Download Manual - Global CCTV PTY LTD

1. Check Frame rate setting based on power frequency
- Set Frame rate to 25Hz if your region is using 50Hz(PAL) power frequency, or set to
30Hz for 60Hz(NTSC) region. (OSD : System  Frame rate).
2. Shutter mode setup based on installation environment
-
INDOOR : Controls brightness for the best video quality at indoor environment.
-
OUTDOOR : Controls brightness for the best video quality at outdoor environment.
-
INDOOR/OUTDOOR-ANTI BLUR : Improves the motion blurring phenomenon than
Indoor/Outdoor mode under dark environment but the brightness decreases relatively.
3. DC12V or AC24V(500mA over) power adapter must be used.
4. Please contact to qualified service personnel in case of product damage. Do not
attempt to repair product by yourself.
5. Please avoid external shock and vibration on the product.
6. Do not install product under excessive heat or cold environment. (recommended
operation temperature is 0°C~50°C)
7. Do not target lens to the sun. Image sensor might be damaged
8. Do not open the product under any circumstances, it could void the warranty. Natural
disaster like lightning, flood will need charge for repair.
1
English
Caution for installation and usage
Feature
HD-SDI video digital signal
HD-SDI(High Definition Serial Digital Interface) is non-compressed digital signal for
broadcasting, and there is no quality loss of high definition images.
2MP, Full HD high resolution picture quality
Full HD(1920x1080) provides 6 times higher resolution than SD level camera, and more
clear video image can be achieved through 1/3”, 2Megapixel progressive CMOS.
High performance under low light environment
High performance quality can be achieved under low light environment by optimizing the
image handling technology on CMOS sensor.
(B/W : 0.0005 Lux / Color : 0.2Lux@50IRE, F.1.2, 3100K, DSS OFF)
Indoor/Outdoor function
Minimizes the motion blur of object from slowly moving person(Indoor) to fast moving
vehicle(outdoor) by optimizing the signal processing and controls brightness automatically
to perform the best video image
3D-DNR
3D-DNR function efficiently removes video noise in dark environment, and shows clear
image as a result.
True Day & Night function
Camera senses the surrounding brightness automatically, and insert/remove the IR-CUT
filter to get the best sensitivity performance.
WDR/BLC/ACE/HLC
Under backlight condition, you can select the most suitable function among WDR, BLC,
ACE and HLC.
Auto Focusing function
Auto Focusing function performs Correct and Quick focusing of camera by just one click.
After the power is turned on, camera can judge reasonable brightness to execute Auto
Focusing. If the environment is bright enough, it performs Auto focusing, meanwhile it
keeps previous focus condition if the environment is dark.
Privacy support
Camera can support up to 28 privacy masking areas.
OSD control and F/W upgrade
OSD control and Firmware upgrade of camera can be achieved from PC or Webgate DVR
through RS485 communication.
2
Supplied accessories
Please check if all the supplied accessories are included.
Camera
Installation / User Manual
Monitoring Cable(IR18)
Hood Screw(IR18)
Screw & Plastic Anchor
L Wrench
Hood(IR48)
Hood(IR18)
Product description
No
Name
1
Camera
2
Camera Hood
3
RS485 Port
4
Power input connector
5
Video output BNC connector
Camera installation
Auto Iris connector wiring
1) Move joystick shortly to enter Manual Focusing mode.
2) Move joystick up(Tele) or down(Wide) to adjust the angle of view.
3) Push the center of joystick shortly to exit Manual Focusing mode then push again
shortly one more time to activate Auto Focusing function for exact focus.
3
<Note>
1) To adjust exact focus, the image will enlarge 2 times bigger under Auto Focusing mode.
2) In case of AF models, Zoom Tracking function will work together with zoom control under
Manual Focusing mode. But this function will work normally when the focus is adjusted
well before zoom control.
Notice for Auto Focus operation
Following conditions might make failure of auto focusing .
1. When there are changes of the scene while Auto Focus is working(sudden movement,
appearance or disappearance).
2. When there are sudden change of the brightness.
3. When shooting low contrast image.
4. When there is strong light in the scene.
5. When there is foreign substance on the lens.
6. If auto focusing is failed, please try to adjust focus manually or try auto focus again
with the scene which have strong contrast.
Monitor connection
1. Use coaxial cable to connect camera with monitor.
2. Monitor needs to support SDI.
3. If monitor does not have SDI input connector, you may use additional SDI to HDMI
converter.
Cautions when you connect BNC cable
The impedance of BNC connector should be 75Ω.
If 50Ω connector is used, the transmission distance will be reduced approx. 10m.
Caution in cable selection
The maximum transmission distance of HD-SDI will vary depending on cable manufacturer
and installation environment. Please refer to the below table to select suitable coaxial cable.
Cable type
Transmission distance
Purpose
2V
about 100M
For analog signal
4C-FB(T), 4C-HFB(T), RG59
about 150M
High-foamed, double or triple
shielded cable is recommended
5C-FB(T), 5C-HFB(T), L-6CHD,
RG6
about 200M
Dedicated cable for HD-SDI
4
Power connection
Adapter should be DC12V or AC24V. But in case use DC power,
Please be careful in the polarity when connect power.
OSD control and Firmware upgrade using RS485 communication
1. Connect Webgate’s HD-SDI DVR with camera through RS485.
2. Configure PTZ settings such as Protocol(C1080), Baudrate, Address in DVR.
3. Run HD Camera Upgrade program then enter IP address of DVR which is connected to
camera and enter channel number of camera.
- PC for Firmware upgrade and DVR need to be connected with network.
- HD Camera Upgrade program and firmware can be downloaded from Webgate’s
website.
4. Select a Firmware and click Load button. Then firmware upgrade will proceed and the
camera will reboot automatically after completion.
- Image will stop until boot completes.
- If image stops over 1min, select Aux1 of selected channel to reboot camera again.
5. After firmware upgrade, DVR or CMS(Control Center) can change camera configuration
by controlling camera’s OSD menu remotely.
<Note>
1) All setting values will be initialized in case of F/W upgrade.
How to use OSD menu
OSD menu function
If pressing MENU button over 1 sec continuously, OSD menu will be shown.
- If OSD menu is not closed, it will be closed automatically in 1 minute. (Changed
configuration value will not be saved)
- Bold font with underline means factory default.
5
OSD MENU
MANUAL
FOCUSING
Function
Move joystick shortly to activate Manual Focusing mode
- Zoom Tracking function will be activated when control Zoom. But this
function will work normally when the focus is adjusted well before
zoom control.
- If you do not exit the menu, it will be closed automatically in 2 second.
LENS
DC
This menu is activated only in AF models. Focus can be
adjusted by automatically or manually
- PWR-ON AF : After power is turned on, camera
judges the ambient brightness. If the brightness is
enough, it performs Auto Focusing automatically, but
if the brightness is not enough, it keeps the previous
focus condition.
- Correct AF : Camera performs focusing over the fullrange (it takes max. 40seconds)
- Quick AF : If the angle of view and focus is roughly
adjusted condition, Quick AF performs fast focusing.
But, if the focus is vague condition, Quick AF may
not show good result. (it takes max. 10seconds)
- Manual : Move joystick to up(Tele), down(Wide),
left(Near),right(Far) to adjust angle and
focus manually.
DAY
&
Color
Maintains Color(Day) mode regardless brightness.
B&W
Maintains B&W(Night) mode regardless brightness.
NIGHT
Auto
In accordance with brightness, camera switches Color
mode and B&W mode automatically.
- LUX LEVEL(LOW, MIDDLE, HIGH) : This value is the
standard for Day & Night switching. If high is
selected, camera will turn to Night(B/W) mode at
higher LUX level than MIDDLE or LOW.
- ANTI HUNT(LOW, MIDDLE, HIGH) : This value is the
standard for threshold of Day & Night switching.
Higher setting value will reduce the flickering by
IR-CUT filter switching caused from misjudgment.
- DELAY TIME(3~30sec) : Judgment period for Day &
Night switching
EXPOSURE
BRIGHTNESS
(8, 0~20)
Adjust the brightness of image.
The more High value it has, the more bright image it
shows
SHUTTER
- Indoor : controls brightness to show the best video
quality at indoor environment.
- Outdoor : controls brightness to show the best video
6
-
quality at outdoor environment.
Indoor-Anti Blur : It shows better anti-blur
performance at dark indoor environment, but the
brightness level decrease a little.
Outdoor-Anti Blur : It shows better anti-blur
performance at dark outdoor environment, but the
brightness level decrease a little.
- Manual : It fixes shutter speed within 1/30 ~ 1/60000.
-
COLOR
ANTI-FLICKER
Removes Flicker problem due to the discordance of
light frequency.
DSS
(OFF, x2~x10)
At night time or very dark condition, it accumulates
the amount of light into the image pixels and provides
more clear video image. But the higher setting value
may make more severe motion blur accordingly.
AGC
(7, 1~10)
It will amplify video gain according to the light
condition, but it will also increase noise level.
AWB
- AUTO : This mode automatically adjusts color white
balance between 1,700°K ~ 11,000°K.
- PRESET : Shoot a white paper in front of camera and
press MENU button then white balance working will
stop suitable for the condition. You must do this
process again if light condition is changed.
- MANUAL : User can select color temperature among
3300°K, 4300°K, 7600°K and adjust the details by
CHROMA
(10, 0~20)
Adjust Chroma level.
SHARPNESS
(5, 0~10)
Adjust sharpness. The higher value will show more
clear video image
H-MIRROR
Mirror image. Left and right will be reversed
V-MIRROR
Flip image. Up and down will be reversed.
Digital ZOOM
Zoom image by 16 steps. (1~16)
PRIVACY
This is for privacy zone masking
KELVIN, R-GAIN and B-GAIN value.
IMAGE
- ZONE NO : Supports total 28 areas (0~27)
-
ZONE OP : Whether to use or not of selected area
X, Y-POS : Set the X,Y start position of an area
X, Y-SIZE : Set the width and height of an area
COLOR(WHT,YEL,CYN,GRN,MAG,RED,BLU,BLK) : Select
color for masking.
- TRANS(0~4) : Set transparency of masking.
SHADING
Before execute the SHADING function, shoot a white
7
DET
paper in front of the camera, and do SHADING DET. If
not, abnormal video might be output.
SHADING
It compensates the difference of light caused by lens.
To use this function, you should run Shading DET
function first at System menu.
WDR
BLC
This 3D backlight compensation function allows bright and dark area to
be seen clearly together.
- WDR WGT(0~4) : Select image mix ratio. The higher value, the bright
part of the image appear more clearly
Back light compensation function.
- BLC LEVEL(LOW, MIDDLE, HIGH) : Set BLC level.
- BLC OSD : Displays BLC area on the screen.
- BLC POS-X, Y : Set X, Y start position.
- BLC SIZ-X,Y : Set Width and Height size.
- MASK : If there is very bright portion inside BLC area, this portion can
be removed from the calculation of BLC compensation. This brightness
level for masking can be decided by below MASK LEVEL.
- MASK LEVEL(0~10) : Set brightness level for Masking.
HLC
High Light Compensation. If there is very bright portion inside a scene,
camera can mask the portion, and the portion is removed from the
calculation for exposure control.
- LEVEL(5, 0~10) : Set the brightness level for masking.
- Color : Set masking color
ACE
Adaptive Contrast Enhancement. Enhances image quality by raising the
(ON, OFF)
brightness of dark areas.
DNR
(LOW, MIDDLE, HIGH)
FRAMERATE
(25Hz, 30Hz)
SYSTEM
Reduce image noise under low light condition
Power frequency 60Hz(NTSC) : 30Hz(fps) video output
Power frequency 50Hz(PAL) : 25Hz(fps) video output
MODEL
Displays model name
CAM ID
Max. 8 digits for camera name.
Supports alphanumeric and some special characters
RS485 ID
Set ID for RS485
VERSION
Displays firmware version
VIDEO
Full-Scale(BT 709), Comp-Scale(BT 601) support
RESOLUTION
Set output resolution (1080p/720p).
DIGITAL OUT
/
IR-LED
Provides control signal output for sub light which is
synchronized with image process.
-
Smart IR : When IR-LED is activated at darkness
condition, the intensity of IR-LED is automatically
8
controlled according to the distance with target
object (Activated only at IR models)
- DURATION(0~20) : Set the one cycle duration of TTL
signal output (unit : msec)
- POLARITY : Set the output level of TTL signal.
(0 : 0V , 1 : 3.3V)
* Output cycle is decided by 30Hz/25Hz.
EXIT
BAUDRATE
(9600, 57600)
Set RS485 communication speed.
RESET
Makes all setting values to factory default condition
SAVE&EXIT
Save configuration and exit menu.
EXIT
Without saving configuration, exit menu.
If there is no further action in menu, after 1 minute,
OSD menu will exit without saving changes.
Product Specification
Model
C1080BL-IR48-AF / C1080BL-IR18-AF
Video
Sensor Type
1/3” 2.1Megapixel CMOS
Total Pixels
1920(H) x 1080(V) = 2.1M pixels
Scanning System
Progressive Scan
Min
B/W
0.0005Lux@50IRE, F1.2, 3100K, DSS(OFF), AGC(10)
Illumination
Color
0.2Lux@50IRE, F1.2, 3100K, DSS(OFF), AGC(10)
Lens
DC iris, 2.8mm~10mm, F1.2, IR Corrective Mega
Pixel Lens
type
DC Auto Iris
Output
1(BNC 1.0 Vp-p, 75Ω)
Resolution
1080p 30fps / 25fps
HD-SDI
SMPTE 292M compatible
Distance
approx. 200m of RG6, 150m of RG59
Control Method
OSD(Internal Joystic), DVR, CMS(Control Center)
Filter
True Day & Night
AGC
1 ~ 10 steps
Mirror
Horizontal / Vertical
WDR
OFF, 0 ~ 4 setup
BLC
OFF, LOW, MIDDLE, HIGH
ACE
OFF, ON
DNR
OFF, LOW, MIDDLE, HIGH
DSS
OFF, x2 ~ x10
Lens
Video Output
Video
Control
9
White Balance
AUTO, PRESET, MANUAL
Electric Shutter
INDOOR, OUTDOOR, INDOOR-ANTI BLUR,
OUTDOOR-ANTI BLUR, MANUAL(12 steps),
ANTI-FLICKER ANTI-FLICKER
Digital Zoom
0 ~ 16 steps
Lens Shading
OFF, ON
HLC
0 ~ 10 steps
Privacy
OFF/ON (28 Zones )
Smart IR
OFF/ON
Control Interface
RS485
Upgrade Firmware / OSD Control
Strobe for external light
TTL level(3.3v)
Electricity
Power
Consumption
C1080BL-IR18-AF
DC 12V ± 10%, 4W / AC 24V ± 10%, 6W
C1080BL-IR48-AF
DC 12V ± 10%, 5W / AC 24V ± 10%, 8W
C1080BL-IR18-AF
88(W) x 118(H) x 198(D) mm
C1080BL-IR48-AF
120(W) x 140(H) x 254(D) mm
C1080BL-IR18-AF
720g
C1080BL-IR48-AF
1600g
Mechanical
Dimension
Weight
Environments
Operation Temp. / Humidity
0 ºC ~ 50 ºC / 0%RH ~ 80%RH
Certifications
Certifications
KC, FCC, CE, RoHS
10
Dimension
(unit : mm)
C1080BL-IR18-AF
C1080BL-IR-48-AF
11
Warranty
Product name
HD-SDI Camera
Model name
Warranty term
C1080BL-IR48-AF, 1080BL-IR18-AF
Date of purchase
20
-
-
2 years after
Warranty term
20
-
-
purchase
Serial number
Name
Customer’s address
Contact
Name
Address of shop(Company name)
Contact
◈ Please fill out vacant area before sending products.
★ For customer service ★
Please read this manual again before requesting customer service.
Any simple malfunctions due to customer’s misunderstanding on the product could be
resolved by customer.
How to request service?
Please inform details of malfunctions correctly.
Free or non free repair will be decided based on details of warranty card.
WebGate Division Daemyung Enterprise Co., Ltd.
6F Hanlim Venture Town B/D 689-6, Geumjeong Dong, Gunposi, Gyeonggido,Korea
Main
: TEL : +82-31-428-9300
Client Service : TEL : +82-1644-3421
The damages caused from following conditions will be repaired by customer’s cost.
1. Any damage comes from customer’s carelessness
2. When improper power is entered
3. When you repair unit by yourself
4. Any damage comes from natural disaster like lightning, flood, etc.
5. Consumable parts replacement
12
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense. Modifications not expressly
approved by the manufacturer could void the user’s authority to operated
the equipment under FCC rules.
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking on the product, accessories or literature indicates that the
product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end
of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote
the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased
this product or their local government office, for details of where and how
they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for
disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with
separate battery return systems.)
This marking on the battery, manual or packaging indicates that the
batteries in this product should not be disposed of with other household
waste at the end of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains mercury,
cadmium or lead above the reference levels in EC Directive 2006/66. If
batteries are not properly disposed of, these substances can cause harm
to human health or the environment.
To protect natural resources and to promote material reuse, please
separate batteries from other types of waste and recycle them through
your local, free battery return system.
13
Global CCTV
AUSTRALIA
Tel : +61 8 9
!" : #$%""&'com.au
Webite: www.GlobalCCTV. Mail: Info@GlobalCCTV.
14