Download PAS08FN82448 User`s Manual
Transcript
PAS08FN82448 User’s Manual HC(S)08 Programming Adapter PAS08FN82448UM Revision 0.1, June 2005 User’s Manual — PAS08FN82448 HC(S)08 Programming Adapter PAS08FN82448 Quick Start Guide The PAS08FN82448 is a low-cost universal programming adapter for HC08 and HCS08 family MCUs. It is designed to work with programmers that use a 16-pin MON08 interface for HC08 MCUs or a 6-pin BDM interface for HCS08 MCUs. It supports 8-pin DFN packages, 24-pin QFN packages and 48-pin QFN packages. 1 - Connect wire jumpers MON08 connector J2 has the same pin signals as header J3. For MON08 programming, you must connect the supplied jumpers from J3 to J11 for 8-pin DFN devices, from J3 to J12 for 24-pin QFN devices or from J3 to J10 for 48-pin QFN devices. BDM connector J7 has the same pin signals as header J9. For BDM programming, you must connect the supplied jumpers from J7 to J11 for 8-pin DFN devices, from J7 to J12 for 24-pin QFN devices or from J7 to J10 for 48-pin QFN devices. Headers J4 and J5 provide additional jumper connections to VDD and GND for both MON08 and BDM interfaces. The jumpers provide power and programming signals from the programmer to the MCU in the socket. Connections will vary depending on the specific device you are using. Refer to the device data sheet and the programmer documentation for connection information. 2 - Insert a device to be programmed Be sure that power is removed before inserting a device. Socket U1 is used for 8-pin DFN devices, socket U2 for 24-pin QFN devices or socket U3 for 48-pin QFN devices. Open the desired socket and insert the MCU. You should not use force when closing the socket lid. Close the socket latch to secure the device. PAS08FN82448 User’s Manual, Rev. 0.1 3 - Connect the MON08 or BDM programmer and program the device Connect a MON08 programmer to connector J2 of the programming adapter board or connect a BDM programmer to connector J9 of the programming adapter board. Be sure to verify that pin one of the programmer cable connects to pin one of the connector. If you are programming using BDM, you may need to supply power using connector J8. You may now use the programmer to program the inserted device. Refer to your programmer documentation for further operating instructions. Once the programmer indicates that the device has been properly programmed you may turn off power, open the socket and remove the device. PAS08FN82448 User’s Manual, Rev. 0.1 Freescale Semiconductor Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Quantity 1 3 1 1 2 2 1 1 1 1 3 1 1 1 Reference C1 JP1,JP2,JP3 J2 J3 J4,J5 J7,J9 J8 J10 J11 J12 R1,R2,R3 U1 U2 U3 Part 0.1uF HDR_1X1 TST-108-01-S-D TSW-108-07-GD HDR_3X1 TSW-103-07-S-D TB2 HDR_24X2 TSW-104-07-S-D TSW-112-07-S-D 0ohm DFNSOCKET8 QFNSOCKET24 QFNSOCKET48 Agile PN 150-75022 210-75437 210-75459 210-11112-00 210-75441 210-75698 210-75422 210-75505 210-75541 210-75091-00 470-75022 210-75695 210-75705 210-75706 Mfg_Name01 KEMET FCI SAMTEC SAMTEC FCI SAMTEC TYCO SAMTEC SAMTEC SAMTEC YAGEO AMERICA PLASTRONICS SOCKET COMPANY, INC ENPLAS ENPLAS Mfg_PN01 C410C104M5U5CA 68001-601 TST-108-01-S-D TSW-108-07-GD 68001-603 TSW-103-07-S-D 1437671-1 TSW-124-07-S-D TSW-104-07-S-D TSW-112-07-S-D ZOR-25-_ 08TN80T14040 QFN-24-0.5BT-0.5-01 QFN-48(56)BT-0.5-01 Description CAP CER 0.1UF 50V 20% Z5U TH HDR 1X1 TH 100MIL SP 330H AU HDR 2X8 TH 100MIL CTR 330H AU SHRD CONN,HEAD,2X8,STRAIGHT,OPEN HDR 1X3 TH 100MIL SP 330H AU HDR 2X3 TH 100MIL CTR 330 AU CON 2 TB FLIP TH HDR 2X24 TH 100MIL CTR 330H AU HDR 2X4 TH 100MIL CTR CONN,HEAD,2X12,.025 RES TF 0 OHM 1/4W 5% SKT CLAM DFN 8 PINS SKT CLAM QFN 24 PINS SKT CLAM QFN 48 PINS 5 4 3 2 1 VDD J4 1 2 3 VDD HDR_3X1 D D J5 U1 A1 A3 A5 A7 1 3 5 7 B1 B3 B5 B7 B9 B11 B13 B15 B17 B19 B21 B23 1 3 5 7 9 11 13 15 17 19 21 23 B2 B4 B6 B8 B10 B12 B14 B16 B18 B20 B22 B24 R2 0ohm 5% TST-108-01-S-D 25 U3 1 3 5 7 9 11 13 15 J10 IO48 IO47 IO46 IO45 IO44 IO43 IO42 IO41 IO40 IO39 IO38 IO37 IO36 IO35 IO34 IO33 IO32 IO31 IO30 IO29 IO28 IO27 IO26 IO25 IO49 IO1 IO2 IO3 IO4 IO5 IO6 IO7 IO8 IO9 IO10 IO11 IO12 IO13 IO14 IO15 IO16 IO17 IO18 IO19 IO20 IO21 IO22 IO23 IO24 C2 C4 C6 C8 C10 C12 C14 C16 C18 C20 C22 C24 C26 C28 C30 C32 C34 C36 C38 C40 C42 C44 C46 C48 C1 C3 C5 C7 C9 C11 C13 C15 C17 C19 C21 C23 C25 C27 C29 C31 C33 C35 C37 C39 C41 C43 C45 C47 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 2 4 6 8 10 12 14 16 1 3 5 2 2 4 6 1 TSW-103-07-S-D TSW-108-07-GD C2 C4 C6 C8 C10 C12 C14 C16 C18 C20 C22 C24 C26 C28 C30 C32 C34 C36 C38 C40 C42 C44 C46 C48 J8 J9 B GND A VDD C TB2 J7 1 3 5 2 4 6 TSW-103-07-S-D HDR_24X2 49 QFNSOCKET48 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 VDD J3 JP2 HDR_1X1 1 C1 0.1uF 0.2 R3 0ohm 5% R1 0ohm 5% TSW-112-07-S-D C 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2 4 6 8 10 12 14 16 18 20 22 24 VDD 1 B2 B4 B6 B8 B10 B12 B14 B16 B18 B20 B22 B24 1 24 23 22 21 20 19 18 17 16 15 14 13 2 2 4 6 8 10 12 14 16 2 IO24 IO23 IO22 IO21 IO20 IO19 IO18 IO17 IO16 IO15 IO14 IO13 IO25 IO1 IO2 IO3 IO4 IO5 IO6 IO7 IO8 IO9 IO10 IO11 IO12 1 1 3 5 7 9 11 13 15 1 J12 QFNSOCKET24 C1 C3 C5 C7 C9 C11 C13 C15 C17 C19 C21 C23 C25 C27 C29 C31 C33 C35 C37 C39 C41 C43 C45 C47 HDR_3X1 J2 JP1 HDR_1X1 U2 1 2 3 4 5 6 7 8 9 10 11 12 A2 A4 A6 A8 TSW-104-07-S-D 1 B1 B3 B5 B7 B9 B11 B13 B15 B17 B19 B21 B23 2 4 6 8 2 DFNSOCKET8 A2 A4 A6 A8 8 7 6 5 IO8 IO7 IO6 IO5 2 IO1 IO2 IO3 IO4 IO9 1 2 3 4 9 A1 A3 A5 A7 1 2 3 J11 JP3 1 HDR_1X1 B B A A Drawing Title: PAS08FN82448 Page Title: Programming Adapter 5 4 3 2 Size C Document Number Date: Friday, June 10, 2005 Rev B SCH-20870 - PDF: SPF-20870 Sheet 1 2 of 2 How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or USA/Europe/Locations not listed: Freescale Semiconductor Literature Distribution P.O. Box 5405, Denver, Colorado 80217 1-800-521-6274 or 480-768-2130 Japan: Freescale Semiconductor Japan Ltd. SPS, Technical Information Center 3-20-1, Minami-Azabu Minato-ku Tokyo 106-8573, Japan 81-3-3440-3569 Asia/Pacific: Freescale Semiconductor H.K. Ltd. 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T. Hong Kong 852-26668334 Learn More: For more information about Freescale Semiconductor products, please visit http://www.freescale.com fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2005. PAS08QF82448UM Rev. 0.1, 6/2005