Download cover - Free

DCR-TRV940/TRV940E/TRV950/TRV950E
RMT-811
SERVICE MANUAL
LEVEL
2
US Model
Canadian Model
Ver 1.1 2002. 09
DCR-TRV950
AEP Model
Revision History
DCR-TRV940E/TRV950E
UK Model
DCR-TRV950E
East European Model
North European Model
Russian Model
DCR-TRV940E/TRV950E
E Model
DCR-TRV940/TRV940E/TRV950/TRV950E
Hong Kong Model
DCR-TRV940/TRV950E
Australian Model
DCR-TRV950E
Chinese Model
DCR-TRV940E
Korea Model
DCR-TRV940
J MECHANISM
Tourist Model
Photo: DCR-TRV950
DCR-TRV940/TRV940E
Link
SPECIFICATIONS
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAMS
REPAIR PARTS LIST
DISASSEMBLY
SCHEMATIC DIAGRAMS
• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (992997851.pdf).
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (992997841.pdf).
• For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL ADJUSTMENT MANUAL VI
J MECHANISM ” (9-929-807-11).
• Reference No. search on printed wiring boards is available.
• Table for differences of function of each model.
• When the laser unit (D501) is repaired.
Make sure to follow the items of “NOTE ON HANDLING THE LASER DIODE”.
On the DB-014, VC-288 boards
This service manual provides the information that is premised the circuit board replacement service and not intended repair
inside the DB-014, VC-288 boards.
Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the DB-014,
VC-288 boards are not shown.
The following pages are not shown.
Schematic diagram ............................. Pages 4-13 to 4-64
Mounted parts location .................. Pages 4-132 to 4-135
Printed wiring board ............................ Pages 4-93 to 4-100 Electrical parts list ......................... Pages 5-17 to 5-23,
Waveforms ........................................... Pages 4-127 to 4-129
5-29 to 5-36
DIGITAL VIDEO CAMERA RECORDER
DCR-TRV940/TRV940E/TRV950/TRV950E
COVER
TM
SERIES
SPECIFICATIONS
Video camera
recorder
System
Video recording system
2 rotary heads
Helical scanning system
Audio recording system
Rotary heads, PCM system
Quantization: 12 bits (Fs 32 kHz,
stereo 1, stereo 2), 16 bits
(Fs 48 kHz, stereo)
Video signal
TRV940/TRV950:
NTSC color, EIA standards
TRV940E/TRV950E:
PAL color, CCIR standards
Usable cassette
Mini DV cassette with the
mark printed
Tape speed
SP: Approx. 18.81 mm/s
LP: Approx. 12.56 mm/s
Recording/playback time (using
cassette DVM60)
SP: 1 hour
LP: 1.5 hours
Fastforward/rewind time (using
cassette DVM60)
When using the battery pack:
Approx. 2 min. and 30 seconds
When using the AC power
adaptor:
Approx. 1 min. and 45 seconds
Viewfinder
Electric viewfinder (color)
Image device
3.8 mm (1/4.7 type) 3 CCD
(Charge Coupled Device)
Gross: Approx. 1 070 000 pixels
Effective (still):
Approx. 1 000 000 pixels
Effective (moving):
Approx. 690 000 pixels
Lens
Combined power zoom lens
Filter diameter: 37 mm
(1 1/2 in)
12× (Optical), 150× (Digital)
F 1.6 – 2.8
Focal length
3.6 – 43.2 mm (5/32 – 1 3/4 in.)
When converted to a 35 mm still
camera
In CAMERA
49 – 588 mm (1 15/16 – 23 1/4 in.)
In MEMORY
41 – 492 mm (1 5/8 – 19 3/8 in.)
Color temperature
Auto, nIndoor (3 200 K),
Outdoor (5 800 K),
Minimum illumination
7 lx (lux) (F 1.6)
1)
Input/Output connectors
S video input/output
TRV940/TRV950:
4-pin mini DIN
Luminance signal: 1 Vp-p,
75 Ω (ohms), unbalanced
Chrominance signal: 0.286 Vp-p,
75 Ω (ohms), unbalanced
TRV940E/TRV950E:
4-pin mini DIN
Luminance signal: 1 Vp-p,
75 Ω (ohms), unbalanced
Chrominance signal: 0.3 Vp-p,
75 Ω (ohms), unbalanced
Audio/Video input/output
AV MINI JACK, 1 Vp-p,
75 Ω (ohms), unbalanced, sync
negative
327 mV, (at output impedance
more than 47 kΩ (kilohms))
Output impedance with less than
2.2 kΩ (kilohms)/Stereo minijack
(ø 3.5 mm)
Input impedance more than
47 kΩ (kilohms)
DV input/output
4-pin connector
Headphone jack
Stereo minijack (ø 3.5 mm)
LANC jack
Stereo mini-minijack (ø 2.5 mm)
USB jack
mini-B
MIC jack
Minijack, 0.388 mV low impedance
with 2.5 to 3.0 V DC, output
impedance 6.8 kΩ (kilohms) (ø 3.5
mm)
Stereo type
LCD screen
Picture
8.8 cm (3.5 type)
72.2 × 50.4 mm (2 7/8 × 2 in.)
Total dot number
246 400 (1 120 × 220)
2)
3)
Max. baud rate of Bluetooth
standard Ver.1.1
Varies according to the distance
between communicating
devices, presence of obstacles,
radiowave conditions, and other
factors.
This is a specification matched
to specific usage requirements
between Bluetooth compatible
devices. It is laid down in the
Bluetooth standards.
General
Power requirements
7.2 V (battery pack)
8.4 V (AC power adaptor)
Average power consumption
(when using the battery pack)
During camera recording using
LCD
TRV940/TRV950:
6.3 W
TRV940E/TRV950E:
6.0 W
Viewfinder
TRV940/TRV950:
4.9 W
TRV940E/TRV950E:
4.7 W
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
–20°C to + 60°C
(–4°F to + 140°F)
Dimensions (Approx.)
93 × 99 × 202 mm
(3 3/4 × 4 × 8 in.) (w/h/d)
Mass (Approx.)
DCR-TRV950/TRV950E:
970 g (2 lb 2 oz)
DCR-TRV940/TRV940E:
960 g (2 lb 1 oz)
main unit only
1.1kg (2 lb 6 oz)
including the battery pack
NP-FM50, cassette DVM60,
lens cap and Shoulder strap
Wireless communications
(DCR-TRV950/TRV950E only)
Communications system
Bluetooth standard Ver.1.1
Max. baud rate1) 2)
Approx. 723 kbps
Output
Bluetooth standard Power Class 2
Communications distance2)
Max. wireless distance
Approx. 10 m (393 3/4 in.) (When
connecting to BTA-NW1/NW1A)
Compatible Bluetooth profile3)
Generic Access Profile
Dial-up Networking Profile
Operating frequency band
2.4 GHz band (2.400 GHz –
2.483 5 GHz)
AC power adaptor
Power requirements
100 – 240 V AC, 50/60 Hz
Power consumption
23 W
Output voltage
DC OUT: 8.4 V, 1.5 A in the
operating mode
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
–20°C to + 60°C
(–4°F to + 140°F)
Dimensions (approx.)
125 × 39 × 62 mm
(5 × 1 9/16 × 2 1/2 in.) (w/h/d)
excluding projecting parts
Mass (approx.)
280 g (9.8 oz)
TRV940/TRV950:
excluding power cord
TRV940E/TRV950E:
excluding mains lead
—2—
Battery pack
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
8.5 Wh (1 180 mAh)
Dimensions (approx.)
38.2 × 20.5 × 55.6 mm
(1 9/16 × 13/16 × 2 1/4 in.)
(w/h/d)
Mass (approx.)
76 g (2.7 oz)
Type
Lithium ion
“Memory Stick”
Memory
Flash memory
8MB: MSA-8A
Operating voltage
2.7 – 3.6 V
Power consumption
Approx. 45 mA in the operating
mode
Approx. 130 µA in the standby
mode
Dimensions (approx.)
50 × 2.8 × 21.5 mm
(2 × 1/8 × 7/8 in.) (w/h/d)
Mass (approx.)
4 g (0.14 oz)
Design and specifications are
subject to change without notice.
DCR-TRV940/TRV940E/TRV950/TRV950E
Supplied accessories
1
2
3
5
6
7
8
9
q;
qa
qs
qd
qf
1 AC-L10A/L10B/L10C AC power
adaptor (1), power cord (1)
2 NP-FM50 battery pack (1)
3 A/V connecting cable (1)
4 Wireless Remote Commander (1)
5 Size AA (R6) battery for Remote
Commander (2)
6 Shoulder strap (1)
7
8
9
0
qa
4
qg
Lens cap (1)
“Memory Stick” (1)
USB cable (1)
CD-ROM (SPVD-008 USB Driver) (1)
Cleaning cloth (1)
qs Stylus (1) (DCR-TRV950/TRV950E only)
qd 21-pin adaptor (1)
AEP, UK, EE, NE, RU
qf 2-pin conversion adaptor (1)
E, HK
qg 2-pin conversion adaptor (1)
JE
Table for differences of function
Model
Destination
Color system
Wireless communications
BT board
DCR-TRV940
DCR-TRV940E
NTSC
AEP, EE, NE,
RU, E, CH, JE
PAL
✕
–
✕
–
E, HK, KR, JE
Note: BT-003 board is only replaced as a mounted board.
Therefore, schematic diagrams and printed wiring boards are not shown.
• Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
JE : Tourist model
KR : Korean model
NE : North European model
RU : Russian model
—3—
DCR-TRV950
DCR-TRV950E
NTSC
AEP, UK, EE, NE,
RU, E, HK, AU
PAL
a
BT-003 (Note)
a
BT-003 (Note)
US, CND, E
DCR-TRV940/TRV940E/TRV950/TRV950E
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or eqivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
—4—
DCR-TRV940/TRV940E/TRV950/TRV950E
TABLE OF CONTENTS
Section
1.
Title
Page
SERVICE NOTE
4.
1-1. Note for Repair ································································ 1-1
1-2. Discharging of the Flash Unit’s Charging Capacitor ······ 1-1
1-2-1. Preparing the Short Jig ···················································· 1-1
1-2-2. Discharging the Capacitor ··············································· 1-1
1-3. Power Supply During Repairs ········································· 1-2
1-4. To Take Out a Cassette when not Eject (Force Eject) ····· 1-2
1-5. Notes on Handling the Laser Diode
[Laser Unit (D501)] ························································· 1-3
1-5-1. Soldering Conditions of Laser Unit (D501) ···················· 1-3
1-6. Self-diagnosis Function ··················································· 1-4
1-6-1. Self-diagnosis Function ··················································· 1-4
1-6-2. Self-diagnosis Display ····················································· 1-4
1-6-3. Service Mode Display ····················································· 1-4
1-6-4. Self-diagnosis Code Table ··············································· 1-5
2.
Section
DISASSEMBLY
2-1. Cabinet (R) Block ···························································· 2-2
2-2. P Cabinet (C) ··································································· 2-2
Service Position to Check PD-168 Board ······················· 2-3
2-3. LCD Module ···································································· 2-3
2-4. LCD Block ······································································ 2-4
2-5. FP-495 Flexible Board ···················································· 2-4
2-6. CK-116 Board ································································· 2-5
2-7. F Panel Block ·································································· 2-5
Service Position to Check MA-410 Board ······················ 2-6
2-8. AF Laser Bracket Assembly ············································ 2-6
2-9. MA-410 Board ································································ 2-7
2-10. FP-504 Flexible Board ···················································· 2-7
2-11. Battery Panel Block ························································· 2-8
2-12. BT-003 Board (TRV950/TRV950E) ································ 2-8
2-13. ST Frame Block ······························································· 2-9
2-14. DB-014 Board ································································· 2-9
2-15. MD Block ······································································ 2-10
2-16. Lens Block ····································································· 2-11
2-17. VC-288 Board ······························································· 2-11
2-18. Mechanism Deck (J200) ················································ 2-12
2-19. Stroboscope Block ························································· 2-12
2-20. JK-222 Board ································································ 2-13
Service Position to Check the Camera Section ············· 2-13
Service Position to Check the VTR Section ·················· 2-14
2-21. Flash Unit ······································································ 2-15
2-22. EVF Block ····································································· 2-15
2-23. FP-497 Flexible Board ·················································· 2-16
2-24. Control Switch Block (PS-1870) ··································· 2-17
2-25. SE-132 Board ································································ 2-17
2-26. Grip Cabinet Block ························································ 2-18
2-27. Control Switch Block (CF-1870) ·································· 2-19
2-28. MS Assembly ································································ 2-19
2-29. VF lens Assembly ·························································· 2-20
2-30. Circuit Boards Location ················································ 2-21
2-31. Flexible Boards Location ·············································· 2-22
3.
BLOCK DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
Overall Block Diagram (1/4) ··········································· 3-1
Overall Block Diagram (2/4) ··········································· 3-3
Overall Block Diagram (3/4) ··········································· 3-5
Overall Block Diagram (4/4) ··········································· 3-7
Power Block Diagram (1/3) ············································· 3-9
Power Block Diagram (2/3) ··········································· 3-11
Power Block Diagram (3/3) ··········································· 3-13
Title
Page
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagrams
Frame Schematic Diagram (1/3) ····································· 4-1
Frame Schematic Diagram (2/3) ····································· 4-3
Frame Schematic Diagram (3/3) ····································· 4-5
4-2. Schematic Diagrams ························································ 4-9
CD-389 (CCD IMAGER) ·············································· 4-11
SE-132 (PITCH/YAW SENSOR) ·································· 4-65
MA-410 (MIC AMP, AF LASER CONTROL) ············· 4-67
CK-116 (CONTROL SWITCH) ··································· 4-69
JK-222 (AV IN/OUT, DV/USB CONNECTOR) ·········· 4-71
PD-168 (1/2)
(LCD DRIVER, TIMING GENERATOR) ··················· 4-73
PD-168 (2/2) (LCD DRIVER, BACKLIGHT) ············· 4-75
LB-080 (EVF, EVF BACKLIGHT) ······························ 4-77
FP-504 FLEXIBLE ······················································· 4-79
FP-495, FP-497, FP-500, FP-503 FLEXIBLE ·············· 4-81
FP-100, FP-102, FP-228 FLEXIBLE ···························· 4-83
CONTROL SWITCH BLOCK
(CF-1870, KP-1870, PS-1870) ······································ 4-85
4-3. Printed Wiring Boards ··················································· 4-87
CD-389 ·········································································· 4-89
SE-132 ········································································· 4-101
MA-410 ······································································· 4-103
CK-116 ········································································ 4-105
JK-222 ········································································· 4-109
PD-168 ········································································· 4-113
LB-080 ········································································· 4-115
FP-504 FLEXIBLE ····················································· 4-117
FP-495, FP-497 FLEXIBLE ········································ 4-121
FP-100, FP-102, FP-228 FLEXIBLE ·························· 4-123
4-4. Waveforms ··································································· 4-125
4-5. Mounted Parts Location ·············································· 4-131
5.
REPAIR PARTS LIST
5-1.
Exploded Views ···························································· 5-1
5-1-1. Main Section ································································· 5-1
5-1-2. F Panel Block ································································ 5-2
5-1-3. Cabinet (R) Block ························································· 5-3
5-1-4. LCD Block ···································································· 5-4
5-1-5. Cabinet (L) Block ························································· 5-5
5-1-6. Grip Cabinet Block ······················································· 5-6
5-1-7. Stroboscope Block ························································ 5-7
5-1-8. EVF Block ···································································· 5-8
5-1-9. Battery Panel Block ······················································ 5-9
5-1-10. MD Block ··································································· 5-10
5-1-11. Lens Block ·································································· 5-11
5-1-12. Overall Mechanism Deck Section (J200) ··················· 5-12
5-1-13. LS Chassis Block Assembly ······································· 5-13
5-1-14. Mechanism Chassis Block Assembly ························· 5-14
5-2.
Electrical Parts List ····················································· 5-15
—5—
DCR-TRV940/TRV940E/TRV950/TRV950E
SECTION 1
SERVICE NOTE
COVER
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
1-2. DISCHARGING OF THE FLASH UNIT’S CHARGING CAPACITOR
1-2-2. Discharging the Capacitor
The charging capacitor of the Flash unit is charged up to the
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
battery is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
R: 1 kΩ/1 W
(Part code:
1-215-869-11)
1-2-1. Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
1 kΩ/1 W
Wrap insulating tape.
Capacitor
1-1
DCR-TRV940/TRV940E/TRV950/TRV950E
1-3. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
These following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the AC power adaptor (AC-L10, AC-VQ800 etc.).
Method 2.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
1-4. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
2
3
4
5
6
7
Refer to 2-2 to remove the cabinet (R) block assembly.
Refer to 2-7 to remove the F panel block.
Refer to 2-11 to remove the battery panel block.
Refer to 2-13 to remove the ST frame block.
Refer to 2-14 to remove the DB-014 board.
Refer to 2-15 to remove the MD block.
Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
DC power supply
(+4.5Vdc)
: Unloading
: Loading
Disconnect from CN1006 (27P)
of VC-288 board
Loading motor
1-2
DCR-TRV940/TRV940E/TRV950/TRV950E
1-5. NOTES ON HANDLING THE LASER DIODE
[LASER UNIT (D501)]
The laser diode may suffer electrostatic breakdown because of the
potential difference generated by the charged electrostatic load, etc.
on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
1-5-1. Soldering Conditions of Laser Unit (D501)
Temperature of
the Soldering Iron
Time to Solder
Interval to Solder
350 °C
3 seconds
Next terminal is soldered after
waiting for 1 second
Note: Adjustment is needed when laser unit (D501) is replaced.
Refer to “20. Hologram AF Output Adjustment” and “21.
Hologram AF Angle Check” of SERVICE MANUAL, ADJ
(992997851.pdf).
Laser unit
(D501)
1-3
DCR-TRV940/TRV940E/TRV950/TRV950E
1-6. SELF-DIAGNOSIS FUNCTION
1-6-1. Self-diagnosis Function
1-6-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or Display
window what to do. This function consists of two display; selfdiagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
When problems occur while the unit is operating, the counter of the
viewfinder or Display window shows a 4-digit display consisting
of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
Viewfinder
Display window
C : 3 1 : 11
C:31:11
Blinks at 3.2Hz
Display window
C
Repaired by:
31
Block
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
11
Detailed Code
Refer to “1-6-4. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
1-6-3. Service Mode Display
The service mode display shows up to six self-diagnosis codes shown in the past.
1.
Display Method
While pressing the “STOP” key, set the switch from OFF to “VCR”, and continue pressing the “STOP” key for 5 seconds continuously. The
service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
Viewfinder
Display window
3 C : 3 1 : 11
[3] C : 3 1 : 1 1
Lights up
[3]
Backup No.
C:31:11
Self-diagnosis Codes
Control dial
Order of previous errors
2.
Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time
[4] : Occurred fourth time
[2] : Occurred second time [5] : Occurred fifth time
[3] : Occurred third time
[6] : Occurred the last time
3.
End of Display
Turning OFF the power supply will end the service mode display.
Note: The “self-diagnosis display” data will not be erased (reset) when the lithium 3 V supply (CK-116 board BT5201) is removed.
1-4
DCR-TRV940/TRV940E/TRV950/TRV950E
1-6-4. Self-diagnosis Code Table
Repaired by:
Self-diagnosis Code
Block
Detailed
Function
Code
Symptom/State
Correction
C
C
C
0
2
2
4
1
2
0
0
0
0
0
0
C
3
1
1
0
C
3
1
1
1
C
3
1
2
0
C
3
1
2
1
C
C
C
C
C
C
3
3
3
3
3
3
1
1
1
1
1
1
2
2
2
3
4
4
2
3
4
0
0
2
C
3
1
1
0
C
3
1
1
1
C
3
2
2
0
C
3
2
2
1
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
Winding S reel fault when counting the
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
LOAD direction loading motor timeout.
UNLOAD direction loading motor
time-out.
T reel side tape slacking when
unloading.
Winding S reel fault when counting the
rest of tape.
C
3
2
2
2
T reel fault.
C
3
2
2
3
S reel fault.
C
3
2
2
4
T reel fault.
C
3
2
3
0
FG fault when starting capstan.
C
3
2
4
0
FG fault when starting drum
C
3
2
4
2
E
2
0
0
0
FG fault during normal drum
operations
EEPROM data error
E
6
1
0
0
Difficult to adjust focus
(Cannot initialize focus.)
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
E
6
2
0
0
E
6
2
0
1
E
9
1
0
1
Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
Abnormality when flash is being charged.
1-5E
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Initialize A, D page data (EEPROM data).
Inspect the lens block focus MR (Pin qf, qg of DB-014 board
CN1004) when focusing is performed when the focus ring is rotated
in the focus manual mode, and the focus motor drive circuit (IC3402
of DB-014 board) when the focusing is not performed.
Inspect the lens block zoom MR (Pin 0, qs of DB-014 board
CN1004) when zooming is performed when the zoom lens is
operated and the zoom motor drive circuit (IC3402 of DB-014
board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE4001 of SE-132 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE4002 of SE-132 board)
peripheral circuits.
Checking of flash unit or replacement of flash unit.
DCR-TRV940/TRV940E/TRV950/TRV950E
SECTION 2
DISASSEMBLY
COVER
• This set can be disassembled in the order shown below.
DCR-TRV940/TRV940E/TRV950/TRV950E
2-1. CABINET (R) BLOCK
(Page 2-2)
2-29. VF LENS ASSY
(Page 2-20)
2-2. P CABINET (C)
(Page 2-2)
SERVICE POSITION TO
CHECK PD-168 BOARD
(Page 2-3)
2-3. LCD MODULE
(Page 2-3)
2-4. LCD BLOCK
(Page 2-4)
2-6. CK-116 BOARD
(Page 2-5)
2-7. F PANEL BLOCK
(Page 2-5)
2-5. FP-495
FLEXIBLE BOARD
(Page 2-4)
SERVICE POSITION
(MA-410 BOARD)
(Page 2-6)
2-8. AF LASER BRACKET
ASSEMBLY
(Page 2-6)
2-10. FP-504
FLEXIBLE BOARD
(Page 2-7)
2-9. MA-410 BOARD
(Page 2-7)
2-26.GRIP CABINET
BLOCK
(Page 2-18)
2-24. CONTROL SWITCH
BLOCK (PS-1870)
(Page 2-17)
2-25.SE-132 BOARD
(Page 2-17)
2-27. CONTROL SWITCH
BLOCK (CF-1870)
(Page 2-19)
2-28. MS ASSEMBLY
(Page 2-19)
2-21. FLASH UNIT
(Page 2-15)
DCR-TRV950/TRV950E
2-11. BATTERY PANEL
BLOCK (Page 2-8)
2-12. BT-003 BOARD
(Page 2-8)
2-13. ST FRAME BLOCK
(Page 2-9)
2-15. MD BLOCK
(Page 2-10)
2-14. DB-014 BOARD
(Page 2-9)
2-16. LENS BLOCK
(Page 2-11)
2-19. STROBOSCOPE
BLOCK (Page 2-12)
2-17. VC-288 BOARD
(Page 2-11)
2-22. EVF BLOCK
(Page 2-15)
2-20. JK-222 BOARD
(Page 2-13)
2-18. MECHANISM DECK
(J200) (Page 2-12)
2-23. FP-497
FLEXIBLE BOARD
(Page 2-16)
SERVICE POSITION TO
CHECK THE CAMERA
SECTION (Page 2-13)
SERVICE POSITION TO
CHECK THE VTR
SECTION (Page 2-14)
2-1
DCR-TRV940/TRV940E/TRV950/TRV950E
Note: Follow the disassembly procedure in the numerical order given.
2-1. CABINET (R) BLOCK
5 FP-496 flexible board
(CN5203)
4 Cabinet (R) block
3 Three screws (M1.7)
1 Two screws (M1.7)
2 Open the LCD panel.
2-2. P CABINET (C)
8 P cabinet (C)
2 Screw
(M1.7)
1 Turn the LCD panel.
4 Screw
(M1.7)
5 Two screws
(M1.7)
3 Turn the LCD panel.
7 Claw
6 Two claws
2-2
DCR-TRV940/TRV940E/TRV950/TRV950E
[SERVICE POSITION TO CHECK PD-168 BOARD]
Adjustment remote
commander (RM-95)
CN1024
CPC jig for LCD panel
(J-6082-529-A)
1
6
D
P
8
6
-1
AC power
adaptor
DC-IN
PD-168 board
Inverter transformer unit
2-3. LCD MODULE
5 Back light unit
6 LCD module
7 Cushion (L)
8 Touch panel
9 Cushion (C)
4 P cabinet (M) block
0 Ground plate (P)
1 Flexible board
(LCD module)
(CN5701)
2 Flexible board
(touch panel)
(CN5803)
3 Flexible board
(back light unit)
(CN5805)
P cabinet (M)
2-3
DCR-TRV940/TRV940E/TRV950/TRV950E
2-4. LCD BLOCK
1 FP-495 flexible board
(CN5206)
3 Hinge blind lid assemby
2 Three screws
(M1.7)
7 LCD block
4 Two harness (PC-087, 088)
(CN5201, 5202)
Hinge blind lid assembly
5 Five screws
(M1.7)
6 Cabinet (hinge)
Harness (PC-087)
Harness (PC-088)
Note: When installing Hinge blind lid assembly,
please attach, as shown in a figure.
2-5. FP-495 FLEXIBLE BOARD
Note: When installing FP-495 flexible board
and harness, please attach, as shown
in a figure.
S001
FP-495 flexible board
Note: When installing FP-495 flexible board,
please attach, as shown in a figure.
1 Screw
(M1.7 × 2.5)
S001
harness
SW lever
7 Hinge cover (rear)
2
4 Screw
(M1.7 × 2.5)
3 Two screws
(M1.7)
8 Screw
(M1.7 × 2.5)
5 Two claws
S002
6 Hinge cover (front)
9 FP-495 flexible board
2-4
DCR-TRV940/TRV940E/TRV950/TRV950E
2-6. CK-116 BOARD
S5201
8 CK-116 board
7 Three screws (M1.7)
1 Harness (PC-088)
(CN5202)
C
K
-1
16
6 Three screws (M1.7)
2 Harness (PC-088)
(CN5201)
S5202
4 Harness (speaker)
(CN5204)
3 FP-495 flexible board
(CN5206)
Knob (auto lock)
5 Flexible board (KP1870)
(CN5205)
Knob (zebra)
Note: When installing CK-116 board, connect knob (auto lock)
with S5201 and knob (zebra) with S5202.
2-7. F PANEL BLOCK
6 Screw (M1.7)
5 Open the
jack cover.
4 Screw (M1.7)
1 FP-494 flexible board
(CN5906)
2 Screw (M1.7)
3 Screw (M1.7)
8 Flexible board (JK-222)
(CN5904)
Note: Remove it while taking care as
the flexible board is connected.
7 F panel block
2-5
DCR-TRV940/TRV940E/TRV950/TRV950E
[SERVICE POSITION TO CHECK MA-410 BOARD]
AC power
adaptor
MA-410 board
10
-4
MA
Monitor
Adjustment remote
commander (RM-95)
2-8. AF LASER BRACKET ASSEMBLY
3 AF laser bracket assembly
1 FP-500 flexible board
(CN5903)
2 Two screws
(M1.7 × 4)
2-6
AC IN
DCR-TRV940/TRV940E/TRV950/TRV950E
2-9. MA-410 BOARD
7 Two screws
(M1.7 × 4)
2 FP-500 flexible board
(CN5903)
3 FP-504 flexible board
(CN5905)
6 Two connectors
(CN5901, 5902)
1 Open microphone jack cover.
8 MA-410 board
5
4 Two screws
(M1.7 × 4)
2-10.FP-504 FLEXIBLE BOARD
7 Screw (M1.7 × 4)
qf FP-504 flexible board
0 Ornamental plate
qd Three screws
(M1.7 × 2.5)
6 Screw
(M1.7 × 2.5)
9
8 Screw (M1.7 × 4)
S601
3 Two screws
(M1.7 × 4)
5 Screw
(M1.7 × 4)
1 Screw
(M1.7 × 4)
4 Microphone grille
2 Bracket
2-7
qs MF knob retainer
qa MF knob
Note: When installing FP-504 flexible board,
connect MF knob with S601.
DCR-TRV940/TRV940E/TRV950/TRV950E
2-11.BATTERY PANEL BLOCK
5 Lift the view finder.
4 Three screws (M1.7)
3 Screw (M1.7)
7 Battery panel block
6
1 Harness (BT terminal)
(CN7202)
2 Screw (M1.7)
2-12.BT-003 BOARD
(TRV950/TRV950E)
1 FP-491 flexible board
BT-003
2 Antenna
4 BT-003 board
3 Two screws
2-8
DCR-TRV940/TRV940E/TRV950/TRV950E
2-13.ST FRAME BLOCK
1 Flexible board
(flash unit) 2 FP-493 flexible board
6 ST frame block
3 FP-491 flexible board
(TRV950/TRV950E)
4 Antenna
(TRV950/TRV950E)
5 Three screws (M1.7 × 2.5)
Note: High-voltage cautions.
(See page 1-1)
Note: This part is included in flash unit.
2-14.DB-014 BOARD
4 DB-014 board
DB
1 Flexible board (lens block)
(CN1004)
3 Two screws
(M1.7 × 2.5)
2-9
-01
4
2 Flexible board (lens block)
(CN1501)
DCR-TRV940/TRV940E/TRV950/TRV950E
2-15.MD BLOCK
3 CCD heat sink (R)
4 CCD heat sink (G)
5 CCD heat sink (B)
1 Screw
(M1.7 × 2.5)
2 MF knob retainer plate
qh Screw
(M1.7 × 2.5)
6 FP-547 flexible board
(CN7211)
7 FP-497 flexible board
(CN7205)
8 FP-503 flexible board
(CN1009)
DB-014
qg Open the
jack cover.
VC-288
qd Screw
(M1.7 × 2.5)
qj MD block
qf Screw
(M1.7 × 2.5)
9 Flexible board (CF1870)
(CN7200)
0 Flexible board (PS1870)
(CN7201)
qs Screw
(M1.7 × 2.5)
qa Two flexible boards (JK-222)
(CN1005, 7204)
2-10
DCR-TRV940/TRV940E/TRV950/TRV950E
2-16.LENS BLOCK
3 Flexible board (CD-389)
(CN1201)
1 Screw
(M1.7 × 2.5)
4 Two screws
2 Heat sink bracket
5 Lens block
2-17.VC-288 BOARD
5 Claw
4 Screw
(M1.7 × 2.5)
8
6 VC-288 board
28
VC
3 Screw
(M1.7 × 2.5)
2 Screw
(M1.7 × 2.5)
1 Four flexible boards (Mechanism deck)
(CN1006, 1007, 1022, 1901)
2-11
DCR-TRV940/TRV940E/TRV950/TRV950E
2-18.MECHANISM DECK (J200)
2 Mechanism deck
(J200)
1 Four screws
(M1.4 × 1.5)
2-19.STROBOSCOPE BLOCK
CS frame
2 Two claws
Antenna
Note: When installing stroboscope block,
please attach, as shown in a figure.
3 Stroboscope block
1 Two screws
(M1.7 × 6)
2-12
DCR-TRV940/TRV940E/TRV950/TRV950E
2-20.JK-222 BOARD
2 Open the jack cover.
6 JK-222 board
3 Two screws
(M1.7 × 4)
JK
-2
2
2
1 Flexible board
(CN4005)
5 Screw
(M1.7 × 4)
4 Screw
(M1.7 × 4)
[SERVICE POSITION TO CHECK THE CAMERA SECTION]
Connection to Check the Camera Section
To check the camera section, set the camera to the Forced camera power ON mode.
Operate the camera functions of the zoom and focus using the adjustment remote commander (with the HOLD switch set in
the OFF position).
Setting the Forced Camera Power ON mode
AC IN
1) Select page: O, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01 and
press the PAUSE button of the adjustment remote
commander.
AC power
adaptor
Battery panel block
Exiting the Forced Camera Power ON mode
DB-014 board
1) Select page: O, address: 01, and set data: 01.
2) Select page: D, address: 10, data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page : 0, address: 01, and set data: 00.
FP-499 flexible board
DB
FP-498 flexible board
JK-222 board
-01
4
VC-288 board
JK
-22
2
88
-2
C
V
Adjustment remote
commander (RM-95)
Mechanism deck
Extention cable
(J-6082-466-A)
Lens block
CD-389 board
2-13
Monitor
DCR-TRV940/TRV940E/TRV950/TRV950E
[SERVICE POSITION TO CHECK THE VTR SECTION]
Connection to Check the VTR Section
To check the VTR section, set the VTR to the Forced VTR power ON mode. (Or, connect the control switch block (PS-1870)
to the CN7201 of DB-014 board and set the power switch to the VIDEO position.)
Operate the VTR function using the adjustment remote commander (with the HOLD switch set in the OFF position).
Setting the Forced VTR Power ON mode
Exiting the Forced VTR Power ON mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02 and
press the PAUSE button of the adjustment remote
commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
When exiting the Forced VTR Power ON mode, connect the control
switch block (PS-1870) to the CN7201 of DB-014 board. Or,
when ejecting the cassette, connect the control switch block (PS-1770)
to the CN402 of ME-020 board. and press the EJECT switch.
AC IN
Control switch block
(PS-1870)
Eject switch
AC power
adaptor
Battery panel block
DB-014 board
14
-0
B
D
FP-498 flexible board
CPC-8 jig
(J-6082-388-A)
Mechanism deck
-2
C
V
JK-222 board
88
JK
VC-288 board
2
FP-499 flexible board
Monitor
2-14
-22
Adjustment remote
commander (RM-95)
DCR-TRV940/TRV940E/TRV950/TRV950E
2-21.FLASH UNIT
6 ST cabinet (upper)
5 Two claws
7 Remove the flexible board
from two claws.
3 Screw
(M1.7 × 4)
8 Screw (M1.7)
2 Screw
(M1.7 × 4)
9 ST cover (upper)
4 Two claws
Note: High-voltage cautions.
(See page 1-1)
qh Flash unit
qs ST insulating sheet
qd Two screws
(M1.7 × 4)
Note: High-voltage cautions.
(See page 1-1)
0 Screw (M1.7)
qa Screw
qf ST cabinet (lower)
qg Two claws
1 Push the lever.
2-22.EVF BLOCK
1 Three screws
(M1.7)
2 EVF block
2-15
DCR-TRV940/TRV940E/TRV950/TRV950E
2-23.FP-497 FLEXIBLE BOARD
3 Top cabinet assy
7 Screw
(M1.7 × 2.5)
2 Two screws
(M1.7)
8 FP-497 flexible board
1
6 External connector
5
4 Two screws
(M1.7 × 2.5)
FP-547 flexible board
FP-497 flexible board
Note: When installing FP-497 flexible board
and FP-547 flexible board,
please attach, as shown in a figure.
2-16
DCR-TRV940/TRV940E/TRV950/TRV950E
2-24.CONTROL SWITCH BLOCK (PS-1870)
1 Two screws
(M1.7 × 2.5)
3 Control switch block
(PS-1870)
2 Two screws
(M1.7 × 4)
2-25.SE-132 BOARD
3 Two screws
(M1.7 × 4)
SE-132
4 CS frame
5 Three screws
(M1.7 × 2.5)
2 Two screws
(M1.7 × 4)
6 SE-132 board
1 Flexible board (JK-222)
(CN4005)
2-17
DCR-TRV940/TRV940E/TRV950/TRV950E
2-26.GRIP CABINET BLOCK
2 Slide open knob.
3 Open grip cabinet block.
Grip cabinet block
1 four screws
(M1.7 × 4)
4 six bosses
5 grip cabinet block
2-18
DCR-TRV940/TRV940E/TRV950/TRV950E
2-27.CONTROL SWITCH BLOCK (CF-1870)
2 Control switch block
(CF-1870)
1 Two screws
(M1.7 × 4)
2-28.MS ASSEMBLY
3 claw
4 MS assembly
1 Screw
(M1.7 × 4)
2 Two screws
(M1.7 × 2.5)
2-19
DCR-TRV940/TRV940E/TRV950/TRV950E
2-29.VF LENS ASSEMBLY
1
2 Two screws
(M1.7 × 6)
3 Two claws
4 VF cabinet (upper)
6 VF lens assembly
5 FP-547 flexible board
(CN6102)
2-20
DCR-TRV940/TRV940E/TRV950/TRV950E
2-30.CIRCUIT BOARDS LOCATION
BT-003
LB-080
VC-288
CD-389
JK-222
CK-116
PD-168
DB-014
SE-132
MA-410
Board Name
Function
BT-003
BLUE TOOTH
(TRV950/TRV950E) (BT-003 board is only replaced as a mounted board.
Therefor, schematic diagrams and printed wiring boards are not shown.)
CD-389
CCD IMAGER
CK-116
CONTROL SWITCH
DB-014
LENS MOTOR DRIVE, VAP DRIVER, MIC VOL, AUDIO PROCESS,
VIDEO IN/OUT, EVF DRIVE, TIMING GENERATOR, CONNECTOR,
DC/DC CONTROL
JK-222
AV IN/OUT, DV/USB CONNECTOR
LB-080
EVF, EVF BACK LIGHT
MA-410
MIC AMP, AF LASER CONTROL
PD-168
LCD DRIVER TIMING GENERATOR, BACK LIGHT
SE-132
PITCH/YAW SENSOR
VC-288
A/D CONVERTER, TIMING GENERATOR, CAMERA RGB PROCESS,
CAMERA PROCESS, MPEG MOVIE/DIGITAL STILL PROCESS,
HI CONTROL, DIGITAL STILL CONTROL, FLASH MEMORY,
SDRAM, DV SIGNAL PROCESS, DV INTERFACE, REC/PB AMP,
USB INTERFACE, VIDEO A/D CONVERTER,
DRUM/CAPSTAN/LOADING DRIVE, CAMERA/MECHA CONTROL,
HI CONTROL, LANC, RESET, BEEP, AFLD, CONNECTOR, EVR
2-21
DCR-TRV940/TRV940E/TRV950/TRV950E
2-31.FLEXIBLE BOARDS LOCATION
FP-547
Control switch block
(CF-1870)
FP-497
Control switch block
(PS-1870)
FP-495
Control switch block
(KP-1870)
FP-503
FP-500
FP-491
(TRV950/TRV950E)
FP-493
FP-498
FP-496
FP-499
FP-494
FP-504
2-22E
DCR-TRV940/TRV940E/TRV950/TRV950E
COVER
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/4)
POWER BLOCK DIAGRAM (1/3)
OVERALL BLOCK DIAGRAM (2/4)
POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (3/4)
POWER BLOCK DIAGRAM (3/3)
OVERALL BLOCK DIAGRAM (4/4)
DCR-TRV940/TRV940E/TRV950/TRV950E
SECTION 3
BLOCK DIAGRAMS
COVER
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-1. OVERALL BLOCK DIAGRAM (1/4)
S/H
(B)
13
14
XSHDB,
XSHPB
V1B-V4B, H1B, H2B, RGB
IC100
CCD
IMAGER
(R)
1-4
10 - 12
8
5
4
CCD±R
13
14
XSHDR,
XSHPR
IC103
11
S/H
(R)
V1R-V4R, H1R, H2R, RGR
IC101
8
CCD
IMAGER
(G)
1-4
10 - 12
5
4
CCD±G
13
14
XSHDG,
XSHPG
IC104
11
S/H
(G)
V1G-V4G, H1G, H2G, RGG
IRIS–
IC3401
1
IRIS
METER
IRIS CONTROL 13
(1/9)
28
29
M
1
10
22
25
H
9
12
ND FILTER
METER
FOCUS
MOTOR
M801
ZOOM
MOTOR
M
39
30
H
34
36
M
18
19
MR
14
15
HALL AMP
(1/9)
SO GCAM, SCK GCAM
6
2
FOCUS
MOTOR
DRIVE
14
15
37
38
41
42
ZOOM A±, B±
1
46
IC3404
33
34
12
15
FOCUS/ZOOM
CONTROL
(1/9)
26
ı
28
70
68
11
12
ZOOM
MOTOR
DRIVE
34
36
65
1
ı
4
181
188
ı
190
9
8
Y DRIV A, B
3
4
IC1501
VAP YAW DRIVER
(2/9)
7
1
7
1
6
CAM SO, SI, SCK
6
IC1503
7
3
LPF
(2/9)
IC1502
6
SE-132 BOARD
SE4002
SE4001
8
12
PITCH
SENSOR
8
IC4001
18
PITCH/YAW
SENSOR
2
AMP
128
136
IC2501
(1/2)
1
X2501
20MHz
CAMERA
CONTROL
(13/17)
2
PITCH POS AD, YAW POS AD
11
13
210
211
131
132
YAW AD
PITCH AD
130
129
IFI Y0 - 7
76
ı
83
IFI C0 - 3
IFI C0 - 7
65
ı
72
IFI HD, IFI VD, IFI OE
133
ı
137
140
ı
142
145
146
149
ı
154
MDQ0 - MDQ15
102
ı
109
114
ı
118
121
MA0 - MA13
63
61
59
48
53
12
46
55
4
YAW AD
CAM DD ON
YAW PWM
91 93
95 97
VFI C0 - 3
CHARACTER
GENERATOR
MDQ0 - MDQ15
153
ı
156
158
ı
160
162
ı
170
128
ı
133
137
ı
144
MA0 - MA13
DIGITAL STILL
PROCESS
PITCH AD
ZOOM VR AD
MF A, MF B
MA0 - MA13
MDQ0 - MDQ15
20
ı
26
29
ı
35
87
88
OSD HD, OSD VD
120
ı
123
COL 0 - 3
ADAI2
ADAO2
SFD BCK
47
48
VSP SO, XVSP SCK
11
ı
14
16
18
20
22
27
ı
34
D0 LK - D15 LK
2
ı
9
A16 LK - A23 LK
DSCK
1
OVERALL (2/4)
(PAGE 3-3)
2
OVERALL (3/4)
(PAGE 3-5)
3
OVERALL (4/4)
(PAGE 3-8)
IC1701
64M bit SDRAM
(4/17)
24578
10 11 13
42 44 45
47 48 50
51 53
IFI Y0 - 7
IYF Y0 - 7
IFI C0 - 3
IYF C0 - 3
IFI HD, IFI VD, IFI OE
IFI HD, IFI VD, IFI OE
AFCK
34
IYF Y0 - Y7
52
ı
59
IYF C0 - C7
42
ı
49
VIDEO
A/D CONV.
(11/17)
36
ı
38
SPCK
31
68
IC7001 Y OUT
2
IC7001 C OUT
6
SPCK
64
63
66
VD SO, VD SI, VD SCK
STROBO AIN
STROBO ON
X SYS RST
ZOOM VR AD
LD EVR
CAM DD ON
IC1801
16
17
EVR
(D/A CONV.)
(17/17)
12
FP-504 FLEXIBLE BOARD (1/2)
CN1005 (1/4)
MA-410 BOARD (1/4)
PH601, 602
25
CN5906 (1/2)
3
4
26
05
3-1
VFI HD, VFI VD, VFI OE
25
CN1021(1/3)
2
117
ı
119
61
62
59
AUDIO
IFI HD, IFI VD, IFI OE
CAM SO, CAM SI, CAM SCK
PITCH PWM
VFI Y0 - 7
84
ı
86
IC2001
CN1001
(1/6)
38
40
42
99 101
103 106
108 111
113 115
MPEG MOVIE
PROCESS
95
96
47
45
16
JK-222 BOARD (1/5)
CN4005
YAW
SENSOR
SDRAM
(2/17)
75
77
78
71
73
I HALL AD
ND HALL AD
IC1504
YAW/PITCH/
REF AMP
8
9
(2/9)
VAP PITCH DRIVER
(2/9)
IYF Y0 - Y7
SPCK
AFCK
74
44
IC1704
(4/17)
IC1351
53
5
CN7206
(1/6)
7
4
ı
7
177
85
177
SO GCAM, SCK GCAM
1
6
P DRIV A, B
CAMERA
PROCESSOR
(3/17)
VCK
PITCH PWM, YAW PWM
CN1501
ACTIVE
LENS
ACTUATOR
26
ı
28
63
ı
69
25
22
24
135
6
5
23 ND FILTER
DRIVE
24
FOCUS±
28
76
DQ0-31
35689
11 12 14
32 35 37
38 40 41
43 48 50
51 53 54
56 57 59
77 79 80
82 83 85
86 88
314
ı
316
12
9
7
CAM SO, CAM SI, CAM SCK
209
213
ı
217
220 ADD0-13
ı
224
227
ı
229
310
13
ı
15
CN1002
(1/3)
14
15
12
163
164
PBLK
10 TG-HD, TG-VD, TG-FDL
ı
8
(1/9)
IRIS
DRIVE
300
301
303
CHCK
IC3402
8
7
40
ı
49
PBLK, CLPOB, CHCK
72
74
20
21
C02-9
242 - 245
248
250 - 254
257 - 261
264 - 268
271 - 275
277 - 281
284 285
22 26 29
33 36 37
41 42
GIL0-13
CLPOB
14
149 - 151
154 155
158 159
162 - 165
CAMERA RGB
PROCESSOR
(2/17)
PBLK, CLPOB, CHCK
IC3405
HALL AMP
(1/9)
50
ı
57
IC1301
SO GCAM, SCK GCAM
19
20
16
8
Y02-9
62 - 68
95 - 98
101 - 103
RIL0-13
47
48
30
IC1205
1
31
ı
AGC,
A/D CONV. 12
44
(G)
45
(1/17)
13
16
18
17
7
8
10
11
14
142 146
149 - 151
1
ı
3
169
170
173
ı
175
SPCK
8
ı
10
19
20
16
3 3
4 4
13
16
18
17
7
8
10
11
14
PBLK, CLPOB, CHCK
CN7207 (1/3)
ND DRIVE±
10
12
MR
38
35
36
31
26
28
25
29
32
IC1601
SO GCAM, SCK GCAM
47
48
IC1204
30
1
31
ı
AGC,
A/D CONV. 12
44
(R)
45
(1/17)
21 21
22 22
38
35
36
31
26
28
25
29
32
BIL0-13
19
20
16
IC3403
IRIS+
1
ı
4
M
42
41
44
45
55
57
54
47
46
18 - 20 22
24 - 26 28
30 31 34 35
X1201
37 38 40 42
IC1202
66MHz :TRV940/TRV950 50 - 52 54
54MHz :TRV940E/TRV950E 58 - 60 62
TIMING
46
GENERATOR
(1/17)
47
DB-014 BOARD (1/5)
CN1004
42
41
44
45
55
57
54
47
46
97
96
DATA BUS
11
51 51
50 50
95
IFI C0 - 7
CCD±B
CHCK
124 - 128
131 - 136
141 - 143
IFI Y0 - 7
5
4
IC102
47
48
IC1203
30
1
31
ı
AGC,
A/D CONV. 12
44
(B)
45
(1/17)
CAM SO, CAM SI, CAM SCK
IC105
8
CCD
IMAGER
(B)
1-4
10 - 12
CN1201
CAM SO, CAM SCK
CN100
CAM SO, CAM SCK
IRIS
(SHUTTER)
ADDRESS BUS
CHCK
VC-288 BOARD (1/4)
CAM DD ON
SHUTTER ON
DIRA1, DIRB, EN1
LENS
CD-389 BOARD
IFI HD, IFI VD, IFI OE
LENS BLOCK
Ver 1.1 2002. 09
3. BLOCK DIAGRAMS
3-2
31
30
CN5905 (1/2)
MF A, MF B
8
7
MANUAL
FOCUS
SENSOR
DCR-TRV940/TRV940E/TRV950/TRV950E
3. BLOCK DIAGRAMS
COVER
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
JK-222
BOARD (3/5)
VC-288 BOARD (2/4)
RECCK
RECDT
138
99
97
X2101
24.576MHz
MC BUS (8)
139
83
ı
88
ADDT 0 - 5
PBCK
81
SWP
OVERALL (3/4)
(PAGE 3-5)
4
ATF ERR
167
IC2101
79
DV SIGNAL
PROCESS
(7/17)
MC BUS (10)
170
ı
179
FRRV, TRRV, TRRT
152
153
156
71
73
75
105
106
SPCK
AFCK
63
65
67
48
196
55
59
VFI Y0 - 7
199 201
203 205
207 211
213 215
VFI C0 - 3
13
57
VFI HD, VFI VD, VFI OE
17
21
23
TRCK
LCK
2
3
5
6
TPA, NTPA,
TPB, NTPB
CN401
CN1024
PANEL VG
(DV)
PANEL COM
XHD OUT
DV I/F
(8/17)
COL 0 - 3
190 191
194 195
PANEL B
PANE R
PANEL G
PANE XHD, PANEL XVD
EVF B
EVF R
EVF G
PANEL COM
24
68
VFIO C4 - 7
IC2301
65
82
63
USB I/F
(10/17)
47 48
51 - 54
57 58
IFI HD, IFI VD, IFI OE
27
28
42
DATA BUS
ADDRESS BUS
A1 LK - A20 LK
1 -10 13
16 - 25
48
43
43
15
15
27
28
27
28
9
10
9
10
VD SO, VD SCK
VSP SO, VSP SCK
VFO Y0 -7
VFIO
C4-7
- C7
VFO C4
ND901
(BACK LIGHT)
IC3001
ASDATA
MCLK
79
78
16M bit
SDRAM
(6/17)
IC2905
(1/2)
DIGITAL STILL
CONTROL
(5/17)
39 41 - 45
47 49 51 52
54 56 - 60
21
22
A1 LK - A20 LK
IC2904
2
XTAL OSC
(5/17)
4
1
2
OSD SO, OSD SCK
1
2
7
8
OSD SO, OSD SCK
SP+, SP-
8
6
CN7206 (2/5)
8
12
10
83
81
93
89
91
18
20
64
66
37
35
7
94
21
80
28
25
73
76
98
97
3
4
93
8
11
15
90
86
1
2
SP901
SPEAKER
DB-014 BOARD (2/5)
CN7211
EVF B
EVF G
EVF R
VD SO, VD SCK
VSP SO, VSP SCK
IC4202
46
47
48
40
45
42
TIMING
45
GENERATOR 46
VCO
(7/9)
2
14
ı
17
PANEL XHD 1
21
48
ı
PANEL XVD
24
IC4201
LCD
DRIVER
(7/9)
39
40
VD SO, VD SCK
MEMORY
STICK
MS DIO, MS BS, MS SCLK
AUDIO
A/D CONV.
(10/17)
3
2
IR-L
IR-R
38
40
10
8
9
14
14
3
ı
10
COM
7
VST, VCK, STB, EN, DWN,
11 RGT, HST, HCK2, HCK1, BLK
ı
18
EVF 4.75V
35
USB D±
3-3
CHARACTER
DISPLAY
13
15
14
IC6101
Q6101, 6102
Q7200
LED DRIVE
18
17
LED DA
3
LED ON/OFF
4
19
2
LCD903
COLOR
EVF
UNIT
16
3
ı
12
D6102
(BACK LIGHT)
BACK LIGHT
DRIVE
D6101
(TALLY)
9 10
IC2101 Y OUT
46
IC2101 C OUT
7
28
X7001
13.5MHz
30
IC7001 Y OUT
36
IC7001 C OUT
34
27
30
29
74
71
72
24
20
77
81
IC7001
VIDEO
IN/OUT
(6/9)
CN7204 (2/2)
S Y I/O
S C I/O
VIDEO I/O
18
14
22
1
2
39
48
42
DATA TO SFD
DATA FROM SFD
SFD BCK
FP-497 FLEXIBLE
BOARD (1/2)
6
8
9
12
CN7205 (1/2)
SHOE MIC L
AUDIO
A/D CONV.
D/A CONV.
(4/9)
S Y OUT
S C OUT
Y
C
J401
S VIDEO
ID-2
14 15
62
63
INTELLIGENT
ACCESSORY
SHOE
3
(1/2)
3
2
25
23
15
16
19
17
39 SP±
40
J404
AUDIO/VIDEO
ID-2
IC6001
AUDIO
IN/OUT
(4/9)
Q6004, 6005
54
55
5
7
9
V I/O
L I/O
R I/O
53
51
MS DIO, MS BS, MS SCLK
CN1005 (2/4)
18
19
3
I
18
JK-222
BOARD
(4/5)
63
61
USB D±
CN1009
JK-222 BOARD (2/5)
CN402
(USB)
VB
VG
VR
11
13
12
8
MA-410 BOARD (2/4)
3
5
7
LCD902
CN6102
CN6101
24
22
20
IC7001 Y OUT
IC7001 C OUT
FP-503 FLEXIBLE BOARD
1
2
19
20
LB-080 BOARD
IC6004
239
238
11
ı
14
IC5801
LCD
DRIVER 15
ı
(2/2)
30
184
213
ı
215
187
CN5806 (2/2)
USB D±
62 - 64 66
68 - 70 72
73 75 76 78
79 81 83 - 88
90 92 93
DSCK
IC2302
X2901
48MHz
IC3002
INVERTER
TRANSFORMER
UNIT
BACK LIGHT
DRIVE
2
5
1
P UNREG
VSP SO, VSP SCK
9
8
11
25
D0 LK - D15 LK
05
CN5805
VD SO, VD SCK
VFO HD, VFO VD, VFO OE
66
56
16M bit
FLASH
MEMORY
(6/17)
COLOR
LCD UNIT
18
I
14
10
I
6
Q5801, 5802
PWM
COM OUT
LCD901
11
HCNT, MCLK, CLR, OE, SRT,
RESET, STBYB, GSRT, GPCK, CRES
CN5204
61
33
41
18
20
21
29 - 36
38 - 45
VD SO, VD SCK
EVF TALLY
OVERALL (3/4)
(PAGE 3-5)
43
ı
46
D0 LK - D15 LK
1
2
21
22
OSD SO, OSD SCK
6
DATA TO SFD
DATA FROM SFD
SFD FCK
67
139 140
A16 LK - A23 LK
1
2
CN1001
(2/5)
IYF C0 - 3
A1 LK - A14 LK
41 PANEL XHD, PANEL XVD
45
8
6
8 - 12
15 - 17
20 - 26
29 - 35
27
PANEL 4.6V
41
45
VD SO, VD SCK
VCOM
39
40
CN5802 (1/2)
CN5202 (2/2)
OVERALL (4/4)
(PAGE 3-7)
IYF Y0 - 7
D0 LK - D15 LK
LCD
DRIVER
(1/2)
CN5804
VFO Y0 - 7
VSP SO, VSP SI, XVSP SCK
D0 LK - D15 LK
XHD OUT
VG
40
IC5701
CN5701
VB
21
VG
20
VR
19
24
22
20
IC2101 Y OUT
IC2101 C OUT
EVF VCO
24578
10 11 13
42 44 45
47 48 50
51 53
6
7
8
10
9
XTG SO
45
1
42
TIMING
48 GENERATOR 46
(1/2)
14
ı
18
20
ı
24
2
9 4
CN5806
(1/2)
CN5203 (1/2) CN5202 (1/2)
PANEL B
40
6
PANEL G
42
7
PANEL R
44
8
47
10
9
46
46
47
48
BL ON
EVF G
VSP SO, XVSP SCK
IC5702
CN5201 (1/2)
5
133
132
129
PANEL B
PANEL G
PANEL R
CK-116 BOARD (1/2)
47
79
200 202
204 206
208 212
214 216
135
134
127
PD-168 BOARD (1/2)
1
CPC
2 (FOR CHECK)
4
CN1003 (1/2)
PANEL B
40
PANEL G
42
PANEL R
44
XHD OUT
47
PANEL VG
46
18
22
24
183
184
1
IC2102
6
ı
9
CN1008 (1/3)
EVF VG
4
CPC
EVF VCO
5 (FOR CHECK)
9 11
13 15
OSD HD, OSD VD
ADAI2
ADAO2
SFD BCK
29
ı
32
34
ı
37
42
ı
45
LBUS 0 - 3
51
141
159
ı
161
VSP SO, VSP SI, XVSP SCK
OVERALL (1/4)
(PAGE 3-2)
142
ı
145
CN1005
(3/4)
VD SO, VD SCK
3-2. OVERALL BLOCK DIAGRAM (2/4)
USB D±
MIC901
MICROPHONE L
1
MIC902
MICROPHONE R
1
INT MIC L
35
CN5902
J5901
MIC
(PLUG IN POWER)
CN7204
(1/2)
CN5901
INT MIC R
EXT MIC R
EXT MIC L
1
IC5901
MIC AMP
3
33
36
40
22
14
CN5904
SHOE MIC L
MIC L
MIC R
1
19
3
5
15
17
10
7
IC6301
MAIC GAIN
CONTROL
(3/9)
8
5
3
5
IC6303
AMP
(3/9)
1
7
L
R
58
60
J403
(HEAD PHONE)
46
49
3-4
2
64
HP R OUT
HP L OUT
13
11
HP R
HP L
DCR-TRV940/TRV940E/TRV950/TRV950E
3. BLOCK DIAGRAMS
COVER
3-3. OVERALL BLOCK DIAGRAM (3/4)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-288 BOARD (3/4)
J MECHA DECK
CN1008 (2/3)
RF MON
20
CPC
SWP
(FOR CHECK) 17
RECCK
RECDT
RECCK
RECDT
40
42
CN1901
IC1902
ADDT 0 - 5
ADDT 0 - 5
PBCK
PBCK
SWP
SWP
15
ı
20
13
31
REC/PB AMP
(9/17)
IC1901
34
EQ,
A/D CONV.,
PLL
(9/17)
42
6
7
ODD
5
6
1
2
EVEN
2
3
DRUM
27
22 24
OVERALL (2/4)
(PAGE 3-3)
4
VSP SO, XVSP SCK
111
164
190
32
33
45
ı
52
MC BUS (10)
CAP FG
CAP ON, CAP FWD
165
166
FRRV, TRRV, TRRT
84
178
179
IC2501
(2/2)
VSP SO, VSP SI, XVSP SCK
67
69
70
MECHA
CONTROL
(13/17)
EEPROM
(13/17)
IC2401 (1/2)
4
CAPSTAN
FG AMP
IC2401
(2/2)
DB-014 BOARD (3/5)
CN1001
(3/6)
(12/17)
89
CAP PWM
43
41
CAP ERR0R
CN7206
(3/6)
6
95
CN7206
(4/6)
Q8008, 8020
72
88
DRUM PWM
44
26
IC8000
(1/2)
(RABI)
LPF
2
ı
4
1
80
45
DRUM ERR0R
5
96
78
PWM
DRIVE
(9/9)
SWITCHING
REG.
97
99
4
2
CAP VS
VD SO, VD SCK
2
VD SO, VD SI, VD SCK
80
82
83
198
M902
22
25
1
ı
4
11
ı
14
17
ı
20
CAP U, V, W
CAPSTAN FG
CAPSTAN
MOTOR
M
75
77
M901
27
Q8009, 8021
24
SWITCHING
REG.
DRUM
MOTOR
CN1022
98
100
3
1
DRUM VS
64
67
DRUM
MOTOR
DRIVE
63
65
68
DRUM U, V, W
193
196
195
PD OUT
7
DRUM FG
5
ı
10
M
DRUM PG
DRUM FG SENS
2
DRUM FG
1
DRUM PG
M
53
DRUM
FG AMP
52
50
DRUM
PG AMP
49
LODING MOTOR
DRIVE
69
72
LM±
1
ı
4
26
27
T REEL±
20
21
22
23
S REEL±
23
24
DRUM PG SENS
CN1006
SPCK
192
LD ON, SENS ON
HI SO, HI SI, XHI SCK
LOAD, UNLOAD
TREEL FG
SREEL FG
TAPE END
TAPE TOP
32
33
29
25
REEL
FG AMP
21
TAPE END
DETECT
20
19
TAPE TOP
DETECT
20
TAPE END C
25
TAPE TOP C
27
133
186
176
180
119
OVERALL (4/4)
(PAGE 3-8)
74
76
78
FG 1, 2
VSP SO, XVSP
SCK
VSP SCK
13
15
OVERALL (4/4)
(PAGE 3-8)
7
8
6
197
OVERALL (1/4)
(PAGE 3-2)
SPCK
CAPSTAN
MOTOR
DRIVE
CN1001
(4/6)
25
OVERALL (2/4)
(PAGE 3-3)
35
(12/17)
CN1007
ATF ERR
IC2502
36
38
63
65
66
106
ı
108
TAPE LED ON
H902
T REEL
SENSOR
M903
LOADING
MOTOR
H901
S REEL
SENSOR
Q901
TAPE END
SENSOR
D901
TAPE LED
Q902TAPE TOP
SENSOR
10
DEW AD
DEW
SENSOR
5
S902
MODE
SWITCH
7
ı
9
MODE SW A - C
8
REC PROOF
REC PROOF
S901
15
16
17
CHIME SDA, CHIME SCK
XCC DOWN
11
S903
CC DOWN
05
3-5
3-6
CN901
CASSETTE
MEMORY
DCR-TRV940/TRV940E/TRV950/TRV950E
3. BLOCK DIAGRAMS
COVER
3-4. OVERALL BLOCK DIAGRAM (4/4)
MA-410 BOARD
(3/4)
REMOTE
4
COMMANDER
RECEIVER
CN5906
(2/3)
CN5905
(2/2)
S601 - 604
FOCUS(INFINITY/MAN/AUTO),
PUSH AUTO, FLASH, FADER
5
D601
(FLASH)
Q601
LED DRIVE
12
D603
(CAMERA RECORDING)
13
KEY AD1
6
21
Q5904 - 5906
LED DRIVE
2
13
2
32
29
5
33
60
XSIRCS IN
41
SIRCS PWM
29
51
16
XF TALLY LED
1
28
45
SCHARG LED
CK-116 BOARD (2/2)
S5206 - 5209, 5211, 5212
CN5206
S001
PANEL
OPEN
4
STOP, REW, PLAY, FF, REC
S002
PANEL
REVERSE
3
S5213 - 5217
COLOR BAR, VOL±, DISPLAY/
TOUCH PANEL, AUDIO DUB
CN5203
(2/2)
S5210, 5218 - 5220
PAUSE, BACK LIGHT,
SPOT LIGHT, CUSTOM PRESET
CONTROL SWITCH
BLOCK (KP-1870)
4
S007
EXEC (PUSH)/
SEL
8
5
6
13
17
17
15
3
11
12
11
12
10
10
5
5
HI CONTROL
(5/17)
67
DIAL A
DIAL B
192
79
80
XRESET
7 VIN
CN5201
(2/2)
Q1001 - 1003
36
ı
33
36
ı
33
17
ı
19
49
18
216
36
20
61
RESET
VRO
VOUT
CS
5
8
6
4
EVER 3.0V
VOUT
BATT IN
INITIAL RESET, BACK UP VCC
(15/17)
TOUCH
PANEL I/F
51
30
43
41
38
40
8
73
PLUNGER
STROBO ON
STROBO DOWN
SHOE CONT AD
69
31
39
40
LANC IN, LANC OUT
10
12
34
48
71
72
IC2703
LANC DRIVER
(15/17)
11
CN1001 (6/6)
LANC SIG
Q2909
LED DRIVE
35
19
20
19
20
13
21
13
21
13
VTR DD ON
9
11
7
4
62
39
58
54
52
43
47
49
69
32
56
45
71
30
HS TXD, HS RXD, HS SCK
LANC SIG
XBT LED
14
16
18
8
10
12
19
13
21
D001
(BLUETOOTH)
BT ON
67
75
14
6
1
80
BATT UNREG
62
64
17
19
VTR UNREG
79
2
CN7206 (5/6)
TRV950/TRV950E
Q8003,
Q8004
CN7202
+
6
S
5
–
1
+
CONTROL SWITCH BLOCK
S002-004
(PS-1870)
ACV UNREG
DC IN
2
–
Q8000,
Q8001
82
74
87
84
14
17
XS/S SW
XEJECT SW
4
5
6
POWER
VCR/OFF (CHG)/CAMERA/
MEMORY/NETWORK
3
1
S001
START/STOP
11 21 22
CONTROL SWITCH BLOCK
(CF-1870)
CN7200
CAM DD ON
XSYS RST
STROBO ON
OVERALL (1/4)
(PAGE 3-2)
VTR DD ON
IC8000
(2/2)
MT 4.9V
D 2.8V
D 3.1V
D 1.5V
D 1.9V
A 2.8V
CAM 2.8V
CAM 3.6V
A 4.6V
CAM 15V
CAM –7.5V
SW 15V
RP 4.6V
RP 2.8V
AU 2.8V
PANEL/EVF 2.8V
PANEL/EVF 13.5V
PANEL/EVF 4.6V
3
ZOOM VR AD
STROBO AIN
LD EVR
88
91
13
10
76
25
XPHOTO REC
6
5
XPHOTO FREEZE
ZOOM VR AD
PHOTO
(FREEZE, REC)
OVERALL (3/4)
(PAGE 3-5)
OSD SO, OSD SCK
EVF TALLY
5
7
LD ON, SENS ON
PD OUT
OVERALL (2/4)
(PAGE 3-3)
SENS ON
9
Q4301, 4302
MT 4.9V
IC4301
11
23
28
6
PHOTO TR OUT
Q5903
PHOTO
SENSOR
SWITCH
CN5903
PHOTO TR C
FP-500 FLEXIBLE
BOARD
4
NOT CONNECT
PHOTO TR E
5
AF LASER
MULTI VIBRATOR
(15/17)
1
5
D 2.8V
25
CN5906 (3/3)
SENS ON
2
3-8
29
5
27
7
LD EVR
SAFE ON
PD OUT
IC5902
Q5901, 5902
AF LASER
CONTROL
S001
W-T
(ZOOM) RV001
2
MA-410 BOARD (4/4)
CN1021
(3/3)
05
3-7
16
15
12
S005
EJECT
FAST CHARGE, VTR DD ON
DC/DC CONTROL
(9/9)
3
3
4
6
47
85
86
89
INIT CHARGE ON
INIT CHARGE ON
4
2
1
7
43
42
74
BATT UNREG
FAST CHARGE
XCAM MODE SW, XVTR MODE SW,
PHOTO STBY
CN1001 (5/6)
19
27
BT901
BATTERY
TERMINAL
Q3101
BATTERY CHARGE
DETECTOR
S001
NET WORK
26
FP-497 FLEXIBLE BOARD (2/2)
LD ON
BATT SIG
BATT/XEXT
CN1002 (2/3)
INTELLIGENT
ACCESSORY
SHOE
(2/2)
CN7206 (6/6)
CN7201
CN7207 (2/3)
FLASH
UNIT
15
17
FAST CHARGE
37
INIT CHARGE ON
38
CN1005 (4/4)
DB-014 BOARD (4/5)
5
18
CN7205 (2/2)
JK-222 BOARD (5/5)
LANC SIG
BLUETOOTH
UNIT
64k EEPROM
(5/17)
95
35
SHOE ID 1, 2
57
58
2 PREEND
3 VBAT
VTR UNREG
BATT UNREG
6
5
4
IC2901
2
8
9
CN7207 (3/3)
CN1010
SCHARGE ON
32
5
XSCHARGE FULL
63
18
221
ı
223
IC2702
J402
LANC
EEP TXD3, EEP RXD3, EEP SCK3
73
D2701
10
11
12
DB-014 BOARD (5/5)
61
KEY AD 5
BATT LI 3V
BT-003 BOARD
CN1023
BT RTS, BT RXDT, BT TXDT
68
KEY AD 2
14
PD-168 BOARD (2/2)
CN5802
CN5803
(2/2)
2
17
3 TP TOP, TP BOT, TP L, TP R
ı
5
19
6
TRV950/TRV950E
HI SO, HI SI, XHI SCK
196
195
193
205
ı
207
D2702
BT5201
LITHIUM
BATTERY
TA901
TOUCH
PANEL
IC2905
(2/2)
OVERALL (3/4)
(PAGE 3-5)
66
KEY AD 6
S5201
AUTO LOCK
2
185
190
191
199
ı
201
65
KEY AD 4
15
14
S002 - 006
TXD0, RXD0, SCK0
HI CONTROL
(14/17)
KEY AD 3
CHIME SDA, CHIME SCK
160
162
168
S5221
RESET
AUDIO LEVEL,
EXPOSURE, WHT BAL,
SHUTTER SPEED,
PROGRAME AE
13
8
X3102
32.768kHz
23
ı
25
REC PROOF
37
CN1002 (3/3)
S5202 - 5205
DATA CODE, EDIT SEARCH±,
ZEBRA (OFF/70%/100%)
CN5205
S001
MENU
16
X3101
10MHz
52
10
CN1003 (2/2)
16
XCC DOWN
5
IC3101
FP-495 FLEXIBLE
BOARD
CPC
(FOR CHECK)
CN1021 (2/3)
28
3
D602
(IR)
CN1008 (3/3)
HI XRESET
16
XINIT
9
VC-288 BOARD (4/4)
HS TXD, HS RXD, HS SCK
FP-504 FLEXIBLE BOARD (2/2)
IC601
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LD EVR
PD OUT
1
2
D501
(LASER UNIT)
DCR-TRV940/TRV940E/TRV950/TRV950E
3. BLOCK DIAGRAMS
COVER
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-5. POWER BLOCK DIAGRAM (1/3)
DB-014 BOARD (1/2)
F8007
ST-UNREG
F8006
PRT UNREG
F8005
SHOE UNREG
F8004
Q8005 - 8007
Q8017, 8018, 8028
F8003
VTR UNREG
F8002
IC8000
BT901
BATTERY
TERMINAL
CN7202
+
2
FAST CHARGE
–
3
INIT CHARGE ON
+
6
S
5
–
1
16 Vcc(O)-2
20 Vcc(O)-3
42 Vcc(O)-1
L8002
CAP VS
L8003
DRUM VS
SWITCHING
F8001
Q8000, 8001
4
DC IN
Q8008, 8020
DC/DC CONTROL
(9/9)
OUT7-P 26
OUT7-N 27
V-IN7 51
Q8009, 8022
SWITCHING
7 RT
6 CT
F8000
Q8003, 8004
CHARGE CONTROL
OUT8-P 24
OUT8-N 25
V-IN8 49
Q8013, 8022
L8007
L8010
MT 4.9V
D8003
L8025
CAM 15V
L8015
PANEL/EVF 2.8V
L8023
RP 2.8V
SWITCHING
BATT/XEXT
BATT SIG
OUT6-P 28
OUT6-N 29
V-IN6 50
L8001
BATT UNREG
CN7207 (1/3)
79 75 67
OUT9-N 23
–IN9 80
–IN(S)9 1
1
2 6 14
VC-288 BOARD
(1/2)
Vdd(O)-3 19
Vdd(O)-1 41
80
OUT4-P 30
OUT4-N 31
V-IN4 53
HI CONTROL
(14/17)
INIT CHARGE ON
BATT/XEXT
Q3101
BATTERY
CHARGE
DETECTOR
IC2702
INITIAL RESET,
BACK UP VCC
(15/17)
CK-116 BOARD
(1/2)
CN5203 (1/2)
7 VIN
CN1003 (1/2)
5
BATT LI 3V
5
VOUT 6
3 VBAT
2 PREEND VRO 8
BT5201
LITHIUM
BATTERY
FAST CHARGE 37
38 INIT CHARGE
74 BATT/XEXT
OUT1-P 36
OUT1-N 37
V-IN1 55
CN7206
(1/2)
CN1001 (1/2)
D2701
A 2.8V
L8017
D 2.8V
74
27
Q8012, 8024
L8006
82
72
95
94
35
49
20
21
19
29
6
7
CN1002 (2/3)
SHOE ON 17
XLANC ON 46
EVER 3.0V
Q8016, 8027
L8009
OUT5-P 38
OUT5-N 39
V-IN5 52
57
44
45
46
CTL
LD
DIN
CLK
L8014
D 1.5V
L8021
PANEL 4.6V
L8020
RP 4.6V
Q8015(2/2)
70
AU 4.6V
L8024
EVF 4.6V
47 RST
56 Vdd
75 GCTL
OUT10-P
–IN(A)10
–OUT(A)10
–IN10
–IN(S)10
22
4
5
3
10
D2702
Q8029 - 8031
CN1005 (1/2)
LANC DC
OUT2-P
OUT2-N
-IN2
+IN2
Q2701
14 LANC DC
14
CAM –7.5V
SHOE ON
L8012
CAM 2.9V
IC3406
34
35
60
61
3.1V REG.
(1/9)
Q8011, 8023
L8005
5 STB
2 VIN
L8013
5
4
(9/9)
1
5 STB
2 VIN
VOUT 3
CAM 3.1V
CAM 3.6V
D 2.9V
VOUT 3
IC8002
2.9V REG.
(9/9)
05
3-9
EVF 13.5V
IC8004
L8008
IC8001
EVER 3.0V
PANEL 13.5V
L8028
–7.5V/13.5V REG.
(9/9)
SWITCHING
OUT3-P 32
OUT3-N 33
V-IN3 54
C
L8027
REG1 8
SWITCHING
POWER (3/3)
(PAGE 3-14)
PANEL –15.3V
STB 1
7 VCC
Q8004
EMERGENCY
DETECT
IC2703
LANC DRIVER
(15/17)
L8026
REG3 4
3 VEE
Q8010, 8022
JK-222 BOARD
(1/3)
D 3.1V
L8000
46
11
A 4.6V
L8016
SWITCHING
CN7207 (2/3)
35
L8018
3.1V
REG
Q8015(1/2)
VB 14
J402
LANC
D 1.9V
SWITCHING
43 IB SI
42 IB SO
VTR DD ON
XCS DD
HI EVER SO
HI EVER SC
AU 2.8V
Q8032 - 8034
1.9V
REG
SWITCHING
54 BATT SENSE
55 ACV SENSE
56 VTR DD SENSE
VTR UNREG
D 2.8V
BATT SIG
L8008
L8019
CN1002 (1/3)
B
Q8014, 8026
L8022
SWITCHING
IC3101
POWER (3/3)
(PAGE 3-13)
Q8026
SWITCHING
3-10
A
POWER (2/3)
(PAGE 3-11)
DCR-TRV940/TRV940E/TRV950/TRV950E
3. BLOCK DIAGRAMS
COVER
3-6. POWER BLOCK DIAGRAM (2/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN7205 (2/2)
DB-014 BOARD (2/2)
CAP VS
CAP VS 22
23
DRUM VS 24
25
DRUM VS
CN7207 (3/3)
PANEL 13.5V
5
PANEL 4.6V
9
PANEL –15.3V
7
RP 4.6V
10
RP 2.8V
12
D 1.9V
41
PANEL 13.5V
PANEL 4.6V
PANEL –15.3V
RP 4.6V
RP 2.8V
D 1.9V
D 1.5V
D 1.5V
CAM 2.9V 31
33
CAM 3.6V
19
D 2.9V
24
D 3.1V
27
A 4.6V
25
CAM –7.5V
21
CAM 15V
23
A 2.8V
35
PANEL/EVF 2.8V
3
MT 4.9V 54
56
EVF 13.5V
44
AU 2.8V
29
PANEL UNREG 58
60
CAM 2.9V
CAM 3.6V
D 2.9V
D 3.1V
A 4.6V
CAM –7.5V
CAM 15V
A 2.8V
PANEL/EVF 2.8V
MT 4.9V
EVF 13.5V
AU 2.8V
D 2.8V 14
16
VAP DD ON
77
ZM RST LED
48
D 2.8V
VAP DD ON
L3401
MT 4.9V
ZM RST LED
IC3402
FOCUS/ZOOM/
IRIS/ND FILTER
DRIVE
(1/9)
A 2.8V
D 2.8V
POWER (1/3)
(PAGE 3-10)
D
POWER (3/3)
(PAGE 3-13)
VTR UNREG 62
64
VTR UNREG
A
18
20
22
L3402
F MR VCC
L3403
IC3404
IC3401
IC3403
FOCUS/ZOOM
CONTROL
(1/9)
IRIS CONTROL,
HALL/REF AMP
(1/9)
HALL BIAS CONTROL,
HALL AMP
(1/9)
CAM 3.1V
CAM 3.1V
IC1501
VAP YAW
DRIVER
(2/9)
Q1503, 1504
MT 4.9V
D 2.8V
FB7000
L7004
IC7000
IC1503
VIDEO
IN/OUT
(6/9)
YAW/PITCH/
REF AMP
(2/9)
PANEL/EVF 2.8V
L4201
EVF 13.5V
L4203
9
ZOOM
MR
IC3405
LB-080 BOARD
CN7211
EVF 13.5V
1
CN6102
VDD
20
RGT, DWN
EVF 4.6V
IC1502
20
LCD903
1
COLOR
EVF
UNIT
7
8
D6101
(TALLY)
1
D6102
(BACK LIGHT)
MA-410 BOARD (1/2)
INVERTER
(2/9)
JK-222 BOARD (2/3)
CN7204
CN1501
A 4.6V
AU 2.8V 20
21
ACTIVE
LENS
ACTUATOR
7
AU 2.8V
7
8
CN5904
L5901
IC5901
MIC
AMP
IC6303
L6002
L6001
IC6001
AUDIO
IN/OUT
(4/9)
AUDIO
A/D CONV.,
D/A CONV,
(4/9)
AMP
(3/9)
FP-497 FLEXIBLE BOARD
TRV950/TRV950E
IC6301
DOO1
(BLUETOOTH)
MIC GAIN
CONTROL
(3/9)
CN7205
BT LED A
CN1010
MT 4.9V
11
12
11
12
ST UNREG
6
9
6
9
EVF 13.5V
EVF 4.6V
AU 2.8V
VTTR UNREG
EVF 13.5V
EVF 4.6V
AU 2.8V
VTTR UNREG
PRT UNREG
SHOE UNREG
D 2.8V
PRT UNREG
SHOE UNREG
D 2.8V
FLASH
UNIT
20
PRT HEAD UNREG
22
23
PRT UNREG
SHOE UNREG
24
25
SHOE UNREG
CONTROL SWITCH BLOCK
(CF-1870)
CN7200
D 2.8V
05
3-11
CN6101
IC1505
IC6004
FB6000
PRT UNREG
SHOE UNREG
FOCUS
MR
ND FILTER CONTROL,
HALL BIAS CONTROL,
HALL AMP
(1/9)
TIMING
GENERATOR
(7/9)
IC4201
LCD
DRIVER
(7/9)
Q6007
EVF 4.6V
13
LPF
(2/9)
IC4202
AU 2.8V
ST UNREG
LENS TEMP
SENSOR
IC1506
FB4201
AU 4.6V
MT 4.9V
5
IC1504
AU 4.6V
VTTR UNREG
Z MR VCC
LENS BLOCK
VAP PITCH
DRIVER
(2/9)
Q1501, 1502
AU 4..6V
CN1004
SENS VCC
Q3402
3-12
RV001
W (ZOOM)
4
T
14
15
INTELLIGENT
ACCESSORY
SHOE
DCR-TRV940/TRV940E/TRV950/TRV950E
3. BLOCK DIAGRAMS
COVER
3-7. POWER BLOCK DIAGRAM (3/3)
TRV950/TRV950E
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-288 BOARD (2/2)
CK-116 BOARD (2/2)
BT-003 BOARD
BLUETOOTH
UNIT
10
6
POWER (1/3)
(PAGE 3-9)
CN1023
PANEL 4.6V
C
CN1003 (2/2)
EVER 3.0V
48
48
54
54
56
56
CN5203 (2/2)
EVER 3.0V
CAP VS
1
3
DRUM VS
60
VTR UNREG
D 2.8V
B
PANEL UNREG
17
19
VTR UNREG
40
71
69
DRUM/CAPSTAN/
LOADING
DRIVE
(12/17)
L2401
EVF 13.5V
L2105
IC2102
FB2103
DV I/F
(7/17)
FB1901
L2103
L2104
IC1901
IC2101
FB2501
DV SIGNAL
PROCESS
(7/17)
48
50
60
58
FB2502, 2503
L1903
REC/PB
AMP
(9/17)
8
D 1.5V
PANEL –15.3V
FB2001
IC2001
L2002
VIDEO
A/D CONV.
(11/17)
PANEL UNREG
IC2302
FB2303
D 1.5V
D 2.8V
D 3.1V
12
FB1602
FB2302
IC2301
FB2301
USB I/F
(10/17)
FB1351
D 2.8V
CN4005
L4000
CAM 3.6V
CAM 2.9V
CAM 2.9V
CAM –7.5V
CAM –7.5V
L1301 - 1303
IC1302
CAM 3.6V
L1303
2 Vi
Vo 3
CN1021
A 4.6V
A 2.8V
CN5906
10
24
21
22
21
22
7
27
FP-504 FLEXIBLE BOARD
IC601
CN5905
A 4.6V
MT 4.9V
A 2.8V
REMOTE
COMMANDER
RECEIVER
4
F601
6
D602
(IR)
14
D601
(FLASH)
IC1301
CAMERA RGB
PROCESSOR
(2/17)
CD-389 BOARD
2.5V REG
(2/17)
CN1201
CAM 2.9V
D 1.5V
D 2.8V
IC1201
OSC CONTROL
(5/17)
FB1203
L1501 FB1207
16M bit
FLASH MEMORY
(6/17)
FB2903
FB1213
34 34
37 37
L1204
D 3.1V
D 1.5V
L2901
FB2902
Q2905, 2906
FB2905
FB2904
MS VCC ON
L105
IC105
IC1202
L1211 FB1211
IC1204
L1205
AGC, A/D CONV.
(R)
(1/17)
CAM 3.6V
IC2901
IC2903
IC2904
64k EEPROM
(5/17)
BUFFER
(5/17)
XTAL OSC
(5/17)
S/H
(B)
IC100
L103
CCD IMAGER
(R)
33 33
L102
IC104
L1209
L104
CCD IMAGER
(G)
15 15
J MECHA DECK
IC1205
AGC, A/D CONV.
(G)
(1/17)
CN1006
MT 4.9V
13
D901
TAPE LED
TAPE LED A
CN901
L1006
CHIME VDD
D 2.8V
19
HALL VCC
CASSETTE
MEMORY
H901
S REEL
SENSOR
Q2401
CHIME PWR CONT
CAM DD ON
IC104
S/H
(G)
H902
T REEL
SENSOR
05
3-13
IC103
S/H
(R)
L1212 FB1212
L1206
IC102
L101
IC2905
HI CONTROL,
DIGITAL STILL CONTROL
(5/17)
CHIME PWR CONT 31
CAM DD ON 168
23 MS VCC ON
L100
CCD IMAGER
(B)
L1208
18
CN1009
D 2.8V
VL
L1207
IC1203
AGC, A/D CONV.
(B)
(1/17)
TIMING
GENERATOR
(1/17)
Q1201, 1202
FP-503 FLEXIBLE
BOARD
CN100
CAM 2.9V
43 43
IC3002
FB3001
CN1008
D 2.8V
SE4002
MANUAL
FOCUS
SENSOR
Q1201, 1202
16M bit
SDRAM
(6/17)
L1701
YAW
SENSOR
D603
(CAMERA RECORDING)
CAM –7.5V
IC3001
FB1701
SE4001
PITCH/YAW
SENSOR AMP
IC1351
CAM 15V
CAM 15V
MPEG MOVIE/
DIGITAL STILL
PROCESS
(4/17)
PITCH
SENSOR
IC4001
1
SDRAM
(2/17)
L1304 FB1303
FB1702
CN5805
12
JK-222 BOARD(3/3)
3-14E
4
23
LCD901
COLOR
LCD UNIT
3
ND901
(BACK LIGHT)
Q8501, 8502
IC1601
CAMERA
PROCESSOR
(3/17)
D 2.9V
MS VCC
IC5702
BL ON
4
TIMING
GENERATOR
(1/2)
FB1604
IC1704
2
VGL
MA-410 BOARD
(2/2)
MT 4.9V
A 2.8V
A 2.8V
D 2.8V
AUDIO
A/D CONV.
(10/27)
CN5701
VSH
24
VGH
1
7
L5801
27
MT 4.9V
L1201 FB1201
10
LCD DRIVER
(1/2)
D 2.8V
A 4.6
MT 4.9V
16M bit
SDRAM
(4/17)
MEMORY
STICK
IC5701
L5704
8
7
CN1005 (2/2)
IC2502
D 1.5V
D 2.8V
IC1701
D001
(MS ACCESS)
L5703
XREEL HALL ON 153
L1210 FB1210
3
52
50
CAMERA/
MECHA
CONTROL
(13/17)
FB2104
R1211
CPC
(FOR CHECK)
6
IC1902
A 4.6
AU 2.8V
62
58
52
50
EEPROM
(13/17)
52
57
6
L5701
SE-132 BOARD
FB2102
RP 4.6V
RP 2.8V
FB1601
54
PANEL 4.6V
IC2501
POWER (2/3)
(PAGE 3-12)
65
67
PANEL 13.3V
CN5802
FB2101
EQ, A/D CONV.,
PLL
(9/17)
46
5
170 VAP DD ON
55 ZM RST LED
D 1.9V
L1901
25
27
5
LCD DRIVER
(2/2)
L5702
PANEL UNREG
D
56
PANEL 2.8V
IC5801
R5801
PANEL/EVF 2.8V
PANEL 13.5V
PANEL 4.6V
PANEL –15.3V
L1902
59
61
63
60
58
VAP DD ON
ZM RST LED
IC2401
37
5
VDD
PANEL/EVF 2.8V
PANEL 13.5V
PANEL 4.6V
PANEL –15.3V
21
23
5
POWER (1/3)
(PAGE 3-9)
CN1002 (3/3)
VAP DD ON
4
ZM RST LED
33
78
76
72
74
CN5806
CN5201
CN1001 (2/2)
4
5
PD-168 BOARD
CN5202
PH601, 602
INVERTER
2 TRANSFORMER
UNIT
BACK LIGHT
5
DRIVE
J
LENS
BLOCK
K
4-1
I
CD-389 BOARD
CN100 60P
CN1201
V1B
42
41
V2B
CSUB
40
39
CLPDM
VL
V1R
38
37
35
V2R
V3R
36
33
VDD_R
CAM_2.9V
31
V4R
29
XSHDR
27
B_GND
60
59
B_GND
60P
B_GND
60
H2B
SHTB
58
57
H2B
SHTB
58
H1B
B_GND
56
55
H1B
B_GND
56
B_GND
RGB
54
53
B_GND
RGB
54
51
CCD+B
B_GND
52
51
CCD+B
B_GND
52
49
B_GND
CCD-B
50
49
B_GND
CCD-B
50
47
XSHDB
B_GND
48
47
XSHDB
B_GND
48
45
V4B
XSHPB
46
45
V4B
XSHPB
46
43
VDD_B
V3B
44
43
VDD_B
V3B
44
41
V2B
39
CLPDM
V1B
42
CSUB
37
40
VL
V1R
38
35
V2R
V3R
36
34
33
VDD_R
CAM_2.9V
34
XSHPR
32
31
V4R
XSHPR
32
SHTR
30
29
XSHDR
SHTR
30
R_GND
H2R
28
27
R_GND
H2R
28
25
RGR
H1R
26
25
RGR
H1R
26
23
R_GND
R_GND
24
23
R_GND
R_GND
24
21
CCD+R
CCD-R
22
21
CCD+R
CCD-R
22
19
R_GND
R_GND
20
19
R_GND
R_GND
20
17
V4G
V3G
18
17
V4G
V3G
18
15
VDD_G
13
V1G
11
XSHDG
9
G_GND
7
RGG
5
G_GND
3
CCD+G
1
G_GND
V2G
16
15
VDD_G
XSHPG
14
13
V1G
SHTG
12
11
XSHDG
H2G
10
9
G_GND
H1G
8
7
RGG
G_GND
6
5
G_GND
CCD-G
4
3
CCD+G
CCD-G
4
G_GND
2
1
G_GND
G_GND
2
V2G
16
XSHPG
14
SHTG
12
H2G
10
H1G
8
G_GND
6
7
9
11
ND_HALL_AD
I_HALL_AD
PITCH_POS_AD
YAW_POS_AD
SHOE_CONT_AD
REG_GND
REG_GND
BATT_SIG
DIRA1
8
10
12
14
16
4-2
19
VTR_UNREG
PANEL_UNREG
PANEL_UNREG
Z_MRB_REF
Z_MRA_REF
20
22
24
41
43
45
47
57
59
MT_GND
ZM_RST_LED
SHOE_ON
EVF_13.5V
SHOE_ID2
SHOE_ID1
EN1
DIRB1
SCHARGE_ON
STROBO_ON
D_2.9V
D_1.5V
D_1.5V
D_1.5V
D_2.8V
D_2.8V
ND_HALL_OFFSET
ND_HALL_GAIN
I_HALL_OFFSET
I_HALL_GAIN
D_1.9V
PANEL_GND
PANEL_GND
A_2.8V
CAM_2.9V
CAM_2.9V
AU_2.8V
USB_3.1V
A_4.6V
CAM_15V
CAM_-7.5V
CAM_3.6V
REG_GND
F_MRB_REF
F_MRA_REF
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
PR_2.8V
RP_4.6V
REG_GND
REG_GND
REG_GND
REG_GND
EVER_3.0V
PANEL_4.6V
PANEL_-15.3V
PANEL_13.5V
PANEL/EVF_2.8V
BATT_UNREG
70
72
74
76
78
80
79
77
75
1
3
5
7
9
11
13
15
17
19
BATT_UNREG
PANEL/EVF_2.8V
PANEL_13.5V
PANEL_-15.3V
PANEL_4.6V
EVER_3.0V
F_MRA_REF
F_MRB_REF
REG_GND
CAM_3.6V
CAM_-7.5V
CAM_15V
A_4.6V
USB_3.1V
REG_GND
REG_GND
REG_GND
REG_GND
RP_4.6V
PR_2.8V
D_2.8V
D_2.8V
D_1.5V
D_1.5V
D_1.5V
D_2.9V
IRIS_COM
SHUTTER_ON
STROBO_ON
SCHARGE_ON
DIRB1
EN1
SHOE_ID1
SHOE_ID2
XIC3404_RST
EVF_13.5V
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
ST_GND
REG_GND
REG_GND
STROBO_DOWN
PLUNGER
PLUNGER
XSCHARGE_FULL
MT_GND
MT_GND
MT_GND
MT_GND
STROBO_ON
MT_4.9V
MT_4.9V
N.C
ST_UNREG
ST_UNREG
ST_UNREG
ST_UNREG
SCHARGE_ON
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
17
73
71
69
67
65
63
61
21
23
25
27
AU_2.8V
CAM_2.9V
CAM_2.9V
A_2.8V
PANEL_GND
PANEL_GND
D_1.9V
I_HALL_GAIN
46
ST_GND
16
55
53
29
31
33
35
37
39
41
43
SHOE_ON
48
1
4-3. PRINTED WIRING BOARDS
IRIS_COM
SHUTTER_ON
ND_HALL_GAIN
47
23P
ST_GND
ST_GND
CN1010
FP-497 FLEXIBLE
51
MT_GND
ND_HALL_OFFSET
49
I_HALL_OFFSET
52
MT_GND
HALL_REF
51
45
54
MT_4.9V
53
ZM_RST_LED
56
MT_4.9V
REG_GND
REG_GND
55
50
58
PANEL_UNREG
6
5
4
BT901
BATTERY TERMINAL
49
39
37
35
33
Z_MRA_REF
57
BATT_UNREG
BATT_SIG
15
XIC3404_RST
29
MT_GND
HALL_REF
30
31
27
MT_4.9V
REG_GND
28
25
MT_4.9V
REG_GND
26
62
PANEL_UNREG
Z_MRB_REF
59
60
64
VTR_UNREG
VTR_UNREG
XSCHARGE_FULL
STROBE_PLUNGER
61
66
68
63
REG_GND
YAW_POS_AD
BATT_SIG
DIRA1
70
PITCH_POS_AD
REG_GND
69
65
72
I_HALL_AD
REG_GND
71
67
74
ND_HALL_AD
SHOE_CONT_AD
73
3
2
14
23
21
17
VTR_UNREG
XSCHARGE_FULL
STROBE_PLUNGER
18
15
76
CAM_DD_ON
BATT/XEXT
75
ACV_UNREG
ACV_GND
BATT_XEXT
BATT_GND
1
6
6P
5
XPHOTO_STBY
CN7202
4
CONTROL
SWITCH
BLOCK
(PS-1870)
13
5
CAM_DD_ON
BATT/XEXT
80
78
VAP_DD_ON
77
IRIS_PWM
ND_PWM
INIT_CHARGE_ON
79
80P
3
XCAM_MODE_SW
2
XS/S_SW
XVTR_MODE_SW
1
GND
6P
XEJECT_SW
CN7201
13
REG_GND
3
1
ND_PWM
IRIS_PWM
CN7207
ND_DRIVE+
39
25
27
24
SHOE_UNREG
26
23
SHOE_UNREG
Note: Although parts are mounted on the board,
they are not used in TRV940/TRV940E.
80P
NC
NC
38
ND_BIAS+
37
ND_HALL+
ND_HALL34
36
33
35
NC
ND_BIAS-
32
ND_DRIVE-
IG_DRIVE+
29
NC
IG_DRIVE28
22
PRT_HEAD_UNREG
S001
NETWORK
6
53
BT_ON
21
PRT_HEAD_UNREG
FRAME SCHEMATIC DIAGRAM (1/3)
VAP_DD_ON
55
12
4
57
11
INIT_CHARGE_ON
B_GND
REG_GND
20
BT_LED_K
10
2
59
31
NC
27
19
9
30
NC
26
18
17
BT_LED_A
16
SHOE_ID1
TXD
15
RXD
LANC_SIG
14
RTS(SCK)
SHOE_ID2
12
13
CTS(HDS)
11
SHOE_MIC_GND
STBY_ON/SHOE_MIC_R
9
10
SHOE_MIC_GND
8
SHOE_MIC_GND
7
5
6
4
SHOE_MT_GND
SHOE_MIC_GND
3
SHOE_MIC_L
2
SHOE_MT_GND
SHOE_CONT_AD
1
SHOE_UNREG_GND
27P
SHOE_UNREG_GND
CN7205
SHOE_UNREG_GND
4-2. SCHEMATIC DIAGRAMS
CN1002
H
IG_HALL-
EVF_VCC
25
1
IG_BIAS-
20
24
EVF_GND
EVF_VCC
IG_HALL+
2
IG_BIAS+
19
23
VST
EVF_GND
8
22
3
NC
VCK
18
21
17
VST
NC
STB
VCK
4
20
5
FOCUS+
16
FOCUS-
STB
19
VDD
18
EN
1
NC
6
17
15
F_MR_A
EN
F_MR_B
VSS
F_MR_GND
HST
2
16
7
15
14
14
13
HST
Z_MR_A
HCK2
VST
F_MR_VCC
VCK
3
13
LB-080
BOARD
4
7
12
12
Z_MR_GND
HCK1
Z_MR_B
STB
11
5
10
11
Z_MR_VCC
HCK2
BLK
9
HCK1
8
EN
ZOOM_RST
BLK
9
LED_ON/OFF
8
VB
10
6
GND
TEMP_OUT
VR
11
8
GND
8
SENS_GND
VG
12
10
XPHOTO_REC
7
7
13
9
VB
6
6
COM
VG
XPHOTO_FREEZE
6
SENS_VCC
14
VR
D_2.8V
5
5
7
HST
N.C.
4
ZOOM_A
COM
RGT
3
4
HCK2
8P
ZOOM_B-
EVF_GND
10
DWN
ZOOM_VR_AD
ZOOM_B
15
7
GND
2
3
6
8
1
2
EVF_GND
LED_DA
39P
B
ZOOM_A-
HCK1
9
5
CN1004
COVER
1
EVF_GND
11
XEVF_TALLY
18
Y_OUT
16
19
3
GND
5
2
LED_DA
Y_DRIV_B
4
EVF_GND
XTALLY_LED
1
CN7211
2
LED_ON/OFF
BLK
EVF_4.6V
Y_DRIV_A
VB
12
N.C.
20
3
13
17
21
1
20P
GND
VR
EVF_4.6V
4
F
VG
14
CN6101
P_OUT
E
15
16P
A_4.6V
CN6102
5
LCD903
COLOR
EVF UNIT
COM
6
D
16
P_DRIV_A
C
CONTROL
SWITCH
BLOCK
(CF-1870)
7
CN7200
8
10P
G
CN1501
D001
(BLUETOOTH)
P_DRIV_B
INTELLIGENT
ACCESSORY
SHOE
4
NC
TRV950/TRV950E (Note)
3
9
A
2
10
1
FP-547 FLEXIBLE
DCR-TRV940/TRV940E/TRV950/TRV950E
Ver 1.1 2002. 09
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAMS
18
DC IN
FLASH UNIT
FP-493 FLEXIBLE
21P
DB-014 BOARD (1/2)
FP-499 FLEXIBLE
VC-288 BOARD (1/3)
05
FRAME (1/3)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
1
2
3
5
4
6
4-3. PRINTED WIRING BOARDS
9
8
7
10
13
12
11
14
15
16
FRAME SCHEMATIC DIAGRAM (2/3)
A
97
99
CAP_VS
DRUM_VS
100
91
95
DRUM_VS
98
CAP_VS
CAP_ERROR
DRUM_ERROR
96
89
93
EVF_B
EVF_R
REG_GND
92
94
87
IC2101_Y_OUT
90
EVF_G/BW_Y
85
83
REG_GND
88
REG_GND
81
IC2101_C_OUT
86
REG_GND
REG_GND
84
IC2001_APC_ERROR
79
BEEP
82
IC7001_C_OUT
77
VCO
80
REG_GND
75
73
LED_DA
78
REG_GND
PANEL_XVD
76
IC7001_Y_OUT
71
DATA_TO_SFD
74
PANEL_XHD
69
SFD_LRCK
DATA_FROM_SFD
67
63
65
72
SFD_FCK
SFD_BCK
70
XCS_AU1
68
REG_GND
LENS_TEMP_AD
XCS_AU2
66
61
XPWDA
64
IR_L
59
57
XPWAD
62
IR_R
55
XAUDIO_IN
60
REG_GND
SDC_IN
58
AGC_CONT
53
XCS_EVF
56
ACC_CONT
51
XVIDEO_IN
54
XCS_IC7001
47
45
49
RTS(SCK)
DEM0
52
IC7001_CK
DEM1
50
RXD
PITCH_PWM
48
43
YAW_PWM
46
XBT_LED
41
39
TG_VD
44
TXD
37
CAM_SCK
42
CTS(HDS)
CAM_SO
40
STROBO_DOWN
35
CAM_SI
38
VSP_SO
33
31
CAM_CS
36
XVSP_SCK
29
VSS
34
ZM_RST
LANC_SIG
32
XRST_VTR
27
BT_ON
30
XCS_DD
25
VOL_CS
28
FAST_CHARGE
23
21
XLR/INT
ZOOM_VR_AD
19
26
VD_SO
VD_SCK
17
15
13
KASYAON
VTR_DD_ON
XEJECT_SW
XPHOTO_REC
XVTR_MODE_SW
REG_GND
AU_2.8V
24
20
21
22
18
AU_2.8V
VD_SO
MA_GND
SHOEMIC_L
20
MIC_R
19
VD_SCK
16
17
XCAM_MODE_SW
14
MA_GND
XS/S_SW
MA_GND
MIC_L
18
HP_R
15
16
REG_GND
1
13
SP-
12
4
10
A_GND
100P
A_GND
HP_L
REG_GND
C
R_I/O
14
8
9
11
9
V_GND
11
L_I/O
SPCK
6
7
PHOTO_STBY
V_GND
12
V_I/O
7
5
VSS
REG_GND
XPHOTO_FREEZE
4
8
21P
10
2
S_C_GND
CN7204
5
S_Y_GND
S_C_OUT
3
S_Y_OUT
3
STBY_ON
1
REG_GND
HI_EVER_SCK
VAP_DD_ON
7
HI EVER_SO
C_RESET
6
EVF_TALLY
YAW_AD
5
8
REG_GND
4
SP+
3
SE-132
BOARD
6
PITCH_AD
CN7206
B
DB-014 BOARD (2/2)
8P
D_2.8V
2
2
CN4005
1
4
ID
5
GND
CN5906
MF_LED
CN1021
1
33
2
32
MF_A
2
INT_MIC_GND
MF_B
30
4
MF_B
SCHARGE_LED
29
5
SCHARGE_LED
1
INT_MIC_R
2
INT_MIC_GND
2P
CN5902
KEY_AD1M
PD_OUT
3
MTGND
6P
MA-410 BOARD
6
28
27
7
A_2.8V
REG_GND
26
8
REG_GND
SENS_ON
25
9
SENS_ON
A_4.6V
24
10
A_4.6V
PHOTO_TR_OUT
23
11
PHOTO_TR_OUT
PHOTO_TR_C (N.C)
REG_GND
22
12
REG_GND
5
PHOTO_TR_E (N.C)
XSIRCS_IN
21
13
XSIRCS_IN
20
14
AU_GND
CN5905
J
1
D501
(LASER UNIT)
FP-504 FLEXIBLE
L
16P
REG_GND
19
AU_2.8V
18
EXT_MIC_DET
17
REG_GND
16
2
SIRCS_DRV_CL
AU_GND
15
3
X_SIRCS_IN
AU_GND
14
4
A_4.6V
MT_4.9V
5
KEY_AD1M
6
MT_4.9V
7
FP-494 FLEXIBLE
4
N.C.
15
16
AU_2.8V
17
EXT_MIC_DET
18
REG_GND
19
AU_GND
20
AU_GND
13
21
MT_4.9V
MT_4.9V
12
22
MT_4.9V
11
23
REG_GND
MF_B
XMIC_MONO
10
24
XMIC_MONO
8
MF_A
AF_LD_VCC
9
25
AF_LD_VCC
9
GND
AF_LD_VCC
8
26
AF_LD_VCC
10
GND
PD_OUT
7
27
PD_OUT
LD_EVR
6
28
LD_EVR
SCHARGE_LED
SAFE_ON
5
29
SAFE_ON
XTALLY_LED
MT_GND
4
30
MT_GND
MT_GND
3
31
MT_GND
SIRCS_PWM
2
32
SIRCS_PWM
1
33
N.C
MF_LED
12
13
14
A_2.8V
15
MT_GND
16
N.C.
4-3
12
13
REC_CRRT0
14
REG_GND
15
HI_XRESET
16
SWP
17
RF_IN
18
GND
19
RF_MON
20
CPC
(FOR CHECK)
CN1024
6P
4-4
PANEL_VG
1
PANEL_COM
2
GND
3
XHD_OUT
4
N.C
5
N.C
6
CPC
(FOR CHECK)
CAP_ERROR
2
CAP_VS
DRUM_VS
1
11
FRRV
4
CAP_VS
DRUM_VS
3
DRUM_ON
REC_CRRT1
6
DRUM_ERROR
10
8
5
9
XCS_ST_IMAGE_IC
10
7
8
XINIT
EVF_B
9
7
EVF_R
IC2101_Y_OUT
11
6
XCS_MC_FLASH
G
14
REG_GND
REG_GND
13
5
GND
MD2
REG_GND
16
IC2101_C_OUT
15
4
EVF_VCO
12
18
REG_GND
IC2001_APC_ERROR
REG_GND
17
3
EVF_G/BW_Y
20
IC7001_C_OUT
BEEP
19
22
REG_GND
VCO
26
21
IC7001_Y_OUT
24
LED_DA
23
REG_GND
PANEL_XVD
25
28
DATA_TO_SFD
27
PANEL_XHD
SFD_LRCK
29
30
SFD_FCK
SFD_BCK
31
DATA_FROM_SFD
34
XCS_AU1
32
36
REG_GND
LENS_TEMP_AD
IR_L
XPWDA
37
XCS_AU2
IR_R
XPWAD
39
33
REG_GND
XAUDIO_IN
41
35
AGC_CONT
SDC_IN
43
38
ACC_CONT
XCS_EVF
45
40
44
42
XCS_IC7001
XVIDEO_IN
47
46
50
DEM0
49
48
52
RTS(SCK)
IC7001_CK
DEM1
51
RXD
54
PITCH_PWM
53
XBT_LED
56
YAW_PWM
55
TXD
58
TG_VD
57
60
62
CAM_SCK
59
CTS(HDS)
STROBO_DOWN
CAM_SO
61
64
VSP_SO
CAM_SI
63
66
XVSP_SCK
CAM_CS
65
68
70
ZM_RST
XRST_VTR
LANC_SIG
VSS
72
XCS_DD
BT_ON
71
67
74
FAST_CHARGE
VOL_CS
73
69
76
ZOOM_VR_AD
XLR/INT
75
78
VD_SO
KASYAON
77
80
VD_SCK
REG_GND
79
82
VTR_DD_ON
VD_SO
81
84
86
88
XEJECT_SW
XPHOTO_REC
90
92
VSS
SPCK
VC-288 BOARD (2/3)
05
FRAME (2/3)
2
EVF_VG
ZOOM_MIC_CONT
REG_GND
11
1
KEY_AD1M
A_2.8V
AU_GND
N.C
D_2.8V
EVF_LED_DA
MF_LED
3
2
94
33P
XF_TALLY_LED
31
LD_EVR
96
CN1008
20P
MF_A
1
XVTR_MODE_SW
D_2.8V
VD_SCK
PS_OUT
27
XCAM_MODE_SW
YS_OUT
26
XS/S_SW
C_RESET
25
83
REG_GND
24
85
VAP_DD_ON
23
STBY_ON
REG_GND
22
HI_EVER_SCK
REG_GND
21
98
USB_D-
20
SP+
USB_D+
19
CN1001
REG_GND
18
33P
XF_TALLY_LED
ZOOM_MIC_CONT
LASER AF
ILLUMINATOR
USB_DET
17
INT_MIC_L
6
K
REG_GND
16
1
3
4
5
6
7
2
AU_GND
SHOE_MIC_L
MIC_L
AU_GND
MIC_R
AU_2.8V
AU_GND
8
FP-500
FLEXIBLE
LANC_DC
15
1
CN5903
I
AU_2.8V
8P
MIC902
R
(MICROPHONE)
LANC_SIG
14
D+
CN5904
MIC901
L
(MICROPHONE)
XLANC_JACK_IN
13
87
D-
2P
CN5901
XHP_JACK_IN
12
PHOTO_STBY
2
G
H
AV_JACK_IN
11
89
F
XS_JACK_IN
10
XPHOTO_FREEZE
VCC
5P
SP-
1
3
N.C.
9
NTPB
CN402
(USB)
DV_GND
8
4P
97
1
NTPB
7
91
TPB
TPB
6
HI EVER_SO
2
DV_GND
5
EVF_TALLY
NTPA
NTPA
4
93
3
TPA
3
REG_GND
DV
TPA
2
99
E
4
DV_GND
95
CN401
27P
1
100
CN1005
JK-222 BOARD
100P
D
REG_GND
FP-498 FLEXIBLE
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
1
2
3
4
6
5
7
4-3. PRINTED WIRING BOARDS
8
10
9
11
12
14
13
16
15
17
FRAME SCHEMATIC DIAGRAM (3/3)
18
TRV950/TRV950E
15P
2
KEY_AD5BACK
3
KEY_AD5IN
4
MENU
1
DISP_HD
2
2
DISP_VD
EXECUTE
CN5204
2P
REG_GND
3
3
REG_GND
REG_GND
4
4
REG_GND
PANEL_2.8V
5
5
PANEL_2.8V
PANEL_13.3V
6
1
SP+
PANEL_-15.3V
7
2
SP-
PANEL_4.6V
8
VD_SO
9
VD_SCK
9
VD_SO
10
6
N.C.
7
N.C.
8
N.C.
9
N.C.
10
N.C.
11
N.C.
12
LCD901
3.5INCH COLOR LCD UNIT
N.C.
13
N.C.
14
BL_HI
15
GND
6
GND
D
TP_L
18
18
TP_L
TP_BOT
19
19
TP_BOT
TP_TOP
20
20
TP_TOP
12
13
14
15
16
17
18
19
20
21
22
23
24
VBC
SRT
OE
CLR
MCLK
HCNT
VR
VG
VB
VSS
VDD
VSH
TP_R
STBYB
17
9
17
11
REG_GND
TP_R
VCOM
16
8
16
10
COM_OUT
REG_GND
RESET
P_UNREG_GND
15
STBYB
P_UNREG_GND
14
15
7
13
14
24P
13
COM_OUT
CN5701
5
P_UNREG_GND
P_UNREG_GND
1
P_OPEN
2
P_REVERSE
4
GSRT
P_UNREG
6
12
GPCK
12
5
P_UNREG
4
XCS_LCD_DAC
GRES
11
3
11
N.C.
XCS_LCD_DAC
PWM
GND
3
15
GND
REG_GND
2
14
GND
BT_XRST
3
13
BT_XRST
N.C
4
12
BT_BMCTEST1
BT_WAKEUP
5
11
BT_WAKEUP
PANEL_4.6V
6
10
LCD_4.6V
BT_XSLEEP
7
9
BT_XSLEEP
BT_MODE
8
9
ANT901
8
BT_BMCTEST0
7
BT_CTS
6
BT_RXDT
BT_RXDT
10
BT_TXDT
11
5
BT_TXDT
BT_RTS
12
4
BT_RTS
BT_RSSI
13
3
BT_RSSI
REG_GND
14
2
GND
REG_GND
15
1
GND
VD_SCK
GND
2
1
ND901
BACK LIGHT
6P
3
FP-495
FLEXIBLE
PANEL_4.6V
4
S002
(PANEL REVERS)
8
PANEL_4.6V
1
10
PANEL_-15.3V
5
N.C.
VDD
CN5206
PANEL_13.3V
7
5
C
6
4
N.C.
15P
15P
REG_GND
BT_CTS
BL_DET
HARNESS
(SC-115)
1
DISP_VD
P_UNREG
SP901
(SPEAKER)
DISP_HD
20P
P_UNREG_GND
8
CN5802
N.C.
BT-003 BOARD (Note)
CN1023
2
GND
20P
3
VGL
7
CN5201
2
BL_LOW
1
DIAL_B
1
LED
VSS
DIAL_A
6
CK-116 BOARD
BL_GND
VGH
5
INVERTER
TRANSFORMER UNIT
GND
5P
B
1
CN5805
CONTROL
SWITCH
BLOCK
(KP-1870)
8P
FP-491 FLEXIBLE
CN5205
HARNESS
(PC-087)
A
Note: BT-003 board is only replaced as a mounted board.
Therefore, schematic diagrams and printed wiring
boards are not shown.
PD-168 BOARD
BS
VCC
VSS
10
9
N.C
INS
N.C
DIO
8
7
6
5
COM4
COM3
SEG15
SEG16
SEG1
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
COM2
COM1
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
7
BS
10
6
VCC
MS_LED_VCC
5
DIO
9
4
ACCESS_LED
3
INS
8
2
VCC
SCLK
VSS
1
10P
VSS
CN1009
VHE-
CAP_U
CAP_U
CAP_U
CAP_U
N.C.
FG1
FG_VCC
FG_VCC
FG2
FG_GND
FG_GND
17
18
19
20
21
22
23
24
25
26
27
2
16
REG_GND
WHE-
REG_GND
CAP_W
1
CAP_W
1
15
REG_GND
14
REG_GND
CAP_W
4
2
13
D_2.8V
CAP_W
REG_GND
12
3
HE_GND
3
WHE+
REG_GND
11
D_2.8V
VHE+
6
4
9
SP-
10
BATT_LI_3V
UHE+
5
8
5
HE VCC
BATT_LI_3V
UHE-
SP-
7
8
6
CAP_V
10
SP+
6
XRESET_SW
REG_GND (N.C)
5
N.C
7
CAP_V
9
7
4
9
REG_GND (N.C)
3
N.C
SP+
27P
XRESET_SW
8
CN1007
10
CAP_V
DIAL_A
CAP_V
DIAL_B
2
12
1
13
TAPE_TOP
KEY_AD4
27
KEY_AD5
TOP/END_GND
14
TAPE_END
15
26
12
15
25
DIAL_B
KEY_AD2
SREEL+
DIAL_A
KEY_AD3
24
11
16
SREEL-
14
11
17
23
KEY_AD5
19
17
HALL_GND
KEY_AD4
19
KEY_AD6
TREEL-
16
13
N.C
REG_GND
18
22
KEY_AD3
REG_GND
20
21
18
KEY_AD2
XOSD_SCK
TREEL+
20
REG_GND
21
20
REG_GND
21
OSD_SO
HALL_VCC
22
N.C
KEY_AD6
XOSD_SCK
22
19
24
OSD_SO
LCD_COM/XDATA
LCD_COM/XDATA
CHIME_VDD
26
23
XCS_LCD_DRIVER
25
18
28
XCS_LCD_DRIVER
23
24
27
CHIME_SDA
30
VD_SO
ACCESS_LED
VC-288 BOARD (3/3)
CHIME_SCK
N.C
VD_SCK
XCS_LCD
VD_SO
ACCESS_LED
XCS_LCD
32
XREC_PROOF
29
25
VD_SCK
26
34
17
REG_GND
27
28
36
N.C
16
31
MIC/REC_SW_GND
REG_GND
N.C
REG_GND
TP_R
TP_BOT
14
29
30
33
TAPE_LED_A
REG_GND
N.C
35
TAPE_LED_K
31
32
TP_L
TP_TOP
13
TP_TOP
TP_BOT
12
TP_L
33
TP_R
34
XCCDOWN_SW
38
35
36
11
REG_GND
SW_COM/SW_GND
REG_GND
10
37
XMODE_SW_C
37
9
REG_GND
XMODE_SW_B
REG_GND
XMODE_SW_A
40
38
8
PANEL_B
7
N.C
DEW-
39
6
39
DEW+
N.C
LM_UNLOAD
PANEL_B
LM_UNLOAD
42
40
5
PANEL_G
LM_LOAD
C-SYNC/XHD
4
41
3
41
2
C-SYNC/XHD
27P
PANEL_G
CN1006
44
42
LM_LOAD
46
PANEL_R
1
PANEL_VG
PANEL_COM
PG
XVD
43
FG
45
43
1
45
PANEL_COM
2
XVD
PANEL_R
FG/PG_COM
PANEL_VG
44
M_COM
48
46
DRUM_U
EVER_3.0V
3
XHD_OUT
4
47
5
47
DRUM_U
XHD_OUT
6
EVER_3.0V
DRUM_V
50
48
7
P_UNREG
DRUM_V
P_UNREG_GND
8
49
10P
49
CN1022
P_UNREG_GND
DRUM_W
P_UNREG
DRUM_W
52
50
9
54
P_UNREG
10
PANEL_2.8V
P_UNREG_GND
GND
REG_GND
51
XEVEN
53
51
YEVEN
53
P_UNREG_GND
10
REG_GND
P_UNREG
GND
PANEL_2.8V
52
9
56
54
8
58
PANEL_13.3V
XODD
PANEL_-15.3V
REG_GND
7
REG_GND
55
YODD
57
55
GND
57
REG_GND
6
REG_GND
PANEL_13.3V
XSDL
PANEL_-15.3V
56
5
58
4
60
3
PANEL_4.6V
10P
REG_GND
YSDL
59
GND
J
59
2
I
REG_GND
CN1901
H
D001
(MS ACCESS)
FP-503
FLEXIBLE
60P
PANEL_4.6V
FP-496 FLEXIBLE
G
CN1003
60P
60
1
CN5203
SCLK
N.C
21
21P
7P
LCD902
CHARACTER DISPLAY
TA901
TOUCH PANEL
VCC
XHD_OUT
4
10
3
10
2
VG
XHD_OUT
VSS
PANEL_R
9
10P
PANEL_G
8
9
MEMORY
STICK
CONNECTOR
1
7
8
CN5803
7
VG
15
F
PANEL_G
PANEL_R
CN5804
PANEL_B
TP_L
6
NC
6
LCD_COM/XDATA
TP_R
EVER_3.0V
PANEL_B
XCS_LCD_DRIVER
4
1
5
3
2
5
3
4
EVER_3.0V
XOSD_SCK
NC
3
LCD_COM/XDATA
OSD_SO
2
4
XCS_LCD_DRIVER
1
TP_BOT
2
5
1
TP_TOP
OSD_SO
6
10P
10P
XOSD_SCK
HARNESS
(PC-088)
E
CN5806
NC
CN5202
7
S001
(PANEL OPEN)
K
VIDEO HEAD
(ODD,EVEN)
M901
DRUM
MOTOR
FP-102
FLEXIBLE
BOARD
L
MD (J-MECHANISM)
LM_LOAD
1
LM_LOAD
2
LM_UNLOAD
3
LM_UNLOAD
4
DEW+
5
DEW-
6
MODE A
7
MODE B
8
MODE C
9
FP-100
FLEXIBLE
BOARD
M903
CAPSTAN
MOTOR
FP-228
FLEXIBLE
BOARD
M902
CAPSTAN
MOTOR
DEW SENSOR
SW_COM/SW_GND 10
05
4-5
4-6
FRAME (3/3)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
Link
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
1m
Kinds of capacitor
Front of the lens
Temperature characteristics
External dimensions (mm)
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
• A: VIDEO SIGNAL (ANALOG)
• A: AUDIO SIGNAL (ANALOG)
• A: VIDEO/AUDIO SIGNAL
• A: VIDEO/AUDIO/SERVO SIGNAL
• A: SERVO SIGNAL
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Note :
A B
Red
Blue
White
Magenta
H
Cyan
Green
Yellow
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
A=B
B A
Fig. a (Video output terminal output waveform)
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please
include the board name.
Note :
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
4-9
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifie.
DCR-TRV940/TRV940E/TRV950/TRV950E
COVER
4-2. SCHEMATIC DIAGRAMS
Link
CD-389 BOARD (CCD IMAGER)
SE-132 BOARD (PITCH/YAW SENSOR)
MA-410 BOARD
(MIC AMP, AF LASER CONTROL)
CK-116 BOARD (CONTROL SWITCH)
JK-222 BOARD
(AV IN/OUT, DV/USB CONNECTOR)
PD-168 BOARD (2/2)
(LCD DRIVER, BACKLIGHT)
LB-080 BOARD (EVF, EVF BACKLIGHT)
FP-504 FLEXIBLE BOARD
FP-495, FP-497, FP-500, FP-503
FLEXIBLE BOARD
FP-100, FP-102, FP-228 FLEXIBLE BOARD
PD-168 BOARD (1/2)
CONTROL SWITCH BLOCK
(LCD DRIVER, TIMING GENERATOR)
(CF-1870, KP-1870, PS-1870)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
WAVEFORMS
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
CD-389 BOARD SIDE A
CD-389 BOARD SIDE B
For Schematic Diagram
• Refer to page 4-89 for printed wiring board.
• Refer to page 4-125 for waveforms.
1
2
4
3
6
5
7
8
CD-389 BOARD
A
9
10
11
12
14
13
15
SIGNAL PATH
VIDEO
SIGNAL
CCD IMAGER
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
R:REC MODE
P:PB MODE
*1 CCD IMAGER (IC100,101 and 105)is
supplied as a prism block.
R106 100
5
H2B
R7.5/
P0
VSUB
10 11 12 13 14
7
5
6
3
2
VC-288 (1/17)
1
1
CN1201
(PAGE 4-14)
L105
10uH
V4B
D
4
V3B
R103 0
C125
0.1u
R15.2/
P0
V2B
*1
V1B
CCD IMAGER (B)
VL
R-6.5/P0
V1
R-0.4/P0
V2
R-0.3/P0
V3
R-7/P0
V4
IC105
S/H (B)
-7.5
IC102
VDD
R7.9/P0
RCSUB
C108
0.1u
C
ICX427AL-13
9
C132
XX
IC105
8
GND
C120
0.1u
H1B
RGB
XSHDB
C119
0.1u
R1.5/P0
BYP
R12.6/P0
0.4
C130
0.1u
H2
6
NC
BYP
R1.1/P0
BYP
REC
R102
0
3
R109
0
R1.9/P0
GND
1.6
C121
0.1u
H1
OUT2
R0.6/P0
GND
1.3
CCD_IN
CCD_OUT
4
OUT1
0.6
4
GND
R13.9/P0
RG
3
VDD
2.8
R2.2/P0
SHP
R2.2/P0
SHD
10 11 12 13 14
2
GND
AD80017AJRURL
9
1
CLPDM
5
B
6
R2.8/
P0
C104
22u
4V
7
IC102
8
CLPDM
C105
0.01u
XSHPB
Y/CHROMA
L100
22uH
CN100
59
B_GND
B_GND
60
57
H2B
SHTB
58
55
H1B
B_GND
56
53
B_GND
RGB
54
51
CCD+B
B_GND
52
49
B_GND
CCD-B
50
47
XSHDB
B_GND
48
45
V4B
XSHPB
46
43
VDD_B
V3B
44
41
V2B
V1B
42
39
CLPDM
CSUB
40
H2B
C131
10u
10V
C122
0.01u
60P
H1B
RGB
2
7.9
0
XSHDB
Q102
UN9213J-(TX).SO
SWITCH
V4B
CSUB
V2B
Q100
UN9213J-(TX).SO
SWITCH
CLPDM
37
CSUB
V1R
V2R
0.1u
V4R
V3R
E
XSHPB
VL
V1R
38
V3R
36
CAM_2.9V
34
V2R
35
V2R
33
VDD_R
31
V4R
29
XSHDR
27
25
23
R_GND
V3B
V1B
CSUB
V1R
V3R
0
V4R
0
-7.5
R-6.8/P0
IC103
CCD IMAGER (R)
7
GND
6
NC
1.3
CCD_IN
XSHPR
CCD+R
CCD-R
22
19
R_GND
R_GND
20
17
V4G
V3G
18
15
VDD_G
V2G
16
13
V1G
XSHPG
14
11
XSHDG
SHTG
12
9
G_GND
H2G
10
7
RGG
H1G
8
5
G_GND
G_GND
6
3
CCD+G
CCD-G
4
1
G_GND
G_GND
2
V3G
V2G
XSHPG
5
0.6
2.8
GND
VDD
SHD
GND
CLPDM
SHP
IC103
12
H1G
R0.6/P1
3
OUT1
RGG
4
OUT2
2
R2.2/P0
XSHDR
9
BYP
BYP
R2.8/P0
1
R110 C112
0.1u
0
10
BYP
0.4
C116
0.1u
1.6
8
R1.1/
P0
9
R1.9/P0
C115
0.1u
11
8
RGR
H1R
24
H2G
C123
0.1u
14 13 12 11 10
9
R107 100
R1.5/P0
H2R
R100
0
CH
R_GND
XSHDG
R2.2/P0
LND100
26
V1G
IC100
GND
R12.6/P0
CCD_OUT
H1
R13.9/P0
RG
H2
GND
IC100
VSUB
C102
0.1u
28
H1R
H1R
21
*1
R7.5/P0
H2R
RGR
7
VDD
6
VL
R7.9/P0
RCSUB
5
14 13 12 11 10
C100
XX
R_GND
V4G
S/H (R)
H
30
H2R
L101
10uH
R15.2/
P0
V1
4
V2
V3
3
32
SHTR
RGR
C126
0.01u
G
2
V4
ICX427AL-13
1
R-0.4/P0
R-0.3/P0
8
R-7/
P0
XSHPR
XSHPR
XSHDR
C113
10u
10V
C109
0.01u
R104
F
7.9
C106
7
C128
22u
4V
L103
22uH
CLPDM
AD80017AJRURL
CH
LND101
R105
-7.5
VL
R7.9/P0
RCSUB
16
R111 C111
0
0.1u
R2.2/P0
XSHPG
15
XSHDG
RGG
H1G
R101
0
H2G
R2.2/P0
L
8
1.3
NC
OUT2
CCD_IN
OUT1
GND
SHD
SHP
IC104
1.6
BYP
BYP
0.4
C118
0.1u
GND
BYP
9
8
R1.1/
P0
14 13 12 11 10
R1.9/P0
R108 100
GND
R12.6/P0
CCD_OUT
H1
R13.9/P0
RG
H2
GND
IC101
R1.5/P0
9
C117
0.1u
17
Precautions for Replacement of CCD Imager
• The CD-389 board mounted as a repair part is not equipped
with a CCD imager.
When replacing this board, remove the CCD imager from the
old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
C124
0.1u
S/H (G)
R0.6/P1
0.6
2.8
VDD
GND
CLPDM
18
R2.8/P0
C127
0.01u
V1
IC104
7
V2
IC101
6
V3
7
*1
14 13 12 11 10
C103
0.1u
6
5
5
4
4
3
3
VDD
2
CCD IMAGER (G)
R7.5/P0
C101
XX
L102
10uH
2
R-6.8/P0
1
VSUB
K
C114
10u
10V
R15.2/
P0
V4
ICX427AL-13
R-7/
P0
R-0.4/P0
R-0.3/P0
J
Q101
UN9213J-(TX).SO
SWITCH
C110
0.01u
0
C107
14
CLPDM
CSUB
0
7.9
1
13
0.1u V1G
V2G
V3G
V4G
I
L104
22uH
C129
22u
4V
AD80017AJRURL
05
4-11
4-12
CD-389
Schematic diagrams of the VC-288, DB-014 boards are not shown.
Pages from 4-13 to 4-64 are not shown.
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
SE-132 BOARD
For Schematic Diagram
• Refer to page 4-101 for printed wiring board.
1
2
3
4
5
6
8
7
9
SE-132 BOARD
A
PITCH/YAW SENSOR
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
R:REC MODE
P:PB MODE
2
R1.4/
P0
R1.4/
P0
3
L4001
10uH
1
4
2
R4001
22k
R4004
22k
OUT2
C_RESET
VCC
0
R2.8/
P0.5
AM2
R4005
10k
C4009
10u
C4007
0.047u
C4011
10u
R1.2/
P0
Vref2
20
R1.3/
P0
HO2
19
R1.4/
P0
HI2
18
R1.3/
P0
LO2
17
R1.3/
P0
LIA2
16
R1.3/
P0
LIB2
15
R0.8/
P0
14
C4005
0.047u
BOTTOM VIEW
E
13
4-65
D_2.8V
2
PITCH_AD
3
REG_GND
4
YAW_AD
5
C_RESET
6
VAP_DD_ON
7
REG_GND
8
REG_GND
JK-222
LND465-LND472
C4015
0.1u
R4007
1M
R4012
XX
C4016
XX
05
SE-132
8P
1
2.9
R2.8/
P0
PITCH/YAW SENSOR
AMP
12
C4003
0.1u
3
1
SE4002
YAW SENSOR
CN4005
IC4001
11
R0.6/
P0
C4002
22u
4V
R4011
47k
Q4001
2SB1462JQR(K8).SO
SWITCH
IC4001
NJM3230V(TE2)
D
2.8
R2.1/
P2.9
PASS
4
OUT1
5
R4009
1M
R1.4/
P0
R1.4/
P0
R1.5/
P0
C4012
10u
6
HI1
7
HO1
R1.5/
P0
R1/
P0
R0.7/
P0
8
LO1
GND
C
9
LIB1
10
LIA1
4
C4004
0.1u
R0.1/
P0
R4010
1k
C4014
22u
4V
R4008
XX
R4006
10k
C4010
10u
AM1
C4008
0.047u
R4003
22k
C4006
0.047u
BOTTOM VIEW
2
C4013
XX
3
1
SE4001
PITCH SENSOR
C4001
22u
4V
R4002
22k
Vref1
B
Q4002
UN9213J-(K8).SO
SWITCH
4-66
(PAGE 4-71)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
MA-410 BOARD
For Schematic Diagram
• Refer to page 4-103 for printed wiring board.
2
3
4
5
MA-410 BOARD
R5903
18k
MIC AMP,
AF LASER CONTROL
7
8
R5904
33k
C5903
XX
D5901
XX
R5909
6800
R5923
0
C5921
0.1u
GND
C5902
XX
C5919
XX
C5915
0.001u
C5914
100p
R5901
0
J5901
MIC
(PLUG IN POWER)
15
16
CN5901
INT_MIC_L
1
INT_MIC_GND
2
R5942
XX
R5944
150
0
C5907
0.022u
R5947
820
1.4
0
1.4
1.4
1.4
1.4
MIC902
(MICROPHONE)
1.4
2
1.4
INT_MIC_GND
1.4
1
1.4
HPF_OUT_L
EXT_MIC
GND
HPF_ON/OFF
R_OUT
4
5
6
7
8
9
1.4
6
5
2
Q5903
XP4313(TX).SO
4.9
PHOTO
SENSOR SWITCH
4
1
C5913
100p
C5911
0.001u
2.8
R5933
2.9
2.7
C5933
0.1u
0
C5935
10u
6.3V
C5936
0.22u
1.8
0.1u
C5920
C5904
XX
LND592
REG_GND
2
SIRCS_DRV_CL
3
X_SIRCS_IN
4
A_4.6V
5
KEY_AD1M
6
MT_4.9V
7
MF_B
8
MF_A
FP-504
FLEXIBLE
LND601-LND616
(PAGE 4-80)
9
GND
10
GND
11
MF_LED
12
SCHARGE_LED
13
XTALLY_LED
14
A_2.8V
15
MT_GND
16
N.C.
33
XF_TALLY_LED
32
MF_LED
31
MF_A
30
MF_B
29
SCHARGE_LED
28
KEY_AD1M
R5935
33k
27
A_2.8V
R5934
18k
26
REG_GND
25
SENS_ON
24
A_4.6V
23
PHOTO_TR_OUT
22
REG_GND
21
XSIRCS_IN
20
AU_GND
19
ZOOM_MIC_CONT
18
AU_2.8V
17
EXT_MIC_DET
16
REG_GND
15
AU_GND
14
AU_GND
13
MT_4.9V
12
MT_4.9V
11
REG_GND
10
XMIC_MONO
L5901
100uH
R5950
XX
C5926
8200p
R5928
5100
Q5905
UN5113
-TX
BUFFER
0
C5930
0.01u
R5924
0
C5925
0.047u
1
1.5
R5931
33k
R5921
9100
AU_2.8V
1.4
2.9
R5910 6800
H
AU_2.8V
1200
R5911
1k
C5917
100p
AU_GND
7
2.9
1.4
R5920
15k
6
JK-222
LND451-457,462
(PAGE 4-71)
1.4
10 11 12
R5917
2200
MIC_R
CN5906 33P
C5922
0.1u
C5916
XX
AU_GND
5
R5948
100
C5909
0.022u
G
MIC_L
4
0
C5937
22u
4V
HPF_AMP_IN_R
MTX_AMP_IN_R
3
NC
HPF_OUT_R
SUB_SIG_OUT_R
2
1.4
1
2.2
C5943
XX
1.4
INVT_OUT_R
SUB_IN_R
C5905
0.022u
MTX_AMP_OUT_R
C_1/2VCC
13 14 15 16 17 18 19 20 21 22 23 24
MTX_AMP_IN_L
SUB_SIG_OUT_L
MTX_AMP_OUT_L
SG_IN_L
AMP_OUT_L
MODE_CTL_2
EXT_IN_L
INT_IN_L
INVT_OUT_L
VCC
MIX_OUT
1.4
F
1.4
ZOOM_BAL
ZOOM_POSI
MIC AMP
IC5901
AN2901FHQ-EB
SG_IN_R
1.4
C5912
10u
6.3V
NC
1.4
1.4
IC5901
ZOOM_AMP_IN
1.4
R5906
10k
MIC_MONO
ZOOM_AMP_OUT
AMP_OUT_R
C5908
0.01u
L_OUT
NC
1.4
E
HPF_AMP_IN_L
NC
MODE_CTL_1
1.4
R5945
XX
GND
EXT_IN_R
1.4
C_REG
REG_2.5V
R5905
4700
1.2
INT_IN_R
C5910
10u
6.3V
48 47 46 45 44 43 42 41 40 39 38 37
(Note)
Note: C5944 and C5945 are mounted on
the board with suffix number 12.
REG_2.5V
SUB_IN_L
C5945
0.001u
2.3
C5944
0.001u
4.9
R5946
0
36 35 34 33 32 31 30 29 28 27 26 25
D
4.9
3
R5949
47k
2.3
INT_MIC_R
AU_GND
3
CN5905 16P
C5906
0.022u
2P
SHOE_MIC_L
2
C5941
0.1u
C5939
0.1u
R5941
5600
0.5%
C5924
0.1u
C5942
XX
FB5902
1
8
C5927
8200p
17
CN5904 8P
CN5902 2P
R
14
R5927
5100
R5916
2200
C5901
2200p
B
C
13
R5943
11k
0.5%
R5938
11k
0.5%
C5929
6800p
C5918
100p
R5908
2200
VDR591
D5902
XX
L
12
R5918
15k
LND591
MIC901
(MICROPHONE)
11
C5940
0.1u
C5938
0.1u
R5912
1k
R5907
2200
10
C5928
0.015u
R5922
470
FB5901
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
9
C5923
0.047u
VDR592
A
6
R5919
9100
1
R5925
470
C5931
0.015u
2.9
Q5904-5906
IR LED DRIVE
R5951
470
1
Q5906
2SD999-T1
-CLCK
0
0
R5953
8.2
AF_LD_VCC
8
AF_LD_VCC
7
PD_OUT
6
LD_EVR
5
SAFE_ON
4
MT_GND
3
MT_GND
2
SIRCS_PWM
1
N.C
CN1021
THROUGH THE
FP-494 FLEXIBLE
(PAGE 4-42)
0.2
A
R5902
0
9
VC-288
(15/17)
R5952
330
Q5904
UN5213
-TX
I
C5932
10u
6.3V
0.3
J
Q5901
2SB1462JQR(K8).SO
R5936
2200
R5939
820
SIGNAL PATH
R5932
XX
AUDIO
SIGNAL
2 2.1
0
CN5903 6P
(PAGE 4-81)
1
AF LASER CONTROL
6
3
5
K
R5937
22k
0
-
IC5902
0
R5914
33
FP-500
FLEXIBLE
G
R5940
10k
C5934
0.1u
IC5902
NJM2125F(TE2)
AF LASER
CONTROL
D5903
01ZA8.2(TPL3)
O
0
0
+
2
R5930
1500
5
R5929
470
0
V
4
0
3
R5926
4700
LD_EVR
1
PD_OUT
2
MTGND
3
PHOTO_TR_C(N.C)
4
PHOTO_TR_E(N.C)
5
N.C
6
R5913
XX
R5915
33
0
4
1
Q5902
XP4313(TX).SO
SAFE SWITCH
REC
05
4-67
4-68
MA-410
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
CK-116 BOARD SIDE A
CK-116 BOARD SIDE B
For Schematic Diagram
• Refer to page 4-105 for printed wiring board.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
CK-116 BOARD
CONTROL SWITCH
A
XX MARK:NO MOUNT
VC-288(16/17)
CN1003
(THROUGH THE FP-496 FLEXIBLE)
(PAGE 4-43)
B
CN5204 2P
PANEL_4.6V
PANEL_-15.3V
PANEL_13.3V
60
PANEL_4.6V
REG_GND
59
58
PANEL_-15.3V
REG_GND
57
56
PANEL_13.3V
REG_GND
55
54
PANEL_2.8V
REG_GND
53
52
P_UNREG
P_UNREG_GND
51
50
P_UNREG
P_UNREG_GND
49
48
EVER_3.0V
XHD_OUT
47
46
PANEL_VG
XVD
45
PANEL_R
44
PANEL_R
43
PANEL_COM
PANEL_G
42
PANEL_G
C-SYNC/XHD
41
40
PANEL_B
N.C
39
38
REG_GND
REG_GND
37
CN5205 8P
DISP_HD
33
REG_GND
31
30
N.C
REG_GND
29
TP_R
TP_BOT
D
R5243
470
VD_SCK
28
VD_SCK
26
XCS_LCD
VD_SO
27
ACCESS_LED
25
LCD_COM/XDATA
23
XOSD_SCK
21
TP_TOP
R5244
0
C5202
0.1u
C5201
10u
16V
DATA CODE
VD_SO
R5211 0
R5217 1500
R5213 1200
A
3
XCS_LCD
XCS_LCD_DRIVER
24
XCS_LCD_DRIVER
22
OSD_SO
OSD_SO
E
20
REG_GND
N.C
19
18
REG_GND
KEY_AD6
17
16
KEY_AD3
KEY_AD2
15
14
KEY_AD5
KEY_AD4
13
12
DIAL_B
DIAL_A
11
10
XRESET_SW
N.C
9
8
SP+
REG_GND
7
6
SP-
BATT_LI_3V
5
4
D_2.8V
REG_GND
3
2
REG_GND
REG_GND
1
CN5203
LCD_COM/XDATA
-
R5221 2200
B
4
S5203
+
OFF
R5231 8200
R5226 3900
70%
R5241
XX
100%
S5202
R5235 27k
R5240
0
R5203
XX
STOP
R5212 0
A
3
R5214 1200
B
4
S5206
REW
A
3
R5218 1500
B
4
S5207
+
60P
R5208 0
R5215 1200
A
B
3
4
S5213
A
3
FF
REC
R5222 2200
R5227 3900
B
A
B
4
3
4
S5208
S5209
R5232 8200
A
3
DISPLAY/
TOUCH PANEL
-
REG_GND
3
REG_GND
4
DIAL_A
(KP-1870)
6
DIAL_B
(PAGE 4-85)
7
GND
8
EXECUTE
R5238 27k
B A
B
4 3
4
S5211
S5212
AUDIO_DUB
R5228 3900
R5223 2200
R5219 1500
A
B
A
B
A
B
3
4
3
4
3
4
S5214
S5215
S5116
R5233 8200
A
3
R5236
B
4
27k
S5217
CN5206 6P
R5209
0
R5216 1200
R5220 1500
R5224 2200
R5229
A
3
B
4
3900
SPOT_LIGHT
R5234 8200
S5218
R5237 27k
A
3
S5219
S5210
DISP_VD
CUSTOM_PRESET
D5207
01ZA8.2(TPL3)
BACK_LIGHT
DISP_HD
2
5
B
4
1
GND
2
GND
3
P_REVERSE
4
P_OPEN
5
GND
6
GND
S5220
R5206
XX
PANEL_2.8V
PANEL_2.8V
5
PANEL_13.3V
6
PANEL_-15.3V
7
PANEL_4.6V
8
PANEL_13.3V
R5210
0
PANEL_-15.3V
R5225
8200
A
3
PANEL_4.6V
H
(PAGE 4-75)
XCS_LCD_DAC
11
P_UNREG
12
P_UNREG_GND
13
P_UNREG_GND
14
COM_OUT
15
REG_GND
16
TP_R
17
TP_L
18
AUTO_LOCK_SW
AUTO
LOCK
TP_R
BT5201
LITHIUM
BATTERY
(SECONDARY)
D5204
MAZS082008SO
S5201
R5207
XX
COM_OUT
I
C5203
XX
R5230
27k
D5203
01ZA8.2(TPL3)
THROUGH THE
PC-087 HARNESS
XCS_LCD
D5202
01ZA8.2(TPL3)
9
10
D5201
MAZS082008SO
VD_SO
VD_SO
VD_SCK
CN5802
RESET
B
4
S5221
VD_SCK
PD-168(2/2)
AUTO LOCK
RELEASE
HOLD
LN5201
TP_L
SEIDEN_GND
TP_BOT
TP_BOT
19
TP_TOP
20
LN5202
TP_TOP
SEIDEN_GND
SIGNAL PATH
LN5203
CN5202 10P
OSD_SO
J
OSD_SO
1
XOSD_SCK
2
XCS_LCD_DRIVER
3
SEIDEN_GND
VIDEO SIGNAL
XOSD_SCK
(PAGE 4-75)
AUDIO
SIGNAL
LCD_COM/XDATA
LCD_COM/XDATA
4
EVER_3.0V
5
PANEL_B
6
PANEL_G
7
CN5806
THROUGH THE
PC-088 HARNESS
LN5204
CHROMA
XCS_LCD_DRIVER
PD-168(2/2)
EVER_3.0V
REC
SEIDEN_GND
PANEL_B
PANEL_G
PB
PB
PANEL_R
PANEL_R
8
PANEL_VG
K
VG
9
XHD_OUT
10
XHD_OUT
05
CK-116
4-69
CONTROL
SWITCH
BLOCK
R5242
XX
PLAY
COLOR BAR
CN5201 20P
1
MENU
VOLUME
R5204
XX
R5205
XX
DISP_VD
KEY_AD5IN
4
S5205
PAUSE
DISP_HD
KEY_AD5BACK
3
S5204
XOSD_SCK
F
G
GND
2
ZEBRA_SW
EDIT SEARCH
R5202
XX
1
D5206
01ZA8.2
(TPL3)
35
TP_TOP
N.C
TP_L
D5209
01ZA8.2
(TPL3)
TP_L
TP_BOT
32
R5239
0
D5205
01ZA8.2
(TPL3)
TP_R
34
SP901
(SPEAKER)
DISP_VD
COM_OUT
PANEL_B
36
SP-
XHD_OUT
PANEL_VG
C
SP+
2
D5208
01ZA8.2(TPL3)
PANEL_2.8V
EVER_3.0V
1
4-70
FP-495
FLEXIBLE
(PAGE 4-81)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
JK-222 BOARD SIDE A
JK-222 BOARD SIDE B
For Schematic Diagram
• Refer to page 4-109 for printed wiring board.
1
2
4
3
5
6
7
9
8
10
12
11
13
SIGNAL PATH
JK-222 BOARD
VIDEO SIGNAL
C
AV IN/OUT,DV/USB CONNECTOR
A
XX MARK:NO MOUNT
B
DB-014 (8/9)
CN7204
(PAGE 4-61)
C
Y
J401
S
S
1
S_Y_OUT
LND402
S_Y_GND
LND403
S_C_OUT
LND404
S_C_GND
LND405
V_I/O
LND406
V_GND
LND407
L_I/O
LND408
V_GND
LND409
R_I/O
LND410
A_GND
4
TPA
LND411
HP_L
3
NTPA
LND412
A_GND
2
TPB
LND413
HP_R
1
NTPB
LND414
MA_GND
LND415
MIC_L
LND416
MA_GND
LND417
MIC_R
LND418
MA_GND
LND419
SHOEMIC_L
LND421
AU_2.8V
R402
0
R403
R401
0
PB
GND
0
VDR402
40p
VDR403
40p
R410
0
CN401
4P
CN401
DV
LND459
GND
FB406
J404
VDR407
1000p
FB407
AUDIO/VIDEO
ID-2
VDR408
1000p
R408
0
AU_2.8V
VDR409
40p
FB403
1
LND451
SHOE_MIC_L
LND452
AU_GND
LND453
MIC_L
MA-410
LND454
AU_GND
CN5904
(PAGE 4-68)
LND455
MIC_R
LND456
AU_GND
LND457
AU_2.8V
LND462
AU_2.8V
E
J403
(HEAD PHONE)
FB404
VDR404
1000p
VDR406
1000p
R411
0
8
R406
0
F
G
VC-288 (15/17)
CN1005
(PAGE 4-42)
H
TPA
LND426
NTPA
LND427
DV_GND
LND428
TPB
LND429
NTPB
LND430
DV_GND
LND431
N.C.
LND432
XS_JACK_IN
LND433
AV_JACK_IN
LND434
XHP_JACK_IN
LND435
XLANC_JACK_IN
LND436
LANC_SIG
LND437
LANC_DC
LND438
REG_GND
LND439
USB_DET
LND440
REG_GND
LND441
USB_D+
LND442
USB_D-
LND443
REG_GND
LND444
REG_GND
LND445
VAP_DD_ON
USB
LND460
LF401
USB
USB
4
3
1
2
4
3
1
2
LF402
R407
10k
USB
USB
CN402
1
VCC
2
D-
3
D+
4
ID
5
GND
5P
(USB)
D403
XX
GND
LF403
XX
USB
USB
USB
USB
LND458
D402
01ZA8.2(TPL3)
1
LND465
REG_GND
LND466
REG_GND
LND467
VAP_DD_ON
REG_GND
SE-132
LND468
C_RESET
LND447
C_RESET
YAW_AD
YS_OUT
CN4005
(PAGE 4-66)
LND469
LND448
LND470
REG_GND
LND471
PITCH_AD
LND472
D_2.8V
PS_OUT
D_2.8V
27
I
GND
R404
10k
USB
LND446
LND450
LND461
DV_GND
LND425
LND449
GND
R409
0
1
LND424
AUDIO
SIGNAL
LND473
21
D
Y/CHROMA
REC
LND401
LND422
Y
S VIDEO
ID-2
G
G
VDR401
1000p
CHROMA
FB401
J402
LANC
FB402
VDR405
8
D401
01ZA8.2(TPL3)
FB405
05
4-71
4-72
JK-222
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
PD-168 BOARD
For Schematic Diagram
• Refer to page 4-113 for printed wiring board.
• Refer to page 4-130 for waveforms.
1
2
3
4
5
6
7
8
9
10
11
12
PD-168 BOARD (1/2)
A
13
14
SIGNAL PATH
VIDEO SIGNAL
LCD DRIVER,
TIMING GENERATOR
10uH
L5703
CHROMA
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
C5711
3.3u
20V
L5704
10uH
C5712
0.1u
C5716
10u
10V
C5715
0.1u
REC
C5704
0.01u
C5705
0.01u
C5706
0.01u
PANEL_G
E
PANEL_R
1.9
1.9
13.5
IC5701
AN12580A-BB
GND1
XP.SAVE
B_IN
G_IN
19
GND2
LPF_ADJ
VSH
3
Vcc4
2
N.C
R_IN
N.C
2
1
3
4
5
BIAS
N.C
N.C
N.C
N.C
N.C
N.C
1
6
7
8
9
10
11
VB
R5737 100
R5732 100
C5721
1u
R5721
10k
2.2
COM_OUT
C5722
6.8u
16V
17
TRAP_ADJ
2.2
2
(2/2)
VR
2.2
18
R_DC_DET
LCD DRIVER
VG
VR
4
IC5701
Vcc1
VR
VG
C5720
1u
R5736 100
G_DC_DET
XCS
2.2
20
SI
VG
VG
C5719
1u
2.2
22
B_DC_DET
5
XSCK
2.2
21
XC.SAVE
VB
VB
2.2
24
GND3
6
EXT_DA2
23
BLACK_IN
25
Vcc2
N.C
BGP
26
Vcc3
EXT_DA1
FRP
R_INJECT
4.5
27
4.5
16
38
39
7
28
13.5
CN5701
C5723
0.1u
C5724
0.1u
C5726
1u
VSH
23
VDD
VB
20
VG
19
VR
TG24
12
18
HCNT
17
MCLK
16
CLR
15
OE
14
SRT
13
STBYB
12
VBC
11
VCOM
TG23
F
R5710
68k
TG21
C5707
10u
6.3V
(2/2)
C5709
0.1u
C5714
0.1u
C5713
560p
R5709
47k
R5714
100k
R5712
68k
1
TG20
R5708
2700
R5711
22k
VSS
21
TG22
L5702
10uH
24P
24
22
R5727
56k
1.8
29
15
2.8
1.4
30
14
XP.SAVE
PANEL_B
31
13
1
32
N.C
0.5%
1.4
33
VCO
R5703 27k
1
0.2
34
OP_OUT
C5702
0.1u
0.5%
2.7
35
OP_IN-
R5702 33k
C5701
68u
4V
0.1
36
OP_IN+
2.9
PANEL_2.8V
40
2.8
41
XCS_PANEL
42
2.2
43
XTG_SO
44
2.8
45
D
VD_SCK
46
R5701
470k
L5701
10uH
2.9
47
1.4
XC.SAVE
48
C
37
0
COM_FRP
PANEL_4.6V
N.C
PANEL_13.3V
COM_OUT
FRP
COM_FRP
BGP
B
BLK
PB
C5710
0.01u
R5707
15k
PANEL_-15.3V
D5702
1SV288(TPH3)
R5713
1M
TG18
TG17
C5717
0.001u
10
LCD901
COLOR
LCD UNIT
RESET
9
STBYB
8
GSRT
7
GPCK
TG16
G
TG15
C5718
47p
L5705
2.2uH
TG14
6
GRES
TG13
REG_GND
N.C
4
VDD
3
H
XC.SAVE
C5703
0.1u
R5706
100k
XP.SAVE
VD_SCK
VD_SCK
5
R5722
10k
9
2.8
VGL
2
VSS
1
VGH
C5727
1u
Q5701
2SD2216J-QR
(K8).SO
RESET
2.9
36
35
34
33
32
31
30
29
28
27
26
25
PD
XC.SAVE
OSCI
OSCO
DR.P.SAVE
2.8
PS/VDD
1.5
GND
1.4
-IN/TESTO
2.9
+IN/TESTO
1.4
OUT/TESTO
C5708
0.1u
2.9
SYF
2.8
POCB
R5705
470k
D5701
MA111-TX
0
XVD
VD_SO
L
XCS_PANEL
SO
GSRT
SI
GPCK
VSYB
GRES
XVD
CP
XCS_PANEL
SYNC
1
2.6
2
3
2.9
4
BL-DET
BL-ON
7
VD_SO
5
2.8
6
2.9
7
8
9
10
2.9
11
24
23
22
21
20
19
18
39
40
41
8
XVD
17
STBYB
16
XCS
XHD_OUT
SYNC
RESET
15
IC5702
CM7021L3-E2
W/H
XVD
VDD
TIMING GENERATOR
VDD/TESTI
HDB
SYNC
XSCK
HDI
XHD_OUT
2.8
48
K
SRT
IC5702
14
2.7
COM_FRP
13
VD_SO
OE
TG24
1.4
1.4
R5717
0
R5719
120 TG23
0
TG22
2.8
TG21
0.1
TG20
Q5702
UN9213J(K8).SO
INVERTER
0.2
BL_DET
2.9
0
TG18
2.9
TG17
0
TG16
0.1
TG15
3
2.6
TG14
(2/2)
0.5
TG13
CPMODE/CLS
2.2
CLR
FRP
TESTI
XTG_SO
SW
TESTI
2.8
47
XCS_PANEL
MCLK
PWM
2.9
SWCOM
LED
J
2.8
HCNT
TESTI/GND
VD_SCK
1.4
42
COM_FRP
43
1.4
44
FRP
45
0.2
46
BLK
BGP
GND/TESTI
2.7
38
BGP
37
2.9
I
12
2.9
XHD_OUT
PWM
BL
05
PD-168 (1/2)
4-73
4-74
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
PD-168 BOARD
For Schematic Diagram
• Refer to page 4-113 for printed wiring board.
12
13
COM4
COM3
SEG15
SEG1
SEG16
SEG14
SEG13
11
SEG12
SEG9
SEG12
SEG10
SEG13
1.5
SEG8
SEG14
1.5
NO MARK:REC/PB MODE
SEG7
SEG15
1.5
XX MARK:NO MOUNT
SEG11
SEG16
1.5
1.5
LCD DRIVER,BACKLIGHT
COM1
PD-168 BOARD (2/2)
A
10
9
SEG11
8
7
SEG6
6
SEG5
5
SEG4
4
SEG3
3
SEG2
2
COM2
1
1.5
2
3
LCD_COM/XDATA
4
EVER_3.0V
5
PANEL_B
6
PANEL_B
PANEL_G
7
PANEL_G
PANEL_R
8
PANEL_R
VG
9
CK-116
CN5202
THROUGH THE
PC-088 HARNESS
SEG6
SEG5
VDD
SEG4
SCK
SEG3
SO
9
SEG9
1.5
SEG8
1.5
SEG7
1.5
SEG6
1.5
SEG5
1.5
SEG4
1.5
SEG3
16
17
18
19
20
21
SEG1
SEG16
SEG15
COM3
COM4
N.C
14
SEG13
15
13
SEG14
12
SEG12
8
SEG7
11
7
SEG6
SEG10
6
SEG5
SEG11
5
SEG4
9
4
SEG3
10
3
SEG2
SEG9
2
COM2
SEG8
1
COM1
21P
SEG10
1.5
CN5804
SEG12
SEG13
SEG14
SEG15
SEG16
SEG11
SEG7
1.5
LCD902
CHARACTER DISPLAY
SEG2
XOSD_SCK
XCS_LCD_DRIVER
VLCD
XCS
C
8
0
SEG8
LCD DRIVER
IC5801
BU9735K-E2
VC
SEG1
1
IC5801
VSS
COM4
OSD_SO
7
3
OSC2
COM3
6
3
10P
SEG9
COM2
4
3
5
R5801
100
CN5806
3
C5801
0.1u
SEG10
OSC1
COM1
3
2
2
C/XD
1
R5802
680k 1.6
17 18 19 20 21 22 23 24
B
SEG17
SEG18
32 31 30 29 28 27 26 25
10 11 12 13 14 15 16
1.5
1.5
COM4
SEG1
1.5
SEG2
1.5
COM3
XHD_OUT
1.5
10
COM2
XHD_OUT
0
1.5
D
3
COM1
(PAGE 4-69)
BL
CN5802
20P
E
1
SYNC
DISP_VD
2
XVD
REG_GND
3
REG_GND
REG_GND
3
R5803
4700
3.7
4
PANEL_2.8V
6
PANEL_13.3V
0.1
7
PANEL_-15.3V
PANEL_4.6V
8
PANEL_4.6V
VD_SO
9
VD_SO
VD_SCK
10
VD_SCK
11
XCS_PANEL
P_UNREG
12
P_UNREG_GND
13
P_UNREG_GND
COM_OUT
REG_GND
G
COM_OUT
16
VG
17
TP_L
18
TP_BOT
19
TP_TOP
20
NC
1
TP_R
2
TP_L
3
NC
4
BL_DET
15
BL_HI
PWM
14
N.C.
13
N.C.
12
N.C.
11
N.C.
LND581
L5801
4.7uH
C5804
XX
C5802
47u
16V
C5803
0.1u
Q5801
UN9214J-(K8).SO
SWITCH
R5805
0
R5806
XX
CN5805
5P
1
PWM
2
PANEL_4.6V
3
BL_DET
4
P_UNREG_GND
5
15
ND901
BACK LIGHT
15P
2.9
14
TP_R
(1/2)
C5807
1u
A
XCS_LCD_DAC
(PAGE 4-69)
H
C5806
XX
5
THROUGH THE
TA901
TOUCH PANEL
C5805
10u
PANEL_2.8V
CN5201
CN5803
C5808
22u
10V
PANEL_13.3V
CK-116
F
(1/2)
R5804
1k
PANEL_-15.3V
PC-087 HARNESS
1
DISP_HD
Q5802
2SB1462J-QR(K8).SO
SWITCH
4.5
4.5
L5802
100uH
INVERTER
TRANSFORMER
UNIT
10
N.C.
9
N.C.
8
N.C.
7
N.C.
6
N.C.
5
N.C.
4
N.C.
3
BL_LOW
2
LED
1
BL_GND
P_UNREG
2
(1/2)
SIGNAL PATH
(LED)
VIDEO SIGNAL
7P
TP_BOT
5
TP_TOP
6
NC
7
CHROMA
REC
PB
05
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
4-75
4-76
Les composants identifiés par une marque 0 sont
critiques pour la sécurité. Ne les remplacer que
par une piéce portant le numéro spécifié.
PD-168 (2/2)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
Ver 1.1 2002. 09
LB-080 BOARD
For Schematic Diagram
• Refer to page 4-115 for printed wiring board.
1
2
3
5
4
6
7
LB-080 BOARD
A
EVF,EVF BACKLIGHT
D6101
CL-170R-CD-T
(TALLY)
XX MARK:NO MOUNT
R6101
390
NO MARK:REC/PB MODE
SIGNAL PATH
0
VIDEO SIGNAL
6
3
4.5
0
2.9
B
CHROMA
2
Q6101
RN4983FE(TPL3)
SWITCH
REC
D6102
NSCW100-T39
(BACK LIGHT)
R6105
33k
5
1
R6104
3300
4
4.5
PB
IC6101
R6102
180k
0.5%
BACK LIGHT CONTROL
E
20P
EVF_4.6V
1
XTALLY_LED
2
4.5
1
2
4
5
IC6101
NJM2125F(TE2)
3
1
1
Q6102
HN1B04FE-Y/
GR(TPL3)
0.3
LED DRIVE
R6106
22
0.5%
TH6101
R6107
XX
C6101
0.1u
LED_DA
3
4
EVF_GND
5
16
EVF_GND
6
15
VG
COM
7
14
VR
DB-014
(7/9)
VG
8
13
VB
VR
9
12
BLK
CN7211
THROUGH THE
FP-547 FLEXIBLE
VB
10
11
HCK1
F
CN6102
16P
COM
BLK
11
10
HCK1
12
9
HCK2
13
8
RGT
HST
14
7
DWN
EN
HCK2
HST
EN
15
6
STB
16
5
STB
VCK
17
4
VCK
VST
18
3
VST
EVF_GND
19
2
VSS
EVF_VCC
20
1
VDD
C6102
2.2u
05
4-77
2
0.4
LED_ON/OFF
(PAGE 4-60)
LB-080
1.4
6
4
0.3
3
0.5%
D
R6103 33k
CN6101
VCC
5
1
0.3
C
4-78
LCD903
COLOR
EVF UNIT
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
FP-504 FLEXIBLE BOARD SIDE A
FP-504 FLEXIBLE BOARD SIDE B
For Schematic Diagram
• Refer to page 4-117 for printed wiring board.
1
2
3
4
5
6
9
1
FP-504 FLEXIBLE BOARD
A
8
7
NO MARK:REC/PB MODE
REG_GND
LND613
SIRCS_DRV_CL
LND615
X_SIRCS_IN
LND612
A_4.6V
LND611
KEY_AD1M
LND607
MT_4.9V
LND606
MF_B
LND604
MF_A
LND603
MA-410
CN5905
(PAGE 4-68)
B
LND602
GND
D607
01ZA8.2(TPL3)
R603
220
PH601
CNA1312K01S0
PH602
CNA1312K01S0
GND
LND601
MF_LED
LND605
SCHARGE_LED
LND610
XTALLY_LED
LND614
A_2.8V
LND609
MT_GND
LND608
16
F601
0.2A/24V
C
LND616
N.C.
D608
01ZA8.2(TPL3)
D602
CL-200IR-X-TU-BC
(IR)
LND617
S601
8
7
1
2
INFINITY
MAN
4
5
6
D
D609
01ZA8.2(TPL3)
FOCUS
AUTO
9
S603
10
S604
R601
27k
(FLASH)
R602
8200
S602
S603
R604
1608
FADER
D603
TLSU1002(TPX1,SONY)
CAMERA
RECORDING
R607
1k
S604
E
R606
330
PUSH AUTO
1.6
Q601
UN9211J-(K8).SO
LED DRIVE
D601
TLOU1008(T05,SOY)
(FLASH)
0
IC601
REMOTE COMMANDER
RECEIVER
LND619
D605
01ZA8.2(TPL3)
R605
47
3
F
1
IC601
SBX3055-01
D610
01ZA8.2(TPL3)
LND618
4.5
05
C601
10u
4
2
4.5
D606
MA2S111-(K8).SO
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
4-79
Les composants identifiés par une marque 0 sont
critiques pour la sécurité. Ne les remplacer que
par une piéce portant le numéro spécifié.
4-80
FP-504
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
For Schematic Diagram
• Refer to page 4-121 for printed wiring board.
1
2
FP-495 FLEXIBLE BOARD FP-497 FLEXIBLE BOARD
For Schematic Diagram
• Refer to page 4-122 for printed wiring board.
3
4
5
1
FP-495 FLEXIBLE BOARD
2
4
3
5
6
FP-497 FLEXIBLE BOARD
A
A
B
1 GND
S002
(PANEL REVERSE)
B
2 GND
3 P_REVERSE
4 P_OPEN
CK-116
CN5206
(PAGE 4-70)
INTELLIGENT
ACCESSORY
SHOE
5 GND
S001
(PANEL OPEN)
6 GND
C
C
LND001
SHOE_GND
1 SHOE_UNREG_GND
LND002
SHOE_MT_GND
2 SHOE_UNREG_GND
LND003
SHOE_MIC_L
3 SHOE_UNREG_GND
LND004
SHOE_CONT_AD
4 SHOE_MT_GND
LND005
SHOE_MIC_GND
5 SHOE_MT_GND
LND006
CTS
6 SHOE_MIC_L
LND007
EXT_STRB_ON
7 SHOE_CONT_AD
LND008
RTS
8 SHOE_MIC_GND
LND009
SHO_ID2
LND010
RXD
10 SHOE_MIC_GND
LND011
SHO_ID1
11 SHOE_MIC_GND
LND012
TXD
12 CTS(HDS)
LND013
LANC_SIG
13 STBY_ON/SHOE_MIC_R
LND014
PRT_UNREG
14 RTS(SCK)
LND015
SHOE_UNREG
15 SHOE_ID2
9 SHOE_MIC_GND
05
DB-014 (8/9)
CN7205
(PAGE 4-61)
16 RXD
17 SHOE_ID1
18 TXD
19 LANC_SIG
20 BT_LED_A
D
21 BT_LED_K
22 PRT_HEAD_UNREG
23 PRT_HEAD_UNREG
24 SHOE_UNREG
25 SHOE_UNREG
D001
CL-190HBF-X-T
26 BT_ON
(Note)
E
Note: Although parts are mounted
on the board, they are not
used in TRV940/TRV940E.
27 REG_GND
S001
S001
NETWORK
D001
(BLUETOOTH)
(Note)
TRV-950/TRV950E
05
1
2
3
4
5
1
FP-500 FLEXIBLE BOARD
3
5
4
6
7
FP-503 FLEXIBLE BOARD
PRINTED WIRING BOARD is omitted.
A
2
A
FP-503 FLEXIBLE BOARD is replaced as block,
so that PRINTED WIRING BOARD is omitted.
1
3
D501
RLD65MQT1-02B
(LASER UNIT)
(Note 1)
B
1
LD_EVR
2
PD_OUT
3
MTGND
MA-410
4
PHOTO_TR_C (N.C.)
CN5903
(PAGE 4-67)
5
PHOTO_TR_E (N.C.)
6
N.C.
2
B
10P
VSS
1
1
VSS
VCC
2
2
VCC
SCLK
3
3
SCLK
INS
4
4
N.C
VC-288 (16/17)
DIO
5
5
INS
CN1009
(PAGE 4-44)
VCC
6
6
N.C
BS
7
7
DIO
05
C
(Note 1) Be sure to read “SERVICE NOTE” on page 1-3
when replacing the laser unit (D501).
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
FP-495, FP-497, FP-500, FP-503
4-81
Les composants identifiés par une marque 0 sont
critiques pour la sécurité. Ne les remplacer que
par une piéce portant le numéro spécifié.
VSS
8
8
VCC
ACCESS_LED
9
9
BS
MS_LED_VCC
10
10
VSS
D001
(MS ACCESS)
D
05
4-82
MEMORY
STICK
MS
SOCKET
MEMORY STICK
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
FP100, FP-102, FP-228 FLEXIBLE BOARD
For Schematic Diagram
• Refer to page 4-123 for printed wiring board.
2
1
3
4
5
6
7
B
FP-228
FLEXIBLE BOARD
M903
LOADING
MOTOR
M
DEW
SENSOR
LM_LOAD
1
LM_LOAD
2
LM_UNLOAD
3
LM_UNLOAD
4
DEW+
5
DEW-
6
MODE A
7
MODE B
8
C
MODE C
S902
MODE
SWITCH
SW_COM/SW_GND
-
+
G
H901
S REEL
SENSOR
27
25
Vcc
27P
24
TAPE_END
G
26
23
SREEL+
+
TAPE_TOP
22
SREEL-
-
TOP/END_GND
21
18
HALL_GND
17
CHIME_VDD
20
16
CHIME_SDA
CN901
4P
FLEXIBLE BOARD
TREEL-
15
CHIME_SCK
FLEXIBLE BOARD
FP-102
19
14
XREC_PROOF
D901
(TAPE LED)
D
Vcc
H902
T REEL
SENSOR
S903
(CC DOWN)
FP-100
TREEL+
13
MIC/REC_SW_GND
9
10
HALL_VCC
12
TAPE_LED_A
8
11
7
XMODE_SW_B
TAPE_LED_K
6
XMODE_SW_A
XCCDOWN_SW
5
DEW-
9
4
DEW+
10
3
LM_UNLOAD
SW_COM/SW_GND
2
LM_UNLOAD
XMODE_SW_C
1
LM_LOAD
A
LM_LOAD
VC-288 (12/17) CN1006 (PAGE 4-36)
Q902
TAPE TOP
SENSOR
Q901
TAPE END
SENSOR
S901
(REC PROOF)
05
4-83
4-84
FP-100, FP-102, FP-228
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
1
2
4
3
CONTROL SWITCH BLOCK
(CF-1870)
A
1
6
5
CONTROL SWITCH BLOCK (CF-1870) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
2
3
4
CONTROL SWITCH BLOCK
(PS-1870)
CONTROL SWITCH BLOCK (PS-1870) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
A
S004
MEMORY/
NETWORK
6
B
DB-014
(8/9)
B
RV001
(ZOOM)
W
CN7201
(PAGE 4-61)
T
S001
PHOTO
LND006
XPHOTO_STBY
LND005
XCAM_MODE_SW
LND004
XVTR_MODE_SW
LND003
XS/S_SW
LND002
GND
LND001
XEJECT_SW
4
3
2
S003
VCR
S001
START/STOP
1
8
(PHOTO REC)
GND
LND001
GND
LND002
XPHOTO_REC
LND003
XPHOTO_FREEZE
LND004
D_2.8V
LND005
N.C.
LND006
ZOOM_VR_AD
LND007
D
C
DB-014 (8/9)
OPEN/
05
CN7200
(PAGE 4-61)
LND008
GND
1
05
1
2
3
4
CONTROL SWITCH BLOCK
(KP-1870)
A
6
5
CONTROL SWITCH BLOCK (KP-1870) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
1
B
CK-116
CN5205
(PAGE 4-70)
LND001
GND
LND002
KEY_AD5BACK
LND003
KEY_AD5IN
LND004
S007
SEL/PUSH EXEC
MENU
LND005
DIAL_A
LND006
DIAL_B
LND007
GND
LND008
EXECUTE
8
C
A
1
R001
1200
B
2
S001
MENU
A
1
B
2
S002
D
AUDIO.LEVEL
R002
1500
A
1
B
2
S003
EXPOSURE
R004
3900
R003
2200
A
1
B
2
A
1
B
2
S004
S005
WHT.BAL
SHUTTER
SPEED
A
1
B
2
S006
PROGRAM,AE
05
CF-1870, KP-1870, PS-1870
S002
CAMERA
1
5
(PHOTO FREEZE)
C
5
4-85
4-86
EJECT
S005
DCR-TRV940/TRV940E/TRV950/TRV950E
COVER
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR WIRING BOARDS
(In addition to this, the necessary note is printed in each block)
(For printed wiring boards)
: Uses unleaded solder.
•
•
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
• Chip parts.
Transistor
B
4-87
Diode
6 5 4 4 5 6 5
C
E
4 4
3
5
1 2 3 3 2 1 1 2 3 3 2 1
1
3
3
1 23
2
1 2
1 2
1 3
4
1
2 3
4
4
3
3
4
5 4 3 3 4 5 2
1
4
3 2
1 1
2
2
1
2 2
1 6 54
DCR-TRV940/TRV940E/TRV950/TRV950E
COVER
4-3. PRINTED WIRING BOARDS
Link
CD-389 BOARD (SIDE A)
JK-222 BOARD (SIDE B)
CD-389 BOARD (SIDE B)
PD-168 BOARD
SE-132 BOARD
LB-080 BOARD
MA-410 BOARD
FP-504 FLEXIBLE BOARD (SIDE A)
CK-116 BOARD (SIDE A)
FP-504 FLEXIBLE BOARD (SIDE B)
CK-116 BOARD (SIDE B)
FP-495, FP-497 FLEXIBLE BOARD
JK-222 BOARD (SIDE A)
FP-100, FP-102, FP-228 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
CIRCUIT BOARDS LOCATION
WAVEFORMS
FLEXIBLE BOARDS LOCATION
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
CD-389 (CCD IMAGER)
For Printed Wiring Board.
:Uses unleaded solder.
•
• CD-389 board is six-layer print board. However, the patterns of
layers 2 to 5 have not been included in the diagram.
• There are a few cases that the part isn't mounted in this model is
printed on this diagram.
• See page 4-131 for printed parts location.
CD-389 BOARD (SIDE A)
A
B
1-685-541- 12
R102
L100
A C114
C110
12
C111
7
8
8
15
IC104
13
18
1
7
7
LND101
L104
LND100
C103
14
C124
C101
L103
R101
C127
R100
C126
P
A
8
C123
C113
+
17
16
R108
14
14
14
C106
C131 A
C122
Q102
1
+
R109
7
B
C
E
5
9
7
C125
IC101
IC103
C100
L101
R103
C120 C119
C121
D
8
4
14
+
8
(G)
8
C102
L105
R106
14
8
C107
R105
10
R107
P
E
R104
IC102
C
B
C116
IC100
C
6
3
E
1
1
C109
+
L102
R111
Q101
11
B
7
Q100
R110
C115
2
1
14
IC105
1
C105
C108
(R)
C112
(B)
7
+
P
1
C132
C117
C104
+
C
C118
C130
C129
C128
05
1
2
4-89
3
4
5
6
4-90
7
CD-389 (SIDE A)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
CD-389 BOARD (SIDE B)
60
2
CN100
1
59
A
B
1-685-541-
12
C
D
05
7
CD-389 (SIDE B)
6
5
4-91
4
3
2
4-92
1
Printed wiring boards of the VC-288, DB-014 boards are not shown.
Pages from 4-93 to 4-100 are not shown.
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
SE-132 (PITCH/YAW SENSOR)
For Printed Wiring Board.
:Uses unleaded solder.
•
• SE-132 board is six-layer print board. However, the patterns of
layers 2 to 5 have not been included in the diagram.
• There are a few cases that the part isn't mounted in this model is
printed on this diagram.
• See page 4-136 for printed parts location.
SE-132 BOARD (SIDE A)
C4001
C4012
R4010 R4011
SE4002
B
E
C
C4014
Q4001
P
+
B
C
E
Q4002
A
C4010
+
P
SE4001
L4001
C4002
P
C4011
C4009
+
1-685-543-
12
B
1
05
2
3
4
R4001
R4004
C4007
R4012
R4007
B
R4005
SE-132 BOARD (SIDE B)
C4003
C4005
C4016
20
2
1
C4015
11
IC4001
05
4-101
1
2
C4006
R4002
C4004
C4008
C4013
R4003 10
R4006
R4008
R4009
1
1-685-543-
8
A
7
CN4005
3
12
4
4-102
SE-132
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
Suffix number qa
MA-410 BOARD (SIDE A)
MA-410
(MIC AMP, AF LASER CONTROL)
MIC
(PLUG IN POWER)
For Printed Wiring Board.
:Uses unleaded solder.
•
• MA-410 board is four-layer print board.
However, the patterns of layers 2 to 3 have
not been included in the diagram.
• There are a few cases that the part isn't
mounted in this model is printed on this diagram.
• See page 4-136 for printed parts location.
4
1
MA-410 BOARD (SIDE B)
LND592
C5901
1
FB5902
R5903
R5904
C5915
C5914
37
48
1
25
C5928
6
R5927
24
13
R5943
1
C5941
C5939
A2
R5938
+
R5942
C5935
C5940
C5936
C5938
C5930
8
1-685-546-
11
CN5904
C
1
05
2
3
05
4
4
B
CN5903
C5929
P
1-685-546-
FB5901
D5902
R5922
C5927
R5928
R5936
R5940
33
K
2
R5919
CN5906
1
K
C5923
R5916
R5941
R5937
A
R5912
C5924
L5901
3
A
K
A
36
C5918
R5923
R5920
R5925
IC5901
16
2
Q5904
C5931
Q5905
R5932
4
K
K
VDR592
R5921
R5924
5
C5922
R5917
C5926
K
C5919
D5901 D5903
R5918
C5925
12
R5930
R5929
B
C5932
R5939
C5933
C5907
C5913
C5905
C5917
R5911
R5907
C5906
1
1
R5915
R5952
CN5905
2
C5937
C5920
R5910
R5951
C
P
1
R5934
R5935
R5950
+
R5931
+
R5946
R5933
R5926
IC5902
B
R5948
Q5906
C5942
C5921
E
Q5903
R5945
Q5901
R5949
R5944
C5909
R5909
R5914
R5947
C5943
C5916
C5934
R5953
C5911
R5908
Q5902
A
+
+
P
R5913
C5910
P
C5912
R5905
1
5
2
C5902 VDR591
2
C5903
CN5902
R5901
CN5901
C5908
C5904
R5902
2
A
LND591
R5906
J5901
3
2
C
11
1
Suffix number qs
MA-410 BOARD (SIDE A)
MIC
(PLUG IN POWER)
4
1
MA-410 BOARD (SIDE B)
LND592
R5906
+
C5903
FB5902
C5914
37
48
FB5901
2
1
R5918
R5919
4-103
B
CN5903
5
6
R5928
C5928
R5923
25
R5922
C5927
24
12
C5929
P
+
C5941
C5935
C5939
C5936
R5938
C5930
C5938
R5920
R5925
A
R5940
1-685-546-
8
12
1-685-546-
33
CN5904
2
K
C5923
R5916
R5921
C
MA-410
A
D5902
1
1
K
CN5906
1
05
A
K
R5943
R5937
R5936
R5912
C5924
R5942
3
K
K
36
C5918
C5940
2
IC5901
13
Q5905
4
Q5904
K
C5919
D5901 D5903
VDR592
L5901
5
R5932
R5924
C5932
C5922
R5917
C5926
C5931
B
C
E
P
R5939
C5933
C5906
R5907
R5927
C5908
C5909
C5917
1
1
R5915
R5911
16
+
R5951
CN5905
2
C5937
R5910
R5952
A2
R5935
R5950
C5920
C5921
1
R5934
R5905
C5905
C5942
C5925
+
R5946
R5933
R5931
Q5906
R5929 R5930
R5926
IC5902
B
R5948
Q5901
Q5903
R5947
C5943
C5934
R5949
R5945
C5910
C5908
+
R5909
R5914
R5944
C5911
R5945
R5953
C5916
C5944
Q5902
C5913
P
P
C5912
R5913
C5902 VDR591
1
R5903
2
1
A
R5901
2
C5901
R5904
CN5902
C5907
CN5901
R5941
C5904
R5902
2
A
LND591
C5915
J5901
3
4
05
4
3
2
4-104
1
C
12
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
CK-116 (CONTROL SWITCH)
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or eqivalent type.
For Printed Wiring Board.
CK-116 BOARD (SIDE A)
DISPLAY/
TOUCH PANEL
A
REW
S5207
-
S5116
S5215
PLAY
FF
S5208
S5209
STOP
REC
VOLUME
+
S5214
PAUSE
S5210
B
AUDIO DUB
S5206
S5217
BT5201
BATTERY,
LITHIUM SECONDARY
C
DATA CODE
S5203
S5211
S5212
COLOUR
BAR
CUSTOM
PRESET
S5213
S5220
S5202
01
52
BT
1
D
LN5201
ZEBRA
RESET
OFF
70
100
S5221
CN5201
LN5204
LN5202
AUTO LOCK
RELEASE
AUTO
LOCK
E
HOLD
LN5203
20
:Uses unleaded solder.
•
• CK-116 board is four-layer print
board. However, the patterns of layers 2 to 3 have not been included in
the diagram.
• There are a few cases that the part
isn't mounted in this model is printed
on this diagram.
• See page 4-136 for printed parts location.
BACK LIGHT
+
SPOT LIGHT
EDIT SEARCH
S5201
S5219
S5218
S5204
S5205
1-685-544-
F
05
1
2
4-105
3
4
5
11
6
4-106
12
7
CK-116 (SIDE A)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
CK-116 BOARD (SIDE B)
1
D5208
2
A
CN5204
K
K
A
R5219 R5223
R5228
R5233
R5218
R5236
R5227
R5222
A
D5201
R5210
1
K
K
CN5205
8
K
R5214
K A
A
K
K
R5232
D5205
K
R5238
B
A
R5212
R5203
D5206
D5209
R5242
R5239
R5240
R5241
C
R5215
R5202
R5204
R5211
R5208
R5237
C5203
R5213
R5235
R5217
R5221
R5207
D5207
CN5206
A
K
K
6
D
1
R5205
C5202
R5243
10
+
R5206
BB
C5201
60
2
CN5203
CN5202
1
59
R5225
1
R5244
R5230
E
R5226
R5209
R5216
R5220
R5224
A
K
D5204
D5202
R5231
K
K
A
R5229
K
K
R5234
A
F
D5203
1-685-54405
CK-116 (SIDE B)
4-107
7
6
5
4
3
2
4-108
1
11
12
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
JK-222 (AV IN/OUT, DV/USB CONNECTOR)
For Printed Wiring Board.
JK-222 BOARD (SIDE A)
A
LND461
7
:Uses unleaded solder.
•
• JK-222 board is six-layer print board.
However, the patterns of layers 2 to
5 have not been included in the diagram.
• There are a few cases that the part
isn't mounted in this model is printed
on this diagram.
• See page 4-136 for printed parts location.
D402
A
B
K
K
C
D
LND472
LND471
LND470
LND469
LND468
LND467
LND466
LND465
1
8
E
1-685-542-
12
F
G
05
1
2
4-109
3
4
5
6
7
8
4-110
9
10
JK-222 (SIDE A)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
AUDIO/VIDEO
JK-222 BOARD (SIDE B)
ID-2
1
(HEAD PHONE)
J403
J404
4
FB403
R406
FB407
VDR408
VDR404
VDR407
2
R411
VDR406
1
FB404
A
FB406
R409
3
LND451
LND452
LND453
LND454
LND455
LND456
LND457
LND462
S VIDEO ID-2
VDR409
R408
R403
LF403
5
7
VDR401
LF401
LF402
LND460
8
VDR403
CN402
R401
1
(USB)
J401
R404
B
R407
6
R402
VDR402
LND458
A
K
D403
LND473
FB401
VDR405
FB405
8
6
J402
LANC
CN401
DV
A
D401
2
K
4
7
5
1
C
K
FB402
R410
3
LND459
D
E
LND424
LND426
LND428
LND430
LND432
LND434
LND436
LND438
LND440
LND442
LND444
LND446
LND448
LND450
LND401
LND403
LND405
LND407
LND409
LND411
LND413
LND415
LND417
LND419
LND422
05
JK-222 (SIDE B)
LND425
LND427
LND429
LND431
LND433
LND435
LND437
LND439
LND441
LND443
LND445
LND447
LND449
1
F
27
G
LND402
LND404
LND406
LND408
LND410
LND412
LND414
LND416
LND418
LND421
1
21
12
1-685-542-
10
9
4-111
8
7
6
5
4
3
4-112
2
1
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
PD-168 (LCD DRIVER, TIMING GENERATOR, BACKLIGHT)
For Printed Wiring Board.
:Uses unleaded solder.
•
• PD-168 board is four-layer print board. However, the patterns of
layers 2 to 3 have not been included in the diagram.
• There are a few cases that the part isn't mounted in this model is
printed on this diagram.
• See page 4-136 for printed parts location.
PD-168 BOARD (SIDE A)
R5805
CN5802
A
L5701
1
1
R5717
25
C5714
36
R5710
IC5701
5
4
12
13
R5721
C5805
C5806
C5807
1
E C B
R5804
1
5
C5720
C5721
B
C5801
8
1
9
32
L5704
IC5801
E C B
Q5802
Q5801
C5723
CN5803
R5803
C5724
R5802
C5719
D5701
A C5722 +
L5801
R5801
R5705
A C5716 +
24
C5718
C5802
C5703
D5702
C5803
B
25
24
6
Q5701
R5706
C5717
L5802
L5705
A C5808 +
R5732
+
R5702
C5702
R5707
C5708
R5714
R5736
R5737
C5713
R5712
37
E C B
R5719
R5711
9
24
R5709
36
C5710
C5709
IC5702
R5727
2
R5708
3
+ C5711 A
48
R5713
1
1
A C5707 +
1
B
37
48
12
13
C5701
L5703
8
CN5701
R5703
1
C5712
R5722
C5715
B
C5804
R5701
C
C5705
C5704
E
C5706
7
L5702
C5726
C5727
Q5702
C
CN5806
10
R5806
A
20
PD-168 BOARD (SIDE B)
LND581
16
17
C
25
24
7
2
CN5805
CN5804
1
1-685-54705
1
2
3
4-113
1-685-547-
21
4
11
11
12
05
4
3
2
4-114
12
1
PD-168
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
LB-080 (EVF, EVF BACKLIGHT)
For Printed Wiring Board.
:Uses unleaded solder.
•
• LB-080 board is four-layer print board. However, the patterns of
layers 2 to 3 have not been included in the diagram.
• There are a few cases that the part isn't mounted in this model is
printed on this diagram.
LB-080 BOARD (SIDE B)
LB-080 BOARD (SIDE A)
Q6101
R6107
LF6101
C6101
1
R6104
16
TH6101
Q6102
R6102
D6102
(BACK LIGHT)
R6101
CN6101
R6106 R6103
3
4
2
D6101
(TALLY)
1
5
R6105
05
LB-080
4-115
1-685-545-
11
12
05
C6102
20
1
IC6101
CN6102
1-685-545-
4-116
11
12
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
FP-504 FLEXIBLE
For Printed Wiring Board.
• See page 4-137 for printed parts location.
FP-504 FLEXIBLE BOARD (SIDE A)
A
D605
K
B
D610
K
A
K
A
K
D609
K
S603
LND618
LND619
LND613
LND615
LND612
LND611
LND607
LND606
LND604
LND603
LND601
LND602
LND605
LND610
LND614
LND609
LND608
LND616
R604
A
K
FADER
S603, D601
A
S601
R602
D601
S602
S604
R601
K
(FLASH)
Q601
R606
FOCUS
PUSH AUTO
AUTO
MAN
R603
INFINITY
F601
R607
C
D
1-685-300-
12
D607
K
K
D606
A
IC601
R605
PH601
LND617
D603
K
K
A
E
C601
D608
D603
(CAMERA RECORDING)
D602
D602
(IR)
PH602
05
1
2
3
4-117
4
5
6
7
4-118
FP-504 (SIDE A)
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
FP-504 FLEXIBLE BOARD (SIDE B)
A
B
1-685-30012
C
D
E
05
FP-504 (SIDE B)
7
6
4-119
5
4
3
2
4-120
1
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
FP-495, FP-497 FLEXIBLE
FP-497 FLEXIBLE BOARD
FP-495 FLEXIBLE BOARD
1
1
27
TRV950/950E
S001
D001
(BLUETOOTH)
NETWORK
A
S001
D001
K
1-685-295-
11
05
(PANEL REVERSE)
S002
LND015
LND014
LND013
LND012
LND011
LND010
LND009
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
6
(PANEL OPEN)
1-685-293-
11
INTELLIGENT
ACCESSORY
SHOE
S001
05
4-121
4-122
FP-495, FP-497
DCR-TRV940/TRV940E/TRV950/TRV950E
4-2. SCHEMATIC DIAGRAMS
COVER
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
FP-100, FP-102, FP-228 FLEXIBLE
27
1
Q902
TAPE TOP
SENSOR
FP-102 FLEXIBLE BOARD
10
1
11
1-677-085D901
(TAPE LED)
S903
(CC DOWN)
S901
(REC PROOF)
CN901
Q901
TAPE END
SENSOR
H902
T REEL
SENSOR
H901
S REEL
SENSOR
1
FP-100 FLEXIBLE BOARD
M903
LOADING
MOTOR
M
11
1-677-084DEW
SENSOR
11
1-677-049-
FP-228
FLEXIBLE BOARD
05
S902
MODE SWITCH
FP-100, FP-102, FP-228
4-123
4-124
10
DCR-TRV940/TRV940E/TRV950/TRV950E
CD-389 BOARD SIDE A
COVER
CD-389 BOARD SIDE B
4-4. WAVEFORMS
CD-389 BOARD (1/2)
6
1
7.6 Vp-p
100 mVp-p
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
IC105 1, 4 REC
2
IC102 5 REC
7
7.6 Vp-p
7.6 Vp-p
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
IC105 2, 3 REC
3
IC100 1, 4 REC
8
5.1 Vp-p
7.6 Vp-p
30 nsec (TRV940/TRV950)
37 nsec (TRV940E/TRV950E)
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
IC105 qa, qs REC
4
IC100 2, 3 REC
9
5.1 Vp-p
3.6 Vp-p
33 MHz (TRV940/TRV950)
27 MHz (TRV940E/TRV950E)
30 nsec (TRV940/TRV950)
37 nsec (TRV940E/TRV950E)
IC105 q; REC
IC100 qa, qs REC
5
q;
3.6 Vp-p
310 mVp-p
33 MHz (TRV940/TRV950)
27 MHz (TRV940E/TRV950E)
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
IC105 8 REC
IC100 q; REC
4-125
CD-389 (1/2)
DCR-TRV940/TRV940E/TRV950/TRV950E
COVER
CD-389 BOARD SIDE A
CD-389 BOARD SIDE B
CD-389 BOARD (2/2)
qa
qh
3.6 Vp-p
360 mVp-p
33 MHz (TRV940/TRV950)
27 MHz (TRV940E/TRV950E)
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
IC100 8 REC
IC101 q; REC
qs
qj
200 mVp-p
470 mVp-p
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
IC103 5 REC
IC101 8 REC
qd
qk
260 mVp-p
7.6 Vp-p
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
IC101 1, 4 REC
IC104 5 REC
qf
7.6 Vp-p
44 µsec (TRV940/TRV950)
54 µsec (TRV940E/TRV950E)
IC101 2, 3 REC
qg
5.1 Vp-p
30 nsec (TRV940/TRV950)
37 nsec (TRV940E/TRV950E)
IC101 qa, qs REC
CD-389 (2/2)
4-126
Waveforms of the VC-288, DB-014 boards are not shown.
Pages 4-127 to 4-129 are not shown.
DCR-TRV940/TRV940E/TRV950/TRV950E
PD-168 BOARD
COVER
PD-168 BOARD
6
1
540 mVp-p
4.2 Vp-p
H
2H
IC5701 rk REC/PB
IC5701 wf REC/PB
7
2
2.8 Vp-p
480 mVp-p
H
H
IC5701 rj REC/PB
IC5702 1 REC/PB
8
3
2.8 Vp-p
440 mVp-p
V
H
IC5701 rh REC/PB
IC5702 rk REC/PB
9
4
3.8 Vp-p
3.8 Vp-p
22.2 MHz
2H
IC5701 w; REC/PB
IC5702 wh REC/PB
5
3.6 Vp-p
2H
IC5701 ws REC/PB
PD-168
4-130
DCR-TRV940/TRV940E/TRV950/TRV950E
COVER
4-3. PRINTED WIRING BOARDS
no mark : side A
* mark : side B
4-5. MOUNTED PARTS LOCATION
CD-389 BOARD
C102
C103
C104
C105
C106
C107
C108
C109
C110
C111
C112
C113
C114
C115
C116
C117
C118
C119
C120
C121
C122
C123
C124
C125
C126
C127
C128
C129
C130
C131
* CN100
IC100
IC101
IC102
IC103
IC104
IC105
L100
L101
L102
L103
L104
L105
Q100
Q101
Q102
R100
R101
R102
R103
R104
R105
R106
R107
R108
R109
R110
R111
D-4
D-6
C-1
C-1
D-3
C-6
C-1
C-4
C-6
C-6
C-4
D-3
C-7
C-4
C-4
C-6
C-6
D-1
D-1
D-1
D-2
D-4
D-7
D-2
D-4
D-6
D-4
D-6
C-1
D-2
A-4
D-4
D-6
D-1
D-4
D-6
D-1
C-1
D-3
C-6
D-4
D-6
D-2
C-3
C-6
D-1
D-4
D-6
C-1
D-1
C-3
C-6
D-1
C-4
C-7
D-1
C-4
C-6
4-131
CD-389
Mounted parts location of the VC-288, DB-014 boards are not shown.
Pages 4-132 to 4-135 are not shown.
DCR-TRV940/TRV940E/TRV950/TRV950E
4-3. PRINTED WIRING BOARDS
COVER
(Note: C5944 and C5945 are mounted on the
board with suffix number 12)
SE-132 BOARD
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
C4001
C4002
C4003
C4004
C4005
C4006
C4007
C4008
C4009
C4010
C4011
C4012
C4014
C4015
CN4005
IC4001
L4001
Q4001
Q4002
R4001
R4002
R4003
R4004
R4005
R4006
R4007
R4009
R4010
R4011
SE4001
SE4002
A-2
A-3
A-2
A-2
A-2
A-2
A-2
A-2
B-2
A-2
B-2
A-2
A-1
A-1
A-1
A-2
A-1
A-1
A-1
A-2
A-2
A-2
A-2
A-2
A-2
A-1
A-1
A-1
A-1
A-2
A-3
MA-410 BOARD
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
C5901
C5905
C5906
C5907
C5908
C5909
C5910
C5911
C5912
C5913
C5914
C5915
C5917
C5918
C5920
C5921
C5922
C5923
C5924
C5925
C5926
C5927
C5928
C5929
C5930
C5931
C5932
C5933
C5934
C5935
C5936
C5937
C5938
C5939
C5940
C5941
C5944
C5945
CN5901
CN5902
CN5903
CN5904
CN5905
CN5906
D5903
FB5901
FB5902
IC5901
IC5902
J5901
L5901
Q5901
Q5902
Q5903
Q5904
Q5905
Q5906
R5901
R5902
R5903
R5904
R5905
R5906
R5907
R5908
R5909
R5910
R5911
R5912
R5914
R5915
R5916
R5917
R5918
R5919
R5920
R5921
R5922
R5923
R5924
R5925
R5926
R5927
R5928
A-2
A-2
B-2
A-1
A-2
A-2
A-2
A-3
A-2
A-2
A-2
A-2
B-2
B-1
B-2
B-2
B-2
B-1
B-2
B-3
B-2
B-1
B-1
B-1
B-2
B-3
B-3
B-2
B-3
B-2
B-2
B-2
B-1
B-1
B-1
B-1
A-3 (Note)
A-3 (Note)
A-3
A-2
B-1
C-1
B-4
B-3
B-1
B-1
A-1
B-2
B-4
A-1
B-2
B-3
B-3
B-3
B-3
B-3
B-3
A-1
A-4
A-1
A-1
A-2
A-2
B-1
A-2
B-3
B-3
B-3
B-1
B-3
B-3
B-1
B-2
B-1
B-1
B-3
B-2
B-1
B-1
B-3
B-3
B-4
B-1
B-2
*
*
*
*
*
*
*
*
R5929
R5930
R5931
R5933
R5934
R5935
R5936
R5937
R5938
R5939
R5940
R5941
R5943
R5944
R5946
R5947
R5948
R5949
R5951
R5952
R5953
VDR591
VDR592
SE-132, MA-410, CK-116, JK-222, PD-168
B-4
B-4
B-2
B-2
B-2
B-2
B-4
B-4
B-1
B-4
B-4
B-1
B-1
B-3
B-3
B-3
B-3
B-3
B-3
B-3
B-3
A-1
B-1
CK-116 BOARD
JK-222 BOARD
BT5201
* C5201
* C5202
CN5201
* CN5202
* CN5203
* CN5204
* CN5205
* CN5206
* D5201
* D5202
* D5203
* D5204
* D5205
* D5206
* D5207
* D5208
* D5209
* R5208
* R5209
* R5210
* R5211
* R5212
* R5213
* R5214
* R5215
* R5216
* R5217
* R5218
* R5219
* R5220
* R5221
* R5222
* R5223
* R5224
* R5225
* R5226
* R5227
* R5228
* R5229
* R5230
* R5231
* R5232
* R5233
* R5234
* R5235
* R5236
* R5237
* R5238
* R5239
* R5240
* R5243
* R5244
S5116
S5201
S5202
S5203
S5204
S5205
S5206
S5207
S5208
S5209
S5210
S5211
S5212
S5213
S5214
S5215
S5217
S5218
S5219
S5220
S5221
* CN401 C-6
* CN402 B-3
* D401
C-3
D402
B-3
* FB401 C-3
* FB402 C-3
* FB403 A-3
* FB404 A-2
* FB405 C-3
* FB406 A-1
* FB407 A-1
* J401
B-6
* J402
C-3
* J403
A-2
* J404
A-1
* LF401 A-3
* LF402 A-3
* R401
B-6
* R402
B-5
* R403
B-6
* R404
B-3
* R406
A-2
* R407
B-3
* R408
B-1
* R409
A-2
* R410
C-6
* R411
A-2
* VDR401 B-5
* VDR402 B-6
* VDR403 B-6
* VDR404 A-2
* VDR405 C-3
* VDR406 A-2
* VDR407 A-1
* VDR408 A-1
* VDR409 A-1
4-136
D-3
D-3
D-3
E-1
E-1
E-2
A-6
C-7
D-1
C-6
F-3
F-3
E-5
C-6
C-6
D-2
A-5
C-6
C-6
E-2
C-6
C-5
C-5
C-5
C-5
C-6
E-2
D-5
B-4
A-6
E-2
D-5
B-5
A-6
E-2
E-6
E-4
B-6
A-5
E-2
E-6
E-4
C-6
B-4
F-2
D-5
B-4
C-7
C-5
C-6
C-7
D-2
E-2
A-5
E-7
D-6
C-5
F-4
F-4
C-5
B-4
B-5
B-6
B-7
C-6
C-7
C-6
A-7
A-6
C-4
F-1
F-2
C-7
D-5
no mark : side A
* mark : side B
PD-168 BOARD
C5701
C5702
C5703
C5704
C5705
C5706
C5707
C5708
C5709
C5710
C5711
C5712
C5713
C5714
C5715
C5716
C5717
C5718
C5719
C5720
C5721
C5722
C5723
C5724
C5726
C5727
C5801
C5802
C5803
C5805
C5807
C5808
CN5701
CN5802
CN5803
CN5804
CN5805
CN5806
D5701
D5702
IC5701
IC5702
IC5801
L5701
L5702
L5703
L5704
L5705
L5801
L5802
Q5701
Q5702
Q5801
Q5802
R5701
R5702
R5703
R5705
R5706
R5707
R5708
R5709
R5710
R5711
R5712
R5713
R5714
R5717
R5719
R5721
R5722
R5727
R5732
R5736
R5737
R5801
R5802
R5803
R5804
R5805
A-4
A-4
C-3
A-3
A-3
A-3
B-3
B-3
B-3
B-4
B-4
B-4
B-3
B-3
B-4
C-3
B-2
C-2
B-4
B-3
B-3
C-3
C-1
C-1
B-2
B-2
B-4
C-2
C-2
C-3
C-1
C-3
B-1
A-2
C-1
C-4
C-2
A-4
C-3
C-2
B-4
B-2
C-4
A-4
B-3
B-4
C-3
B-2
C-2
C-3
B-3
A-3
C-1
C-3
B-4
A-4
A-4
C-3
B-3
B-4
B-3
B-3
B-3
B-3
B-3
B-3
B-3
B-2
B-2
C-3
B-3
B-2
B-2
B-2
C-2
B-4
B-4
C-3
C-3
A-4
DCR-TRV940/TRV940E/TRV950/TRV950E
COVER
4-3. PRINTED WIRING BOARDS
no mark : side A
* mark : side B
FP-504 FLEXIBLE BOARD
C601
D601
D602
D603
D605
D606
D607
D608
D609
D610
F601
IC601
PH601
PH602
Q601
R601
R602
R603
R604
R605
R606
R607
S601
S602
S603
S604
E-5
B-1
E-6
E-6
B-1
E-6
D-2
E-3
B-4
B-3
C-4
D-6
E-2
E-3
C-1
C-2
B-1
C-4
B-1
E-5
C-1
C-1
B-2
B-3
B-1
B-4
4-137E
FP-504
DCR-TRV940/TRV940E/TRV950/TRV950E
SECTION 5
REPAIR PARTS LIST
COVER
5-1. EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they may
have some difference from the original one.
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
5-1-1. MAIN SECTION
ns: not supplied
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number specified.
• The mechanical parts with no reference number in
the exploded views are not supplied.
• Accessories are given in the last of the electrical
parts list.
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
EVF block
(See page 5-8.)
1
Stroboscope block
(See page 5-7.)
2
Cabinet (L) block
(See page 5-5.)
8
2
3
TRV950/
TRV950E
3
1
Battery panel block
(See page 5-9.)
1
4
ns
1
2
5
7
11
2
6
BT-003
2
9
2
1
9
2
10
TRV950/
TRV950E
1
1 MD block
(See page 5-10.)
Cabinet (R) block
(See page 5-3.)
F panel block
(See page 5-2.)
Ref. No.
1
Part No.
Description
1
2
3
4
5
3-989-735-01
4-974-725-01
3-713-791-31
3-076-240-01
X-3952-686-1
SCREW (M1.7), LOCK ACE, P2
SCREW (M1.7X2.5), P
SCREW (M1.7X6), TAPPING, P2
PLATE (B), MF KNOB RETAINER
FRAME ASSY, ST
Ref. No.
6
A-7067-302-A BT-003 BOARD, COMPLETE (TRV950/TRV950E)
7
8
9
10
11
5-1
Part No.
Description
1-685-290-11
3-073-941-01
3-055-573-21
3-389-523-28
3-076-834-01
FP-491 FLEXIBLE BOARD (TRV950/TRV950E)
STYLUS (TRV950/TRV950E)
SCREW (M1.7), LOCK ACE, P2
SCREW (LOCK ACE)
SHEET, AF BLIND
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-2. F PANEL BLOCK
ns: not supplied
56
60
61 (Note 1)
D501 (Note 1)
zB
(included in 53)
56
62
53
(including zA, zB)
59
56
59
66
63
56
54
56
55
56
59
64
65
10
-4
A
M
ns
MIC901
57
56
52
58
56
MIC902
zA
(included in 53)
67
52
51
68
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
(Note 1) Be sure to read “SERVICE NOTE” on page 1-3 when
replacing the laser unit (D501) and the FP-500 flexible
board.
Ref. No.
Part No.
Description
51
52
53
54
55
X-3952-617-1
3-076-349-01
A-7078-341-A
X-3952-621-1
3-076-276-01
GRILLE ASSY, MICROPHONE
SHEET, GRILLE
FP-504 FLEXIBLE BOARD, COMPLETE
PANEL ASSY, FRONT
COVER, MICROPHONE JACK
56
57
58
59
60
3-713-791-01
A-7078-336-A
3-076-348-01
4-974-725-01
X-3952-608-1
SCREW (M1.7X4), TAPPING, P2
MA-410 BOARD, COMPLETE
BRACKET, MA
SCREW (M1.7X2.5), P
BRACKET ASSY, AF LASER
61
1-685-298-11 FP-500 FLEXIBLE BOARD (Note 1)
Ref. No.
62
63
64
65
66
67
68
0 D501
MIC901
MIC902
5-2
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Part No.
Description
3-076-354-01
3-076-353-01
3-076-351-01
3-076-350-01
3-076-352-01
PLATE (A), MF KNOB RETAINER
SPRING, MF KNOB RETURN
RETAINER, MF KNOB
KNOB, MF
PLATE, ORNAMENTAL
X-3952-595-1
X-3952-594-1
1-804-531-11
1-542-312-11
1-542-312-11
CAP ASSY, LENS
HOOD ASSY
LASER UNIT (Note 1)
MICROPHONE (L-side)
MICROPHONE (R-side)
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-3. CABINET (R) BLOCK
ns: not supplied
106
106
109
6
-11
CK
106
110
%
ns
C
107
106
106
105
SP901
A
C
106
102
B
108
103
106
A
104
B
101
111
106
LCD block
(See page 5-4.)
! : Board
BT5201 (BATTERY, LITHIUM SECONDARY)
on the mount position. (See page 4-105.)
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or eqivalent type.
Ref. No.
Part No.
Description
101
101
102
103
104
X-3952-620-1
X-3952-643-1
3-051-840-01
3-076-305-01
3-958-217-01
CABINET (R) ASSY (TRV940/TRV950)
CABINET (R) ASSY (TRV940E/TRV950E)
SCREW, TRIPOD
BASE, TRIPOD TABLE
SCREW (M2)
105
106
3-076-299-01 CLAW, PANEL LOCK
3-989-735-51 SCREW (M1.7), LOCK ACE, P2
Ref. No.
5-3
Part No.
Description
107
108
109
110
111
3-062-194-01
X-3952-609-1
A-7078-338-A
1-477-338-11
3-076-344-01
SPACER, LOCK
LID ASSY, HINGE BLIND
CK-116 BOARD, COMPLETE
SWITCH BLOCK, CONTROL (KP1870)
CABINET (HINGE)
SP901
1-529-857-21 SPEAKER (1.6 cm)
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-4. LCD BLOCK
ns: not supplied
168
167
TA901
166
169
LCD901
ND901
164
165
ns
163
LCD902
162
161
8
-16
156
155
PD
157
156 153
156
154
155
156
160
158
156
152
155
151
159
170
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Ref. No.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Part No.
Description
Part No.
Description
151
152
153
154
155
3-076-448-01
X-3952-604-1
A-7078-342-A
3-076-447-01
3-989-735-51
COVER (FRONT), HINGE
HINGE ASSY
FP-495 FLEXIBLE BOARD, COMPLETE
COVER (REAR), HINGE
SCREW (M1.7), LOCK ACE, P2
163
164
165
166
167
X-3952-612-1
3-076-453-01
3-076-449-01
3-076-451-01
3-076-450-01
FRAME ASSY, P
SPRING (P), TORSION COIL
BUTTON, OPEN
CUSHION (L)
CUSHION (C)
156
157
158
159
159
4-974-725-01
1-961-814-11
1-961-815-11
X-3952-626-1
X-3952-642-1
SCREW (M1.7X2.5), P
HARNESS (PC-087)
HARNESS (PC-088)
P CABINET (C) ASSY (TRV950)
P CABINET (C) ASSY (TRV950E)
168
169
170
LCD901
3-076-452-01
3-076-446-01
3-076-631-01
1-804-599-21
159
159
160
0 161
162
X-3952-646-1
X-3952-661-1
A-7078-337-A
1-477-187-11
3-055-289-01
P CABINET (C) ASSY (TRV940E)
P CABINET (C) ASSY (TRV940)
PD-168 BOARD, COMPLETE
TRANSFORMER UNIT, INVERTER
HOLDER, LCD
PLATE (P), GROUND
CABINET (M), P
TAPE (H)
INDICATOR MODULE LIQUID CRYSTAL
(SERVICE)
LCD902 A-7096-726-A INDICATION LCD BLOCK ASSY
(CHARACTER DISPLAY)
(including FP-182 FLEXIBLE BOARD)
0 ND901
TA901
5-4
1-518-797-11 TUBE, FLUORESCENT,COLD CATHODE
1-477-189-11 PANEL, TOUCH
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-5. CABINET (L) BLOCK
ns: not supplied
Grip cabinet block
(See page 5-6.)
208
211
203 204
210
203
206
207
205
204
ns
203
204
SE-132
203
203
209
JK
-2
22
204
202
203
201
203
203
Ref. No.
Part No.
Description
201
202
203
204
205
3-076-343-01
A-7078-332-A
3-713-791-01
4-974-725-01
X-3952-622-1
BRACKET, JK
JK-222 BOARD, COMPLETE
SCREW (M1.7X4), TAPPING, P2
SCREW (M1.7X2.5), P
CABINET (L) ASSY (TRV940/TRV950)
205
206
X-3952-641-1 CABINET (L) ASSY (TRV940E/TRV950E)
3-076-309-01 BRACKET (FRONT), GRIP BELT
Ref. No.
5-5
Part No.
Description
207
208
209
210
211
X-3952-618-1
3-052-521-01
A-7078-339-A
X-3952-593-1
1-477-337-22
COVER ASSY, TERMINAL
CUSHION (2), PANEL
SE-132 BOARD, COMPLETE
CS FRAME ASSY
SWITCH BLOCK, CONTROL (PS1870)
(TRV950/TRV950E)
211
1-477-337-32 SWITCH BLOCK, CONTROL (PS1870)
(TRV940/TRV940E)
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-6. GRIP CABINET BLOCK
259
260
258
257
zC
(included in 251)
256
256
253
254
255
256
252
251
(including zC)
Ref. No.
Part No.
Description
251
251
252
252
253
1-685-299-11
1-685-299-21
X-3952-623-1
X-3952-660-1
3-076-322-01
FP-503 FLEXIBLE BOARD (TRV940/TRV940E)
FP-503 FLEXIBLE BOARD (TRV950/TRV950E)
CABINET ASSY, GRIP (TRV950/TRV950E)
CABINET ASSY, GRIP (TRV940/TRV940E)
BELT, GRIP (TRV950/TRV950E)
253
254
3-076-322-11 BELT, GRIP (TRV940/TRV940E)
3-679-362-11 SCREW (M2X4)
Ref. No.
5-6
Part No.
Description
255
256
257
258
259
4-974-725-01
3-713-791-01
X-3952-598-1
1-785-593-31
X-3952-624-1
SCREW (M1.7X2.5), P
SCREW (M1.7X4), TAPPING, P2
CHASSIS ASSY, MS
CONNECTOR, MEMORY STICK
CABINET ASSY, MS
260
1-477-339-21 SWITCH BLOCK, CONTROL (CF1870)
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-7. STROBOSCOPE BLOCK
309
305
304
305
310
zD
(included in 308)
304
311
307
308
(including zD)
306
305
301
303
312
ANT901
302
304
304
TRV950/TRV950E
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Part No.
Description
Ref. No.
Part No.
Description
301
302
303
304
305
X-3952-601-1
3-076-313-01
3-076-340-01
3-989-735-81
3-713-791-01
BASE ASSY, ST
ST CABINET (FRONT)
COVER (LOWER), ST
SCREW (M1.7), LOCK ACE, P2
SCREW (M1.7X4), TAPPING, P2
0 308
309
310
311
312
1-477-398-11
3-076-342-01
X-3952-670-1
3-389-523-28
3-076-341-01
FLASH UNIT
COVER (UPPER), ST
CABINET (UPPER) ASSY, ST
SCREW (LOCK ACE)
COVER (FRONT), ST
306
307
X-3952-663-1 CABINET (LOWER) ASSY, ST
3-076-854-01 SHEET, INSULATING, ST
ANT901 1-754-210-21 ANTENNA (2.4Ghz) (TRV950/TRV950E)
5-7
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-8. EVF BLOCK
368
366
367
365
364
363
361
LCD903
362
357
360
355
356
354
359
353
358
351
359
357
352
Ref. No.
Part No.
Description
351
352
353
353
354
3-076-345-01
1-685-301-11
X-3952-625-1
X-3952-645-1
3-989-735-81
HOLDER, VF FLEXIBLE
FP-547 FLEXIBLE BOARD
CABINET ASSY, TOP (TRV950/TRV950E)
CABINET ASSY, TOP (TRV940/TRV940E)
SCREW (M1.7), LOCK ACE, P2
355
356
357
358
359
1-815-124-11
A-7078-344-A
4-974-725-01
X-3952-600-1
3-713-791-31
CONNECTOR, EXTERNAL (HOT SHOE)
FP-497 FLEXIBLE BOARD, COMPLETE
SCREW (M1.7X2.5), P
BASE ASSY, EVF
SCREW (M1.7X6), TAPPING, P2
Ref. No.
5-8
Part No.
Description
360
361
362
363
364
X-3952-614-1
A-7078-333-A
3-072-214-01
3-072-211-01
3-072-210-01
CABINET (LOWER) ASSY, VF
LB-080 BOARD, COMPLETE
GUIDE (20), LAMP
ILLUMINATOR
SHEET, PRISM
365
366
367
368
LCD903
3-059-734-01
X-3952-613-1
X-3952-616-1
3-074-434-01
8-753-028-54
CUSHION (1), LCD
CABINET (UPPER) ASSY, VF
LENS ASSY, VF
COVER VF LABEL (PR)
LCX033AN-1 (SERVICE)
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-9. BATTERY PANEL BLOCK
ns: not supplied
402
406
ns
407
408
ns
404
ns
ns
407
403
BT901
405
401
Ref. No.
401
402
403
404
405
Part No.
Description
3-076-245-01
X-3952-603-1
3-713-791-51
3-076-335-01
3-076-337-01
BRACKET (LOWER), STRAP
PANEL ASSY, BATTERY
SCREW (M1.7X3.5), TAPPING, P2
BRACKET (UPPER), STRAP
FOOT, RUBBER
Ref. No.
406
407
408
BT901
5-9
Part No.
Description
3-076-239-01
3-989-735-81
3-065-290-11
1-694-772-11
LID, CPC
SCREW (M1.7), LOCK ACE, P2
LID, JACK
TERMINAL BOARD, BATTERY
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-10. MD BLOCK
ns: not supplied
466
467
Overall mechanism deck section (J200)
(See page 5-12.)
452
456
453
451
468
454
457
462
456
465 464
8
28
C-
458
V
455
456
4
456
Lens block
(See page 5-11.)
-01
DB
459
463
461
456
456
460
Ref. No.
Part No.
Description
451
452
453
454
455
3-059-722-01
X-3952-662-1
X-3952-599-1
3-059-718-01
3-076-338-01
COVER, CASSETTE COMPARTMENT
BRACKET ASSY, HEAT SINK
FRAME ASSY, MD
SCREW (M1.4X1.5)
BRACKET, DB
456
457
457
457
4-974-725-01 SCREW (M1.7X2.5), P
A-7078-347-A VC-288 BOARD, COMPLETE (SERVICE) (TRV950)
A-7078-362-A VC-288 BOARD, COMPLETE (SERVICE)
(TRV950E)
A-7078-364-A VC-288 BOARD, COMPLETE (SERVICE)
(TRV940E)
A-7078-366-A VC-288 BOARD, COMPLETE (SERVICE) (TRV940)
458
A-7078-345-A FP-498 FLEXIBLE BOARD, COMPLETE
457
Ref. No.
5-10
Part No.
Description
459
460
461
462
463
A-7078-346-A
A-7078-343-A
1-685-292-11
1-685-291-11
A-7078-348-A
FP-499 FLEXIBLE BOARD, COMPLETE
FP-496 FLEXIBLE BOARD, COMPLETE
FP-494 FLEXIBLE BOARD
FP-493 FLEXIBLE BOARD
DB-014 BOARD, COMPLETE (SERVICE)
(TRV940/TRV950)
463
464
465
466
467
A-7078-363-A DB-014 BOARD, COMPLETE (SERVICE)
(TRV940E/TRV950E)
3-070-940-01 TAPE (3), DF
3-948-339-01 SCREW, TAPPING
3-989-735-01 SCREW (M1.7), LOCK ACE, P2
3-059-725-01 LABEL, LS
468
3-059-809-01 DAMPER, MD
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-11. LENS BLOCK
ns: not supplied
502
CD-389
503
503
504
501
ns
ns
ns
502
505
(Note 2)
ns
(Note 3)
503
M801
(Note 3)
ns
(Note 2) Be sure to read “Precuations for Replacement of CCD
Imager” on page 4-12 when changing the prism block.
(Note 3) Flexible board of video lens is not supplied.
Please be careful not to break the flexible board when
you change the motor unit.
Ref. No.
501
502
503
504
Part No.
Description
1-758-757-11
3-713-791-61
3-076-331-01
A-7078-335-A
LENS, VIDEO (B144A)
SCREW (M1.7X7), TAPPING, P2
COVER (A), CCD
CD-389 BOARD, COMPLETE
Ref. No.
505
M801
5-11
Part No.
Description
A-7012-866-A PRISM BLOCK (ZGDSY2) (SERVICE)
(including CCD IMAGER (IC100, 101, 105))
(Note 2)
3-709-679-01 MOTOR, ZOOM (Note 3)
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-12. OVERALL MECHANISM DECK SECTION (J200)
M901
703
702
704
712
713
709
701
712
705
714
701
706
711
LS chassis block assembly
(See page 5-13.)
Mechanism chassis
block assembly
(See page 5-14.)
710
707
701
Ref. No.
701
702
703
Part No.
Descriptions
Ref. No.
704
705
3-703-816-14 SCREW (M1.4)
X-3952-017-3 CASSETTE COMPARTMENT ASSY
3-059-082-01 SPRING, TENSION
(CASSETE COMPARTMENT S)
3-059-208-01 SPRING (CASSETTE COMPARTMENT T)
X-3950-370-3 DAMPER ASSY
706
707
3-059-101-03 RETAINER, LS GUIDE
7-624-102-04 STOP RING 1.5, TYPE -E
5-12
Part No.
Description
709
710
711
712
713
3-704-197-21
X-3950-364-1
X-3950-366-1
3-075-097-01
3-059-093-01
SCREW (M1.4X2.5), SPECIAL HEAD
GEAR ASSY, GOOSENECK
TABLE ASSY, T REEL
SCREW (M1.4X1.4), SPECIAL HEAD
RETAINER, LED
714
M901
X-3950-361-1 PLATE ASSY, RETAINER
A-7048-968-A DRUM (DEH-18E-R) (SERVICE)
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-13. LS CHASSIS BLOCK ASSEMBLY
ns: not supplied
762
763
761
760
758
759
ns
757
764
ns
ns
Q901
756
D901
H901
H902
S903
Q902
768
FP-102
(Note)
755
766
765
769
754
767
770
ns
753
752
751
Note: FP-102 is included in the LS sub assy and is attached
to chassis by hot-press.
Because installation of FP-102 requires a very high
accuracy, FP-102 is not supplied as an independent
service parts.
Ref. No.
Part No.
Description
751
752
753
754
755
3-059-173-01
3-075-097-01
A-7094-816-B
X-3950-371-1
3-059-166-01
PLATE, LS CAM
SCREW (M1.4X1.4), SPECIAL HEAD
LS BLOCK ASSY
ARM ASSY, BRAKE (S) DRIVING
BRAKE (S)
756
757
758
759
760
3-059-146-01
3-059-167-01
3-059-169-01
3-703-816-14
3-059-090-01
POSITIONING (S), CASSETTE
SPRING (BRAKE S), TENSION COIL
SPRING (BRAKE S ARM), TORSION
SCREW (M1.4)
SCREW (M1.4X2.5), SPECIAL HEAD
* 761
762
763
Ref. No.
X-3950-358-4 TG1 ASSY
3-059-156-01 SPRING (TENSION REGULATOR)
X-3950-365-2 TABLE ASSY, S REEL
5-13
Part No.
Description
764
765
766
767
768
A-7094-819-A
3-059-165-01
X-3950-359-1
3-059-161-01
3-059-170-01
TG7 BLOCK ASSY
SPRING (TG7 RETURN), TORSION
ARM ASSY, PINCH
SPRING (PINCH RETURN), TORSION
BRAKE (T)
769
770
D901
H901
H902
3-059-171-01
3-059-172-01
8-719-078-71
8-719-067-74
8-719-067-74
GEAR (T), BRAKE
SPRING (T), BRAKE
DIODE LN57A,SO (TAPE LED)
ELEMENT, HOLE HW-105A-CDE-T (S REEL)
ELEMENT, HOLE HW-105A-CDE-T (T REEL)
Q901
Q902
S903
8-729-028-71 TRANSISTOR, PN166,SO (TAPE END)
8-729-028-71 TRANSISTOR, PN166,SO (TAPE TOP)
1-572-288-11 SWITCH, PUSH (C.C. DOWN)
DCR-TRV940/TRV940E/TRV950/TRV950E
5-1-14. MECHANISM CHASSIS BLOCK ASSEMBLY
815
ns: not supplied
807
811
822
812
813
824
820
821
814
823
815
816
810
M903
ns
815
815
825
830
819
815
809
808
818
M902
(including belt)
806
807
815
829
804
817
(including S902)
826
827
805
801
828
803
802
ns
Ref. No.
Part No.
Description
801
802
803
804
805
3-059-211-01
3-059-220-01
3-059-187-01
3-059-186-02
3-060-002-01
GEAR, CONVERSION
GEAR, RELAY
SHAFT, WORM
HOLDER, MOTOR
ROLLER, LS GUIDE
Ref. No.
806
807
808
809
810
3-059-189-01
3-704-197-21
3-059-225-01
3-059-191-01
3-059-190-01
GEAR (A), CAM
SCREW (M1.4X2.5), SPECIAL HEAD
SHIELD, MOTOR
ROLLER, LS
ARM, LS
811
812
813
814
815
1-677-049-11
1-677-084-11
3-059-149-01
3-059-148-01
3-703-816-14
FP-228 FLEXIBLE BOARD (DEW SENSOR)
FP-100 FLEXIBLE BOARD
SLIDER, TG1 CAM
ARM, TG1 DRIVING
SCREW (M1.4)
816
817
3-059-117-01 COVER (A), GEAR
X-3950-367-1 GEAR ASSY, MODE
(including S902 (MODE SWITCH))
5-14
Part No.
Description
818
819
820
3-059-139-01 GEAR, GL DRIVING
3-059-188-01 GEAR, DECELERATION
A-7094-818-A COASTER (S) BLOCK ASSY
821
822
823
824
825
A-7094-817-A
3-059-126-01
3-962-914-01
A-7094-822-A
3-059-118-01
COASTER (T) BLOCK ASSY
RAIL, GUIDE
SCREW (M1.4X2)
DRUM BASE BLOCK ASSY
COVER (B), GEAR
826
827
828
829
830
3-059-083-01
X-3950-368-1
3-059-192-01
3-063-355-01
3-065-202-01
COVER (C), GEAR
ARM ASSY, PINCH DRIVING
GEAR (B), CAM
ROLLER (S1), LS GUIDE
SUPPORT, TG7
M902
8-835-685-01 MOTOR, DC SCD18A/C-NP
(including BELT) (CAPSTAN)
A-7094-823-A MOTOR BLOCK ASSY, L
M903
DCR-TRV940/TRV940E/TRV950/TRV950E
BT-003
CD-389
5-2. ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
Ref. No.
Part No.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. .
: µPA. .
uPB. . : µPB. .
uPC. .
: µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
EE : East European model
HK : Hong Kong model
JE : Tourist model
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
KR : Korean model
NE : North European model
RU : Russian model
Description
Ref. No.
A-7067-302-A BT-003 BOARD, COMPLETE (TRV950/TRV950E)
**********************
(Parts on BT-003 board are not replaced individually. They are supplied as
being mounted.)
Part No.
Description
< CONNECTOR >
CN100
1-784-938-21 CONNECTOR, BOARD TO BOARD 60P
< IC >
A-7078-335-A CD-389 BOARD, COMPLETE
***********************
(IC100, 101 and 105 are not included in this complete board.)
< CAPACITOR >
C102
C103
C104
C105
C106
1-115-339-11
1-115-339-11
1-127-895-91
1-164-943-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
22uF
0.01uF
0.1uF
10%
10%
20%
10%
10%
50V
50V
4V
16V
10V
C107
C108
C109
C110
C111
1-125-777-11
1-125-777-11
1-162-970-11
1-162-970-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
25V
25V
16V
C112
C113
C114
C115
C116
1-107-826-11
1-104-851-11
1-104-851-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
10uF
0.1uF
0.1uF
10%
20%
20%
10%
10%
16V
10V
10V
10V
10V
C117
C118
C119
C120
C121
1-125-777-11
1-125-777-11
1-125-777-11
1-125-777-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
16V
C122
C123
C124
C125
C126
1-162-970-11
1-125-777-11
1-125-777-11
1-125-777-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.1uF
0.01uF
10%
10%
10%
10%
10%
25V
10V
10V
10V
16V
C127
C128
C129
C130
C131
1-164-943-11
1-127-895-91
1-127-895-91
1-115-339-11
1-104-851-11
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
TANTAL. CHIP
0.01uF
22uF
22uF
0.1uF
10uF
10%
20%
20%
10%
20%
16V
4V
4V
50V
10V
(Note 1) Be sure to read “Note on the CCD Imager Replacement” on page 4-12 when changing the
prism block.
IC100
IC101
IC102
IC103
IC104
A-7012-866-A
A-7012-866-A
6-701-755-01
6-701-755-01
6-701-755-01
PRISM BLOCK (ZGDSY2) (Note 1, 2)
PRISM BLOCK (ZGDSY2) (Note 1, 2)
IC AD80017AJRURL
IC AD80017AJRURL
IC AD80017AJRURL
IC105
A-7012-866-A PRISM BLOCK (ZGDSY2) (Note 1, 2)
< COIL >
L100
L101
L102
L103
L104
1-469-058-11
1-469-525-91
1-469-525-91
1-469-058-11
1-469-058-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
22uH
10uH
10uH
22uH
22uH
L105
1-469-525-91 INDUCTOR
10uH
< TRANSISTOR >
Q100
Q101
Q102
8-729-037-74 TRANSISTOR
8-729-037-74 TRANSISTOR
8-729-037-74 TRANSISTOR
UN9213J- (TX).SO
UN9213J- (TX).SO
UN9213J- (TX).SO
< RESISTOR >
5-15
R100
R101
R102
R103
R104
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R105
R106
R107
R108
R109
1-218-990-11
1-218-941-81
1-218-941-81
1-218-941-81
1-218-990-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
0
100
100
100
0
R110
R111
1-218-990-11 SHORT CHIP
1-218-990-11 SHORT CHIP
5%
5%
5%
1/16W
1/16W
1/16W
0
0
(Note 2) CCD Imager (IC100, 101 and 105) is supplied
as a prism block.
DCR-TRV940/TRV940E/TRV950/TRV950E
CK-116
Ref. No.
Part No.
Description
Ref. No.
A-7078-338-A CK-116 BOARD, COMPLETE
***********************
Part No.
Description
R5235
R5236
R5237
1-218-970-11 RES-CHIP
1-218-970-11 RES-CHIP
1-218-970-11 RES-CHIP
27K
27K
27K
5%
5%
5%
1/16W
1/16W
1/16W
R5238
R5239
R5240
R5243
R5244
1-218-970-11
1-218-990-11
1-218-990-11
1-218-949-11
1-218-990-11
27K
0
0
470
0
5%
1/16W
5%
1/16W
< BATTERY >
BT5201 1-756-128-11 BATTERY, LITHIUM (SECONDARY)
< CAPACITOR >
C5201
C5202
CN5201
CN5202
CN5203
CN5204
CN5205
1-135-957-91 TANTAL. CHIP
1-125-777-11 CERAMIC CHIP
1-794-997-11
1-816-463-11
1-784-938-21
1-794-375-21
1-816-684-11
10uF
0.1uF
20%
10%
16V
10V
RES-CHIP
SHORT CHIP
SHORT CHIP
RES-CHIP
SHORT CHIP
< SWITCH >
< CONNECTOR >
S5116
1-771-138-82 SWITCH, KEY BOARD
PIN, CONNECTOR 20P
PIN, CONNECTOR (PC BOARD) 10P
CONNECTOR, BOARD TO BOARD 60P
PIN, CONNECTOR 2P
CONNECTOR, FFC/FPC (ZIF) 8P
S5201
S5202
S5203
S5204
1-572-342-11
1-762-648-21
1-771-138-82
1-571-787-31
(DISPLAY/TOUCH PANEL)
SWITCH, SLIDE (AUTO LOCK/MANU/HOLD)
SWITCH, SLIDE (ZEBRA OFF/70/100)
SWITCH, KEY BOARD (DATA CODE)
SWITCH, TACTILE (EDITSEARCH-)
S5205
S5206
S5207
S5208
S5209
1-571-787-31
1-771-138-82
1-771-138-82
1-771-138-82
1-771-138-82
SWITCH, TACTILE (EDITSEARCH+)
SWITCH, KEY BOARD (STOP)
SWITCH, KEY BOARD (REW)
SWITCH, KEY BOARD (PLAY)
SWITCH, KEY BOARD (FF)
S5210
S5211
S5212
S5213
S5214
1-771-138-82
1-771-138-82
1-771-138-82
1-771-138-82
1-771-138-82
SWITCH, KEY BOARD (PAUSE)
SWITCH, KEY BOARD (REC)
SWITCH, KEY BOARD (REC)
SWITCH, KEY BOARD (COLOR BAR)
SWITCH, KEY BOARD (VOLUME+)
S5215
S5217
S5218
S5219
S5220
1-771-138-82
1-771-138-82
1-571-787-31
1-571-787-31
1-771-138-82
SWITCH, KEY BOARD (VOLUME-)
SWITCH, KEY BOARD (AUDIO DUB)
SWITCH, TACTILE (BACK LIGHT)
SWITCH, TACTILE (SPOT LIGHT)
SWITCH, KEY BOARD (CUSTOM PRESET)
S5221
1-771-138-82 SWITCH, KEY BOARD (RESET)
CN5206 1-766-336-21 CONNECTOR, FFC/FPC 6P
< DIODE >
D5201
D5202
D5203
D5204
D5205
8-719-056-61
8-719-062-16
8-719-062-16
8-719-056-61
8-719-062-16
DIODE
DIODE
DIODE
DIODE
DIODE
MAZS082008SO
01ZA8.2 (TPL3)
01ZA8.2 (TPL3)
MAZS082008SO
01ZA8.2 (TPL3)
D5206
D5207
D5208
D5209
8-719-062-16
8-719-062-16
8-719-062-16
8-719-062-16
DIODE
DIODE
DIODE
DIODE
01ZA8.2 (TPL3)
01ZA8.2 (TPL3)
01ZA8.2 (TPL3)
01ZA8.2 (TPL3)
< RESISTOR >
R5208
R5209
R5210
R5211
R5212
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R5213
R5214
R5215
R5216
R5217
1-218-954-11
1-218-954-11
1-218-954-11
1-218-954-11
1-218-955-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.2K
1.2K
1.2K
1.2K
1.5K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5218
R5219
R5220
R5221
R5222
1-218-955-11
1-218-955-11
1-218-955-11
1-218-957-11
1-218-957-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.5K
1.5K
1.5K
2.2K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5223
R5224
R5225
R5226
R5227
1-218-957-11
1-218-957-11
1-218-964-11
1-218-960-11
1-218-960-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
2.2K
8.2K
3.9K
3.9K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5228
R5229
R5230
R5231
R5232
1-218-960-11
1-218-960-11
1-218-970-11
1-218-964-11
1-218-964-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
3.9K
3.9K
27K
8.2K
8.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5233
R5234
1-218-964-11 RES-CHIP
1-218-964-11 RES-CHIP
8.2K
8.2K
5%
5%
1/16W
1/16W
Electrical parts list of the DB-014 board is
not shown.
Page 5-17 to 5-23 are not shown.
5-16
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or eqivalent type.
DCR-TRV940/TRV940E/TRV950/TRV950E
FP-102
Ref. No.
Part No.
FP-495
FP-496
FP-497
Description
FP-498
Ref. No.
FP-102 FLEXIBLE BOARD (Not supplied)
*********************
FP-499
Part No.
JK-222
Description
A-7078-341-A FP-504 FLEXIBLE BOARD, COMPLETE
*******************************
< HOLE ELEMENT >
H901
H902
FP-504
< CAPACITOR >
8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (S REEL)
8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (T REEL)
C601
1-137-710-11 CERAMIC CHIP
10uF
20%
6.3V
< DIODE >
< DIODE >
D901
D601
D602
D603
8-719-078-71 DIODE LN57A.SO (TAPE LED)
D605
D606
8-719-070-92 DIODE TLOU1008 (T05, SOY) (FLASH)
8-719-052-25 DIODE CL-200IR-X-TU-BC (IR)
8-719-061-82 DIODE TLSU1002 (TPX1, SONY)
(CAMERA RECORDING)
8-719-062-16 DIODE 01ZA8.2 (TPL3)
8-719-056-23 DIODE MA2S111- (K8).SO
D607
D608
D609
D610
8-719-062-16
8-719-062-16
8-719-062-16
8-719-062-16
< TRANSISTOR >
Q901
Q902
8-729-028-71 TRANSISTOR
8-729-028-71 TRANSISTOR
PN166.SO (TAPE END)
PN166.SO (TAPE TOP)
< SWITCH >
S903
1-572-288-11 SWITCH, PUSH (C, C, DOWN)
DIODE
DIODE
DIODE
DIODE
01ZA8.2 (TPL3)
01ZA8.2 (TPL3)
01ZA8.2 (TPL3)
01ZA8.2 (TPL3)
< FUSE >
A-7078-342-A FP-495 FLEXIBLE BOARD, COMPLETE
*******************************
S001
S002
0 F601
1-533-874-11 FUSE, MICRO (0.2A/24V)
< IC >
1-786-179-31 SWITCH, PUSH (1KEY) (PANEL OPEN)
1-771-039-31 SWITCH, PUSH (PANEL REVERSE)
IC601
8-742-221-00 HYB IC SBX3055-01
A-7078-343-A FP-496 FLEXIBLE BOARD, COMPLETE
*******************************
< PHOTO INTERRUPTER >
PH601
PH602
< CONNECTOR >
CN001
CN002
8-759-014-54 HIC CNA1312K01S0
8-759-014-54 HIC CNA1312K01S0
1-784-938-21 CONNECTOR, BOARD TO BOARD 60P
1-784-939-11 CONNECTOR, BOARD TO BOARD 60P
< TRANSISTOR >
Q601
8-729-037-72 TRANSISTOR
A-7078-344-A FP-497 FLEXIBLE BOARD, COMPLETE
*******************************
< RESISTOR >
< DIODE >
D001
UN9211J- (K8).SO
8-719-080-62 DIODE CL-190HBF-X-T (BLUETOOTH) (Note)
R601
R602
R603
R604
R605
1-216-838-11
1-216-832-11
1-216-813-11
1-216-828-11
1-216-805-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
R606
R607
1-216-815-11 METAL CHIP
1-216-821-11 METAL CHIP
27K
8.2K
220
3.9K
47
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
330
1K
5%
5%
1/16W
1/16W
< SWITCH >
S001
1-771-138-82 SWITCH, KEY BOARD (NETWORK) (Note)
< SWITCH >
A-7078-345-A FP-498 FLEXIBLE BOARD, COMPLETE
*******************************
S601
S602
S603
S604
< CONNECTOR >
CN001
CN002
1-771-487-21
1-771-138-82
1-771-138-82
1-771-138-82
SWITCH, SLIDE (FOCUS AUTO/MAN/INFINITY)
SWITCH, KEY BOARD (PUSH AUTO)
SWITCH, KEY BOARD (STROBO)
SWITCH, KEY BOARD (FADER)
1-785-969-21 CONNECTOR, BOARD TO BOARD 100P
1-785-967-21 CONNECTOR, BOARD TO BOARD 100P
A-7078-332-A JK-222 BOARD, COMPLETE
**********************
A-7078-346-A FP-499 FLEXIBLE BOARD, COMPLETE
*******************************
CN001
CN002
< CONNECTOR >
1-815-854-11 CONNECTOR, BOARD TO BOARD 80P
1-815-855-31 CONNECTOR, BOARD TO BOARD 80P
CN401
CN402
1-785-828-11 CONNECTOR, SQUARE TYPE 4P (DV IN/OUT)
1-794-962-11 CONNECTOR, SQUARE TYPE (USB 5P) (USB)
< DIODE >
D401
D402
(Note) Although parts are mounted on the board,
they are not used in TRV940/TRV940E.
5-24
8-719-062-16 DIODE 01ZA8.2 (TPL3)
8-719-062-16 DIODE 01ZA8.2 (TPL3)
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DCR-TRV940/TRV940E/TRV950/TRV950E
JK-222
Ref. No.
Part No.
Description
Ref. No.
Part No.
< FERRITE BEAD >
FB401
FB402
FB403
FB404
FB405
1-500-444-11
1-500-444-11
1-500-444-11
1-500-444-11
1-500-444-11
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
FB406
FB407
1-500-444-11 FERRITE
1-500-444-11 FERRITE
0uH
0uH
1-778-518-11
1-793-995-11
1-569-950-41
1-778-040-11
MA-410
Description
< IC >
IC6101
8-759-581-11 IC NJM2125F (TE2)
< TRANSISTOR >
Q6101
Q6102
8-729-054-48 TRANSISTOR
8-729-054-48 TRANSISTOR
RN4983FE (TPLR3)
N1B04FE-Y/GR (TPLR3)
< RESISTOR >
< JACK >
J401
J402
J403
J404
LB-080
CONNECTOR, EXTERNAL (S VIDEO ID-2)
JACK, SUPER SMALL TYPE (LANC)
JACK (SMALL TYPE) (HEADPHONES)
JACK, SMALL TYPE (AUDIO/VIDEO)
R6101
R6102
R6103
R6104
R6105
1-218-948-11
1-208-941-11
1-208-719-11
1-218-959-11
1-216-839-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
R6106
1-211-977-11 METAL CHIP
390
180K
33K
3.3K
33K
5%
0.5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
22
0.5%
1/10W
< LINE FILTER >
< THERMISTOR >
LF401
LF402
1-419-100-21 INDUCTOR
1-419-100-21 INDUCTOR
0uH
0uH
TH6101 1-810-811-11 THERMISTOR, NTC (1608)
< RESISTOR >
R401
R402
R403
R404
R406
1-216-864-11
1-216-864-11
1-216-864-11
1-218-965-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
0
0
0
10K
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R407
R408
R409
R410
R411
1-218-965-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
0
0
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
A-7078-336-A MA-410 BOARD, COMPLETE
***********************
< CAPACITOR >
< VARISTOR >
VDR401
VDR402
VDR403
VDR404
VDR405
1-801-862-11
1-803-742-21
1-803-742-21
1-801-862-11
1-803-742-21
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
VDR406
VDR407
VDR408
VDR409
1-801-862-11
1-801-862-11
1-801-862-11
1-803-742-21
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
A-7078-333-A LB-080 BOARD, COMPLETE
***********************
< CAPACITOR >
C6101
C6102
1-125-777-11 CERAMIC CHIP
1-164-505-11 CERAMIC CHIP
0.1uF
2.2uF
10%
10V
16V
< CONNECTOR >
CN6101 1-573-360-21 CONNECTOR, FFC/FPC 20P
CN6102 1-573-356-21 CONNECTOR, FFC/FPC 16P
C5901
C5905
C5906
C5907
C5908
1-164-939-11
1-107-819-11
1-107-819-11
1-107-819-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.022uF
0.022uF
0.022uF
0.01uF
10%
10%
10%
10%
10%
50V
16V
16V
16V
16V
C5909
C5910
C5911
C5912
C5913
1-107-819-11
1-117-919-11
1-164-937-11
1-117-919-11
1-164-874-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
0.022uF
10uF
0.001uF
10uF
100PF
10%
20%
10%
20%
5%
16V
6.3V
50V
6.3V
50V
C5914
C5915
C5917
C5918
C5920
1-164-874-11
1-164-937-11
1-164-874-11
1-164-874-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.001uF
100PF
100PF
0.1uF
5%
10%
5%
5%
10%
50V
50V
50V
50V
10V
C5921
C5922
C5923
C5924
C5925
1-125-777-11
1-125-777-11
1-165-176-11
1-125-777-11
1-165-176-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.047uF
0.1uF
0.047uF
10%
10%
10%
10%
10%
10V
10V
16V
10V
16V
C5926
C5927
C5928
C5929
C5930
1-164-174-11
1-164-174-11
1-164-245-11
1-164-942-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0082uF
0.0082uF
0.015uF
0.0068uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
16V
16V
C5931
C5932
C5933
C5934
C5935
1-164-245-11
1-117-919-11
1-125-777-11
1-164-156-11
1-117-919-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
0.015uF
10uF
0.1uF
0.1uF
10uF
10%
20%
10%
20%
25V
6.3V
10V
25V
6.3V
C5936
C5937
C5938
1-165-128-11 CERAMIC CHIP
1-125-841-91 TANTAL. CHIP
1-125-777-11 CERAMIC CHIP
20%
10%
16V
4V
10V
< DIODE >
D6101
D6102
8-719-018-51 DIODE CL-170R-CD-T (REC)
8-719-082-33 DIODE NSCW100-T39 (BACKLIGHT)
5-25
0.22uF
22uF
0.1uF
DCR-TRV940/TRV940E/TRV950/TRV950E
MA-410
Ref. No.
PD-168
Part No.
Description
Ref. No.
C5939
C5940
1-125-777-11 CERAMIC CHIP
1-125-777-11 CERAMIC CHIP
0.1uF
0.1uF
10%
10%
10V
10V
C5941
C5944
1-125-777-11 CERAMIC CHIP
1-164-937-11 CERAMIC CHIP
0.1uF
0.001uF
10%
10%
C5945
1-164-937-11 CERAMIC CHIP
0.001uF
10%
10V
50V
(Note)
50V
(Note)
< CONNECTOR >
* CN5901 1-580-055-21
* CN5902 1-580-055-21
CN5903 1-779-327-11
CN5904 1-816-684-11
CN5905 1-816-177-11
PIN, CONNECTOR (SMD) 2P
PIN, CONNECTOR (SMD) 2P
CONNECTOR, FFC/FPC 6P
CONNECTOR, FFC/FPC (ZIF) 8P
CONNECTOR, FFC/FPC (ZIF) 16P
CN5906 1-784-422-11 CONNECTOR, FFC/FPC (ZIF) 33P
Part No.
Description
R5916
1-218-957-11 RES-CHIP
2.2K
5%
1/16W
R5917
R5918
R5919
R5920
R5921
1-218-957-11
1-218-967-11
1-208-910-11
1-218-967-11
1-208-910-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
15K
9.1K
15K
9.1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5922
R5923
R5924
R5925
R5926
1-218-949-11
1-218-990-11
1-218-990-11
1-218-949-11
1-216-829-11
RES-CHIP
SHORT CHIP
SHORT CHIP
RES-CHIP
METAL CHIP
470
0
0
470
4.7K
5%
1/16W
5%
5%
1/16W
1/16W
R5927
R5928
R5929
R5930
R5931
1-220-191-81
1-220-191-81
1-216-817-11
1-216-823-11
1-218-971-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
5.1K
5.1K
470
1.5K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5933
R5934
R5935
R5936
R5937
1-218-954-11
1-218-968-11
1-218-971-11
1-216-825-11
1-216-837-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
1.2K
18K
33K
2.2K
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5938
R5939
R5940
R5941
R5943
1-208-912-11
1-216-820-11
1-216-833-11
1-208-701-11
1-208-912-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
11K
820
10K
5.6K
11K
0.5%
5%
5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5944
R5946
R5947
R5948
R5949
1-218-943-11
1-216-864-11
1-218-952-11
1-218-941-81
1-218-973-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
150
0
820
100
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5951
R5952
R5953
1-218-949-11 RES-CHIP
1-218-947-11 RES-CHIP
1-216-313-00 METAL CHIP
470
330
8.2
5%
5%
5%
1/16W
1/16W
1/10W
< DIODE >
D5903
8-719-062-16 DIODE 01ZA8.2 (TPL3)
< FERRITE BEAD >
FB5901 1-500-444-11 FERRITE
FB5902 1-500-444-11 FERRITE
0uH
0uH
< IC >
IC5901
IC5902
8-759-638-50 IC AN2901FHQ-EB
8-759-581-11 IC NJM2125F (TE2)
< JACK >
J5901
1-691-737-41 JACK (SMALL TYPE) (MIC (PLUG IN POWER))
< COIL >
L5901
1-469-528-91 INDUCTOR
100uH
< TRANSISTOR >
< VARISTOR >
Q5901
Q5902
Q5903
Q5904
Q5905
8-729-042-26
8-729-048-77
8-729-048-77
8-729-402-42
8-729-403-35
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q5906
8-729-140-75 TRANSISTOR
2SB1462J-QR (K8).SO
XP4313- (TX).SO
XP4313- (TX).SO
UN5213-TX
UN5113-TX
VDR591 1-801-862-11 VARISTOR, CHIP
VDR592 1-801-862-11 VARISTOR, CHIP
A-7078-337-A PD-168 BOARD, COMPLETE
***********************
2SD999-T1-CLCK
< RESISTOR >
< CAPACITOR >
R5901
R5902
R5903
R5904
R5905
1-216-864-11
1-218-990-11
1-218-968-11
1-218-971-11
1-218-961-11
METAL CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
0
18K
33K
4.7K
5%
1/16W
1/16W
1/16W
1/16W
C5701
C5702
C5703
C5704
C5705
1-113-988-11
1-125-777-11
1-107-826-11
1-164-943-11
1-164-943-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
68uF
0.1uF
0.1uF
0.01uF
0.01uF
20%
10%
10%
10%
10%
4V
10V
16V
16V
16V
5%
5%
5%
R5906
R5907
R5908
R5909
R5910
1-218-965-11
1-218-957-11
1-218-957-11
1-218-963-11
1-218-963-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
2.2K
2.2K
6.8K
6.8K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
C5706
C5707
C5708
C5709
C5710
1-164-943-11
1-135-259-11
1-125-777-11
1-125-777-11
1-164-943-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
0.1uF
0.1uF
0.01uF
10%
20%
10%
10%
10%
16V
6.3V
10V
10V
16V
R5911
R5912
R5914
R5915
1-218-953-11
1-218-953-11
1-216-803-11
1-216-803-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
1K
1K
33
33
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
C5711
C5712
C5713
C5714
1-107-687-11
1-107-826-11
1-164-739-11
1-125-777-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
3.3uF
0.1uF
560PF
0.1uF
20%
10%
5%
10%
20V
16V
50V
10V
(Note) C5944 and C5945 are mounted on the board with
suffix number 12.
5-26
DCR-TRV940/TRV940E/TRV950/TRV950E
PD-168
Ref. No.
Part No.
Description
Ref. No.
C5715
1-125-777-11 CERAMIC CHIP
0.1uF
10%
10V
C5716
C5717
C5718
C5719
C5720
1-104-851-11
1-164-357-11
1-164-866-11
1-109-982-11
1-109-982-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.001uF
47PF
1uF
1uF
20%
5%
5%
10%
10%
10V
50V
50V
10V
10V
C5721
C5722
C5723
C5724
C5726
1-109-982-11
1-113-994-11
1-125-777-11
1-125-777-11
1-107-682-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
6.8uF
0.1uF
0.1uF
1uF
10%
20%
10%
10%
10%
10V
16V
10V
10V
16V
C5727
C5801
C5802
C5803
C5805
1-107-682-11
1-125-777-11
1-127-985-91
1-107-826-11
1-137-710-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
47uF
0.1uF
10uF
10%
10%
20%
10%
20%
16V
10V
16V
16V
6.3V
C5807
C5808
1-125-837-91 CERAMIC CHIP
1-165-897-11 TANTAL. CHIP
1uF
22uF
10%
20%
6.3V
10V
< CONNECTOR >
CN5701
CN5802
* CN5803
CN5804
CN5805
1-573-364-11
1-794-997-11
1-778-155-11
1-784-420-11
1-785-554-21
CONNECTOR, FFC/FPC 24P
PIN, CONNECTOR 20P
CONNECTOR, FFC/FPC (ZIF) 7P
CONNECTOR, FFC/FPC (ZIF) 21P
CONNECTOR (5P), CARD EDGE
Part No.
Description
R5707
R5708
R5709
R5710
R5711
1-216-835-11
1-218-958-11
1-218-973-11
1-218-975-11
1-218-969-11
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
15K
2.7K
47K
68K
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5712
R5713
R5714
R5717
R5719
1-218-975-11
1-218-989-11
1-218-977-11
1-216-864-11
1-218-942-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
68K
1M
100K
0
120
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5721
R5722
R5727
R5732
R5736
1-218-965-11
1-218-965-11
1-218-974-11
1-218-941-81
1-218-941-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
56K
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5737
R5801
R5802
R5803
R5804
1-218-941-81
1-218-941-81
1-216-855-11
1-218-961-11
1-218-953-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
100
100
680K
4.7K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5805
1-216-864-11 METAL CHIP
0
5%
1/16W
A-7078-339-A SE-132 BOARD, COMPLETE
***********************
CN5806 1-816-463-11 PIN, CONNECTOR (PC BOARD) 10P
< CAPACITOR >
< DIODE >
D5701
D5702
SE-132
8-719-404-50 DIODE MA111-TX
8-719-084-46 DIODE 1SV288 (TPH3)
C4001
C4002
C4003
C4004
C4005
1-127-895-91
1-127-895-91
1-125-777-11
1-125-777-11
1-119-923-81
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
22uF
0.1uF
0.1uF
0.047uF
20%
20%
10%
10%
10%
4V
4V
10V
10V
10V
C4006
C4007
C4008
C4009
C4010
1-119-923-81
1-119-923-81
1-119-923-81
1-127-692-11
1-127-692-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.047uF
0.047uF
10uF
10uF
10%
10%
10%
10%
10%
10V
10V
10V
6.3V
6.3V
C4011
C4012
C4014
C4015
1-127-692-11
1-127-692-11
1-127-895-91
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
10uF
10uF
22uF
0.1uF
10%
10%
20%
10%
6.3V
6.3V
4V
10V
< IC >
IC5701
IC5702
IC5801
6-702-491-01 IC AN12580A-BB
8-759-833-18 IC CM7021L3-E2
8-759-573-02 IC BU9735K-E2
< COIL >
L5701
L5702
L5703
L5704
L5705
1-469-525-91
1-414-771-91
1-414-771-91
1-414-771-91
1-412-943-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
2.2uH
L5801
L5802
1-412-056-11 INDUCTOR
1-414-757-11 INDUCTOR
4.7uH
100uH
< CONNECTOR >
CN4005 1-764-680-21 CONNECTOR, FFC/FPC (ZIF) 8P
< IC >
< TRANSISTOR >
IC4001
Q5701
Q5702
Q5801
Q5802
8-729-037-52
8-729-037-74
8-729-042-72
8-729-042-26
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD2216J-QR (K8).SO
UN9213J- (K8).SO
UN9214J- (K8).SO
2SB1462J-QR (K8).SO
< COIL >
L4001
< RESISTOR >
R5701
R5702
R5703
R5705
R5706
1-218-985-11
1-208-719-11
1-218-970-11
1-218-985-11
1-218-977-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
8-759-489-19 IC NJM3230V (TE2)
1-414-771-91 INDUCTOR
10uH
< TRANSISTOR >
470K
33K
27K
470K
100K
5%
0.5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
Q4001
Q4002
5-27
8-729-042-26 TRANSISTOR
8-729-037-74 TRANSISTOR
2SB1462J-QR (K8).SO
UN9213J- (K8).SO
DCR-TRV940/TRV940E/TRV950/TRV950E
SE-132
Ref. No.
Part No.
Description
Ref. No.
< RESISTOR >
R4001
R4002
R4003
R4004
R4005
1-218-969-11
1-218-969-11
1-218-969-11
1-218-969-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
22K
22K
22K
22K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4006
R4007
R4009
R4010
R4011
1-218-965-11
1-218-989-11
1-218-989-11
1-218-953-11
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
1M
1M
1K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< SENSOR >
SE4001 1-476-807-31 SENSOR, ANGULAR VELOCITY (PITCH)
SE4002 1-476-807-41 SENSOR, ANGULAR VELOCITY (YAW)
Electrical parts list of the VC-288 board is
not shown.
Page 5-29 to 5-36 are not shown.
5-28
Part No.
Description
DCR-TRV940/TRV940E/TRV950/TRV950E
Ref. No.
Part No.
Description
Ref. No.
ACCESSORIES
************
0
0
0
0
0
0
0
1-475-599-14
1-475-599-73
1-475-599-82
1-475-950-53
1-569-007-11
1-569-008-21 ADAPTOR, CONVERSION 2P (E, HK)
1-573-291-11 CONNECTOR, CONVERSION (21P)
(AEP, UK, EE, NE, RU)
1-575-131-11 CORD, POWER (AEP, EE, NE, RU)
1-696-819-11 CORD, POWER (AUS)
1-757-294-11 CORD, CONNECTION (USB 5P)
1-769-608-11
1-776-985-11
1-782-476-11
1-783-374-11
1-790-107-22
0
1-790-732-11 CORD, POWER (JE)
1-824-097-11 CORD, CONNECTION
Description
3-075-495-21 MANUAL, INSTRUCTION (FRENCH, GERMAN)
(TRV940E: E, JE/TRV950E: AEP, E)
3-075-495-31 MANUAL, INSTRUCTION (ENGLISH, DUTCH)
(TRV950E: AEP)
3-075-495-41 MANUAL, INSTRUCTION
(SPANISH, PORTUGUESE)
(TRV940E: AEP/TRV950E: AEP)
ADAPTOR, AC (EXCEPT KR, CH)
ADAPTOR, AC (KR)
ADAPTOR, AC (CH)
REMOTE COMMANDER (RMT-811)
ADAPTOR, CONVERSION (E, HK, JE)
0
0
0
0
0
Part No.
CORD, POWER (E)
CORD, POWER (KR)
CORD, POWER (CH)
CORD, POWER (UK, HK)
CORD, POWER (US, CND)
3-075-495-51 MANUAL, INSTRUCTION (ITALIAN, GREEK)
(TRV940E: AEP/TRV950E: AEP)
3-075-495-61 MANUAL, INSTRUCTION (ARABIC, PERSIAN)
(TRV940E: E/TRV950E: E)
3-075-495-71 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (TRV950E: HK)
3-075-495-81 MANUAL, INSTRUCTION
(SIMPLIFIED CHINESE)
(TRV940E: E, CH, JE/TRV950E: E)
3-987-015-01 BELT (S), SHOULDER
A-7024-735-A MEMORY BLOCK ASSY (8),PACKING
(A/V CONNECTING CABLE)
3-053-056-01 LID, BATTERY CASE (FOR RMT-811)
3-072-414-01 SPVD-008 (CD-ROM) (EXCEPT US, CND)
3-072-654-01 SPVD-008 (I) (CD-ROM) (US, CND)
3-073-861-01 CLOTH (TL), CLEANING
3-074-603-11 OPERATING INSTRUCTIONS FOR N/W
(ENGLISH) (TRV950: US)
3-075-396-11 MANUAL, NETWORK INSTRUCTION
(ENGLISH, FRENCH)
(TRV950: CND,E/TRV950E: E, HK, AUS)
3-075-396-21 MANUAL, NETWORK INSTRUCTION (ENGLISH)
(TRV950E: UK)
3-075-396-31 MANUAL, NETWORK INSTRUCTION
(ENGLISH, DUTCH) (TRV950E: AEP)
3-075-396-41 MANUAL, NETWORK INSTRUCTION
(FRENCH, GERMAN) (TRV950E: AEP)
3-075-396-51 MANUAL, NETWORK INSTRUCTION
(ITALIAN, GREEK) (TRV950E: AEP)
3-075-396-61 MANUAL, NETWORK INSTRUCTION
(SPANISH, PORTUGUESE) (TRV950E: AEP)
3-075-396-71 MANUAL, NETWORK INSTRUCTION
(TRADITIONAL CHINESE)
(TRV950: E/TRV950E: HK)
3-075-396-81 MANUAL, NETWORK INSTRUCTION
(SIMPLIFIED CHINESE) (TRV950E: E)
3-075-494-11 MANUAL, INSTRUCTION (ENGLISH)
(TRV940: E, HK, JE/TRV950)
3-075-494-21 MANUAL, INSTRUCTION (FRENCH)
(TRV950: CND)
3-075-494-31 MANUAL, INSTRUCTION
(SPANISH, PORTUGUESE)
(TRV940: E, JE/TRV950: E)
3-075-494-41 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE)
(TRV940: E, HK/TRV950: E)
3-075-494-51 MANUAL, INSTRUCTION (ARABIC)
(TRV940: E/TRV950: E)
3-075-494-61 MANUAL, INSTRUCTION (KOREAN)
(TRV940: KR, JE)
3-075-495-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH)
(TRV940E: E, CH, JE/TRV950E: UK, E, HK, AUS)
5-37E
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DCR-TRV940/TRV940E/TRV950/TRV950E
9-929-978-31
Sony EMCS Co.
— 146 —
2002I0500-1
©2002.09
Published by DI Customer Center
Reverse
992997832.pdf
Revision History
Ver.
Date
History
1.0
2002.05
Official Release
1.1
2002.09
Correction-1
(C1)
Contents
—
• Correction of BLOCK DIAGRAMS
• Correction of FRAME SCHEMATIC
DIAGRAMS
• Correction of SCHEMATIC DIAGRAMS
S.M. correction : Page 3-1, Page 4-1,
Page 4-77
S.M. Rev.
issued
—
Yes