No category

Download SERVICE MANUAL - EXIT EQUIPMENT

Transcript

HDR-TG1/TG1E/TG3E
SERVICE MANUAL
LEVEL
2
US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
Ver. 1.3 2009.06
Revision History
Revised-1
Replacement of the previously issued
SERVICE MANUAL 9-852-295-32
with this manual.
Photo: HDR-TG1
Link
SPECIFICATIONS
DISASSEMBLY
SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAM
REPAIR PARTS LIST
• Precaution on Replacing the VC-522 Board
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DIGITAL HD VIDEO CAMERA RECORDER
HDR-TG1/TG1E/TG3E_L2
9-852-295-33
Sony EMCS Co.
2009F0500-1
© 2009.6
Published by Kohda TEC
These specifications are extracted from instruction
manual of HDR-TG1E/TG3E.
ENGLISH
JAPANESE
SPECIFICATIONS
System
Input/Output connectors
AC Adaptor AC-L200/L200B
Video compression format: AVCHD (HD)/
MPEG2 (SD)/JPEG (Still images)
Audio compression format: Dolby Digital 2/5.1ch
Dolby Digital 5.1 Creator
Video signal: PAL color, CCIR standards
1080/50i specification
Recording format: Movie (HD): AVCHD 1080/
50i
Movie (SD): MPEG2-PS
Still image: Exif Ver.2.2*1
Image device: 3.6 mm (1/5 type) CMOS sensor
Recording pixels (still image, 4:3):
Max. 4.0 mega (2 304 × 1 728) pixels*2
Gross: Approx. 2 360 000 pixels
Effective (movie, 16:9): Approx. 1 430 000
pixels
Effective (still image, 16:9): Approx.
1 490 000 pixels
Effective (still image, 4:3): Approx. 1 990 000
pixels
Lens: Carl Zeiss Vario-Tessar
10 × (Optical), 20 ×, 120 × (Digital)
Focal length: F1.8 ~ 2.3
f=3.2 ~ 32.0 mm (5/32 ~ 1 5/16 in.)
When converted to a 35 mm still camera
For movies*3: 43 ~ 507 mm (1 3/4 ~ 20 in.)
(16:9)
For still images: 38 ~ 380 mm (1 1/2 ~ 15 in.)
(4:3)
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K),
[OUTDOOR] (5 800 K)
Minimum illumination: 5 lx (lux) ([AUTO SLW
SHUTTR] [ON], Shutter speed 1/25 sec)
A/V Remote Connector: Component/video and
audio output jack
HDMI OUT jack: HDMI mini Connector
Power requirements: AC 100 V - 240 V, 50/60 Hz
Current consumption: 0.35 - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to + 40 °C (32 °F to
104 °F)
Storage temperature: -20 °C to + 60 °C (-4 °F to +
140 °F)
Dimensions (approx.): 48 × 29 × 81 mm
(1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
excluding the projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
*1 “Exif” is a file format for still images,
established by the JEITA (Japan
Electronics and Information Technology
Industries Association). Files in this
format can have additional information
such as your camcorder’s setting
information at the time of recording.
*2 The unique pixel array of Sony’s ClearVid
CMOS sensor and image processing
system (BIONZ) allows still image
resolution equivalent to the sizes
described.
*3 The focal length figures are actual figures
resulting from wide angle pixel readout.
LCD screen
Image: 6.7 cm (2.7 type, aspect ratio 16:9)
Total dot number: 211 200 (960 × 220)
General
Power requirements: DC 6.8 V/7.2 V (battery
pack)
DC 8.4 V (AC Adaptor)
Average power consumption: During camera
recording using the LCD with normal
brightness:
HD: 3.3 W
SD: 2.7 W
Operating temperature: 0 °C to + 40 °C (32 °F to
104 °F)
Storage temperature: -20 °C to + 60 °C (-4 °F to +
140 °F)
Dimensions (approx.): 32 × 119 × 63 mm
(1 5/16 × 4 3/4 × 2 1/2 in.) (w/h/d)
including the projecting parts
32 × 119 × 63 mm
(1 5/16 × 4 3/4 × 2 1/2 in.) (w/h/d)
including the projecting parts, and the supplied
rechargeable battery pack attached
Mass (approx.): 240 g (8 oz) main unit only
300 g (10 oz) including the supplied
rechargeable battery pack, and a “Memory
Stick PRO Duo”
Handycam Station DCRA-C230
Input/Output connectors
A/V OUT jack: Component/video and audio
output jack
USB jack: mini-B
(HDR-TG3E: output only)
Dedicated USB Terminal Adaptor
Input/Output connectors
USB jack: mini-B
(HDR-TG3E: output only)
HDR-TG1/TG1E/TG3E_L2
—2—
* See the label on the AC Adaptor for other
specifications.
Rechargeable battery pack NP-FH50
Maximum output voltage: DC 8.4 V
Output voltage: DC 6.8 V
Capacity: 6.1 Wh (900 mAh)
Type: Li-ion
Design and specifications are subject to change
without notice.
• Manufactured under license from Dolby
Laboratories.
These specifications are extracted from instruction
manual of HDR-TG1.
ENGLISH
JAPANESE
SPECIFICATIONS
System
Input/Output connectors
AC Adaptor AC-L200/L200B
Video compression format: AVCHD (HD)/
MPEG2 (SD)/JPEG (Still images)
Audio compression format: Dolby Digital 2/5.1ch
Dolby Digital 5.1 Creator
Video signal: NTSC color, EIA standards
1080/60i specification
Recording format: Movie (HD): AVCHD 1080/
60i
Movie (SD): MPEG2-PS
Still image: Exif Ver.2.2*1
Image device: 3.6 mm (1/5 type) CMOS sensor
Recording pixels (still image, 4:3):
Max. 4.0 mega (2 304 × 1 728) pixels*2
Gross: Approx. 2 360 000 pixels
Effective (movie, 16:9): Approx. 1 430 000
pixels
Effective (still image, 16:9): Approx.
1 490 000 pixels
Effective (still image, 4:3): Approx. 1 990 000
pixels
Lens: Carl Zeiss Vario-Tessar
10 × (Optical), 20 ×, 120 × (Digital)
Focal length: F1.8 ~ 2.3
f=3.2 ~ 32.0 mm (5/32 ~ 1 5/16 in.)
When converted to a 35 mm still camera
For movies*3: 43 ~ 507 mm (1 3/4 ~ 20 in.)
(16:9)
For still images: 38 ~ 380 mm (1 1/2 ~ 15 in.)
(4:3)
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K),
[OUTDOOR] (5 800 K)
Minimum illumination: 5 lx (lux) ([AUTO SLW
SHUTTR] [ON], Shutter speed 1/30 sec)
A/V Remote Connector: Component/video and
audio output jack
HDMI OUT jack: HDMI mini Connector
Power requirements: AC 100 V - 240 V, 50/60 Hz
Current consumption: 0.35 - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to + 40 °C (32 °F to
104 °F)
Storage temperature: -20 °C to + 60 °C (-4 °F to +
140 °F)
Dimensions (approx.): 48 × 29 × 81 mm
(1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
excluding the projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
*1 “Exif ” is a file format for still images,
established by the JEITA (Japan
Electronics and Information Technology
Industries Association). Files in this
format can have additional information
such as your camcorder’s setting
information at the time of recording.
*2 The unique pixel array of Sony’s ClearVid
CMOS sensor and image processing
system (BIONZ) allows still image
resolution equivalent to the sizes
described.
*3 The focal length figures are actual figures
resulting from wide angle pixel readout.
LCD screen
Image: 6.7 cm (2.7 type, aspect ratio 16:9)
Total dot number: 211 200 (960 × 220)
General
Power requirements: DC 6.8 V/7.2 V (battery
pack)
DC 8.4 V (AC Adaptor)
Average power consumption: During camera
recording using the LCD with normal
brightness:
HD: 3.4 W
SD: 2.7 W
Operating temperature: 0 °C to + 40 °C (32 °F to
104 °F)
Storage temperature: -20 °C to + 60 °C (-4 °F to +
140 °F)
Dimensions (approx.): 32 × 119 × 63 mm
(1 5/16 × 4 3/4 × 2 1/2 in.) (w/h/d)
including the projecting parts
32 × 119 × 63 mm
(1 5/16 × 4 3/4 × 2 1/2 in.) (w/h/d)
including the projecting parts, and the supplied
rechargeable battery pack attached
Mass (approx.): 240 g (8 oz) main unit only
300 g (10 oz) including the supplied
rechargeable battery pack, and a “Memory
Stick PRO Duo”
Handycam Station DCRA-C230
Input/Output connectors
A/V OUT jack: Component/video and audio
output jack
USB jack: mini-B
Dedicated USB Terminal Adaptor
Input/Output connectors
USB jack: mini-B
HDR-TG1/TG1E/TG3E_L2
—3—
* See the label on the AC Adaptor for other
specifications.
Rechargeable battery pack NP-FH50
Maximum output voltage: DC 8.4 V
Output voltage: DC 6.8 V
Capacity: 6.1 Wh (900 mAh)
Type: Li-ion
Design and specifications are subject to change
without notice.
• Manufactured under license from Dolby
Laboratories.
ENGLISH
JAPANESE
概略仕様
システム
電源部、その他
リチャージャブルバッテリーパック
映像圧縮方式：AVCHD（HD）/MPEG2（SD）/JPEG
（静止画）
電源電圧：バッテリー端子入力 6.8 V/7.2 V
DC端子入力 8.4 V
NP-FH50
音声圧縮方式：Dolby Digital2/5.1ch
ドルビーデジタル5.1クリエーター搭載
消費電力：液晶画面の明るさ標準：
HD 3.4 W、SD 2.7 W
映像信号：NTSCカラー、EIA標準方式
1080/60i方式
保存温度：−20℃∼+60℃
動画記録方式：動画HD: AVCHD 1080/60i
動画SD: MPEG2-PS
静止画記録方式：Exif Ver.2.2*
1
撮像素子：3.6 mm（1/5型）CMOSセンサー
記録画像数：静止画時最大400万画素相当*2
（2 304×1 728）
（4:3時）
総画素数：約236万画素
動画時有効画素数（16：9）
：約143万画素
：約149万画素
静止画時有効画素数（16：9）
静止画時有効画素数（4：3）
：約199万画素
動作温度：0℃∼+40℃
外形寸法：32×119×63 mm
（突起部を含む）
（幅×高さ×奥行き）
32×119×63 mm
（突起部含む、付属バッテリー装着状態）
（幅×高さ×奥行き）
本体質量：約240 g（本体のみ）
撮影時総質量：約300 g（付属バッテリー、
“メモリー
スティック PRO デュオ”含む）
ハンディカムステーション
ズームレンズ：カールツァイスバリオテッサー
10倍（光学）、20倍、120倍（デジタル）
F1.8∼2.3
f=3.2∼32.0 mm
35mmカメラ換算では
動画撮影時*3：
43∼507 mm（16:9）
静止画撮影時：
38∼380 ｍｍ（4:3）
DCRA-C230
色温度切り換え：
［オート］、
［ワンプッシュ］、
［屋内］
（3 200 K）、
［屋外］
（5 800 K）
入/出力端子
最低被写体照度：5 lx（ルクス）
（［オートスロシャッ
タ］
［入］、
［シャッタースピード］
1/30秒）
入/出力端子
A/V OUT端子：コンポーネント、映像音声出力兼用端
子
USB端子：mini-B
専用USB端子アダプター
USB端子：mini-B
ACアダプター AC-L200/L200B
*1（社）電子情報技術産業協会（JEITA）にて
電源：AC 100 V-240 V、50/60 Hz
制定された、撮影情報などの付帯情報を追
加することができる静止画用のファイル
フォーマット。
2
* ソニー独自のクリアビッドCMOSセン
サーの画素配列と画像処理システム
BIONZにより、静止画は表記の記録サイ
ズを実現しています。
*3 広角画素読み出しによる実動作値
消費電力：18 W
入/出力端子
A/Vリモート端子：コンポーネント、映像音声出力兼
定格出力：DC 8.4 V *
動作温度：0℃∼+40℃
保存温度：−20℃∼+60℃
外形寸法：約 48×29×81 mm
（最大突起部をのぞく）
（幅×高さ×奥行き）
質量：約170 g（本体のみ）
* その他の仕様については AC アダプターのラ
ベルをご覧ください。
用端子
HDMI OUT端子：HDMIミニコネクタ
液晶画面
画面サイズ：6.7 cm（2.7型、アスペクト比16:9）
総ドット数：211 200ドット
横960×縦220
HDR-TG1/TG1E/TG3E_L2
—4—
最大電圧：DC 8.4 V
公称電圧：DC 6.8 V
容量：6.1 Wh（900 mAh）
使用電池：Li-ion
本機の仕様および外観は、改良のため予告なく変
更することがありますが、ご了承ください。
• ドルビーラボラトリーズからの実施権に基づ
き製造されています。
Model information table
Model
Destination
Color system
Data CAM → PC
copy PC → CAM
HDR-TG1
US, CND, E
KR, JE, J
HDR-TG1E
NE, E, AUS,
HK, CH, JE
HDR-TG3E
NTSC
a
PAL
a
PAL
a
a
a
×
AEP, UK, NE
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-TG1/TG1E/TG3E_L2
—5—
ENGLISH
JAPANESE
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HDR-TG1/TG1E/TG3E_L2
—6—
ENGLISH
JAPANESE
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
サービス，点検時には次のことにご注意下さい。
6. フレキシブルプリント基板の取扱いについて
1. 注意事項をお守りください。
サービスのとき特に注意を要する個所については，
キャビネット，シャーシ，部品などにラベルや捺印で
• コテ先温度を270℃前後にして行なって下さい。
• 同一パターンに何度もコテ先を当てないで下さい。
注意事項を表示しています。これらの注意書き及び取
扱説明書等の注意事項を必ずお守り下さい。
（3回以内）
• パターンに力が加わらないよう注意して下さい。
2. 指定部品のご使用を
セットの部品は難燃性や耐電圧など安全上の特性を
7. 無鉛半田について
無鉛半田を使用している基板には，無鉛（Lead Free）を意
持ったものとなっています。従って交換部品は，使用
されていたものと同じ特性の部品を使用して下さい。
味するレッドフリーマークがプリントされています。
（注意：基板サイズによっては，無鉛半田を使用して
特に回路図，部品表に0印で指定されている安全上重要
な部品は必ず指定のものをご使用下さい。
いてもレッドフリーマークがプリントされて
いないものがあります）
3. 部品の取付けや配線の引きまわしはもとどおりに
安全上，チューブやテープなどの絶縁材料を使用した
：レッドフリーマーク
無鉛半田には，以下の特性があります。
り，プリント基板から浮かして取付けた部品がありま
す。また内部配線は引きまわしやクランパによって発
• 融点が従来の半田よりも約40℃高い。
従来の半田こてをそのまま使用することは可能です
熱部品や高圧部品に接近しないよう配慮されています
ので，これらは必ずもとどおりにして下さい。
が，少し長めにこてを当てる必要があります。
温度調節機能のついた半田こてを使用する場合，約
4. サービス後は安全点検を
サービスのために取外したネジ，部品，配線がもとど
350℃に設定して下さい。
注意：半田こてを長く当てすぎると，基板のパター
おりになっているか，またサービスした個所の周辺を
劣化させてしまったところがないかなどを点検し，安
ン（銅箔）がはがれてしまうことがあります
ので，注意して下さい。
• 粘性が強い
従来の半田よりも粘性が強いため，IC端子などが半田
全性が確保されていることを確認して下さい。
5. チップ部品交換時の注意
• 取外した部品は再使用しないで下さい。
• タンタルコンデンサのマイナス側は熱に弱いため交
ブリッジしないように注意して下さい。
• 従来の半田と混ぜて使用可能
無鉛半田には無鉛半田を追加するのが最適ですが，
従来の半田を追加しても構いません。
換時は注意して下さい。
HDR-TG1/TG1E/TG3E_L2
—7—
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. PRECAUTION ON REPLACING THE VC-522 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function
1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD
screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
Viewfinder or LCD screen
C:31:11
Blinks at 3.2 Hz
C
Repaired by:
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
31
Block
11
Detailed Code
Refer to “1-3-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
HDR-TG1/TG1E/TG3E_L2
1-1
ENGLISH
JAPANESE
1-3-3. Self-diagnosis Code Table
Repaired by:
Self-diagnosis Code
Block
Function
Detailed
Code
Symptom/State
C
0
4
0
0
C
1
3
0
1
C
1
3
0
2
Access error
C
3
2
6
0
Difficult to adjust focus
(Cannot initialize focus)
E
2
0
0
0
Flash memory data are rewritten.
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
E
6
1
1
1
E
6
2
0
0
E
6
2
0
1
E
9
1
0
1
E
9
4
0
0
Correction
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality when flash is being charged.
Fault of writing to or erasing the flash
memory
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source.
Reconnect it again and operate your camcorder again.
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin 1, 2 of
CN5202 on the LD-235 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-235 board).
Make flash memory data correct value. (Note 1)
Inspect the lens block zoom reset sensor (pin wf of CN5202 on
the LD-235 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5201 on
the LD-235 board) when zooming is not performed.
Check both C : 32 : 60 and E : 61 : 10 of the self-diagnosis code.
Inspect PITCH/YAW angular velocity sensors (SE6602 on the
SE-174 board) peripheral circuits.
Inspect PITCH/YAW angular velocity sensors (SE6602 on the
SE-174 board) peripheral circuits.
Checking of flash unit or replacement of flash unit.
Inspect the flash memory (IC2101 on the VC-522 board).
Note 1: Refer to Service manual, ADJ (“1-3. DESTINATION DATA WRITE”).
Note 2: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
HDR-TG1/TG1E/TG3E_L2
1-2
ENGLISH
JAPANESE
1-4. PRECAUTION ON REPLACING THE CABINET (L)
1-4-1. Precaution on ordering the Cabinet (L)
Note: After replacing the Cabinet (L), the serial number for it will
be changed to the one exclusive for service use.
Inform a customer of the serial number change and change
the serial number in the repair data.
The model display adopts the laser printing method.
Therefore, the Cabinet (L) for replacement differs depending on
the destination.
As similar displays are provided, choose the suitable one for order.
HDR-TG1 (J)
Serial No.
Part No.
HDR-TG1 (US)
Description
A-1542-400-A CABINET (L (TG1-J1)),
SERVICE
HDR-TG1 (KR)
Serial No.
Part No.
Description
A-1542-404-A CABINET (L (TG1-KR2)),
SERVICE
HDR-TG1E (E, HK, AUS, JE)
Serial No.
Part No.
Description
A-1542-407-A CABINET (L (E34)),
SERVICE
Serial No.
Part No.
HDR-TG1 (CND)
Description
A-1542-402-A CABINET (L (TG1-U2)),
SERVICE
HDR-TG1 (E, JE)
Serial No.
Part No.
Description
A-1542-405-A CABINET (L (TG1-E23)),
SERVICE
HDR-TG1E (CH)
Serial No.
Part No.
Description
A-1542-408-A CABINET (L (CN2)),
SERVICE
HDR-TG3E (AEP, UK)
Serial No.
Part No.
Description
A-1542-410-A CABINET (L (TG3-CEN)),
SERVICE
HDR-TG1/TG1E/TG3E_L2
1-3
Serial No.
Part No.
Description
A-1542-403-A CABINET (L (TG1-CA2)),
SERVICE
HDR-TG1E (NE)
Serial No.
Part No.
Description
A-1542-406-A CABINET (L (TG1-CEL)),
SERVICE
HDR-TG3E (NE)
Serial No.
Part No.
Description
A-1542-409-A CABINET (L (TG3-CEL)),
SERVICE
ENGLISH
JAPANESE
1-4-2. Precaution on Replacing the Cabinet (L) for J Models
The year of manufacture on the labels should be the same as the previous Cabinet (L) (circled portions shown on the below).
Example: For the figure below, attach the “Made of 08 years” label.
* The replacement label and “inset (how to affix)” are supplied together with Cabinet (L) for service.
* Manufacturing year
* Affix the label
1-4-3. Precaution on Replacing the Cabinet (L) for US Models
The date of manufacture and the manufacturer on the labels should be the same as the previous Cabinet (L) (circled portions shown on the
below).
Example: For the figure below, attach the “8A” and “SKD” labels.
* The replacement labels and “inset (how to affix)” are supplied together with Cabinet (L) for service.
* Manufacturing year
* Factory
* Affix the label
1-4-4. Precaution on Replacing the Cabinet (L) for KR Models
The date of manufacture on the labels should be the same as the previous Cabinet (L) (circled portions shown on the below).
Example: For the figure below, attach the “2008.2” label.
* The replacement label and “inset (how to affix)” are supplied together with Cabinet (L) for service.
* Manufacturing year
* Affix the label
HDR-TG1/TG1E/TG3E_L2
1-4
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L200/L200B）を使用する。）
1-2. VC-522基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
1-3. 自己診断機能
1-3-2. 自己診断表示
1-3-1. 自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，
本機の動作に不具合が生じたとき，ビューファインダまたは
LCD画面のカウンタ表示部分がアルファベットと数字の4桁
ビューファインダまたはL C D 画面に，どう処置したらよい
か判断できる表示を行います。自己診断機能については取扱
表示になり，3.2Hzで点滅します。この5文字の表示によっ
て対応者分類および不具合の生じたブロックの分類，不具合
説明書にも掲載されています。
の詳細コードを示します。
ビューファインダまたはLCD画面
C:31:11
3.2Hz点滅
C
対応者分類
C ：お客さま自身で対応
H ：販売店で対応
E ：サービスエンジニア
で対応
31
ブロック分類
11
詳細コード
対応方法の違いにより分類「1-3 -3 . 自己診断コード表」
例 31 ･･･テープを入れ直すを参照
32 ･･･電源を入れ直す
HDR-TG1/TG1E/TG3E_L2
1-5
ENGLISH
JAPANESE
1-3-3. 自己診断コード表
自己診断コード
対ブロック
応
機能
者
詳細
コード
C
0
0
4
症状／状態
対応／方法
0
標準以外のバッテリを使用しているインフォリチウムバッテリを使用する。
C
1
3
0
1
フォーマットしていない“メモリー “メモリーステックデュオ”をフォーマットする。
ステックデュオ”を入れた
“メモリーステックデュオ”が壊新しい“メモリーステックデュオ”に交換する。
れている
C
1
3
0
2
アクセスエラー
電源を外し，再度入れ直してから操作する。
C
3
2
6
0
操作スイッチの電源を入れ直す。
復帰しない場合，レンズブロックのフォーカスMRセンサ
フォーカスが合いにくい
（LD-235基板CN5202 1，2ピン）を点検する。異常なけ
（フォーカスの初期化ができない）
ればフォーカスモータ駆動回路（LD-235基板IC5201）を
点検する。
E
2
0
0
0
フラッシュメモリが書き換えられて
フラッシュメモリのデータを元の値に戻す。（注意1）
いる
E
6
1
1
0
ズームレバーを操作したときにズーム動作をすれば，レン
ズーム動作の異常（ズームレンズのズブロックのズームリセットセンサ（LD-235基板CN5202
初期化ができない）
wfピン）を点検する。ズーム動作をしなければズームモー
タ駆動回路（LD-235基板IC5201）を点検する。
E
6
1
1
1
フォーカス，ズーム異常
自己診断コードC：32：60とE：61：10の両方を点検す
る。
E
6
2
0
0
手振れ補正が効きにくい（PITCH
角速度センサ出力張り付き）
PITCH/YAW角速度センサ（SE-174基板SE6602）周辺回路
を点検する。
E
6
2
0
1
手振れ補正が効きにくい（YAW 角
速度センサ出力張り付き）
PITCH/YAW角速度センサ（SE-174基板SE6602）周辺回路
を点検する。
E
9
1
0
1
フラッシュの充電異常
フラッシュユニットの点検または交換をする。
E
9
4
0
0
フラッシュメモリの書込み/消去動
作不良
フラッシュメモリ（VC-522基板IC2101）を点検する。
注意 1： ADJ編，（「1-3. DESTINATION DATA WRITE」）を参照してください。
注意 2：レンズブロックを交換した場合は，ADJ編を参照して必要な調整項目を実施すること。調整後は手振れ補正ONの状
態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-TG1/TG1E/TG3E_L2
1-6
ENGLISH
JAPANESE
1- 4. キャビネット（L）交換時の注意
1-4-1. キャビネット
（L）注文時の注意
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット（L）は機種，仕向けにより
異なります。類似の表示もありますので，該当するものを
選んで注文してください。
HDR-TG1 (J仕向)
シリアルナンバー
部品コード
部品名
A-1542-400-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (TG1-J1))
HDR-TG1 (KR仕向)
シリアルナンバー
部品コード
部品名
A-1542-404-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (TG1-KR2))
HDR-TG1E (E, HK, AUS, JE仕向)
シリアルナンバー
部品コード
部品名
A-1542-407-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (E34))
注意：キャビネット（L）交換後はシリアルナンバーがサー
ビス専用のシリアルナンバーに変更されます。お客
様への案内と修理データのシリアルナンバー変更を
行ってください。
HDR-TG1 (US仕向)
シリアルナンバー
部品コード
部品名
A-1542-402-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (TG1-U2))
HDR-TG1 (E, JE仕向)
シリアルナンバー
部品コード
部品名
A-1542-405-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (TG1-E23))
HDR-TG1E (CH仕向)
シリアルナンバー
部品コード
部品名
A-1542-408-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (CN2))
HDR-TG3E (AEP, UK仕向)
シリアルナンバー
部品コード
部品名
A-1542-410-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (TG3-CEN))
HDR-TG1/TG1E/TG3E_L2
1-7
HDR-TG1 (CND仕向)
シリアルナンバー
部品コード
部品名
A-1542-403-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (TG1-CA2))
HDR-TG1E (NE仕向)
シリアルナンバー
部品コード
部品名
A-1542-406-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (TG1-CEL))
HDR-TG3E (NE仕向)
シリアルナンバー
部品コード
部品名
A-1542-409-A ｻ-ﾋﾞｽ用ｷｬﾋﾞ (L (TG3-CEL))
ENGLISH
JAPANESE
1-4-2. 日本向けモデルのキャビネット（L）交換時の注意
交換前のキャビネット（L）に印字されている“製造年（下図の○部の表示）”と同じ表示のラベルを新しいキャビネット（L）に
貼付けてください。
例：下図では，“08年製”のラベルを貼る
* ラベルは，サービス用キャビネット（L）部組に「投げ込み（ラベル貼り方）」を含めて同梱されています。
* 製造年
* ラベルを貼付けてください
1-4-3. US向けモデルのキャビネット
（L）交換時の注意
交換前のキャビネット（L）に印字されている“製造年月（下図の○部の表示）”と同じ表示のラベルを新しいキャビネット（L）
に貼付けてください。
例：下図では，“8A”と“SKD”のラベルを貼る
* ラベルは，サービス用キャビネット（L）に「投げ込み（ラベル貼り方）」を含めて同梱されています。
* 製造年
* 製造所
* ラベルを貼付けてください
1-4-4. 韓国向けモデルのキャビネット（L）交換時の注意
交換前のキャビネット（L）に印字されている“製造年月（下図の○部の表示）”と同じ表示のラベルを新しいキャビネット（L）
に貼付けてください。
例：下図では，“2008.2”のラベルを貼る
* ラベルは，サービス用キャビネット（L）に「投げ込み（ラベル貼り方）」を含めて同梱されています。
* 製造年
* ラベルを貼付けてください
HDR-TG1/TG1E/TG3E_L2
1-8E
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
DISCHARGING OF FP-914 FLEXIBLE BOARD’S CHARGING CAPACITOR (C001)
The charging capacitor (C001) of FP-914 flexible board is
charged up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
1 kΩ/1 W
Wrap insulating tape.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
FP-914
Flexible Board
HDR-TG1/TG1E/TG3E_L2
2-1
2-1. IDENTIFYING PARTS
Control Switch Block
(PS27500)
Top Cabinet
Inner (Top) Cabinet
Lens Block
⋅ CM-096 Board
⋅ FP-910 Flexible Board
⋅ LD-235 Board
Main Frame
⋅ FP-902 Flexible Board
⋅ FP-903 Flexible Board
⋅ FP-905 Flexible Board
⋅ FP-906 Flexible Board
⋅ FP-907 Flexible Board
⋅ FP-911 Flexible Board
⋅ FP-912 Flexible Board
⋅ FP-913 Flexible Board
⋅ FP-915 Flexible Board
⋅ FP-916 Flexible Board
⋅ FP-917 Flexible Board
⋅ MD-137 Board
⋅ MS-396 Board
⋅ SE-174 Board
⋅ ST-186 Board
⋅ VC-522 Board
Cabinet (L)
LCD Panel Block
⋅ FP-909 Flexible Board
Cabinet (R) Block
Front Cabinet
⋅ FP-904 Flexible Board
⋅ FP-908 Flexible Board
⋅ FP-914 Flexible Board
- DISASSEMBLY FLOW 2-2-1. OVERALL SECTION
⋅ Cabinet (L)
⋅ Control Switch Block (PS27500)
⋅ Inner (Top) Cabinet
2-2-2. Front Cabinet Section
⋅ Front Cabinet
⋅ Flash Unit
⋅ MS-396 Board
2-2-3. Main Frame Section-1
⋅ FP-907 Flexible Board
⋅ Cabinet (R) Block
⋅ SE-174 Board
2-2-4. Main Frame Section-2
⋅ ST-186 Board
⋅ MD-137 Board
⋅ Lens Block
2-2-5. Cabinet (R) Section
⋅ JK Holder Block
⋅ Capacitor Block
⋅ LCD Panel Block
HDR-TG1/TG1E/TG3E_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW
HARDWARE LIST
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1 Cabinet (L) (1-1 to 1-5)
2 Control Switch Block (PS27500) (2-1 to 2-3)
3 Inner (Top) Cabinet (3-1 to 3-9)
2 Control Switch Block
(PS27500)
2-1
(#14)
3-2
(Boss)
3-3
2-3
3-8 (#14)
3-6
2-2
1 Cabinet (L)
1-5 (#2)
1-2 (#2)
3-5
3-4 (#14)
3-1 (#2)
3-9
(Boss)
3-7
1-4
(Open)
3 Inner (Top) Cabinet
1-3 (#2)
1-1
(Open)
Front Cabinet Section
(See Page 2-4)
HDR-TG1/TG1E/TG3E_L2
2-3
2-2-2. FRONT CABINET SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 Front Cabinet (1-1 to 1-5)
2 Flash Unit (2-1 to 2-3)
3 MS-396 board (3-1 to 3-6)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
2-1
2 Flash Unit
FP-914
Flexible Board
2-3
3-3
3-1
3-5
(#14)
2-2 (#14)
3 MS-396 Board
1-3 (#5)
3-6 (#3)
3-2
6
-39
MS
3-4
1-2 (#14)
1-5
1-1 (#14)
Main Frame Section-1
(See Page 2-5)
1-4 (Claw)
1 Front Cabinet
HDR-TG1/TG1E/TG3E_L2
2-4
2-2-3. MAIN FRAME SECTION-1
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 FP-907 Flexible Board (1-1 to 1-4)
2 Cabinet (R) Block (2-1 to 2-6)
3 SE-174 Board (3-1 to 3-9)
Main Frame Section-2
(See Page 2-6)
3 SE-174 Board
2-5 (#14)
3-6
(#3)
3-9
3-3
(#3)
3-7
(Claw)
3-5 (#14)
3-4
(#14)
1-2
HELP 1
2-6
(#14)
3-8
3-2 (#3)
2-1
1-3 (#14)
2-4
(#14)
3-1
1-1
1-4
(Claw)
2-2
2 Cabinet (R) Block
(See Page 2-7)
2-3
1 FP-907 Flexible Board
HDR-TG1/TG1E/TG3E_L2
2-5
2-2-4. MAIN FRAME SECTION-2
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 ST-186 Board (1-1 to 1-4)
2 MD-137 Board (2-1 to 2-6)
3 Lens Block (3-1 to 3-3)
2-1
1 ST-186 Board
2-2 (#3)
HELP 4
1-2 (#3)
7
-13
MD
1-3
(Claw)
1-1
3 Lens Block
1-4
2-3
(Claw)
2-6
HELP 3
2 MD-137 Board
3-1
3-2
2-5
2
-52
VC
2-4 (#3)
3-3
HELP 2
HDR-TG1/TG1E/TG3E_L2
2-6
2-2-5. CABINET (R) SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 JK Holder Block (1-1 to 1-5)
2 Capacitor Block (2-1 to 2-2)
3 LCD Panel Block (3-1 to 3-13)
3-11
3-10 (#14)
3-12 (#14)
3 LCD Panel Block
1 JK Holder Block
3-1 (#14) 3-2
1-1
(#14)
3-3
3-7
3-6
3-4
1-3
(#2)
3-5
(#14)
1-4
3-8
HELP 1
3-9
1-5
3-13
1-2 (#2)
2-2
(#2)
2 Capacitor Block
2-1
HDR-TG1/TG1E/TG3E_L2
2-7E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP 1: DC Jack Harness
Hook
DC Jack Harness
FP-914 Flexible Board
FP-908 Flexible Board
DC Jack Harness
BT Frame Hook
Terminal Retainer Hook
HELP 2: Radiation Sheet (A)/AG Copy Sheet
Radiation Sheet (A)
HELP 3: FP-917 Flexible Board
AG Copy Sheet
Apply the fold habit.
Valley fold
AG Copy Sheet
VC-522 Board
HDR-TG1/TG1E/TG3E_L2
HELP
HELP 4: The Method of Attachment of ST-186 Board
1 Apply folds to the FP-915 flexible board as shown in 4 Prepare the stand of about 20 mm in height, and
the figure below.
set it as shown in the figure below.
2 Install the FP-915 flexible board to CN7503 of
5 Install the FP-915 flexible board to CN1112 of
ST-186 board.
MD-137 board.
6 Insert the claw of ST-186 board in the main frame.
CN7503 of ST-186 Board (Side A)
7 Tighten the screw.
6 Claw
7 Screw
ST-186 Board
1 Fold
2 FP-915 Flexible Board
5 FP-915 Flexible Board
1 Fold
3 Install the FP-912 flexible board to CN7501 of
ST-186 board.
CN7501 of ST-186 Board (Side B)
About 20 mm
3 FP-912 Flexible Board
4 Stand
CN1112 of MD-137 Board (Side A)
8 Install the FP-912 flexible board to CN1026 of
VC-522 board.
8 FP-912 Flexible Board
CN1026 of VC-522 Board (Side A)
HDR-TG1/TG1E/TG3E_L2
HELP
HELP 5: The Method of Attachment of FP-909 Flexible Board
1 Apply folds to the FP-909 flexible board as shown in 5 Install the hinge clamp to the FP-909 flexible board.
the figure below.
6 Install the hinge assy to the hinge clamp.
2 Stick adhesive tapes.
3 Match the position of the hole, and stick adhesive
tapes.
4 Paste the JN copy sheet.
5 Hinge clamp
1 Mountain fold 2 Adhesive tape
6 Hinge assy
1 Valley fold
1 Mountain fold
2 Adhesive tape
1 Valley fold
7 Rotate the hinge assy.
8 Match the position of the boss, and stick adhesive
tapes.
9 Rotate the hinge clamp, and fix the FP-909 flexible
board.
7
8 Boss
3 Adhesive tape
9 Hinge clamp
0 Install the hinge cover (rear).
Note: Confirm the FP-909 flexible board is fixed.
qa Tighten the screw.
qa Screw
0 Hinge cover (rear)
Match the position
of the hole
4 JN Copy Sheet
HDR-TG1/TG1E/TG3E_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/7)
OVERALL BLOCK DIAGRAM (6/7)
OVERALL BLOCK DIAGRAM (2/7)
OVERALL BLOCK DIAGRAM (7/7)
OVERALL BLOCK DIAGRAM (3/7)
POWER BLOCK DIAGRAM (1/3)
OVERALL BLOCK DIAGRAM (4/7)
POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (5/7)
POWER BLOCK DIAGRAM (3/3)
HDR-TG1/TG1E/TG3E_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/7)
LENS BLOCK
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-522 BOARD (1/6)
CM-096 BOARD
14, 16
14, 16
XVS, XHS
IC_1301_SDO, SCK, XCE
INCK
SENS_DATA_P_5,
SENS_DATA_M_5
4M_DOBP/10M_DODP,
4M_DOBM/10M_DODM
SENS_DATA_P_4,
SENS_DATA_M_4
4M_DOCP/10M_DOEP,
4M_DOCM/10M_DOEM
SENS_DATA_P_3,
SENS_DATA_M_3
4M_DODP/10M_DOFP,
4M_DODM/10M_DOFM
SENS_DATA_P_2,
SENS_DATA_M_2
32, 34
26, 28 38, 40
XCLR
CN1303
4M_DOAP/10M_DOCP,
4M_DOAM/10M_DOCM
20, 22
20, 22
32, 34
DCKP, DCKM
26, 28 38, 40
4M_DODP/10M_DOFP,
4M_DODM/10M_DOFM
3
3
10, 5
M9
4M_DOCP/10M_DOEP,
4M_DOCM/10M_DOEM
6, 8, 4
K5, K4, L6 K3, J3
K2
4M_DOBP/10M_DODP,
4M_DOBM/10M_DODM
10, 5
H10,
H11
F10,
F11
4M CMOS
IMAGER
CN6902
4M_DOAP/10M_DOCP,
4M_DOAM/10M_DOCM
6, 8, 4
IC6904
G10,
G11
J10,
J11
K10,
K11
IRIS
(SHUTTER)
9
9
SENS_CLK_P,
SENS_CLK_M
DCKP, DCKM
2
OVERALL (2/7)
(PAGE 3-2)
XCLR
SENS_VD, SENS_HD
XVS, XHS
IC_1301_SDO, SCK, XCE
IC_1301_SDO, SENSSCK, SENSXCS
INCK
XFLASH_RST
3
OVERALL (6/7)
(PAGE 3-6)
LD-235 BOARD
IRIS
MOTOR
SYSTEM_CLOCK
7, 1
ZOOM_A,
ZOOM_B,
ZOOM_XA,
ZOOM_XB
ZOOM MOTOR
M
IC5204
FOCUS MOTOR
NOISE FILTER
2, 1
TG1E/TG3E
6–9
F_MR_A,
F_MR_B
FOCUS MR
SENSOR
2
E3
LENS TEMP
SENSOR
ZM_RST_SENS
LENS_DETE
LENS_TEMP_OUT
24
26
5
CLOCK
GENERATOR
(1/12)
2
14
PITCH/YAW 12
SENSOR
CAM_SO, CAM_SI, XCAM_SCK
XCS_IC_5201
XRST_IC_5201
5
CN6601
(1/2)
PITCH_AD
8
YAW_AD
10
VST_C_RST
6
FP-911 FLEXIBLE
BOARD (1/2)
CN1029
(1/2)
4
2
6
PITCH_AD
YAW_AD
VST_C_RST
4
OVERALL (2/7)
(PAGE 3-2)
IC_5201_CLK
A : VIDEO SIGNAL
FOCUS
MOTOR
DRIVE
1
ZOOM MOTOR
DRIVE
LEN COVER
MOTOR DRIVE
L8
M8
OVERALL (2/7)
(PAGE 3-2)
EN1, DIRA1, DIRB1
LENS_COVER_DRV_ON
LENS_COVER_DIR_PWM
SHUTTER_A,
SHUTTER_XA
ZOOM RESET
SENSOR
7
16
18
SE6602
IC_5201_VD
F3, E3
10, 11
FOCUS±
M
XCS_IC_5201
XRST_IC_5201
IC_5201_CLK
10 – 8
C5, B6 C6, A5 H1, J1
TG1
FOCUS MOTOR
J12
H11
K12
CAM_SO, CAM_SI, XCAM_SCK
21
ZM_RST_SENS
LENS_DETE
LENS_TEMP_AD
15 – 13
ND_HALL±
IC_5201_VD
20
22
32, 33, 29, 30
H
ND FILTER
DRIVE
J11, K11, H12
ND_BIAS±
K9, L9, M9, J9
ND_DRIVE±
M
SE-174 BOARD (1/2)
FP-910 FLEXIBLE BOARD
CN5201
L12
C10, B11 A11, A9 K2, L2
ND FILTER
MOTOR
IRIS
DRIVE
B1, C4
I_HALL±
K6, F1,
L4, G3
H
4
IC5201
L6, L7
I_BIAS±
17, 15 16, 14 12, 13
I_DRIVE±
M
19, 23 18, 22 21, 20
CN5202
X1301
48MHz
IC1303
23
24
25
EN1, DIRA1, DIRB1
LENS_COVER_DRV_ON
LENS_COVER_DIR_PWM
SHUTTER_A,
SHUTTER_XA
ZM_RST_SENS
LENS_DETE
LENS_TEMP_AD
05
HDR-TG1/TG1E/TG3E_L2
3-1
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-522 BOARD (2/6)
CN1033
IC_5201_VD
EN1, DIRA1, DIRB1
LENS_COVER_DRV_ON
20
7, 8, 10, 11
C20, D20, A17 B19, D19, D18, D16, C16, A15,
A19, C18, C19, B15, B16, B17,
D17, C17
C15, D15
IC_2201_IVCLK
IC_2201_SYSCLK
IC_2201_FLD
6, 7, 9, 10
3
2
AA16
IC_2201_MCK
IC_2201_LRCK
H32
H33
AE11
SHUTTER_A,
SHUTTER_XA
IC2201
AUDIO/VIDEO
CODEC
(8/12)
AC16
AB16
IC1702
AP19
AR16
AR17
AM19
X1701
12MHz
AC12
BUFFER
(4/12)
B3
PCI_AD0 – PCI_AD31
PCI_XBE0 – PCI_XBE3
N5
P2
N1
PCI_XRESET
PCI_XRESET
PCI_CLK
PCI_CLKRUN
PCI_CLK
PCI_CLKRUN
H1
J1
A4
AA17
CN1011
LENS
BARRIER
UNIT
AC8
AC13
AB12
IC_2201_ADATA
J33
AA11, AB11, AB10,
AA10, Y11,
Y8, AB9, AC9
U4, R5, U5,
V1, V2, T4,
T5, R4
AJ14, AH14
Y2, V5, Y1,
W5, W4, W1,
W2, V4
PCI_XBE0 – PCI_XBE3
AE7
LENS_TEMP_AD
15
IC_2201_DATA0 – IC_2201_DATA7
K35
L35
K34
PCI_AD0 – PCI_AD31
IC_2201_DDR_CLK
M23
XIC_2201_DDR_CLK
N23
XIC_2201_DDR_CS0
N22
AF24
LENS_DETE
16
G2
H7
AF1
ZM_RST_SENS
17
IC_1301_DDR2_CLK
IC_1301_DDR2_XCS_0
G2
G3
H7
AH5
LENS_COVER_DIR_PWM
18
AJ15, AH15
AC2
AF5
AJ3
256M
SDRAM
(3/12)
IC1301
A13
B13
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
MODE CONTROL
(4/12 – 6/12)
AJ26, AF22,
AC23
25 – 27
1
CAM_SO, CAM_SI, XCAM_SCK
XCS_IC_5201
XRST_IC_5201
IC_5201_CLK
33
24
22
OVERALL (1/7)
(PAGE 3-1)
AC18
Y7, AB5, AC1
30 – 32
19
IC_1301_DDR2_ADDR_0 –
IC_1301_DDR2_ADDR_13
CAMERA SIGNAL PROCESSOR,
CAMERA CONTROL
(1/12, 2/12)
512M
SDRAM
(9/12)
IC1701
(1/5)
IC1601
IC_2201_DDR_A00 –
IC_2201_DDR_A13
IC2301
M32, M33, L32,
L33, L34, K32,
K33, J32
IC_1301_SDO, SENSSCK, SENSXCS
IC_2201_DDR_D00 –
IC_2201_DDR_D31
B20
A20
H24
B23
D25
AM16, AN16, AM22 – AM29,
AM17, AP15 AN22 – AN29,
AP22 – AP29,
AR22 – AR29
SENS_VD, SENS_HD
EXT_CAM_VD
EXT_CAM_CLK
XIC_1301_COM_REQ
XRESET_REQ
SYS_V
IC_1301_DDR2_DATA_0 –
IC_1301_DDR2_DATA_31
AF19, AJ23
SENS_CLK_P,
SENS_CLK_M
AC19, AE19, AH22
OVERALL (1/7)
(PAGE 3-1)
VIN_HD, VIN_VD, VIN_FLD
AF20
U1
U7
AE1
AB4
AJ16, AH16
2
VIN_C0 – VIN_C7
Y4, Y5,
AA1
SENS_DATA_P_2,
SENS_DATA_M_2
VIN_Y0 – VIN_Y7
K5, K4, J1, J2, M7, J5, J4, H1,
K7, H2, L7, H5, H4, G1, G2, J7,
L4, K1, G5, G4, F1, F2, H7, F5, F4, E1,
M4, K2 G7, E2, E5, E4, D1, D5, D2. D4
SENS_DATA_P_3,
SENS_DATA_M_3
AJ17, AH17
SENS_DATA_P_4,
SENS_DATA_M_4
A : VIDEO SIGNAL
A : AUDIO SIGNAL
AJ18, AH18
SENS_DATA_P_5,
SENS_DATA_M_5
T3, M3, W3, W2, V2, V1,
J2, E2 U2, U1, U3, T1,
T2, R3, R2, P2,
P1, P3, N1, N2,
H3, H2, H4, G2,
G4, G3, E4, E1,
D3, D1, D4, D2,
C4, C1, C3, C2
3-2. OVERALL BLOCK DIAGRAM (2/7)
SPDIF_O
SHUTTER_A,
SHUTTER_XA
6
IC1705
LENS_COVER_OPEN
BUFFER
(4/12)
AJ4
LENS_COVER_CLOSE
AE4
4
OVERALL (1/7)
(PAGE 3-1)
PITCH_AD
YAW_AD
VST_C_RST
AH9
AF11
AB9
STRB_CHARGE
XSTRB_FULL
STROBE_ON
AC11
AJ5
AE20
D1301
AC5
XSYS_RST
5
OVERALL (6/7)
(PAGE 3-6)
05
HDR-TG1/TG1E/TG3E_L2
3-2
CLK_SYS_OUT_CEC
OVERALL (3/7)
(PAGE 3-3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
Q2406 – Q2408
IC_2401_Y_OUT
IC_2401_C/PB_OUT
IC_2401_PR_OUT
BUFFER
7
OVERALL (4/7)
(PAGE 3-4)
BB_SI, BB_SO, XBB_SCK
PANEL_R
PANEL_G
PANEL_B
PANEL_R
PANEL_G
PANEL_B
BUFFER
K1, K2
AA2
AA4
AA5
Q2403 – Q2405
8
OVERALL (5/7)
(PAGE 3-5)
PANEL_HD, PANEL_VD
FP-903 FLEXIBLE
BOARD (1/3)
IC2401
CN1037
(1/3)
DOWN
CONVERTER
(10/12)
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
MD-137 BOARD (1/3)
CN9034
CN9102
CN1102
(1/3)
(1/3)
(1/3)
IC_2401_Y_OUT
IC_2401_Y_OUT
58 58
24 24
IC_2401_C/PB_OUT
IC_2401_C/PB_OUT
60 60
22 22
BB_SO, XBB_SCK
9
OVERALL (4/7)
(PAGE 3-4)
CN1110
(1/4)
HMCK
HM74CK
HM_FLD
29 29
32 32
XCS_IC_2601
XHDMI_RST
OVERALL (4/7)
(PAGE 3-4)
FP-902 FLEXIBLE
BOARD (1/3)
I2C_SDA, I2C_SCK
CEC_INT
CN9101
(1/3)
ADA_FCK
ADA_BCK
ADA_LRCK
CN1101
(1/3)
SPDIF_O
10 10
CLK_SYS_OUT_CEC
9 9
41, 43
41, 43
OVERALL (2/7)
(PAGE 3-2)
CN1036
CN9022
(1/3)
(1/3)
SPDIF_O
42 42
CLK_SYS_OUT_CEC
41 41
7, 9
7, 9
6
AR13, AR12
A9, A10,
B9 – B12,
C12, D12
K5, K4, K8,
K7, J10, K10
15, 14, 19, 18, 23, 22
K2, K1
11, 10
B1, A1, B2, A2,
B3, A3, B4, A4,
B5, A5, B6, A6,
B7, A7, B8, A8,
B9, A9, B10, A10,
C9, C10, D9, D10
A2 – A4,
B2 – B4,
C1, D1
J1, K1, K2, K12,
L1 – L11, M3 – M11
J9, K10
C1, D2
IDCK
F12
H12
D1
44 44
8 8
I2C_SDA, I2C_SCK
HDMI
TRANSMITTER
(2/7)
CN1001
HDMI OUT
C2
F4
C11
D10
E10
E11
G11
F10
J10
ADAO1_HDMI, ADAO2_HDMI
256FS_HDMI
64FS_HDMI
FS_HDMI
E1
H2
H1
SPDIF_O
CLK_SYS_OUT_CEC
E2
G7
H10
J8
I2C_SDA, I2C_SCK
CEC_INT
CEC_INT
5, 6
51 51
50 50
BB_SI, BB_SO, XBB_SCK
ADA_SIA0
CEC_INT
HSYNC_HDMI, VSYNC_HDMI
G9, G10
XCS_IC_2601
XHDMI_RST
11
D31
E1
G1
C4
HDMI
SIGNAL
PROCESSOR
(1/7)
IC2701
BB_SI, BB_SO, XBB_SCK
I2C_SDA, I2C_SCK
TMDS CLOCK±
A5 – A8,
B5 – B8
IC2601
HM_HD, HM_VD
C7, C6
Y12 – Y15,
AA12 – AA15
Y16 – Y19,
AA16 – AA19
B17, A17, D18, B18,
A18, B19, A20, B21
40 40
39 39
71 71
HM_B0 – HM_B7
C2
J21
XCS_IC_2601
XHDMI_RST
T26
A28
42 42
41 41
9 9
DE_HDMI
J12
TMDS DATA0± –
TMDS DATA2±
F2, F1
XBB_RST
G20
HMCK
HM74CK
HM_FLD
T20
P21
R21
D0_HDMI-D23_HDMI
F9, F10
BB_SI, BB_SO, XBB_SCK
H2
HM_HD, HM_VD
HM_R0 – HM_R7
10
OVERALL (5/7)
(PAGE 3-5)
FP-907 FLEXIBLE
BOARD
CN1106
G9, G10
XCS_IC_2401
E21
F20
HM_Y0 – HM_Y7
D3, D2, F2
L18, M19, M18
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL, U27
MODE CONTROL
(4/12 – 6/12)
D12
72, 73 54, 56, 58, 60, 62, 64, 66, 68 43 –50 53, 55, 57, 59, 61, 63, 65, 67
72, 73 54, 56, 58, 60, 62, 64, 66, 68 43 –50 53, 55, 57, 59, 61, 63, 65, 67
DR_VINCK
DR_SCK54
F35
E35
33, 31, 35
33, 31, 35
G35
HM_B0 – HM_B7
10, 8 14, 16, 18, 20, 22, 24, 26, 28 31 –38 13, 15, 17, 19, 21, 23, 25, 27
10, 8 14, 16, 18, 20, 22, 24, 26, 28 31 –38 13, 15, 17, 19, 21, 23, 25, 27
DR_GSPILOT
47, 49, 45
47, 49, 45
IC1701
(2/5)
DR_GSDATA0 – DR_GSDATA3
B15
HM_R0 – HM_R7
T21, U20
G32, G34,
F32, F34
H35
HM_Y0 – HM_Y7
U21, V20,
V21, W20,
W21, Y20,
Y21, AA20
DR_GHPILOT
B16, A16,
A15, A14
DR_GHDATA0 – DR_GHDATA3
D14, B14,
D13, A13
DR_VDATA0 – DR_VDATA7
J1, G2, H1
E32, G33,
E33, F33
D35, E34, D33, D34,
D32, C34, B33, C33
BB_SI, BB_SO, XBB_SCK
8, 9, 5, 6, 2, 3
IC_2401_Y_OUT
IC_2401_C/PB_OUT
IC_2401_PR_OUT
8
SDA, SCL
CEC
16, 15
AA9
AA11
Y10
11, 12
VC-522 BOARD (3/6)
27, 29, 28
3-3. OVERALL BLOCK DIAGRAM (3/7)
14
Q2704
K3
12
OVERALL (4/7)
(PAGE 3-4)
05
HDR-TG1/TG1E/TG3E_L2
3-3
HDMI_JACK_IN
LEVEL
SHIFT
2
HPD
19
3-4. OVERALL BLOCK DIAGRAM (4/7)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
OVERALL (3/7)
(PAGE 3-3)
35
33
31
CN9022
(2/3)
CN9101
(2/3)
13 13
15 15
17 17
CN1101
(2/3)
Y_TO_Y
37 37
C_TO_PB
35 35
V_TO_PR
33 33
CN1111
CN003
S_Y/D3_Y
38 38
S_C/D3_Pb
40 40
VIDEO/D3_Pr
42 42
IC2501
BB_SO, XBB_SCK
23, 22
7
2
4
6
Y_TO_Y
C_TO_PB
V_TO_PR
FP-908 FLEXIBLE BOARD
AUDIO_L_I/O
AUDIO_R_I/O
COMPONENT
OUT AMP,
D-TERMINAL
DRIVE
(11/12)
USB_D±
34 34
32 32
S_Y_I/O
S_C_I/O
VIDEO_I/O
AUDIO_L
AUDIO_R
USB_D±
16
12
8
20
22
34, 36
CN1036
(2/3)
IC_2401_Y_OUT
IC_2401_C/PB_OUT
IC_2401_PR_OUT
MD-137 BOARD (2/3)
28, 26
28, 26
FP-902 FLEXIBLE
BOARD (2/3)
VC-522 BOARD (4/6)
Q1103
20
USB_VCC
USB_VBUS
13
OVERALL (7/7)
(PAGE 3-7)
49 49
45 45
47 47
1 1
5 5
3 3
ADA_FCK
ADA_BCK
ADA_LRCK
ADA_FCK
ADA_BCK
ADA_LRCK
FP-903 FLEXIBLE
BOARD (2/3)
ADA_SOA0
ADA_SOA1
XCS_IC_2801
SYS_SOUND
SP±
78, 76
78, 76
CN1102
(2/3)
59 59
21 21
61 61
63 63
19 19
17 17
65 65
80 80
15 15
2 2
4, 6
4, 6
U26
R35
ADA_SIA0
CN9102
(2/3)
78, 76
78, 76
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL, R29
MODE CONTROL
(4/12 – 6/12)
N28
P29
USB_D±
CN9034
(2/3)
3, 5
3, 5
CN1037
(2/3)
W35, V35
IC1701
(3/5)
ADA_FCK
ADA_BCK
ADA_LRCK
11
9
ADA_SIA0
OVERALL (3/7)
(PAGE 3-3)
OVERALL (3/7)
(PAGE 3-3)
IC_2401_Y_OUT
IC_2401_C/PB_OUT
BB_SO, XBB_SCK
ACV_UNREG_CN
G25
H28
AJ34
CN1035
(1/3)
XVBUS_DET
LANC_SIG
Y_TO_Y
K1
C_TO_PB
M2
V_TO_PR
L1
N4
N3
S_Y/D3_Y
S_C/D3_Pb
VIDEO/D3_Pr
HDMI_JACK_IN
JACK_AD
31
16
24
10
30
MIC901
MICROPHONE
UNIT
2
FRONT
4
L
6
R
ADA_SIA0
ADA_SIA0
ADA_SOA0
ADA_SOA1
ADA_SOA0
ADA_SOA1
XCS_IC_2801
SYS_SOUND
XCS_IC_2801
SYS_SOUND
SP±
SP±
P12
N13
P13
J14
A4
AUDIO_L_I/O
AUDIO_R_I/O
F2
G1
MULTI_JACK_IN
1, 2
1, 2
CN002
SP(+), SP(-)
35 35
37 37
33 33
29 29
PON (DVD BURN)
MULTI_JACK_IN
BATT/XEXT_CR
ACV_UNREG
LANC_SIG
S_Y/D3_Y
S_C/D3_Pb
VIDEO/D3_Pr
4 4
6 6
8 8
30
37
26
35
31
10
5
9
CN4006
CN4005
(1/3)
(1/3)
XVBUS_DET
HDMI_JACK_IN
JACK_AD
CN4003
INT_MIC_F
INT_MIC_L
INT_MIC_R
14
18
22
24
16
1
39
2
AUDIO_L
AUDIO_R
MULTI_JACK_IN
9 9
CN001
A/V R
1
6
7
LANC_SIG
VIDEO/AUDIO I/O
(3/7)
11 11
14
LANC_SIG
2
SE001
PANEL_O/C_NOR_CN
PANEL_O/C_REV_CN
3 3
1 1
PNAEL
2
OPEN/CLOSE
3
DETECT
XSYS_RST
26
3
14 14
12 12
IC2801
FP-916 FLEXIBLE
BOARD (1/3)
37
38
CN1110
(2/4)
XVBUS_DET
HDMI_JACK_IN
JACK_AD
K14
XSYS_RST
12
OVERALL (3/7)
(PAGE 3-3)
INT_MIC_F
A10
INT_MIC_L
B14
INT_MIC_R
B13
FP-904 FLEXIBLE
BOARD (1/2)
CN1027
(1/2)
SP±
27 27
USB_D±
MS-396 BOARD
(1/3)
9
ACV_UNREG
N14
M14
M13
OVERALL (7/7)
(PAGE 3-7)
FP-913 FLEXIBLE
BOARD (1/3)
(DVD BURN)
MULTI_JACK_IN
BATT/XEXT
SP901
SPEAKER
05
HDR-TG1/TG1E/TG3E_L2
3-4
CN002
INTERFACE
CONNECTOR
for
Handycam station
K13, J13
ADA_FCK
ADA_BCK
ADA_LRCK
B1, C2
M29
M28
N29
KEY_AD1
JACK_AD_CRADLE
BATT/XEXT_CR
USB_DET/VBUS
1–4
XCS_DDRA
USB
DETECT
41, 43 – 50
41, 43 – 50
T25
XBUS_DET
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
EMC_ADDR[0] –
EMC_ADDR[15]
EMC_CLK1_OUT
Y25
EMC_CLK1_IN
Y26
T4
P11
B29
B28
EMC_XRESET_OUT
XCS_LCD
34
47
PANEL_RGT,
PANEL_DWN,
PANEL_XSTBY
RGT, DWN, XSTBY
34, 20
TP_X
TP_Y
26
23
TP_SEL1
24
Q1701
TP_SEL2
TP_X
TP_Y
TP_SEL1
TP_TOP
TP_L
14
17
TOUCH
PANEL
I/F
16
TOUCH PANEL
SELECT SWITCH
TP_R
TP_BOT
TP_R
TP_BOT
4
2
AF16
BACKLIGHT
DRIVE
7
MSX_BIO0 – MSX_BIO3
MSX_BS
MSX_CLK
34
30
XMS_ACC_LED
26
MSX_BIO0 – MSX_BIO3
MSX_BS
MSX_CLK
D4002
(MS ACCESS)
33
BL_H
BL_L
D901
(BACKLIGHT)
5, 7, 4, 8
XMS_ACC_LED
35, 33, 36, 32
AM30, AN33,
AN30, AM32
AM31
AR32
TOUCH
PANEL
CN001
BL_H
BL_-V
H23
1
4
Q6001, Q6002
15
OVERALL (6/7)
(PAGE 3-6)
CN003
TP_TOP
5
TP_L
2
1
3
Q6018 – Q6020
EXTDA, BL_ON
XFLASH_RST
RGT, DWN, XSTBY
2.7 inch
WIDE
COLOR
LCD
UNIT
MSDATA0 – MSDATA3
MSBS
MS_SCLK
6
10
4, 3, 5, 7
NAND
XCS_LCD
PSIG, HCK1, HCK2,
REF, HST, PCG,
EN, VCK, VST
5, 6
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
MODE CONTROL
EMC_ADDR[0] –
(4/12 – 6/12)
EMC_ADDR[15]
AM35
AN34
EMC_DATA[0] –
EMC_DATA[15]
6
6, 12, 11
K11
XCS_LCD
IC1701
(4/5)
PANEL_VP,
PANEL_HCK1, PANEL_HCK2,
PANEL_REF, PANEL_HST,
PSIG, HCK1, HCK2,
PANEL_PCG, PANEL_EN,
REF, HST, PCG,
PANEL_VCK, PANEL_VST
EN, VCK, VST
COM, CS
1, 2
T27
EMC_CLK0_OUT
W25
EMC_CLK0_IN
W26
LCD DRIVE
(1/2)
LCD901
CN002
R
4
G
5
B
3
2, 19, 14 6 – 8, 11 – 13, 20 – 22 1, 24, 23
BB_SI, BB_SO,
XBB_SCK
PANEL_COM
29
IC6001
FP-909 FLEXIBLE
BOARD
25, 6, 5
PANEL_HD,
PANEL_VD
37
36
35
CN6007
R
22
G
21
B
23
COM,
COM/CS, N.C.
20 – 15, 9 – 7
PANEL_HD, PANEL_VD
EMC_ADDR[0] –
EMC_ADDR[12],
EMC_ADDR[14],
EMC_ADDR[15]
SDRAM
E8
PANEL_HD,
PANEL_VD
PANEL_R
PANEL_G
PANEL_B
39
37
38
PANEL_VR
22
PANEL_VG
23
PANEL_VB
24
24, 10, 14
EMC_DATA[0] –
EMC_DATA[31]
PANEL_R
PANEL_G
PANEL_B
CN4005
(2/3)
26, 7, 8, 31, 9,
10, 13, 16, 18
EMC_DATA[0] –
EMC_DATA[31]
21, 20
(7/12)
OVERALL (3/7)
(PAGE 3-3)
1
3
2
MS-396 BOARD (2/3)
52, 2
PANEL_R
PANEL_G
PANEL_B
8
IC2101
FP-913 FLEXIBLE
BOARD (2/3)
CN1035
(2/3)
46, 49, 48
VC-522 BOARD (5/6)
19, 20
3-5. OVERALL BLOCK DIAGRAM (5/7)
2
8
05
CN4004
FP-916 FLEXIBLE
BOARD (2/3)
BB_SI, BB_SO, XBB_SCK
BL_CONT
16
XMS_IN
OVERALL (7/7)
(PAGE 3-7)
XPOWER_SW
CN4006
(2/3)
13, 11, 12
10
OVERALL (3/7)
(PAGE 3-3)
MEMORY
STICK
DUO
BL_CONT
8
XMS_IN
28
S4001
POWER
33
HDR-TG1/TG1E/TG3E_L2
3-5
6
A : VIDEO SIGNAL
A : VIDEO/AUDIO SIGNAL
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-912 FLEXIBLE
BOARD
STRB_CHARGE
XSTRB_FULL
STROB_ON
4
5
6
T5001
ST_UNREG
2
CN7504
XE_A
D5003
6
FLASH UNIT (FL27500)
1
4
3
2
1
TRIGGER
5
3
XSYS_RST
SCHARGE_ON
XSCHARGE_FULL
STROBO_ON
2
1
8
7
4
XE_K
IC5001
FLASH/
CHARGE
CONTROL
6
Q5001
FLASH
DRIVE
CN7505
XE_A
1–3
5
OVERALL (2/7)
(PAGE 3-2)
CN7501
CN1026
STRB_CHARGE
XSTRB_FULL
STROBE_ON
ST-186 BOARD
10 – 12
VC-522 BOARD (6/6)
FP-914 FLEXIBLE BOARD
6–8
3-6. OVERALL BLOCK DIAGRAM (6/7)
C001
+
CHARGING
CAPACITOR
FP-903 FLEXIBLE
BOARD (3/3)
V2
XMODE_SW
46 46
FR_SI, FR_SO,
XFR_SCK, XCS_EX
55, 57,53, 67
55, 57,53, 67
B22, C22, A22, D22
L19
STABLE_RUN
48 48
3
CN9034
CN9102
(3/3)
(3/3)
XMODE_SW
FR_SI, FR_SO,
XFR_SCK, XCS_EX
36
25, 23, 27, 13
CN1037
(3/3)
STABLE_RUN
34
17
OVERALL (7/7)
(PAGE 3-7)
XFLASH_RESET
OVERALL (1/7)
(PAGE 3-1)
15
XFLASH_RESET
OVERALL (5/7)
(PAGE 3-5)
G2
XEX_RST
54 54
52 52
XFLASH_RESET
28
XEX_RST
30
FP-905 FLEXIBLE BOARD
IC001
PANEL
REVERSE
DETECT
5
4
FP-904 FLEXIBLE BOARD (2/2)
S002
DISP/
BATT INFO
XBATT_VIEW
S001
RESET
FR_XRESET
CN1030
PANEL_NOR/REV
IC1701
(5/5)
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
MODE CONTROL AK3
(4/12 – 6/12)
AJ33
H26
AH34
CN1027
(2/2)
CN1035
(3/3)
XPHOTO_LED
ZOOM_VR_AD
START/STOP
KEY_AD1
CN4005
(3/3)
XPHOTO_LED
ZOOM_VR_AD
START/STOP
KEY_AD1
14
25
15
27
5
XBATT_VIEW
8
G23
C23
4
MS-396 BOARD
(3/3)
FP-913 FLEXIBLE
BOARD (3/3)
H25
WD_DIS
WD_DIS
XHOT_STBY
17
11
XHOT_STBY
FP-916 FLEXIBLE
BOARD (3/3)
CN4006
(3/3)
26
15
25
13
20
25
19
17
32
27
23
29
16
27
22
28
21
23
XPHOTO_LED
ZOOM_VR_AD
START/STOP
KEY_AD1
XBATT_VIEW
WD_DIS
XHOT_STBY
Q1002
S008
EASY
CONTROL SWITCH BLOCK
(PH27500)
PHOTO
KEY_AD0 (EASY)
G24
K27
CN001
S001
(PHOTO FREEZE)
3
S002
(PHOTO REC)
5
KEY_AD0 (PHOTO_FREEZE)
KEY_AD0 (PHOTO_REC)
PANEL_O/C_NORMAL
13
PANEL_O/C_NOR_CN
PANEL_O/C_REVERSE
12
PANEL_O/C_REV_CN
Q1001
7
6
KEY_AD0
FP-902 FLEXIBLE
BOARD (3/3)
AH35
CN1036
(3/3)
SE-174 BOARD (2/2)
BT6601
LITHIUM
BATTERY
CN6601
(2/2)
BATT_LI_3V
AN6
FP-911 FLEXIBLE
BOARD (2/2)
1
PANEL_O/C_NOR_CN
8
11
CN1029
(2/2)
BATT_LI_3V
XQUICKREC_LED
46 46
18 18
XBATT_VIEW
FR_XRESET
20 20
27 27
05
HDR-TG1/TG1E/TG3E_L2
3-6
CN9022
CN9101
(3/3)
(3/3)
XQUICKREC_LED
XSYS_RST
FR_XRESET
BATT_LI_3V
6
34
32
23
19
OVERALL (7/7)
(PAGE 3-7)
PANEL_O/C_REV_CN
18
OVERALL (7/7)
(PAGE 3-7)
XENON
LAMP
3-7. OVERALL BLOCK DIAGRAM (7/7)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
MD-137 BOARD (3/3)
34
28
30
FR_SI, FR_SO,
XFR_SCK, XCS_EX
STABLE_RUN
XFLASH_RESET
XEX_RST
CN1110
(3/4)
XPHOTO_LED
20
ZOOM_VR_AD
15
START/STOP
21
KEY_AD1
23
XQUICKREC_LED
XPHOTO_LED
ZOOM_VR_AD
START/STOP
KEY_AD1
G11
L3
X4901
32.768kHz
XPHOTO_LED
OVERALL (6/7)
(PAGE 3-6)
STABLE_RUN
13
24
17
XBATT_VIEW
XBATT_VIEW
WD_DIS
WD_DIS
XHOT_STBY
XHOT_STBY
XFLASH_RST
XSYS_RST
18
19
PANEL_O/C_NOR_CN
PANEL_O/C_REV_CN
1
IC1103
3
AND GATE
(7/7)
ZOOM_VR_AD
START/STOP
B2
D9
E10
XMODE_SW
A8
HI CONTROL
(4/7)
19
34
OVERALL (6/7)
(PAGE 3-6)
32
23
XSYS_RST
FR_XRESET
BATT_LI_3V
R1
R2
M2
VTR_DD_ON
FR_XRESET
BATT_IN
VOUT
D4702
14
PANEL_O/C_NOR_CN
IC4701
OVERALL (4/7)
(PAGE 3-4)
PANEL_O/C_REV_CN
DC CONTROL,
RESET,
LANC DRIVE
(6/7)
LANC_SIG
K3
ACV_UNREG_CN
J3
J2
M3
L3
D14
FR_EVER_SO,
FR_EVER_SCK,
XCS_DD
LANC_IN
LANC_OUT
XLANC_ON
XLANC_PWR_ON
BATT/XEXT_CN
13
7
8
5
10
4
11
9
4
12
1
8
7
XCHARGE_LED
D001
FLASH/CHG
XPHOTO_LED
D002
STILL
XCAM_LED
D003
MOVIE
D004
XQUICK_LED
QUICK ON
ZOOM_VR
T
RV001
(ZOOM)
START/STOP
S004
START/STOP
XMODE_SW
S001
STILL/MOVIE
SELECT
13
OVERALL (4/7)
(PAGE 3-4)
BATT/XEXT
ST_UNREG,
VTR_UNREG,
VTR2_UNREG,
MT_BL_UNREG
F2
K2
A7
E11
D2, D1, G1 B11, J2, K10, L10
6
KEY_AD1
JACK_AD_CRADLE
BATT/XEXT_CR
JACK_AD_CRADLE
BATT/XEXT_CR
B4
C7
M13, L13, K13
XSYS_RST
2
CN1108
N7
N5
P3
N2
CN1101
(3/3)
XQUICKREC_LED
CN1116
IC4901
B8
FR_XRESET
BATT_LI_3V
CONTROL SWITCH BLOCK (PS27500)
FP-906 FLEXIBLE
BOARD
E9
Q1104
XPANEL_POWER_ON
XCAM_LED
XQUICK_LED
J11
B1
4
XCAM_LED
J4, L5, K5, H3
FR_SI, FR_SO, XFR_SCK, XCS_EX
XCHARGE_LED
L2
F11
18
CN1109
XCHARGE_LED
F10
FAST_CHARGE
ACV_UNREG_CN
AVC_GND
BATT_UNREG_CN
B3
B6
XPOWER_SW
XMS_IN
BL_CONT
A_1.2V, D_1.2V, IC_1301_D_1.2V, IC_2201_D_1.2V
D_1.5V
A_2.8V, AU_2.8V, D_2.8V, EP_2.8V, CMOS_D_2.8V
A_4.6V, AU_4.6V, EP_4.6V
D_1.8V, A1.8V
D_3.3V, CMOS_A_3.3V, USB_3.3V
MT_5.0V
EP_8.5V
BL_-V
EVER_3.0V
LANC_DC
05
HDR-TG1/TG1E/TG3E_L2
3-7
1
FP-917 FLEXIBLE
BOARD
CN1105
BATT_UNREG
BATT_SIG
BATT_GND
B10
C10
H2
C1
J901
DC IN
2
Q4603,
Q4604
D4602
A4
3
Q4601,
Q4602
INIT_CHARGE_ON
BATT_SIG
ACV_UNREG
9 – 14
17
OVERALL (6/7)
(PAGE 3-6)
XMODE_SW
+
7
C
1–6
25, 23, 27, 13
36
CN1102
(3/3)
XMODE_SW
−
CN1110
(4/4)
XPOWER_SW
7
XMS_IN
12
16
BL_CONT
OVERALL (5/7)
(PAGE 3-5)
32
BH001
BATTERY
TERMINAL
W
3-8. POWER BLOCK DIAGRAM (1/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
MD-137 BOARD (1/3)
3
FP-917 FLEXIBLE
BOARD
9 – 14
C
7
−
Q4603,
Q4604
BATT/XEXT
ST_UNREG
IC4601
RESET
(5/7)
Q4714 CLAMP
F4604
BATT_UNREG
F4602
VTR2_UNREG
BATT_SIG
BATT_GND
BATT/XEXT_CR
XPOWER_SW
FP-906 FLEXIBLE
BOARD
D003
MOVIE
W
3
6
9
R4930
P30_AN00 J5
P32_AN02 K6
14
D004
QUICK ON
12
S001
STILL/MOVIE
SELECT
VCC1
VCC2
AVCC
AVR
BATT_UNREG
EVER_3.0V
1
3
CHARGE_LED_VDD
R1130
R4932
HI CONTROL
(4/7)
B2 vin
LX4a R12
LX4b P12
IN4 N11
R4718
P1
R5
L1
P15
B_UNREG
VRO
CH9_SW1
CH6_SW
LX6a R9
LX6b P9
IN6 N10
R4901
VOUT
F4601 MT_BL_UNREG
BATT_IN
P70_INT00 A7
CLAMP
Q4709
B+ SWITCH
CLAMP
7
8
FR_EVER_SO
FR_EVER_SCK
XCS_DD
P11_SO1 D2
P12_SCK1 D1
P21_PPG01 G1
LX7a G1
LX7b G2
IN7 F3
LX8a A6
LX8b B6
IN8 C7
A10 PVDD5a
B10 PVDD5b
LX5a A9
LX5b B9
IN5 C8
R4715
L4708
IC_1301_D_1.2V
L4726
XLANC_ON
XLANC_PWR_ON
P23 H2
P07_INT11 C1
FR_XRESET
VTR_DD_ON
LANC_DC
1.8/3VCTRL
P64
P65
B8 A8
XSYS_RST
SD1
C
XSYS_RST
FR_XRESET
1
POWER
ON/OFF
Q4701
VR
Q4706
L4732
SWITCHING
BL_-V
R4728
BL_CONT
Q4702, 4703
BACKLIGHT
CONTROL
SD1 N9
DC CONTROL,
RESET, LANC DRIVE
(6/7)
XFLASH_RST
POWER (2/3)
(PAGE 3-9)
MT_5.0V
D4702
XMODE_SW
POWER (3/3)
(PAGE 3-10)
3
IC4703 DC CONTROL
(6/7)
OUT10-1 C15
+INE10 C14
-INE10 D14
P3 RST_OUT(RESET)
N5 CTL1
N7 CH8_SELECT
IC4701
B
DVDD1 A1
PVDD11 A2
OUT11 R15
B13
MT_BL_UNREG
P61_PPG11 C11
RSTX K2
P20_PPG00 F2
–
+
4
-INE9 C12
VR P4
M3 XCTL2
L3 WAKE_UP
R4796
R4717
D4707
K1 SENSEa
K2 SENSEb
L2 LANC_DC(5.6V)
D
L4705
D15 DVDD3
A_1.8V
D_1.8V
R4732
L4733
D4709 D4708
M13 DIN
L13 CLK
K13 LD
L4731
D_3.3V
CMOS_A_3.3V
USB_3.3V
VB B1
XMODE_SW
A_4.6V
AU_4.6V
EP_4.6V
Q4715
A5 PVDD8a
B5 PVDD8b
N2 CS_OUT
R4791 D_1.5V
L4724
L4721
L4715
R4731
V_UNREG
AVDD1
AVDD3
DVDD4
A12 DVDD2
M2 VOUT
Q4711
Q4708
B+ SWITCH
vout B1
R4716
L4707
R1153
QUICK_LED_VDD
N1
P2
C10
N12
F1 PVDD7a
F2 PVDD7b
B11
J2
L10
K10
IC4901
D001
FLASH/CHG
R10 PVDD6a
P10 PVDD6b
B3 P02_INT06
D002
STILL
D_2.8V
A_2.8V
AU_2.8V
L4706
R4934
R1129
MODE_LED_VDD
EP_2.8V
L4713
L4725
L4723
PVDD10 A3
PVDD12 A4
D_1.2V
R4931
10
L4714
Q4707
B+ SWITCH
L4704
EVER_3.0V
T
RV001
(ZOOM)
A_1.2V
D_1.2V
IC_2201_D_1.2V
R4720
VTR_UNREG
P31_AN01 L6
P33_AN03 J7
CN1116
R4723
R4711
R4713
IC4708 1.5V REG
(6/7)
R11 PVDD4a
P11 PVDD4b
CLAMP_ON
P34_AN04 L7
CN1109
D_2.8V
LX3a K15
LX3b K14
IN3 J13
XUNREG_RESET
P06_INT10 C2
P22 G2
EVER_3.0V
LANC_DC
L4722
L4703
J15 PVDD3a
J14 PVDD3b
R4935
C7 P71_INT01
A4 SIO2
B1 P05_INT09
L4701
IN2 E3
F10 E11
P52
P53
BATT_SIG
BATT/XEXT_CN
POWER (3/3)
(PAGE 3-10)
LX1a G15
LX1b G14
IN1 H13
F4603
D_2.8V
A
H15 PVDD1a
H14 PVDD1b
E1 PVDD2a
E2 PVDD2b
ACV_UNREG_CN
CONTORL SWITCH
BLOCK (PS27500)
ST_UNREG
1 OUT VDD 2
Q4601,
Q4602
D4602
CN1105
1–6
BH001
BATTERY
TERMINAL
+
F4605
ACV_UNREG_CN
1.8/3V__GATE_CTRL
1
R1143
ACV_GND
VTR_UNREG
2
INIT_CHARGE_ON
FAST_CHARGE
J901
DC IN
CN1108
ACV_UNREG
05
HDR-TG1/TG1E/TG3E_L2
3-8
VCH
VBATT
VREF (2.5V)
VOUT3
R2
R1
P5
B2
R4708
BATT_LI_3V
EP_8.5V
POWER (3/3)
(PAGE 3-10)
3-9. POWER BLOCK DIAGRAM (2/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-522 BOARD (1/2)
CN1101
CN9101
30 30
CN9022
A_1.8V
D_1.8V/CMOS_D_2.8V
STRB_CHARGE
XSTRB_FULL
STROBE_ON
A_1.8V
AC11 GPIO0_10
AJ5 GPIO0_5
AE20 STRB0
I/O_1.8V
L1301
CN1036
22 22
I/O_1.8V
COMS_A_3.3V
R1307
CN6902
41, 43 45, 47
I/O_1.8V
FP-902 FLEXIBLE
BOARD
A_1.8V
CM-096 BOARD
CN1303
46, 48
MD-137 BOARD (2/3)
CLOCK
GENERATOR
(1/12)
41, 43 45, 47
POWER (3/3)
(PAGE 3-10)
IC1303
L1302
46, 48
F
A_1.8V
CN1026
STRB_CHARGE
4
XSTRB_FULL
5
STROB_ON
6
3
3
R6905, R6954 LVDS_I/O_1.8V
I/O_1.8V
D_1.8V/CMOS_D_2.8V R6902, R6953
COMS_A_3.3V
IC6903
4
R6952
3
D_1.8V
R6947
R6948
R6949
R6950
R6951
A_2.7V
R6937
R6938
R6939
R6940
R6941
R6942
R6943
R6944
R6946
2.7V REG
R1308
A_2.8V
IC_1301_D_1.2V
D_2.8V
D_3.3V
12, 14 16, 18, 20, 22, 24
12, 14 16, 18, 20, 22, 24
28 28
IC_1301_D_1.2V
D_2.8V
D_3.3V
IC1301
D_2.8V
D_3.3V
29 29
G
POWER (3/3)
(PAGE 3-10)
XSYS_RST
XSYS_RST
34 34
A_2.8V_AR
L1502
IC_1301_D_1.2V
A_1.2V
21 21
A_2.8V
24 24
38, 40 28, 30, 32, 34, 36
38, 40 28, 30, 32, 34, 36
A_2.8V
FB1501
D_2.8V_AR
R1507
D_2.8V_PLL
R1502
D_3.3V_AR
L1501
A_1.2V_AR
CAMERA SIGNAL PROCESSOR,
CAMERA CONTROL
(1/12, 2/12)
J
XFLASH_RST
XCLR
POWER (3/3)
(PAGE 3-10)
D_1.8V_AR
R1503
R1504 D_1.8V_DDR1
R1505 D_1.8V_DDR2
XRESET_REQ
PCI_XRESET
AE1 XRESET_REQ
N5 PCI_XRESET
18 18
AC5 XRESET
CN1033
XRST_IC_5201
GPIO0_8 AF5
GPIO0_14 AF4
GPIO0_4 AB9
FP-910
FLEXIBLE
BOARD
K2 XCLR
LD-235 BOARD
16
24
XCLR
CN5201
XRST_IC_5201
FR_XRESET
27 27
CMOS_A_3.3V
FR_XRESET
32 32
CMOS_A_3.3V
23 23
CMOS_A_3.3V
11, 12 38, 39
CMOS_A_3.3V
D_2.8V
MT_5.0V
1, 2
D_2.8V
MT_5.0V
1, 2
MT_5.0V
POWER (1/3)
(PAGE 3-8)
CMOS_A_3.3V
FB5201
D_2.8V
BATT_LI_3V
23 23
A_4.6V
25 25
USB_3.3V
E4
E3
D2
C1
21 21
A_1.2V
D_1.8V
CN9102
(1/2)
7 7
CN9034
(1/2)
A_1.2V
D_1.8V
A_1.2V
A_2.8V
D_1.2V
D_1.8V
D_2.8V
D_3.3V
USB_3.3V
A_2.8V
R2503
R2502
VR
CN1037
(1/2)
A_1.8V
R2218
R2219
D_2.8V
D_3.3V
R2237
IC2201
R2238
IC_2201_D_1.2V
R2239
AUDIO/VIDEO
CODEC
(8/12)
D_1.8V
R2235
64, 66, 68, 70
64, 66, 68, 70
IC_2201_D_1.2V
BATT_LI_3V
H
A_2.8V
A_4.6V
D_2.8V
D4_-2.8V
L2502
L2501
R2501
SE-174 BOARD
6
6
9
3
11
1
CN6601
VST_C_RST
A_2.8V
L6601
L2503
D_1.8V
IC2301
A_2.8V
512M SDRAM
(9/12)
D_1.8V
IC1601
256M SDRAM
(3/12)
FP-904 FLEXIBLE BOARD
CN1027
(2/2)
4
D4_-2.8V
05
HDR-TG1/TG1E/TG3E_L2
3-9
FR_XRESET
S001
RESET
IC1702
BUFFER
(4/12)
A_2.8V
BATT_LI_3V
IC2501
COMPONET
OUT AMP,
D-TERMINAL
DRIVE
(11/12)
R1701
D_2.8V
IC_2201_D_1.2V
ZM_RST_LED
SE6602
5 HSC
PITCH/YAW
SENSOR
H1 IHRSTX
R2236
POWER (3/3)
(PAGE 3-10)
6
FP-911
FLEXIBLE
BOARD
CN1011
D2.8V
4
73 73
69, 71
69, 71
CN1102
(1/2)
D4_-2.8V
PVDD
VOUT A3
SVDD
FB B2
IC2502
S1
S2 -2.8V REG
(11/12)
16 16
FP-903 FLEXIBLE
BOARD (1/2)
9, 11
9, 11
POWER (3/3)
(PAGE 3-10)
VR
36 36
12, 14, 16, 18
12, 14, 16, 18
E
USB_3.3V
29 29
VR
A_1.2V
D_1.2V
IC_2201_D_1.2V
D_2.8V
A_2.8V
A_4.6V
A_1.8V
D_1.8V
D_3.3V
CMOS_A_3.3V
USB_3.3V
IC_1301_D_1.2V
MT_5.0V
VR
BATT_LI_3V
D_1.2V
CN1029
VST_C_RST
C2
STBY
31, 33, 35, 37
31, 33, 35, 37
13, 15, 17, 19
13, 15, 17, 19
L2504
D_1.2V
34
A_4.6V
25 25
B1
CN5202
MR_A2.8V
3
ZM_VCC
27
SENSOR
SWITCH
BATT_LI_3V
27 27
IC5205
Q5201
ZM_RST_LED
A_4.6V
B2
IC5201
FOCUS/ZOOM
/LENS COVER
MOTOR DRIVE,
ND FILTER
DRIVE,
IRIS DRIVE
2.8V REG
A_2.8V
BATT_LI_3V
R5263
FR_XRESET
20 20
IC5204
FOCUS MOTOR
NOISE FILTER
R5202
38, 39 28, 29
2, 4, 6
2, 4, 6
46, 48, 50
46, 48, 50
C
MT_5.0V
H11 XCLR
TG1E/TG3E
D_1.8V
MT_5.0V
IC6904
4M CMOS
IMAGER
LENS
BARRIER
UNIT
IC1705
FP-905 FLEXIBLE BOARD
BUFFER
(4/12)
CN1030
D2.8V
IC001
6
PANEL
REVERSE
DETECT
BT6601
LITHIUM
BATTERY
LENS
BLOCK
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
L2403
D_1.2V
R2446
D_2.8V
R2445
ST_UNREG
DOWN
CONVERTER
(10/12)
XRST J21
XBB_RST
MT_5.0V
L1101
1–3
A_2.8V
FP-915 FLEXIBLE
BOARD
CN1112
IC2401
ST_UNREG
4, 5
L2401
MT_5.0V
FLASH UNIT
(FL27500)
ST-186 BOARD
CN7504
CN7503
T5001
L5001
1 VBAT
3 VCC
R5005, 7501
D5003
10 – 12
MD-137 BOARD (3/3)
A_1.2V
1–3
VC-522 BOARD (2/2)
4, 5
3-10. POWER BLOCK DIAGRAM (3/3)
XE_A
SW 2
XENON
LAMP
IC5001
SD1
XSYS_RST
XMODE_SW
FP-903 FLEXIBLE
BOARD (2/2)
H
D_1.8V
POWER (2/3)
(PAGE 3-9)
D_2.8V
D_1.8V_DDR
R2013
R2014
D_1.8V_EMC
D_3.3V
FB2001
D_2.8V_PERI
FB2002
D_2.8V_VIDEO
R2007
52 52
SIO2_SCS L19
46 46
XEX_RST
XMODE_SW
5 5
R4954
D_1.5V
FL2603
30 30
36 36
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
MODE CONTROL
(4/12 – 6/12)
R2105
HDMI
TRANSMITTER
(2/7)
L2803
L2805
L2804
L2801
77 77
3 3
AU_2.8V
MT_5.0V
F_/RP E8
EP_2.8V
EP_4.6V
54 54
J
39
6
XFLASH_RST
D
POWER (1/3)
(PAGE 3-8)
E
POWER (2/3)
(PAGE 3-9)
ST_UNREG
A_1.2V
D_1.2V
IC_2201_D_1.2V
EP_2.8V
D_2.8V
A_2.8V
AU_2.8V
D_1.5V
A_4.6V
AU_4.6V
EP_4.6V
A_1.8V
D_1.8V
D_3.3V
CMOS_A_3.3V
USB_3.3V
IC_1301_D_1.2V
MT_5.0V
VR
BL_-V
BL_CONT
BATT_LI_3V
EP_8.5V
A_1.2V
D_1.2V
IC_2201_D_1.2V
D_2.8V
A_2.8V
A_4.6V
A_1.8V
D_1.8V
D_3.3V
CMOS_A_3.3V
USB_3.3V
IC_1301_D_1.2V
MT_5.0V
VR
BATT_LI_3V
VSS
IC6001
LCD DRIVE
(1/2)
MS_PWR_ON
BL_CONT
1
CE
R1152
MS_VCC
4 VDD VOUT 3
IC1104
D_2.8V
VGND
BACKLIGHT
DRIVE
32
33
8
7
BL_-V
7
MS_VCC
CN1111
LANC_DC
D_2.8V
34
XPOWER_SW
Q6101, Q6102
TOUCH
PANEL I/F
D4002
(MS ACCESS)
S4001
POWER
33
CN001
A/V R
CN003
LANC_DC
7 7
4
POWER (1/3)
(PAGE 3-8)
LANC_DC
BATT/XEXT_CR
LANC_DC
BATT/XEXT
ACV_UNREG_CN
EVER_3.0V
ACV_UNREG
EVER_3.0V
31 31
33 33
5 5
LANC_DC
BATT/XEXT_CR
ACV_UNREG
SE001
PNAEL
OPEN/CLOSE
DETECT
33
35
CN002
INTERFACE
CONNECTOR
for
Handycam station
IC1103
AND GATE
(7/7)
FP-907
FLEXIBLE
BOARD
IC2703
5V REG
(2/7)
ST_UNREG
5 VIN VOUT 4
CONT
1
D_2.8V
05
HDR-TG1/TG1E/TG3E_L2
3-10E
CN1106
+5V POWER
+5V POWER
BL_L
17
2.7 inch
WIDE COLOR
LCD UNIT
WITH TOUCH
PANEL
13
VSSG
15
18
26
27
BL_H
BL_L
D901
(BACKLIGHT)
VCC
FP-908 FLEXIBLE
BOARD
A
VSS
BL_-V
R4008
XPOWER_SW
BL_H
Q6018 – Q6020
BL_CONT
6
2.9V REG
(7/7)
ST_UNREG
12
CN001
EP_4.6V
D_3.3V
18
Q6013
BL_H
K14 XRST
28 28
CN002
VDD
20 34
BL_-V
POWER (2/3)
(PAGE 3-9)
11
XSTBY 11
R6072
EP_2.8V
EP_4.6V
1
34
L2802
XSYS_RST
XFLASH_RST
CN6007
VDD
VIDOE/AUDIO
I/O
(3/7)
AU_4.6V
AF16 EMC_XRESET_OUT
B+ SWITCH
L6001
IC2801
Q2801
REG
D_1.8V_FLASH
XFLASH_RST
38
L6002
SDRAM,
NAND
(7/12)
EMC_XRESET_OUT
2
Q6010, Q6011
EP_8.5V
LCD901
L2702
A_2.8V
D_2.8V
FP-914 FLEXIBLE
BOARD
FP-909 FLEXIBLE
BOARD
CN4006
L6003
EP_8.5V
IC2701
L2701
USB_3.3V
F_INTo P11
MS-396 BOARD
CN1110
EP_8.5V
FL2701
R2010
R2011
R2104 D_1.8V_SDRAM
HDMI SIGNAL
PROCESSOR
(1/7)
FL2601
D_1.8V
FP-916
FLEXIBLE
BOARD
IC2601
FB2601
D_2.8V
XE_K
C001
+
CHARGING
CAPACITOR
F4 XRST
D_3.3V
GPIO_S[14] H20
1–3
CN7505
XE_A
32 32
D_3.3V_EX
IC2101
FLASH
DRIVE
POWER (1/3)
(PAGE 3-8)
XFLASH_RST
IC1701
MS_PWR_ON
8 CHG G_IGBT 6
7 XINCHG
4 F_ON
5, 6
R1715
RESET G2
SD1
XHDMI_RST
SCHARGE_ON
XSCHARGE_FULL
STROBO_ON
3
2
1
1, 2
A_2.8V_EX
D_1.2V_EX
50 50
CN1102
(2/2)
Q5001
CN7501
PWM
EXTDA
D_1.2V
A_1.2V_EX_PLL
75 75
LCD_PDG/LCD_Y
/LCD_SNE[4] A28
CN9102
(2/2)
1–4
R1707
R1757
R2008
R2012
CN9034
(2/2)
35 – 37
A_1.2V
A_2.8V
B23 SSP0_RXD
AP19 PCI_RESET
CN1037
(2/2)
POWER (2/3)
(PAGE 3-9)
B
3–5
G
GPIO_S[13] G20
XRESET_REQ
PCI_XRESET
STRB_CHARGE
XSTRB_FULL
STROB_ON
F
AK34 ADC1_IN2
41, 43 – 50
41, 43 – 50
PU_THERM
3, 4
5 XOS VTEMP 3
POWER (2/3)
(PAGE 3-9)
FLASH/CHARGE
CONTROL
FP-912 FLEXIBLE
BOARD
6–8
SE1002
TEMPERATURE
SENSOR
CN1001
HDMI OUT
CN4004
9
MEMORY
STICK DUO
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
39 38
27
26
CN5202
8
1
2
LEVEL3
LD-235 BOARD
1
C001
CHARGING
CAPACITOR
1 2
LENS BLOCK
CN5201
+
1
LEVEL3
SE-174 BOARD (SIDE B)
2
50
ST-186 BOARD ST-186 BOARD
(SIDE B)
(SIDE A)
BT6601
LITHIUM BATTERY
FP-911
FLEXIBLE
BOARD
1
CN6601
IC6904
(Not supplied)
49
CN6902
FP-914 FLEXIBLE
BOARD
LEVEL3
CM-096 BOARD (SIDE A)
FP-905
FLEXIBLE
BOARD
10 11
2 1
11
1
39
CN7505
CN7504
6
1
LEVEL3
SE-174 BOARD (SIDE A)
1
12
FLASH UNIT
(FL27500)
1
FP-910 FLEXIBLE BOARD
6
FP-912
FLEXIBLE
BOARD
8
14
1
CN001
A/V R
1
1
1
CN7503
39
1
1
6
11
1
LENS
BARRIER
UNIT
14
14
CN7501
6
1
FP-915
FLEXIBLE
BOARD
LEVEL3
VC-522 BOARD (SIDE B)
2
1
2
FP-904
FLEXIBLE
BOARD
1
11
10
1
2
CN1029
49
6
1
6
1
CN1026
1
50
CN1030
CN1001
HDMI OUT
2
CN1303
10
1 2
CN1027
10
50
CN002
INTERFACE
CONNECTOR
10
14
BH001
BATTERY
TERMINAL
CPC
(For Check)
SP901
SPEAKER
1
LEVEL3
VC-522 BOARD (SIDE A)
CN1015
38
39
2
1
CN1035
1
49
80
2
50
1
2
CN1036
FP-902
FLEXIBLE
BOARD
LCD901
49
1
1
1
1
6
FP-903
FLEXIBLE
BOARD
39
1
FP-909
FLEXIBLE
BOARD
1
80
79
1
CN1112
1
CN1109
14
14
2
49
50
1
CN1111
CN9102
24
1
1
80
79
1
2
CN9034
6
CN001
1
CN1108
2
1
14
CN1106
3
49
FP-917
FLEXIBLE
BOARD
CN1105
49
24
2
CN002
50
50
50
1
J901
DC IN
1
CN1101
2
39
CN9022
D901
BACKLIGHT
FP-913
FLEXIBLE
BOARD
C
FP-907
FLEXIBLE
BOARD 24
CN1037
79
CN9101
CONTROL
SWITCH
BLOCK
(PH27500)
CN003
49
IC2101
(Not supplied)
1
TOUCH
PANEL
CN003
1
6
2.7 inch
WIDE COLOR
LCD UNIT
1
1
CN002
CN001
39
38
CN1033
CN1011
FP-908 FLEXIBLE
BOARD
MIC901
MICROPHONE
UNIT
2
80
1
1
1
38
39
CN1110
LEVEL3
MD-137 BOARD (SIDE B)
12
2
1
CN1102
79
2
LEVEL3
MD-137 BOARD (SIDE A)
39 38
CN4003
1
2
CONTROL
SWITCH
BLOCK
(PS27500)
CN4004
MEMORY STICK
CONNECTOR
1
2
1
1
1
CN1116
CN4005
6
14
39
38 39
CN4006
MS-396 BOARD
(SIDE B)
2
1
CN6007
26
27
10
1
MS-396 BOARD
(SIDE A)
12
27
39
1
1
FP-916
FLEXIBLE
BOARD
FP-906 FLEXIBLE
BOARD
1
05
HDR-TG1/TG1E/TG3E_L2
4-1
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
FP-910 FLEXIBLE BOARD
(VC-LD CONNECTION)
FP-911 FLEXIBLE BOARD
(VC-SE CONNECTION)
FP-902 FLEXIBLE BOARD
(VC-MD CONNECTION 1)
CONTROL SWITCH BLOCK (PH27500)
FP-905 FLEXIBLE BOARD
(PANEL REVERSE DETECT)
FP-912 FLEXIBLE BOARD
(VC-ST CONNECTION)
FP-903 FLEXIBLE BOARD
(VC-MD CONNECTION 2)
FP-907 FLEXIBLE BOARD
(HDMI CONNECTOR)
FP-904 FLEXIBLE BOARD
(CONTROL SWITCH)
FP-915 FLEXIBLE BOARD
(MD-ST CONNECTION)
FP-913 FLEXIBLE BOARD
(VC-MS CONNECTION)
FP-916 FLEXIBLE BOARD
(MD-MS CONNECTION)
FLASH UNIT (FL27500)
MS-396 BOARD (1/2) (LCD DRIVE)
CONTROL SWITCH BLOCK (PS27500)
MS-396 BOARD (2/2) (CONNECTOR)
FP-908 FLEXIBLE BOARD
(AV/INTERFACE CONNECTOR)
FP-909 FLEXIBLE BOARD (LCD, BACKLIGHT)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
HDR-TG1/TG1E/TG3E_L2
ST-186 BOARD (1/2) (FLASH DRIVE)
ST-186 BOARD (2/2) (CONNECTOR)
FP-914 FLEXIBLE BOARD
(CHARGING CAPACITOR)
FP-906 FLEXIBLE BOARD
(MD-PS CONNECTION)
FP-917 FLEXIBLE BOARD
(BATTERY TERMINAL)
ENGLISH
4-2. SCHEMATIC DIAGRAMS
JAPANESE
4-2. SCHEMATIC DIAGRAMS
(ENGLISH)
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
Color bar chart
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
Pattern box
Front of the lens
L
Kinds of capacitor
External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Camera
A B
A=B
Red
Blue
White
Magenta
H
Cyan
Green
Yellow
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
B A
Fig. a (Video output terminal output waveform)
Electronic beam scanning frame
CRT picture frame
Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
When indicating parts by reference number, please
include the board name.
The components identified by mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
HDR-TG1/TG1E/TG3E_L2
4-2
ENGLISH
4-2. SCHEMATIC DIAGRAMS
JAPANESE
(JAPANESE)
回路図共通ノート
（他に必要なノートは各ブロックに記載してあります）
【回路図ノート】
1. 接続図
・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のもの
はその耐圧を省略。単位はすべてμF（pはpF）。
・チップ抵抗で指示のないものは，1／10W以下。
kΩ＝1000Ω，MΩ＝1000kΩ
・チップ部品交換時の注意
取り外した部品は再使用せず，未使用の部品をご使用くださ
い。
タンタルコンデンサのマイナス側は熱に弱いため注意してくだ
さい。
・チップ部品には下記のように表示したものがあります。
例
C 541
L 452
22U
10UH
TA
A
2520
↑ ↑
↑
種類ケースサイズ
外形寸法（mm）
・抵抗，コンデンサ，ICなど定数にXXがあるものは，使用して
いない事を示しています。このため，使用していない回路が記
載されている事があります。
・★印のある部品は，機種などにより異なりますので機能別マウ
ント一覧表を参照してください。
・可変抵抗と半固定抵抗で，B特性の表示を省略。
・信号名表記について，下記のような場合があります。
XEDIT → EDIT PB/XREC → PB/REC
・2は不燃性抵抗。
・1はヒューズ抵抗。
・Cはパネル表示名称。
・AはB＋ライン。
・BはB−ライン。
・JはBライン（＋，−）の入出力方向を示す。
・Cは調整名称。
パターンボックス
カラーバーチャート
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
パターンボックス
レンズ前面
L
カメラ
2. 図a及び図bの波形が得られるように画枠調整して下さい。
H
シ
黄ア
ン
A B
マ
ゼ
白ン
緑
ダ赤
A=B
青
B A
図a（映像入出力端子出力波形）
電子ビーム走査線
【電圧・波形測定条件ノート】
・電圧値及び信号波形はパターンボックスのカラーバーチャート
を被写体としたときの測定点対アース間の参考値。
（デジタルマルチメータ；入力インピーダンス DC10MΩ使
用）
・使用テスタの入力インピーダンスにより電圧値が多少異なりま
す。
ブラウン管の画像枠
図b（テレビモニタの映像）
イメージャ交換時の注意
・イメージャを交換した場合は，カメラ部の全調整を
行ってください。
・イメージャは構造上，静電気により破壊される恐れが
あるため，MOS ICと同様に注意して取り扱ってくだ
さい。
また，受光部にはゴミの付着，および強い光がはいる
ことのないように注意してください。
0印の部品，または0印付きの点線で囲まれた部品は，
安全性を維持するために重要な部品です。
従って交換時は，必ず指定の部品を使用して下さい。
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定して下さい。
HDR-TG1/TG1E/TG3E_L2
4-3
Schematic diagrams of the CM-096, LD-235 and SE-174 boards are not shown.
Pages from 4-4 to 4-6 are not shown.
HDR-TG1/TG1E/TG3E_L2
2
1
4
3
A
A
39pin
B
VC-522
(12/12)
C
CN1033
Page 4-19
of Level 3
4
3
A
A
1pin
LND001
CMOS_A_3.3V
CMOS_A_3.3V
LND040
LND002
CMOS_A_3.3V
CMOS_A_3.3V
LND041
LND003
ND_NOISE
ND_NOISE
LND042
LND004
REG_GND
REG_GND
LND043
LND005
REG_GND
REG_GND
LND044
1pin
LND001
LND006
ZM_RST_LED
ZM_RST_LED
LND045
LND007
XCS_IC_5201
XCS_IC_5201
LND046
LND008
XCAM_SCK
XCAM_SCK
LND047
LND009
CAM_SI
CAM_SI
LND010
CAM_SO
LND011
D_2.8V
LND012
11pin
REG_GND
REG_GND
LND015
LND002
YAW_AD
YAW_AD
LND016
LND003
REG_GND
REG_GND
LND017
LND004
PITCH_AD
PITCH_AD
LND018
LND048
LND005
REG_GND
REG_GND
LND019
CAM_SO
LND049
LND006
VST_C_RST
VST_C_RST
LND020
D_2.8V
LND050
LND007
REG_GND
REG_GND
LND021
D_2.8V
D_2.8V
LND051
LND008
N.C.
N.C.
LND022
LND013
DIRB1
DIRB1
LND052
LND009
A_2.8V
A_2.8V
LND023
LND014
DIRA1
DIRA1
LND053
LND010
CMOS_A_3.3V
LND015
EN1
EN1
LND054
LND011
BATT_LI_3V
LND016
XRST_IC_5201
XRST_IC_5201
LND055
LND017
REG_GND
REG_GND
LND056
LND018
IC_5201_CLK
IC_5201_CLK
LND057
LND019
REG_GND
REG_GND
LND058
LD-235
LND059
CN5201
Page 4-5
of Level 3
LND020
LENS_COVER_DRV_ON
LND021
IC_5201_VD
LENS_COVER_DRV_ON
IC_5201_VD
LENS_COVER_DIR_PWM
LND060
LENS_COVER_DIR_PWM
LND061
LND023
ZM_RST_SENS
ZM_RST_SENS
LND062
LND024
LENS_DETE
LENS_DETE
LND063
LND025
LENS_TEMP_AD
LENS_TEMP_AD
LND064
LND026
REG_GND
REG_GND
LND065
LND027
REG_GND
REG_GND
LND066
LND022
LND028
NC
SUTTER_XA
SUTTER_XA
LND068
LND030
SUTTER_XA
SUTTER_XA
LND069
NC
NC
SUTTER_A
SUTTER_A
LND071
LND033
SUTTER_A
SUTTER_A
LND072
NC
B
11pin
LND024
BATT_LI_3V
LND025
1pin
VC-522
(12/12)
SE-174
CN6601
Page 4-6
of Level 3
CN1029
Page 4-19
of Level 3
C
C
D
D
D
E
E
E
F
F
C
LND073
NC
LND035
MT_GND
MT_GND
LND074
LND036
MT_GND
MT_GND
LND075
LND037
NC
NC
LND076
LND038
MT_5.0V
MT_5.0V
LND077
LND039
MT_5.0V
MT_5.0V
LND078
39pin
1pin
E
FP-910 FLEXIBLE BOARD
F
CMOS_A_3.3V
B
LND070
LND032
LND034
B
LND067
NC
LND029
LND031
D
2
1
VC-LD CONNECTION
FP-911 FLEXIBLE BOARD
F
VC-SE CONNECTION
(PRINTED WIRING BOARD is omitted.)
(PRINTED WIRING BOARD is omitted.)
05
05
HDR-TG1/TG1E/TG3E_L2
4-7
FP-910, FP-911
Schematic diagrams of the VC-522 board is not shown.
Pages from 4-8 to 4-19 are not shown.
HDR-TG1/TG1E/TG3E_L2
1
2
4
3
5
7
6
8
10
9
11
12
A
A
B
B
MD-137
(7/7)
VC-522
(12/12)
CN1101
Page 4-28
of Level 3
CN1036
Page 4-19
of Level 3
REG_GND
REG_GND
54
C
52
MT_5.0V
MT_5.0V
MT_GND
1
4
MT_5.0V
MT_GND
3
MT_5.0V
MT_5.0V
MT_GND
5
8
REG_GND
I2C_SDA
7
I2C_SDA
REG_GND
10
REG_GND
I2C_SCK
9
I2C_SCK
REG_GND
REG_GND
11
12
14
REG_GND
VR
16
VR
Y_TO_Y
13
REG_GND
15
C_TO_PB
XSYS_RST
18
XSYS_RST
V_TO_PR
17
V_TO_PR
FR_XRESET
20
FR_XRESET
REG_GND
19
REG_GND
A_1.8V
22
A_1.8V
USB_3.3V
21
USB_3.3V
A_2.8V
24
A_2.8V
CMOS_A_3.3V
23
CMOS_A_3.3V
CMOS_D_2.8V
26
CMOS_D_2.8V
A_4.6V
25
A_4.6V
IC_1301_D_1.2V
28
IC_1301_D_1.2V
BATT_LI_3V
27
BATT_LI_3V
IC_1301_D_1.2V
30
IC_1301_D_1.2V
D_3.3V
29
D_3.3V
IC_1301_D_1.2V
32
IC_1301_D_1.2V
D_1.2V
31
D_1.2V
IC_1301_D_1.2V
34
IC_1301_D_1.2V
D_1.2V
33
D_1.2V
IC_1301_D_1.2V
D_2.8V
36
38
IC_1301_D_1.2V
D_2.8V
D_2.8V
40
D_2.8V
SPDIF_O
42
SPDIF_O
CEC_INT
44
CEC_INT
XQUICKREC_LED
46
XQUICKREC_LED
REG_GND
REG_GND
48
50
REG_GND
REG_GND
D_1.2V
D_1.2V
35
37
D_1.2V
D_1.2V
REG_GND
39
CLK_SYS_OUT_CEC
41
CLK_SYS_OUT_CEC
REG_GND
43
REG_GND
ADA_BCK
45
ADA_BCK
ADA_LRCK
ADA_FCK
47
49
MT_5.0V
MT_GND
49
48
MT_5.0V
MT_GND
47
46
MT_5.0V
MT_GND
45
REG_GND
44
REG_GND
REG_GND
I2C_SDA
43
I2C_SDA
42
REG_GND
I2C_SCK
41
I2C_SCK
40
REG_GND
REG_GND
39
REG_GND
38
REG_GND
Y_TO_Y
37
Y_TO_Y
VR
36
VR
C_TO_PB
35
C_TO_PB
XSYS_RST
34
FR_XRESET
ADA_LRCK
ADA_FCK
XSYS_RST
V_TO_PR
33
V_TO_PR
32
FR_XRESET
REG_GND
31
REG_GND
USB_3.3V
29
USB_3.3V
CMOS_A_3.3V
27
CMOS_A_3.3V
A_4.6V
25
A_4.6V
30
A_1.8V
A_2.8V
28
A_2.8V
CMOS_D_2.8V
26
CMOS_D_2.8V
IC_1301_D_1.2V
24
IC_1301_D_1.2V
BATT_LI_3V
23
BATT_LI_3V
IC_1301_D_1.2V
22
IC_1301_D_1.2V
D_3.3V
21
D_3.3V
IC_1301_D_1.2V
20
IC_1301_D_1.2V
D_1.2V
19
D_1.2V
IC_1301_D_1.2V
18
IC_1301_D_1.2V
D_1.2V
17
D_1.2V
IC_1301_D_1.2V
16
IC_1301_D_1.2V
D_1.2V
15
D_1.2V
D_2.8V
14
D_2.8V
D_1.2V
13
D_1.2V
D_2.8V
12
D_2.8V
REG_GND
11
REG_GND
SPDIF_O
10
SPDIF_O
CLK_SYS_OUT_CEC
9
CLK_SYS_OUT_CEC
CEC_INT
8
CEC_INT
REG_GND
7
REG_GND
XQUICKREC_LED
6
XQUICKREC_LED
ADA_BCK
5
ADA_BCK
REG_GND
4
REG_GND
ADA_LRCK
3
ADA_LRCK
REG_GND
2
REG_GND
ADA_FCK
1
ADA_FCK
52
54
53
REG_GND
A_1.8V
REG_GND
C
MT_GND
REG_GND
Y_TO_Y
C_TO_PB
53
50
MT_GND
6
REG_GND
E
2
REG_GND
REG_GND
D
CN9022 50P 51
D
E
CN9101 50P 51
REG_GND
REG_GND
F
F
G
G
FP-902 FLEXIBLE BOARD
H
H
VC-MD CONNECTION 1
05
HDR-TG1/TG1E/TG3E_L2
4-20
FP-902
1
2
4
3
5
7
6
8
10
9
11
12
A
A
MD-137
(7/7)
VC-522
(12/12)
CN1102
CN1037
Page 4-19
of Level 3
Page 4-28
of Level 3
REG_GND
REG_GND
84
B
82
REG_GND
1
REG_GND
4
REG_GND
USB_D+
3
6
REG_GND
USB_D-
5
USB_D-
HM_VD
8
HM_VD
REG_GND
7
REG_GND
10
HM_HD
9
HM_FLD
REG_GND
12
REG_GND
HM_B0
14
HM_B1
16
HM_B2
HM_FLD
11
REG_GND
HM_B0
HM_Y0
13
HM_Y0
HM_B1
HM_Y1
15
HM_Y1
18
HM_B2
HM_Y2
17
HM_Y2
HM_B3
20
HM_B3
HM_Y3
19
HM_Y3
HM_B4
22
HM_B4
HM_Y4
21
HM_Y4
HM_B5
24
HM_B5
HM_Y5
23
HM_Y5
HM_B6
26
HM_B6
HM_Y6
25
HM_Y6
HM_B7
28
HM_B7
HM_Y7
27
HM_Y7
REG_GND
30
REG_GND
REG_GND
29
REG_GND
HM_R0
32
HM_R0
HM_R4
31
HM_R4
34
HM_R1
HM_R2
36
HM_R2
HM_R3
38
HM_R3
REG_GND
40
REG_GND
HMCK
42
HMCK
44
REG_GND
HM_R5
33
HM_R5
HM_R6
35
HM_R6
HM_R7
37
HM_R7
REG_GND
39
REG_GND
41
HM74CK
HM74CK
REG_GND
43
XMODE_SW
46
XMODE_SW
XBB_SCK
45
48
STABLE_RUN
BB_SI
47
BB_SI
50
XHDMI_RST
BB_SO
49
BB_SO
52
XEX_RST
51
XCS_IC_2601
XHDMI_RST
XEX_RST
XFLASH_RST
54
XFLASH_RST
REG_GND
56
REG_GND
IC_2401_Y_OUT
58
IC_2401_Y_OUT
IC_2401_C/PB_OUT
60
IC_2401_C/PB_OUT
REG_GND
62
IC_2201_D_1.2V
IC_2201_D_1.2V
64
66
REG_GND
IC_2201_D_1.2V
IC_2201_D_1.2V
XCS_IC_2601
XFR_SCK
53
XBB_SCK
XFR_SCK
FR_SI
55
FR_SI
FR_SO
57
FR_SO
ADA_SIA0
59
ADA_SIA0
ADA_SOA0
61
ADA_SOA0
ADA_SOA1
63
XCS_IC_2801
65
ADA_SOA1
XCS_IC_2801
IC_2201_D_1.2V
68
IC_2201_D_1.2V
XCS_EX
67
XCS_EX
IC_2201_D_1.2V
70
IC_2201_D_1.2V
D_1.8V
69
D_1.8V
REG_GND
72
REG_GND
D_1.8V
71
D_1.8V
REG_GND
74
REG_GND
A_1.2V
73
A_1.2V
SP-
76
SP-
SP+
78
SP+
SYS_SOUND
80
SYS_SOUND
SD1
75
SD1
MS_PWR_ON
77
MS_PWR_ON
REG_GND
REG_GND
79
REG_GND
USB_D+
78
USB_D+
REG_GND
77
REG_GND
USB_D-
76
75
REG_GND
74
USB_DREG_GND
REG_GND
REG_GND
BOOT_MODE_PORT0
79
BOOT_MODE_PORT0
73
71
HM_FLD
REG_GND
69
REG_GND
HM_Y0
HM_VD
HM_HD
72
REG_GND
70
REG_GND
HM_B0
68
HM_B0
HM_Y0
67
HM_B1
66
HM_B1
HM_Y1
65
HM_Y1
HM_B2
64
HM_B2
HM_Y2
63
HM_Y2
HM_B3
62
HM_B3
HM_Y3
61
HM_Y3
HM_B4
60
HM_B4
HM_Y4
59
HM_Y4
HM_B5
58
HM_B5
HM_Y5
57
HM_Y5
HM_B6
56
HM_B6
HM_Y6
55
HM_Y6
HM_B7
54
HM_B7
HM_Y7
53
HM_Y7
REG_GND
52
REG_GND
REG_GND
51
HM_R0
50
HM_R0
HM_R4
49
HM_R4
HM_R1
48
HM_R1
HM_R5
47
HM_R5
HM_R2
46
HM_R2
HM_R6
45
HM_R6
HM_R3
44
HM_R3
HM_R7
REG_GND
42
REG_GND
HM_R7
43
REG_GND
41
HM74CK
REG_GND
HMCK
40
39
HM74CK
REG_GND
38
REG_GND
REG_GND
37
REG_GND
XMODE_SW
36
XMODE_SW
XBB_SCK
35
XBB_SCK
STABLE_RUN
34
STABLE_RUN
BB_SI
33
BB_SI
XHDMI_RST
32
XHDMI_RST
BB_SO
31
BB_SO
XCS_IC_2601
29
XCS_IC_2601
XFR_SCK
27
XFR_SCK
XEX_RST
30
XEX_RST
XFLASH_RST
28
XFLASH_RST
REG_GND
26
REG_GND
IC_2401_Y_OUT
24
IC_2401_Y_OUT
IC_2401_C/PB_OUT
REG_GND
22
IC_2401_C/PB_OUT
C
REG_GND
HMCK
FR_SI
25
FR_SI
FR_SO
23
FR_SO
ADA_SIA0
21
ADA_SIA0
20
REG_GND
ADA_SOA0
19
IC_2201_D_1.2V
18
IC_2201_D_1.2V
ADA_SOA1
17
ADA_SOA1
IC_2201_D_1.2V
16
IC_2201_D_1.2V
XCS_IC_2801
15
XCS_IC_2801
IC_2201_D_1.2V
14
IC_2201_D_1.2V
XCS_EX
13
XCS_EX
IC_2201_D_1.2V
12
IC_2201_D_1.2V
D_1.8V
11
D_1.8V
D_1.8V
9
D
ADA_SOA0
REG_GND
10
REG_GND
REG_GND
8
REG_GND
A_1.2V
7
A_1.2V
SP-
6
SP-
SD1
5
SD1
SP+
4
SP+
MS_PWR_ON
3
MS_PWR_ON
2
SYS_SOUND
BOOT_MODE_PORT0
1
BOOT_MODE_PORT0
CN9102
81
SYS_SOUND
83
HM_VD
HM_FLD
HM_HD
82
84
B
80
REG_GND
STABLE_RUN
83
REG_GND
USB_D+
REG_GND
REG_GND
E
REG_GND
81
REG_GND
HM_R1
D
REG_GND
CN9034
REG_GND
HM_HD
C
2
80P
80P
D_1.8V
E
REG_GND
REG_GND
F
F
G
G
FP-903 FLEXIBLE BOARD
H
H
VC-MD CONNECTION 2
05
HDR-TG1/TG1E/TG3E_L2
4-21
FP-903
Schematic diagrams of the MD-137 board is not shown.
Pages from 4-22 to 4-28 are not shown.
HDR-TG1/TG1E/TG3E_L2
2
1
4
3
4
3
2
1
Note: SP901 is not included in
FP-904 flexible complete board.
CHASSIS
24PIN
HDMI OUT
TMDS_DATA1_SHIELD
5
TMDS_DATA1+
GND
6
TMDS_DATA1-
GND
7
TMDS_DATA0_SHIELD
TMDS_ DATA0+
8
TMDS_DATA0+
TMDS_ DATA0-
9
TMDS_DATA0-
1pin
GND
10
TMDS_CLOCK_SHIELD
GND
11
TMDS_CLOCK+
TMDS_ CLOCK+
12
TMDS_CLOCK-
TMDS_ CLOCK-
13
DDC_CEC_GND
GND
14
CEC
CEC
15
SCL
GND
16
SDA
SCL
17
RESERVED
SDA
18
+5V_POWER
+5V_POWER
19
HPD
B
B
10pin
SP-
LND101
SP+
LND107
REG_GND
LND106
FR_XRESET
LND109
XBATT_VIEW
LND105
KEY_AD0(PHOTO_REC)
LND104
KEY_AD0(PHOTO_FREEZE)
LND108
KEY_AD0(EASY)
LND103
C
S001
RESET
SP-
B
SP+
CN001
REG_GND
REG_GND
VC-522
(12/12)
C
HPD
LND102
LND110
+5V_POWER
CN1027
Page 4-19
of Level 3
GND
REG_GND
2
N.C.
3
KEY_AD0(PHOTO_FREEZE)
4
N.C.
5
KEY_AD0(PHOTO_REC)
6
N.C.
2
4
3
S008
EASY
1PIN
6P
1
1
C
3
4
TMDS_ DATA1-
SP901
SPEAKER
2P
1
TMDS_ DATA1+
CN002
2
TMDS_DATA2-
SP(+)
1
TMDS_DATA2+
3
SP(-)
1
SP-
2
GND
2
SP+
GND
21
TMDS_DATA2_SHIELD
20
1
22
CN1106
Page 4-28
of Level 3
TMDS_ DATA2-
23
B
MD-137
(7/7)
CN1001 19P
4
TMDS_ DATA2+
3
GND
A
VDR003
XX
VDR001
XX
A
VDR002
XX
LND111
A
A
CONTROL
SWITCH
BLOCK
(PH27500)
C
Page 4-35
of Level 2
CHASSIS_GND
S002
4
2
DISP/
BATT INFO
D
D
D
D
E
E
E
E
F
F
FP-904 FLEXIBLE BOARD
F
FP-907 FLEXIBLE BOARD
CONTROL SWITCH
F
XX MARK:NO MOUNT
HDMI CONNECTOR
05
05
HDR-TG1/TG1E/TG3E_L2
4-29
FP-907, FP-904
1
2
3
4
1
A
B
REG_GND
LND078
LND038
REG_GND
REG_GND
LND037
REG_GND
REG_GND
LND036
MSX_BIO2
LND035
D
1pin
4
A
39pin
1pin
LND001
INT_MIC_F
INT_MIC_F
LND040
LND077
LND002
INT_MIC_R
INT_MIC_R
LND041
LND076
LND003
INT_MIC_L
INT_MIC_L
LND042
MSX_BIO2
LND075
LND004
MIC_GND
MIC_GND
LND043
MSX_BIO0
MSX_BIO0
LND074
LND005
N.C.
N.C.
LND044
LND034
MSX_BS
MSX_BS
LND073
LND006
EP_4.6V
EP_4.6V
LND045
LND033
MSX_BIO1
MSX_BIO1
LND072
LND007
BL_-V
BL_-V
LND046
LND032
MSX_BIO3
MSX_BIO3
LND071
LND008
BL_CONT
BL_CONT
LND047
REG_GND
REG_GND
LND009
REG_GND
REG_GND
LND048
LND030
MSX_CLK
MSX_CLK
LND069
LND010
REG_GND
REG_GND
LND049
LND029
REG_GND
REG_GND
LND068
LND011
BB_SO
BB_SO
LND050
LND028
REG_GND
REG_GND
LND067
LND012
XBB_SCK
XBB_SCK
LND051
LND027
KEY_AD1
KEY_AD1
LND066
LND013
BB_SI
BB_SI
LND052
LND026
TP_X
TP_X
LND065
LND014
REG_GND
REG_GND
LND053
LND025
ZOOM_VR_AD
ZOOM_VR_AD
LND064
LND015
REG_GND
REG_GND
LND054
LND024
TP_SEL1
TP_SEL1
LND063
LND016
WD_DIS
WD_DIS
LND055
LND023
TP_Y
TP_Y
LND062
LND017
KEY_AD1
KEY_AD1
LND056
LND022
REG_GND
REG_GND
LND061
LND018
HDMI_JACK_IN
HDMI_JACK_IN
LND057
LND021
PANEL_HD
PANEL_HD
LND060
LND019
START/STOP
START/STOP
LND058
LND020
PANEL_VD
PANEL_VD
LND059
LND020
XPHOTO_LED
XPHOTO_LED
LND059
LND019
REG_GND
REG_GND
LND058
LND021
PANEL_O/C_REV_CN
PANEL_O/C_REV_CN
LND060
LND018
REG_GND
REG_GND
LND057
LND022
PANEL_O/C_NOR_CN
PANEL_O/C_NOR_CN
LND061
LND017
WD_DIS
WD_DIS
LND056
LND023
XHOT_STBY
XHOT_STBY
LND062
LND016
HDMI_JACK_IN
HDMI_JACK_IN
LND055
LND024
JACK_AD
JACK_AD
LND063
LND015
START/STOP
START/STOP
LND054
LND025
ZOOM_VR_AD
ZOOM_VR_AD
LND064
LND014
XPHOTO_LED
XPHOTO_LED
LND053
LND026
XVBUS_DET
XVBUS_DET
LND065
LND013
PANEL_O/C_NOR_CN
PANEL_O/C_NOR_CN
LND052
LND027
XBATT_VIEW
XBATT_VIEW
LND066
LND012
PANEL_O/C_REV_CN
PANEL_O/C_REV_CN
LND051
LND028
XMS_IN
XMS_IN
LND067
LND011
XHOT_STBY
XHOT_STBY
LND050
LND029
REG_GND
REG_GND
LND068
LND010
JACK_AD
JACK_AD
LND049
LND030
REG_GND
REG_GND
LND069
LND009
XVBUS_DET
XVBUS_DET
LND048
LND031
REG_GND
REG_GND
LND070
LND008
XBATT_VIEW
XBATT_VIEW
LND047
LND032
REG_GND
REG_GND
LND071
LND007
XMS_ACC_LED
XMS_ACC_LED
LND046
LND033
XPOWER_SW
XPOWER_SW
LND072
LND006
XCS_LCD
XCS_LCD
LND045
LND034
D_2.8V
D_2.8V
LND073
LND005
REG_GND
REG_GND
LND044
LND035
MS_VCC
MS_VCC
LND074
LND004
REG_GND
REG_GND
LND043
LND036
MS_VCC
MS_VCC
LND075
LND003
PANEL_G
PANEL_G
LND042
LND037
MS_VCC
MS_VCC
LND076
LND002
PANEL_B
PANEL_B
LND041
LND039
EP_8.5V
EP_8.5V
LND078
LND001
PANEL_R
PANEL_R
LND040 39pin
LND038
EP_2.8V
EP_2.8V
LND077
LND031
C
1pin
REG_GND
LND039
3
A
A
39pin
2
LND070
B
B
C
C
D
D
1pin
VC-522
(12/12)
MS-396
(2/2)
CN1035
Page 4-19
of Level 3
MD-137
(7/7)
MS-396
(2/2)
CN4005
Page 4-32
of Level 2
CN1110
Page 4-28
of Level 3
CN4006
Page 4-32
of Level 2
E
E
VC-MS CONNECTION
C
D
39pin
E
E
FP-916 FLEXIBLE BOARD
FP-913 FLEXIBLE BOARD
F
B
F
F
MD-MS CONNECTION
F
(PRINTED WIRING BOARD is omitted.)
(PRINTED WIRING BOARD is omitted.)
05
05
HDR-TG1/TG1E/TG3E_L2
4-30
FP-913, FP-916
1
2
4
3
5
7
6
8
10
9
A
12
11
TP_X
L6003
10uH
10uH
L6002
EP_8.5V
EP_4.6V
TP_Y
R6072
0
TP_Y
2.8
TP_R
L6001
TP_SEL1
5
EP_2.8V
Q6001
XP411F-TXE
C6036
XX
C6038
22u
6.3V
C6037
0.1u
B
10V
C6042
1u
B
C6043
1u
B
2.8
0
D_2.8V
2.8
1
6
C6033
2.2u
B
6.3V
4
C6032
22u
4V
3
10uH
C6031
10u
5
2
2.8
1
2
3
REG_GND
C6001
0.0047u
B
4
3
B
1
6
6
D6001
XX
PANEL_COM
C6002
0.0047u
B
0
10k
R6067
2.2
2
4.1
1.4
2.8
2.6
1.6
1.6
1.6
2.8
1.2
4.7u B
Q6001, Q6002
TOUCH PANEL
I/F
D6003
XX
2.8
B
6.3V
C6045
6.3V
EXTDA
R6065
10k
4.7u
5
0
PANEL_REF
C6044
Q6002
XP421F-TXE
2
PANEL_R
B
25V
B
25V
B
25V
4
C6039
0.01u
C6040
0.01u
C6041
0.01u
PANEL_B
PANEL_G
XX R6082
B
A
TP_X
TP_BOT
REG_GND
GND
COMDA
COMOUT
REF
COMREF
XLED
BLDET
EXTDA
BIN
GIN
RIN
VCC1
Filter1
39 38 37 36 35 34 33 32 31 30 29 28 27
C6046
0.1u
B
10V
R6064 91k 1.2
C
C6034
0.1u
B
1.2
C6035
560p
CH
R6061
68k
1.4
0.2
BB_SI
2.7
XCS_LCD
R6062
0
2.6
XBB_SCK
0.3
BB_SO
2.8
2.6
PANEL_HD
VP
Filter2
VCC2
GND1
VB
OPOUT
VG
OPIN
IC6001
TEST
CXM3006CER-T4
VR
GND2
LCD DRIVE
SO
PWM
XCS
WIDE
XSCK
VST
SI
VDD
VDD
VCK
SCAN
VSS
XHD
GND
14 15 16 17 18 19 20 21 22 23 24 25 26
52 51 50 49 48 47 46 45 44 43 42 41 40
Q6011
MCH6305-TL-E-S
GND
2.5
PANEL_VP
8.5
4.6
6
5
2
1
4
2.5 R6069 0
PANEL_VB
2.5
R6070
R6041
100k
0
PANEL_VG
R6071
2.5
3
0
5.8
PANEL_VR
Q6010, Q6011
B+ SWITCH
2.8
R6042
220k
BL_ON
8.5
C
C6025
0.01u
B
25V
D6004
XX
0
CN6007
PANEL_VST
R6039
0
2.8
1.4
PANEL_XSTBY
PANEL_VCK
C6023
XX
0
2.8
Q6010
UNRF2A300AS0
HST
PCG
8
9
10 11 12 13
2.1
2.8
C6024
PANEL_EN
2.8
PANEL_VD
REG_GND
10V B
1u
PANEL_DWN
PANEL_XSTBY
TP_TOP
2
TP_BOT
3
TP_L
PANEL_COM
4
TP_R
PANEL_VST
5
PANEL_VCK
6
COM/CS
PANEL_EN
7
VST
PANEL_DWN
8
VCK
9
EN
EN
HCK2
7
DWN
HCK1
6
2.8
RGT
5
0.1
VSS
4
0
XCLR
3
1.4
CLKIN
2
1.4
XVD
1
2.8
GND
XSTBY
D
27P
1
R6043
120k
C6026
1u
B 10V
0
Q6013
2SA207900AS0
SWITCH
D6005
R6045
1M
MAZS056G08S0
5.5
PANEL_XSTBY
N.C.
10
DWN
11
VDD
12
VSS
13
VSSG
14
XSTBY
PANEL_PCG
15
PCG
C6027
16
HST
B
0.1u
17
REF
PANEL_PCG
PANEL_HST
R6066
0
PANEL_HST
PANEL_HCK2
R6068
PANEL_REF
0
PANEL_HCK1
REG_GND
PANEL_HCK2
18
PANEL_HCK1
19
HCK1
PANEL_VP
20
PSIG
PANEL_VG
21
G
PANEL_VR
22
R
D
FP-909
FLEXIBLE
LND001 – LND027
Page 4-34
of Level 2
HCK2
PANEL_RGT
E
PANEL_VB
23
B
PANEL_RGT
24
RGT
PANEL_COM
25
COM
BL_H
26
BL_H
27
BL_L
BL_-V
E
F
F
BL_ON
EP_2.8V
2.8V
Q6018 – Q6020
BACKLIGHT DRIVE
EP_4.6V
R6083
2200
4.4
4
2.8
4.4 5
C6047
XX
G
2
3
1
R6086
22
4.6
6
2.8
Q6018
1
DTA144EMFS6T2L
4.5
BL_H
BL_H
Q6019
1 HN1B04FE-Y/GR(TPLR3)
4.4
R6085
22k
BL_CONT
R6084
3300
6
5
1
C6048
XX
2.8
4
2.1
BL_CONT
G
R6089
15k
R6087
4700
2.7
2
3
R6088
22k
R6090
18k
EXTDA
EXTDA
2.6
1
Q6020
HN1B04FE-Y/GR(TPLR3)
2.1
REG_GND
MS-396 BOARD (1/2)
H
H
LCD DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
05
HDR-TG1/TG1E/TG3E_L2
4-31
MS-396 (1/2)
1
2
4
3
A
5
7
6
8
9
10
11
12
A
REG_GND
EP_2.8V
39
EP_2.8V
EP_8.5V
38
EP_8.5V
MS_VCC
37
MS_VCC
MS_VCC
36
MS_VCC
35
D_2.8V
34
33
XPOWER_SW
32
REG_GND
REG_GND
31
REG_GND
30
REG_GND
29
XMS_IN
28
XBATT_VIEW
27
XBATT_VIEW
XVBUS_DET
26
XVBUS_DET
D
INT_MIC_L
4
MIC_REG_GND
5
INT_MIC_R
6
INT_MIC_L
INT_MIC_R
MIC_GND
B
XMS_IN
ZOOM_VR_AD
24
XHOT_STBY
23
PANEL_O/C_NOR_CN
22
PANEL_O/C_REV_CN
21
PANEL_O/C_REV_CN
XPHOTO_LED
20
XPHOTO_LED
START/STOP
19
START/STOP
HDMI_JACK_IN
18
KEY_AD1
17
KEY_AD1
WD_DIS
16
WD_DIS
REG_GND
15
REG_GND
REG_GND
14
BB_SI
13
XBB_SCK
12
BB_SO
11
BB_SO
REG_GND
10
REG_GND
REG_GND
9
BL_CONT
8
BL_CONT
BL_-V
7
BL_-V
EP_4.6V
6
EP_4.6V
N.C.
5
MIC_GND
4
MIC_GND
INT_MIC_L
3
INT_MIC_L
INT_MIC_R
2
INT_MIC_R
1
INT_MIC_F
JACK_AD
XHOT_STBY
PANEL_O/C_NOR_CN
HDMI_JACK_IN
C
BB_SI
D_2.8V
XBB_SCK
D
R4001
MS_VCC
C4001
0.1u
B 10V
MS_VCC
0
REG_GND
REG_GND
R4007
120
MSX_BIO0
G
H
MSX_BS
120
120
R4005
FB4003
FB4004
R4006
0
REG_GND
3
MSX_BIO2
4
MSX_BIO2
MSX_BIO0
5
MSX_BIO0
MSX_BS
6
MSX_BS
MSX_BIO1
7
MSX_BIO1
MSX_BIO3
8
MSX_BIO3
REG_GND
9
REG_GND
MSX_CLK
10
MSX_CLK
REG_GND
REG_GND
11
REG_GND
12
KEY_AD1
13
TP_X
14
TP_X
ZOOM_VR_AD
15
ZOOM_VR_AD
TP_SEL1
16
TP_Y
9
VCC
8
MS_SCLK
7
MSDATA3
6
XMS_IN
5
MSDATA2
4
MEMORY
STICK
DUO
MSDATA0
3
MSDATA1
2
MSBS
1
VSS
CN4004
LND401
VSS
E
10P
REG_GND
LND402
KEY_AD1
F
TP_SEL1
TP_Y
S4001
18
REG_GND
POWER
PANEL_HD
19
PANEL_HD
PANEL_VD
20
PANEL_VD
REG_GND
21
REG_GND
REG_GND
22
WD_DIS
23
WD_DIS
HDMI_JACK_IN
24
HDMI_JACK_IN
START/STOP
25
START/STOP
XPHOTO_LED
26
XPHOTO_LED
PANEL_O/C_NOR_CN
27
PANEL_O/C_NOR_CN
PANEL_O/C_REV_CN
28
PANEL_O/C_REV_CN
XHOT_STBY
29
XHOT_STBY
JACK_AD
30
JACK_AD
XVBUS_DET
31
XVBUS_DET
XBATT_VIEW
32
XBATT_VIEW
XMS_ACC_LED
33
XMS_ACC_LED
XCS_LCD
XCS_LCD
34
REG_GND
35
REG_GND
36
REG_GND
PANEL_G
37
PANEL_G
PANEL_B
38
PANEL_B
PANEL_R
39
PANEL_R
XPOWER_SW
2
17
REG_GND
41
R4002
R4003
4
Page 4-30
of Level 2
2
MSX_BIO1
1
LND040 – LND078
REG_GND
REG_GND
3
FP-913
FLEXIBLE
1
VDR401
F
CN4005
REG_GND
FB4001
FB4002
120
MSX_BIO2
39P
0
R4004
XMS_IN
REG_GND
10
MSX_CLK
MSX_BIO3
E
(MS ACCESS)
XMS_ACC_LED
CN4006
39P
INT_MIC_F
Note: MIC901 is not included in
MS-396 complete board.
JACK_AD
INT_MIC_F
3
12
C
2
MIC_REG_GND
11
Page 4-30
of Level 2
1
INT_MIC_F
470
LND040 – LND078
R
6P
MIC_REG_GND
CL-271HR-C-TS
FP-916
FLEXIBLE
D_2.8V
XPOWER_SW
25
CN4003
FRONT
L
REG_GND
ZOOM_VR_AD
MIC901
MICROPHONE UNIT
R4008
B
40
D4002
41
REG_GND
G
MS-396 BOARD (2/2)
40
H
CONNECTOR
05
HDR-TG1/TG1E/TG3E_L2
4-32
MS-396 (2/2)
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
3
2
4
5
6
7
8
CHASSIS_GND
LND001
C002
220p
A
C001
220p
A
REG_GND
2
LANC_SIG
3
S_GND
3
LANC_SIG_AV
R001
JACK_AD_AV
3
FB002
GND VOUT2
SE001
PANEL
OPEN/CLOSE
DETECT
0
LANC_DC_AV
VDD VOUT1
1
VIDEO/D3_PR_AV
S_C/D3_PB_AV
2
3
R002
R003
S_Y/D3_Y_AV
3
0
0
4
LANC_DC
5
S_C/D3_Pb
A/V R
6
AUDIO_R
7
MULTI_JACK_IN
8
VIDEO/AUDIO_GND
9
VIDEO/D3_Pr
10
13
REG_GND
11
AUDIO_R_I/O_AV
12
1
REG_GND
4
AUDIO_L
AUDIO_L_I/O_AV
14
FB001
PANEL_O/C_REV_CN
S_Y/D3_Y
CN001 10P
B
EVER_3.0V
B
Note: CN002 (interface connector) is not supplied, but this
is included in FP-908 flexible complete board.
PANEL_O/C_NOR_CN
CHASSIS_GND
LND002
MD-137
(7/7)
(INTERFACE CONNECTOR)
for Handycam station
CN1111
Page 4-28
of Level 3
CN002 42P
53
54
2
ACV_UNREG
ACV_UNREG
1
4
ACV_UNREG
ACV_UNREG
3
6
N.C
N.C
5
8
VIDEO_I/O
REG_GND
7
10
REG_GND
Y
9
12
S_C_I/O
REG_GND
11
14
REG_GND
16
S_Y_I/O
18
REG_GND
49
ACV_UNREG
ACV_UNREG
50
47
ACV_UNREG
ACV_UNREG
48
45
ACV_UNREG
ACV_UNREG
46
43
ACV_UNREG
ACV_UNREG
44
41
ACV_UNREG
VIDEO/D3_Pr
42
VIDEO/D3_PR
39
N.C. (REG_GND)
S_C/D3_Pb
40
S_C/D3_PB
JACK_AD_CRADLE
37
MULTI_JACK_IN
S_Y/D3_Y
38
S_Y/D3_Y
KEY_AD1
35
(DVD BURN)
REG_GND
36
REG_GND
33
BATT/XEXT
AUDIO_L_I/O
34
AUDIO_L_I/O
AUDIO_L_I/O
20
31
LANC_DC
AUDIO_R_I/O
32
AUDIO_R_I/O
AUDIO_R_I/O
29
LANC_SIG
USB_GND
30
REG_GND
USB_VCC
27
USB_VBUS
USB_D+
28
USB_D+
REG_GND
25
REG_GND
USB_D-
26
USB_D-
23
REG_GND
USB_GND
24
REG_GND
21
ACV_GND
ACV_GND
19
ACV_GND
17
ACV_UNREG
C
REG_GND
BATT/XEXT_CR
LANC_DC
LANC_SIG
D
ACV_GND
ACV_UNREG
VIDEO/D3_PR
S_C/D3_PB
C
Pb
13
REG_GND
15
Pr
17
AUDIO_L
DET
19
22
AUDIO_R
CTRL1
21
24
REG_GND
CTRL2
23
26
MULTI_JACK_IN
CTRL3
25
28
(USB_ID)
N.C
27
USB_VCC
30
USB_DET/VBUS
N.C
29
22
REG_GND
32
USB_GND
LANC_SIG
31
LANC_SIG
ACV_GND
20
USB_D+
34
USB_D+
LANC_DC
33
LANC_DC
ACV_GND
ACV_GND
18
USB_D-
36
USB_D-
BATT/XEXT_CR
35
BATT/XEXT_CR
15
ACV_GND
ACV_GND
16
REG_GND
38
USB_GND
PON(DVD BURN)
37
KEY_AD1
13
ACV_GND
AUDIO_L_I/O
14
AUDIO_L_I/O_AV
40
ACV_GND
ACV_GND
39
LANC_SIG
AUDIO_R_I/O
12
AUDIO_R_I/O_AV
42
ACV_GND
ACV_GND
41
MULTI_JACK_IN
REG_GND
10
REG_GND
LANC_SIG_AV
11
JACK_AD_AV
9
LANC_DC_AV
ACV_UNREG
REG_GND
JACK_AD_CRADLE
ACV_GND
7
LANC_DC
VIDEO/D3_Pr
8
VIDEO/D3_PR_AV
5
EVER_3.0V
S_C/D3_Pb
6
S_C/D3_PB_AV
3
PANEL_O/C_NOR_CN
S_Y/D3_Y
4
S_Y/D3_Y_AV
1
PANEL_O/C_REV_CN
REG_GND
2
REG_GND
51 CN003
S_Y/D3_Y
ACV_GND
D
43 44
50P 52
PANEL_O/C_REV_CN
E
E
PANEL_O/C_NOR_CN
EVER_3.0V
FP-908 FLEXIBLE BOARD
AV/INTERFACE CONNECTOR
F
F
NO MARK:REC/PB MODE
05
HDR-TG1/TG1E/TG3E_L2
4-33
FP-908
1
2
3
4
5
6
7
8
A
A
Note: D901 and LCD901 are not included
in FP-909 flexible complete board.
B
B
LCD901
6
N.C.
5
TP_TOP
4
TP_BOT
3
N.C.
2
TP_L
1
TP_R
CN003
1pin
C
D
E
6P
LND027
TP_TOP
LND026
TP_BOT
24
COM
LND025
TP_L
23
CS
LND024
TP_R
22
VST
LND023
N.C.
21
VCK
LND022
COM/CS
20
EN
LND021
VST
19
DWN
LND020
VCK
18
VDD
LND019
EN
17
VSS
LND018
DWN
16
LND017
VDD
15
VSSG
LND016
VSS
14
XSTBY
LND015
VSSG
13
PCG
LND014
XSTBY
12
HST
LND013
PCG
11
REF
LND012
HST
10
N.C
LND011
REF
9
N.C.
LND010
HCK2
8
HCK2
LND009
HCK1
7
HCK1
LND008
PSIG
6
PSIG
LND007
G
5
G
LND006
R
4
R
LND005
B
3
B
LND004
RGT
2
RGT
LND003
COM
1
COM
LND002
BL_H
27pin LND001
BL_L
MS-396
(1/2)
CN6007
Page 4-31
of Level 2
TOUCH
PANEL
C
N.C
CN002
2.7 inch
WIDE
COLOR
LCD
UNIT
D
24P
6
BL_H
5
BL_H
4
N.C.
3
N.C.
2
BL_L
1
BL_L
CN001
D901
(BACKLIGHT)
E
6P
FP-909 FLEXIBLE BOARD
F
F
LCD, BACKLIGHT
05
HDR-TG1/TG1E/TG3E_L2
4-34
FP-909
1
2
4
3
1
A
A
2
4
3
A
A
6pin
1pin
1pin
REG_GND
N.C.
KEY_AD1(PHOTO_FREEZE)
B
(PHOTO FREEZE)
N.C.
S001
KEY_AD1(PHOTO_REC)
B
B
6pin
PHOTO
LND001
N.C.
N.C.
LND015
LND002
N.C.
N.C.
LND016
LND003
N.C.
N.C.
LND017
LND004
STRB_CHARGE
STRB_CHARGE
LND018
LND005
XSTRB_FULL
XSTRB_FULL
LND019
LND006
STROB_ON
STROB_ON
LND020
(PHOTO REC)
N.C.
S002
6pin
FP-904
FLEXIBLE
VC-522
(12/12)
ST-186
(2/2)
CN1026
Page 4-19
of Level 3
CN7501
Page 4-37
of Level 2
1pin
B
CN001
Page 4-29
of Level 2
CONTROL SWITCH BLOCK
(PH27500)
C
C
FP-912 FLEXIBLE BOARD
C
CONTROL SWITCH BLOCK (PH27500) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
C
VC-ST CONNECTION
(PRINTED WIRING BOARD is omitted.)
05
05
1
2
1
4
3
A
2
A
A
A
IC001
AN48830B-NL
1pin
LND001
ST_UNREG
ST_UNREG
1pin
LND026
LND002
ST_UNREG
ST_UNREG
LND027
LND003
ST_UNREG
ST_UNREG
LND028
LND004
MT_5.0V
MT_5.0V
LND029
LND005
MT_5.0V
MT_5.0V
LND030
LND006
ST_GND
ST_GND
LND031
LND007
ST_GND
ST_GND
LND032
LND008
ST_GND
ST_GND
LND033
LND009
ST_GND
ST_GND
LND034
LND010
N.C.
N.C.
LND035
LND011
N.C.
N.C.
LND036
LND012
N.C.
N.C.
LND037
LND013
N.C.
N.C.
LND038
LND014
N.C.
N.C.
LND039
CN1030
Page 4-19
of Level 3
B
LND003
LND004
N.C.
LND005
REG_GND
LND006
1PIN
REG_GND
3
2
N.C.
2.8
PANEL_NOR/REV
1
LND002
VC-522
(12/12)
D_2.8V
5
LND001
2.8
4
PANEL REVERSE
DETECT
6PIN
B
B
14pin
C
4
3
FP-905 FLEXIBLE BOARD
MD-137
(7/7)
ST-186
(2/2)
CN1112
Page 4-28
of Level 3
CN7503
Page 4-37
of Level 2
B
14pin
C
C
PANEL REVERSE DETECT
C
FP-915 FLEXIBLE BOARD
NO MARK:REC/PB MODE
MD-ST CONNECTION
(PRINTED WIRING BOARD is omitted.)
05
05
HDR-TG1/TG1E/TG3E_L2
4-35
PH27500, FP-905, FP-912, FP-915
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
3
2
4
6
5
8
7
T5001
A
2
C5005
220p
50V
L5001
2.2uH
9
12
D5003
CRF02 (TE85R)
A
6
R5008
4700
1
D5002
XE_A
4
RB520S-40TE61
C5004
10u
B
10V
XE_A
ST_GND
3
5
ST_GND
1.8
G_IGBT
10
2.8
Q5001
TIG032TS-S-TL-E
11
R5004
100k
SCHARGE_ON
XE_K
C5002
0.1u
B
10V
C5003
2.2u
B
6.3V
D5001
XX
R5006
XX
R5007
XX
5
6
8
R5010
100
7
FLASH
DRIVE
ST_UNREG
C5001
XX
280
1
I_PEAK
0
0
2
5
R5003
330k
CHG
XINCHG
4
0
FLASH/CHARGE
CONTROL
9
F_ON
PGND
8
VCC
5
7
SW
NC
6
1
2
8.3
3
8.3
4
R5005
0
VBAT
B
TPS65552DGQR
IC5001
HGND
B
C
11
10
3
1
0
C
R5011
1M
CL5001
XSCHARGE_FULL
R5001
XX
STROBO_ON
MT_5.0V
ST_GND
D
D
R5002
0
LD5001
GND
E
E
F
F
G
G
ST-186 BOARD (1/2)
H
H
FLASH DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
05
HDR-TG1/TG1E/TG3E_L2
4-36
ST-186 (1/2)
1
3
2
4
5
6
7
8
A
A
14p
FP-915
FLEXIBLE
B
LND026 – LND039
Page 4-35
of Level 2
CN7503
ST_UNREG
1
ST_UNREG
2
ST_UNREG
3
MT_5.0V
4
MT_5.0V
5
ST_GND
ST_GND
7
ST_GND
8
ST_GND
9
R7501 0
MT_5.0V
C7501
0.1u
B
10V
10
11
N.C.
12
N.C.
13
ST_GND
4
N.C
5
N.C
6
XE_A
7
XE_A
8
FP-914
FLEXIBLE
LND001 – LND008
Page 4-38
of Level 2
XE_A
B
8P
C
7
6
N.C.
5
XE_A
N.C.
4
STRB_CHARGE
3
SCHARGE_ON
2
XSCHARGE_FULL
6p
ST_GND
3
15
8
STROB_ON
ST_GND
2
14
N.C.
XSTRB_FULL
1
CN7505
N.C.
C
XE_A
ST_GND
N.C.
16
LND015 – LND020
Page 4-35
of Level 2
ST_UNREG
6
N.C.
FP-912
FLEXIBLE
ST_GND
1
CN7501
12
XE_A
11
XE_A
10
XE_A
9
STROBO_ON
ST_GND
XE_K
D
N.C
8
N.C
7
ST_GND
6
ST_GND
5
N.C
4
N.C
3
XE_K
2
XE_K
1
XE_K
CN7504
FLASH UNIT
(FL27500)
LND001 – LND003
LND006, LND007
LND010 – LND012
Page 4-38
of Level 2
D
12P
E
E
ST-186 BOARD (2/2)
F
F
CONNECTOR
05
HDR-TG1/TG1E/TG3E_L2
4-37
ST-186 (2/2)
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
2
4
3
A
A
1Pin
LND050
XE-K
LND001
XE_K
XE-K
LND002
XE-K
LND003
LND052
COMMON
LND053
XENON
LAMP
N.C.
C001
0.033u
B
250V
N.C.
TRIGEER
LND006
ST_GND
LND007
N.C.
R001
1M
1/8W
B
ST_GND
ST-186
(2/2)
CN7504
Page 4-37
of Level 2
B
N.C.
XE_A
XE-A
LND010
XE-A
LND011
XE-A
LND012
12Pin
LND051
FLASH UNIT
C
C
(FL27500)
FLASH UNIT (FL27500) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
05
1
2
4
3
A
A
1Pin
ST-186
(2/2)
B
CN7505
Page 4-37
of Level 2
LND001
ST_GND
LND002
ST_GND
LND003
ST_GND
LND004
N.C
LND005
N.C
LND006
XE_A
LND007
XE_A
LND008
8pin
XE_A
C001
37u
330V
CHARGING
CAPACITOR
B
Note: C001 is not included in FP-914 flexible board.
C
FP-914 FLEXIBLE BOARD
C
CHARGING CAPACITOR
05
HDR-TG1/TG1E/TG3E_L2
4-38
FLASH UNIT, FP-914
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
4
3
2
1
1
2
4
3
CHASSIS
A
A
A
VDR001
XX
A
12pin
LND010
14pin
LND015
REG_GND
LND012
D_2.8V
LND013
ZOOM_VR
CN1116
14P
START/STOP
1
START/STOP
START/STOP
REG_GND
D_2.8V
ZOOM_VR
CHARGE_LED_VDD
XCHARGE_LED
B
D001
FLASH/CHG
B
S001
STILL/MOVIE
SELECT
B
LND002
LND004
XPHOTO_LED
LND005
MODE_LED_VDD
LND007
XCAM_LED
LND006
XQUICK_LED
XMODE_SW
LND016
QUICK_LED_VDD
REG_GND
LND009
XCHARGE_LED
QUICK_LED_VDD
XQUICK_LED
D004
QUICK ON
D003
XCAM_LED
MOVIE
MODE_LED_VDD
D002
XPHOTO_LED
STILL
REG_GND
T
LND008
1pin
T ZOOM t W
XPHOTO_LED
MODE_LED_VDD
D_2.8V
4
ZOOM_VR
5
REG_GND
6
REG_GND
7
XMODE_SW
8
XPHOTO_LED
9
XCAM_LED
XQUICKREC_LED
QUICK_LED_VDD
XCHARGE_LED
CHARGE_LED_VDD
CHARGE_LED_VDD
REG_GND
3
MODE_LED_VDD
10
XCAM_LED
11
XQUICK_LED
12
QUICK_LED_VDD
13
XCHARGE_LED
14
CHARGE_LED_VDD
CONTROL
SWITCH
BLOCK
(PS27500)
B
Page 4-39
of Level 2
RV001
ZOOM_VR
D_2.8V
MD-137
(7/7)
REG_GND
1pin
C
CN1109
Page 4-28
of Level 3
C
START/STOP
C
XMODE_SW
XMODE_SW
2
C
FP-906 FLEXIBLE BOARD
S004
FP-906
FLEXIBLE
MD-PS CONNECTION
CN1116
Page 4-39
of Level 2
START/STOP
05
1
D
2
4
3
D
A
A
1Pin
BATT_GND
BATT_GND
Note: BH001 is not included in FP-917 flexible board.
BATT_GND
BATT_GND
4
BH001
BATTERY
TERMINAL
E
B
E
BATT_GND
BATT_GND
C
2
BATT_SIG
N.C.
1
BATT_UNREG
MD-137
(7/7)
CN1105
Page 4-28
of Level 3
B
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
14pin
CONTROL SWITCH BLOCK
(PS27500)
F
CONTROL SWITCH BLOCK (PS27500) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
C
F
C
FP-917 FLEXIBLE BOARD
BATTERY TERMINAL
05
05
HDR-TG1/TG1E/TG3E_L2
4-39
PS27500, FP-906, FP-917
4-3. PRINTED WIRING BOARDS
Link
FP-902 FLEXIBLE BOARD
FP-908 FLEXIBLE BOARD
FP-903 FLEXIBLE BOARD
FP-909 FLEXIBLE BOARD
FP-907 FLEXIBLE BOARD
ST-186 BOARD
FP-904 FLEXIBLE BOARD
FP-906 FLEXIBLE BOARD
MS-396 BOARD
FP-914 FLEXIBLE BOARD
FP-905 FLEXIBLE BOARD
FP-917 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
HDR-TG1/TG1E/TG3E_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
(ENGLISH)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
•
•
: Uses unleaded solder.
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
• Chip parts.
Transistor
B
(JAPANESE)
プリント図共通ノート
【プリント図ノート】
・
・
：無鉛半田を使用しています。
：基板
：フレキシブル配線板
見ている面側のパターン。
：裏側のパターン
（他のパターンについては表示されていません）
・スルーホールは省略。
・プリント図には，本機で使用していない部品が記載されている
場合があります。
・Cはパネル表示名称。
HDR-TG1/TG1E/TG3E_L2
4-40
Diode
6 5 4 4 5 6 5
C
E
4 4
3
5
3
3
1 23
1 2 3 3 2 1 1 2 3 3 2 1
2
1 2
1 2
1
4
3
3
4 6 5 4 4 5 6
2
1 1 2 3 3 2 1
2 2
1 3
2
5 4 3 3 4 5 4
1
1
2
3
2
4
1
1 6 54
Printed wiring boards of the CM-096, LD-235, SE-174 and VC-522 boards are not shown.
Pages from 4-41 to 4-43 are not shown.
HDR-TG1/TG1E/TG3E_L2
FP-902 (2 layers), FP-903 (2 layers)
: Uses unleaded solder.
FP-902 FLEXIBLE BOARD
51
53
1
49
CN9101
52
2
50
54
50
54
52
2
CN9022
49
1
53
51
11
1-875-823-
05
FP-903 FLEXIBLE BOARD
81
82
1
CN9102
2
84
83
80
79
CN9034
79
80
83
84
2
1
82
81
1-875-824-
11
05
HDR-TG1/TG1E/TG3E_L2
4-44
FP-902, FP-903
Printed wiring boards of the MD-137 board is not shown.
Page 4-45 is not shown.
HDR-TG1/TG1E/TG3E_L2
FP-907 (2 layers), FP-904 (1 layer), MS-396 (4 layers)
: Uses unleaded solder.
FP-907 FLEXIBLE BOARD
FP-904 FLEXIBLE BOARD
1
LND102
LND107
LND109
LND104
LND110
LND101
LND106
LND105
CN001
LND108
LND103
6
10
1
2
2
4
VDR002
1
S001
22
CN002
VDR001
1
3
CN1001
19
23
1
RESET
HDMI OUT
1-875-828-
DISP/
BATT INFO
11
3
24
1
EASY
3
1
VDR003
S008
20
21
1
S002
4
2
2
4
1-875-825-
05
11
05
R6064
C6041
R6090
C6040
R6088
6
R6084
R6085
CN4003
1
26
B
3
C6037
1
40
1
CN4006
L6003
2
12
10
R4001
C6027
D6001
3
CN4004
6
38
39
41
2
CN4005
1
40
R4006
11
4
3
MEMORY
STICK
DUO
1
Q6002
R4005 FB4003
6
1
1
R4002 FB4002
Q6001
(MS ACCESS)
LND401
D4002
A
05
1-874-701-
K
11
R4008
D6003
4
POWER
R4004
C6002
3
2
FB4001
1
4
1
C4001
4
6
41
2
C6001
R4007
C6024
E
B
R4003 FB4004
C
Q6013
R6043
C6026
D6005
39
38
S4001
R6045
27
E
CN6007
Q6018
C
C6038
6
4
Q6019
1
3
R6067
R6083
P
C6046
R6069
26
27
D6004
LND402
R6086
C6048
L6002
R6082
IC6001
C6044
C6045
C6043
6
4
Q6020
1
3
C6047
R6039
C6042
R6087
R6089
R6065
40
39
C6034
R6061
1
52
C6036
R6066
MS-396 BOARD (SIDE B)
VDR401
C6031
R6068
B
13
14
R6041
C6023
6
E
R6071
1
Q6011
Q6010
R6070
R6042
C
4
P
R6072
C6032
C6025
C6035
C6039
P
L6001
3
C6033
R6062
MS-396 BOARD (SIDE A)
1-874-701-
11
05
HDR-TG1/TG1E/TG3E_L2
4-46
FP-907, FP-904, MS-396
FP-905 (1 layer), FP-908 (2 layers), FP-909 (1 layer)
: Uses unleaded solder.
FP-905 FLEXIBLE BOARD
3
FP-909 FLEXIBLE BOARD
1
IC001
6
5
CN003
24
1
1
CN002
6
CN001
1
LND105
6
LND103
05
LND101
LND102
LND104
LND106
4
1
1-875-826- 11
51
53
1
49
CN003
52
2
50
54
FP-908 FLEXIBLE BOARD
27
LND001
LND002
LND004
4
1
LND003
LND005
SE001
LND006
LND002
LND007
3
2
LND008
LND009
LND010
1-875-829-
LND011
11
LND012
LND013
LND014
LND015
LND016
LND017
LND018
44
42
CN002
LND019
2
41
1
LND020
43
LND021
LND022
LND023
LND024
LND025
LND027
(INTERFACE CONNECTOR)
05
LND026
1
1-875-830-
11
Note: CN002 (interface connector) is not supplied,
but this is included in FP-908 flexible complete board.
2 6 1
14
13
R001
R003
A/V R
10 5 9
R002
CN001
4 8 3 7
FB002
C002
12
11
C001
FB001
05
LND001
HDR-TG1/TG1E/TG3E_L2
4-47
FP-905, FP-908, FP-909
ST-186 (4 layers), FP-906 (1 layer), FP-914 (1 layer), FP-917 (1 layer)
: Uses unleaded solder.
A
8
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
FP-914 FLEXIBLE BOARD
ST-186 BOARD (SIDE A)
1
K
D5003
2
6
R7501
4
C7501
R5008
C5005
8
1
CN7505
3
5
D5002
T5001
1
1
14
16
CN7503
15
05
1-874-696-
11
R5001
A
CN7504
12
LD5001
6
R5003
1
R5002
R5007
1
10
D5001
IC5001
11
R5004
5
C5003
R5005
4
R5006
K
C5004
1
1
C5002
Q5001
R5011
7
CN7501
8
6
R5010
8
CL5001
L5001
5
ST-186 BOARD (SIDE B)
C5001
05
1-874-696-
11
FP-917 FLEXIBLE BOARD
1
14
FP-906 FLEXIBLE BOARD
VDR001
LND011
1
CN1116
14
+
>P1<
C001
CHARGING
CAPACITOR
Note: C001 is not included in
FP-914 flexible board.
F2 2
FP-916-
05
1-875-835-
11
Note: BH001 is not included in
FP-917 flexible board.
2
FP-917-
1
BH001
BATTERY
TERMINAL
+
C
12
LND010
LND015
LND012
LND013
LND002
LND004
LND005
LND007
LND006
LND016
LND009
LND008
>P1<
05
−
4
1
1-875-827- 11
05
HDR-TG1/TG1E/TG3E_L2
4-48E
1-875-838-
11
ST-186, FP-906, FP-914, FP-917
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
EXPLODED VIEWS
Link
A
OVERALL SECTION
B
C
D
FRONT CABINET SECTION
MAIN FRAME SECTION-1
MAIN FRAME SECTION-2
F
G
H
E
LENS SECTION
Link
CABINET (R) SECTION
BT FRAME SECTION
LCD PANEL SECTION
ELECTRICAL PARTS LIST
ACCESSORIES
FP-902 FLEXIBLE BOARD
D
FP-906 FLEXIBLE BOARD
D
FP-914 FLEXIBLE BOARD
F
FP-903 FLEXIBLE BOARD
D
FP-907 FLEXIBLE BOARD
C
FP-917 FLEXIBLE BOARD
D
FP-904 FLEXIBLE BOARD
F
FP-908 FLEXIBLE BOARD
F
MS-396 BOARD
B
FP-905 FLEXIBLE BOARD
C
FP-909 FLEXIBLE BOARD
H
ST-186 BOARD
D
HDR-TG1/TG1E/TG3E_L2
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
•
Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-TG1/TG1E/TG3E_L2
5-1
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定してください。
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重要な部品です。
従って交換時は，
必ず指定の部品を使用してください。
• 外装部品色表示
例：
(SILVER):セットの色を表す。
(Silver) : 部品の色を表す。
5. REPAIR PARTS LIST
DISASSEMBLY
5-1. EXPLODED VIEWS
HARDWARE LIST
5-1-1. OVERALL SECTION
ns: not supplied
6
#14
5
3
#2
#14
4
1 (Note)
7
#2
#2
#2
ns
#14
8
MIC901
9
2
#5
#2
Front Cabinet Section
(See Page 5-3)
Note: When you exchange CABINET (L), SERVICE be
sure to read “1-4. PRECAUTION ON REPLACING THE CABINET (L)” on page 1-3.
Note: サービス用キャビネット（L）交換時は1-7ペー
ジの“1 - 4 . キャビネット（L ）交換時の注意”
を必ずお読みください。
Ref. No.
Part No.
Description
1
2
* 3
4
5
(Note)
3-870-675-01
3-300-089-01
X-2189-879-1
3-300-102-01
CABINET (L), SERVICE
GASKET (JN)
SHEET (TL), GUARD
CABINET ASSY, INNER (TOP)
CABINET, TOP
6
7
Ref. No.
Part No.
Description
8
3-300-104-01 SHIELD, MICROPHONE
9
3-300-046-01 FRAME, MICROPHONE
MIC901 1-542-754-11 MICROPHONE UNIT
#2
#5
#14
1-480-606-11 SWITCH BLOCK, CONTROL (PS27500)
3-873-223-01 SHEET (TOP), RADIATION
HDR-TG1/TG1E/TG3E_L2
5-2
2-635-562-31 SCREW (M1.7) (Black)
3-080-204-01 SCREW, TAPPING, P2 (Black)
2-599-475-11 SCREW (M1.7) (Silver)
5. REPAIR PARTS LIST
DISASSEMBLY
HARDWARE LIST
5-1-2. FRONT CABINET SECTION
57 (23mm X 13mm)
#5
59
58
56
#14
#14
#5
#3
MS
-39
6
55
53
#14
52
#5
#14
51
54
#14
Main Frame Section-1
(See Page 5-4)
CAUTION:
For the part of 57, cut WOVEN (T0.25), FABRIC NON (3076-631-01) into the desired length and use it.
CAUTION:
57番は，T0.25ヒメロン
（3-076-631-01）
を切って使用。
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
51
52
53
* 54
55
56
3-300-076-01
X-2189-888-1
A-1494-203-A
3-300-077-01
A-1528-451-A
RING, LENS
CABINET (F) ASSY
LENS BARRIER UNIT
FRAME, RING
MS-396 BOARD, COMPLETE
Ref. No.
Part No.
Description
57
58
0 59
#3
CAUTION
3-300-105-01
1-480-610-11
2-660-401-01
SHEET, MIC
HOLDER, STROBOSCOPE
FLASH UNIT (FL27500)
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
#5
#14
3-300-047-01 HOLDER, MS
HDR-TG1/TG1E/TG3E_L2
5-3
3-080-204-01 SCREW, TAPPING, P2 (Black)
2-599-475-11 SCREW (M1.7) (Silver)
5. REPAIR PARTS LIST
HARDWARE LIST
DISASSEMBLY
5-1-3. MAIN FRAME SECTION-1
ns: not supplied
Main Frame Section-2
(See Page 5-5)
107
ns
#3
BT6601
#14
106
#3
#14
108
#14
#14
#3
#14
#14
104
#3
105
Cabinet (R) Section
(See Page 5-7)
103
101
102
! : BT6601
(BATTERY, LITHIUM SECONDARY)
Board on the mount position.
(See page 4-42 on level 3)
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
102
103
104
105
A-1528-467-A
3-300-093-01
3-300-086-01
3-873-225-01
3-300-090-01
FP-907 FLEXIBLE BOARD, COMPLETE
SHEET, MI RADIATION
FRAME, JK
SHEET (BR), GUARD
SHEET (A), VC
107
108
0 BT6601
#3
A-1528-449-A
A-1528-465-A
1-528-999-61
2-660-401-01
SE-174 BOARD, COMPLETE
FP-905 FLEXIBLE BOARD, COMPLETE
BATTERY, LITHIUM SECONDARY
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
106
1-875-832-11 FP-911 FLEXIBLE BOARD
#14
HDR-TG1/TG1E/TG3E_L2
5-4
2-599-475-11 SCREW (M1.7) (Silver)
5. REPAIR PARTS LIST
DISASSEMBLY
HARDWARE LIST
5-1-4. MAIN FRAME SECTION-2
164
ns: not supplied
163
165
#3
166
#3
167
160
13
D-
156
M
162
Lens Section
(See Page 5-6)
7
161
168
#14
159
157
#14
158
BH001
ns
154
155
154
153
52
VC
152
• Refer to page 5-1 for mark 0.
Ref. No.
151
152
152
153
154
* 155
* 156
157
158
159
160
161
Part No.
#3
151
Description
Ref. No.
1-875-834-11 FP-913 FLEXIBLE BOARD
A-1530-418-A VC-522 BOARD, COMPLETE (SERVICE) (TG1)
A-1530-419-A VC-522 BOARD, COMPLETE (SERVICE)
(TG1E/TG3E)
3-300-091-01 SHEET (A), RADIATION
3-300-101-01 SHEET, AG COPY
3-300-081-01
3-300-083-01
1-875-838-11
A-1528-452-A
A-1528-464-A
2
FRAME (FRONT), MAIN
FRAME (REAR), MAIN
FP-917 FLEXIBLE BOARD
FP-902 FLEXIBLE BOARD, COMPLETE
FP-903 FLEXIBLE BOARD, COMPLETE
HDR-TG1/TG1E/TG3E_L2
5-5
Description
A-1530-421-A MD-137 BOARD, COMPLETE (SERVICE) (TG3E)
3-873-224-01 SPACER, MD
3-300-088-01 LABEL, FUSE REPLACEMENT CAUTION
164
165
166
167
168
A-1528-466-A
1-875-837-11
A-1528-450-A
1-875-833-11
1-875-836-11
0 BH001
#3
#14
3-300-092-01 SHEET (N), RADIATION
A-1530-420-A MD-137 BOARD, COMPLETE (SERVICE)
(TG1/TG1E)
Part No.
161
162
163
FP-906 FLEXIBLE BOARD, COMPLETE
FP-916 FLEXIBLE BOARD
ST-186 BOARD, COMPLETE
FP-912 FLEXIBLE BOARD
FP-915 FLEXIBLE BOARD
1-780-597-11 TERMINAL BOARD, BATTERY
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
2-599-475-11 SCREW (M1.7) (Silver)
Ver. 1.2 2008.09
The changed portions from
Ver. 1.1 are shown in blue.
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-5. LENS SECTION
ns: not supplied
#9
202
209
203
210
#3
#14
5
-23
LD
212
211
205
(including IC6903 and IC6904
(CMOS imager)) (Note)
ns
206
201
#14
#14
207
204
#5
208
Note: Be sure to read “Precautions for Replacement of
Imager” on page 4-2 when changing the imager.
Note: イメージャの交換時は4 - 3 ページの“イメージャ交
換時の注意”を必ずお読みください。
Ref. No.
Part No.
Description
Ref. No.
Part No.
201
202
202
203
204
1-875-831-11
A-1528-468-A
A-1543-261-A
X-2189-889-1
1-788-710-11
FP-910 FLEXIBLE BOARD
LD-235 BOARD, COMPLETE (TG1)
LD-235 BOARD, COMPLETE (TG1E/TG3E)
HEAT SINK ASSY, CM
OPTICAL UNIT (CH001)
* 209
3-878-478-01 SHEET, URU
205
A-1528-469-A CM-096 BOARD, COMPLETE (including IC6903
and IC6904 (CMOS imager)) (Note)
3-300-080-01 SHEET, CM RADIATION
3-300-079-01 HEAT SINK (R), CM
3-300-078-01 FRAME, LENS
* 210
211
212
#3
#5
2-887-640-01
1-788-737-11
3-279-478-01
2-660-401-01
3-080-204-01
206
207
208
HDR-TG1/TG1E/TG3E_L2
5-6
#9
#14
Description
SHEET (BL), PROTECTION
OPTICAL FILTER BLOCK (OFB-05-06)
RUBBER (CH001), SEAL
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
SCREW, TAPPING, P2 (Black)
3-078-890-21 SCREW, TAPPING (Silver)
2-599-475-11 SCREW (M1.7) (Silver)
5. REPAIR PARTS LIST
DISASSEMBLY
HARDWARE LIST
5-1-6. CABINET (R) SECTION
265
266
#14
261
LCD Panel Section
(See Page 5-9)
#14
#14
260
#14
259
#14
262
#2
263
264
256
258
J901
257
254
#5
255
253
BT Frame Section
(See Page 5-8)
C001
252
#2
#2
251
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
* 251
252
253
254
255
3-300-053-01
3-300-051-01
3-300-052-01
1-875-835-11
3-300-050-01
SHEET, CAPACITOR
HOLDER, CAPACITOR
COVER, CAPACITOR
FP-914 FLEXIBLE BOARD
WASHER, TRIPOD
* 262
263
264
* 265
3-300-059-01
A-1528-472-A
X-2189-883-1
3-300-060-01
BLIND, VC
FP-904 FLEXIBLE BOARD, COMPLETE
BUTTON ASSY, CF
STABILIZER
* 256
* 257
258
259
260
3-300-055-01
3-300-054-01
3-300-049-01
A-1528-473-A
3-300-099-01
FRAME, BOTTOM
RETAINER, TERMINAL
HOLDER, JK
FP-908 FLEXIBLE BOARD, COMPLETE
SPACER, CR
* 266
0 C001
0 J901
#2
#5
3-300-061-01
1-114-722-11
1-821-769-11
2-635-562-31
3-080-204-01
BLIND, HINGE
ELECT
37uF
330V
JACK, DC (DC IN)
SCREW (M1.7) (Black)
SCREW, TAPPING, P2 (Black)
* 261
3-300-057-01 RETAINER, CF BUTTON
#14
HDR-TG1/TG1E/TG3E_L2
5-7
2-599-475-11 SCREW (M1.7) (Silver)
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-7. BT FRAME SECTION
ns: not supplied
310
ns
311
SP901
#14
312
#14
313
317
316
#14
309
308
#27
314 315
#47
307
#14
306
305
304
303
302
301
Ref. No.
Part No.
Description
301
301
302
303
304
3-300-107-01
3-300-107-11
3-300-008-01
3-300-005-01
3-300-007-01
PLATE (R), ORNAMENTAL (TG1/TG1E)
PLATE (R), ORNAMENTAL (TG3E)
CUSHION, PANEL
CABINET (R)
SHEET, BT SLIDER
305
306
307
308
* 309
3-300-010-01
3-300-006-01
X-2189-882-1
3-873-201-01
3-300-056-01
SHAFT, STRAP
RETAINER (LOWER), BT LID
FRAME ASSY, BT
SHEET (BT), RADIATION
RETAINER, SPEAKER
310
Ref. No.
3-300-058-01 SHEET, BT PROTECTION
HDR-TG1/TG1E/TG3E_L2
5-8
Part No.
Description
311
312
313
314
X-2318-015-1
3-300-106-01
3-300-009-01
3-300-000-01
BT LOCK HOOK ASSY
COVER, CPC
SPRING, BT LID
COVER, BT LINK
315
316
317
SP901
#14
3-299-999-01
X-2189-881-1
3-300-103-01
1-826-837-11
2-599-475-11
SPRING, BT LINK
PLATE ASSY, BT SLIDE
LID, BT
SPEAKER (1.3CM)
SCREW (M1.7) (Silver)
#27
#47
2-662-396-11 SCREW (M1.4), NEW, TRUSTAR, P2 (Black)
2-665-774-01 SCREW (Silver)
5. REPAIR PARTS LIST
360
HARDWARE LIST
5-1-8. LCD PANEL SECTION
ns: not supplied
359
361
358
362
353
(Note)
ns
#1
363 #14
356
355
#1
351
ns
ns
357
352
(3.8mm X 3.8mm)
#14
354
364
D901
LCD901
ns
CAUTION:
For the part of 356, cut SHEET, ADHESIVE (2-649-30001) into the desired length and use it.
#2
CAUTION:
356番は，接着紙
（2-649-300-01）
を切って使用。
ns
368
369
Note: Be sure to read “HELP 5: THE METHOD OF ATTACHMENT OF FP-909 FLEXIBLE BOARD” when
you install the FP-909 flexible board.
Note: FP-909フレキシブル基板取付け時は「HELP 5: THE
METHOD OF ATTACHMENT OF FP-909 FLEXIBLE
BOARD」を必ずお読みください。
365
367
366
Ref. No.
Part No.
Description
351
352
353
354
355
3-300-066-01
X-2189-884-1
3-300-069-01
1-480-607-11
3-300-068-01
COVER (REAR), HINGE
HINGE ASSY
COVER, F HINGE
SWITCH BLOCK, CONTROL (PH27500)
COVER, PH BUTTON
356
357
358
359
360
CAUTION
3-300-065-01
3-300-100-01
3-300-070-01
3-300-062-01
SHEET, PH ADHESIVE
COVER (FRONT), HINGE
SHEET, JN COPY
CLAMP, HINGE
CABINET (C), P
361
362
363
X-2318-318-1 CUSHION ASSY, TP
A-1528-470-A FP-909 FLEXIBLE BOARD, COMPLETE (Note)
X-2189-886-1 SPACER ASSY, PANEL
Ref. No.
Part No.
Description
364
365
3-300-064-01 RETAINER, LCD
3-300-071-01 GUIDE (CHIBITOKU), PANEL
366
367
368
369
D901
3-300-072-01
X-2189-885-1
X-2189-887-1
1-471-278-11
1-480-681-11
HOOK, PANEL
CABINET (M) ASSY, P
BAND ASSY, PANEL COVER
MAGNET
BLOCK, LIGHT GUIDE PLATE (2.7)
(BACKLIGHT)
LCD901
#1
#2
#14
HDR-TG1/TG1E/TG3E_L2
5-9
A-1438-502-A
2-635-562-11
2-635-562-31
2-599-475-11
TP BLOCK ASSY (27ESTMG08)
SCREW (M1.7) (Black)
SCREW (M1.7) (Black)
SCREW (M1.7) (Silver)
Electrical parts list of the CM-096 board is
not shown.
Page 5-10 is not shown.
HDR-TG1/TG1E/TG3E_L2
FP-902
FP-903
FP-904
FP-905
FP-906
FP-907
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
A-1528-452-A FP-902 FLEXIBLE BOARD, COMPLETE
******************************
Part No.
FP-908
FP-909
FP-914
FP-917
Description
< CONNECTOR >
CN001
0 CN002
< CONNECTOR >
* CN9022 1-820-778-11 CONNECTOR, BOARD TO BOARD
* CN9101 1-820-778-11 CONNECTOR, BOARD TO BOARD
* CN003
1-815-794-13 CONNECTOR (MULTIPLE) (A/V R)
(Not supplied) CONNECTOR, MULTIPLE (SOCKET)
(INTERFACE CONNECTOR)
(CN002 is supplied including in FP-908 flexible complete board.)
1-820-778-11 CONNECTOR, BOARD TO BOARD
< FERRITE BEAD >
A-1528-464-A FP-903 FLEXIBLE BOARD, COMPLETE
******************************
FB001
FB002
1-400-927-31 BEAD, FERRITE (1005)
1-400-927-31 BEAD, FERRITE (1005)
< CONNECTOR >
< RESISTOR >
* CN9034 1-821-894-11 CONNECTOR, BOARD TO BOARD 80P
* CN9102 1-821-894-11 CONNECTOR, BOARD TO BOARD 80P
R001
R002
R003
A-1528-472-A FP-904 FLEXIBLE BOARD, COMPLETE
******************************
0
0
0
< SENSOR >
< CONNECTOR >
* CN001
CN002
1-218-990-81 SHORT CHIP
1-218-990-81 SHORT CHIP
1-218-990-81 SHORT CHIP
* SE001
1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P
1-794-375-21 PIN, CONNECTOR 2P
1-480-627-11 SENSOR, MAGNETIC
A-1528-470-A FP-909 FLEXIBLE BOARD, COMPLETE
******************************
< SWITCH >
< CONNECTOR >
S001
S002
S008
1-771-138-21 SWITCH, KEY BOARD (RESET)
1-771-138-21 SWITCH, KEY BOARD (DISP/BATT INFO)
1-771-138-21 SWITCH, KEY BOARD (EASY)
* CN001
* CN002
* CN003
A-1528-465-A FP-905 FLEXIBLE BOARD, COMPLETE
******************************
1-875-835-11 FP-914 FLEXIBLE BOARD
********************
(C001 is not included in FP-914 flexible board.)
< IC >
IC001
1-818-619-71 CONNECTOR, FFC/FPC (ZIF) 6P
1-821-835-71 CONNECTOR, FFC/FPC (ZIF) 24P
1-818-619-71 CONNECTOR, FFC/FPC (ZIF) 6P
< CAPACITOR >
6-705-011-01 IC AN48830B-NL
0 C001
1-114-722-11 ELECT
37uF
330V
A-1528-466-A FP-906 FLEXIBLE BOARD, COMPLETE
******************************
1-875-838-11 FP-917 FLEXIBLE BOARD
********************
(BH001 is not included in FP-917 flexible board.)
< CONNECTOR >
* CN1116 1-816-645-51 FFC/FPC CONNECTOR (LIF) 14P
< BATTERY TERMINAL >
0 BH001
A-1528-467-A FP-907 FLEXIBLE BOARD, COMPLETE
******************************
Electrical parts list of the LD-235 and MD137 boards are not shown.
Pages 5-12 to 5-16 are not shown.
< CONNECTOR >
CN1001 1-821-166-21 CONNECTOR, HDMI (HDMI OUT)
A-1528-473-A FP-908 FLEXIBLE BOARD, COMPLETE
******************************
(CN002 (interface connector) is not supplied,
but this is included in FP-908 flexible complete board.)
< CAPACITOR >
C001
C002
1-164-933-11 CERAMIC CHIP
1-164-933-11 CERAMIC CHIP
220PF
220PF
10%
10%
1-780-597-11 TERMINAL BOARD, BATTERY
50V
50V
• Refer to page 5-1 for mark 0.
HDR-TG1/TG1E/TG3E_L2
5-11
MS-396
Ref. No.
Part No.
Description
Ref. No.
A-1528-451-A MS-396 BOARD, COMPLETE
***********************
Q6018
Q6019
Q6020
< CAPACITOR >
C4001
C6001
C6002
C6024
C6025
1-125-777-11
1-100-581-81
1-100-581-81
1-165-908-11
1-100-567-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.0047uF
0.0047uF
1uF
0.01uF
10%
10%
10%
10%
10%
10V
50V
50V
10V
25V
C6026
C6027
C6031
C6032
C6033
1-165-908-11
1-125-777-11
1-112-534-11
1-127-895-91
1-165-884-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
1uF
0.1uF
10uF
22uF
2.2uF
10%
10%
20%
20%
10%
10V
10V
6.3V
4V
6.3V
C6034
C6035
C6037
C6038
C6039
1-125-777-11
1-164-739-11
1-125-777-11
1-100-786-91
1-100-567-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
0.1uF
560PF
0.1uF
22uF
0.01uF
10%
5%
10%
20%
10%
10V
50V
10V
6.3V
25V
C6040
C6041
C6042
C6043
* C6044
1-100-567-81
1-100-567-81
1-112-717-91
1-112-717-91
1-112-746-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
1uF
1uF
4.7uF
10%
10%
10%
10%
10%
25V
25V
6.3V
6.3V
6.3V
* C6045
C6046
1-112-746-11 CERAMIC CHIP
1-125-777-11 CERAMIC CHIP
4.7uF
0.1uF
10%
10%
6.3V
10V
1-816-654-51
1-817-913-41
1-821-196-11
1-821-196-11
1-817-543-71
FFC/FPC CONNECTOR (LIF) 6P
MEMORY STICK DUO CONNECTOR
CONNECTOR, FPC (ZIF) 39P
CONNECTOR, FPC (ZIF) 39P
CONNECTOR, FPC (ZIF) 27P
< DIODE >
D4002
* D6005
Description
6-550-239-01 TRANSISTOR
8-729-054-48 TRANSISTOR
8-729-054-48 TRANSISTOR
DTA144EMFS6T2L
UP04601008S0
UP04601008S0
< RESISTOR >
< CONNECTOR >
* CN4003
CN4004
* CN4005
* CN4006
* CN6007
Part No.
6-501-216-01 DIODE CL-271HR-C-TS (MS ACCESS)
6-501-955-01 DIODE MAZS056G08S0
R4001
R4002
R4003
R4004
R4005
1-218-990-81
1-218-942-11
1-218-942-11
1-218-942-11
1-218-942-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
120
120
120
120
R4006
R4007
R4008
R6039
R6041
1-218-990-81
1-218-990-81
1-218-949-11
1-218-990-81
1-218-977-11
SHORT CHIP
SHORT CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
0
0
470
0
100K
R6042
R6043
R6045
R6061
R6062
1-218-981-91
1-218-978-11
1-218-989-11
1-218-975-11
1-218-990-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
R6064
R6065
R6066
R6067
R6068
1-208-934-11
1-208-911-11
1-218-990-81
1-218-965-11
1-218-990-81
R6069
R6070
R6071
R6072
R6083
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
5%
1/16W
5%
1/16W
220K
120K
1M
68K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
METAL CHIP
METAL CHIP
SHORT CHIP
RES-CHIP
SHORT CHIP
91K
10K
0
10K
0
0.5%
0.5%
1/16W
1/16W
5%
1/16W
1-218-990-81
1-218-990-81
1-218-990-81
1-218-990-81
1-208-691-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
0
0
0
2.2K
0.5%
1/16W
R6084
R6085
R6086
R6087
R6088
1-208-695-11
1-218-969-11
1-208-643-11
1-218-961-11
1-218-969-11
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
3.3K
22K
22
4.7K
22K
0.5%
5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R6089
R6090
1-218-967-11 RES-CHIP
1-218-968-11 RES-CHIP
15K
18K
5%
5%
1/16W
1/16W
< FERRITE BEAD >
< SWITCH >
FB4001
FB4002
FB4003
FB4004
1-469-580-21
1-469-580-21
1-469-580-21
1-469-580-21
INDUCTOR, FERRITE BEAD (1005)
INDUCTOR, FERRITE BEAD (1005)
INDUCTOR, FERRITE BEAD (1005)
INDUCTOR, FERRITE BEAD (1005)
< IC >
IC6001
S4001
< VARISTOR >
* VDR401 1-802-279-11 VARISTOR (SMD)
8-753-229-95 IC CXM3006CER-T4
Electrical parts list of the SE-174 board is
not shown.
Page 5-18 is not shown.
< COIL >
L6001
L6002
L6003
1-400-588-11 INDUCTOR
1-400-588-11 INDUCTOR
1-400-588-11 INDUCTOR
10uH
10uH
10uH
< TRANSISTOR >
Q6001
Q6002
Q6010
Q6011
* Q6013
1-771-138-21 SWITCH, KEY BOARD (POWER)
8-729-427-37
8-729-427-67
6-550-601-01
6-551-184-01
6-551-157-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
XP411F-TXE
XP421F-TXE
UNRF2A300AS0
MCH6305-TL-E-S
2SA207900AS0
HDR-TG1/TG1E/TG3E_L2
5-17
ST-186
Ref. No.
Part No.
Description
Ref. No.
A-1528-450-A ST-186 BOARD, COMPLETE
**********************
< CAPACITOR >
C5002
C5003
C5004
C5005
C7501
1-125-777-11
1-165-884-11
1-165-875-11
1-163-001-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
2.2uF
10uF
220PF
0.1uF
10%
10%
10%
10%
10%
10V
6.3V
10V
50V
10V
< CONNECTOR >
*
*
*
*
CN7501
CN7503
CN7504
CN7505
1-821-857-51
1-820-031-51
1-816-644-51
1-816-655-51
CONNECTOR, FPC (LIF (NON-ZIF))
CONNECTOR, FPC (LIF (NON-ZIF))
FFC/FPC CONNECTOR (LIF) 12P
FFC/FPC CONNECTOR (LIF) 8P
< DIODE >
D5002
0 D5003
6-500-619-01 DIODE RB520S-40TE61
6-501-096-01 DIODE CRF02 (TE85R)
< IC >
0 IC5001
6-707-554-01 IC TPS65552DGQR
< COIL >
L5001
1-412-027-11 INDUCTOR
2.2uH
< TRANSISTOR >
0* Q5001 6-551-937-01 TRANSISTOR
TIG032TS-S-TL-E
< RESISTOR >
R5002
R5003
R5004
R5005
R5008
1-216-864-11
1-208-947-11
1-208-935-11
1-218-990-81
1-216-065-91
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
RES-CHIP
R5010
R5011
R7501
1-216-809-11 METAL CHIP
1-218-989-11 RES-CHIP
1-216-295-91 SHORT CHIP
0
330K
100K
0
4.7K
100
1M
0
0.5%
0.5%
1/16W
1/16W
5%
1/10W
5%
5%
1/10W
1/16W
< TRANSFORMER >
0 T5001
1-443-568-31 TRANSFORMER, D.C.-D.C.CONVERTER
Electrical parts list of the VC-522 board is
not shown.
Pages 5-20 to 5-23 are not shown.
• Refer to page 5-1 for mark 0.
HDR-TG1/TG1E/TG3E_L2
5-19
Part No.
Description
• EXCEPT J MODEL
to J MODEL
Checking supplied accessories.
Note: This item is supplied with the unit as an accessory, but is
not prepared as a service part.
"Memory Stick PRO Duo" 4GB
(Note)
AC Adaptor
(AC-L200/L200B)
0 1-479-285-21
DVD-ROM
“ENJOY HANDYCAM”
3-282-264-01 (KR)
ENGLISH/KOREAN/JAPANESE
3-282-264-11 (US, CND)
ENGLISH/FRENCH/SPANISH/PORTUGUESE
3-282-264-21 (UK, NE)
ENGLISH/RUSSIAN/GERMAN/TURKISH
3-282-264-51 (AEP)
ENGLISH/FRENCH/GERMAN/DUTCH/SPANISH/
PORTUGUESE/ITALIAN/TURKISH
3-282-264-61 (E, HK, AUS, CH)
ENGLISH/FRENCH/SIMPLIFIED CHINESE for CHINA/
TRADITIONAL CHINESE for HONG KONG
3-282-264-71 (E)
ENGLISH/TRADITIONAL CHINESE for TAIWAN/
SPANISH/PORTUGUESE
Conversion (2P) Adaptor
Power Cord
0 1-569-007-12
0 1-555-074-91 (AUS)
(E: NTSC, JE)
0 1-790-107-61 (US, CND)
0 1-792-549-41 (JE)
0 1-824-910-71 (AEP, NE, E: PAL)
0 1-827-269-12 (UK, HK)
0 1-832-121-31 (CH)
21-pin Adaptor
0 1-833-892-21 (KR)
1-770-783-21
0 1-834-852-11 (E: NTSC)
(AEP, UK, NE)
Handycam Station
(DCRA-C230)
1-821-803-11
Component A/V Cable
1-834-647-11
A/V Connecting Cable
1-823-156-51
USB Cable (Long)
1-829-868-31
USB Cable (Short)
(not supplied)
USB Adaptor Cap
(not supplied)
Dedicated USB Terminal Adaptor
(not supplied)
USB Adaptor Assy
A-1539-779-A
Wrist Strap
3-299-909-01
Rechargeable Battery Pack
NP-FH50
(Note)
• Refer to page 5-1 for mark 0.
HDR-TG1/TG1E/TG3E_L2
5-24
CD-ROM
“Handycam Application Software”
(“Picture Motion Browser (Software)”/
“PMB Guide”/
“Handycam Handbook (PDF)”)
3-288-517-02
Handycam Handbook (PDF)
The CD-ROM supplied contains all of language version of
the Handycam Handbook (PDF) for printing.
・ The printed matter is not supplied. If required, please
order it with the part number below.
・ (Only for destination Japanese model)
日本国内については日本語のみが印刷での部品供給
可能です。
HDR-TG1
∗ 3-288-518-01
∗ 3-288-518-11
∗ 3-288-518-21
∗ 3-288-518-31
∗ 3-288-518-41
∗ 3-288-518-51
∗ 3-288-518-61
(JAPANESE)
(ENGLISH)
(FRENCH)
(SPANISH)
(PORTUGUESE)
(TRADITIONAL CHINESE)
(KOREAN)
Operating Guide
HDR-TG1
3-288-522-11 (ENGLISH, SPANISH) (US, CND, E, JE)
3-288-522-21 (FRENCH) (CND)
3-288-522-31 (PORTUGUESE) (JE)
3-288-522-41 (TRADITIONAL CHINESE) (E)
3-288-522-51 (KOREAN) (KR, JE)
HDR-TG1E/TG3E
3-288-523-11 (ENGLISH) (AEP, UK, E, HK, AUS, JE)
3-288-523-21 (FRENCH, DUTCH, GREEK) (AEP)
3-288-523-31 (GERMAN, ITALIAN, TURKISH) (AEP)
3-288-523-41 (SPANISH, PORTUGUESE, POLISH) (AEP)
3-288-523-51 (CZECH, HUNGARIAN, SLOVAK) (AEP)
3-288-523-61 (RUSSIAN, UKRAINIAN) (NE, JE)
3-288-523-71 (SWEDISH, DANISH, FINNISH) (NE)
3-288-523-81 (SIMPLIFIED CHINESE) (E, CH, JE)
3-288-523-91 (ARABIC, PERSIAN) (E)
3-288-524-41 (TRADITIONAL CHINESE) (HK)
HDR-TG1/TG1E/TG3E_L2
5-25
HDR-TG1E/TG3E
∗ 3-288-519-11 (ENGLISH)
∗ 3-288-519-21 (FRENCH)
∗ 3-288-519-31 (DUTCH)
∗ 3-288-519-41 (GREEK)
∗ 3-288-519-51 (GERMAN)
∗ 3-288-519-61 (ITALIAN)
∗ 3-288-519-71 (TURKISH)
∗ 3-288-519-81 (SPANISH)
∗ 3-288-519-91 (PORTUGUESE)
∗ 3-288-520-11 (POLISH)
∗ 3-288-520-21 (CZECH)
∗ 3-288-520-31 (HUNGARIAN)
∗ 3-288-520-41 (SLOVAK)
∗ 3-288-520-51 (RUSSIAN)
∗ 3-288-520-61 (UKRAINIAN)
∗ 3-288-520-71 (SWEDISH)
∗ 3-288-520-81 (DANISH)
∗ 3-288-520-91 (FINNISH)
∗ 3-288-521-11 (SIMPLIFIED CHINESE)
∗ 3-288-521-21 (ARABIC)
∗ 3-288-521-31 (PERSIAN)
∗ 3-288-521-41 (MALAY)
∗ 3-288-521-51 (THAI)
∗ 3-288-521-61 (INDONESIAN)
∗ 3-288-521-71 (TRADITIONAL CHINESE)
• J MODEL
付属品
Note：当商品はアクセサリーとして同梱されておりますが
サービス用補修部品としては準備しておりません。
"メモリースティックPROデュオ"
8GB
(Note)
ACアダプター
(AC-L200/L200B)
0 1-479-285-21
電源コード
0 1-792-549-41
ハンディカムステーション
(DCRA-C230)
1-821-803-11
D端子A/Vケーブル
1-834-646-21
A/V接続ケーブル
1-823-156-51
リチャージャブルバッテリーパック
NP-FH50
(Note)
USBケーブル（長）
1-829-868-31
USBケーブル（短）
(供給せず)
専用USB端子アダプター
(供給せず)
USBアダプターキャップ
(供給せず)
USBアダプタ組立
A-1539-779-A
リストストラップ
3-299-909-01
取扱説明書
3-288-522-01 (日本語)
CD-ROM
「Handycam Application Software」
（「Picture Motion Browser」（ソフトウェア）
/
「PMBガイド」/
「ハンディカムハンドブック」
（PDF）
）
3-288-517-02
ハンディカムハンドブック (PDF)
印刷用のハンディカムハンドブック（PDF）は
全ての言語が付属品のCD-ROMに含まれています。
・印刷物は付属されておりません。
必要な場合は下記部品番号にて注文となります。
∗ 3-288-518-01 (日本語)
• 0マークについては，5-1ページを参照して下さい。
HDR-TG1/TG1E/TG3E_L2
5-26E
DVD-ROM
「エンジョイハンディーカム」
3-282-264-01
英語/韓国語/日本語
HDR-TG1/TG1E/TG3E
LEVEL
2
US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
SERVICE MANUAL
Ver. 1.1 2008.08
SUPPLEMENT-1
File this supplement with the service manual.
(DI08-212)
• Change of Repair Parts
& : Points added portion.
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
Page
Former
New
+
318
SP901
#14
SP901
#14
5-8
309
309
Ref. No.
Part No.
Description
Ref. No.
Part No.
* 318
4-111-090-01 SHEET SP
HDR-TG1/TG1E/TG3E_L2
9-852-295-81
Sony EMCS Co.
Description
2008H0500-1
© 2008.8
Published by Kohda TEC
HDR-TG1/TG1E/TG3E
LEVEL
2
US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
SERVICE MANUAL
Ver. 1.3 2009.06
SUPPLEMENT-2
File this supplement with the service manual.
(09-062)
• Change of Repair Parts
: Points changed portion.
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
MS-396 BOARD (2/2) (CONNECTOR)
(Service manual page 4-32, Location F-6 to G-7)
Former
2
REG_GND
HDR-TG1/TG1E/TG3E_L2
9-852-295-82
4
VDR401
XX
REG_GND
1
2
XPOWER_SW
3
4
S4001
POWER
1
S4001
POWER
3
VDR401
XPOWER_SW
New
Sony EMCS Co.
2009F0500-1
© 2009.6
Published by Kohda TEC
& : Points added portion.
: Points changed portion.
ST-186 BOARD (2/2) (CONNECTOR)
(Service manual page 4-37, Location B-2 to B-3)
Former
New
CN7503
14p
14p
CN7503
ST_UNREG
1
ST_UNREG
1
ST_UNREG
2
ST_UNREG
2
ST_UNREG
3
ST_UNREG
3
MT_5.0V
4
MT_5.0V
4
MT_5.0V
5
MT_5.0V
5
ST_GND
ST_UNREG
R7501 0
MT_5.0V
C7501
0.1u
B
10V
6
ST_GND
7
ST_GND
8
ST_GND
9
ST_GND
ST_GND
ST_UNREG
R7501 0
MT_5.0V
C7501
XX
6
ST_GND
7
ST_GND
8
ST_GND
9
ST_GND
N.C.
10
N.C.
10
N.C.
11
N.C.
11
N.C.
12
N.C.
12
N.C.
13
N.C.
13
N.C.
14
N.C.
16
15
14
16
15
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
Page
Former
New
_60
5-3
#3
#3
6
-39
MS
MS
-39
6
55
Ref. No.
Part No.
55
Description
Ref. No.
Part No.
* 60
3-300-053-01 SHEET, CAPACITOR
Description
5-2. ELECTRICAL PARTS LIST
Page
Former
Ref. No.
Part No.
New
Description
Ref. No.
Description
MS-396 Board
MS-396 Board
5-17
Part No.
< VARISTOR >
< VARISTOR >
* VDR401 1-802-279-11 VARISTOR (SMD)
ST-186 Board
ST-186 Board
< CAPACITOR >
5-19
C7501 1-125-777-11 CERAMIC CHIP 0.1uF
< CAPACITOR >
10%
10V
HDR-TG1/TG1E/TG3E_L2
—2—
HARDWARE LIST (1/7)
#1: M1.7 X 2.5
(Black)
2-635-562-11
#2: M1.7 X 4.0
(Black)
2-635-562-31
#3: M1.7 X 2.5
(Red)
2-660-401-01
1.7
2.5
1.7
4.0
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
1.7
4.0
#13: M1.7 X 2.5 (Tapping)
(Silver)
3-085-397-01
1.7
1.7
2.5
#16: M1.4 X 2.5
(Silver)
2-586-337-01
2.5
#19: M1.2 X 4.0 (Tapping)
(Red)
3-086-156-21
1.4
1.5
2.5
1.4
1.4
1.5
#18: M1.4 X 2.5
(Silver)
2-635-591-21
1.7 2.2
1.7
5.0
#15: M1.4 X 1.5
(Silver)
3-062-214-01
1.7
#17: M1.7 X 1.5
(Silver)
2-586-389-01
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
4.0
#14: M1.7 X 2.5
(Silver)
2-599-475-11
2.5
3.5
1.6
#10: M1.7 X 4.0
(Silver)
2-599-475-31
1.7
1.7
1.7
5.0
#8: M1.7 X 3.5 (Tapping)
(Silver)
3-078-890-01
1.4
3.5
1.4
2.5
#7: M1.7 X 1.6
(Black)
7-627-552-18
1.7
3.5
1.7
2.5
#6: M1.4 X 1.7
(Silver)
2-598-474-01
#9: M1.7 X 5.0 (Tapping)
(Silver)
3-078-890-21
#4: M1.4 X 2.5 (Tapping)
(Dark Silver)
3-348-998-81
#20: M1.4 X 3.0
(Silver)
2-635-591-31
1.4
1.2
4.0
3.0
HARDWARE LIST (2/7)
#21: M1.4 X 3.0
(Black)
2-662-396-21
#22: M1.7 X 5.0 (Tapping)
(Silver)
3-083-261-01
#23: M1.7 X 4.0 (Tapping)
(Black)
3-080-204-11
1.7
1.4
5.0
3.0
#25: M1.7 X 3.0
(Black)
2-635-562-21
3.0
3.0
#36: M3.0 X 6.0
(Silver)
4-886-821-11
3.0
4.0
6.0
6.0
#38: M3.0 X 20.0 (Tapping)
(Silver)
7-685-651-79
2.0
4.5
#35: M4.0 X 6.0 (Tapping)
(Silver)
3-975-291-02
8.0
#37: M2.0 X 6.0 (Tapping)
(Black)
3-080-206-31
3.0
4.0
#34: M3.0 X 8.0
(Black)
3-077-331-41
6.0
#32: M2.0 X 4.5 (Tapping)
(Silver)
2-102-498-01
1.2
3.5
#33: M3.0 X 6.0
(Silver)
3-077-331-21
4.0
#31: M3.0 X 4.0
(Silver)
2-102-434-01
1.4
1.4
1.4
2.0
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
2.5
#28: M1.4 X 4.0 (Tapping)
(Silver)
3-348-998-61
1.4
2.0
#29: M1.4 X 2.5
(Black)
2-662-396-01
5.5
#27: M1.4 X 2.0
(Black)
2-662-396-11
1.7
1.7
1.7
4.0
#26: M1.4 X 2.0
(Silver)
2-635-591-11
3.0
#24: B1.7 X 5.5 (Tapping)
(Black)
4-679-805-11
#39: M2.6 X 5.0 (Tapping)
(Black)
7-685-791-09
#40: M2.0 X 4.0 (Tapping)
(Silver)
7-685-851-04
3.0
2.0
6.0
2.6
20.0
5.0
2.0
4.0
HARDWARE LIST (3/7)
#41: M3.0 X 8.0 (Tapping)
(Silver)
3-065-748-01
#42: M2.0 X 4.0 (Tapping)
(Silver)
7-628-253-00
#43: M1.7 X 4.0
(Red)
2-660-401-31
3.0
8.0
2.0
#46: M1.7 X 3.0
(Red)
2-660-401-11
1.7
3.0
#49: M2.0 X 4.0
(Black)
2-630-005-31
2.0
4.0
#48: M1.7 X 2.5
(Silver)
3-973-497-91
1.7
1.4
2.5
3.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
1.7
3.0
#47: M1.4 X 3.0 (Tapping)
(Silver)
2-665-774-01
1.4
2.5
1.7
4.0
4.0
#45: M1.4 X 2.5
(Silver)
2-587-151-01
#44: M1.7 X 3.0 (Tapping)
(Silver)
3-078-890-61
#51: M2.0 X 2.5
(Silver)
3-073-686-01
#52: M2.0 X 4.0 (Tapping)
(Black)
3-080-206-11
2.0
2.0
2.0
4.0
3.0
2.5
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
6.0
5.0
#57: M1.7 X 4.0
(Black)
7-627-852-18
#56: M2.0 X 3.5
(Silver)
3-067-187-11
1.75
2.0
2.0
4.0
#58: M2.0 X 6.0 (Tapping)
(Silver)
3-719-408-11
6.0
2.0
3.5
#59: M2.0 X 5.0 (Tapping)
(Silver)
3-080-205-21
2.0
1.7
4.0
#55: M2.0 X 4.0
(Silver)
2-655-582-11
#54: M1.75 X 6.0 (Tapping)
(Black)
3-318-203-11
#60: M2.6 X 5.0
(Black)
3-061-062-11
2.6
2.0
5.0
5.0
HARDWARE LIST (4/7)
#61: M3.0 X 10.0
(Black)
7-682-549-09
#62: M2.0 X 3.0
(Silver)
3-080-202-21
3.0
10.0
2.0
12.5
#66: M1.4 X 1.4
(Silver)
2-635-591-41
1.4
3.5
2.0
4.0
3.5
3.5
#76: M1.7 X 4.0 (Tapping)
(Silver)
2-666-551-11
1.7
4.0
#79: M1.4X 2.0
(Silver)
2-587-151-11
#80: M1.4X 2.0
(Black)
3-279-411-01
1.4
1.4
1.2
2.0
1.7
1.7
#78: M1.4 X 3.5
(Red)
3-208-537-11
1.4
1.4
#75: M1.7 X 3.5 (Tapping)
(Silver)
2-666-551-01
6.0
#77: M1.2 X 5.0 (Tapping)
(Silver)
3-086-156-31
#72: M1.4 X 2.0
(Silver)
4-663-621-41
2.0
#74: M1.7 X 6.0 (Tapping)
(Silver)
2-666-551-31
1.7
4.0
#71: M1.4 X 2.0
(Red)
3-208-537-01
5.0
1.2
5.0
1.4
1.7
1.7
#73: M1.2 X 4.0 (Tapping)
(Black)
3-086-156-61
#68: M1.7 X 4.0
(Silver)
2-655-581-01
1.4
#70: M1.7 X 5.0
(Silver)
2-599-475-41
3.0
5.0
#67: M1.4 X 2.0
(Silver)
3-389-523-16
1.4
#69: M1.7 X 3.0
(Silver)
2-599-475-21
1.7
5.0
3.0
#65: M1.4 X 3.5
(Silver)
2-635-591-01
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
#63: M5.0 X 12.5
(Black)
3-060-811-21
2.0
1.4
2.0
HARDWARE LIST (5/7)
#83: M1.7 X 7.0 (Tapping)
(Black)
3-080-204-41
#82: M1.4 X 1.4
(Silver)
3-272-251-01
#81: M1.7 X 2.5
(Silver)
2-515-756-01
1.4
1.7
2.5
2.5
#90: M1.7 X 3.0
(Silver)
3-271-395-01
#91: M1.7 X 3.0 (Tapping)
(Silver)
2-695-434-11
3.0
#97: M1.4 X 2.5
(Black)
2-662-396-31
1.4
1.4
3.0
2.5
#99: M2.5 X 6.0 (Tapping)
(Silver)
3-776-750-02
3.8
8.0
#96: M1.4 X 2.5
(Silver)
2-587-151-21
8.0
#98: M3.0 X 8.0
(Silver)
3-077-331-01
2.5
3.9
#95: M3.0 X 8.0 (Tapping)
(Black)
7-685-646-79
4.0
3.5
2.0
1.7
1.7
1.7
#92: M2.0 X 3.9
(Black)
3-268-954-01
3.5
#94: M1.7 X 4.0
(Black)
2-515-483-31
1.6
5.9
1.7
2.0
#93: M1.7 X 3.5 (Tapping)
(Silver)
3-254-082-01
1.6
5.3
4.0
5.0
#88: M1.6 X 5.9 (Tapping)
(Silver)
2-689-015-01
1.7
1.7
2.0
3.0
#87: M1.6 X 5.3
(Black)
2-689-328-01
#86: M1.7 X 4.0 (Tapping)
(Silver)
2-695-434-21
#89: M2.0 X 5.5 (Tapping)
(Silver)
2-695-575-01
1.7
7.0
1.4
#85: M1.7 X 2.5
(Black)
2-515-483-11
#84: M2.0 X 3.0
(Silver)
3-072-453-11
#100: M2.0 X 6.0
(Black)
3-080-203-51
2.5
6.0
2.0
6.0
HARDWARE LIST (6/7)
#102: M2.6 X 8.0
(Black)
7-621-284-30
#101: M2.0 X 5.0
(Silver)
7-621-555-39
2.6
2.0
5.0
#105: M2.0 X 4.0
(Red)
2-891-494-31
10.0
#106: M2.0 X 6.0
(Black)
3-713-786-11
#107: M2.0 X 5.0
(Silver)
3-032-750-01
2.0
4.0
6.0
#109: M1.7 X 3.0
(Black)
2-515-483-21
#110: M2.0 X 3.0
(Black)
2-630-005-21
5.0
#117: M1.7 X 4.5 (Tapping)
(Silver)
2-695-429-31
#115: M1.4 X 3.5 (Tapping)
(Silver)
3-348-998-51
1.4
#116: M2.0 X 3.5 (Tapping)
(Silver)
2-695-435-01
2.0
1.4
3.5
#119: M2.6 X 5.0
(Black)
7-627-556-58
1.4
2.0
#112: M1.4 X 5.0
(Black)
2-178-410-11
5.0
3.5
#118: M1.4 X 2.0
(Black)
2-655-580-01
1.7
3.0
4.0
5.5
1.7
1.7
2.0
1.7
#108: M1.7 X 3.0 (Tapping)
(Black)
2-695-430-01
#111: M1.7 X 4.0 (Tapping)
(Black)
2-887-124-01
#114: M2.0 X 5.5 (Tapping)
(Silver)
2-698-464-01
#113: M1.7 X 5.0
(Black)
2-635-562-41
8.0
5.0
3.0
3.0
3.0
2.0
2.0
1.7
#104: M3.0 X 8.0
(Black)
7-682-548-09
2.6
8.0
2.0
4.5
#103: M2.6 X 10.0
(Silver)
7-685-794-09
#120: M2.6 X 6.0
(Silver)
7-621-770-67
2.6
2.6
5.0
6.0
HARDWARE LIST (7/7)
#121: M2.0 X 4.0 (Tapping)
(Silver)
3-080-205-11
#122: M3.0 X 6.0
(Black)
7-682-547-09
#123: M4.0 X 8.0
(Black)
7-682-561-09
3.0
2.0
6.0
4.0
1.4
2.9 4.0
3.0
25.0
#130: M2.0 X 4.5 (Tapping)
(Silver)
3-732-817-11
3.0
12.0
#131: M4.0 X 12.0
(Silver)
3-452-471-01
3.0
4.0
2.6
6.0
#136: M1.4 X 4.0 (Tapping)
(Black)
3-065-509-11
#135: M2.0 X 2.5
(Black)
7-627-553-28
2.6
7.0
#132: M2.6 X 6.0
(Black)
4-673-655-01
12.0
#134: M2.6 X 7.0
(Black)
3-299-572-01
4.0
12.0
2.0
4.5
#133: M3.0 X 6.0
(Black)
3-452-484-01
6.0
#128: M4.0 X 12.0
(Black)
3-452-472-01
6.0
#129: M3.0 X 12.0
(Black)
7-682-550-09
1.7
2.0
#127: M3.0 X 25.0
(Black)
7-682-654-09
3.5
3.0
4.0
8.0
#126: M2.9 X 3.5
(Black)
3-292-616-01
#125: M1.4 X 3.0
(Black)
3-291-847-01
#124: M1.7 X 2.0
(Silver)
2-599-475-01
1.4
2.0
2.5
4.0
Reverse
985229534.pdf
Revision History
∗: S.M. revised only top cover.
Date
1.0
2008.03
Official Release
1.1
2008.08
Supplement-1
(S1 DI08-212)
• Change of Repair Parts
No
1.2
2008.09
2009.06
• Change of Repair Parts
S.M. revised: Page 5-6
• Change of Repair Parts
Yes
1.3
Revised-1
(A1 DI08-259)
Supplement-2
(S2 09-062)
HDR-TG1/TG1E/TG3E_L2
History
Contents
S.M. Rev.
issued
—
Ver.
—
Yes∗

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Top types

Top brands

Download SERVICE MANUAL - EXIT EQUIPMENT