Download INSTALLATION INSTRUCTIONS 88029

Transcript
PARTS LIST
P/N
130019
170081
170082
176083
176084
176085
176086
176088
176089
176080
420027
602612
602615
615
616
7727
860072
420026
860086
170078
860155
420088
545
860157
420086
520086
DESCRIPTION
Rear Track Bar Bracket
Right Brake Hose
Left Brake Hose
End Link Center
End Link Bottom
End Link Bracket
Track Bar
Rear End Link
Front Bump Stop Perch
Suspension Link
Rear Bump Stop Spacer
Track bar End (ball joint)
End Link Swivel
Front Coil Spring (6506 only)
Rear Coil Spring (6506 only)
Pitman Arm
Rear Track Bar Relocation Kit
Sleeve
7/16-14x1.0 HHCS
7/16-14 Stover Nut
7/16 SAE Washer
M12-1.75x70 HHCS
M12-1.75 Nut
SAE Washer
3/8-16x1.0 HHCS
3/8-16 Stover Nut
3/8 SAE Washer
Gasket Kit
Brake Line Gasket
Rear End Link Hardware Kit
Sleeve, Rear End Link
Bushing
7/16-20x2.5 HHCS
7/16-20 Stover Nut
7/16 SAE Washer
7/16 USS Washer
Front Track Bar Hardware Kit
Sleeve
Bushing
3/8-16x1.5 HHTS
3/4-16 Jam Nut
Cotter Pin
QTY.
1
1
1
2
2
2
1
2
2
4
2
1
2
2
2
1
1
1
1
1
2
2
2
4
1
1
2
1
4
1
4
4
4
4
4
6
1
1
2
2
1
1
P/N
860160
176090
860161
176091
860218
420080
520080
860070
860483
860561
420084
545
770057
94180
780281
88056
94119
94177
694
698
615
616
DESCRIPTION
Shift Relocation Kit
Bracket
1/4-20x.75 BHCS
1/4 SAE Washer
1/4-20 Nylock Nut
Thread Lock
Skid Plate Spacer Kit
Skid Plate Spacer
1/2 Cone Washer
1/2-13x2.5 FSHCS
M10-1.50x70 HHCS
10mm Lock Washer
Articulation Bushing Kit
Sleeve
Bushing
Shim Kit
Shim
Skid Plate Hardware Kit
M12-1.75 x 65 HHCS
12mm Washer
Quick Disconnect Hardware Kit
Sleeve, Front End Link
Bushing
Lynch Pin Assembly
3/4 Rubber Washer
10mm Washer
1/2-20 x 1.75 HHCS
1/2-20 x 2.75 HHCS
1/2-20 Nylock Nut
1/2 SAE Washer
1/2 USS Washer
Information Pack
Rancho Decal
Instructions
Consumer/Warranty Information
Warning Sticker
Included in RS6504 only
Front Spring
Rear Spring
Included in RS6505 only
Front Spring
Rear Spring
QTY.
1
1
4
4
4
2
1
6
6
6
2
2
1
8
16
1
16
1
6
6
1
2
2
2
4
2
2
2
4
4
4
1
1
1
1
1
2
2
2
2
RANCHO LINK ASSEMBLY
520080
BUSHING & SLEEVE INSTALLATION
420080
1)  Lubricate the outside diameter of two urethane
bushings (part No. 520080) with a silicone spray or a mild
solution of soap and water.
2)  Press the lubricated bushings into one end of a new
Rancho suspension link (176080) as shown in figure 1.
176080
3)  Lubricate the outside diameter of sleeve 420080
and the inside diameter of the installed urethane bushings
with synthetic grease. Refer to Important Note P. Press the
sleeve into the bushings.
Figure 1
NOTE: It may be necessary to use a bench vise or C-clamp
to press the bushings and sleeves into the cast links. Do not
use a hammer.
3