Download View the Installation Instructions

INSTALLATION
INSTRUCTIONS
Accessory
Application
FRONT GRILLE
P/N 08F21-T5A-300
2015 FIT
Publications No.
AII 51170
PARTS LIST
Issue Date
APR 2014
INSTALLATION
Front grille
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
TOOL AND SUPPLIES REQUIRED
1.
Disconnect the negative cable from the battery.
2.
Remove the front bumper:
Phillips screwdriver
Ratchet
•
10 mm Socket
Attach tape to the areas shown.
Tape
Blanket
The following tool is available through the Honda Tool and
Equipment Program. On the iN, click on: Service >
Service Bay > Tool and Equipment Program, then enter
the number under “Search”. Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
FRONT
FENDER
TAPE
FRONT BUMPER
QC71101AH
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
AII 51170 (1404)
08F21-T5A-1000-90
1 of 5
•
Remove the grille cover.
•
3 CLIPS
GRILLE COVER
•
Remove six self-tapping screws and eight clips.
2 SELFTAPPING
SCREWS
FRONT BUMPER
2 SELFTAPPING
SCREWS
(flat head)
QC71102AH
Remove the intake air guide.
8 CLIPS
QC71104BH
2 SELF-TAPPING
SCREWS
(flat head)
4 CLIPS
•
Release four retaining tabs on each side.
FRONT BUMPER
4 RETAINING
TABS
INTAKE
AIR GUIDE
FRONT BUMPER
QC71103AH
QC71105AH
2 of 5
AII 51170 (1404)
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
•
With the help of an assistant, release one
retaining tab on each side.
•
Then remove the front bumper. Place the front
bumper on the blanket to prevent damage.
RETAINING TAB
4 RETAINING TABS
FRONT
BUMPER
FRONT
BUMPER
2 VEHICLE
CONNECTORS
(if equipped)
QC71106AH
FRONT
BUMPER
3.
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
AII 51170 (1404)
QC71107AH
Remove the front grille from the front bumper.
3 of 5
5.
Install the stay to the front grille.
2 CLIPS
FRONT GRILLE
FRONT GRILLE
3 SELF-TAPPING
SCREWS
FRONT
BUMPER
QC90603AH
6.
9 RETAINING
TABS
4.
STAY
Install the front grille to the front bumper.
QC90601AH
2 CLIPS
Remove the stay from the front grille.
FRONT GRILLE
FRONT GRILLE
(Discard.)
9 RETAINING
TABS
FRONT BUMPER
3 SELF-TAPPING
SCREWS
STAY
QC90604AH
QC90602AH
4 of 5
AII 51170 (1404)
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
7.
Check that all wire harnesses are routed properly
and all connectors are plugged in.
8.
Reinstall all removed parts.
9.
Reconnect the negative cable to the battery.
10. Press and hold the radio power button for two
seconds to restore the radio and navi (if equipped)
system functions.
11. Reset the clock.
12. Restore the systems back to normal operation as
described in the Service Manual if necessary.
© 2014 American Honda Motor Co., Inc. – All Rights Reserved.
AII 51170 (1404)
5 of 5