Download PAS08QF80 User`s Manual
Transcript
PAS08QF80 User’s Manual HC(S)08 Programming Adapter PAS08QF80UM Revision 0.1, June 2005 User’s Manual — PAS08QF80 HC(S)08 Programming Adapter PAS08QF80 Quick Start Guide The PAS08QF80 is a low-cost universal programming adapter for HC08 and HCS08 family MCUs. It is designed to work with programmers that use a 16-pin MON08 interface for HC08 MCUs or a 6-pin BDM interface for HCS08 MCUs. It supports 80-pin 0.5mm QFP and 80-pin 0.65mm QFP packages. 1 - Connect wire jumpers MON08 connector J2 has the same pin signals as header J3. For MON08 programming, you must connect the supplied jumpers from J3 to J1 and J4. BDM connector J8 has the same pin signals as header J9. For BDM programming, you must connect the supplied jumpers from J8 to J1 and J4. Headers J5 and J6 provide additional jumper connections to VDD and GND for both MON08 and BDM interfaces. The jumpers provide power and programming signals from the programmer to the MCU in the socket. Connections will vary depending on the specific device you are using. Refer to the device data sheet and the programmer documentation for connection information. 2 - Insert a device to be programmed Be sure that power is removed before inserting a device. Socket U1 is used for 80-pin 0.5mm QFP devices and socket U2 for 80-pin 0.65mm QFP devices. Open the lever for the desired socket and insert the MCU. You should not use force when closing the socket lid. Close the socket latch to secure the device. PAS08QF80 User’s Manual, Rev. 0.1 3 - Connect the MON08 or BDM programmer and program the device Connect a MON08 programmer to connector J2 of the programming adapter board or connect a BDM programmer to connector J9 of the programming adapter board. Be sure to verify that pin one of the programmer cable connects to pin one of the connector. If you are programming using BDM, you may need to supply power using connector J7. You may now use the programmer to program the inserted device. Refer to your programmer documentation for further operating instructions. Once the programmer indicates that the device has been properly programmed you may turn off power, open the socket and remove the device. PAS08QF80 User’s Manual, Rev. 0.1 Freescale Semiconductor Item Quantity Reference 1 1 C1 2 2 J1,J4 3 1 J2 4 1 J3 5 2 J5,J6 6 1 J7 7 2 J8,J9 8 3 R1,R2,R3 9 1 U1 10 1 U2 Part 0.1uF HDR_20X2 TST-108-01-S-D TSW-108-07-GD HDR_5X1 TB2 TSW-103-07-S-D 0ohm QFPSOCKET80_0.5MM QFPSOCKET80_0.65MM Agile PN 150-75022 210-75447 210-75459 210-11112-00 210-75443 210-75422 210-75698 470-75022 210-75498 210-75499 Mfg_Name01 KEMET SAMTEC SAMTEC SAMTEC FCI TYCO SAMTEC YAGEO AMERICA ENPLAS ENPLAS Mfg_PN01 C410C104M5U5CA TSW-120-07-S-D TST-108-01-S-D TSW-108-07-GD 68001-605 1437671-1 TSW-103-07-S-D ZOR-25-_ FPQ-80-0.5-04 FPQ-80-0.65-02A Description CAP CER 0.1UF 50V 20% Z5U TH HDR 2X20 TH 100MIL CTR 330H AU HDR 2X8 TH 100MIL CTR 330H AU SHRD CONN,HEAD,2X8,STRAIGHT,OPEN HDR 1X5 TH 100MIL CTR 330H AU CON 2 TB FLIP TH HDR 2X3 TH 100MIL CTR 330 AU RES TF 0 OHM 1/4W 5% SKT 0.5MM 80 PINS QFP80_PSOC_5MM_ENP SKT 0.65MM 80 PINS QFP80_PSOC_65MM_ENP 5 4 3 2 1 U1 A2 A4 A6 A8 A10 A12 A14 A16 A18 A20 A22 A24 A26 A28 A30 A32 A34 A36 A38 A40 A42 A44 A46 A48 A50 A52 A54 A56 A58 A60 A62 A64 A66 A68 A70 A72 A74 A76 A78 A80 J1 A1 A3 A5 A7 A9 A11 A13 A15 A17 A19 A21 A23 A25 A27 A29 A31 A33 A35 A37 A39 B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 IO1 IO2 IO3 IO4 IO5 IO6 IO7 IO8 IO9 IO10 IO11 IO12 IO13 IO14 IO15 IO16 IO17 IO18 IO19 IO20 IO21 IO22 IO23 IO24 IO25 IO26 IO27 IO28 IO29 IO30 IO31 IO32 IO33 IO34 IO35 IO36 IO37 IO38 IO39 IO40 IO80 IO79 IO78 IO77 IO76 IO75 IO74 IO73 IO72 IO71 IO70 IO69 IO68 IO67 IO66 IO65 IO64 IO63 IO62 IO61 IO60 IO59 IO58 IO57 IO56 IO55 IO54 IO53 IO52 IO51 IO50 IO49 IO48 IO47 IO46 IO45 IO44 IO43 IO42 IO41 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 D A79 A77 A75 A73 A71 A69 A67 A65 A63 A61 A59 A57 A55 A53 A51 A49 A47 A45 A43 A41 VDD J5 1 2 3 4 5 VDD HDR_5X1 J6 1 2 3 4 5 J2 HDR_5X1 J4 A2 A4 A6 A8 A10 A12 A14 A16 A18 A20 A22 A24 A26 A28 A30 A32 A34 A36 A38 A40 A42 A44 A46 A48 A50 A52 A54 A56 A58 A60 A62 A64 A66 A68 A70 A72 A74 A76 A78 A80 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 A2 A4 A6 A8 A10 A12 A14 A16 A18 A20 A22 A24 A26 A28 A30 A32 A34 A36 A38 A40 1 2 R2 0ohm 5% 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 VDD 1 A80 A78 A76 A74 A72 A70 A68 A66 A64 A62 A60 A58 A56 A54 A52 A50 A48 A46 A44 A42 U2 A1 A3 A5 A7 A9 A11 A13 A15 A17 A19 A21 A23 A25 A27 A29 A31 A33 A35 A37 A39 A41 A43 A45 A47 A49 A51 A53 A55 A57 A59 A61 A63 A65 A67 A69 A71 A73 A75 A77 A79 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 HDR_20X2 QFPSOCKET80_0.5MM C 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 TST-108-01-S-D 2 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 1 IO80 IO79 IO78 IO77 IO76 IO75 IO74 IO73 IO72 IO71 IO70 IO69 IO68 IO67 IO66 IO65 IO64 IO63 IO62 IO61 IO60 IO59 IO58 IO57 IO56 IO55 IO54 IO53 IO52 IO51 IO50 IO49 IO48 IO47 IO46 IO45 IO44 IO43 IO42 IO41 C C1 0.1uF 0.2 R3 0ohm 5% R1 0ohm 5% 2 IO1 IO2 IO3 IO4 IO5 IO6 IO7 IO8 IO9 IO10 IO11 IO12 IO13 IO14 IO15 IO16 IO17 IO18 IO19 IO20 IO21 IO22 IO23 IO24 IO25 IO26 IO27 IO28 IO29 IO30 IO31 IO32 IO33 IO34 IO35 IO36 IO37 IO38 IO39 IO40 1 D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 VDD 2 A1 A3 A5 A7 A9 A11 A13 A15 A17 A19 A21 A23 A25 A27 A29 A31 A33 A35 A37 A39 A41 A43 A45 A47 A49 A51 A53 A55 A57 A59 A61 A63 A65 A67 A69 A71 A73 A75 A77 A79 J3 HDR_20X2 1 3 5 7 9 11 13 15 J7 J9 2 4 6 8 10 12 14 16 1 3 5 2 4 6 TSW-103-07-S-D TSW-108-07-GD 2 B GND 1 A VDD TB2 J8 1 3 5 2 4 6 TSW-103-07-S-D B QFPSOCKET80_0.65MM A A Drawing Title: PAS08QF80 Page Title: Programming Adapter 5 4 3 2 Size C Document Number Date: Friday, June 10, 2005 Rev B SCH-20919 - PDF: SPF-20919 Sheet 1 2 of 2 How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or USA/Europe/Locations not listed: Freescale Semiconductor Literature Distribution P.O. Box 5405, Denver, Colorado 80217 1-800-521-6274 or 480-768-2130 Japan: Freescale Semiconductor Japan Ltd. SPS, Technical Information Center 3-20-1, Minami-Azabu Minato-ku Tokyo 106-8573, Japan 81-3-3440-3569 Asia/Pacific: Freescale Semiconductor H.K. Ltd. 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T. Hong Kong 852-26668334 Learn More: For more information about Freescale Semiconductor products, please visit http://www.freescale.com fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2005. PAS08QF80UM Rev. 0.1, 6/2005