Download SDC 15 - United Automation

Control output Just-FiTTER
ON/OFF control
Overshoot suppression coefficient 0 to 100
Operation clearance (°C)
0 to 9999 or 0.0 to 999.9
Control operation selection Direct action or reverse action
RUN/READY selection
Selected with the RDY key on the front panel or external contact input (In READY mode: Control output OFF)
Heat/Cool control selection Control output and event output
External
contact
(digital input)
Number of inputs
2 points
Function
Up to four kinds of setting value (SP) selections, RUN/READY selection, AUTO/MANUAL section, Auto tuning
stop/start, Self-turning disable/enable, Control action Direct/Reverse selection, SP ramp enable/disable, PV
value hold, Max. PV value hold, Min. PV value hold, Timer start/stop, All DO latch cancellation
Input rating
Non-voltage contact or open collector
Min. detection holding time 1s or longer
Allowable ON contact Max. 250Ω
resistance
Allowable OFF
contact resistance
Min.100kΩ
Allowable ON-state
residual voltage
Max. 1.0V
Open terminal voltage 5.5Vdc±1V
ON terminal voltage
Event
Approx. 7.5mA (at short-circuit), Approx. 5.0mA (at contact resistance of 250Ω)
Number of output points 0 to 3 points (depending on the model)
Number of internal
event settings
Up to 5 settings
Event type
PV high limit
● shows that the ON/
OFF is changed at
this value.
Direct action
HYS
shows that the ON/
OFF is changed at
a point that "1U" is
added to this value.
PV low limit
Reverse action
ON
ON
Direct action
ON
HYS
Main setting
Main setting
PV
HYS
HYS
Main setting
PV
PV high/low limit
ON
ON
HYS
Sub-setting
Main setting
Direct action
HYS
HYS
ON
ON
HYS
HYS
ON
PV
PV
ON
Direct action
ON
ON
HYS
Main setting
ON
HYS
ON
HYS
ON
Main setting
Direct action
HYS
HYS
Sub-setting
HYS
MV
HYS
Main setting
HYS
Main setting
HYS
Main setting
ON
HYS
ON
Main setting
HYS
Sub-setting
MV
Heater short-circuit
HYS
Sub-setting
CT at output ON
3
ON
MV
Reverse action
ON
Reverse action
Sub-setting
MV
Sub-setting
CT at output ON
HYS
MV
HYS
Heater burnout/Over-current
ON
Main setting
Direct action
ON
ON
Main setting
Direct action
HYS
MV high/low limit
Reverse action
HYS
ON
ON
MV
SP
Main setting
Reverse action
Main setting
MV low limit
ON
SP
MV high limit
SP
Direct action
ON
Main setting
SP
Reverse action
Sub-setting
Reverse action
HYS
SP
HYS
HYS
HYS
ON
Main setting Sub-setting
PV
SP
Main setting
SP high/low limit
Main setting
HYS
SP low limit
Reverse action
Main setting
SP
Direct action
ON
Main setting Sub-setting
PV
SP
PV
ON
Reverse action
HYS
HYS
SP high limit
HYS
SP + Main setting
Direct action
SP + Main setting
Direct action
HYS
Deviation high/low limit
Reverse action
SP + Main setting
ON
PV
PV
Deviation low limit
ON
Reverse action
SP + Main setting
Sub-setting
PV
Direct action
PV
Deviation high limit
Reverse action
HYS
HYS
Main setting
ON
Main setting
PV
Direct action
Reverse action
Direct action
HYS
ON
Main setting
CT at output OFF
Reverse action
ON
HYS
Main setting
CT at output OFF