................7 SAMPLE CONNECTIONS........................................................................................................ 15 SPECIFICATIONS..................................................................................................................... 16 Phonic reserves the right to improve or alter any information suppied within this document without prior notice. V1.1 JUN 23, 2006 DFX256 INTRODUCTION GETTING STARTED Congratulations on your purchase of the Phonic DFX256 digital reverberator. The DFX256 is a high quality and easy-to-use stereo digital reverberator. To take full ad-vantage of the DFX256’s functions, and enjoy a longand trouble-free use, please read thisuser’s manualcarefully and keep it for future reference. 1. Check the AC voltage before connecting the plug. Choose the main supply for the sound system with care. Do not share sockets or earthing with light dimmers. 2. Run audio cables separately from dimmer wiring, using balanced lines wherever possible. If o necessary, cross audio and lighting cables at 90 right angles to minimize the possibility of interference. Keep unbalanced cabling as short as possible. 3. Check your cables regularly and label each end for easy identification. 4. Before switching on the main power, keep all output rotary faders all the way down to prevent damage or excessive noise caused by bad level adjustment, wrong wiring, defective cables, or bad connections. 5. Always turn on the DFX256 PRO before the power amplifier; turn off the DFX256 after turning off the amplifier. 6. Always turn off the unit before connecting or disconnecting the unit to the power source. 7. Never use any solvents to clean the unit. Clean it with a soft, dry cloth. FEATURES ● 256 effect programs available ● Programs include reverb, delay, flanger, chorus, tap delay, tremolo, phaser, pan effects and com● ● ● ● ● ● ● ● binations 32-40 bit digital signal processing plus 24 bit AD/ DA conversions True stereo reverb Easy-to-read 3-digit LED display Compact “1U” rack mount dimensions Foot SW Jacks allow the user of a footswitch to mute the effect Auto-bypass when power is off. Signal and clip LEDs easy setup of the optimum input level A professional quality digital reverb designed for musical instruments,recording, and sound reinforcement DFX256 FRONT-PANEL DESCRIPTION 6. OUTPUT LEVEL CONTROL This rotary control sets the level going to the amplifier or mixer from the output of the DFX256. 1. INPUT LEVEL CONTROL The input level control sets the level going into the DFX256. You should set the level so that Peak indicators only flash RED occasionally. 7. POWER SWITCH This switch turns the power of the DFX256 on/off. When the power is off, the DFX256 will be in signal bypass position automatically i.e. this feature allows the direct signal to pass through the DFX256 even when the power is not switched on. 2. MIX (DRY / WET) CONTROL This control sets the balance between the unaffected signal coming through the inputs and the effects being generated by the DFX256 i.e. the balance of wet (effect) and dry (no effect) sounds. By keeping the Mix somewhere in the center, a blend of dry and wet signal can be achieved. 8. SIGNAL INDICATORS These 2 small LED indicators, located within the digital effect display, show when either the left or right inputs are receiving a signal (the left LED indicates when the left input is receiving a signal, the right indicates when the right receives a signal). When the LCD display (above these indicators) flashes “C”, the signal in the left or right channel is excessive (ie. clip), and should be reduced to keep the audio’s integrity. 3. EFFECT MODES CHART This chart shows you what 256 effect modes are in the DFX256. 4. LED DISPLAY This 7-segment display indicates the current effect program in Program mode. When the display shows the letter “C” flashing, this means either the right or left input signals are too high and should be reduced. 9. LOAD INDICATOR This small LED indicator, located within the digital effect display, will flash when users are previewing different effects (when turning the program select knob). When a new program is loaded, this LED will stop flashing. 5. PROGRAM SELECT KNOB Turning this control will allow users to ‘preview’ the different digital effects. Pushing it in will load the preset. If this control is not pushed within a few seconds of changing the effect, the DFX256 will automatically revert back to the previously loaded effect. When this control is held down for a few seconds, the digital effects b will be bypassed. Holding it down again will reactivate the effects. When selecting the Tap Delay effect (T1 - T6), pushing the Program Select control will allow users to adjust the delay time. The time between the final two presses will be calculated and used as the delay time. 2 4 DFX256 5 6 7 9 REAR-PANEL DESCRIPTION 10. AC 10V IN INLET The supplied AC Adapter is plugged into this connector. 11. FOOTSWITCH This is a 1/4” stereo phone jack. If a foot switch is connected to this jack, you can use your foot to switch the effect mute on/off (bypass). 12. OUTPUT (LEFT & RIGHT) There are 1/4” phone jacks which connect to devices such as the effects returns on a mixing console or power amplifier inputs. 13. INPUT (LEFT/MONO & RIGHT) There are 1/4” phone jacks which connect to sources such as the effects sends of mixing consoles. For mono application, use the “Left/Mono” input. 2 0 DFX256 PRESET PROGRAMS PRESET PROGRAMS EFFECT 1: ROOM 7 Segment LED Room 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ROOM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 REV-T I M E P RED EL AY H I - RAT I O 0. 05 40 0. 5 0. 05 0 0. 6 0. 4 0 0. 95 0. 4 0 0. 93 0. 45 5 0. 95 0. 45 30 0. 9 0.6 0 0. 9 0.6 6 0. 92 0. 65 22 1 0. 9 6 0. 96 1 1 10 1. 2 15 0. 98 1. 4 0. 98 60 0 1. 4 0. 96 1 1. 6 22 3. 85 0. 96 25 HPF 80 0 382 430 500 0 550 0 0 0 500 410 0 22 0 0 L PF 2. 5K 1. 8K 9K 1. 25K 12. 5K 6.3K 2.36K 5.6K 19 K 8K 20 K 9. 5K 5. 6K 6. 7K 10. 6K 4.75K D RY/ W ET 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 REV -T I M E PRED ELA Y H I - RAT I O 0. 9 0 0. 9 20 0. 95 1 1. 9 5 40 0. 98 1. 7 5 48 0. 98 1. 8 20 0. 83 1. 8 5 40 0. 95 1. 9 30 0. 98 2. 2 25 0. 99 100 0. 7 2. 3 2 .4 5 30 0. 95 2 .5 0. 8 40 2. 5 0 4 2. 7 1 85 2. 7 0. 85 20 2. 8 0. 97 40 3. 3 0. 85 75 H PF 0 26 0 0 0 340 675 0 0 25 85 75 40 0 0 63 L PF 9K 10. 6K 15 k 9. 5K 4.25K 7. 1K 8. 5K 2.24K 6. 7K 8. 5K 12. 5K 3.15K 12. 5K 8K 8. 5K 10K D RY/ W ET 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 0~ 100 EFFECT 2: HALL 7 Segment LED Hall 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 DFX256 HA L L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 EFFECT 3: PLATE 7 Segment LED Plate 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 PLATE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 REV-T I M E P RED EL AY H I -RAT I O 0. 55 0 1 0. 55 0 1 0. 75 20 1 0. 9 12 0. 98 1 10 1 1. 2 25 1 35 1 1. 3 1. 8 30 0. 98 2 1 1 1 2. 25 25 2. 6 180 0. 97 2. 75 30 0. 98 3 0 1 5 0. 99 3 0. 98 3. 35 1 3.8 20 0. 85 HPF 625 625 0 0 0 20 0 80 67 42 0 0 625 0 0 0 L PF 20K 20K 12.5K 12.5K 10.6K 7.1K 20K 12.5K 20K 20K 15K 4. 25K 20K 8K 16K 1.4K D RY/ W ET 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 0~1 00 EFFECT 4: DELAY-1 (ST) 7 Segment LED Delay-1(ST) 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 DELAY-1(stereo) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 L- D EL AY 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.52 0.6 0.6 0.8 0.21 0.14 0.25 0.03 0.3 R-D EL A Y 0.03 0.08 0.08 0 0 0 0 0.2 0.2 0.2 0.3 0.2 0.05 0.05 0.06 0.06 C- D EL A Y 0.03 0.16 0 0.18 0.16 0.16 0.16 0.5 0.6 0.6 0.5 0.2 0.16 0 0.06 0 FB -D EL A Y 0. 04 0 0 0 0. 14 0. 2 0. 21 0. 3 0. 4 0. 4 0. 7 0. 1 0.16 0. 5 0. 05 0. 6 DFX256 EFFECT 5: DEALY-2 (MONO) 7 Segment LED Delay-2(MONO) 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 DEL AY-2(mono) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 L - D EL AY 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R-D ELAY 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C-D ELAY 0. 5 0. 5 0. 15 0. 15 0. 15 0. 2 0. 2 0. 4 0 0 0 0 1. 2 1. 2 0. 5 0. 15 FB - D ELAY 0. 3 0. 3 0. 1 0. 03 0. 15 0. 3 0. 2 0. 4 0. 3 0. 4 0. 4 0. 55 1 1. 2 1 0. 4 PH A SE 180 180 0 0 180 180 180 0 180 0 180 180 0 180 0 180 L PF 7.1 K 6K 8K 6. 3 K 10K 500 8K 1. 2 5K 10 K 1K 10 K 50 0 10 K 85 0 10 K 10 K EFFECT 6: CHORUS 7 Segment LED Chorus 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 DFX256 CHORUS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 L FO 0. 3 0. 8 1. 2 1. 8 2. 2 3. 6 3. 2 4 5. 6 6. 4 7. 5 7. 8 8. 4 8. 8 9. 2 10 P E R-D EL AY 2 5 20 1 60 15 30 90 120 200 88 80 50 10 5 115 EFFECT 7: FLANGER 7 Segment LED Flanger 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 FL ANGER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 LFO 0.1 0.3 0.6 0.7 1 1 1.6 1.6 2 2 2 2.6 2.8 2.8 4.6 4.6 PER-D EL AY 2 6 10 15 1 10 20 20 1 2 2 2 6 4 2 4 P H AS E 180 0 180 180 180 180 180 180 180 180 180 180 180 180 180 180 PHASER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 LFO 0. 1 0. 4 0. 8 1. 4 2. 2 2. 6 3. 3 4 4. 8 5. 2 5. 8 6 6 7. 2 7. 8 10 D EL AY 3. 5 0. 6 3. 2 0. 6 1. 6 4 1 2. 8 1 0. 1 0. 8 1. 2 3. 2 5 2. 6 5 P H AS E 180 90 180 180 180 180 180 180 180 180 180 90 180 180 180 180 EFFECT 8: PHASER 7 Segment LED Phaser 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 10 DFX256 EFFECT 9: PAN 7 Segment LED Pan 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 PAN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SPE E D 0.1 0.4 0.8 1.2 0.1 0.4 0.8 1.2 0.1 0.4 0.8 1.2 1.8 1.8 1.8 3.4 D EPT H 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 T YP E L --> R L --> R L --> R L --> R R--> L R--> L R--> L R--> L R<--> L R<--> L R<--> L R<--> L L --> R R--> L R<--> L R<--> L EFFECT 10: TREMOLO 7 Segment LED Tremolo 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 DFX256 TREMOLO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SPE E D 0. 5 0. 8 1 1. 2 1. 6 2 2. 4 3 3. 4 4 4. 4 5. 2 6 6. 6 8 10 D E PT H 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 11 EFFECT 11: DELAY + REV 7 Segment LED Delay+Rev 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 DELAY+REV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D E L AY- 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 REV ROOM 1 ROOM 7 RO O M 11 RO O M 12 RO O M 14 RO O M 15 H A LL 1 H A LL 3 H A LL 6 H A L L11 H A L L15 H A L L16 PLA T 1 PLA T 3 PLA T 6 PL A T12 CH ORU S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 REV ROOM 1 ROOM 7 RO O M 11 RO O M 12 RO O M 14 RO O M 15 H A LL 1 H A LL 3 H A LL 6 H A L L11 H A L L15 H A L L16 PLA T 1 PLA T 3 PLA T 6 PL A T12 EFFECT 12: CHORUS + REV 7 Segment LED Chorus+Rev 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 12 CHORUS+REV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DFX256 EFFECT 13: FLANGER + REV 7 Segment LED Flanger+Rev 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 FLANGER+REV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FL A N GER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 REV ROO M 1 ROO M 7 ROO M11 ROO M12 ROO M14 ROO M15 H AL L 1 H AL L 3 H AL L 6 H A L L11 H A L L15 H A L L16 PLA T 1 PLA T 3 PLA T 6 PL A T 12 PH ASER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 REV ROO M 1 ROO M 7 ROO M11 ROO M12 ROO M14 ROO M15 H AL L 1 H AL L 3 H AL L 6 H A L L11 H A L L15 H A L L16 PLA T 1 PLA T 3 PLA T 6 PL A T 12 EFFECT 14: PHASER + REV 7 Segment LED Phaser+Rev 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 DFX256 PHASER+REV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 13 EFFECT 15: TREMOLO + REV 7 Segment LED Tremolo+Rev 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 TREMOLO+REV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 REV ROOM 1 ROOM 7 ROOM11 ROOM12 ROOM14 ROOM15 H AL L 1 H AL L 3 H AL L 6 H ALL11 H ALL15 H ALL16 PLATE 1 PLATE 3 PLATE 6 PLATE 12 T REMOLO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 EFFECT 16: SPECIAL EFX 7 Segment LED Special efx 241 242 243 244 245 246 247 248 249 250 251 252 SPECI AL EFX 1 2 3 4 5 6 7 8 9 10 11 12 DELAY-1-1 FLAN GE- 3 DELAY-1-1 CHORUS- 4 D EL A Y- 1- 1 PH ASER- 7 CH ORU S- 2 FL A N G E- 1 PH ASER-10 CH ORU S- 5 TREMOLO - 6 FLANGE-11 TREMOLO-12 CH ORU S- 4 PH ASER- 5 FL AN GE- 9 PH ASER- 5 T REMOLO-12 FL A N G E- 1 TREMOLO- 6 PH A SE R- 7 PAN - 2 FLA N GE- 3 PA N - 2 EFFECT 17: GATED + REV 7 Segment LED Gated+Rev 253 254 255 256 14 GATED-REV T H RESH O LD 1 -20 2 -20 3 -20 4 -20 AT TACK 0 0 0 200 REL EASE 0.02 0.5 0.1 0.01 REV PLAT- 1 PLAT- 8 H A LL-15 H A LL-16 DFX256 SAMPLE CONNECTIONS SAMPLE CONNECTIONS ONE MONO CORD IN, ONE MONO CORD OUT (to an amplification system or mixer input) TO MIXING CONSOLE OR AMPLIFIER INSTRUMENT OF EFFECTS SEND ONE MONO CORD IN, TWO MONO CORDS OUT (to a stereo amplifier or two mixer inputs) TO MIXING CONSOLE OR AMPLIFIER INSTRUMENT OF EFFECTS SEND TWO MONO CORDS IN AND OUT (to a stereo amplifier or two mixer inputs) This can be stereo signal in/out or mono signal in/out. TO MIXING CONSOLE OR AMPLIFIER DFX256 INSTRUMENT OF EFFECTS SEND 15 SPECIFICATIONS Frequency Response Dynamic Range AD/DA DSP processing Sampling rate Maximum Input Level Residual Noise T.H.D. Input Number of Channel: Nominal Level: Impedance: 20Hz ~ 20kHz 90dB 24-bit 32~40-bit 44.1kHz 0dB < -80dB (20Hz ~ 20kHz) < .05% (typical) DFX256 2 (phone jack) -20dB 20k ohms (mono: 10k ohms) Output Number of Channel: Nominal Level: Impedance: Effect Programs 2 (phone jack) -20dB 600 ohms Front Panel Controls Real Panel Jack Dimensions (WxHxD) Net Weight Input level, Mix-dry/wet, Program select, Output level, Power Sw. 2 Input phone jacks, 2 Output phone jacks, foot Sw- phone jack, DC jack 19"x1.75"x4.2" / 483 x 44 x 107mm (1U) 2.64 lbs / 1.2 kg ROOM HALL PLATE DELAY-1(stereo) DELAY-2(mono) CHORUS FLANGER PHASER PAN TREMOLO DELAY+REV CHORUS+REV FLANGER+REV PHASER+REV TREMOLO+REV SPECIAL EFX GATED-REV TAP DELAY The specifications are subject to change without notice. 16 DFX256 6103 Johns Road #7 18 DFX256