1
Download HTST7 Service Manual
Transcript
HT-ST7 SA-ST7 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Australian Model Ver. 1.0 2013.06 • All of the units included in the HT-ST7 (SAST7/SA-WST7/EZW-RT50) are required to confirming operation of SA-ST7. Check in advance that you have all of the units. COMPONENT MODEL NAME HT-ST7 Sound Bar (Active Speaker System) SA-ST7 Subwoofer (Active Subwoofer) SA-WST7 Wireless transceiver EZW-RT50 • Please refer to service manual separately issued for Subwoofer. As for EZW-RT50, the part number has been described to this service manual. SPECIFICATIONS Amplifier section BLUETOOTH section Center speaker block Wireless transceiver (EZW-RT50) U.S. models: POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (FTC) Front L + Front R: With 4 ohms loads, both channels driven, from 200 - 20,000 Hz; rated 25 Watts per channel minimum RMS power, with no more than 1% total harmonic distortion from 250 milliwatts to rated output. POWER OUTPUT (reference) Front L/Front R speaker blocks: 50 Watts (per channel at 4 ohms, 1 kHz) Center speaker block: 50 Watts (per channel at 4 ohms, 1 kHz) Communication system BLUETOOTH Specification version 3.0 Output BLUETOOTH Specification Power Class 2 Maximum communication range Line of sight approx. 10 m (33 ft)1) Maximum number of devices to be registered 9 devices Frequency band 2.4 GHz band (2.4000 GHz - 2.4835 GHz) Modulation method FHSS (Freq Hopping Spread Spectrum) Compatible BLUETOOTH profiles2) A2DP (Advanced Audio Distribution Profile) AVRCP 1.3 (Audio Video Remote Control Profile) Supported Codecs3) SBC4) , AAC5), aptX Transmission range (A2DP) 20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz) 1) The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone, reception sensitivity, operating system, software application, etc. 2) BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices. 3) Codec: Audio signal compression and conversion format 4) Subband Codec 5) Advanced Audio Coding Speaker system Full range speaker system, Acoustic suspension Speaker (5 speakers) 65 mm (2 5/8 in) cone type, Magnetic fluid speaker Rated impedance 4 ohms Communication System Wireless Sound Specification version 1.0 Frequency band 5.736 GHz - 5.814 GHz (US and Canadian models) 5.725 GHz - 5.875 GHz (AEP, UK and Australian models) Power requirements DC 3.3 V, 300 mA Modulation method DSSS Dimensions (approx.) 30 mm × 9 mm × 60 mm (1 3/16 in × 3/8 in × 2 3/8 in) (w/h/d) Mass (approx.) 10 g (3/8 oz) Canadian models: POWER OUTPUT (rated) Front L + Front R: 35 W + 35 W (at 4 ohms, 1 kHz, 1 % THD) POWER OUTPUT (reference) Front L/Front R speaker blocks: 50 Watts (per channel at 4 ohms, 1 kHz) Center speaker block: 50 Watts (per channel at 4 ohms, 1 kHz) AEP, UK and Australian models: POWER OUTPUT (rated) Front L + Front R: 40 W + 40 W (at 4 ohms, 1 kHz, 1 % THD) POWER OUTPUT (reference) Front L/Front R speaker blocks: 50 Watts (per channel at 4 ohms, 1 kHz) Center speaker block: 50 Watts (per channel at 4 ohms, 1 kHz) Inputs HDMI IN 1/2/3* OPTICAL IN 1(TV)/2 ANALOG IN COAXIAL IN * These 3 jacks are identical. Using any of them makes no difference. Output HDMI TV OUT (ARC) General Power requirements 120 V AC, 60 Hz (US and Canadian models) 220 V - 240 V AC, 50 Hz/60 Hz (AEP, UK and Australian models) Power consumption On: 50 W (US and Canadian models) On: 55 W (AEP, UK and Australian models) “Control for HDMI” is off (Standby mode): 0.5 W or less BLUETOOTH Standby mode: 0.5 W or less Dimensions (approx.) (w/h/d) 1,080 mm × 109 mm × 110 mm (42 5/8 in × 4 3/8 in × 4 3/8 in) (without grille frame, without stands) 1,080 mm × 109 mm × 129 mm (42 5/8 in × 4 3/8 in × 5 1/8 in) (with grille frame, without stands) 1,080 mm × 129 mm × 138 mm (42 5/8 in × 5 1/8 in × 5 1/2 in) (with grille frame, with stands) 1,080 mm × 129 mm × 130 mm (42 5/8 in × 5 1/8 in × 5 1/8 in) (without grille fr am e, with stands) Mass (approx.) 7.9 kg (17 Ib 6 5/8 oz) (with grille frame, with stands) Digital audio input formats supported by the system Dolby Digital Dolby Digital Plus* Dolby TrueHD* DTS DTS 96/24 DTS-HD Master Audio* DTS-HD High Resolution Audio* DTS-HD Low Bit Rate* Linear PCM 2ch 48 kHz or less Linear PCM Maximum 7.1ch 192 kHz or less* * It is possible to input these formats only with HDMI connection. – Continued on next page – Front L/Front R speaker blocks Speaker system 2-way speaker system, Acoustic suspension Speaker Woofer: 65 mm (2 5/8 in) cone type, Magnetic fluid speaker Tweeter; 20 mm (13/16 in) dome type Rated impedance 4 ohms HT-ST7 HOME THEATRE SYSTEM SA-ST7 ACTIVE SPEAKER SYSTEM 9-893-769-01 2013F33-1 © 2013.06 Sony Corporation Published by Sony Techno Create Corporation HT-ST7 Video formats supported by the system Input/Output (HDMI Repeater block) 3D File 2D Frame packing Side-bySide (Half) Over-Under (Top-andBottom) NOTES ON CHIP COMPONENT REPLACEMENT • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. 4096 × 2160p @ 23.98/24 Hz 3840 × 2160p @ 29.97/30 Hz 3840 × 2160p @ 25 Hz 3840 × 2160p @ 23.98/24 Hz 1920 × 1080p @ 59.94/60 Hz 1920 × 1080p @ 50 Hz 1920 × 1080p @ 29.97/30 Hz 1920 × 1080p @ 25 Hz 1920 × 1080p @ 23.98/24 Hz 1920 × 1080i @ 59.94/60 Hz 1920 × 1080i @ 50 Hz 1280 × 720p @ 59.94/60 Hz SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. 1280 × 720p @ 50 Hz 1280 × 720p @ 29.97/30 Hz 1280 × 720p @ 23.98/24 Hz 720 × 480p @ 59.94/60 Hz 720 × 576p @ 50 Hz 640 × 480p @ 59.94/60 Hz Accesseries Grille frame (1) Remote control (1) R03 (size AAA) batteries (2) Digital optical cable for a TV (1) IR blaster (1) Stands (2) and screws (2) Wireless transceivers (2) Operating Instructions (1) Reference Guide (1) Design and specifications are subject to change without notice Standby power consumption: 0.5 W or less (Bar Speaker), 0.5 W or less (Subwoofer) Over 85% power efficiency of amplifier block is achieved with the full digital amplifier, S-Master. Copyrights This system incorporates Dolby* Digital and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, and the double-D symbol are trademarks of Dolby Laboratories. ** Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved. The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. This system incorporates High-Definition Multimedia Interface (HDMI™) technology. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. “BRAVIA” logo is a trademark of Sony Corporation. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 0.15 μF 1.5 kΩ AC voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. “x.v.Color” and “x.v.Color” logo are trademarks of Sony Corporation. The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Android is a trademark of Google Inc. © 2012 CSR plc and its group companies. The aptX® mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. Other trademarks and trade names arethose of their respective owners. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. 2 HT-ST7 TABLE OF CONTENTS 1. SERVICING NOTES ............................................. 4 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. 2-8. 2-9. 2-10. 2-11. 2-12. 2-13. 2-14. 2-15. 2-16. 2-17. 2-18. 2-19. 2-20. 2-21. 2-22. 2-23. 2-24. 2-25. 2-26. 2-27. 2-28. 2-29. Disassembly Flow ........................................................... Panel (L/R) Assy ............................................................. Panel (Rear L) Block, Panel (Rear R)............................. Bracket (Arm A/B) Assy, Fuse (F502)............................ Bracket (Air) Assy .......................................................... Bracket (Bottom) Block .................................................. Power Cord (AC1) .......................................................... Chassis Block .................................................................. POWER Board ................................................................ AMP Board ..................................................................... IO Board ......................................................................... MAIN Board ................................................................... Center Speaker Block ..................................................... Loudspeaker (6.5 cm) (SP5, SP6, SP7, SP8, SP9) ......... Cable with Connector (SPC3)......................................... Cable with Connector (SPC4)......................................... RC-S801/A (NFC1) ........................................................ Bluetooth Module (BT1) ................................................ Front Speaker (L) Block ................................................. Loudspeaker (6.5 cm) (SP3) (L-ch) ................................ Loudspeaker (2 cm) (SP1) (L-ch) ................................... Cable with Connector (SPC1) (L-ch) ............................. Front Speaker (R) Block ................................................. DISPLAY Board ............................................................. Loudspeaker (6.5 cm) (SP4) (R-ch) ................................ Loudspeaker (2 cm) (SP2) (R-ch) ................................... Cable with Connector (SPC2) (R-ch) ............................. KEY Board...................................................................... Flexible Flat Cable (14P) (FFC1) ................................... 3. TEST MODE ............................................................ 27 6 7 7 8 8 9 10 11 12 12 13 13 14 15 16 16 17 18 19 19 20 21 22 23 23 24 25 26 26 4. DIAGRAMS 4-1. 4-2. 4-3. 4-4. Block Diagram - HDMI Section -................................... Block Diagram - MAIN Section -................................... Block Diagram - AMP Section - ..................................... Block Diagram - PANEL/POWER SUPPLY Section - ............................ Schematic Diagram - MAIN Board (1/7) - ..................... Schematic Diagram - MAIN Board (2/7) - ..................... Schematic Diagram - MAIN Board (3/7) - ..................... Schematic Diagram - MAIN Board (4/7) - ..................... Schematic Diagram - MAIN Board (5/7) - ..................... Schematic Diagram - MAIN Board (6/7) - ..................... Schematic Diagram - MAIN Board (7/7) - ..................... Printed Wiring Board - MAIN Board - ........................... Printed Wiring Board - AMP Board - ............................. Schematic Diagram - AMP Board (1/2) - ....................... Schematic Diagram - AMP Board (2/2) - ....................... Printed Wiring Board - IO Board - ................................. Schematic Diagram - IO Board - .................................... Printed Wiring Boards - PANEL Section - ..................... Schematic Diagram - PANEL Section - .......................... Printed Wiring Board - POWER Board -........................ Schematic Diagram - POWER Board - .......................... 4-5. 4-6. 4-7. 4-8. 4-9. 4-10. 4-11. 4-12. 4-13. 4-14. 4-15. 4-16. 4-17. 4-18. 4-19. 4-20. 4-21. 30 31 32 33 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 5. EXPLODED VIEWS 5-1. 5-2. 5-3. 5-4. 5-5. 5-6. 5-7. 5-8. 5-9. 5-10. Panel Section................................................................... Bracket (Bottom) Section ............................................... Power Cord Section ........................................................ Chassis Section ............................................................... Front Block Section ........................................................ Front Speaker (L) Section ............................................... Center Speaker Section ................................................... DISPLAY Board Section ................................................ Front Speaker (R) Section............................................... Front Panel Section ......................................................... 6. ELECTRICAL PARTS LIST .............................. 76 66 67 68 69 70 71 72 73 74 75 Accessories are given in the last of the electrical parts list. 3 HT-ST7 SECTION 1 SERVICING NOTES UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. ADVANCE PREPARATION WHEN CONFIRMING OPERATION All of the units included in the HT-ST7 (SA-ST7/SA-WST7/EZWRT50) are required to confirming operation of SA-ST7. Check in advance that you have all of the units. CAPACITOR ELECTRICAL DISCHARGE PROCESSING When checking the board, for the electric shock prevention, connect the resistors to both ends of respective capacitor (C519) to discharge the capacitor (C519). – POWER Board (Conductor Side) – 800 :/2 W C519 ABOUT THE PAIRING METHOD When the following repair is performed, the pairing of the Bar speaker (SA-ST7) and Subwoofer (SA-WST7) is cut. • • Replacing of complete MAIN board Replacing of IC1002 on the MAIN board Return the Bar speaker (SA-ST7) and Subwoofer (SA-WST7) to the customer after performing the pairing according to the following procedure. Preparation: Insert the wireless transceivers (EZW-RT50) into the Bar speaker (SA-ST7) and Subwoofer (SA-WST7). NOTE OF PERFORMING THE OPERATION CHECK IN THE STATE THAT HEAT SINK WAS REMOVED When performing the operation check in the state that this unit was disassembled, it is possible to perform the operation check in the state that heat sink was removed. But don’t perform the operation check in the long time, and perform the operation check in the volume state as low as possible. NOTE OF REPLACING THE IC3506 ON THE MAIN BOARD IC3506 on the MAIN board cannot exchange with single. When this part is damaged, exchange the complete mounted board. NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD When IC3001, IC3003, IC3005 and IC3007 on the AMP board and the complete AMP board are replaced, it is necessary to spread the compound between the AMP board and the heat sink. Spread the compound referring to the figure below. Procedure: 1 Connect the AC power cords (mains leads). 2 Press the button on the Bar Speaker. 3 Confirm the indicator of the subwoofer is lit in green. If not, the wireless transmission is not activated. – AMP Board (Component Side) – thermal compound IC3001 4 IC3003 IC3005 IC3007 No sound is output from the subwoofer. Make sure the AC power cord (mains lead) of the subwoofer is connected. Make sure the wireless transceivers are inserted correctly. If the indicator is off: – Check that the AC power cord (mains lead) of the subwoofer is connected securely. button on the subwoofer. – Turn the subwoofer on by pressing the indicator flashes in green quickly: If the button on the subwoofer, then insert the wieless transceiver First press the into the subwoofer correctly, and press the button on the subwoofer again. If the indicator flashes in red: Press the button to turn off the subwoofer, and check that nothing is blocking the ventilation holes of the subwoofer. HT-ST7 MODEL IDENTIFICATION Distinguish by model number label stuck on the rear side of a main unit. Note: The printed contents of following figure model number label may be different from the model number label of a main unit. MODEL NUMBER LABEL US and Canadian models SA-ST7 UC2 4-461-308-0s UK model 4-461-309-1s Australian model AEP model SA-ST7 AU1 4-466-482-0s 4-461-309-0s – Rear view – 5 HT-ST7 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW Note: When disassembling the unit, start working after removing the grill frame always first. SET 2-2. PANEL (L/R) ASSY (Page 7) 2-3. PANEL (REAR L) BLOCK, PANEL (REAR R) (Page 7) 2-7. POWER CORD (AC1) (Page 10) 2-6. BRACKET (BOTTOM) BLOCK (Page 9) 2-4. BRACKET (ARM A/B) ASSY, FUSE (F502) (Page 8) 2-5. BRACKET (AIR) ASSY (Page 8) 2-8. CHASSIS BLOCK (Page 11) 2-9. POWER BOARD (Page 12) 2-10. AMP BOARD (Page 12) 2-13. CENTER SPEAKER BLOCK (Page 14) 2-14. LOUDSPEAKER (6.5 cm) (SP5, SP6, SP7, SP8, SP9) (Page 15) 2-11. IO BOARD (Page 13) 2-12. MAIN BOARD (Page 13) 2-15. CABLE WITH CONNECTOR (SPC3) (Page 16) 2-17. RC-S801/A (NFC1) (Page 17) 2-23. FRONT SPEAKER (R) BLOCK (Page 22) 2-18. BLUETOOTH MODULE (BT1) (Page 18) 2-24. DISPLAY BOARD (Page 23) 2-19. FRONT SPEAKER (L) BLOCK (Page 19) 2-25. LOUDSPEAKER (6.5 cm) (SP4) (R-ch) (Page 23) 2-20. LOUDSPEAKER (6.5 cm) (SP3) (L-ch) (Page 19) 2-26. LOUDSPEAKER (2 cm) (SP2) (R-ch) (Page 24) 2-21. LOUDSPEAKER (2 cm) (SP1) (L-ch) (Page 20) 2-27. CABLE WITH CONNECTOR (SPC2) (R-ch) (Page 25) 2-22. CABLE WITH CONNECTOR (SPC1) (L-ch) (Page 21) 6 2-16. CABLE WITH CONNECTOR (SPC4) (Page 16) 2-28. KEY BOARD (Page 26) 2-29. FLEXIBLE FLAT CABLE (14P) (FFC1) (Page 26) HT-ST7 Note: Follow the disassembly procedure in the numerical order given. 2-2. PANEL (L/R) ASSY 3 panel (L) assy Note 2: When installing the panel (L/R) assy, check the presence or absence of a mark, do not mistake the right and left. 1 two screws (BVTP3 u 10) 2 two claws Mark on the panel (R) assy 1 two screws (BVTP3 u 10) 3 panel (R) assy Note 1: Please spread a sheet under a unit not to injure front side. 2 two claws 2-3. – Rear bottom view – PANEL (REAR L) BLOCK, PANEL (REAR R) 5 seven screws (step) (BVTP3) 7 two screws (step) (BVTP3) 8 panel (rear R) 5 seven screws (step) (BVTP3) 2 claw 3 foot (corner) 1 two bosses Note 2: When installing the panel, check that J251 installed the position shown in the figure. 6 panel (rear L) block 4 Remove the power cord from the hook of panel (rear L). Note 1: Please spread a sheet under a unit not to injure front side. 3ower ForG VettiQJ J251 – Rear view – 2 claw 1 two bosses 3 foot (corner) – Rear bottom view – power cord – Rear view – 7 HT-ST7 2-4. BRACKET (ARM A/B) ASSY, FUSE (F502) 1 screw (BVTP3 u 8) 4 bracket (arm A) assy 4 bracket (arm B) assy 2 boss 3 claw 1 screw (BVTP3 u 8) 4 bracket (arm B) assy 2 boss 1 screw (BVTP3 u 8) 3 claw 4 bracket (arm A) assy 2 boss 3 claw 1 screw (BVTP3 u 8) 3 claw 2 boss 1 screw (BVTP3 u 8) 5 fuse (F502) 1 screw (BVTP3 u 8) Note: Please spread a sheet under a unit not to injure front side. 1 screw (BVTP3 u 8) 1 screw (BVTP3 u 8) – Rear bottom view – 2-5. BRACKET (AIR) ASSY 2 bracket (air) assy 1 three screws (BVTP3 u 8) 1 three screws (BVTP3 u 8) 2 bracket (air) assy 1 three screws (BVTP3 u 8) 2 bracket (air) assy Note: Please spread a sheet under a unit not to injure front side. – Rear bottom view – 8 HT-ST7 2-6. BRACKET (BOTTOM) BLOCK 3 guide pin 2 three screws (BVTP3 u 8) 4 boss 5 bracket (bottom) block 2 three screws (BVTP3 u 8) 3 guide pin Note: Please spread a sheet under a unit not to injure front side. 1 nine screws (BV/ring) – Rear bottom view – 9 HT-ST7 2-7. POWER CORD (AC1) 2 power cord connector (CN501) 3ower ForG VettiQJ Note 2: When installing the power cord (AC1), check the direction of claw of cord bushing (FBS001) and install correctly. 3 Draw out the power cord. claw cord bushing (FBS001) 1 Remove the power cord from the clamp (L35). power cord (AC1) 150 +5, -0 mm 3ower ForG $& VettiQJ to POWER board clamp (L35) 6 power cord (AC1) 5 cord bushing (FBS001) power cord (AC1) POWER board Note 1: Please spread a sheet under a unit not to injure front side. 4 Remove the cord bushing (FBS001) in the direction of an arrow. – Rear bottom view – 10 HT-ST7 2-8. CHASSIS BLOCK :ire VettiQJ AMP board clamp (L35) 9 flexible flat cable (14P) (CN902) 0 flexible flat cable (5P) (CN1007) 7 flexible flat cable (8P) (CN1002) 8 flexible flat cable (15P) (CN1005) 4 connector (CN3002) 5 connector (CN3003) 6 cushion (QJ, S) )Oe[ibOe IOat FabOe VettiQJ flexible flat cable (8P) flexible flat cable (15P) 3 connector (CN3006) 2 connector (CN3007) 1 Remove wires from the clamp (L35). cushion (QJ, S) MAIN board Note 1: Please spread a sheet under a unit not to injure front side. – Rear bottom view – Note 2: When installing the flexible flat cable, ensure the colored line. No slanting after insertion. colored line flexible flat cable connector qa six screws (BVTP3 u 8) qs chassis block 11 HT-ST7 2-9. POWER BOARD 1 connector (CN3004) 3 four screws (BVTP3 u 8) A 3 three screws (BVTP3 u 8) 3 screw (BVTP3 u 8) 4 clamp (L35) A 2 connector (CN503) 5 POWER board – Rear bottom view – 2-10. AMP BOARD 4 heatsink (AMP) Note: When installing the heat sink, spread the compound referring to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on servicing notes (page 4). 5 screw (BV3 u 8 CU) 3 two screws (transistor) 3 two screws (transistor) 4 heatsink (AMP) Note: When installing the heat sink, spread the compound referring to “NOTE OF 5 two screws REPLACING THE IC3001, IC3003, (BV3 u 8 CU) IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE IC3001 AMP BOARD” on servicing notes (page 4). 5 two screws (BV3 u 8 CU) IC3007 5 screw (BV3 u 8 CU) 5 two screws (BV3 u 8 CU) IC3005 IC3003 6 clamp (L35) 7 AMP board 2 flexible flat cable (28P) (CN3001) 1 connector (CN3004) – Rear bottom view – 12 HT-ST7 2-11. IO BOARD 0 tape (BT) 7 two screws (BVTP3 u 8) 4 screw (BVTP3 u 8) qa IO REINFORCE board block B 9 Remove two bonds. qs IO board 4 screw (BVTP3 u 8) 8 housing (wireless) 6 Remove the IO board block in the direction of an arrow. 3 connector (CN1004) 1 flexible flat cable (9P) (CN201) 5 four screws (BVTP3 u 8) 2 flexible flat cable (13P) (CN4001) B Note 2: When installing the flexible flat cable, ensure the colored line. No slanting after insertion. colored line flexible flat cable connector Note 1: When removing flexible flat cables, do not remove connector on the MAIN board side. – Rear bottom view – 2-12. MAIN BOARD 6 screw (BVTP3 u 8) 6 two screws C (BVTP3 u 8) 1 flexible flat cable (9P) (FFC2) (CN901) 2 flexible flat cable (13P) (FFC4) (CN1001) 6 screw (BVTP3 u 8) 6 two screws (BVTP3 u 8) 6 screw (BVTP3 u 8) 7 four screws (B3 u 6) C 9 MAIN board 3 flexible flat cable (28P) (CN5002) Note 2: When installing the flexible flat cable, ensure the colored line. No slanting after insertion. colored line flexible flat cable connector :LUHVHWWLQJ AMP board 5 connector (CN601) 4 saranet cushion 8 Remove the MAIN board in the direction of an arrow. MAIN board saranet cushion Note 1: When the complete MAIN board is replaced, refer to “ABOUT THE PAIRING METHOD” on page 4. – Rear bottom view – 13 HT-ST7 2-13. CENTER SPEAKER BLOCK 5 screw (PTPWH3 u 8) 3 Remove the cable with connector (SPC3) from three hooks of center speaker block. 2 Remove the cable with connector (SPC4) from three hooks of center speaker block. 7 center speaker block 1 saranet cushion 5 screw (PTPWH3 u 8) guide pin Note 1: When installing the center speaker block, align the guide pin and ditch. 6 three screws (BVP-tite 3 u 8) Note 1: Please spread a sheet under a unit not to injure front side. 4 Remove the cable with connector (SPC2) ditch from three hooks of center speaker block. 4 Remove the cable with connector (SPC1) from three hooks of center speaker block. – Rear bottom view – :LUHVHWWLQJ 1 Install cables with connector (SPC1, SPC2) to the hook of the center speaker block. center speaker block cable with connector (SPC2) cable with connector (SPC1) 2 Install cables with connector (SPC3) to the hook of the center speaker block. cable with connector (SPC3) 3 Install cables with connector (SPC4) to the hook of the center speaker block. cable with connector (SPC4) 14 4 Paste the saranet cushion. HT-ST7 2-14. LOUDSPEAKER (6.5 cm) (SP5, SP6, SP7, SP8, SP9) 1 two screws (3.5) 1 two screws (3.5) 4 loudspeaker (6.5 cm) (SP6) Note 1: Procedure of removal of SP5, SP7, SP8 and SP9 are the same as the SP6. SP5 3 terminal (narrow side) [black] 3 terminal (wide side) [red] SP7 :LUHVHWWLQJ Note 2: When installing the speaker wire, make the position of caulking of terminals is outside. SP9 SP8 narrow side [black] loudspeaker (6.5 cm) –)URQWERWWRPYLHZ– 2 Remove the loudspeaker (6.5 cm) (SP6) in the direction of an arrow. :LUHVHWWLQJ terminals position (wide side) [gray] terminals position (narrow side) [black] wide side [SP5: gray] [SP6: red] [SP7: gray] [SP8: red] [SP9: blue] Note 3: When installing the loudspeaker (6.5 cm) (SP5, SP6, SP7, SP8, SP9), make the position of terminals as shown in the figure below. terminals position (wide side) [gray] terminals position (narrow side) [black] loudspeaker (6.5 cm) (SP5) terminals position (wide side) [blue] terminals position (narrow side) [black] terminals position (wide side) [red] terminals position (narrow side) [black] loudspeaker (6.5 cm) loudspeaker (6.5 cm) (SP7) (SP9) terminals position (wide side) [red] terminals position (narrow side) [black] loudspeaker (6.5 cm) loudspeaker (6.5 cm) (SP8) (SP6) 15 HT-ST7 2-15. CABLE WITH CONNECTOR (SPC3) 1 cushion (absorbent) [black] 1 cushion (absorbent) 2 Remove the cord bushing of cable with connector in the direction of an arrow. [gray] 3 cable with connector (SPC3) [black] –)URQWERWWRPYLHZ– [red] :LUHVHWWLQJ OK cord bush cord bush No gap. 2 Remove the cord bushing of cable with connector in the direction of an arrow. NG There is a gap. cabinet (R) assy cabinet (R) assy cable with connector (SPC3) cable with connector (SPC3) 2-16. CABLE WITH CONNECTOR (SPC4) 1 cushion (absorbent) 1 cushion (absorbent) 1 cushion (absorbent) 2 Remove two cord bushings of cable with connector in the direction of an arrow. [black] [gray] [black] [blue] [black] 3 cable with connector (SPC4) [red] –)URQWERWWRPYLHZ– :LUHVHWWLQJ No gap. 2 Remove the cord bushing of cable with connector in the direction of an arrow. OK NG cord bush cord bush There is a gap. 16 cabinet (R) assy cabinet (R) assy cable with connector (SPC3) cable with connector (SPC3) HT-ST7 2-17. RC-S801/A (NFC1) Note 2: When installing the flexible flat cable, ensure the colored line. No slanting after insertion. colored line )OH[LEOHIODWFDEOH3VHWWLQJ flexible flat cable (8P) flexible flat cable connector saranet cushion saranet cushion –5HDUWRSYLHZ– 1 saranet cushion 1 saranet cushion Note 1: Please spread a sheet under a unit not to injure front side. 2 boss 3 Remove the RC-S801/A block in the direction of an arrow. 5 tape (sub material) 4 two cushions (NFC) 6 flexible flat cable (8P) (FFC5) 5&6$1)&VHWWLQJ 7 RC-S801/A (NFC1) cushion (NFC) RC-S801/A (NFC1) cushion (NFC) flexible flat cable (8P) tape (sub material) –,QVLGHYLHZ– guide boss RC-S801/A (NFC1) guide –5LJKWYLHZ– 17 HT-ST7 2-18. BLUETOOTH MODULE (BT1) Flexible flat cable (14P) setting flexible flat cable tape (sub material) (14P) flexible flat cable Bluetooth module (BT1) (14P) – Right view – tape (sub material) saranet cushion – Rear top view – 3 boss 6 flexible flat cable (14P) 1 saranet cushion Note 2: When installing the flexible flat cable, ensure the colored line. No slanting after insertion. colored line connector Note 1: Please spread a sheet under a unit not to injure front side. 5 tape (sub material) flexible flat cable 4 Remove the Bbluetooth module block in the direction of an arrow. 5 tape (sub material) 2 screw (BVTP2.6) 7 Bluetooth module (BT1) 18 HT-ST7 2-19. FRONT SPEAKER (L) BLOCK 3 front speaker (L) block 1 two screws (PTPWH3 u 8) Note 2: When installing the front speaker (L) block, align the guide pin and ditch. guide pin ditch Note 1: Please spread a sheet under a unit not to injure front side. 2 three screws (BVP-tite 3 u 8) – Rear bottom view – 2-20. LOUDSPEAKER (6.5 cm) (SP3) (L-ch) Note 1: When installing the loudspeaker (18 cm) (SP1), make the position of terminals as shown in the figure below. terminals position (narrow side) [black] 1 two screws (3.5) loudspeaker (6.5 cm) (SP3) 1 two screws (3.5) 4 loudspeaker (6.5 cm) (SP3) terminals position (wide side) [blue] 3 terminal (wide side) [blue] 3 terminal (narrow side) [black] :LUHVHWWLQJ Note 2: When installing the speaker wire, make the position of caulking of terminals is outside. 2 Remove the loudspeaker (6.5 cm) (SP3) in the direction of an arrow. wide side [blue] loudspeaker (6.5 cm) (SP3) narrow side [black] –)URQWERWWRPYLHZ– 19 HT-ST7 2-21. LOUDSPEAKER (2 cm) (SP1) (L-ch) Note 1: When installing the loudspeaker (2 cm) (SP2), match the terminal position with the marking. terminal marking 1 two screws (3.5) 1 two screws (3.5) 1 three screws (3.5) 5 loudspeaker (2 cm) (SP1) loudspeaker (2 cm) (SP1) – Baffle (L) block inner view – 4 screw (3.5) 3 terminal (wide side) [red] :ire VettinJ Note 2: When installing the speaker wire, make the position of caulking of terminals is outside. wide side [red] 4 screw (3.5) 3 terminal (narrow side) [black] 2 Remove the baffle (L) block in the direction of an arrow. narrow side [black] 1 screw (3.5) loudspeaker (2 cm) (SP1) – Front bottom view – :ire VettinJ MOUNTED board speaker wire from MOUNTED board 20 HT-ST7 2-22. CABLE WITH CONNECTOR (SPC1) (L-ch) 1 terminal (narrow side) [black] 1 terminal (wide side) [gray] :LUHVHWWLQJ narrow side [black] wide side [gray] MOUNTED board Note: When installing the cable with connector (SPC1), make the position of caulking of terminals is outside. –)URQWERWWRPYLHZ– :LUHVHWWLQJ 3 cable with connector (SPC1) OK cord bush No gap. cabinet (R) assy cable with connector (SPC2) NG 2 Remove the cord bushing of cable with connector in the direction of an arrow. cord bush There is a gap. cabinet (R) assy cable with connector (SPC2) 21 HT-ST7 2-23. FRONT SPEAKER (R) BLOCK 1 two canoe clips (small) 2 three adhesive sheets 6KHHWMDFNVHWWLQJ 1 two canoe clips (small) Note 2: When installing the front speaker (R) block, align the guide pin and ditch. sheet (jack) 3 sheet (jack) 4 screw (PTPWH3 u 8) guide line 4 screw (PTPWH3 u 8) guide line mountain fold guide pin ditch 6 front speaker (R) block valley fold 5 three screws (BVP-tite 3 u 8) Note 1: Please spread a sheet under a unit not to injure front side. –5HDUERWWRPYLHZ– 22 HT-ST7 2-24. DISPLAY BOARD 2 screw (BVTP3 u 12) 7 holder (LED) assy 3 collar (damper) 8 bushing (damper) 2 screw (BVTP3 u 12) 6 two claws 9 DISPLAY board 2 screw (BVTP3 u 12) 3 collar (damper) 8 bushing (damper) 1 saranet cushion 3 collar (damper) 3 collar (damper) 5 flexible flat cable (15P) (FFC6) (CN801) 8 bushing (damper) 2 screw (BVTP3 u 12) 8 bushing (damper) 4 Remove the DISPLAY board block in the direction of an arrow. Note: When installing the flexible flat cable, ensure the colored line. No slanting after insertion. colored line flexible flat cable – Front bottom view – connector 2-25. LOUDSPEAKER (6.5 cm) (SP4) (R-ch) 1 two screws (3.5) 1 two screws (3.5) Note 1: When installing the loudspeaker (6.5 cm) (SP4), make the position of terminals as shown in the figure below. 4 loudspeaker (6.5 cm) (SP4) terminals position (narrow side) [black] 3 terminal (wide side) [blue] 3 terminal (narrow side) [black] terminals position (wide side) [blue] loudspeaker (6.5 cm) (SP4) :LUHVHWWLQJ Note 2: When installing the speaker wire, make the position of caulking of terminals is outside. 2 Remove the loudspeaker (6.5 cm) (SP4) in the direction of an arrow. –)URQWERWWRPYLHZ– wide side [blue] loudspeaker (6.5 cm) (SP4) narrow side [black] 23 HT-ST7 2-26. LOUDSPEAKER (2 cm) (SP2) (R-ch) 1 three screws (3.5) 1 two screws (3.5) 1 two screws (3.5) 2 Remove the baffle (R) 5 loudspeaker (2 cm) (SP2) block in the direction of an arrow. 4 screw (3.5) Note 1: When installing the loudspeaker (2 cm) (SP2), match the terminal position with the marking. marking terminal 4 screw (3.5) 3 terminal (wide side) [red] loudspeaker (2 cm) (SP2) – Baffle (R) block inner view – 3 terminal (narrow side) [black] :ire VettinJ Note 2: When installing the speaker wire, make the position of caulking of terminals is outside. – Front bottom view – 1 screw (3.5) :ire VettinJ MOUNTED board wide side [red] narrow side [black] loudspeaker (2 cm) (SP2) speaker wire from MOUNTED board 24 HT-ST7 2-27. CABLE WITH CONNECTOR (SPC2) (R-ch) :LUHVHWWLQJ narrow side [black] 1 terminal (narrow side) [black] wide side [red] 1 terminal (wide side) [red] MOUNTED board Note: When installing the cable with connector (SPC2), make the position of caulking of terminals is outside. –)URQWERWWRPYLHZ– :LUHVHWWLQJ OK cord bush No gap. 3 cable with connector (SPC2) cabinet (R) assy cable with connector (SPC2) NG cord bush There is a gap. 2 Remove the cord bushing of cable with connector in the direction of an arrow. cabinet (R) assy cable with connector (SPC2) 25 HT-ST7 2-28. KEY BOARD 3 flexible flat cable (5P) (FFC7) (CN751) Note 2: The flexible flat cable (5P) (FFC7) must be inserted before installing the KEY board to the front panel. 4 KEY board 1 four screws (BVTP2.6) 2 Remove the KEY board block in the direction of an arrow. Note 3: When installing the flexible flat cable, ensure the colored line. No slanting after insertion. colored line Note 1: Please spread a sheet under a unit not to injure front side. flexible flat cable connector – Rear bottom view – 2-29. FLEXIBLE FLAT CABLE (14P) (FFC1) Tape (BT) setting cushion (BT pad) 2 tape (BT) Note: Please spread a sheet under a unit not to injure front side. tape (BT) 1 sheet (BT) 3 flexible flat cable (14P) (FFC1) Flexible flat cable (14P) (FFC1) setting guide line sheet (BT) screw hole 26 flexible flat cable (14P) (FFC1) – Rear bottom view – guide line HT-ST7 SECTION 3 TEST MODE 1. TEST MODES OTHER THAN THE TEST MODE MENU These are executable test mode even if not entering the test mode menu. 1-1. Cold Reset It can initialize various backup information. Procedure: 1. Press the [?/1] button to turn the power on. 2. Press the three buttons of the [INPUT], [VOLUME –] and [?/1] simultaneously. 3. The message “RESET” is displayed on the fluorescent indicator tube, then turn the power off. 2-1. Panel Test Mode It can confirm the lighting of fluorescent indicator tube and LEDs, operation of buttons, display of model name, destination and software version. Procedure: 1. Enter the test mode menu. (Refer to “Setting method of the test mode menu”) 2. In the state of blinking the “PANEL” on the fluorescent indicator tube, press the [INPUT] button. 3. All segments in the fluorescent indicator tube and all LEDs are lighted up. 4. When pressing the [VOLUME +] button, the display on the fluorescent indicator tube repeatedly changes in order from all lighting → pattern 1 (power indicator LED (white color) is lighted up) → pattern 2 (Bluetooth indicator LED (blue color) and [MUTING] LED are lighted up). All ligting 2. TEST MODES IN THE TEST MODE MENU These are the test modes done in the test mode menu. Setting method of the test mode menu: 1. Press the [?/1] button to turn the power on. 2. Press the two buttons of the [INPUT] and [VOLUME +] simultaneously for five seconds. 3. The message “PANEL” blinks on the fluorescent indicator tube and enter the test mode menu. Pattern 1 Pattern 2 Releasing method of the test mode menu: Press the [?/1] button to release the test mode menu. 5. In the state of step 4, press the [VOLUME –] button and “K 0” is displayed on the fluorescent indicator tube. Each time a button is pressed, “K 0” value increases. However, once a button is pressed, it is no longer taken into account. When pressing the all buttons, “OK” and “K 5” are alternately displayed on the fluorescent indicator tube. 27 HT-ST7 6. In the state of step 4, press the [INPUT] button and model name “HT-ST7” is displayed on the fluorescent indicator tube. Each time the [VOLUME +] button is pressed, the display changes from destination → MC (-com) version → SY (system) version → UI version → TA (AMP) version → DS (DSP) version → BT (Bluetooth) version → NF (NFC) version → HD (HDMI) version, → CE (CEC) version → PF (platform) version → WS (wireless sound) version in this order, and returns to the model name display. Releasing method: Press the [?/1] button to release the test mode menu. (When the “K 0” to “K 4” is displayed on the fluorescent indicator tube, press the [?/1] button on the remote commander to release the test mode menu) 2-2. Model Name Display Mode It can display the model name. Procedure: 1. Enter the test mode menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “HT-ST7”. Model name Destination BT version 2-3. Destination Display Mode It can display the destination. MC version NF version SY version HD version UI version CE version Procedure: 1. Enter the test mode menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the destination. (Displayed values in the above figure are example) TA version Destination PF version DS version WS version US, Canadian and Australian models NA AEP and UK models CE2 2-4. MC Version Display Mode It can display the MC (-com) version. (Displayed values in the above figure are example) Destination Display Display US, Canadian and Australian models NA AEP and UK models CE2 7. When [INPUT] button is pressed while the each version is displayed on the fluorescent indicator tube, year, month and day of the software creation is displayed on the fluorescent indicator tube. (Displayed values in the above figure are example) Procedure: 1. Enter the test menu. (Refer to “Setting method of the test mode menu” on page xx) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “MC.X.XXX” (X.XXX: MC (-com) version). (Displayed values in the above figure are example) 2-5. Serial Flash Version Display Mode It can display the SF (serial flash) version. Procedure: 1. Enter the test menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “SF.X.XXX” (X.XXX: SF (serial flash) version). When [INPUT] button is pressed again, the display returns to the each version display. (Displayed values in the above figure are example) 28 HT-ST7 2-6. DSP Sound Number Display Mode It can display the SN (DSP sound number) number. Procedure: 1. Enter the test menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “SN XXX” (XXX: DSP sound number (000 to 998)). (Displayed values in the above figure are example) Note: “SN ---” is displayed when the information of serial flash is not able to be acquired. 2-7. BT Module F/W Version Display Mode It can display the BT (Bluetooth) module firmware varsion. Procedure: 1. Enter the test menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “BTM.X.XX” (X.XX: BT (Bluetooth) module firmware version). (Displayed values in the above figure are example) 2-8. AMP Test Mode (It is displayed “AMP” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. 2-9. Tone Test Mode It can confirm the test tone output from each speaker. Preparation: Connect the Subwoofer (SA-WST7) and the Sound Bar (SA-ST7) by wireless. Note: Refer to “SETTING METHOD OF THE WIRELESS CONNECTION ”on page 4 for details of wireless connection. Procedure: 1. Enter the test mode menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “T TONE”, press the [INPUT] button. 3. The message “TONE.ON” is displayed on the fluorescent indicator tube momentarily and enter the tone test mode. 4. The output speaker is displayed on the fluorescent indicator tube. At the same time, test tone is output from speaker. (The output speaker repeatedly changes automatically in following order) Output speaker Display Front L-ch L3 Surround Back R-ch R1 Surround L-ch L2 Surround R-ch R2 Surround Back L-ch L1 Front R-ch R3 Center C Subwoofer SW 2-18. Wireless Sound Test Mode It can display the -com version of Subwoofer (SA-WST7). Note :More than one item may be displayed on the fluorescent indicator tube, but it is not used for the servicing other than “VER.CHE”. Preparation: • Prepare the remote commander attached to this unit. Remote commander: RM-AMU164 • Connect the Subwoofer (SA-WST7) and the Sound Bar (SAST7) by wireless. Note: Refer to “SETTING METHOD OF THE WIRELESS CONNECTION ”on page 4 for details of wireless connection. Procedure: 1. Enter the test mode menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “WS TST”, press the [INPUT] button. 3. The message “QUALIT” is displayed on the fluorescent indicator tube momentarily and enter the wireless sound test mode. 4. Press the [V]/[v] buttons on the remote commander, select the “VER.CHE”, and press the [ENTER] button on the remote commander. 5. The -com version of Subwoofer (SA-WST7) is displayed on the fluorescent indicator tube. Releasing method: Press the [?/1] button to release the test mode menu. 2-10. Speaker Test Mode (It is displayed “SPK.TST” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. 2-11. VACS Display Mode (It is displayed “V. DISP” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. Preparation: Connect the Subwoofer (SA-WST7) and the Sound Bar (SA-ST7) by wireless. Note: Refer to “SETTING METHOD OF THE WIRELESS CONNECTION ”on page 4 for details of wireless connection. Procedure: 1. Enter the test mode menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “WS RST”, press the [INPUT] button. 3. The [?/1] indicator LED on the Subwoofer (SA-WST7) turns red and flashes, then turns on yellow. [?/1] indicator LED Red (flash) t Yellow (light up) 4. Pull out the power cord on the Subwoofer (SA-WST7) from an outlet and insert the power cord again. 2-12. VACS ON/OFF Mode (It is displayed “V.ONOFF” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. (Displayed values in the above figure are example) 6. When [V]/[v] buttons on the remote commander is pressed while the -com version of Subwoofer (SA-WST7) is displayed on the fluorescent indicator tube, year, month and day of the creation is displayed on the fluorescent indicator tube. 2-13. DSP Halt Mode (It is displayed “DSP.HLT” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. 2-14. DSP Serial Flash Update Mode (It is displayed “SF UPD” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. (Displayed values in the above figure are example) When [V]/[v] buttons on the remote commander is pressed again, the display returns to the -com version of Subwoofer (SA-WST7) display. 2-15. Stream Information Mode (It is displayed “STREAM” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. Releasing method: Press the [?/1] button to release the test mode menu. 2-16. HDCP Key Read Mode (It is displayed “HDCP” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. 2-17. NFC Test Mode (It is displayed “NFC.TST” on the fluorescent indicator tube) Not used for the servicing. Press the [?/1] button if having entered this mode. HT-ST7 2-19. Wireless Sound Cold Reset It can initialize various backup information of Subwoofer (SAWST7). 29 29 2-20. Cold Reset It can initialize various backup information. Procedure: 1. Enter the test mode menu. (Refer to “Setting method of the test mode menu” on page 27) 2. Press the [VOLUME +]/[VOLUME –] buttons to select the “RESET”, press the [INPUT] button. 3. The message “RESET” is displayed on the fluorescent indicator tube, then turn the power off. HT-ST7 SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM - HDMI Section HDMI TRANSCEIVER IC3506 >001B DATA0+ DATA0– 7 9 42 R3X0+ 41 R3X0– DATA1+ DATA1– 4 6 44 R3X1+ 43 R3X1– DATA2+ DATA2– 1 3 46 R3X2+ 45 R3X2– CLOCK+ CLOCK– 10 12 40 R3XC+ 39 R3XC– SDA (5V) SCL (5V) 16 15 88 DSDA3 89 DSCL3 HOT PLUG DET 19 90 CBUS_HPD3 +5V POWER 18 91 R3PWR5V CEC 13 DATA0+ DATA0– 7 9 50 R4X0+ 49 R4X0– R1X0+ 145 R1X0– 144 7 9 DATA0+ DATA0– DATA1+ DATA1– 4 6 52 R4X1+ 51 R4X1– R1X1+ 147 R1X1– 146 4 6 DATA1+ DATA1– DATA2+ DATA2– 1 3 54 R4X2+ 53 R4X2– R1X2+ 149 R1X2– 148 1 3 DATA2+ DATA2– CLOCK+ CLOCK– 10 12 48 R4XC+ 47 R4XC– R1XC+ 143 R1XC– 142 10 12 CLOCK+ CLOCK– SDA (5V) SCL (5V) 16 15 92 DSDA4 93 DSCL4 HOT PLUG DET 19 +5V POWER 18 CEC 13 DATA0+ DATA0– 7 9 60 R5X0+ 59 R5X0– DATA1+ DATA1– 4 6 62 R5X1+ 61 R5X1– DATA2+ DATA2– 1 3 64 R5X2+ 63 R5X2– CLOCK+ CLOCK– 10 12 58 R5XC+ 57 R5XC– SDA (5V) SCL (5V) 16 15 97 DSDA5 98 DSCL5 HOT PLUG DET 19 99 CBUS_HPD5 +5V POWER 18 100 R5PWR5V CEC 13 CN3503 1 HDMI IN HDMI_D0 – HDMI_D3, SP_SPDIF, ARC_SPDIF, HDMI_MCK, HDMI_BCK, HDMI_LRCK, RX_MUTE HDMI_D0 HDMI_D1 HDMI_D2 HDMI_D3 SP_SPDIF ARC_SPDIF HDMI_MCK HDMI_BCK HDMI_LRCK RX_MUTE CN3502 2 CN3501 3 SD0_0 SD0_1 SD0_2 SD0_3 SPDIF0_OUT SPDIF1_OUT MCLK SCK0 WS0_OUT MUTEOUT 124 126 127 128 130 136 125 122 121 129 (Page 31) SIGNAL PATH : AUDIO (DIGITAL) : VIDEO CN3200 HDMI OUT TV ARC ARC0 137 14 REVERSE (NC) 94 CBUS_HPD4 TXDSDA1 109 TXDSCL1 110 16 15 SDA (5V) SCL (5V) 95 R4PWR5V TX_HPD1 108 19 HOT PLUG DET 13 CEC SYSTEM CONTROLLER IC1002 (1/4) CSDA 67 CSCL 66 INT 68 RESET 69 VCC33OUT 102 45 HDMI_SDA 46 HDMI_SCL 56 HDMI_INT 54 HDMI_RST Q1004 15 CEC (I/O) XTALOUT 113 XTALIN 114 X3501 27MHz CEC >002B (Page 33) HT-ST7 30 30 HT-ST7 4-2. BLOCK DIAGRAM - MAIN Section A/D CONVERTER, DIGITAL AUDIO INTERFACE RECEIVER IC904 WAVE SHAPER IC205 J202 COAX DIGITAL IN 37 RXIN0 OPT 2 OPTICAL RECEIVER IC201 33 RXIN2 OPT 1 (TV) OPTICAL RECEIVER IC202 31 RXIN4 J201 ANALOG IN L 47 VINL R 48 VINR HDMI_D0 – HDMI_D3, SP_SPDIF, ARC_SPDIF, HDMI_MCK, HDMI_BCK, HDMI_LRCK, RX_MUTE DSP IC5001 DOUT 17 100 L/R_IN 103 DIR_IN 96 A/D_2CH MPIO_B1 12 MPIO_B2 13 MPIO_B3 14 74 SL/SR_IN 95 C/SW_IN 101 SBL/SBR_IN LEVEL SHIFT IC905 SCKO 20 >001B (Page 30) RX_MUTE D1001 6 8 9 10 32 35 3 4 5 MPIO_A3 MPIO_C1 MPIO_C2 MPIO_C3 RXIN3 RXIN1 MPIO_A0 MPIO_A1 MPIO_A2 PCM_OUT PCM_CLK PCM_SYNC 28 30 29 16 AMP_D2SL/SR AMP_D3CSW AMP_D4SBL/SBR SL/SR_OUT 73 C/SW_OUT 94 SBL/SBR_OUT 88 BCLK_OUT 98 LRCK 18 97 LRCK_IN LRCK_OUT 99 CLKIN 24 SIGNAL PATH : AUDIO (ANALOG) : AUDIO (DIGITAL) 92 MCLK_IN 75 BCLK_IN : Bluetooth MCK DSP_BCK LEVEL SHIFT IC5102 (2/2) CN4002 DSP_LRCK EZW-RT50/ EZW-RT20 BUFFER IC5500 X5000 25MHz NPCM 2 5 6 2 3 14 13 ERROR 1 MPIO_C0 7 2A 2B 1A 1B 4A 4B 28 SDIO_Z 29 BCK_Z 30 LRCK_Z 21 I2CSDA 22 DATA SELECTOR IC5105 2Y 7 136 FLAG2 1Y 4 135 FLAG1 18 I2CCLK INT 23 RESET 2 DETECT SHIFT CONTROL IC5101 SWITCHING IC5012 (1/2), Q5001 4Y 12 SEL 1 SAMPLE RATE CONVERTER IC901 4 SDIN SDOUT 23 5 BCKI BCKO 25 6 LRCKI LRCKO 24 RCKI 2 >003B (Page 32) BCK 19 Q5002 BT1 Bluetooth MODULE AMP_D1FLFR L/R OUT 86 XTAL2 25 HDMI_D0 HDMI_D1 HDMI_D2 HDMI_D3 SP_SPDIF ARC_SPDIF HDMI_MCK HDMI_BCK HDMI_LRCK AMP_D1FLFR, AMP_D2SL/SR, AMP_D3CSW, AMP_D4SBL/SBR, MCK, DSP_BCK, DSP_LRCK SD-RAM IC5000 RXIN7 ABCKIO ALRCKIO MPO1 DATA0 – DATA15 DQ0 – DQ15 ADDR0 – ADDR9, SDA10, ADDR11 A0 – A11 SDCLK SDCKE SDRAS SDCAS SDWE ADDR17 ADDR18 MS0 SDDQM CLK SDCKE RAS# CAS# WE# BA0 BA1 MS0 SDDQM UDQM UART_OUT UART_IN MISO MOSI BOOT_CFG1 SPICLK DSP_CS DPI_P05 IRQ RESET SO SI SCK CE# HOLD# SERIAL FLASH IC5002 XTI 38 37 18 17 16 20 21 19 15 39 MDO MDI MC MS RST XTO RST 13 159 3 172 175 171 32 35 2 1 23 24 25 26 34 40 39 49 50 39 38 14 40 43 42 134 173 2 5 6 1 7 X901 24.576MHz HT-ST7 24 25 52 57 16 30 29 4 3 5 48 66 49 50 41 40 65 21 19 HDMI_MUTE_DET HDMI_MUTE_ON HDMI_NON_LPCM DIR ERROR DIR_XSTATE SEL_HDMI DIR_ZERO M_RX_IN_DSP M_TX_OUT_DSP DSP_MISO DSP_MOSI DSP_SPICLK DSP_SPIDS DSP_INTR DSP_RESET SF_HOLD_DSP WL_SDA WL_SCL WS_INT WL_RST WL_DET 34 33 32 36 73 42 47 55 DIR_DO (MC_DIR_DI) DIR_DI (MC_DIR_DO) DIR_CLK DIR_HCE DIR_RST BT_UART_TX BT_UART_RX BT_UART_RTS BT_UART_CTS MUTE RESET 98 99 100 51 53 A_SEL0 D1002 38 MC_BT-RXD0 MC_BT-TXD0 BUSY/RTS1 MC_BT_RTS BT_MUTE BT_RST SYSTEM CONTROLLER IC1002 (2/4) 31 31 EEPROM IC1001 ROM_SDA 8 5 SDA ROM_SCLK 9 6 SCL RF MODULATOR (EZW-RT50) HT-ST7 BLOCK DIAGRAM - AMP Section AMP_D1FLFR, AMP_D2SL/SR, AMP_D3CSW, AMP_D4SBL/SBR, MCK, DSP_BCK, DSP_LRCK >003B (Page 31) DIGITAL POWER AMP IC3007 STREAM PROCESSOR IC3004 AMP_D1FLFR DSP_BCK DSP_LRCK MCK 24 23 22 11 SDIN1 SCLK LRCK MCLK PWM_P_2 41 6 PWM_A OUT_A 39 PWM_M_2 40 8 PWM_B OUT_B 36 L3022 SP1 TWEETER (FRONT L-CH) SP2 WOOFER (FRONT L-CH) SP3 TWEETER (FRONT R-CH) SP4 WOOFER (FRONT R-CH) L3027 PWM_P_1 39 16 PWM_C PWM_M_1 38 18 PWM_D OUT_C 31 RESET_CD RESET_AB SD 4-3. OUT_D 28 17 7 5 DC DETECT Q3008 DIGITAL POWER AMP IC3005 AMP_D2SLSR 25 SDIN2 PWM_M_3 42 18 PWM_D OUT_D 28 PWM_P_3 43 16 PWM_C OUT_C 31 PWM_M_4 44 8 PWM_B OUT_B 36 PWM_P_4 45 6 PWM_A DC DETECT Q3009 L3019 SP5 SURROUND L-CH RESET_CD RESET_AB SD L3014 SP6 SURROUND R-CH OUT_A 39 17 7 5 DC DETECT Q3007 DIGITAL POWER AMP IC3003 AMP_D4SBLSBR 27 SDIN4 PWM_M_5 53 8 PWM_B OUT_B 36 PWM_P_5 54 6 PWM_A OUT_A 39 PWM_P_7 47 16 PWM_C OUT_C 31 PWM_M_7 46 18 PWM_D DC DETECT Q3006 L3007 SP7 SURROUND BACK L-CH RESET_CD RESET_AB SD L3013 SP8 SURROUND BACK R-CH OUT_D 28 17 7 5 DC DETECT Q3005 DIGITAL POWER AMP IC3001 PWM_P_6 56 16 PWM_C OUT_C 31 PWM_M_6 55 18 PWM_D OUT_D 28 RESET_CD RESET_AB SD 26 SDIN3 SDA SCL MUTE PDN RESET VALID AMP_D3CSW 20 21 19 18 16 37 17 7 5 L3006 SP9 (CENTER) DC DETECT Q3003 HT-ST7 32 28 27 67 69 68 26 18 11 13 74 DRIVE_RST DRIVE_SD (DIAG) Xout Xin DC_DET BUFFER Q3001 DAMP_SDA0 DAMP_SCL0 DAMP_SOFT_MUTE DAMP_PDN DAMP_INIT X1001 8MHz 32 SYSTEM CONTROLLER IC1002 (3/4) DC DETECT Q3004 SIGNAL PATH : AUDIO (ANALOG) : AUDIO (DIGITAL) HT-ST7 4-4. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section E12V SYSTEM CONTROLLER IC1002 (4/4) ND802 FLUORESCENT INDICATOR TUBE Data Clock CS Reset 75 77 76 58 HDMI1.3V DC/DC CONVERTER IC601 HDMI5V +5V REGULATOR IC6005 FL_DATA FL_CLK FL_CS FL_RESET +3.3V REGULATOR IC3704 HDMI3.3V REMOTE CONTROL RECEIVER IC801 PCONT_HDMI 78 1 SIRCS_IN HDMI5V POWER +5V REGULATOR IC6004 DSP1.1V DC/DC CONVERTER IC602 IR4V J251 IR BLASTER LED DRIVE Q2501 HDMI_TX_5VPWR 23 SWITCHING IC1007 OSC IC1006 PCONT_DSP 80 F1 F2 NFC1 NFC (RC-S801/A) NFC DAT SPICLK NFC IRQ NFC SW NFC SEL NFC RFDET 85 86 83 81 84 17 FOR FLUORESCENT INDICATOR TUBE DATA_NFC SPICLK_NFC IRQ_NFC SW_NFC SEL_NFC RFDET_NFC VH RECT D801, 802 T801 DC/DC CONVERTER TRANSFORMER OSC Q801, 802 VDD +3.3V REGULATOR IC802 SW3.3V +3.3V REGULATOR IC604 DIR3.3V +3.3V REGULATOR IC902 DIR5V +5V REGULATOR IC908 BT3.3V +3.3V REGULATOR IC906 IR3.3V +3.3V REGULATOR IC1005 DC/DC CONVERTER IC605 PCONT_3 59 D804 POWER INDICATOR LED DRIVE Q803 82 LED_PW D805 Bluetooth INDICATOR LED DRIVE Q804 2 TP_LED D806 (MUTING) LED DRIVE Q805 89 LED_MUTE P_CONT1 64 S751 I/1 72 KEY_INT 95 KEY0 S752, 755 (TOP PANEL KEYS) 93 KEY1 PCONT_BT 43 POWER CONTROL IC501 SHUNT REGULATOR IC502 PCON_IR 61 E4V E3.3V ISOLATOR PH502 6 BD D1006 S753, 754 (TOP PANEL KEYS) 92 KEY2 RESET SITCH Q1002 RESET 10 VOLTAGE DETECT IC1004 D1007 AC_CUT 71 >002B DC/DC CONVERTER IC603 +12V D1003 CEC F502 D516 RECT D519 +12V REGULATOR IC3008 REGULATOR Q501 3 Vcc/OVP 1 D D513 +25V D1008 SWITCHING Q1001 (Page 30) DIGITAL POWER AMP B+ +25V (FOR FL) F3007 +25V (FOR FR) F3008 +25V (FOR SL) F3005 +25V (FOR SR) F3006 +25V (FOR SBL) F3003 +25V (FOR SBR) F3004 +25V (FOR C) F3002 PCONT_2 63 HT-ST7 5 FB/OLP D512 33 33 D514 RECT D521 RECT D511 T501 POWER TRANSFORMER TH501 LINE FILTER L501 (US, CND) L501, 502 (AEP, UK, AUS) F901 Abbreviation AUS : Australian model CND : Canadian model AC1 (AC IN) HT-ST7 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. Note: • X : Parts extracted from the component side. • Y : Parts extracted from the conductor side. • f : Internal component. • : Pattern from the side which enables seeing. (The other layers’ patterns are not indicated.) Note: • All capacitors are in μF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : Internal component. • 2 : Nonflammable resistor. • 5 : Fusible resistor. • C : Panel designation. Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side) Caution: Pattern face side: (SIDE B) Parts face side: (SIDE A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. • MAIN board is multi-layer printed board. However, the patterns of intermediate layers have not been included in diagrams. • Indication of transistor. C Q These are omitted. B E • Abbreviation AUS : Australian model CND : Canadian model Note 1: When the complete AMP board is replaced, refer to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on page 4. Note 2: When the complete MAIN board is replaced, refer to “ABOUT THE PAIRING METHOD” on page 4. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Circuit Boards Location POWER board AMP board KEY board Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. MOUNTED board IO board Bluetoorh module (BT1) • A : B+ Line. • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : POWER ON • Voltages are taken with VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : AUDIO (ANALOG) J : AUDIO (DIGITAL) E : VIDEO N : Bluetooth • Abbreviation AUS : Australian model CND : Canadian model MAIN board DISPLAY board MOUNTED board NFC (RC-S801/A) (NFC1) Note 1: When the complete AMP board is replaced, refer to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on page 4. Note 2: When the complete MAIN board is replaced, refer to “ABOUT THE PAIRING METHOD” on page 4. HT-ST7 34 34 HT-ST7 SCHEMATIC DIAGRAM - MAIN Board (1/7) 1 3 2 4 • See page 52 for Waveforms. • See page 52 for IC Block Diagrams. • See page 58 for IC Pin Function Description. 6 5 7 8 9 10 12 11 13 15 14 17 16 18 19 20 IN3_D0– IN3_CK– IN3_D1– IN3_D1+ IN3_CK+ MAIN BOARD (1/7) A IN3_D0+ 4-5. (Page 39) CEC >101S PCON_HDMI MAIN BOARD (5/7) BUS1 HDMI_5VPWR C3520 0.1 B C3519 0.1 C3528 0.1 C3518 0.1 C3526 0.1 C3529 0.1 C3542 0.1 C3543 10 C3544 0.1 C3545 10 (Page 36) R3622 0 >102S BUS2 MAIN BOARD (2/7) VSYNC DE D19 D18 D17 D16 D15 D14 R0X0– R0XC– R0XC+ R0X1– R0X0+ R0X2– R0X1+ R0X2+ AVDD12 AVDD33 74 DSCL6 T1X1+ 147 75 LPSVCC33 T1X1– 146 76 DSDA0 T1X0+ 145 77 DSCL0 T1X0– 144 78 CBUS_HPD0 T1XC+ 143 79 R0PWR5V 80 DSDA1 TDVDD12 141 81 DSCL1 TPVDD12 140 82 CBUS_HPD1 83 R1PWR5V ARC1 138 84 DSDA2 ARC0 137 85 DSCL2 SPDIF1_OUT 136 86 CBUS_HPD2 87 R2PWR5V 88 DSDA3 3 7 DATA1– 6 DATA1 SHIELD 5 DATA1+ 4 DATA2– 3 DATA2 SHIELD 2 DATA2+ 1 M 0.5 DATA0– 10 CLOCK+ 11 CLOCK SHIELD 12 CLOCK– 13 CEC 14 RESERVE(NC) 15 SCL(5V) 16 SDA(5V) 17 R3387 1.8k DDC/CEC GND 18 +5V POWER 19 HOT PLUG DET R3377 47k OUT1_D2+ 0.5 OUT1_D2– 0.5 OUT1_D1+ 0.5 OUT1_D1– 0.5 OUT1_D0+ 0.5 OUT1_D0– 0.2 OUT1_CK+ 0.2 OUT1_CK– 1.3 1.3 1.3 0 0.6 C3358 1 R3370 300 C3558 0.1 R3637 47 3.2 ARC_SPDIF R3739 1k SCK1_OUT 134 R3365 10k GPIO10 0 0.1 C3564 10 C3559 0.1 C3548 0.1 C3560 10 R3741 10k R3646 0 R3645 0 47 47 R3627 R3628 5 R3632 0 R3606 0 220 VIN IC6004 +5V REGULATOR RX_MUTE VOUT 47 R3626 4 ECO 15 C3557 3 2 1 IC6004 R1191H050B-T1-FE FB3505 3.2 47 47 FB3503 R3620 R3623 100 R3618 R3733 100k C3565 10 SPDIFO_IN 133 GND JL3515 IN3_HPD IN3_SCL 9 R3621 FB3504 R3636 0 C3567 470 6.3V C3733 10 C3732 2.2 C3566 470 6.3V IN1_D0– IN1_D0+ R3722 1k IN1_D1– IN1_D1+ IN1_D2– IC6005 R1191N050B-TR-FE 15.1 5 E E IC3704 C3549 10p +3.3V REGULATOR IC3704 BD00IC0WEFJ-E2 +5V REGULATOR IN1_D2+ ET3501 1 IC6005 ET3500 (CHASSIS) IN3_SDA IN1_CK+ DATA0 SHIELD 1.3 SP_SPDIF DATA0+ C3540 0.1 SP_SD3 8 C3541 10 SP_SD2 DATA0 SHIELD C3534 1 R3519 22 IN1_CK– DATA0+ 8 1.3 L3500 10uH SP_SD1 9 C3729 4.7 SP_MCK 10 DATA0– R3726 4.7k SP_SD0 11 CLOCK+ C3527 4.7 SP_SCK CLOCK SHIELD R3597 4.7k SP_WS 12 C3532 4.7 OUT1_SCL 13 FB3506 R3600 4.7k OUT1_SDA 14 CEC CLOCK– C3538 10 OUT1_HPD RESERVE(NC) IN1_SCL R3602 0 DATA1– 7 JL3225 R3629 47 JL3513 IN1_SDA C3533 10 15 R3524 47k IN1_HPD 16 SCL(5V) R3509 0 DATA1 SHIELD JL3228 JL3520 C3536 0.1 IN1_SCL SDA(5V) R3518 22 10 IN2_HPD 17 10 R3601 IN2_SCL 18 10 R3598 IN1_SDA CN3501 19P +5V POWER DDC/CEC GND R3725 IN2_SDA K IN1_HPD R3376 47k R3386 1.8k R3643 0 R3640 0 R3599 4.7k R3508 0 R3380 1k C3562 10 WS1_OUT 135 R3616 47 19 DATA1+ 5 OUT1_HPD CVCC12 139 J HOT PLUG DET OUT1_SDA C3363 1 R3373 0 C3554 0.1 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 C3516 4.7 R3374 62 R3644 0 CE C3551 10 DATA2– 4 15.1 T1XC– 142 GPIO11 IN2_D2+ 0.1 DATA2 SHIELD 3 5 R1X0– R1XC– R1XC+ R1X1– R1X0+ R1X2– R1X1+ R1X2+ R2X0– R2XC– R2XC+ R2X1– R2X0+ R2X2– R2X1+ R2X2+ AVDD12 R3XC– AVDD33 CVCC12 R3X0– R3XC+ T1X2– 148 R3591 10k L HSYNC 1.3 3.3 1.3 1.3 3.3 0.5 0.5 0.5 0.5 DSDA6 SPDIF0_OUT C3546 0.1 73 MUTEOUT 0.5 IN2_D2– T1X2+ 149 3.2 3.3k IN2_D1+ CEC_A0WAKEUP SD0_3 1 0 72 0 2 DATA2+ R3510 2.2k IN2_D1– TPVDD12 150 SD0_2 DATA2 SHIELD 0 TDVDD12 151 CEC_A1 0 3 R3503 0 TPWR_CI2CA 71 SD0_1 4 DATA2– IN2_D0+ 0 70 T0XC– 152 MCLK DATA1+ IN2_D0– RESET SD0_0 5 R3505 2.2k 69 0.1 C3555 C3563 10 T0XC+ 153 0 6 0 INT C3553 OUT1_SCL C3364 1 T0X0– 154 0 DATA1– DATA1 SHIELD R3502 0 IN2_CK– IN2_CK+ 68 1.3 DATA2+ 2 T0X1– 156 1.5 7 0 CSDA R3372 62 C3552 0.1 1 6 OUT1_CK– T0X0+ 155 HDMI TRANSCEIVER IC3506 SII9573CTUC IOVCC33 DATA0+ R3504 2.2k 67 OUT1_D1+ 3.3 T0X1+ 157 IC3506 SCK0 8 0 CSCL 0 9 R3517 22 R3501 0 CVCC12 66 3.3 DATA0– DATA0 SHIELD IN2_SCL R5X2+ 65 0 10 0 IN2_SDA 64 OUT1_D2– JL3535 CLOCK+ 0 T0X2– 158 JL3534 11 R3579 0 R5X2– JL3533 12 0 63 JL3532 CLOCK– CLOCK SHIELD R3585 T0X2+ 159 1.3 13 0 CVCC12 160 R5X1+ 1.5 14 CEC 0 D0 161 R5X1– 62 1.5 RESERVE(NC) 0.1 R5X0+ 61 3.3 15 C3523 R3584 0 60 5 16 SCL(5V) R3523 47k 4.7k D1 162 1.3 17 SDA(5V) R3507 0 R3583 3.4 R5X0– 0 I DDC/CEC GND R3516 22 47 59 5 2 18 R3588 D2 163 DSCL3 HDMI IN +5V POWER IN2_HPD 2.2k 2.2k H CN3502 19P 19 R3578 G HOT PLUG DET R3576 R3506 0 R3573 HDMI_RST D3 164 R5XC+ WS0_OUT 3.3 HDMI_INT R5XC– 58 GPIO5 2.8 57 GPIO4 47 D4 165 GPIO3 1.6 AVDD33 GPIO2 R3590 HDMI_SDA 1.3 R3589 47 56 CVCC12 C3525 0.1 HDMI_SCL D5 166 XTALGND 0.5 AVDD12 XTALIN IN1_D2+ 55 XTALOUT 0.5 OUT1_CK+ D6 167 XTALVCC33 IN1_D2– D7 168 R4X2+ APLL12 0.5 R4X2– 54 TXDSCL1 0.5 IN1_D1+ 53 TXDSDA1 IN1_D1– OUT1_D0– TX_HPD1 0.5 D8 169 TXDSCL0 0.5 IN1_D0+ R4X1+ TXDSDA0 IN1_D0– 52 0 F 0.5 OUT1_D0+ D9 170 TX_HPD0 IN3_D2+ IN1_CK+ D10 171 R4X1– GPIO1 1 0.5 R4X0+ 51 GPIO0 2 DATA2+ IN1_CK– 50 JL3516 DATA2 SHIELD IN3_D2– 3.3 OUT1_D1– VCC33OUT 3 1.3 IDCK 172 3.4 DATA2– IN3_D1+ 0.5 R4X0– SBVCC5V 4 IN2_D2+ 49 R5PWR5V DATA1+ 0.5 D11 174 CBUS_HPD5 5 IN3_D1– IN2_D2– OUT1_D2+ IOVCC33 173 5 DATA1 SHIELD IN3_D0+ 0.5 HDMI OUT TV ARC R4XC+ 0 6 0.5 IN2_D1+ 1 R4XC– DSCL5 7 DATA1– IN2_D1– 2 48 0 DATA0+ 0.5 3 47 0 8 IN3_D0– 0.5 IN2_D0+ 4 D12 175 DSDA5 DATA0 SHIELD IN3_CK+ IN2_D0– 5 D13 176 0.5 9 0.5 6 R3X2+ RSVDL 10 DATA0– IN2_CK+ 7 R3X2– R4PWR5V CLOCK+ 0.5 8 46 CBUS_HPD4 11 IN2_CK– 9 45 0 12 0.5 0.3 CLOCK– CLOCK SHIELD IN3_CK– 0.5 IN3_D2+ DSCL4 13 IN3_D2– DSDA4 CEC IN3_SCL 0 14 IN3_SDA R3730 22 0 RESERVE(NC) R3731 47k R3X0+ 15 R3728 0 R3PWR5V SCL(5V) R3729 22 R3X1– 16 R3X1+ 17 0.5 E 18 SDA(5V) CN3200 19P 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 CBUS_HPD3 1 +5V POWER DDC/CEC GND IN3_HPD 0 CN3503 19P 19 0 D HOT PLUG DET 0.5 R3727 0 C 0.5 R3619 0 C3731 10 5 VIN 4 VOUT ECO 1 GND 2 CE 3 15.1 R3624 1M R3734 10k JL3519 2 4 R3593 1k 3.2 R3625 470 1 R3737 1k 3.2 X3501 27MHz C3730 2.2 R3732 100k C3550 10p C3725 1 8 VIN VOUT 1 7 6 NC FB 2 NC GND 3 5 EN NC 4 3.3 R3724 47k 0.8 (Page 41) JL3517 R3723 15k C3728 1 C3727 1 C3569 1 C3568 4.7 JL3528 DGND HDMI1.3V E12V E4V (CHASSIS) >103S MAIN BOARD (7/7) Note: IC3506 on the MAIN board cannot exchange with single. When this part is damaged, exchange the complete mounted board. HT-ST7 35 35 HT-ST7 4-6. SCHEMATIC DIAGRAM - MAIN Board (2/7) - 1 2 3 • See page 52 for Waveforms. • See page 52 for IC Block Diagrams. 4 5 6 7 8 9 10 12 13 14 15 MAIN BOARD (2/7) (Page 41) SP_WS 4 HDMI_LRCK C913 1 3 4 Vout Vin GND CE 1 R933 100 C914 1 JL936 4 R954 100 1.7 DIR_ER C941 0.1 L905 0.68uH R957 100 CL908 BUS5 MCK >105S MAIN BOARD (5/7) DIR_AD_D0 100 BCK R956 100 LRCK R958 100 DIR_D3 BYPAS TDMI 20 10 IFMT0 OFMT0 19 JL929 3.3 3.3 R915 100 F OWL0 17 13 RST OWL1 16 14 MUTE RDY 15 C908 0.1 3.3 9 BT_UART_RTS 10 BT_UART_CTS 11 3.3V 12 RESET 13 GND 14 BT_MUTE JL922 BT_TXD JL923 BT_RXD JL924 BT_RTS JL925 BT_CTS JL926 DGND 4 5 OPT_SAT 6 COAX 7 SW3.3V 8 DGND 9 0 0 1.5 1.2 1.6 1.6 1.5 3.3 3.3 MPIO_B2 MPO0 MPIO_B3 MPO1 DOUT LRCK BCK SCKO DVDD DGND 1 HDMI_MCK 0 CL925 3.3 CL926 R928 1k DIR_STATE DIR_NLPCM DIR_ERR 100 C932 1 IC906 37 38 39 40 41 42 43 44 45 46 47 48 C917 0.1 R961 100 R968 C934 1 +3.3V REGULATOR IC906 MM3411A33URE 3.3 JL937 3 Vout 4 Vin GND 2 CE 1 3.2 BUS4 R965 1k 1 R938 330 C918 4700p 2 2 C912 12p C916 15p C919 0.068 R943 680 4 5 IC908 BT_RESET C902 1 L903 10uH C921 10 R951 100 3 2 1 +5V REGULATOR IC908 R1191N050B-TR-FE D901 BAV99-215 JL902 JL903 JL904 JL905 R950 100 R908 0 R974 1k R909 0 R976 10k JL906 JL907 C923 100p C920 0.1 JL908 36 36 C924 100p C922 10 C933 100 10V C945 10 (Page 38) >106S MAIN BOARD (4/7) L907 220uH FB902 JL927 JL901 OPT_TV ERROR 36 VDDRX CL924 4 JL921 CN901 9P 3 2 HDMI_BCK 1.6 R967 100 PCONT_BT BT_UART_RX 2 NPCM 35 RXIN1 HDMI_LRCK CL923 X901 24.576MHz 8 LINE-L 3 CL922 0 R964 100 JL919 7 AGND_DIRAD MPIO_A0 0 JL918 MUTE 1 34 RST C904 10 JL917 BT_UART_TX LINE-R R911 100 4 HDMI_SD0 R963 100 DIR_D1 15.1 6 R910 100 5 MPIO_A1 CL921 VIN 5 GND ASEL_BT MPIO_A2 33 RXIN2 32 RXIN3 0 ECO GND R918 100k FB901 6 IC904 PCM9211PTR CL920 GND 4 C907 47p MPIO_A3 31 RXIN4 HDMI_SD1 3.3 15.1 PCM_SYNC 3.2 7 HDMI_SD2 0 CL919 5 3 10k MPIO_C0 HDMI_SD3 CL918 VOUT 2 PCM_CLK R925 3.2 A/D CONVERTER, DIGITAL AUDIO INTERFACE RECEIVER 30 ABCKI0 CL917 0 CE PCM_OUT 0 8 0 3.2 1 0 JL931 3.3 R922 0 GND JL930 JL932 R920 100 C901 0.1 CN902 14P 0 MPIO_C1 29 ALRCKI0 RXIN0 3.2 12 IFMT2 1.6 9 2.6 C903 0.01 CL909 100 JL928 C905 10 IC904 MPIO_C2 CL916 VINR 9 1.6 28 RXIN7 R960 100 CL915 0 2.4 DGND 21 3.3 MPIO_C3 10 VINL DGND JL910 27 MODE VCCAD 8 0 2.4 VDD 22 3.3 JL909 4.9 VIO 100 AGNDAD 7 100 R930 MPIO_B0 11 VCOM LRCKI SDOUT 23 R929 0 MPIO_B1 12 26 MS 2.4 6 1.6 25 MC FILT LRCKO 24 3.2 0 BCKI C911 0.1 0 JL934 VCC 5 C906 47p JL933 AGND SDIN BCKO 25 R921 100 R923 100 3.3 4 1.6 XTO MODE0 26 XTI MODE1 27 NC 1.7 RCKI 3 11 IFMT1 OFMT1 18 HT-ST7 GND PCON1 24 23 22 21 20 19 18 17 16 15 14 13 MDO 2 3.3 MDI LGAP MODE2 28 R927 100 1.7 3.3 R913 E 1 R924 100 R916 100k GNDRX 3.3 R914 2.2k 2.2k R912 2.2k (Page 47) 2 3.3 R959 100 R926 0 0 IO BOARD CN201 5 R955 0 IC901 0 >01S VCC L902 10uH SAMPLE RATE CONVERTER IC901 SRC4182 0 FFC2 NC MAIN BOARD (7/7) DIR_D2 1.5 H 1 >104S (Page 39) C940 10 BUS3 CL907 BUS2 D BT1 Bluetooth MODULE R949 100 1.5 R931 100 R919 0 FFC1 LEVEL SHIFT IC905 74LVC1G04GW-125 3 HDMI_MCK MAIN BOARD (1/7) G R934 100 DIR_XSTATE DIR_DI 3.2 ARC_SPDIF (Page 35) >102S IC905 2 SP_SPDIF C DIR_DO DIR_CE R973 1k HDMI_BCK R907 220 SP_MCK 3.3 DIR_ZERO JL935 R906 100 SP_SCK IC902 HDMI_SD3 R905 100 AGND +3.3V REGULATOR IC902 MM3411A33URE HDMI_SD2 R904 100 SP_SD3 E12V JL940 L906 10uH HDMI_SD1 R903 100 SP_SD2 B HDMI_SD0 R902 100 SP_SD1 E4V DIR_CLK SP_SD0 DGND FB903 JL938 R901 100 DIR_RST A I 11 C946 2.2 HT-ST7 4-7. SCHEMATIC DIAGRAM - MAIN Board (3/7) 1 A 3 2 • See page 52 for Waveforms. • See page 58 for IC Pin Function Description. 4 MAIN BOARD (3/7) 6 5 7 8 9 10 13 15 14 17 16 C5003 0.1 C5002 0.1 C5001 0.1 C5000 0.1 C5070 470 6.3V 2 C5014 0.01 C5012 0.1 C5051 0.1 C5052 10 C5055 470 6.3V C5058 0.1 19 (Page 41) CL5005 FL5002 X5000 25MHz O EMI I G C5007 0.1 18 R5052 0 FB5000 FL5000 C5004 0.1 12 11 C5059 10 SW3.3V >107S CL5006 DSP1.1V O EMI I G MAIN BOARD (7/7) DGND G O SPI_CLK EMI I FL5003 C5008 10 R5514 1M R5513 1k SPI_MOSI DSP_SPI_CS B SPI_MISO 1 C5009 470 6.3V 3 C5506 10p C5505 22p (Page 38) IC5000 IC5002 SPI_MOSI SPI_CLK SERIAL FLASH IC5002 W25Q16CVSSIG-R 3.2 L JL5007 3.1 JL5008 3.1 C5074 0.1 1 CE# 2 SO 3 WP# 4 C5076 10 Vss Vdd R5078 22 8 HOLD# 7 SCK 6 SI 5 R5079 10k R5082 22 R5084 10k 3.1 0 3.2 JL5010 2.8 JL5009 MSO SDCKE SDDQM A0 A1 A2 A3 A4 A5 A6 A7 R5049 R5048 JL5004 150 150 0 R5055 100 R5047 3.3 R5054 100 R5046 10k 100 R5045 3.3 100 100 R5044 0 10k 100 R5043 3.3 R5051 150 R5042 2.9 R5039 100 100 100 R5037 0 R5040 100 R5036 3.3 3.3 10k R5035 0 R5031 150 0 SDDQM 3.3 MS0 3.3 SDCKE 1.1 VDD_INT 0 3.3 CLK_CFG1 3.3 ADDR0 3.3 BOOT_CFG0 ADDR2 ADDR3 ADDR4 ADDR5 BOOT_CFG1 GND ADDR6 NC ADDR7 NC ADDR8 ADDR9 CLK_CFG0 CLKIN XTAL2 VDD_INT SDA10 ADDR10 VDD_EXT AMI_RD AMI_WR ADDR14 VDD_INT ADDR15 ADDR16 VDD_INT 133 4 5 C5056 0.1 R5080 22 R5081 2.2k MCK JL5006 37 37 1.1 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 3.3 0.1 VDDEXT 88 IRQ 134 ADDR19 87 ADDR20 C5050 FLAG1 135 SBL/SBR_OUT VDD_INT 0.1 FLAG2 136 MID/SW2_OUT 1.1 C5048 VDD_EXT VDD_INT 86 ADDR21 0.1 ADDR11 85 MLBCLK 137 L/R_OUT ADDR22 0.1 C5047 VDD_INT VDD_EXT ADDR23 0.1 C5046 ADDR12 84 VDD_EXT C5042 ADDR17 FLAG3 138 WDT_CLKIN 0.1 ADDR13 MLBDAT 139 NC 3.3 0.1 C5039 VDD_INT MLBDO 140 NC 83 WDT_CLKO C5036 ADDR18 NC 82 0 0.1 ADDR1 3.3 1.1 1.6 1.7 3.3 3.3 1.1 0 0 JL5001 1.1 0 1.1 81 1.1 0.1 C5033 MOSI VDD_EXT 141 3.3 C5030 VDD_INT MLBSIG 142 NC TRST 144 1.1 0.1 RESETOUT/RUNRSTIN NC 80 C5027 0.1 C5029 MISO 79 MLBSO 145 VDD_INT 143 FB5001 HT-ST7 A8 A9 A10 A11 R5028 100 22 R5017 2.9 R5025 100 22 R5021 100 22 R5015 VDD_INT JL5005 M R5014 FRONTHI_L/R_OUT 78 R5041 10k DSP_SFLASH_HOLD R5059 10k OPTION_L/OPTION_R_OUT 77 10k R5058 22 76 DIR_D3 R5056 22 EMU 146 DSP_BCK R5053 10k BCLK_IN R5038 SPI_MISO 75 JL5013 DSP_SPI_CS K 0 DATA0 147 1.1 R5009 100 CL5000 SL/SR_IN VDD_INT JL5036 0 74 1.1 AMP_D4SBLSBR R5008 100 DATA1 148 MS1 JL5035 AMP_D1FLFR SL/SR_OUT VDD_INT 1.1 73 VDD_INT 3.3 J DATA2 149 3.3 10 DATA3 150 VDD_EXT JL5003 0.1 C5017 NC 72 TDO 151 JL5002 C5028 71 DATA4 152 1.1 0.1 NC WDTRSTO 1.1 0.1 C5026 VDD_EXT 153 70 3.3 C5022 DATA5 154 69 1.2 10 VDD_INT DATA6 155 DSP 22 C5019 68 VDD_INT 156 IC5001 ADSST-AVR-3046 VDD_EXT 1.1 NC THD_P JL5034 NC 67 R5029 0.1 66 IC5001 0 C5020 VDD_INT 1.1 0.1 65 1.2 C5040 DATA7 157 SDCLK 159 THD_M 1.6 TDI 158 NC GND 0 JL5030 NC 64 AMI_ACK JL5031 22 VDD_INT 63 VDD_INT 22 R5005 62 BOOT_CFG2 R5004 BCK 0 VDD_EXT 160 VDD_INT JL5032 NC VDD_EXT DIR_D1 I 100 61 DIR_IN R5003 DATA8 161 VDD_INT 3.3 AMP_D2SLSR DATA9 162 NC SBL/SBR_IN C5018 470 6.3V DATA10 163 NC 60 L/R_IN 1.1 NC 59 JL5043 0.1 58 TCK 164 22 C5025 VDD_EXT R5026 0.1 57 LRCLK_OUT A4 C5024 DATA11 165 22 A5 0 1.1 NC R5024 3.3 0.1 56 BCLK_OUT A6 VSS 28 27 VDD 3.1 22 R5012 A7 3.3 0.1 C5023 DATA12 166 1.6 A4 29 3.3 C5021 NC JL5039 A5 30 26 A3 A8 55 100 3.3 R5001 10k 25 A2 A9 0 DATA14 167 R5023 3.3 A6 31 3.3 1.1 DATA13 168 NC DSP_LRCK_OUT 3.3 A3 A7 32 24 A1 A11 0 NC 54 1.6 A2 23 A0 C5071 470 6.3V 53 JL5038 0 A8 33 22 A10 SDCKE 3.3 SDWE 171 DATA15 170 220 3.3 A1 A9 34 3.3 RESET 173 R5022 A0 21 BA1 CLK 1.5 VDD_INT 176 VDD_INT 169 LRCLK_IN 3.3 A11 35 0.1 1 NC A/D_2CH 0 A10 20 BA0 C5032 2 UART_IN C/SW_IN BA1 NC 36 0.1 3 LED 1.6 0 SDCKE 37 19 MSO 0.1 C5034 4 52 1.2 BA0 18 RAS# C5035 5 51 JL5040 3.3 CLK 38 0.1 6 50 JL5041 3.3 MSO 17 CAS# 0 C5038 CL5002 LRCK H RAS# UDQM 39 0.1 DIR_AD_D0 G 3.3 16 WE# 10 7 SDRAS 172 22 CAS# NC 40 15 SDDQM C5057 C5044 UART_OUT 22 3.3 R5516 100k VDD_INT 49 8 TMS 174 R5020 WE# 2.4 48 C5065 0.1 9 SDCAS 175 R5019 0 3.2 RESET_MAIN DIR_D2 SDDQM 3.3 DSP_RXD VSS 41 14 VDD 1.1 DSP_TXD 47 C/SW1_OUT R5000 100 DQ8 42 13 DQ7 D8 3.3 NC AMP_D3CSW F 3.3 2.4 CL5001 VDD_EXT 46 0 2.4 R5515 100k D9 45 JL5042 VDDQ 43 12 VSSQ C5053 0.1 22 DQ9 44 11 DQ6 3.3 D11 D10 R5018 DQ10 45 10 DQ5 RB5003 100 2.4 SPICLK VSSQ 46 VDD_INT VDDQ R5057 68 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 2.4 VDD_INT 9 2.4 MCLK_IN DQ11 47 0 DQ12 48 DQ4 1.1 DQ3 8 1.1 7 D12 JL5037 2.4 D7 VDDQ 49 100 D6 VSSQ R5016 2.4 D5 6 D13 3.3 DPI_P05 3.3 D4 MAIN BOARD (4/7) D14 2.4 VDD_EXT RB5001 100 E DQ13 50 DQ2 8 D15 1.7 2.4 5 DQ14 51 DQ1 22 2.4 4 RB5002 100 2.4 R5013 D3 VSSQ 52 CL5003 2.4 VDDQ 3.2 D2 3 2.4 3.2 2.4 DQ15 53 MD D1 VSS 54 DQ0 DSP_CS D0 VDD 2 VDD_INT D 3.3 1 ZONE_L/R 2.4 RB5000 100 R5011 22 C5006 0.1 3.2 IC5000 W9864G6JH-6-ER10 3.3 >108S 9 C5005 0.1 SD-RAM 3.3 C BA0 JL5000 BA1 10 R5072 100k 1.1 3.3 JL5023 R5065 150 CAS# R5074 1k 3.3 R5066 150 RAS# 3.3 R5067 150 WE# 3.2 DSP_RESET D15 2.4 1.1 2.4 D13 2.4 D14 D12 2.4 D11 2.4 R5527 0 0 R5027 10k 2.4 D10 2.4 D9 D8 2.4 3.3 R5075 1.6 150 CLK D7 2.4 1.1 2.4 D6 2.4 D5 3.3 2.4 D4 2.4 D3 2.4 D2 2.4 D1 D0 2.4 R5060 R5531 0.8 0 R5030 0 10k 1.1 C5064 0.1 3.3 R5061 0 R5062 10k R5063 10k JL5024 0 JL5022 R5068 22 3.3 JL5021 R5069 22 ERROR 0 JL5020 R5070 22 DSP_INT NONPCM 1.1 R5064 2.2k C5066 0.1 C5068 0.1 C5069 0.1 C5062 0.1 C5067 0.1 C5060 0.1 C5061 0.1 DSP_INT C5072 10 DSP_RESET C5054 0.1 DSP_SFLASH_HOLD C5049 0.1 DSP_SPI_CS C5045 0.1 SPI_MISO C5037 0.1 SPI_MOSI C5031 0.1 D5001 DB2S31100K8 DSP_INT DSP_RESET DSP_SFLASH_HOLD DSP_SPI_CS SPI_MISO SPI_MOSI SPI_CLK DSP_RXD CL5007 DSP_TXD CL5008 SPI_CLK DSP_RXD DSP_TXD (Page 39) >109S MAIN BOARD (5/7) HT-ST7 4-8. SCHEMATIC DIAGRAM - MAIN Board (4/7) - 2 1 • See page 52 for IC Block Diagrams. 3 4 5 6 7 8 9 10 12 11 MAIN BOARD (4/7) A 13 S_MUTE DRIVER_RST >108S MAIN BOARD (3/7) DSP_LRCK (Page 37) MCK DSP_LRCK_OUT 8 R5007 0 (Page 39) SD >110S DC_PRT MAIN BOARD (5/7) OVF1 DAMP_PDN AMP_SDA 9 B NS_INIT 10 AMP_SCL R5102 220k R5101 100 FB5003 CN5002 28P 3.3 1.6 3.2 RB5004 100 5 1 2 3 JL5506 JL5507 3.2 4 JL5508 3.3 JL5509 Q5001 LTA014TUBFS8TL SWITCHING D C5041 10 C5043 0.1 C5501 0.1 JL5101 C5502 0.1 C5105 0.22 JL5510 R5517 47 R5103 100 DSP_BCK FB5002 DSP_LRCK E R5108 10k AMP_D1FLFR 3.3 1.6 G 1.6 1 C5503 0.1 8 7 3 4 C5016 10 VCC 2 6 GND 5 3B 3A 4Y 4B 4A 2B 2Y GND JL5512 R5507 47 JL5513 R5508 47 JL5514 R5509 47 JL5515 AMP_D2SLSR R5510 47 AMP_D4SBLSBR R5511 47 JL5516 JL5517 0 JL5519 DIR_STATE HDMI_MUTE R5525 100 DGND 6 AMP_PDN 7 AMP_ERR 8 DC_PRT 9 DRIVER_SD 10 AMP_INIT 11 DRIVER_RST 12 AMP_MUTE 13 DGND 14 AMP_MCK 15 DGND 16 AMP_BCK 17 DGND 18 AMP_LRCK 19 DGND 20 AMP_D1(FL/FR) 21 DGND 22 AMP_D3(C/SW) FFC3 >02S AMP BOARD (1/2) CN3001 (Page 44) 23 DGND 24 AMP_D2(SL/SR) 25 DGND 26 AMP_D4(SRB) 27 DGND 28 Pcon2 (Page 36) >106S MAIN BOARD (2/7) HDMI_NLPCM 1.6 DIR_NLPCM 1.6 ERROR R5500 100 AMP_D3CSW DSP_BCK DSP_LRCK L5504 0.68uH SW3.3V HDMI_MUTE SEL_HDMI HDMI_NLPCM PCON2 (Page 39) HDMI_MUTE >111S SEL_HDMI HDMI_NLPCM WL_D3CSW WL_LRCK (CHASSIS) HT-ST7 AMP_SDA 5 NONPCM JL5500 R5502 100 D3.3V 4 BUS4 0 E ET5001 E (CHASSIS) AMP_SCL 3 INVERTER DIR_ERR H D3.3V 2 Q5002 LTC014EUBFS8TL SEL_HDMI ET5000 1 0 2A 8 3.2 1Y 7 0 1B 6 3.3 1A 5 3 SEL 4 0 3 3.3 2 JL5511 3.3 R5501 220 C5500 0.1 1 RB5005 100 JL5518 3 IC5105 TC74VHC157FT(EKJ) BUFFER IC5500 TC7WH34FK(TE85R) R5506 47 9 DATA SELECTOR IC5500 0 VDD IC5105 ST 16 15 14 13 12 11 10 3Y 0 3.3 3.3 AMP_D3CSW F JL5503 JL5505 GND DGND SWITCHING, LEVEL SHIFT IC5102 TC7WZ08FK(TE85R) 3 JL5502 Vcc 6 3.3 2 7 JL5501 JL5504 3.3 3.3 1 CLK D SHIFT CONTROL IC5101 74LVC1G79GW-125 IC5102 Q VCC IC5101 8 1.6 C 4 1.6 5 3.3 3.3 3.3 R5523 100 WL_BCK 38 38 MAIN BOARD (5/7) HT-ST7 4-9. SCHEMATIC DIAGRAM - MAIN Board (5/7) 1 A 3 2 • See page 52 for Waveforms. • See page 58 for IC Pin Function Description. 4 6 5 7 8 9 10 12 11 13 15 14 18 MAIN BOARD (5/7) (Page 35) CEC >101S HDMI_5VPWR MAIN BOARD (1/7) BUS1 PCON_HDMI C1201 0.1 JL1012 (Page 36) >105S MAIN BOARD (2/7) JL1007 R1231 0 BUS5 BT_MUTE B 17 16 BUS3 PCON1 C1202 470 6.3V FB1001 SW3.3V (Page 38) D1001 DB2S31100K8 WL_INT PCON2 MAIN BOARD (4/7) HDMI_NLPCM DIR_CE DIR_RST DIR_XSTATE SEL_HDMI S_MUTE OVF1 NS_INIT DAMP_PDN DC_PRT FL_RESET >113S MAIN BOARD (6/7) Q1004 LTC014EUBFS8TL INVERTER R1030 10k 7 3.4 0 R1015 10k JL1053 HDMI_RST 6 HDMI_INT PCONT_IR WL_RST 3.2 3.3 3.2 0 3.2 3.3 0 JL1052 3.2 13 100 3.2 12 R1232 JL1054 3.2 DGND WL_LRCK JL1055 0 11 WL_SCL 3.2 10 WL_SDA 100 3.2 DGND WL_BCK 100 R1233 3.2 9 R1234 JL1056 0 8 WL_D0 JL1057 (Page 40) 3 5 3.2 WR_RESET WL_INT 2 R1022 47k 3.2 7 100 3.2 WL_SCL R1235 0 6 JL1058 1 4 3.2 5 WL_DET 3.2 WL_SDA WL_RESERVED 100 R1031 10k FL_DATA 4 R1236 FL_CS 3 WL_INT JL1059 2.5 (Page 47) WL_DET JL1061 3.3 IO BOARD CN4001 2 R1021 100 3.2 >03S WL_RF FL_CLK FFC4 1 LED_MUTE D SW3.3V HDMI_NLPCM CN1001 13P D1002 DB2S31100K8 WL_BCK DSP_INT WL_LRCK WL_D3CSW E RX_MUTE HDMI_MUTE >111S C SEL_HDMI SEL_HDMI SPI_CLK DSP_RXD DSP_RXD DSP_TXD DSP_TXD SPI_MOSI SPI_MISO DIR_HCE DIR_XSTATE DIR_RST HDMI_RST 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 2.9 R1055 100k R1047 47 1.6 HDMI_SCL 2.8 R1048 47 3.2 R1058 10k 3.2 R1049 100 PCONT_BT 3.2 R1062 100 BT_RESET HDMI_SDA WL_SDA 3.3 WL_SCL 3.3 0 R1050 10k 3.2 R1059 100 R1240 4.7k BT_CTS R1051 4.7k JL1027 3.1 R1064 100 0 R1053 100 3.2 R1054 100 2.6 R1045 47 3.2 4.7k ASEL_BT R1060 100 0 R1239 R1069 R1063 100 100 DSP_RXD BT_TXD BT_RXD RTS1 0.1 SCO/CLK1 0 2.6 TXD1 R1237 R1042 10k R1046 47 3.2 RXD1 R1052 47k R1238 2.2k R1061 100 2.2k D1004 DB2S31100K8 BT_RTS DSP_TXD R1068 100 3.3 0 DIR ERROR 9 3.2 8 JL1001 R1065 100 DIR_ER CL1008 WL_DET CL1010 WL_RST RFDET_NFC R1028 100k R1026 100k TP_LED R1018 100k SIRCS KEY2 KEY1 KEY0 R1023 100 R1037 47k C1007 0.1 CL1003 C1005 0.1 R1034 1M R1006 4.7k HDMI_MUTE_ON 7 N.A. 6 WL_RST 5 26 DSP_RESET DSP_SPI_CS 3.2 DIR_ZERO R1027 100 C1006 0.1 CL1002 HDMI_INT 4 N.A. 3 WL_DET 2 R1025 100 R1029 100 R1007 4.7k 27 1 SPI_CLK K 28 DSP_SFLASH_HOLD 3.2 HDMI_NLPCM SPI_CLK 29 HDMI_NON_LPCM 99 100 M_RX_IN_DSP 30 DRIVE_RST DIR_CLK HDMI_TX_5VPWR DIR_DI(MC_DIR_DO) SPI_MOSI SPI_MOSI SEL_HDMI P_CONT3 FL_RESET Vcc2 PCON_IR Vss P_CONT2 P_CONT1 WS_INT DSP_INTR DAMP_INIT DAMP_SOFT_MUTE N.A. DAMP_PDN AC_CUT KEY_INT DIR_DO(MC_DIR_DI) AVcc 98 C1003 0.1 SPI_MISO SPI_MISO BT_MUTE Vref 97 SCD/CLK1 31 DAMP_SCLO 3.2 DSP_SPI_CS DSP_SPI_CS DC_DET 96 DSP_SFLASH_HOLD DSP_SFLASH_HOLD BUSY/RTS1 32 DAMP_SDAO C1002 0.1 DSP_RESET DSP_RESET MC_BT_TXD0 33 M_TX_OUT_DSP DRIVE_SD(DIAG) KEY0 RFDET_NFC 0 AVss 95 0 CL1011 MAIN BOARD (3/7) DIR_CLK KEY1 94 CL1009 >109S 0 93 MC_BT_RXD0 34 DSP_INT DSP_INT (Page 37) DIR_DI KEY2 N.A. 35 3.2 I 3.3 92 MC_BT_RTS 36 3.2 3.2 DIR_DO MODEL 3.2 3.2 DESTINATION 91 N.A. 37 DIR_ZERO 3.2 90 CEC(I/O) 100 SYSTEM CONTROLLER IC1002 R5F3650NCDFB A_SEL0 38 LED_MUTE HOLD 39 1.2 R1012 N.A. 89 Vcc1 3.2 AMP_SCL AMP_SCL J R1003 10k 100 88 3.2 R1002 10k AMP_SDA R1011 N.A. Xin DAMP_PDN AMP_SDA 3.2 87 IC1002 WL_SCL 40 Vss OVF1 DAMP_PDN 0 100 SPICLK_NFC 3.2 OVF1 10k 86 1.6 DC_PRT R1014 R1010 WL_SDA 41 Xout R1001 10k DC_PRT DATA_NFC 1.8 SD SD 85 CL1006 MAIN BOARD (4/7) NS_INIT 3.2 BT_RST 42 CL1004 >110S 0 R1004 NS_INIT SEL_NFC 1.6 H DRIVER_RST DRIVER_RST R1016 1k 84 WR_Flash 44 RESET S_MUTE S_MUTE (Page 38) R1017 10k 3.2 PCONT_BT 43 ROM_SCLK SPICLK_NFC IRQ_NFC ROM_SDA 0 LED_PW 83 HDMI_SDA 45 HDMI_MUTE_DET 3.2 DATA_NFC 82 HDMI_SCL 46 DSP_SPIDS 3.2 0 DSP_RESET CNVss 0 SEL_NFC SW_NFC 3.2 IRQ_NFC PCONT_DSP 81 BYTE 0 47 N.A. 80 DSP_SPICLK (US, CND, AUS) LED_PW 48 SF_HOLD_DSP 79 3.2 R1013 47k R1004 22k (US, CND, AUS) 4.7k (AEP, UK) 0 PCONT_HDMI 50 49 DSP MISO G SW_NFC 78 3.2 3.2 DGND FL_CLK 3.1 CL1209 PCON_DSP FL_CS 77 DSP MOSI 3.2 PCON_HDMI 76 TP_LED 3.2 PCON1 SIRCS_IN MAIN BOARD (7/7) 3.1 PCON3 3 >112S SW3.3V 0 (Page 41) FL_DATA 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 F X1001 8MHz R1033 0 L R1041 100k R1040 100 6 CN1006 9P S Q1001 LSK3541FS8T2L SWITCHING 7.2 R1039 HT-ST7 39 39 AMP_SDA 4 R1020 100 3.2 AMP_SCL 3 3.2 DRIVER_RST 2 R1038 27k TXD1 JL1040 RTS1 JL1041 JL1042 SD GND 1 R1008 100k R1107 4.7k UCOM_RESET C1001 0.1 A2 M A1 IC1001 R1EX24016ASAS0A A0 EEPROM R1032 100k CNVSS 5 SCL 3.2 6 SDA 3.2 7 WP IC1001 8 VCC 3.2 JL1039 SCO/CLK1 R1095 100 JL1043 RXD1 R1096 100 JL1044 CNVSS R1097 100 JL1045 JL1046 UCOM_RESET R1098 100 1 GND 2 TXD1 3 RTS1 4 3.3V 5 CLK1 6 RXD1 7 CNVSS 8 RESET 9 GND (NC) 1k Note: When IC1002 on the MAIN board is replaced, refer to “ABOUT THE PAIRING METHOD” on page 4. HT-ST7 4-10. SCHEMATIC DIAGRAM - MAIN Board (6/7) - 1 2 • See page 52 for IC Block Diagrams. 3 4 5 6 7 8 9 10 MAIN BOARD (6/7) A 11 CN1002 8P JL1014 SPICLK_NFC R1101 100 JL1018 DATA_NFC R1102 100 JL1019 SEL_NFC R1103 IRQ_NFC R1104 100 JL1021 SW_NFC R1105 100 JL1022 100 B SPI_CLK 3 NFC_DAT 4 NFC_SEL 5 NFC_IRQ 6 NFC_SW 7 NFC_RFDET 8 GND 1 IR4V 2 GND 3 REMOTE 15 E3.3V 14 SIRCS 13 DGND 12 FL_CLK 11 FL_CS 10 FL_DATA 9 8V 8 8V 7 FL_RESET 6 DGND_FL 5 DGND_FL 4 LED_MUTE 3 LED_BT 2 LED_PW 1 E4V 1 DGND 2 KEY0 (Page 49) 3 KEY1 >06S 4 KEY2 5 DGND JL1023 JL1024 R1106 100 FB1002 C1025 0.1 D1006 DA2J10400L E3.3V 2 JL1020 RFDET_NFC JL1013 1 C1203 1000p C1204 1000p C1205 1000p C1206 1000p C1207 1000p JL1028 JL1026 3 R1077 100k C1015 1 R1081 22k R1078 100 1 2 3 R1085 2.7k R1083 3.3k C1020 4700p C1019 1 GND 4 0 0 2 R1082 100k 0 1 0 2 GND IC1007 TC7SH02FU(T5RSOYJF) GND IC1006 TC7WHU04FK(T5RSOYF CE SWITCHING IC1005 MM3411A33URE 1 4 VDD IC1007 IO BOARD CN251 0 5 OSC CL1210 C1016 100 10V 5 +3.3V REGULATOR E C1008 10 0 0 6 >04S 3.2 7 VDD IC1006 0 0 0 0 8 0 D VIN IC1005 3 VOUT 4 C 4 (Page 47) JL1025 R1099 1k NFC1 NFC (RC-S801/A) C1208 1000p CN1004 3P L1001 2.2uH FFC5 C1028 10 C1023 0.1 JL1017 SIRCS PCONT_IR F FB1003 R1070 47k R1073 10k CL1207 CL1014 C1009 0.22 Q1002 LSCR523UBFS8TL G 3.2 SIRCS RESET SWITCH FL_CLK R1072 47k >114S D1005 DA2J10100L MAIN BOARD (7/7) R1071 100k C1010 0.01 E4V E12V FL8V FB1007 R1094 100k D1008 DA2J10100L R1074 0 R1088 100 JL1016 FB1005 C1029 100p JL1030 FL_CS JL1031 FL_DATA R1090 100 JL1032 C1030 100p CL1015 1k KEY1 R1092 1k LED_MUTE R1117 100 JL1047 TP_LED R1116 100 JL1051 JL1048 JL1038 R1118 100 FB1006 7.6 6 R1076 33k C1012 0.01 GND OUT 4 2 VDD Cd 3 7.4 JL1034 JL1033 3.6 L1002 2.2uH 3 C1021 0.1 ET1001 C1026 0.1 ET1002 2 1 (CHASSIS) (CHASSIS) HT-ST7 40 40 >05S DISPLAY BOARD CN801 CN1007 5P C1014 0.022 4 (Page 49) JL1011 JL1035 1 FFC6 FB1008 E MAIN BOARD (5/7) JL1049 VOLTAGE DETECT IC1004 PST8429UL 7 5 JL1037 R1093 E >113S JL1036 KEY0 R1091 1k IC1004 D1003 DA2J10100L (Page 39) R1115 100 LED_PW D1007 DB2S31100K8 JL1029 100 KEY2 R1075 33k J C1027 0.1 0 (Page 41) I R1087 100 R1089 FL_RESET H CN1005 15P JL1015 FFC7 KEY BOARD CN751 HT-ST7 4-11. SCHEMATIC DIAGRAM - MAIN Board (7/7) - 1 A 2 • See page 52 for Waveforms. • See page 52 for IC Block Diagrams. 3 4 5 6 7 8 9 10 11 12 MAIN BOARD (7/7) (Page 35) >103S MAIN BOARD (1/7) E4V HDMI1.3V DGND FB601 JL604 L601 2.2uH C609 0.1 E12V L606 10uH L604 10uH L603 2.2uH FB602 JL606 L611 10uH FB603 C617 0.1 R605 0 B (Page 36) 12V 2 GND 3 GND 4 AGND 5 JL602 C602 10 8.8 BOOT 3.5 SS SW EN R607 100k R610 15k C607 0.01 C614 0.01 C620 10 C623 10 R611 1k R608 22k C613 47 25V C645 10 C601 47 25V C605 10 C616 0.022 C619 0.1 C622 22 C625 22 JL605 DGND R602 1k R613 470 PCON_DSP NC 8 VIN R631 33k 4 3.2 IC605 RT8293ALZSP 7 VOUT 8 IC604 +3.3V REGULATOR IC604 BD00IC0WEFJ-E2 6 4 3 2 1 3.3 BOOT 7 IC605 DC/DC CONVERTER 3.5 6 5 NC VIN 12.6 SW 5 3.2 SS GND EN 1 0.8 3.5 3.2 0.9 0.8 R612 3.3k 2 COMP 8 3 FB 7 4 1.1 BOOT SS 6 VIN 5 SW DC/DC CONVERTER IC602 RT8293ALZSP GND IC602 EN 1 15.1 8.1 5.8 15.1 1.1 10 COMP 2 L612 10uH R629 0 FB 3 L608 10uH C638 0.1 R632 10k SW3.3V R604 4.7k PCON3 R628 4.7k R623 47k JL607 C608 0.01 C615 0.01 C621 10 C624 10 R614 10k C646 10 C649 22 C636 10 C637 0.01 R627 1k (Page 40) HT-ST7 C626 1 JL608 L607 2.2uH L605 10uH C610 0.1 PCON_HDMI H I C651 10 FB L602 2.2uH C603 10 MAIN BOARD (6/7) C647 22 GND SW3.3V PCON1 >114S R617 3.3k DGND DSP1.1V 4 MAIN BOARD (5/7) 4.4 R616 10k R609 10k F >112S COMP GND R601 1k 8 (Page 39) R615 3.3k JL609 R606 0 G 8 0.8 MAIN BOARD (3/7) 7 EN E 6 JL601 R603 4.7k >107S 5 1 8 D (Page 37) IC603 DC/DC CONVERTER IC603 RT8252ALGSP 0.8 SS 7 1 FB BOOT EN 6 2 VIN 4 5.9 VIN 15.1 SW 5 IC601 RT8293ALZSP 3 NC POWER BOARD CN503 1 IC601 DC/DC CONVERTER 3.5 >07S 12V 1 0.8 JL603 (Page 51) 2 3.2 CN601 5P 3 COMP C 4 4 GND 1.3 AGND DGND 9 15.1 7 FB MAIN BOARD (2/7) E4V E12V 1.9 >104S FL8V E12V E4V 41 41 C640 0.01 R621 1k C643 10 C644 10 R633 4.7k C648 10 C650 22 R622 15k C629 1 C628 1 HT-ST7 4-12. PRINTED WIRING BOARD - MAIN Board - • See page 34 for Circuit Boards Location. • 4 5 6 7 8 C625 L606 C605 L603 R5009 >07P POWER BOARD CN503 5 C IC5101 CN5002 4 5 R5511 4 1 R5510 R5509 C5502 R5508 5 8 R5507 R5101 R5102 R5506 C5105 Q5001 R5517 C5501 R5103 C5503 C5043 16 9 27 28 IC5102 E FFC3 >02P AMP BOARD CN3001 (Page 43) 1 3 C5041 E 1 IC5001 1 132 R5075 R5069 R5068 R5062 176 RB5002 K IC1005 1 R1077 R1078 R1087 1 2 R1106 C1208 3 C1019 R1095 R1099 5 8 5 1 R1096 4 1 L604 3 R3722 5 C607 4 C645 CN3501 3 IC37044 C3568 JL3519 C3569 C3727 C3728 R3723 8 1R3724 19 JL3517 (US, CND, AUS) R1013 IC9054 R1047 50 76 C1006 R1021 1 IC904 37 5 C912 C904 25 36 C941 C940 L906 C906 L905 R3632 R951 R950 48 C922 C921 R938 C916 R931 24 3 1 R954 75 12 5 R3734 4 C3731 FB3506 3 C3730 1 R3737 JL3513 X901 C5018 1 5 27 3 R976 C5016 E R1091 IC5500 ET1002 ET5000 R1092 CN3503 JL3532 1 JL3535 1 19 133 R3629 176 R3636 C3559 C3553 C3552 15 R922 IC901 1 R909 1 14 R913 2 2 CN902 8 1 1 2 9 CN3200 HDMI OUT TV ARC C903 R915 CN901 FB1006 1 4 1 R3624 R3618 132 FB3503 R3621 R930 R929 R923 R1093 5 CN1007 IC3506 C933 R974 C1202 R1236 FB1001 JL1061 FB5002 R1235 R1232 C5500 2 12 C1201 8 5 R1231 13 1 R5500 R5501 1 4 L5504 CN1001 R5502 44 X3501 C945 1 45 R3625 C3549 28 4 IC908 HDMI IN C3528 C3550 C907 L907 C5008 88 JL3516 R925 C946 RB5000 2 19 89 JL3533 IC5000 CN3502 R3579 JL3515 R3599 L902 FL5000 1 R3619 C3551 R908 R960 R959 R958 13 R957 R956 R955 C1002 R1012 R1011 R1010 IC1002 51 R968 R961 R967 R1004 R1045 R1048 FB3504 C1003 R1014 100 R1239 C5071 GS R1046 26 R1237 R1069 R1068 R1240 R5040 R5043 R5045 R5047 5 X1001 28 RB5001 C5007 C3567 C3725 JL3534 C5009 ET3501 5 C3566 8 RB5003 C5012 C5014 1 C1206 IC601 C602 IC1007 IC1006 R1083 R1085 1 4 CN1002 8 2 C1207 7 1 R1102 FB1002 C1205 C614 R1104 C1025 8 R1101 R601 C1203 R603 9 C1020 R1034 R1033 C1007 1 25 R1238 54 FB5000 8 R5027 R5030 KA R1008 X5000 R5036 R5039 R5042 R5044 R5046 R5049 R5054 R5055 R5057 C5056 R5061R5060 4 3 C1015 IC1001 C1001 4 R1041 D1003 D D1008 C5505 R5037 C5048 C5050 IC5105 R5108 FB5003 Q5002 D R5013 133 C5062 R5063 1 K A R5011 R5012 R5014 R5015 R5017 R5021 R5028 R5513 R5031 C5506 44 C5042 R5026 C5046 R5029 R1116 D1006 C1028 CN1005 CN1006 C1008 45 C5030 89 R5025 C613 L1002 A R5514 CN601 R5016 R5018 R5019 R5020 R5022 R5023 R5024 3 1 C1016 L612 C5070 C5058 88 1 (Page 50) C5059 C1021 FB1008 R5008 C5047 FB602 C622 4 R5005 R5004 R5003 C5025 C5024 C5023 1 C601 B C648 C650 C649 FL5002 L1001 15 13 (CHASSIS) FFC5 1 12 NFC1 NFC (RC-S801/A) (NC) CN1004 14 2 1 11 R3510 R3503 R3505 R3502 R3504 R3501 C5055 5 R1088 R1090 C1026 R1081 R1082 C608 FB603 R1117 R1118 R1020 R1029 R1027 R1025 R1023 L611 L608 4 C1029 FB1007 C640 R627 R628 C637 8 C1030 R1089 C626 C647 ET1001 5 IC605 Q1001 IC603 4 L605 1 R1039 C619 1 8 C651 C636 C615 R602 R604 8 C643 5 8 1 C646 R608 (CHASSIS) IC602 C603 R622 C5051 R5052 FFC6 C644 C5052 4 C621 C624 IC604 5 C616 R623 C628 C629 ET5001 (CHASSIS) IO BOARD CN251 >04P FB1005 C1027 FB1003 MAIN BOARD (SIDE A) A DISPLAY BOARD CN801 >05P 10 (Page 46) X1001 (Page 48) 9 IC6005 3 C620 C623 2 C1023 1 : Uses unleaded solder. L903 13 14 ET3500 JL3225 19 C902 (CHASSIS) FB902 11 FFC4 FFC7 IO BOARD CN4001 >03P (CHASSIS) (Page 46) FFC2 KEY BOARD CN751 (Page 48) FFC1 IO BOARD CN201 >01P (Page 46) JL1053 JL936 JL906 JL908 JL902 C934 JL1058 JL1055 CL1008 C5002 JL5501 K C5037 C5019 C5035 C5022 C5020 C5034 C5032 C5036 C5029 JL5034 C5028 C5027 JL5036 JL5030 JL5035 FB601 R5035 C5044 C5040 C5038 JL5003 C5033 C5031 C617 C5026 JL5032 JL5031 C5017 JL5005 JL5006 4 R5059 R5058 R5053 1 R5056 R1094 JL5007 JL5008 CL5006 L607 IC1004 JL1013 2 1 A CL1009 K 3 4 D1007 R1073 C1010 C1014 R1072 R1028 R1070 R949 FB903 CL908 CL907 CL909 CL917 R1018 C610 R3620 CL1003JL607 R1038 CL1014 R1006 R1007 A E Q1002 CL1002 CL1210 R1040 K A/K A CL916 JL1038 R633 JL1048 R629 JL1049 JL1031 JL1015 JL1051 JL1032 L601 JL1029 JL1025 R3732 R3593 JL1030 JL1016 JL1017 1 R3376 C3733 E R3644 R3606 Q1004 R3727 C3554 C3562 R3728 R3731 R3730 R3729 C3545 R3643 C3544 C3543 C3542 C3534 C3529 R3588 R3590 R3591 R3576 R3578 R3589C3519 C3526 R3573 C3520 R3598 R3597 C3518 C3525 C3523 R3584 R3583 R3585 R3506 R3507 R3523 R3517 R3516 JL3528 C3560 R3640 R609 JL1044 JL1042 L3500 R605 JL1043 JL1041 FB3505 R610 R611 C609 JL1040 JL1026 JL1039 JL1047 JL1036 R606 R943 C918 C923 C924 C3555 C3548 C3546 R3626 R3627 R3628 C3540 JL604 JL1028 R632 C638 K 5 R3377 R3622 R631 R613 R614 C920 D901 R3739 3 R3645 C3564 C3557 R3646 C3565 C3558 R3623 C3533 C3541 R3600 R3602 R3601 C3516 R918 R916 R921 C919 CL924 CL915 CL919 CL922 R907 R904 R963 R906 CL918 CL920 CL921 CL923 R903 CL925 R905 R902 R901 R964 CL926 R1026 JL608 R612 CL5005 L602 C1012 R1076 R1075 R1065 R1107 CL1004 R1037 CL1011 CL1010 C1005CL1006 JL928 C911 C917 R1001 R1002 R1003 JL1037 JL605 R616 R621 JL5001 CL1209 JL606 R615 R617 JL5009 JL5010 R5081 5 R5080 R5082 R5084 JL5000 R5078 8 CL5003 C5074 R5079 C5021 A K D5001 CL5002 CL5007 FB5001 C5076 CL5001 CL5008 FL5003 R607 R3616 JL932 R920 JL930 R924 R1097 JL603 JL5101 JL5043 JL5038 JL5039 JL5040 JL5041 JL5042 JL5037 JL5013 CL5000 D1004 C5045 C5039 C908 4 C3358 IC6004 R3637 D1005 JL601 A C5053 R926 JL934 R927 R933 R934 JL933 R1030 A R1115 A R1017 R1031 R1059 R1055 R1058 R1022 R1049 R1050 R1051 JL1027 R1052 R1042 R1032 JL1001 D1001 K D1002 K R1062 R1060 R1063 R1064 R1061 R1053 R1054 CL1207 CL1015 R5051 R5048 JL5002 JL602 I C5049 JL935 R3741 C905 JL937 JL929 JL931 R1016 R1015 C5057 JL5004 R5072 R5041 R5038 JL5519 JL5023 R5074 R1071 JL5500 C5064 R1074 JL5517 C5060 C5054 1 2 C913 R973 C3732 R5065 R5066 C5066 IC5002 JL5518 JL5516 C5072 IC902 JL909 C1009 JL5021 C5068 R5531 C5065 JL5514 JL5513 JL5515 JL5024 4 3 JL927 JL921 JL923 JL910 R5516 R5515 JL5508 R5007 JL5511 JL5512 R5525 JL5020 C5067 R5527 JL5506 JL5509 RB5005 JL5510 R5064 R5070 JL5502 JL5504 JL940 C5006 R5067 JL5022 C5061 C5069 RB5004 JL5505 JL5507 R5523 JL5503 2 R3387 R3365 C901 R919 C5003 R5000 C5005 1 C5004 R5001 C5000 C5001 JL918 JL922 R912 R914 C932 R965 JL938 G J FB901 IC906 3 4 R3386 R3733 R3370 R3372 C3364 R3373 JL904 JL1011 JL1034 JL3228 JL926 JL925 JL917 C3563 R911 JL905 JL901 C3536 C3538 JL1035 C3532 JL1033 JL1054 C3527 JL609 JL1056 JL1059 JL1057 JL1012 JL907 JL919 JL924 R910 JL903 R928 JL1052 C914 R1234 R1233 R3374 C3363 R3380 MAIN BOARD (SIDE B) JL1007 H 1-888-221- (11) (CHASSIS) BT1 Bluetooth MODULE R3725 R3726 C3729 F >06P R1098 JL1045 JL1021 R1103 R1105 JL1020 JL1018 JL1022 JL1019 JL1023 JL1046 JL3520 R3508 R3509 R3524 R3519 R3518 JL1014 C1204 11 JL1024 1-888-221- HT-ST7 Note 1: When IC1002 on the MAIN board is replaced, refer to “ABOUT THE PAIRING METHOD” on page 4. 42 42 (11) Note 2: IC3506 on the MAIN board cannot exchange with single. When this part is damaged, exchange the complete mounted board. HT-ST7 4-13. PRINTED WIRING BOARD - AMP Board - • See page 34 for Circuit Boards Location. • 3 5 Q3003 – 3009 2C 2E 1B 2B 1E 1C CL3068 9 F3004 C3168 Q3008 C3196 R3007 F3006 CAM302 CAM309 R3001 E R3004 R3002 Q3001 C3002 F3005 CL3054 CL3053 F3008 F3007 F3002 C3204 CL3052 C3193 CL3051 C3188 D3001 F3003 CAM307 D3002 R3083 C3135 Q3009 C3174 RB3006 Q3006 Q3005 (CHASSIS) R3112 R3109 C3118 Q3007 C3089 C3081 C3048 C3034 C3028 C3039 C3057 10 (CHASSIS) RB3005 R3084 C3115 R3137 CL3011 CL3012 CAM301 8 (CHASSIS) RB3004 R3052 C3058 R3047 Q3004 CL3024 CL3023 CL3020 CL3019 Q3003 (CHASSIS) 7 C3143 (CHASSIS) C3007 R3009 R3138 CAM308 6 C3151 AMP BOARD (COMPONENT SIDE) A 4 C3140 2 CL3018 CL3017 CL3015 CL3014 1 : Uses unleaded solder. B R3026 CL3069 R3017 R3019 R3022 CN3001 2 1 RB3002 FB3002 R3136 R3135 R3134 C3020 C3027 C3044 C3049 C C3014 CAM310 IC3001 44 C3023 C3060 C3067 C3078 C3096 C3104 23 44 22 1 IC3003 C3119 C3110 C3128 C3134 C3148 C3154 IC3005 ET3005 CAM312 23 44 C3165 C3169 C3180 C3187 C3201 C3206 23 44 22 1 IC3007 C3212 R3021 R3018 23 FFC3 R3014 RB3001 ET3004 >02P (Page 42) 27 28 FB3001 MAIN BOARD CN5002 (CHASSIS) (CHASSIS) R3050 R3051 CAM313 R3122 R3123 R3116 R3117 ET3003 22 R3096 R3097 R3090 R3091 R3049 R3056 R3058 R3036 R3038 ET3001 1 CAM311 22 R3028 R3030 R3048 1 C3221 CAM303 CAM305 56 C3071 C3219 29 (CHASSIS) R3080 R3143 1 R3057 C3074 C3070 28 C3079 R3073 R3059 C3084 C3085 C3099 (CHASSIS) CAM306 IC3004 11 1-888-222- (11) C3116 C3117 D C3069 R3141 (CHASSIS) (CHASSIS) (CHASSIS) E AMP BOARD (CONDUCTOR SIDE) C3102 C3100 R3064 R3066 CL3050 C3075 L3011 C3080 C3113 CL3056 R3077 R3078 C3114 CL3025 R3079 R3081 R3065 C3101 R3045 JL3029 C3012 IC3008 C3026 R3020 C3077 R3074 JL3037 C3062 C3038 R3053 C3056 C3013 5 C3015 C3054 JL3056 R3040 C3214 G L3006 R3044 R3086 L3007 C3166 C3120 R3068 C3122 C3164 L3014 R3087 R3099 R3093 C3171 C3184 C3152 C3131 L3013 R3072 C3083 C3195 C3183 C3103 C3063 C3109 C3186 R3113 C3130 C3111 R3061 C3043 JL3048 C3061 C3073 C3047 R3054 R3130 JL3061 C3172 C3142 C3072 C3055 1 C3133 R3104 JL3047 C3121 C3091 L3019 R3103 L3022 R3125 R3119 JL3008 L3027 R3129 C3059 C3190 C3137 C3095 C3205 C3211 C3175 R3114 JL3003 JL3014 C3213 C3147 C3200 >08P H R3041 POWER BOARD CN502 JL3053 1 CN3004 C3097 C3088 C3129 C3107 C3149 C3139 C3157 R3043 C3040 C3046 C3051 R3069 C3064 R3055 C3087 C3076 R3060 R3071 C3093 C3098 C3106 C3125 R3070 R3094 R3100 R3102 C3138 C3145 R3092 C3132 C3150 R3089 JL3050 CL3009 R3042 R3039 R3063 R3062 R3095 R3067 R3098 CL3080 JL3025 JL3026 JL3027 JL3028 CL3013 C3178 R3120 JL3018 R3101 6 CN3003 1 JL3036 CL3037 C3203 JL3058 JL3046 4 CN3002 1 CL3076 JL3057 2 1 CN3006 SPC3 SPC1 SP8 SURROUND BACK R-CH R3127 JL3059 JL3060 CL3078 CL3081 3 CN3007 1 11 MOUNTED BOARD SP6 SP5 SURROUND SURROUND R-CH L-CH SP1 TWEETER (FRONT L-CH) 43 43 (11) SPC2 MOUNTED BOARD SP7 SURROUND BACK L-CH C3208 1-888-222- I SP9 (CENTER) JL3019 JL3021 JL3023 C3209 R3124 R3121 C3185 CL3016 JL3043 JL3044 JL3045 SPC4 HT-ST7 R3075JL3013 R3118 R3126 R3115 R3128 C3191 C3197 C3156 JL3035 CL3022 C3202 C3068 C3052 C3192 (Page 50) C3045 JL3052 C3181 R3105 5 JL3007 JL3016 JL3015 JL3022 JL3010 R3029 C3163 JL3005 JL3012 JL3020 JL3054 JL3006 JL3017 CL3048 JL3024 F CL3058 SP3 WOOFER (FRONT L-CH) SP2 TWEETER (FRONT R-CH) SP4 WOOFER (FRONT R-CH) Note: When the IC3001, IC3003, IC3005 and IC3007 on the AMP board are replaced, refer to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on page 4. HT-ST7 4-14. SCHEMATIC DIAGRAM - AMP Board (1/2) - • See page 52 for IC Block Diagrams. 1 3 2 4 6 5 7 8 9 10 12 11 13 14 15 17 16 18 19 20 AMP BOARD (1/2) A CN3003 6P SPC4 JL3036 B SP8 SURROUND BACK R-CH CH3+(SBR) 1 CH3– 2 SP7 SURROUND BACK L-CH CH5+(SBL) 3 CH5– 4 CH4– 5 CH4(C)+ 6 SP9 (CENTER) JL3035 JL3028 JL3027 JL3026 JL3025 CL3022 CL3013 CL3037 CL3016 11 C3028 0.001 C3034 0.001 C3048 0.001 C3039 0.001 CAM301 (CHASSIS) C3089 0.001 12 13 RB3004 100k R3047 100k C3057 2.2 C3081 0.001 14 15 R3137 100k 16 CL3018 CL3017 R3009 100k C3007 2.2 C 12.6 12.6 ET3001 -2 0 12.6 -1 12.6 R3138 100k 12.6 Q3003 0 HN1A01FU-TE85R DC DETECT 12.6 -2 CL3011 12.6 12.6 -1 12.6 Q3004 0 HN1A01FU-TE85R DC DETECT 0 12.6 -2 -1 17 18 CL3015 CL3014 19 12.6 20 Q3005 0 HN1A01FU-TE85R DC DETECT 0 (Page 45) >121S AMP BOARD (2/2) 21 22 23 E CAM310 12.6 R3052 100k C3058 2.2 CL3012 24 (CHASSIS) (CHASSIS) (CHASSIS) E (CHASSIS) CAM312 CAM313 25 ET3005 E 26 R3001 0 ET3003 R3039 0 R3042 0 R3062 0 R3063 0 R3067 0 C3087 1000p C3093 1000p R3070 0 E D CAM311 ET3004 D3001 DA2J10100L C3002 0.1 E (CHASSIS) CAM303 R3002 100k CL3009 C3040 1000p D3002 DZ2J140M0L 0 CAM308 R3007 15k CL3081 3.2 (CHASSIS) Q3001 LSCR523UBFS8TL BUFFER R3004 10k F R3041 3.3 R3043 3.3 C3045 1 C3052 1 C3051 1000p C3064 1000p R3055 3.3 R3060 3.3 C3068 1 C3088 1 F3002 5A 32V F3003 5A 32V F3004 5A 32V C3046 560 35V C3076 560 35V C3098 560 35V L3006 10uH L3007 10uH 2 4 2 R3069 3.3 R3071 3.3 C3097 1 C3107 1 C3106 1000p L3013 10uH 4 2 C3221 0.47 4 R3143 4.7 R3141 4.7 C3219 0.47 CAM305 CL3025 1 3 1 3 1 3 CAM306 CL3058 G C3043 1000p R3040 3.3 C3047 1000p R3044 3.3 C3073 1000p R3054 3.3 C3083 1000p R3061 3.3 C3095 1000p R3068 3.3 C3103 1000p (CHASSIS) IC3004 R3072 3.3 C3117 10 STREAM PROCESSOR C3067 1 C3056 0.1 C3078 1 C3096 1 C3061 0.1 IC3004 TAS5538DGGR C3104 1 29 SDOUT C3109 0.1 C3013 0.1 H C3049 1 C3063 0.1 C3044 1 C3054 0.1 C3027 1 C3015 0.1 C3020 1 VR_DIG 30 SCLKO C3111 0.1 C3014 0.1 12 24.1 20 21 GVDD_C GVDD_D NC BST_D VDD 19 R3080 10k C3114 0.1 C3023 0.1 C3060 0.1 C3091 1 R3053 22k R3074 0 C3055 0.1 R3078 10 C3062 0.1 C3077 10 C3072 0.1 C3110 0.1 K L FFC3 >02S MAIN BOARD (4/7) CN5002 (Page 38) M N HT-ST7 D3.3V 28 AMP_SCL 27 D3.3V 26 AMP_SDA 25 DGND 24 AMP_PDN 23 AMP_ERR 22 DC_PRT 21 DRIVER_SD 20 AMP_INIT 19 DRIVER_RST 18 AMP_MUTE 17 DGND 16 AMP_MCK 15 DGND 14 AMP_BCK 13 DGND 12 AMP_LRCK 11 DGND 10 AMP_D1(FL/FR) 9 DGND 8 AMP_D3(C/SW) 7 DGND 6 AMP_D2(SL/SR) 5 DGND 4 AMP_D4(SRB) 3 DGND 2 Pcon2 1 JL3003 JL3005 FB3001 R3028 22 R3030 22 R3036 22 R3038 22 R3056 22 R3058 22 SCL JL3006 JL3007 R3048 0 JL3008 R3049 0 R3050 0 C3075 10 JL3012 JL3013 RESET JL3015 MUTE 1.6 JL3017 R3017 47 JL3018 R3018 47 JL3019 R3019 47 JL3020 R3021 47 JL3021 R3022 47 JL3022 JL3023 R3026 47 RB3002 100 C3071 0.1 MCK D1 PDN 18 3.2 3.2 VACS_1 42 PWM_M_3 15 DVDD2_CORE 14 PWM_P_3 DVSS2_CORE 44 PWM_M_4 13 1.6 OSC_RES 45 PWM_P_4 12 1.6 R3075 0 RESET CL3050 L3011 4.7uH 3.2 C3099 0.1 C3102 10 C3100 10 R3066 18k 1.7 R3065 0 ASEL_VACS2 47 PWM_P_7 10 0 R3064 15k AVDD 48 PWM_M_8 9 3.3 VR_ANA PWM_P_8 8 49 3.3 PDN R3073 10k 0 46 MCLK 11 PWM_M_7 PLL_FLTP 50 AVDD_PWM 7 PLL_FLTM 51 AVSS_PWM 6 52 AVSS VR_PWM 5 53 PWM_HPP_R PWM_M_5 4 54 PWM_HPM_R PWM_P_5 3 PWM_HPP_L 55 PWM_M_6 2 PWM_HPM_L PWM_P_6 1 56 SCL SDA RESET 41 PWM_P_2 16 43 LRCK R3079 0 MUTE 1.6 1.6 BCK 3.2 1.6 1.6 C3080 0.1 39 PWM_P_1 D1 R3081 0 2.6 3.2 1.6 LRCK 20 HP_SEL 17 40 PWM_M_2 1.6 BCK SDA VALID MUTE 38 PWM_M_1 19 1.6 1.8 R3014 47 37 D2 0 2.6 JL3014 JL3016 D3 0 1.6 C3069 0.1 R3051 0 24 D4 0 SCL 36 DVSS1_CORE 21 RB3001 100 JL3010 25 0 LRCK 35 DVDD1_CORE 22 1.6 PDN SDIN1 26 3.2 1.6 SDA SDIN2 27 1.6 1.6 CN3001 28P SDIN3 SCLK 23 34 BKND_ERR 3.3 R3077 0 SDIN4 C3116 0.1 1.8 3.2 1.6 C3038 1 R3020 22k C3026 10 33 PSVC CL3056 22 JL3037 C3012 0.1 32 TEST C3113 10 23 12 18 25.5 25.5 17 24 12 16 25 NC 15 PVDD_D 14 26 NC 12.8 13 PWM_D PVDD_D 12 27 1.6 PWM_C GND_D M1 11 28 RESET_CD OUT_D M2 10 1.6 M3 9 3.2 8 3.2 VREG OUT_C 29 GND_C 30 3.3 12.8 24 24 25.5 25.5 PVDD_C 31 AGND BST_B 32 BST_C 33 GND OUT_B 34 OC_ADJ GND_B 35 PWM_B 7 1.1 6 36 1.6 5 37 PVDD_B 12.8 12.8 OUT_A 4 3.3 PWM_A 3 1.6 2 3.2 38 RESET_AB GND_A 39 SD PVDD_A NC PVDD_A 40 NC BST_A 41 NC 1 25.5 25.5 24.1 12 22 GVDD_B GVDD_A IC3003 CXD9981TN 42 12 21 IC3003 DIGITAL POWER AMP 43 OTW 12 24.1 BST_D VDD 20 44 GVDD_C GVDD_D 25.5 19 23 12 18 NC 25.5 17 24 12 16 PVDD_D 15 25 NC 14 26 NC 12.7 13 PWM_D PVDD_D PWM_C GND_D M1 12 27 RESET_CD OUT_D M2 11 1.6 M3 10 3.2 VREG 9 3.2 8 28 1.6 29 3.3 12.8 30 AGND OUT_C PVDD_C 31 GND_C 25.5 11.3 25.5 10.3 24 32 GND BST_B 33 BST_C 34 OC_ADJ OUT_B GND_B 35 PWM_B 7 36 1.1 6 37 PVDD_B 10.2 OUT_A PWM_A 5 RESET_AB GND_A 25.5 SD 4 38 3.3 NC PVDD_A NC 3 3.2 2 R3045 0 J 39 NC BST_A 40 PVDD_A 11.3 12 12 1 41 OTW I 42 JL3029 IC3001 43 GVDD_B GVDD_A 44 DIGITAL POWER AMP IC3001 CXD9981TN 25.5 31 LRCLKO 28 (CHASSIS) R3059 470 1.8 1.1 MCK C3085 0.1 C3084 4700p 0.6 C3070 4700p C3079 0.047 C3101 0.1 C3074 0.047 R3057 470 C3059 470 35V D3 D2 D4 JL3024 R3029 47 Note: When the IC3001 and IC3003 on the AMP board are replaced, refer to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on page 4. 44 44 HT-ST7 4-15. SCHEMATIC DIAGRAM - AMP Board (2/2) - • See page 52 for IC Block Diagrams. 1 3 2 4 6 5 7 8 9 10 12 11 13 15 14 17 16 19 18 20 AMP BOARD (2/2) A SPC3 CN3002 4P SPC2 CN3007 3P JL3046 SP5 SURROUND L-CH CH2(SL)+ 1 CH2– 2 SP6 SURROUND R-CH CH6– 3 CH6(SR)+ 4 JL3045 JL3060 JL3044 JL3043 JL3059 1 Ch7(FR)+ 2 NC 3 CH7– MOUNTED BOARD CL3076 CL3078 CAM307 B C3135 0.001 (CHASSIS) C3115 2.2 R3083 100k C3118 2.2 R3084 100k C3140 0.001 C3143 0.001 C3151 0.001 C3188 0.001 RB3005 100k C3168 2.2 R3109 100k C3174 2.2 R3112 100k C3193 0.001 C3196 0.001 C3204 0.001 CL3024 CL3054 CL3020 Ch1(FL)+ 18 1 PVDD_S 19 2 PVDD_25V 20 3 PVDD_25V 4 PVDD_GND 5 PVDD_GND Q3007 HN1A01FU-TE85R -2 0 DC DETECT R3094 0 C3139 1 E C3145 1000p R3100 3.3 R3102 3.3 C3149 1 C3157 1 R3120 0 C3178 1000p C3156 1000p C3203 2200 35V L3019 10uH L3022 10uH 4 1 3 1 3 IC3008 C3120 0.1 C3147 1000p C3152 1000p C3148 1 C3154 1 5 4 3 2 1 1 R3099 3.3 R3103 3.3 JL3048 C3134 1 R3093 3.3 C3164 0.1 C3128 1 C3192 1 C3197 1000p C3185 2200 35V 25.5 C3137 1000p C3181 1 C3191 1000p C3150 560 35V 2 SP3 WOOFER (FRONT L-CH) R3127 0 C3132 560 35V C3122 0.1 C3131 1000p R3118 3.3 R3124 0 F3008 5A 32V 24 R3087 3.3 R3115 3.3 R3121 0 F3007 5A 32V 4 SP1 TWEETER (FRONT L-CH) DC DETECT F3006 5A 32V 2 MOUNTED BOARD Q3009 HN1A01FU-TE85R R3101 0 +12V REGULATOR IC3008 SI-3010KM-TLA G 0 F3005 5A 32V L3014 10uH F DC DETECT -1 R3114 3.3 C3184 1000p C3190 1000p C3180 1 C3187 1 4 2 4 1 3 1 3 R3119 3.3 R3125 3.3 CL3048 C3166 0.1 R3126 3.3 R3128 3.3 C3202 1 C3209 1 C3200 1000p C3205 1000p C3201 1 C3206 1 C3208 1000p L3027 10uH 2 C3171 0.1 C3211 0.1 C3129 1 C3138 1000p 0 JL3057 C3175 0.1 R3092 3.3 -2 Q3008 HN1A01FU-TE85R CL3051 12.6 25.5 R3089 3.3 R3098 0 12.6 24 C3125 1000p R3095 0 0 VC D -1 VIN 0 12.6 GND -1 12.6 12.6 3.2 DC DETECT -2 0 12.6 JL3056 Q3006 HN1A01FU-TE85R 12.6 VOUT 0 12.6 25.5 -1 12.6 JL3058 Ch1– -2 CL3019 CL3052 2 12.6 12.6 SPC1 CN3006 2P 1 0 12.6 12.6 ADJ 12.6 (CHASSIS) CL3053 12 12.6 12.6 SP4 WOOFER (FRONT R-CH) CAM302 RB3006 100k CL3023 C CL3080 SP2 TWEETER (FRONT R-CH) R3129 3.3 C3213 0.1 12 24.1 JL3050 JL3052 JL3054 CL3069 C3195 1 22 CL3068 21 JL3061 R3130 0 BST_D 20 GVDD_C GVDD_D VDD 19 23 12 25.5 18 NC 25.5 17 24 12 16 PVDD_D 15 25 NC 14 26 NC 12.8 PWM_C 13 PWM_D PVDD_D M1 GND_D M2 12 27 RESET_CD OUT_D M3 11 1.6 VREG 10 3.2 AGND 9 3.2 GND 8 28 1.6 29 OC_ADJ OUT_C 30 GND_C 31 3.3 12.8 32 PVDD_C 33 BST_C 25.5 24 34 BST_B 35 PWM_B GND_B OUT_B 36 1.1 7 1.6 6 37 PVDD_B 12.8 12.8 OUT_A 5 RESET_AB GND_A PVDD_A PWM_A 4 1.6 SD 3 3.2 38 3.3 25.5 25.5 NC PVDD_A BST_A 2 C3142 1 R3086 22k R3104 0 13 39 NC 1 40 NC 22 41 R3113 22k 12 24.1 12 GVDD_B GVDD_A DIGITAL POWER AMP IC3007 CXD9981TN 42 12 21 43 OTW 12 24.1 BST_D VDD 20 44 IC3007 GVDD_C GVDD_D 25.5 19 23 12 18 NC 25.5 17 24 12 16 PVDD_D 15 25 NC 14 26 NC 12.8 13 PWM_D PVDD_D PWM_C 12 27 1.6 M1 GND_D M2 11 1.6 M3 10 3.2 VREG 9 3.2 AGND 8 28 RESET_CD OUT_D 29 GND OUT_C 30 OC_ADJ BST_C 31 3.3 12.7 32 GND_C 33 BST_B 34 PVDD_C 24 25.5 35 PWM_B GND_B OUT_B 36 1.1 7 1.6 6 37 PVDD_B 12.7 12.8 OUT_A 5 RESET_AB GND_A 4 1.6 3 3.2 38 3.3 25.5 25.5 PWM_A PVDD_A SD PVDD_A NC BST_A 39 JL3047 11 40 2 12 1 41 NC I 42 OTW DIGITAL POWER AMP IC3005 CXD9981TN 43 GVDD_B GVDD_A 44 IC3005 NC 12 24.1 H 14 J C3119 0.1 C3121 0.1 C3133 10 C3130 0.1 C3165 0.1 C3214 1 C3163 1000 35V R3134 10k C3169 0.1 C3172 0.1 C3186 10 C3183 0.1 C3212 0.1 R3105 100k 15 >121S K AMP BOARD (1/2) 16 R3090 22 R3091 22 R3096 22 FB3002 (Page 44) R3097 22 R3116 22 R3117 22 R3122 22 R3123 22 17 R3136 10k CN3004 5P R3135 100k JL3053 21 22 23 L (Page 51) >08S POWER BOARD CN502 CAM309 24 25 (CHASSIS) 26 Note: When the IC3005 and IC3007 on the AMP board are replaced, refer to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on page 4. HT-ST7 45 45 HT-ST7 4-16. PRINTED WIRING BOARD - IO Board - • See page 34 for Circuit Boards Location. 1 2 3 • 4 : Uses unleaded solder. 5 6 7 8 IO BOARD (COMPONENT SIDE) A (CHASSIS) CAM201 C206 E R254 B R208 C202 R252 R251 R253 R205 R203 R209 C203 Q251 C207 R206 R204 R202 CN4002 EZW-RT50/ EZW-RT20 1 30 4 R237 R235 26 C223 C4001 R4004 R4005 15 CN201 9 C4002 R4006 16 8 2 FFC2 CN4001 R4001 R4007 R4002 D >01P R4003 13 12 2 1 R233 MAIN BOARD CN901 L202 (Page 42) 1 C219 C 27 5 RF MODULATOR (EZW-RT50) C230 FFC4 CAM202 1 MAIN BOARD CN1001 >03P 8 5 R225 C215 R228 4 IC205 R224 11 1-888-223- (Page 42) (CHASSIS) (11) IO BOARD (CONDUCTOR SIDE) E J202 COAX JL221 JL205 JL4007 C201 JL4003 JL4014 C263 JL4008 JL4009 JL4002 JL4013 F R201 JL4006 JL223 JL4015 JL225 JL224 DIGITAL IN JL4012 JL4011 JL4010 C204 JL226 JL4001 JL201 IC201 3 OPT 2 2 JL227 JL222 JL4004 1 JL206 JL4005 JL202 1 C205 3 IC202 OPT 1 (TV) 2 G JL228 JL255 JL253 J251 JL251 IR BLASTER JL203 JL252 1 J201 CN251 H >04P JL229 ANALOG IN JL204 MAIN BOARD CN1004 R (Page 42) Note: When the RF modulator (EZW-RT50) is exchanged, refer to “SETTING METHOD OF THR WIRELESS CONNECTION on page 4. HT-ST7 L 4 11 1-888-223- 46 46 (11) HT-ST7 4-17. SCHEMATIC DIAGRAM - IO Board - 1 2 3 4 5 6 7 8 IO BOARD JL205 COAX L202 220uH C201 10 JL221 3.2 IC201 OPTICAL RECEIVER VCC DIGITAL IN OPT 2 OUT GND C263 470p 8 3.2 1 7 IC205 2 3 R224 470 IC202 JSR1124 C OUT GND WAVE SHAPER IC205 TC7WHU04FU(TE12R) R225 10k C215 2p 2 3 R228 220k JL202 0 2 CN201 9P C223 0.1 3.2 1 4 2.7 1.6 IC202 OPTICAL RECEIVER VCC 5 JL201 0 1 OPT 1 (TV) 6 GND B R201 100 VDD IC201 JSR1124 1.5 J202 1P 1.5 A C204 0.1 C205 0.1 C219 1 JL206 C230 100 10V R235 100 3 JL225 JL223 R233 100 JL224 JL226 JL227 J201 2P D R202 0 R203 2.2k R237 100 C206 10 R205 10k JL228 JL204 R JL222 C202 220p R208 33k JL229 ANALOG IN JL203 L R204 2.2k C203 220p R206 10k R209 33k C207 10 COAX 4 OPT_SAT 5 OPT_TV 6 DGND 7 LINE-L 8 AGND_DIRAD 9 LINE-R 30 LRCK_Z 29 BCK_Z FFC2 >01S MAIN BOARD (2/7) CN901 (Page 36) EZW-RT50/ EZW-RT20 1 DGND 2 WL_BCK 3 28 SDIO_Z DGND 4 27 LRCK_Y WL_D0 5 26 BCK_Y WR_RESET 6 WL_SCL 7 WL_RESERVED 8 WL_SDA 9 (Page 39) >03S MAIN BOARD (5/7) CN1001 JL4008 R4003 0 JL4015 JL4006 JL4007 JL4009 JL4001 R4002 0 JL4002 R4004 220 JL4010 JL4012 WL_INT 10 WL_DET 11 WL_RF 12 SW3.3V 13 J251 JL4011 JL4004 R4007 R4005 220 0 JL4014 JL4013 JL255 IR BLASTER G >04S MAIN BOARD (6/7) CN1004 R253 33 CN251 4P (Page 40) R254 33 JL251 IR4V 1 NC 2 GND 3 REMOTE C4002 0.001 C4001 0.001 R4001 1k R4006 10k JL252 JL253 4 R251 100 Q251 LSCR523UBFS8TL LED DRIVE 0.8 0 R252 10k JL4005 CAM201 (CHASSIS) HT-ST7 SW3.3V 3 WL_LRCK FFC4 I DGND 2 JL4003 E H 1 CN4002 30P CN4001 13P F 9 25 SDIO_Y 24 GND 23 RESET 22 I2CCLK 21 I2CSDA 20 NC 19 PD-OUT_Airoha 18 INT 17 256FS 16 GND 15 GND 14 +3.3V 13 +3.3V 12 GND 11 SDIO_W 10 BCK_W 9 LRCK_W 8 SDIO_X 7 BCK_X 6 LRCK_X 5 NC 4 NC 3 RESERVE 2 DETECT 1 RESERVED RF MODULATOR (EZW-RT50) CAM202 Note: When the RF modulator (EZW-RT50) is exchanged, refer to “SETTING METHOD OF THR WIRELESS CONNECTION on page 4. (CHASSIS) 47 47 HT-ST7 4-18. PRINTED WIRING BOARDS - PANEL Section - 1 2 • See page 34 for Circuit Boards Location. 3 4 5 • : Uses unleaded solder. 6 7 8 9 10 KEY BOARD (SIDE A) DISPLAY BOARD (COMPONENT SIDE) >06P FFC7 12 S751 – 755 (Page 42) A 11 MAIN BOARD CN1007 CN751 5 1 S754 VOLUME + C818 Q805 Q804 E C751 S751 C824 4 R809 5 C807 IC802 C755 R754 11 (11) KEY BOARD (SIDE B) C817 Q803 E JL755 E 15 D801 FFC6 R804 >05P JL751 C806 11 D802 R801 1-888-224- (11) 1-888-224- (11) (Page 42) D804 – 806 A T801 9 D 1 DISPLAY BOARD (CONDUCTOR SIDE) E JL801 JL807 JL803 E T801 JL828 Q801 E Q802 C803 JL824 9 JL829 1 JL811 T801 DC/DC CONVERTER TRANSFORMEER JL809 JL825 JL808 JL826 R802 R803 JL804 C805 JL806 JL802 2 3 1 ND802 FLUORESCENT INDICATOR TUBE JL805 JL812 JL814 JL816 JL818 JL820 38 37 JL810 34 IC801 2 24 JL813 JL815 JL817 JL819 JL821 JL822 JL753 11 1-888-225- C808 C802 MAIN BOARD CN1005 K JL754 L801 CN801 1 JL823 11 HT-ST7 S753 VOLUME – 1-888-225- R805 C F S752 INPUT 3 1 1 JL827 C752 R812 R813 R814 R815 C816 D803 C809 R806 R807 D805 Bluetooth INDICATOR C810 D804 POWER INDICATOR A A D804 D805 K K R817 C819 R816 R818 R808 D806 K A R810 C811 D806 MUTING B C812 C813 C814 C815 R751 S755 BLUETOOTH PAIRING 48 48 (11) HT-ST7 4-19. SCHEMATIC DIAGRAM - PANEL Section 1 2 3 • See page 52 for Waveforms. • See page 52 for IC Block Diagrams. 4 5 6 7 8 9 10 11 12 13 DISPLAY BOARD A C818 0.1 C819 0.1 ND802 DGND 1 KEY0 2 >06S KEY1 3 MAIN BOARD (6/7) CN1007 KEY2 4 DGND 5 FFC7 Q803 LTC023JUBFS8TL Q804 LTC023JUBFS8TL Q805 LTC023JUBFS8TL LED DRIVE LED DRIVE LED DRIVE 8V 8 MAIN BOARD (6/7) CN1005 8V 9 FL_DATA 10 FL_CS 11 FL_CLK 12 DGND 13 SIRCS 14 E3.3V 15 (Page 40) Vout JL823 R808 10 +3.3V REGULATOR C805 10 IC802 MM1836A33NRE JL802 JL803 1 2 3 C810 0.1 JL804 JL805 R805 1k JL806 C816 1 C811 0.1 R809 10 C812 0.01 C813 220p C814 220p C815 220p JL807 JL808 R803 47 JL809 R802 47 C807 1 R801 3.3k R804 33k L801 100uH E C802 100 10V JL811 T801 DC/DC CONVERTER TRANSFORMER JL828 2 C803 0.015 12 G 1 JL829 -0.3 Q801 KTC3552T OSC C808 10 50V 3 11 7.9 C806 4700p 7.9 -0.3 Q802 KTC3552T OSC 11 4 9 5 8 6 7 C809 0.1 R806 100 R807 100 C824 220p 49 49 F1 F1 TestB Data Clock CS Reset OSC TestA JL822 JL821 JL820 JL819 JL818 GND 4 D803 DZ2J056M0L >05S 5 D802 BAV99-215 7 JL801 D801 BAV99-215 6 IC802 JL827 NC DGND_FL FL_RESET FFC6 8 5 3.3 DGND_FL JL826 Vin 4 GND LED_MUTE JL825 CN 3 3 8 E 2 LED_BT 2 R814 100 3 3.2 1 JL824 LED_PW OUT VCC CN801 15P 1 Vdd VH P_GND R813 100 REMOTE CONTROL RECEIVER IC801 PNA4823M02S0 HT-ST7 DGND R815 100 IC801 H R810 47k R812 100 C JL817 2.6 0 JL816 2 0 34 33 32 31 30 29 28 27 26 25 24 JL815 2 0 JL810 B 38 37 R818 100 JL814 MUTING R817 100 JL813 Bluetooth INDICATOR JL812 POWER INDICATOR D806 SML-D12D8WT86SQ F2 D805 CL-194S-HB8SP-SD-T F2 D804 SL-194S-WS-SD-T R816 100 E4V 16 17 18 CN751 5P FLUORESCENT INDICATOR TUBE D 15 KEY BOARD C817 0.1 F 14 2 1 (Page 40) JL751 R751 2.2k JL753 R754 2.2k JL754 JL755 C751 0.1 C752 0.1 C755 0.1 S751 S752 S755 S753 S754 / INPUT BLUETOOTH PAIRING VOLUME – VOLUME + HT-ST7 4-20. PRINTED WIRING BOARD - POWER Board - 1 • See page 34 for Circuit Boards Location. 2 3 • : Uses unleaded solder. 4 5 6 7 8 9 10 POWER BOARD C503 CL507 C513 C520 (CHASSIS) (CHASSIS) D519 R533 C516 (US, CND) FH501 JL501 C519 FH502 3 T501 POWER TRANSFORMER 1 (Page 42) C530 11 C524 C527 R517 C528 C534 JW508 JW501 R518 JL505 L505 8 CAM501 PATTERN SPARK-GAP AC1 (AC IN) D517 CL504 F501 CN501 1 F502 C517 JL508 CL511 D514 >07P JL506 ET502 B ET503 R528 JW507 A MAIN BOARD CN601 5 CN503 L506 C533 1 D511 1 (US, CND) JS501 4 IC501 2 C505 6 ET501 CL501 C504 CL502 C511 C508 C512 JS502 (US, CND) D504 50 50 D502 R523 K E D508 (US, CND) C537 1 Q501 CL509 R522 D518 CL510 JW504 R526 18 (Page 43) >08P AMP BOARD CN3004 D521 A502 D516 A PH502 1 R535 R531 D512 JW505 R521 R519 D501 (CHASSIS) HT-ST7 R515 D507 C507 R520 C514 D 7 CL505 R501 R516 2 JW506 R502 - L502 LINE FILTER (AEP, UK, AUS) CL503 JL507 JW509 JL504 R548 R538 R545 R534 C L501 LINE FILTER C522 (US, CND) D513 E VDR501 CL506 C515 C CL508 C509 R525 JL502 A501 + TH501 JL503 JW502 3 C501 C526 R544 C525 CL515 R540 CL514 IC502 3 2 4 R541 R543 C535 1 5 CN502 R542 JW503 11 1-888-226- (11) HT-ST7 4-21. SCHEMATIC DIAGRAM - POWER Board - 2 1 • See page 52 for IC Block Diagrams. 3 4 5 6 7 2 NEUTRAL 3 JL502 CAM501 PATTERN SPARK-GAP B 13 3 4 2 1 3 4 2 1 TH501 C508 D511 D3SB60F3 1 ~ 4 VDR501 3 ~ 2 CL501 JS501 ET502 C503 C513 470p 250V (US, CND) 220p 250V (AEP, UK, AUS) C516 470p 250V (US, CND) CL507 E (CHASSIS) C519 390 200V (US, CND) 130 450V (AEP, UK, AUS) C513 (CHASSIS) BD FB/OLP GND Vcc/OVP S/GND D 6 5 4 3 2 1 D514 RR264M-400 R517 0.33 2W D513 RR264M-400 R519 4.7 C505 0.1 R518 0.33 2W R528 100k 3W C517 3300p 400V D517 SARS10 C509 560p 1kV D508 DZ2J180M0L 7 12 (US, CND) 6 13 C522 4700p 2kV 2 R541 0 2 12V 3 GND 4 GND 5 AGND 1 PVDD_GND 2 PVDD_GND 3 PVDD_25V 4 PVDD_25V 5 PVDD_S CN502 5P 3 L506 2.2uH 2 17 1 18 R538 1k JL504 R540 220k R543 3.3k R548 1k ET503 (CHASSIS) 23.1 C520 470p 250V R521 47k (US, CND) C514 4700p D518 UDZSUSTE-1730B G CL509 ISOLATOR 4 1 CL510 24.2 23.1 3 51 51 2 2 1 IC502 R544 10k SHUNT REGULATOR IC502 MM1431CURE R542 4.7k PH502 PS2561AL1-1-V-W 0.8 4 R534 1k CL515 R545 33k C535 10 50V >07S MAIN BOARD (7/7) CN601 (Page 45) E C525 0.01 R520 2.2k C512 10 C533 470 35V 15 3 C537 2.2 JL508 E C515 10 D512 DZ2J160M0L R526 100 D504 PTZ-TE25-30B C526 2200 35V JL507 12V CL514 R522 27k C507 100p C534 47 35V C530 0.1 1 R531 4.7 R525 100k C528 330 25V 4 D521 FMX-22SL D507 DZ2J220M0L C527 330 25V 14 K D501 UDZSUSTE-1730B D502 UDZSUSTE-1730B 20.5 C524 330 25V CL511 JL506 1 16 20.7 C511 560 25V (US, CND) 330 25V (AEP, UK, AUS) L505 10uH 11 D516 CMF02 R523 4.7k (Page 41) JL505 8 4 Q501 DSC7003R0L REGULATOR 20 CN503 5P F502 5A 250V T501 POWER TRANSFORMER 5 E A502 (CHASSIS) D519 RK49LF-T1 CL508 CL506 CL505 CL504 CL503 R516 4.7 CL502 R515 0 (CHASSIS) R501 0 R535 0 R533 0.33 1W POWER CONTROL IC501 SYR-6735 (US, CND) STR-Y6766 (AEP, UK, AUS) 265.7 19.9 0.9 7 0.5 NC IC501 C519 D A501 C503, 504 1000p 250V (US, CND) 470p 250V (AEP, UK, AUS) C508 0.1 310V (US, CND) 0.22 310V (AEP, UK, AUS) JS502 C504 E ET501 C501 0.22 310V R502 1.5M 0.5W L502 LINE FILTER 2.4 NC JL503 Vref 1 L501 LINE FILTER NC LIVE F501 T5AH 250V A AC1 (AC IN) HT-ST7 12 11 E JL501 H 10 (AEP, UK, AUS) CN501 3P F 9 POWER BOARD A C 8 >08S AMP BOARD (2/2) CN3004 HT-ST7 • IC Block Diagrams 20 V/DIV, 5 Ps/DIV IC603 1 (BOOT) VA 3.2 Vp-p CURRENT SENSE AMPLIFIER R Q 0 IC605 1 (BOOT) 4.1 Vp-p 324 ns 21.2 Vp-p 4 GND SW 3 IC901 SRC4182 3 Ps 2 V/DIV, 200 ns/DIV 2 VIN IC5001 ok (BCLK_OUT) 1 BOOT 100 mV/DIV, 2 Ps/DIV 10 V/DIV, 2 Ps/DIV LGRP 1 IC5001 ol (LRCLK_OUT) RCKI 2 REFERENCE CLOCK INTERPOLATION FILTERS RE-SAMPLER DECIMATION FILTERS NC 3 SDIN 4 BCKI 5 LRCKI 6 AUDIO INPUT PORT 3.8 Vp-p 20.8 Ps 6 25 BCKO 24 LRCKO 23 SDOUT 22 VDD 21 DGND IC1002 qa (Xout) BYPAS IFMT0 IFMT1 IFMT2 RST MUTE 2.6 Vp-p 125 ns 2 V/DIV, 50 ns/DIV HT-ST7 RATE ESTIMATOR AUDIO OUTPUT PORT VIO 7 DGND 8 2 V/DIV, 10 Ps/DIV 28 MODE2 27 MODE1 26 MODE0 52 52 9 10 11 12 13 14 20 TDMI CONTROL LOGIC 19 18 17 16 15 OFMT0 OFMT1 OWL0 OWL1 RDY 2 3 4 FB GND N.C. VOUT S Q 3.1 Ps 2 V/DIV, 20 ns/DIV 5 FOLDBACK CONTROL 0.1 Vp-p 39.6 ns 4 OSCILLATOR CURRENT COMPARATOR 9 SLOPE COMP + – IC5001 wg (XTAL2) VCC 1 + – 10 V/DIV, 2 Ps/DIV 2 V/DIV, 20 ns/DIV 3 11.4 Ps 2.9 Ps 40.6 ns 0.4V 27.2 Vp-p 19.6 Vp-p 2.4 Vp-p EN COMP FB VA 0.8V UV COMPARATOR INTERNAL REGULATOR SOFT START THERMAL SHUTDOWN – Q801, 802 (Collector) 5 + + + qs 7 6 OVER CURRENT PROTECT VCC + EA + – IC602 1 (BOOT) 2 V/DIV, 5 Ps/DIV 1.2V 8 SHUTDOWN COMPARATOR 10 V/DIV, 2 Ps/DIV 2.7V – 1 V/DIV, 20 ns/DIV 8 6 5 + 3 Ps IC904 r; (XTO) 7 11.4 Ps 36.6 ns IC604, 3704 BD00IC0WEFJ-E2 8 3.7 Vp-p 18.8 Vp-p 1.8 Vp-p 2 qa Q801, 802 (Base) EN 7 IC601 1 (BOOT) + – IC3506 <zzc (XTALOUT) – MAIN Board – IC601, 602, 605 RT8293ALZSP IC603 RT8252ALGSP LOCKOUT COMPARATOR 1 – DISPLAY Board – SS – MAIN Board – VCC N.C. N.C. • Waveforms HT-ST7 IC902, 906, 1005 MM3411A33URE 4 VDD CE 1 BIAS VOLTAGE REFERENCE – + CURRENT LIMIT 3 VOUT GND 2 VDDRX RXIN1 RST RXIN2 RXIN3 RXIN4/ASCKIO RXIN5/ABCKIO RXIN6/ALRCKIO RXIN7/ADIN0 MODE MS/ADR1 MC/SCL IC904 PCM9211PTR 36 35 34 33 32 31 30 29 28 27 26 25 RXIN0 37 RESET & MODE SETTING RXIN2 RXIN3 RXIN4 RXIN5 RXIN6 RXIN7 RXIN8 RXIN9 RXIN10 RXIN11 DTOUT AUXIN0 RXIN1 RXIN0 24 MD1/SDA 23 MD0/ADR0 DIR ANALOG DIVIDER XTI 39 XTO 40 XMCKO DIVIDER OSC PLL FILT 43 VCOM 44 ALL 22 DVDD 21 DGND MAIN OUTPUT PORT 20 19 18 17 REGISTER CLOCK/DATA RECOVERY AUTO DIR ADC AUXIN0 AUXIN1 AUXIN2 ADC CLOCK (SCK/BCK/LRCK) XMCKO (TO MPIO_A & MPO0/1) LOCK DETECTION DIR RXIN7 DOUT SCKO/BCK/LRCK RECOUT1 RECOUT0 DITOUT AUTO DIR ADC AUXIN0 AUXIN1 AUXIN2 POWER SUPPLY AGND 41 VCC 42 POWER SUPPLY RECOUT1 RECOUT0 POWER SUPPLY GNDRX 38 SPI/I2C INTERFACE DIR ANALOG COM. SUPPLY ADC A/D CONVERTER A/D CONVERTER MODE CONTROL 16 MPO1 15 MPO0 DIT AUTO DIR ADC AUXIN0 AUXIN1 A/D CONVERTER ANALOG MPO0/1 SELECTOR SCKO BCK LRCK DOUT AUXOUT AUXIN2 14 MPIO_B3 13 MPIO_B2 MPIO_B SELECTOR AUXIN1 ADC_STANDALONE EXTRA DIR FUNCTIONS MPIO_A SELECTOR MPIO_C SELECTOR 1 2 3 4 5 6 7 8 9 10 11 12 ERROR/INT0 NPCM/INT1 MPIO_A0 MPIO_A1 MPIO_A2 MPIO_A3 MPIO_C0 MPIO_C1 MPIO_C2 MPIO_C3 MPIO_B0 MPIO_B1 SECONDARY BCK/LRCK DIVIDER SELECTOR MPIO_A MPIO_B MPIO_C MPO0 MPO1 VINR 48 ADC SBCK/SLRCK ( TO MPIO_A) VINL 47 RXIN8 RXIN9 RXIN10 RXIN11 AGNDAD 45 VCCAD 46 53 HT-ST7 IC908, 6005 R1191N050B-TR-FE 5 VDD ECO 1 THERMAL PROTECTION VOLTAGE REFERENCE + 4 VOUT SHORT PROTECTION GND 2 PEAK CURRENT PROTECTION REVERSE DETECTOR CE 3 IC1004 PST8429UL GND 1 VREF + – 4 OUT VDD 3 CD 2 IC5101 74LVC1G79GW-125 D 1 C TG TG TG _ C 2 _ C _ C GND 3 54 C _ C 16 VCC 1 SELECT 11 C C CP IC5105 TC74VHC157FT (EKJ) 5 VCC TG 1B 3 1B 4A 14 4A OUTPUT 1Y 4 1Y 4B 13 4B 2A 5 2A 4Y 12 4Y OUTPUT 11 2B 6 2B 3A 11 3A OUTPUT 2Y 7 2Y 3B 10 3B INPUT _ C 4 Q 15 STROBE 1A INPUT C S 1A 2 GND 8 3Y G INPUT INPUT 9 3Y OUTPUT HT-ST7 IC6004 R1191H050B-T1-FE 5 VDD 4 ECO THERMAL PROTECTION VOLTAGE REFERENCE + VOUT 1 REVERSE DETECTOR PEAK CURRENT PROTECTION SHORT PROTECTION GND 2 CE 3 – AMP Board – IC3001, 3003, 3005, 3007 CXD9981TN GVDD_B 1 /OTW 2 NC NC 3 4 /SD 5 PWM_A 6 /RESET_AB INTERNAL PULLUP RESISTORS TO VREG 8 OC_ADJ 9 44 GVDD_A 4 43 BST_A 42 NC PROTECTION AND I/O LOGIC POWER ON RESET VREG 41 PVDD_A 40 PVDD_A TEMP. SENSE OVERLOAD PROTECTION 7 PWM_B 4 UNDER VOLTAGE PROTECTION 39 OUT_A ISENSE BTL/P BTL-CONFIGURATION PULLDOWN RESISTORS 38 GND_A 37 GND_B BTL/P BTL-CONFIGURATION PULLDOWN RESISTORS 36 OUT_B GND 10 PWM RCV. AGND 11 CTRT. TIMING 35 PVDD_B GATE DRIVE 34 BST_B 33 BST_C VREG 12 32 PVDD_C M3 13 M2 PWM RCV. 14 31 OUT_C CTRT. TIMING GATE DRIVE BTL/P BTL-CONFIGURATION PULLDOWN RESISTORS 30 GND_C M1 15 29 GND_D PWM_C 16 PWM RCV. /RESET_CD 17 PWM_D 18 NC NC 19 20 VDD 21 TIMING GATE DRIVE 28 OUT_D 27 PVDD_D 26 PVDD_D VREG VREG GVDD_C 22 CTRT. BTL/P BTL-CONFIGURATION PULLDOWN RESISTORS PWM RCV. CTRT. TIMING GATE DRIVE 25 NC 24 BST_D 23 GVDD_D 55 HT-ST7 IC3008 SI-3010KM-TLA VC 1 VIN 2 GND 3 TSD – + REF VOUT 4 ADJ 5 IC3004 TAS5538DGGR PWM_HPM_L PWM_HPP_L PWM_HPM_R PWM_HPP_R AVSS PLL_FLTM PLL_FLTP VR_ANA AVDD ASEL_EMO2 MCLK OSC_RES DVSS2_CORE DVDD2_CORE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 EMO1 RESET HP_SEL PDN MUTE 15 16 17 18 19 SDA 20 SCL 21 LRCLK SCLK SDIN1 SDIN2 SDIN3 SDIN4 VR_DIG 56 22 23 24 25 26 27 28 POWER SUPPLY DEVICE CONTROL I2C SERIAL CONTROL INTERFACE CLOCK, PLL, AND SERIAL DATA INTERFACE DIGITAL AUDIO PROCESSOR PWM SECTION 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 PWM_P_6 PWM_M_6 PWM_P_5 PWM_M_5 VR_RWM AVSS_PWM AVDD_PWM PWM_P_8 PWM_M_8 PWM_P_7 PWM_M_7 PWM_P_4 PWM_M_4 PWM_P_3 PWM_M_3 PWM_P_2 PWM_M_2 PWM_P_1 PWM_M_1 VALID DVSS1_CORE DVDD1_CORE BKND_ERR PSVC TEST LRCLKO SCLKO SDOUT HT-ST7 – DISPLAY Board – IC802 MM1836A33NRE 5 VIN CONT 1 BIAS CURRENT LIMIT – + VOLTAGE REFERENCE REGULATOR THERMAL SHUTDOWN 4 VOUT GND 2 NC 3 – POWER Board – IC501 STR-Y6735 (US and Canadian models) IC501 STR-Y6766 (AEP, UK and Australian models) STARTUP D/ST 1 DRIVER S/OCP 2 OVERCURRENT PROTECTION/ BOTTOM-SKIP VCC 3 UNDER VOLTAGE LOCK OUT/ REGULATOR/ CONSTANT CURRENT GND 4 LATCH LOGIC FB/OLP 5 FEEDBACK/ STANDBY OVERLOAD PROTECTION BD 6 BOTTOM DETECTION NF 7 OSCILLAOTR 57 HT-ST7 • IC Pin Function Description MAIN BOARD IC1002 R5F3650NCDFB (SYSTEM CONTROLLER) Pin No. 1 2 3 4 5 6 7 8 9 Pin Name SIRCS_IN TP_LED DSP MOSI DSP MISO DSP_SPICLK BYTE CNVss ROM_SDA ROM_SCLK I/O I O O I O I I I/O O 10 RESET I 11 12 13 14 15 16 17 18 Xout Vss Xin Vcc1 CEC (I/O) DIR_ZERO RFDET_NFC DRIVE_SD (DIAG) O I I/O I I I 19 WL_DET I 20 21 22 N.A. WL_RST N.A. O O O 23 HDMI_TX_5VPWR O 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 HDMI_NON_LPCM DIR ERROR DRIVE_RST DAMP_SCL0 DAMP_SDA0 M_TX_OUT_DSP M_RX_IN_DSP SCD/CLK1 BUSY/RTS1 MC_BT-TXD0 MC_BT-RXD0 N.A. MC_BT_RTS N.A. A_SEL0 HOLD WL_SCL WL_SDA BT_RST O I O O I/O O I I I O I O O O O I O I/O O 43 PCONT_BT O 44 45 46 47 48 49 50 51 52 53 WR_Flash HDMI_SDA HDMI_SCL HDMI_MUTE_DET DSP_SPIDS DSP_RESET SF_HOLD_DSP DIR_HCE DIR_XSTATE DIR_RST I I/O O O O O O O I O 58 Description SIRCS signal input from the remote control receiver LED drive signal output terminal for the Bluetooth indicator “H”: LED on Serial data output to the DSP and serial flash Serial data input from the DSP and serial flash Serial data transfer clock signal output to the DSP and serial flash External data bus width selection signal input terminal Fixed at “L” in this unit Processor mode selection signal input terminal Two-way data bus with the EEPROM Serial data transfer clock signal output to the EEPROM System reset signal input terminal “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it change to “H” System clock output terminal (8 MHz) Ground terminal System clock input terminal (8 MHz) Power supply terminal (+3.3V) Two-way CEC serial data with the HDMI connector Zero data detection signal input from the digital audio interface receiver Magnetic field detection signal input from the NFC Shut down signal input from the digital power amplifier “L”: shut down RF modulator connection detection signal input terminal “L”: RF modulator is connected Not used Reset signal output to the RF modulator “L”: reset Not used +5V power on/off control signal output terminal for the HDMI TV OUT (ARC) connector “H”: power on Audio setting signal output terminal “L”: LPCM audio, “H”: HBR audio Error detection signal input from the digital audio interface receiver “L”: error Reset signal output to the digital power amplifier “L”: reset Serial data transfer clock signal output to the stream processor Two-way data bus with the stream processor Serial data output to the DSP Serial data input from the DSP Serial data transfer clock signal input terminal for flash writing Clear to send signal input from the Bluetooth module Serial data output to the Bluetooth module Serial data input from the Bluetooth module Not used Return to send signal output to the Bluetooth module Not used Reset signal output to the sample rate converter “L”: reset Fixed at “L” in this unit I2C clock signal output to the RF modulator Two-way I2C data bus with the RF modulator Reset signal output to the Bluetooth module “L”: reset +3.3V power supply on/off control signal output terminal for the Bluetooth module “H”: power on Fixed at “H” in this unit Two-way I2C data bus with the HDMI transceiver I2C clock signal output to the HDMI transceiver HDMI muting on/off control signal input from the HDMI transceiver “H”: muting on Chip select signal output to the DSP and serial flash Reset signal output to the DSP “L”: reset Hold signal output to the serial flash Chip enable signal output to the digital audio interface receiver Source clock selection monitor input from the digital audio interface receiver Reset signal output to the digital audio interface receiver “L”: reset HT-ST7 Pin No. 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87, 88 89 90 91 92, 93 94 95 96 97 98 99 100 Pin Name HDMI_RST HDMI_MUTE_ON HDMI_INT SEL_HDMI FL_RESET P_CONT3 Vcc2 PCON_IR Vss P_CONT2 P_CONT1 WS_INT DSP_INTR DAMP_SOFT_MUTE DAMP_INIT DAMP_PDN N.A. AC_CUT KEY_INT BT_MUTE DC_DET FL_DATA FL_CS FL_CLK PCONT_HDMI N.A. PCONT_DSP SW_NFC LED_PW IRQ_NFC SEL_NFC DATA_NFC SPICLK_NFC N.A. LED_MUTE DESTINATION MODEL KEY2, KEY1 AVss KEY0 Vref AVcc DIR_DO (MC_DIR_DI) DIR_DI (MC_DIR_DO) DIR_CLK I/O O O I I O O O O O I I O O O O I I I I O O O O O O O O I O O O O O I I I I I - Description Reset signal output to the HDMI transceiver “L”: reset HDMI muting on/off control signal output terminal “H”: muting on Interrupt signal input from the HDMI transceiver HDMI selection signal output terminal “H”: HDMI Reset signal output to the fluorescent indicator tube “L”: reset Power on/off control signal output terminal for the fluorescent indicator tube “H”: power on Power supply terminal (+3.3V) +3.3V power on/off control signal output terminal for the IR section “H”: power on Ground terminal Power on/off control signal output terminal for the digital power amplifier “H”: power on Power on/off control signal output terminal “H”: power on Interrupt signal input from the RF modulator Interrupt request signal input from the DSP Soft muting on/off control signal output to stream processor “L”: muting on Reset signal output to the stream processor “L”: reset Power down signal output to the stream processor “L”: power down Not used AC cut detection signal input terminal “L”: AC cut is detected Key wake-up signal input terminal Muting on/off control signal input from the Bluetooth module “L”: muting on Speaker DC detection signal input terminal “L”: speaker DC is detected Serial data output to the fluorescent indicator tube Chip select signal output to the fluorescent indicator tube Serial data transfer clock signal output to the fluorescent indicator tube Power on/off control signal output terminal for the HDMI section “H”: power on Not used Power on/off control signal output terminal for the DSP “H”: power on Standby control signal output to the NFC “L”: standby LED drive signal output terminal for the power indicator “H”: LED on Radio data reception signal input from the NFC Data transmission direction and completion notice signal output to the NFC Serial data output to the NFC Serial data transfer clock signal output to the NFC Not used LED drive signal output terminal for the MUTING indicator “H”: LED on Destination setting terminal Model setting terminal Fixed at “L” in this unit Top panel key input terminal (A/D input) Ground terminal Power key input terminal (A/D input) Reference voltage (+3.3V) input terminal Power supply terminal (+3.3V) I Serial data input from the digital audio interface receiver O Serial data output to the digital audio interface receiver O Serial data transfer clock signal output to the digital audio interface receiver 59 HT-ST7 MAIN BOARD IC3506 SII9573CTUC (HDMI TRANSCEIVER) Pin No. 1 to 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 60 Pin Name D14 to D19 DE VSYNC HSYNC R0XC– R0XC+ R0X0– R0X0+ R0X1– R0X1+ R0X2– R0X2+ AVDD12 AVDD33 R1XC– R1XC+ R1X0– R1X0+ R1X1– R1X1+ R1X2– R1X2+ R2XC– R2XC+ R2X0– R2X0+ R2X1– R2X1+ R2X2– R2X2+ AVDD12 CVCC12 AVDD33 R3XC– R3XC+ R3X0– R3X0+ R3X1– R3X1+ R3X2– R3X2+ R4XC– R4XC+ R4X0– R4X0+ R4X1– R4X1+ R4X2– R4X2+ AVDD12 AVDD33 R5XC– R5XC+ R5X0– R5X0+ R5X1– R5X1+ R5X2– I/O I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I Description Digital video signal input terminal Not used Data enable signal input terminal Not used Vertical sync signal input terminal Not used Horizontal sync signal input terminal Not used TMDS clock (negative) signal input terminal Not used TMDS clock (positive) signal input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used Power supply terminal (+1.3V) Power supply terminal (+3.3V) TMDS clock (negative) signal input terminal Not used TMDS clock (positive) signal input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used TMDS clock (negative) signal input terminal Not used TMDS clock (positive) signal input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used TMDS data (negative) input terminal Not used TMDS data (positive) input terminal Not used Power supply terminal (+1.3V) Power supply terminal (+1.3V) Power supply terminal (+3.3V) TMDS clock (negative) signal input from the HDMI IN 1 connector TMDS clock (positive) signal input from the HDMI IN 1 connector TMDS data (negative) input from the HDMI IN 1 connector TMDS data (positive) input from the HDMI IN 1 connector TMDS data (negative) input from the HDMI IN 1 connector TMDS data (positive) input from the HDMI IN 1 connector TMDS data (negative) input from the HDMI IN 1 connector TMDS data (positive) input from the HDMI IN 1 connector TMDS clock (negative) signal input from the HDMI IN 2 connector TMDS clock (positive) signal input from the HDMI IN 2 connector TMDS data (negative) input from the HDMI IN 2 connector TMDS data (positive) input from the HDMI IN 2 connector TMDS data (negative) input from the HDMI IN 2 connector TMDS data (positive) input from the HDMI IN 2 connector TMDS data (negative) input from the HDMI IN 2 connector TMDS data (positive) input from the HDMI IN 2 connector Power supply terminal (+1.3V) Power supply terminal (+3.3V) TMDS clock (negative) signal input from the HDMI IN 3 connector TMDS clock (positive) signal input from the HDMI IN 3 connector TMDS data (negative) input from the HDMI IN 3 connector TMDS data (positive) input from the HDMI IN 3 connector TMDS data (negative) input from the HDMI IN 3 connector TMDS data (positive) input from the HDMI IN 3 connector TMDS data (negative) input from the HDMI IN 3 connector HT-ST7 Pin No. 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103, 104 105 106 107 108 109 110 111 112 113 114 115 116 117 to 120 121 122 123 124 125 126 to 128 Pin Name R5X2+ CVCC12 CSCL CSDA INT RESET TPWR_CI2CA CEC_A1 CEC_A0WAKEUP DSDA6 DSCL6 LPSVCC33 DSDA0 DSCL0 CBUS_HPD0 R0PWR5V DSDA1 DSCL1 CBUS_HPD1 R1PWR5V DSDA2 DSCL2 CBUS_HPD2 R2PWR5V DSDA3 DSCL3 CBUS_HPD3 R3PWR5V DSDA4 DSCL4 CBUS_HPD4 R4PWR5V RSVDL DSDA5 DSCL5 CBUS_HPD5 R5PWR5V SBVCC5V VCC33OUT GPIO0, GPIO1 TX_HPD0 TXDSDA0 TXDSCL0 TX_HPD1 TXDSDA1 TXDSCL1 APLL12 XTALVCC33 XTALOUT XTALIN XTALGND CVCC12 GPIO2 to GPIO5 WS0_OUT SCK0 IOVCC33 SD0_0 MCLK SD0_1 to SD0_3 I/O I I I/O O I I O O I/O I I I/O I O I I/O I O I I/O I O I I/O I O I I/O I O I I I/O I O I O I/O I I/O O I I/O O O I I/O O O O O O Description TMDS data (positive) input from the HDMI IN 3 connector Power supply terminal (+1.3V) I2C clock signal input from the system controller Two-way I2C data bus with the system controller Interrupt signal output to the system controller Reset signal input from the system controller “L”: reset Not used Not used Not used Two-way I2C serial data bus terminal Not used I2C serial data transfer clock signal input terminal Not used Not used Two-way I2C serial data bus terminal Not used I2C serial data transfer clock signal input terminal Not used Hot plug detection control signal output terminal Not used Power supply voltage (+5V) input terminal Not used Two-way I2C serial data bus terminal Not used I2C serial data transfer clock signal input terminal Not used Hot plug detection control signal output terminal Not used Power supply voltage (+5V) input terminal Not used Two-way I2C serial data bus terminal Not used I2C serial data transfer clock signal input terminal Not used Hot plug detection control signal output terminal Not used Power supply voltage (+5V) input terminal Not used Two-way I2C serial data bus with the HDMI IN 1 connector I2C serial data transfer clock signal input from the HDMI IN 1 connector Hot plug detection control signal output to the HDMI IN 1 connector Power supply voltage (+5V) input from the HDMI IN 1 connector Two-way I2C serial data bus with the HDMI IN 2 connector I2C serial data transfer clock signal input from the HDMI IN 2 connector Hot plug detection control signal output to the HDMI IN 2 connector Power supply voltage (+5V) input from the HDMI IN 2 connector Not used Two-way I2C serial data bus with the HDMI IN 3 connector I2C serial data transfer clock signal input from the HDMI IN 3 connector Hot plug detection control signal output to the HDMI IN 3 connector Power supply voltage (+5V) input from the HDMI IN 3 connector Power supply terminal (+5V) Power supply (+3.3V) output terminal Not used Hot plug detection signal input terminal Not used Two-way I2C serial data bus terminal Not used I2C serial data transfer clock signal output terminal Not used Hot plug detection signal input from the HDMI OUT TV ARC connector Two-way I2C serial data bus with the HDMI OUT TV ARC connector I2C serial data transfer clock signal output to the HDMI OUT TV ARC connector Power supply terminal (+1.3V) Power supply terminal (+3.3V) System clock signal output terminal (27 MHz) System clock signal input terminal (27 MHz) Ground terminal Power supply terminal (+1.3V) Not used L/R sampling clock signal output to the digital audio interface receiver Bit clock signal output to the digital audio interface receiver Power supply terminal (+3.3V) Digital audio signal output to the digital audio interface receiver Master clock signal output to the digital audio interface receiver Digital audio signal output to the digital audio interface receiver 61 HT-ST7 Pin No. 129 130 131, 132 133 134 135 136 137 138 139 140, 141 142 143 144 145 146 147 148 149 150, 151 152 153 154 155 156 157 158 159 160 161 to 171 172 173 174 to 176 62 Pin Name MUTEOUT SPDIF0_OUT GPIO11, GPIO10 SPDIFO_IN SCK1_OUT WS1_OUT SPDIF1_OUT ARC0 ARC1 CVCC12 TPVDD12 T1XC– T1XC+ T1X0– T1X0+ T1X1– T1X1+ T1X2– T1X2+ TPVDD12 T0XC– T0XC+ T0X0– T0X0+ T0X1– T0X1+ T0X2– T0X2+ CVCC12 D0 to D10 IDCK IOVCC33 D11 to D13 I/O O O I/O I O O O I I O O O O O O O O O O O O O O O O I I I Description HDMI muting on/off control signal output terminal “H”: muting on S/PDIF audio signal output to the digital audio interface receiver Not used S/PDIF audio signal input terminal Not used Serial data transfer clock signal output terminal Not used Word select signal output terminal Not used S/PDIF audio signal output to the digital audio interface receiver Digital audio signal input from the HDMI OUT TV ARC connector Digital audio signal input terminal Not used Power supply terminal (+1.3V) Power supply terminal (+1.3V) TMDS clock (negative) output to the HDMI OUT TV ARC connector TMDS clock (positive) output to the HDMI OUT TV ARC connector TMDS data (negative) output to the HDMI OUT TV ARC connector TMDS data (positive) output to the HDMI OUT TV ARC connector TMDS data (negative) output to the HDMI OUT TV ARC connector TMDS data (positive) output to the HDMI OUT TV ARC connector TMDS data (negative) output to the HDMI OUT TV ARC connector TMDS data (positive) output to the HDMI OUT TV ARC connector Power supply terminal (+1.3V) TMDS clock (negative) output terminal Not used TMDS clock (positive) output terminal Not used TMDS data (negative) output terminal Not used TMDS data (positive) output terminal Not used TMDS data (negative) output terminal Not used TMDS data (positive) output terminal Not used TMDS data (negative) output terminal Not used TMDS data (positive) output terminal Not used Power supply terminal (+1.2V) Digital video signal input terminal Not used Output data clock signal input terminal Not used Power supply terminal (+3.3V) Digital video signal input terminal Not used HT-ST7 MAIN BOARD IC5001 ADSST-AVR-3046 (DSP) Pin No. 1 2 3 4 Pin Name SDDQM MS0 SDCKE VDDINT I/O O O O - 5 CLK_CFG1 I 6 7 8 9 to 13 14 15 16, 17 18, 19 20, 21 ADDR0 BOOT_CFG0 VDDEXT ADDR1 to ADDR5 BOOT_CFG1 GND ADDR6, ADDR7 NC ADDR8, ADDR97 O I O I O O 22 CLK_CFG0 I 23 24 25 26 27 28 29 30 31 32 33 34 35 VDDINT CLKIN XTAL ADDR10 SDA10 VDDEXT VDDINT ADDR11 ADDR12 ADDR17 ADDR13 VDDINT ADDR18 RESETOUT/ RUNRSTIN VDDINT MOSI MISO SPICLK VDDINT DPI_P05 DSP_CS MD VDDEXT NC RESET_MAIN VDDINT UART_OUT UART_IN LED NC VDDEXT NC VDDINT NC VDDINT NC VDDINT NC WDTRSY0 NC VDDEXT I O O O O O O O O Description Data mask signal output to the SD-RAM Memory selection signal output to the SD-RAM Clock enable signal output to the SD-RAM Power supply terminal (+1.1V) (for core) Core instruction rate to CLKIN (pin 24) ratio selection signal input terminal Fixed at “L” in this unit Address signal output to the SD-RAM Boot mode selection signal input terminal Fixed at “H” in this unit Power supply terminal (+3.3V) (for I/O) Address signal output to the SD-RAM Serial data input from the system controller Ground terminal Address signal output to the SD-RAM Not used Address signal output to the SD-RAM Core instruction rate to CLKIN (pin 24) ratio selection signal input terminal Fixed at “L” in this unit Power supply terminal (+1.1V) (for core) System clock input terminal (25 MHz) System clock output terminal (25 MHz) Address signal output terminal Not used Address signal output to the SD-RAM Power supply terminal (+3.3V) (for I/O) Power supply terminal (+1.1V) (for core) Address signal output to the SD-RAM Address signal output terminal Not used Bank address signal output to the SD-RAM Address signal output terminal Not used Power supply terminal (+1.1V) (for core) Bank address signal output to the SD-RAM I/O Reset signal output and running reset signal input terminal I O I I I O I O - Power supply terminal (+1.1V) (for core) Serial data input from the system controller Serial data output to the system controller Serial data transfer clock signal input from the system controller Power supply terminal (+1.1V) (for core) Chip select signal input from the system controller Chip select signal input from the system controller Not used Power supply terminal (+3.3V) (for I/O) Not used Not used Power supply terminal (+1.1V) (for core) Serial data output to the system controller Serial data input from the system controller Not used Not used Power supply terminal (+3.3V) (for I/O) Not used Power supply terminal (+1.1V) (for core) Not used Power supply terminal (+1.1V) (for core) Not used Power supply terminal (+1.1V) (for core) Not used Watchdog timer reset signal output terminal Not used Not used Power supply terminal (+3.3V) (for I/O) 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 to 56 57 58 to 61 62 63, 64 65 66, 67 68 69 70 71 72 Not used 63 HT-ST7 Pin No. 73 74 75 I/O O I I Description Audio signal (for surround L-ch/R-ch) output to the stream processor Audio signal (for surround L-ch/R-ch) input from the digital audio interface receiver Bit clock signal input from the digital audio interface receiver O Audio signal output terminal 77 78 79 to 83 84 85 86 87 88 89 90 91 92 93 Pin Name SL/SR_OUT SL/SR_IN BCLK_IN OPTION_L/ OPTION_R_OUT FRONTHI_L/R_OUT VDDINT NC VDDEXT VDDINT L/R_OUT MID/SW2_OUT SBL/SBR_OUT ZONE_L/R VDDINT VDDEXT MCLK_IN VDDINT O O O O I/O I - 94 C/SW_OUT O 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113, 114 115 116 117 118 119 120 to 122 123 124, 125 126 127, 128 129 130 131 132 133 134 135 136 137 138 C/SW_IN A/D_2CH LRCLK_IN BCLK_OUT LRCLK_OUT L/R_IN SBL/SBR_IN VDDINT DIR_IN VDDEXT VDDINT BOOT_CFG2 VDDINT AMI_ACK GND THD_M THD_P VDDEXT VDDINT MS1 VDDINT WDT_CLKO WDT_CLKIN VDDEXT I I I O O I I I I I O I O O I - Audio signal output terminal Not used Power supply terminal (+1.1V) (for core) Not used Power supply terminal (+3.3V) (for I/O) Power supply terminal (+1.1V) (for core) Audio signal (for front L-ch/R-ch) output to the stream processor Audio signal output terminal Not used Audio signal (for surround back L-ch/R-ch) output to the stream processor Not used Power supply terminal (+1.1V) (for core) Power supply terminal (+3.3V) (for I/O) Master clock signal input from the digital audio interface receiver Power supply terminal (+1.1V) (for core) Audio signal (for center) output to the stream processor and audio signal (for subwoofer output to the RF modulator Audio signal (for center and subwoofer) input from the digital audio interface receiver Audio signal input from the digital audio interface receiver L/R sampling clock signal input from the digital audio interface receiver Bit clock signal output to the stream processor and RF modulator L/R sampling clock signal output to the stream processor and RF modulator Audio signal (for front L-ch/R-ch) input from the digital audio interface receiver Audio signal (for surround back L-ch/R-ch) input from the digital audio interface receiver Power supply terminal (+1.1V) (for core) Audio signal input from the digital audio interface receiver Power supply terminal (+3.3V) (for I/O) Power supply terminal (+1.1V) (for core) Boot mode selection signal input terminal Fixed at “L” in this unit Power supply terminal (+1.1V) (for core) Acknowledge signal input terminal Not used Ground terminal Thermal detection signal output terminal Not used Thermal detection signal input terminal Not used Power supply terminal (+3.3V) (for I/O) Power supply terminal (+1.1V) (for core) Memory selection signal output terminal Not used Power supply terminal (+1.1V) (for core) Watchdog time clock signal output terminal Not used Watchdog time clock signal input terminal Not used Power supply terminal (+3.3V) (for I/O) ADDR23 to ADDR21 O Address signal output terminal VDDINT ADDR20, ADDR19 VDDEXT ADDR16, ADDR15 VDDINT ADDR14 AMI_WR AMI_RD VDDINT IRQ FLAG1 FLAG2 MLBCLK FLAG3 O O O O O O I I I - Power supply terminal (+1.1V) (for core) Address signal output terminal Not used Power supply terminal (+3.3V) (for I/O) Address signal output terminal Not used Power supply terminal (+1.1V) (for core) Address signal output terminal Not used Write enable signal output terminal Not used Read enable signal output terminal Not used Power supply terminal (+1.1V) (for core) Interrupt request signal output to the system controller Error detection signal input terminal “L”: error Audio setting signal input terminal “L”: LPCM audio, “H”: HBR audio Media local bus clock signal input terminal Not used Not used 76 64 Not used Not used HT-ST7 Pin No. 139 140 141 142 143 144 145 146 147 to 150 151 152 153 154, 155 156 157 158 159 160 161 to 163 164 165 to 168 169 170 171 172 173 174 175 176 Pin Name MLBDAT MLBDO VDDEXT MLBSIG VDDINT TRST MLBSO EMU I/O I/O O I/O I O O Description Two-way media local bus data terminal Not used Media local bus data output terminal Not used Power supply terminal (+3.3V) (for I/O) Two-way media local bus signal terminal Not used Power supply terminal (+1.1V) (for core) Test reset signal input terminal (for JTAG) Not used Media local bus signal output terminal Not used Emulation status signal output terminal Not used DATA0 to DATA3 I/O Two-way data bus with the SD-RAM TDO DATA4 VDDEXT DATA5, DATA6 VDDINT DATA7 TDI SDCLK VDDEXT O I/O I/O I/O I O - Test data output terminal (for JTAG) Not used Two-way data bus with the SD-RAM Power supply terminal (+3.3V) (for I/O) Two-way data bus with the SD-RAM Power supply terminal (+1.1V) (for core) Two-way data bus with the SD-RAM Test data input terminal (for JTAG) Not used Clock signal output to the SD-RAM Power supply terminal (+3.3V) (for I/O) DATA8 to DATA10 I/O Two-way data bus with the SD-RAM TCK DATA11, DATA12, DATA14, DATA13 VDDINT DATA15 SWE SDRAS RESET TMS SDCAS VDDINT I Test clock signal input terminal (for JTAG) Not used I/O Two-way data bus with the SD-RAM I/O O O I I O - Power supply terminal (+1.1V) (for core) Two-way data bus with the SD-RAM Write enable signal output to the SD-RAM Row address signal output to the SD-RAM Reset signal input from the system controller “L”: reset Test mode selection signal input terminal (for JTAG) Not used Column address signal output to the SD-RAM Power supply terminal (+1.1V) (for core) 65 HT-ST7 SECTION 5 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. 5-1. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • The mechanical parts with no reference number in the exploded views are not supplied. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet’s Color • Abbreviation AUS : Australian model CND : Canadian model Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. The components identified by mark 9 contain confidential information. Strictly follow the instructions whenever the components are repaired and/or replaced. Les composants identifiés par la marque 9 contiennent des informations confidentielles. Suivre scrupuleusement les instructions chaque fois qu’un composant est remplacé et / ou réparé. PANEL SECTION • Rear bottom view #1 #1 5 3 3 3 3 2 3 3 3 3 not supplied not supplied 3 3 3 3 6 3 3 3 7 3 #1 #1 3 4 3 bracket (bottom) section 1 6 7 Ref. No. 1 1 2 3 4 66 Part No. Description X-2587-428-1 X-2587-726-1 4-448-411-01 4-468-968-01 X-2587-738-1 PANEL (REAR L) ASSY (US, CND) PANEL (REAR L) ASSY (AEP, UK, AUS) PANEL (REAR R) SCREW (STEP) +BVTP3 PANEL (L) ASSY (for L-ch) Remark Ref. No. 5 6 7 #1 Part No. Description X-2587-737-1 4-457-796-01 4-449-062-01 7-685-647-79 PANEL (R) ASSY (for R-ch) FOOT (CORNER) CUSHION (FOOT) SCREW +BVTP 3X10 TYPE2 IT-3 Remark HT-ST7 5-2. BRACKET (BOTTOM) SECTION • Rear bottom view 51 #2 #2 #2 not supplied #2 #2 #2 #2 51 #2 not supplied #2 #2 #2 #2 #2 #2 #2 not supplied #2 not supplied #2 not supplied not supplied #2 #2 #2 #2 #2 #2 not supplied 52 not supplied 52 52 52 52 52 52 52 52 Ref. No. 51 52 Part No. Description 4-472-036-01 3-704-515-22 CUSHION (GROUND) SCREW (BV/RING) Remark Ref. No. #2 power cord section Part No. Description 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3 Remark 67 HT-ST7 5-3. POWER CORD SECTION • Rear bottom view AC1 #2 D CPA1 C #2 A (UK) #2 B 104 #2 #2 not supplied 102 #2 BT1 B D 101 C chassis section NFC1 103 101 103 FFC5 (8 pin) 101 front block section A Note: As for WIRE KIT (B-FFC), all flat flexible cables (Ref. No. FFC1, FFC2, FFC3, FFC4, FFC5, FFC6, FFC7) will be 1 set. Ref. No. Part No. Description * 101 102 103 0 104 0 AC1 3-378-109-01 3-087-053-01 4-449-063-01 4-966-267-12 1-777-071-83 CUSHION, SARANET +BVTP2.6 (3CR) CUSHION (NFC) BUSHING (FBS001), CORD CORD, POWER (AEP, UK) 0 AC1 1-835-068-21 CORD, POWER (AUS) 68 Remark Ref. No. Part No. Description Remark 0 AC1 BT1 0 CPA1 FFC5 1-837-308-11 1-490-558-61 1-770-019-72 9-833-605-97 CORD, POWER-SUPPLY (US, CND) BLUETOOTH MODULE ADAPTOR, CONVERSION PLUG 3P (UK) WIRE KIT (B-FFC) (8 pin) (See Note) NFC1 #2 8-989-470-00 7-685-646-79 RC-S801/A (NFC) SCREW +BVTP 3X8 TYPE2 IT-3 HT-ST7 5-4. CHASSIS SECTION not supplied (IO REINFORCE board) • Rear bottom view FFC2 (9 pin) 153 I #3 #3 152 #3 E FFC4 (13 pin) not supplied FFC3 (28 pin) 154 159 159 159 159 159 #3 G #3 #4 159 G 159 J #3 #3 not supplied 157 #3 F #3 157 157 J I #3 #2 #2 #2 #2 #4 #4 #4 157 158 159 156 #3 F E not supplied not supplied 151 H #3 #3 #3 #3 #3 #2 #2 #2 #3 not supplied #2 156 #3 160 #2 #3 #3 not supplied #2 F502 155 #2 H 161 #2 #4 #4 #2 #4 #4 #2 – Right view – not supplied Note 1: As for WIRE KIT (B-FFC), all flat flexible cables (Ref. No. FFC1, FFC2, FFC3, FFC4, FFC5, FFC6, FFC7) will be 1 set. Note 2: When the complete MAIN board is replaced, refer to “ABOUT THE PAIRING METHOD” on page 4. Part No. Description 9 151 Ref. No. A-1968-239-A 9 151 A-1968-240-A 152 153 154 A-1917-931-A 4-461-378-11 4-454-144-01 MAIN BOARD, COMPLETE (for SERVICE) (US, CND, AUS) (See Note 2) MAIN BOARD, COMPLETE (for SERVICE) (AEP, UK) (See Note 2) IO BOARD, COMPLETE TAPE (BT) HOUSING (WIRELESS) Remark 155 155 156 157 158 A-1917-935-A A-1917-937-A 4-237-065-01 3-905-609-13 A-1917-930-A POWER BOARD, COMPLETE (US, CND) POWER BOARD, COMPLETE (AEP, UK, AUS) CLAMP (L35) SCREW (TRANSISTOR) AMP BOARD, COMPLETE (See Note 3) not supplied Note 3: When the complete AMP board is replaced, refer to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on page 4. Ref. No. Part No. Description 159 160 * 161 0 F502 FFC2 4-974-510-11 4-231-099-91 3-378-109-01 1-576-232-51 9-833-605-97 SCREW (+BV 3X8 CU) SHEET, RADIATION CUSHION, SARANET FUSE (H.B.C.) (T 5 AH/250 V) WIRE KIT (B-FFC) (9 pin) (See Note 1) FFC3 FFC4 #2 #3 #4 9-833-605-97 9-833-605-97 7-685-646-79 7-685-646-71 7-682-547-09 WIRE KIT (B-FFC) (28 pin) (See Note 1) WIRE KIT (B-FFC) (13 pin) (See Note 1) SCREW +BVTP 3X8 TYPE2 IT-3 SCREW +BVTP 3X8 TYPE2 IT-3 SCREW +B 3X6 Remark 69 HT-ST7 5-5. FRONT BLOCK SECTION • Rear bottom view 201 201 201 202 #5 201 204 #5 203 #5 203 #5 center speaker section DISPLAY board section #5 front speaker (L) section #5 205 205 205 205 205 205 205 205 205 front panel section Ref. No. 201 202 203 * 204 70 Part No. Description 2-249-250-00 4-454-143-01 4-472-037-01 3-378-109-01 CLIP (SMALL), CANOE SHEET (JACK) CUSHION (SLIT) CUSHION, SARANET Remark Ref. No. Part No. Description 205 4-469-674-01 SCREW +BVP-TITE 3X8 BZN #5 7-685-903-21 TAPPING +PWH 3X8 TYPE2 N-S Remark HT-ST7 5-6. FRONT SPEAKER (L) SECTION • Front bottom view 251 251 251 SP3 251 251 251 251 251 251 251 251 not supplied SP1 not supplied not supplied 251 251 252 254 254 252 252 not supplied (MOUNTED board) 253 252 253 not supplied not supplied not supplied 251 not supplied SPC1 Ref. No. 251 252 253 * 254 SP1 Part No. Description 4-986-971-21 4-469-674-01 4-472-037-01 3-378-109-01 1-858-867-12 SCREW (3.5) SCREW +BVP-TITE 3X8 BZN CUSHION (SLIT) CUSHION, SARANET LOUDSPEAKER (2 cm) (Tweeter) (L-ch) Remark Ref. No. SP3 SPC1 Part No. Description Remark 1-858-869-21 1-846-506-11 LOUDSPEAKER (6.5 cm) (Woofer) (L-ch) CABLE WITH CONNECTOR (GRAY/BLACK) (for L-ch) 71 HT-ST7 5-7. CENTER SPEAKER SECTION • Front bottom view 301 SP5 301 301 301 SP9 301 301 301 301 301 301 SP7 301 301 SP8 301 301 301 301 not supplied 301 301 SP6 301 not supplied not supplied 301 not supplied not supplied not supplied SPC4 not supplied not supplied SPC3 Ref. No. 301 SP5 SP6 SP7 SP8 72 Part No. Description 4-986-971-21 1-858-869-11 1-858-869-11 1-858-869-11 1-858-869-11 SCREW (3.5) LOUDSPEAKER (6.5 cm) (Surround) (L-ch) LOUDSPEAKER (6.5 cm) (Surround) (R-ch) LOUDSPEAKER (6.5 cm) (Surround Back) (L-ch) LOUDSPEAKER (6.5 cm) (Surround Back) (R-ch) Remark Ref. No. Part No. Description SP9 SPC3 1-858-869-11 1-846-507-11 SPC4 1-846-508-11 LOUDSPEAKER (6.5 cm) (Center) CABLE WITH CONNECTOR (4P) (for Surround L/R) CABLE WITH CONNECTOR (6P) (for Center, Surround Back L/R) Remark HT-ST7 5-8. DISPLAY BOARD SECTION • Front bottom view #6 354 353 352 #6 351 353 355 #6 352 353 #6 FFC6 (15 pin) 353 352 352 front speaker (R) section Note: As for WIRE KIT (B-FFC), all flat flexible cables (Ref. No. FFC1, FFC2, FFC3, FFC4, FFC5, FFC6, FFC7) will be 1 set. Ref. No. 351 352 353 354 Part No. Description A-1917-932-A 4-453-877-01 4-453-878-01 X-2587-419-1 DISPLAY BOARD, COMPLETE BUSHING (DAMPER) COLLAR (DAMPER) HOLDER (LED) ASSY Remark Ref. No. * 355 FFC6 #6 Part No. Description 3-378-109-01 CUSHION, SARANET 9-833-605-97 7-685-648-79 WIRE KIT (B-FFC) (15 pin) (See Note) SCREW +BVTP 3X12 TYPE2 IT-3 Remark 73 HT-ST7 5-9. FRONT SPEAKER (R) SECTION • Front bottom view 401 401 401 SP4 401 401 401 401 401 not supplied 401 401 not supplied (MOUNTED board) K L 401 402 402 not supplied SP2 402 401 402 401 SPC2 not supplied L K not supplied not supplied not supplied 401 not supplied Ref. No. 401 402 SP2 74 Part No. Description 4-986-971-21 4-469-674-01 1-858-867-12 SCREW (3.5) SCREW +BVP-TITE 3X8 BZN LOUDSPEAKER (2 cm) (Tweeter) (R-ch) Remark Ref. No. SP4 SPC2 Part No. Description 1-858-869-21 1-846-506-21 LOUDSPEAKER (6.5 cm) (Woofer) (R-ch) CABLE WITH CONNECTOR (RED/BLACK) (for R-ch) Remark HT-ST7 5-10. FRONT PANEL SECTION • Rear bottom view FFC1 (14 pin) 457 453 FFC7 (5 pin) 451 451 not supplied (KEY board) 455 454 454 454 455 455 452 455 454 454 456 451 451 451 451 451 451 Note: As for WIRE KIT (B-FFC), all flat flexible cables (Ref. No. FFC1, FFC2, FFC3, FFC4, FFC5, FFC6, FFC7) will be 1 set. Ref. No. 451 452 453 454 455 Part No. Description 4-448-417-01 4-465-794-01 4-461-341-01 X-2587-407-1 3-087-053-01 CATCHER (FLEX-G) CUSHION (BT PAD) SHEET (BT) BUTTON ASSY +BVTP2.6 (3CR) Remark Ref. No. 456 457 FFC1 FFC7 Part No. Description A-1968-811-A 4-461-378-01 9-833-605-97 9-833-605-97 FRONT PANEL ASSY (SERVICE) TAPE (BT) WIRE KIT (B-FFC) (14 pin) (See Note) WIRE KIT (B-FFC) (5 pin) (See Note) Remark 75 HT-ST7 SECTION 6 ELECTRICAL PARTS LIST AMP Note: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable Ref. No. • CAPACITORS uF: μF • COILS uH: μH • SEMICONDUCTORS In each case, u: μ, for example: uA. . : μA. . , uPA. . , μPA. . , uPB. . : μPB. . , uPC. . , μPC. . , uPD. . : μPD. . • Abbreviation AUS : Australian model CND : Canadian model Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. When indicating parts by reference number, please include the board name. Part No. Description Remark A-1917-930-A AMP BOARD, COMPLETE (See Note) ******************** < CAPACITOR > C3002 C3007 C3012 C3013 C3014 1-114-325-11 1-116-731-11 1-114-325-11 1-118-361-11 1-114-325-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 2.2uF 0.1uF 0.1uF 0.1uF 10% 20% 10% 10% 10% 25V 6.3V 25V 50V 25V C3015 C3020 C3023 C3026 C3027 1-118-361-11 1-114-507-11 1-114-325-11 1-116-716-11 1-114-507-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 1uF 0.1uF 10uF 1uF 10% 10% 10% 10% 10% 50V 50V 25V 16V 50V C3028 C3034 C3038 C3039 C3040 1-100-905-11 1-100-905-11 1-112-781-11 1-100-905-11 1-118-290-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 1uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 10V 50V 50V C3043 C3044 C3045 C3046 C3047 1-118-290-11 1-114-507-11 1-114-885-51 1-112-252-21 1-118-290-11 CERAMIC CHIP CERAMIC CHIP FILM ELECT CERAMIC CHIP 0.001uF 1uF 1uF 560uF 0.001uF 10% 10% 5% 20% 10% 50V 50V 50V 35V 50V C3048 C3049 C3051 C3052 C3054 1-100-905-11 1-114-507-11 1-118-290-11 1-114-885-51 1-118-361-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM CERAMIC CHIP 0.001uF 1uF 0.001uF 1uF 0.1uF 10% 10% 10% 5% 10% 50V 50V 50V 50V 50V C3055 C3056 C3057 C3058 C3059 1-114-325-11 1-118-361-11 1-116-731-11 1-116-731-11 1-112-251-21 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 0.1uF 0.1uF 2.2uF 2.2uF 470uF 10% 10% 20% 20% 20% 25V 50V 6.3V 6.3V 35V C3060 C3061 C3062 C3063 C3064 1-114-325-11 1-118-361-11 1-114-325-11 1-118-361-11 1-118-290-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.001uF 10% 10% 10% 10% 10% 25V 50V 25V 50V 50V C3067 C3068 C3069 1-114-507-11 1-114-885-51 1-118-361-11 CERAMIC CHIP 1uF FILM 1uF CERAMIC CHIP 0.1uF 10% 5% 10% 50V 50V 50V Note: When the complete AMP board is replaced, refer to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on page 4. 76 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. The components identified by mark 9 contain confidential information. Strictly follow the instructions whenever the components are repaired and/or replaced. Les composants identifiés par la marque 9 contiennent des informations confidentielles. Suivre scrupuleusement les instructions chaque fois qu’un composant est remplacé et / ou réparé. Part No. Description Remark C3070 C3071 1-112-776-11 1-118-361-11 CERAMIC CHIP 0.0047uF CERAMIC CHIP 0.1uF 10% 10% 50V 50V C3072 C3073 C3074 C3075 C3076 1-114-325-11 1-118-290-11 1-112-779-11 1-116-717-11 1-112-252-21 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 0.1uF 0.001uF 0.047uF 10uF 560uF 10% 10% 10% 20% 20% 25V 50V 25V 10V 35V C3077 C3078 C3079 C3080 C3081 1-116-716-11 1-114-507-11 1-112-779-11 1-118-361-11 1-100-905-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 1uF 0.047uF 0.1uF 0.001uF 10% 10% 10% 10% 10% 16V 50V 25V 50V 50V C3083 C3084 C3085 C3087 C3088 1-118-290-11 1-112-776-11 1-118-361-11 1-118-290-11 1-114-885-51 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM 0.001uF 0.0047uF 0.1uF 0.001uF 1uF 10% 10% 10% 10% 5% 50V 50V 50V 50V 50V C3089 C3091 C3093 C3095 C3096 1-100-905-11 1-112-781-11 1-118-290-11 1-118-290-11 1-114-507-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 1uF 0.001uF 0.001uF 1uF 10% 10% 10% 10% 10% 50V 10V 50V 50V 50V C3097 C3098 C3099 C3100 C3101 1-114-885-51 1-112-252-21 1-118-361-11 1-116-717-11 1-118-361-11 FILM ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 560uF 0.1uF 10uF 0.1uF 5% 20% 10% 20% 10% 50V 35V 50V 10V 50V C3102 C3103 C3104 C3106 C3107 1-116-717-11 1-118-290-11 1-114-507-11 1-118-290-11 1-114-885-51 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM 10uF 0.001uF 1uF 0.001uF 1uF 20% 10% 10% 10% 5% 10V 50V 50V 50V 50V C3109 C3110 C3111 C3113 C3114 1-118-361-11 1-114-325-11 1-118-361-11 1-116-717-11 1-118-361-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 10uF 0.1uF 10% 10% 10% 20% 10% 50V 25V 50V 10V 50V C3115 C3116 C3117 C3118 C3119 1-116-731-11 1-118-361-11 1-116-717-11 1-116-731-11 1-114-325-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 2.2uF 0.1uF 10uF 2.2uF 0.1uF 20% 10% 20% 20% 10% 6.3V 50V 10V 6.3V 25V HT-ST7 AMP Ref. No. Part No. Description Part No. Description C3120 C3121 C3122 C3125 C3128 1-118-361-11 1-114-325-11 1-118-361-11 1-118-290-11 1-114-507-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.001uF 1uF 10% 10% 10% 10% 10% 50V 25V 50V 50V 50V Remark Ref. No. C3206 C3208 C3209 C3211 C3212 1-114-507-11 1-118-290-11 1-114-885-51 1-118-361-11 1-114-325-11 CERAMIC CHIP CERAMIC CHIP FILM CERAMIC CHIP CERAMIC CHIP 1uF 0.001uF 1uF 0.1uF 0.1uF 10% 10% 5% 10% 10% 50V 50V 50V 50V 25V Remark C3129 C3130 C3131 C3132 C3133 1-114-885-51 1-114-325-11 1-118-290-11 1-112-252-21 1-116-716-11 FILM CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 1uF 0.1uF 0.001uF 560uF 10uF 5% 10% 10% 20% 10% 50V 25V 50V 35V 16V C3213 C3214 C3219 C3221 1-118-361-11 1-114-507-11 1-118-012-11 1-118-012-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 1uF 0.47uF 0.47uF 10% 10% 5% 5% 50V 50V 25V 25V C3134 C3135 C3137 C3138 C3139 1-114-507-11 1-100-905-11 1-118-290-11 1-118-290-11 1-114-885-51 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM 1uF 0.001uF 0.001uF 0.001uF 1uF 10% 10% 10% 10% 5% 50V 50V 50V 50V 50V C3140 C3142 C3143 C3145 C3147 1-100-905-11 1-112-781-11 1-100-905-11 1-118-290-11 1-118-290-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 1uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 10V 50V 50V 50V C3148 C3149 C3150 C3151 C3152 1-114-507-11 1-114-885-51 1-112-252-21 1-100-905-11 1-118-290-11 CERAMIC CHIP FILM ELECT CERAMIC CHIP CERAMIC CHIP 1uF 1uF 560uF 0.001uF 0.001uF 10% 5% 20% 10% 10% 50V 50V 35V 50V 50V C3154 C3156 C3157 C3163 C3164 1-114-507-11 1-118-290-11 1-114-885-51 1-126-952-11 1-118-361-11 CERAMIC CHIP CERAMIC CHIP FILM ELECT CERAMIC CHIP 1uF 0.001uF 1uF 1000uF 0.1uF 10% 10% 5% 20% 10% 50V 50V 50V 35V 50V C3165 C3166 C3168 C3169 C3171 1-114-325-11 1-118-361-11 1-116-731-11 1-114-325-11 1-118-361-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 2.2uF 0.1uF 0.1uF 10% 10% 20% 10% 10% 25V 50V 6.3V 25V 50V C3172 C3174 C3175 C3178 C3180 1-114-325-11 1-116-731-11 1-118-361-11 1-118-290-11 1-114-507-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 2.2uF 0.1uF 0.001uF 1uF 10% 20% 10% 10% 10% 25V 6.3V 50V 50V 50V C3181 C3183 C3184 C3185 C3186 1-114-885-51 1-114-325-11 1-118-290-11 1-112-831-31 1-116-716-11 FILM CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 1uF 0.1uF 0.001uF 2200uF 10uF 5% 10% 10% 20% 10% 50V 25V 50V 35V 16V C3187 C3188 C3190 C3191 C3192 1-114-507-11 1-100-905-11 1-118-290-11 1-118-290-11 1-114-885-51 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM 1uF 0.001uF 0.001uF 0.001uF 1uF 10% 10% 10% 10% 5% 50V 50V 50V 50V 50V C3193 C3195 C3196 C3197 C3200 1-100-905-11 1-112-781-11 1-100-905-11 1-118-290-11 1-118-290-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 1uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 10V 50V 50V 50V C3201 C3202 C3203 C3204 C3205 1-114-507-11 1-114-885-51 1-112-831-31 1-100-905-11 1-118-290-11 CERAMIC CHIP FILM ELECT CERAMIC CHIP CERAMIC CHIP 1uF 1uF 2200uF 0.001uF 0.001uF 10% 5% 20% 10% 10% 50V 50V 35V 50V 50V < CONNECTOR > CN3001 * CN3002 * CN3003 CN3004 CN3006 1-820-841-31 1-564-507-11 1-564-509-11 1-564-242-00 1-564-505-11 CONNECTOR, FFC/FPC (LIF) 28P PLUG, CONNECTOR 4P PLUG, CONNECTOR 6P PIN, CONNECTOR (3.96 mm PITCH) 5P PLUG, CONNECTOR 2P * CN3007 1-564-506-11 PLUG, CONNECTOR 3P < DIODE > D3001 D3002 6-502-961-01 6-502-974-01 DIODE DA2J10100L DIODE DZ2J140M0L < LUG TERMINAL > * * * * ET3001 ET3003 ET3004 ET3005 1-780-408-11 1-780-408-11 1-780-408-11 1-780-408-11 TERMINAL, LUG TERMINAL, LUG TERMINAL, LUG TERMINAL, LUG < FUSE > F3002 F3003 F3004 F3005 F3006 1-523-144-31 1-523-144-31 1-523-144-31 1-523-144-31 1-523-144-31 FUSE (5 A/32 V) FUSE (5 A/32 V) FUSE (5 A/32 V) FUSE (5 A/32 V) FUSE (5 A/32 V) 0 F3007 0 F3008 1-523-144-31 1-523-144-31 FUSE (5 A/32 V) FUSE (5 A/32 V) 0 0 0 0 0 < FERRITE BEAD > FB3001 FB3002 1-400-180-21 1-400-180-21 INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) < IC > IC3001 IC3003 IC3004 IC3005 IC3007 6-714-477-01 6-714-477-01 6-718-103-01 6-714-477-01 6-714-477-01 IC IC IC IC IC CXD9981TN (See Note) CXD9981TN (See Note) TAS5538DGGR CXD9981TN (See Note) CXD9981TN (See Note) IC3008 6-717-953-01 IC SI-3010KM-TLA < COIL > L3006 L3007 L3011 L3013 L3014 1-457-579-11 1-457-579-11 1-469-524-91 1-457-579-11 1-457-579-11 CHOKE COIL CHOKE COIL INDUCTOR CHOKE COIL CHOKE COIL 10uH 10uH 4.7uH 10uH 10uH L3019 L3022 L3027 1-457-579-11 1-457-579-11 1-457-579-11 CHOKE COIL CHOKE COIL CHOKE COIL 10uH 10uH 10uH Note: When the IC3001, IC3003, IC3005 and IC3007 on the AMP board are replaced, refer to “NOTE OF REPLACING THE IC3001, IC3003, IC3005 AND IC3007 ON THE AMP BOARD AND THE COMPLETE AMP BOARD” on page 4. 77 HT-ST7 AMP Ref. No. Part No. Description Remark < TRANSISTOR > Ref. No. Part No. Description R3071 1-216-304-11 METAL CHIP 3.3 5% 1/10W Remark Q3001 Q3003 Q3004 Q3005 Q3006 6-552-892-01 8-729-013-22 8-729-013-22 8-729-013-22 8-729-013-22 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR LSCR523UBFS8TL HN1A01FU HN1A01FU HN1A01FU HN1A01FU R3072 R3073 R3074 R3075 R3077 1-216-304-11 1-218-965-11 1-216-864-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP SHORT CHIP 3.3 10K 0 0 0 5% 5% 1/10W 1/16W Q3007 Q3008 Q3009 8-729-013-22 8-729-013-22 8-729-013-22 TRANSISTOR TRANSISTOR TRANSISTOR HN1A01FU HN1A01FU HN1A01FU R3078 R3079 R3080 R3081 R3083 1-216-797-11 1-216-864-11 1-218-965-11 1-216-864-11 1-218-977-11 METAL CHIP SHORT CHIP METAL CHIP SHORT CHIP METAL CHIP 10 0 10K 0 100K 5% 1/10W 5% 1/16W 5% 1/16W < RESISTOR > R3001 R3002 R3004 R3007 R3009 1-216-864-11 1-218-977-11 1-218-965-11 1-218-967-11 1-218-977-11 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 100K 10K 15K 100K 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W R3084 R3086 R3087 R3089 R3090 1-218-977-11 1-216-837-11 1-216-304-11 1-216-304-11 1-250-455-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 22K 3.3 3.3 22 5% 5% 5% 5% 1% 1/16W 1/10W 1/10W 1/10W 1/16W R3014 R3017 R3018 R3019 R3020 1-216-805-11 1-216-805-11 1-216-805-11 1-216-805-11 1-216-837-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47 47 47 47 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3091 R3092 R3093 R3094 R3095 1-250-455-11 1-216-304-11 1-216-304-11 1-216-296-11 1-216-296-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP 22 3.3 3.3 0 0 1% 5% 5% 1/16W 1/10W 1/10W R3021 R3022 R3026 R3028 R3029 1-216-805-11 1-216-805-11 1-216-805-11 1-250-455-11 1-216-805-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47 47 47 22 47 5% 5% 5% 1% 5% 1/10W 1/10W 1/10W 1/16W 1/10W R3096 R3097 R3098 R3099 R3100 1-250-455-11 1-250-455-11 1-216-296-11 1-216-304-11 1-216-304-11 METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP 22 22 0 3.3 3.3 1% 1% 1/16W 1/16W 5% 5% 1/10W 1/10W R3030 R3036 R3038 R3039 R3040 1-250-455-11 1-250-455-11 1-250-455-11 1-216-296-11 1-216-304-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 22 22 22 0 3.3 1% 1% 1% 1/16W 1/16W 1/16W SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 0 3.3 3.3 0 100K 1/10W 1/10W 1/10W 1-216-296-11 1-216-304-11 1-216-304-11 1-216-864-11 1-216-845-11 5% 5% 5% R3101 R3102 R3103 R3104 R3105 5% 1/10W R3041 R3042 R3043 R3044 R3045 1-216-304-11 1-216-296-11 1-216-304-11 1-216-304-11 1-216-864-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP 3.3 0 3.3 3.3 0 5% 1/10W 5% 5% 1/10W 1/10W R3109 R3112 R3113 R3114 R3115 1-218-977-11 1-218-977-11 1-216-837-11 1-216-304-11 1-216-304-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 22K 3.3 3.3 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/10W 1/10W R3047 R3048 R3049 R3050 R3051 1-218-977-11 1-218-990-81 1-218-990-81 1-218-990-81 1-218-990-81 METAL CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 100K 0 0 0 0 5% 1/16W R3116 R3117 R3118 R3119 R3120 1-250-455-11 1-250-455-11 1-216-304-11 1-216-304-11 1-216-296-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 22 22 3.3 3.3 0 1% 1% 5% 5% 1/16W 1/16W 1/10W 1/10W R3052 R3053 R3054 R3055 R3056 1-218-977-11 1-216-837-11 1-216-304-11 1-216-304-11 1-250-455-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 22K 3.3 3.3 22 5% 5% 5% 5% 1% 1/16W 1/10W 1/10W 1/10W 1/16W R3121 R3122 R3123 R3124 R3125 1-216-296-11 1-250-455-11 1-250-455-11 1-216-296-11 1-216-304-11 SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 0 22 22 0 3.3 1% 1% 1/16W 1/16W 5% 1/10W R3057 R3058 R3059 R3060 R3061 1-218-949-11 1-250-455-11 1-218-949-11 1-216-304-11 1-216-304-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 22 470 3.3 3.3 5% 1% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/10W R3126 R3127 R3128 R3129 R3130 1-216-304-11 1-216-296-11 1-216-304-11 1-216-304-11 1-216-864-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP 3.3 0 3.3 3.3 0 5% 1/10W 5% 5% 1/10W 1/10W R3062 R3063 R3064 R3065 R3066 1-216-296-11 1-216-296-11 1-216-835-11 1-216-864-11 1-250-646-11 SHORT CHIP SHORT CHIP METAL CHIP SHORT CHIP METAL CHIP 0 0 15K 0 18K 5% 1/10W 1% 1/10W R3134 R3135 R3136 R3137 R3138 1-218-965-11 1-218-977-11 1-216-833-11 1-218-977-11 1-218-977-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100K 10K 100K 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/16W 1/16W R3067 R3068 R3069 R3070 1-216-296-11 1-216-304-11 1-216-304-11 1-216-296-11 SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP 0 3.3 3.3 0 5% 5% 1/10W 1/10W R3141 R3143 1-216-308-00 1-216-308-00 METAL CHIP METAL CHIP 4.7 4.7 5% 5% 1/10W 1/10W 78 HT-ST7 AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description IO Remark < RESISTOR > < COMPOSITION CIRCUIT BLOCK > RB3001 1-234-372-11 RES, NETWORK 100 (1005X4) RB3002 1-234-372-11 RES, NETWORK 100 (1005X4) RB3004 1-234-381-11 RES, NETWORK 100K (1005X4) RB3005 1-234-381-11 RES, NETWORK 100K (1005X4) RB3006 1-234-381-11 RES, NETWORK 100K (1005X4) ************************************************************* A-1917-932-A DISPLAY DISPLAY BOARD, COMPLETE *********************** < CAPACITOR > R801 R802 R803 R804 R805 1-216-827-11 1-216-805-11 1-216-805-11 1-216-839-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 3.3K 47 47 33K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R806 R807 R808 R809 R810 1-216-809-11 1-216-809-11 1-216-797-11 1-216-797-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 10 10 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C802 C803 C805 C806 C807 1-165-492-21 1-118-371-11 1-116-717-11 1-112-776-11 1-116-734-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100uF 0.015uF 10uF 0.0047uF 1uF 20% 10% 20% 10% 20% 10V 50V 10V 50V 16V R812 R813 R814 R815 R816 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/16W C808 C809 C810 C811 C812 1-128-991-21 1-114-325-11 1-118-361-11 1-114-325-11 1-100-906-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 0.1uF 0.1uF 0.01uF 20% 10% 10% 10% 10% 50V 25V 50V 25V 16V R817 R818 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP 100 100 5% 5% 1/16W 1/16W C813 C814 C815 C816 C817 1-112-068-11 1-112-068-11 1-112-068-11 1-116-734-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220PF 220PF 220PF 1uF 0.1uF 10% 10% 10% 20% 10% 50V 50V 50V 16V 16V C818 C819 C824 1-100-916-11 1-100-916-11 1-112-068-11 CERAMIC CHIP 0.1uF CERAMIC CHIP 0.1uF CERAMIC CHIP 220PF 10% 10% 10% 16V 16V 50V < TRANSFORMER > T801 1-697-282-11 TRANSFORMER, DC-DC CONVERTER ************************************************************* A-1917-931-A IO BOARD, COMPLETE ****************** < CAPACITOR > < CONNECTOR > CN801 1-842-042-51 C201 C202 C203 C204 C205 1-116-717-11 1-112-068-11 1-112-068-11 1-114-325-11 1-114-325-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 220PF 220PF 0.1uF 0.1uF 20% 10% 10% 10% 10% 10V 50V 50V 25V 25V C206 C207 C215 C219 C223 1-116-717-11 1-116-717-11 1-164-842-11 1-116-734-11 1-114-325-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 10uF 2PF 1uF 0.1uF 20% 20% 0.25PF 20% 10% 10V 10V 50V 16V 25V C230 C263 C4001 C4002 1-165-492-21 1-164-315-91 1-100-905-11 1-100-905-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100uF 470PF 0.001uF 0.001uF 20% 5% 10% 10% 10V 50V 50V 50V CONNECTOR, FFC/FPC 15P < DIODE > D801 D802 D803 D804 D805 6-500-400-01 6-500-400-01 6-502-966-01 6-502-395-01 6-503-196-01 DIODE BAV99-215 DIODE BAV99-215 DIODE DZ2J056M0L LED SL-194S-WS-SD-T (POWER INDICATOR) LED CL-194S-HB8SP-SD-T (Bluetooth INDICATOR) D806 6-502-195-01 LED SML-D12D8WT86SQ (MUTING) < CONNECTOR > < IC > IC801 IC802 6-600-767-01 6-716-993-01 CN201 CN4001 CN4002 IC PNA4823M02S0 ( ) IC MM1836A33NRE 1-820-112-51 1-785-468-51 1-838-505-11 CONNECTOR, FFC/FPC 9P CONNECTOR, FFC/FPC 13P CONNECTOR, CARD EDGE 30P (L) (EZW-RT50/EZW-RT20) < COIL > < IC > L801 1-460-379-11 COIL, CHOKE (SMD) 100uH < FLUORESCENT INDICATOR TUBE > ND802 1-483-482-11 IC201 IC202 IC205 6-600-827-01 6-600-827-01 8-759-591-61 IC JSR1124 (DIGITAL IN OPT 2) IC JSR1124 (DIGITAL IN OPT 1 (TV)) IC TC7WHU04FU (TE12R) VACUUM FLUORESCENT DISPLAY < JACK > < TRANSISTOR > Q801 Q802 Q803 Q804 Q805 6-553-098-01 6-553-098-01 6-552-941-01 6-552-941-01 6-552-941-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTC3552T-RTK/PW KTC3552T-RTK/PW LTC023JUBFS8TL LTC023JUBFS8TL LTC023JUBFS8TL J201 J202 J251 1-821-058-11 1-784-431-11 1-563-330-31 JACK, PIN 2P (ANALOG IN) JACK, PIN 1P (DIGITAL IN COAX) JACK (IR BLASTER) < COIL > L202 1-400-922-11 INDUCTOR 220uH 79 HT-ST7 IO KEY Ref. No. MAIN Part No. Description Remark Ref. No. Part No. Q251 6-552-892-01 TRANSISTOR LSCR523UBFS8TL < RESISTOR > R201 R202 R203 R204 R205 1-216-809-11 1-216-864-11 1-216-825-11 1-216-825-11 1-216-833-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 100 0 2.2K 2.2K 10K 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R206 R208 R209 R224 R225 1-216-833-11 1-216-839-11 1-216-839-11 1-218-949-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 33K 33K 470 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/16W 1/10W R228 R233 R235 R237 R251 1-216-849-11 1-216-809-11 1-216-809-11 1-216-809-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220K 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/16W R252 R253 R254 R4001 R4002 1-218-965-11 1-216-803-11 1-216-803-11 1-218-953-11 1-218-990-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 10K 33 33 1K 0 5% 5% 5% 5% 1/16W 1/10W 1/10W 1/16W R4003 1-218-990-81 SHORT CHIP 0 R4004 1-218-945-11 METAL CHIP 220 5% 1/16W R4005 1-218-945-11 METAL CHIP 220 5% 1/16W R4006 1-218-965-11 METAL CHIP 10K 5% 1/16W R4007 1-218-990-81 SHORT CHIP 0 ************************************************************* KEY BOARD ********** < CAPACITOR > C751 C752 C755 1-100-916-11 1-100-916-11 1-100-916-11 CERAMIC CHIP 0.1uF CERAMIC CHIP 0.1uF CERAMIC CHIP 0.1uF 10% 10% 10% 16V 16V 16V < CONNECTOR > CN751 1-816-184-51 CONNECTOR, FFC/FPC 5P < RESISTOR > R751 R754 1-216-825-11 1-216-825-11 METAL CHIP METAL CHIP Description Remark < CAPACITOR > < TRANSISTOR > 2.2K 2.2K 5% 5% 1/10W 1/10W C601 C602 C603 C605 C607 1-128-992-21 1-116-865-11 1-116-865-11 1-116-865-11 1-112-777-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 10uF 10uF 10uF 0.01uF 20% 10% 10% 10% 10% 25V 25V 25V 25V 25V C608 C609 C610 C613 C614 1-112-777-11 1-100-916-11 1-100-916-11 1-128-992-21 1-112-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.01uF 0.1uF 0.1uF 47uF 0.01uF 10% 10% 10% 20% 10% 25V 16V 16V 25V 25V C615 C616 C617 C619 C620 1-112-777-11 1-107-819-11 1-100-916-11 1-100-916-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.022uF 0.1uF 0.1uF 10uF 10% 10% 10% 10% 20% 25V 16V 16V 16V 6.3V C621 * C622 C623 C624 * C625 1-116-720-11 1-116-714-11 1-116-720-11 1-116-720-11 1-116-714-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 22uF 10uF 10uF 22uF 20% 20% 20% 20% 20% 6.3V 6.3V 6.3V 6.3V 6.3V C626 C628 C629 C636 C637 1-116-737-11 1-116-737-11 1-116-737-11 1-116-865-11 1-112-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 1uF 1uF 10uF 0.01uF 20% 20% 20% 10% 10% 10V 10V 10V 25V 25V C638 C640 C643 C644 C645 1-100-916-11 1-112-777-11 1-116-716-11 1-116-716-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.01uF 10uF 10uF 10uF 10% 10% 10% 10% 20% 16V 25V 16V 16V 6.3V C646 C647 C648 * C649 C650 1-116-720-11 1-116-713-11 1-116-716-11 1-116-714-11 1-116-711-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 22uF 10uF 22uF 22uF 20% 20% 10% 20% 20% 6.3V 10V 16V 6.3V 16V C651 C901 C902 C903 C904 1-116-717-11 1-100-916-11 1-116-734-11 1-112-777-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 1uF 0.01uF 10uF 20% 10% 20% 10% 20% 10V 16V 16V 25V 6.3V C905 C906 C907 C908 C911 1-116-720-11 1-164-866-11 1-164-866-11 1-100-916-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 47PF 47PF 0.1uF 0.1uF 20% 5% 5% 10% 10% 6.3V 50V 50V 16V 16V C912 C913 C914 C916 C917 1-164-852-11 1-116-734-11 1-116-734-11 1-114-340-81 1-114-325-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 12PF 1uF 1uF 15PF 0.1uF 5% 20% 20% 2% 10% 50V 16V 16V 50V 25V C918 C919 C920 C921 C922 1-112-776-11 1-110-563-11 1-100-916-11 1-116-720-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0047uF 0.068uF 0.1uF 10uF 10uF 10% 10% 10% 20% 20% 50V 16V 16V 6.3V 6.3V C923 C924 C932 C933 1-164-874-11 1-164-874-11 1-116-734-11 1-165-492-21 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 100PF 100PF 1uF 100uF 5% 5% 20% 20% 50V 50V 16V 10V < SWITCH > S751 1-786-653-11 SWITCH, TACTILE (?/1) S752 1-786-653-11 SWITCH, TACTILE (INPUT) S753 1-786-653-11 SWITCH, TACTILE (VOLUME –) S754 1-786-653-11 SWITCH, TACTILE (VOLUME +) S755 1-786-653-11 SWITCH, TACTILE (BLUETOOTH, PAIRING) ************************************************************* 9 A-1968-239-A 9 A-1968-240-A MAIN BOARD, COMPLETE (for SERVICE) (US, CND, AUS) (See Note) MAIN BOARD, COMPLETE (for SERVICE) (AEP, UK) (See Note) ******************** Note: When the complete MAIN board is replaced, refer to “ABOUT THE PAIRING METHOD” on page 4. 80 HT-ST7 MAIN Ref. No. Part No. Description Part No. Description C934 1-116-734-11 CERAMIC CHIP 1uF 20% 16V Remark Ref. No. C3546 1-100-916-11 CERAMIC CHIP 0.1uF 10% 16V Remark C940 C941 C945 C946 C1001 1-116-720-11 1-100-916-11 1-116-717-11 1-116-726-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 10uF 2.2uF 0.1uF 20% 10% 20% 10% 10% 6.3V 16V 10V 25V 16V C3548 C3549 C3550 C3551 C3552 1-100-916-11 1-164-850-11 1-164-850-11 1-116-720-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10PF 10PF 10uF 0.1uF 10% 0.5PF 0.5PF 20% 10% 16V 50V 50V 6.3V 16V C1002 C1003 C1005 C1006 C1007 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C3553 C3554 C3555 C3557 C3558 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C1008 C1009 C1010 C1012 C1014 1-116-720-11 1-114-320-11 1-112-777-11 1-112-777-11 1-107-819-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.22uF 0.01uF 0.01uF 0.022uF 20% 10% 10% 10% 10% 6.3V 6.3V 25V 25V 16V C3559 C3560 C3562 C3563 C3564 1-100-916-11 1-116-720-11 1-116-720-11 1-116-720-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 10uF 10uF 10uF 10% 20% 20% 20% 20% 16V 6.3V 6.3V 6.3V 6.3V C1015 C1016 C1019 C1020 C1021 1-116-734-11 1-165-492-21 1-116-734-11 1-135-825-21 1-100-916-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP FILM CHIP CERAMIC CHIP 1uF 100uF 1uF 0.0047uF 0.1uF 20% 20% 20% 2% 10% 16V 10V 16V 16V 16V C3565 C3566 C3567 C3568 C3569 1-116-720-11 1-114-385-11 1-114-385-11 1-116-724-11 1-116-737-11 CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 10uF 470uF 470uF 4.7uF 1uF 20% 20% 20% 20% 20% 6.3V 6.3V 6.3V 6.3V 10V C1023 C1025 C1026 C1027 C1028 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 10uF 10% 10% 10% 10% 20% 16V 16V 16V 16V 6.3V C3725 C3727 C3728 C3729 C3730 1-116-737-11 1-116-737-11 1-116-737-11 1-116-724-11 1-116-726-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 1uF 1uF 4.7uF 2.2uF 20% 20% 20% 20% 10% 10V 10V 10V 6.3V 25V C1029 C1030 C1201 C1202 C1203 1-164-874-11 1-164-874-11 1-100-916-11 1-128-392-11 1-118-403-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 100PF 100PF 0.1uF 470uF 0.001uF 5% 5% 10% 20% 10% 50V 50V 16V 6.3V 50V C3731 C3732 C3733 C5000 C5001 1-116-717-11 1-116-726-11 1-116-717-11 1-100-916-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 2.2uF 10uF 0.1uF 0.1uF 20% 10% 20% 10% 10% 10V 25V 10V 16V 16V C1204 C1205 C1206 C1207 C1208 1-118-403-11 1-118-403-11 1-118-403-11 1-118-403-11 1-118-403-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C5002 C5003 C5004 C5005 C5006 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C3358 C3363 C3364 C3516 C3518 1-116-737-11 1-116-737-11 1-116-737-11 1-116-724-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 1uF 1uF 4.7uF 0.1uF 20% 20% 20% 20% 10% 10V 10V 10V 6.3V 16V C5007 C5008 C5009 C5012 C5014 1-100-916-11 1-165-989-11 1-114-385-11 1-100-916-11 1-112-777-11 CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 470uF 0.1uF 0.01uF 10% 10% 20% 10% 10% 16V 6.3V 6.3V 16V 25V C3519 C3520 C3523 C3525 C3526 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C5016 C5017 C5018 C5019 C5020 1-165-989-11 1-165-989-11 1-114-385-11 1-165-989-11 1-114-582-91 CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 10uF 10uF 470uF 10uF 0.1uF 10% 10% 20% 10% 10% 6.3V 6.3V 6.3V 6.3V 16V C3527 C3528 C3529 C3532 C3533 1-116-724-11 1-100-916-11 1-100-916-11 1-116-724-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 0.1uF 0.1uF 4.7uF 10uF 20% 10% 10% 20% 20% 6.3V 16V 16V 6.3V 6.3V C5021 C5022 C5023 C5024 C5025 1-114-582-91 1-114-582-91 1-100-916-11 1-100-916-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C3534 C3536 C3538 C3540 C3541 1-116-737-11 1-100-916-11 1-116-720-11 1-100-916-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 0.1uF 10uF 0.1uF 10uF 20% 10% 20% 10% 20% 10V 16V 6.3V 16V 6.3V C5026 C5027 C5028 C5029 C5030 1-114-582-91 1-114-582-91 1-114-582-91 1-100-916-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C3542 C3543 C3544 C3545 1-100-916-11 1-116-720-11 1-100-916-11 1-116-720-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 0.1uF 10uF 10% 20% 10% 20% 16V 6.3V 16V 6.3V C5031 C5032 C5033 C5034 1-114-582-91 1-114-582-91 1-100-916-11 1-114-582-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 16V 16V 16V 16V 81 HT-ST7 MAIN Ref. No. Part No. Description C5035 1-114-582-91 CERAMIC CHIP 0.1uF 10% 16V Remark C5036 C5037 C5038 C5039 C5040 1-100-916-11 1-114-582-91 1-114-582-91 1-100-916-11 1-114-582-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C5041 C5042 C5043 C5044 C5045 1-165-989-11 1-100-916-11 1-100-916-11 1-100-916-11 1-114-582-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 6.3V 16V 16V 16V 16V C5046 C5047 C5048 C5049 C5050 1-100-916-11 1-100-916-11 1-100-916-11 1-114-582-91 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C5051 C5052 C5053 C5054 C5055 1-114-582-91 1-165-989-11 1-114-582-91 1-114-582-91 1-114-385-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.1uF 10uF 0.1uF 0.1uF 470uF 10% 10% 10% 10% 20% 16V 6.3V 16V 16V 6.3V C5056 C5057 C5058 C5059 C5060 1-100-916-11 1-165-989-11 1-114-582-91 1-165-989-11 1-114-582-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 0.1uF 10uF 0.1uF 10% 10% 10% 10% 10% 16V 6.3V 16V 6.3V 16V C5061 C5062 C5064 C5065 C5066 1-114-582-91 1-100-916-11 1-114-582-91 1-114-582-91 1-114-582-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C5067 C5068 C5069 C5070 C5071 1-114-582-91 1-100-916-11 1-114-582-91 1-114-385-11 1-114-385-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP 0.1uF 0.1uF 0.1uF 470uF 470uF 10% 10% 10% 20% 20% 16V 16V 16V 6.3V 6.3V C5072 C5074 C5076 C5105 C5500 1-165-989-11 1-114-582-91 1-165-989-11 1-127-715-11 1-100-916-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 10uF 0.22uF 0.1uF 10% 10% 10% 10% 10% 6.3V 16V 6.3V 16V 16V C5501 C5502 C5503 C5505 C5506 1-100-916-11 1-100-916-11 1-100-916-11 1-164-858-11 1-164-850-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 22PF 10PF 10% 10% 10% 5% 0.5PF 16V 16V 16V 50V 50V Ref. No. CN3503 CN5002 Part No. Description 1-821-398-41 1-820-841-31 HDMI CONNECTOR (HDMI IN 1) CONNECTOR, FFC/FPC (LIF) 28P < DIODE > D901 D1001 D1002 D1003 D1004 6-500-400-01 6-502-934-01 6-502-934-01 6-502-961-01 6-502-934-01 DIODE DIODE DIODE DIODE DIODE BAV99-215 DB2S31100K8 DB2S31100K8 DA2J10100L DB2S31100K8 D1005 D1006 D1007 D1008 D5001 6-502-961-01 6-502-978-01 6-502-934-01 6-502-961-01 6-502-934-01 DIODE DIODE DIODE DIODE DIODE DA2J10100L DA2J10400L DB2S31100K8 DA2J10100L DB2S31100K8 < LUG TERMINAL > ET1001 ET1002 ET3500 ET3501 ET5000 1-780-408-11 1-780-408-11 1-780-408-11 1-780-408-11 1-780-408-11 TERMINAL, LUG TERMINAL, LUG TERMINAL, LUG TERMINAL, LUG TERMINAL, LUG * ET5001 1-780-408-11 TERMINAL, LUG * * * * * < FERRITE BEAD > FB601 FB602 FB603 FB901 FB902 1-400-180-21 1-400-180-21 1-400-180-21 1-400-180-21 1-400-180-21 INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) FB903 FB1001 FB1002 FB1003 FB1005 1-400-180-21 1-400-180-21 1-400-180-21 1-400-180-21 1-400-180-21 INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) FB1006 FB1007 FB1008 FB3503 FB3504 1-400-180-21 1-400-180-21 1-400-180-21 1-400-921-21 1-400-580-21 INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) INDUCTOR, EMI FERRITE (1608) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FB3505 FB3506 FB5000 FB5001 FB5002 1-481-348-21 1-481-348-21 1-481-467-11 1-481-467-11 1-400-180-21 EMI FERRITE (SMD) (1608) EMI FERRITE (SMD) (1608) BEAD, FERRITE (CHIP) BEAD, FERRITE (CHIP) INDUCTOR, EMI FERRITE (1608) FB5003 1-400-180-21 INDUCTOR, EMI FERRITE (1608) < FILTER > < CONNECTOR > CN601 CN901 CN902 CN1001 CN1002 1-779-993-11 1-820-112-51 1-815-762-31 1-785-468-51 1-820-384-31 PIN, CONNECTOR (PWB) 5P CONNECTOR, FFC/FPC 9P CONNECTOR, FFC/FPC (LIF) 14P CONNECTOR, FFC/FPC 13P CONNECTOR, FFC/FPC (LIF) 8P CN1004 CN1005 CN1006 CN1007 CN3200 1-691-550-11 1-820-115-51 1-784-861-51 1-794-362-51 1-821-398-41 PIN, CONNECTOR (1.5 mm) (SMD) 3P CONNECTOR, FFC/FPC 15P CONNECTOR, FFC (LIF (NON-ZIF)) 9P CONNECTOR, FFC/FPC 5P HDMI CONNECTOR (HDMI OUT ARC TV) CN3501 CN3502 1-821-398-41 1-821-398-41 HDMI CONNECTOR (HDMI IN 3) HDMI CONNECTOR (HDMI IN 2) 82 FL5000 FL5002 FL5003 1-400-874-11 1-400-874-11 1-400-874-11 FILTER, EMI REMOVAL (SMD) FILTER, EMI REMOVAL (SMD) FILTER, EMI REMOVAL (SMD) < IC > IC601 IC602 IC603 IC604 IC605 6-717-879-01 6-717-879-01 6-716-781-01 6-717-680-01 6-717-879-01 IC IC IC IC IC RT8293ALZSP RT8293ALZSP RT8252ALGSP BD00IC0WEFJ-E2 RT8293ALZSP IC901 IC902 IC904 6-707-800-01 6-719-198-01 6-716-745-01 IC SRC4182 IC MM3411A33URE IC PCM9211PTR Remark HT-ST7 MAIN Ref. No. Part No. Description IC905 IC906 6-710-366-01 6-719-198-01 IC 74LVC1G04GW-125 IC MM3411A33URE Remark IC908 IC1001 IC1002 IC1004 IC1005 6-717-798-01 6-714-351-01 A-1968-244-A 6-713-333-01 6-719-198-01 IC IC IC IC IC R1191N050B-TR-FE R1EX24016ASAS0A R5F3650NCDFB (for SERVICE) (See Note 1) PST8429UL MM3411A33URE IC1006 IC1007 IC3506 IC3704 IC5000 6-709-888-01 6-706-483-01 (Not supplied) 6-717-680-01 6-716-354-01 IC IC IC IC IC TC7WHU04FK TC7SH02FU SII9573CTUC (See Note 2) BD00IC0WEFJ-E2 W9864G6JH-6-ER10 IC5001 IC5002 IC5101 IC5102 IC5105 6-719-106-01 A-1968-245-A 6-710-388-01 6-704-099-01 6-707-870-01 IC IC IC IC IC ADSST-AVR-3046 W25Q16CVSSIG-R (for SERVICE) 74LVC1G79GW-125 TC7WZ08FK TC74VHC157FT (EKJ) IC5500 IC6004 IC6005 8-759-655-22 6-720-524-01 6-717-798-01 IC TC7WH34FK IC R1191H050B-T1-FE IC R1191N050B-TR-FE < COIL > L601 L602 L603 L604 L605 1-400-789-21 1-400-789-21 1-400-789-21 1-457-995-11 1-457-995-11 INDUCTOR INDUCTOR INDUCTOR CHOKE COIL CHOKE COIL 2.2uH 2.2uH 2.2uH 10uH 10uH L606 L607 L608 L611 L612 1-457-995-11 1-400-789-21 1-457-995-11 1-457-995-11 1-457-995-11 CHOKE COIL INDUCTOR CHOKE COIL CHOKE COIL CHOKE COIL 10uH 2.2uH 10uH 10uH 10uH L902 L903 L905 L906 L907 1-481-524-11 1-481-524-11 1-412-977-41 1-481-524-11 1-400-922-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 10uH 10uH 0.68uH 10uH 220uH L1001 L1002 L3500 L5504 1-400-789-21 1-400-789-21 1-469-555-21 1-412-977-41 INDUCTOR INDUCTOR INDUCTOR INDUCTOR 2.2uH 2.2uH 10uH 0.68uH < TRANSISTOR > Q1001 Q1002 Q1004 * Q5001 Q5002 6-551-346-01 6-552-892-01 6-552-936-01 6-552-923-01 6-552-936-01 FET TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR LSK3541FS8T2L LSCR523UBFS8TL LTC014EUBFS8TL LTA014TUBFS8TL LTC014EUBFS8TL < RESISTOR > R601 R602 R603 R604 R605 1-218-953-11 1-218-953-11 1-218-961-11 1-218-961-11 1-218-990-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 1K 1K 4.7K 4.7K 0 R606 R607 R608 R609 * R610 1-218-990-81 1-218-977-11 1-218-969-11 1-250-519-11 1-250-523-11 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 100K 22K 10K 15K 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 5% 5% 1% 1% 1/16W 1/16W 1/16W 1/16W Note 1: When IC1002 on the MAIN board is replaced, refer to “ABOUT THE PAIRING METHOD” on page 4. Ref. No. Part No. Description R611 * R612 R613 R614 * R615 1-250-495-11 1-250-507-11 1-250-487-11 1-250-519-11 1-250-507-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 3.3K 470 10K 3.3K 1% 1% 1% 1% 1% 1/16W 1/16W 1/16W 1/16W 1/16W Remark R616 * R617 R621 * R622 R623 1-250-519-11 1-250-507-11 1-218-953-11 1-250-523-11 1-250-535-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 3.3K 1K 15K 47K 1% 1% 5% 1% 1% 1/16W 1/16W 1/16W 1/16W 1/16W R627 R628 R629 R631 R632 1-218-953-11 1-218-961-11 1-218-990-81 1-250-531-11 1-250-519-11 METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP 1K 4.7K 0 33K 10K 5% 5% 1/16W 1/16W 1% 1% 1/16W 1/16W * R633 R901 R902 R903 R904 1-250-511-11 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 100 100 100 100 1% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R905 R906 R907 R908 R909 1-218-941-81 1-218-941-81 1-218-945-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP 100 100 220 0 0 5% 5% 5% 1/16W 1/16W 1/16W R910 R911 R912 R913 R914 1-218-941-81 1-218-941-81 1-218-957-11 1-218-957-11 1-218-957-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 2.2K 2.2K 2.2K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R915 R916 R918 R919 R920 1-218-941-81 1-218-977-11 1-218-977-11 1-218-990-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 100 100K 100K 0 100 5% 5% 5% 1/16W 1/16W 1/16W 5% 1/16W R921 R922 R923 R924 R925 1-218-941-81 1-218-990-81 1-218-941-81 1-218-941-81 1-218-965-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 100 0 100 100 10K 5% 1/16W 5% 5% 5% 1/16W 1/16W 1/16W R926 R927 R928 R929 R930 1-218-941-81 1-218-941-81 1-218-953-11 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 1K 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R931 R933 R934 R938 R943 1-218-941-81 1-218-941-81 1-218-941-81 1-218-947-11 1-218-951-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 330 680 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R949 R950 R951 R954 R955 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R956 R957 R958 R959 R960 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W Note 2: IC3506 on the MAIN board cannot exchange with single. When this part is damaged, exchange the complete mounted board. 83 HT-ST7 MAIN Ref. No. Part No. Description R961 R963 R964 R965 R967 1-218-941-81 1-218-941-81 1-218-941-81 1-218-953-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 1K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W Part No. Description R1059 R1060 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP 100 100 5% 5% 1/16W 1/16W R1061 R1062 R1063 R1064 R1065 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R968 R973 R974 R976 R1001 1-218-941-81 1-218-953-11 1-218-953-11 1-218-965-11 1-218-965-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 1K 1K 10K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1068 R1069 R1070 R1071 R1072 1-218-941-81 1-218-941-81 1-218-973-11 1-218-977-11 1-218-973-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 47K 100K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1002 R1003 R1004 1-218-965-11 1-218-965-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP 10K 10K 4.7K 5% 5% 5% R1004 1-216-837-11 METAL CHIP 22K R1006 1-218-961-11 METAL CHIP 4.7K 1/16W 1/16W 1/10W (AEP, UK) 5% 1/10W (US, CND, AUS) 5% 1/16W R1073 R1074 R1075 R1076 R1077 1-218-965-11 1-218-990-81 1-218-971-11 1-218-971-11 1-218-977-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 10K 0 33K 33K 100K 5% 1/16W 5% 5% 5% 1/16W 1/16W 1/16W R1007 R1008 R1010 R1011 R1012 1-218-961-11 1-218-977-11 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 100K 100 100 100 5% 5% 5% 5% 5% R1078 R1081 R1082 R1083 R1085 1-218-941-81 1-250-648-11 1-250-664-11 1-250-628-11 1-250-626-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 22K 100K 3.3K 2.7K 5% 1% 1% 1% 1% 1/16W 1/10W 1/10W 1/10W 1/10W R1013 1-216-841-11 METAL CHIP 47K 5% 10K 10K 1K 10K 1/10W (US, CND, AUS) 5% 1/10W 5% 1/16W 5% 1/16W 5% 1/16W R1014 R1015 R1016 R1017 1-216-833-11 1-218-965-11 1-218-953-11 1-218-965-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP R1087 R1088 R1089 R1090 R1091 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-218-953-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1018 R1020 R1021 R1022 R1023 1-218-977-11 1-218-941-81 1-218-941-81 1-218-973-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100 100 47K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1092 R1093 R1094 R1095 R1096 1-218-953-11 1-218-953-11 1-218-977-11 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 100K 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1025 R1026 R1027 R1028 R1029 1-218-941-81 1-218-977-11 1-218-941-81 1-218-977-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100K 100 100K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1097 R1098 R1099 R1101 R1102 1-218-941-81 1-218-941-81 1-218-953-11 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 1K 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1030 R1031 R1032 R1033 R1034 1-218-965-11 1-218-965-11 1-218-977-11 1-216-864-11 1-216-857-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 10K 10K 100K 0 1M 5% 5% 5% 1/16W 1/16W 1/16W 5% 1/10W R1103 R1104 R1105 R1106 R1107 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-218-961-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 4.7K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1037 R1038 R1039 R1040 R1041 1-218-973-11 1-216-838-11 1-218-953-11 1-218-941-81 1-218-977-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 27K 1K 100 100K 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/16W 1/16W R1115 R1116 R1117 R1118 R1231 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 100 100 100 100 0 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W R1042 R1045 R1046 R1047 R1048 1-218-965-11 1-218-937-11 1-218-937-11 1-218-937-11 1-218-937-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 47 47 47 47 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1232 R1233 R1234 R1235 R1236 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1049 R1050 R1051 R1052 R1053 1-218-941-81 1-218-965-11 1-218-961-11 1-218-973-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 10K 4.7K 47K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1237 R1238 R1239 R1240 R3365 1-218-957-11 1-218-957-11 1-218-961-11 1-218-961-11 1-218-965-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 2.2K 4.7K 4.7K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1054 R1055 R1058 1-218-941-81 1-218-977-11 1-218-965-11 METAL CHIP METAL CHIP METAL CHIP 100 100K 10K 5% 5% 5% 1/16W 1/16W 1/16W R3370 R3372 R3373 1-250-482-11 1-220-168-81 1-218-990-81 METAL CHIP METAL CHIP SHORT CHIP 300 62 0 1% 5% 1/16W 1/16W 84 Remark 1/16W 1/16W 1/16W 1/16W 1/16W Ref. No. Remark HT-ST7 MAIN Ref. No. Part No. Description Part No. Description R3374 R3376 1-220-168-81 1-218-973-11 METAL CHIP METAL CHIP 62 47K 5% 5% 1/16W 1/16W Remark R3645 R3646 1-216-864-11 1-216-864-11 SHORT CHIP SHORT CHIP 0 0 R3377 R3380 R3386 R3387 R3501 1-218-973-11 1-218-953-11 1-218-956-11 1-218-956-11 1-218-990-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 47K 1K 1.8K 1.8K 0 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W R3722 * R3723 R3724 R3725 R3726 1-218-953-11 1-250-523-11 1-250-535-11 1-218-929-11 1-218-961-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 15K 47K 10 4.7K 5% 1% 1% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R3502 R3503 R3504 R3505 R3506 1-218-990-81 1-218-990-81 1-218-957-11 1-218-957-11 1-218-990-81 SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP 0 0 2.2K 2.2K 0 R3727 R3728 R3729 R3730 R3731 1-218-990-81 1-218-990-81 1-218-933-11 1-218-933-11 1-218-973-11 SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 0 0 22 22 47K 5% 5% 5% 1/16W 1/16W 1/16W R3507 R3508 R3509 R3510 R3516 1-218-990-81 1-218-990-81 1-218-990-81 1-218-957-11 1-218-933-11 SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP 0 0 0 2.2K 22 5% 5% 1/16W 1/16W R3732 R3733 R3734 R3737 R3739 1-218-977-11 1-218-977-11 1-218-965-11 1-218-953-11 1-218-953-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 10K 1K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R3517 R3518 R3519 R3523 R3524 1-218-933-11 1-218-933-11 1-218-933-11 1-218-973-11 1-218-973-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22 22 22 47K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R3741 R5000 R5001 R5003 R5004 1-218-965-11 1-216-809-11 1-218-965-11 1-216-809-11 1-216-801-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100 10K 100 22 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/10W 1/10W * R3573 R3576 R3578 R3579 R3583 1-250-507-11 1-218-957-11 1-218-957-11 1-218-990-81 1-218-961-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 3.3K 2.2K 2.2K 0 4.7K 1% 5% 5% 1/16W 1/16W 1/16W METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 22 0 100 100 22 1/10W 1/16W 1-216-801-11 1-218-990-81 1-216-809-11 1-216-809-11 1-216-801-11 5% 5% R5005 R5007 R5008 R5009 R5011 5% 5% 5% 1/10W 1/10W 1/10W R3584 R3585 R3588 R3589 R3590 1-218-990-81 1-218-990-81 1-218-937-11 1-218-937-11 1-218-937-11 SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 0 0 47 47 47 5% 5% 5% 1/16W 1/16W 1/16W R5012 R5013 R5014 R5015 R5016 1-216-801-11 1-216-801-11 1-216-801-11 1-216-801-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22 22 22 22 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3591 R3593 R3597 R3598 R3599 1-218-965-11 1-218-953-11 1-218-961-11 1-218-929-11 1-218-961-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 1K 4.7K 10 4.7K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R5017 R5018 R5019 R5020 R5021 1-216-801-11 1-216-801-11 1-216-801-11 1-216-801-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22 22 22 22 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3600 R3601 R3602 R3606 R3616 1-218-961-11 1-218-929-11 1-218-990-81 1-216-864-11 1-218-937-11 METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP 4.7K 10 0 0 47 5% 5% 1/16W 1/16W 5% 1/16W R5022 R5023 R5024 R5025 R5026 1-216-813-11 1-216-809-11 1-216-801-11 1-216-809-11 1-216-801-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220 100 22 100 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3618 R3619 R3620 R3621 R3622 1-218-941-81 1-216-864-11 1-218-937-11 1-218-945-11 1-216-864-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP 100 0 47 220 0 5% 1/16W 5% 5% 1/16W 1/16W R5027 R5028 R5029 R5030 R5031 1-216-833-11 1-216-809-11 1-216-801-11 1-218-965-11 1-216-811-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100 22 10K 150 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/16W 1/10W R3623 R3624 R3625 R3626 R3627 1-218-937-11 1-218-989-11 1-218-949-11 1-218-937-11 1-218-937-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47 1M 470 47 47 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R5035 R5036 R5037 R5038 R5039 1-218-965-11 1-218-941-81 1-218-941-81 1-218-965-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100 100 10K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R3628 R3629 R3632 R3636 R3637 1-218-937-11 1-218-937-11 1-216-864-11 1-218-990-81 1-218-937-11 METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP 47 47 0 0 47 5% 5% 1/16W 1/16W 5% 1/16W R5040 R5041 R5042 R5043 R5044 1-218-941-81 1-218-965-11 1-216-811-11 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 10K 150 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/16W 1/16W R3640 R3643 R3644 1-216-864-11 1-216-864-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 R5045 R5046 R5047 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP 100 100 100 5% 5% 5% 1/16W 1/16W 1/16W 5% 5% 1/16W 1/16W Ref. No. Remark 85 HT-ST7 MAIN Ref. No. POWER Part No. Description R5048 R5049 1-218-965-11 1-218-941-81 METAL CHIP METAL CHIP 10K 100 5% 5% 1/16W 1/16W Remark R5051 R5052 R5053 R5054 R5055 1-218-965-11 1-216-864-11 1-216-833-11 1-218-943-11 1-218-943-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 10K 0 10K 150 150 5% 1/16W 5% 5% 5% 1/10W 1/16W 1/16W R5056 R5057 R5058 R5059 R5060 1-216-801-11 1-208-859-81 1-216-801-11 1-216-833-11 1-218-990-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 22 68 22 10K 0 5% 0.5% 5% 5% 1/10W 1/16W 1/10W 1/10W R5061 R5062 R5063 R5064 R5065 1-218-990-81 1-218-965-11 1-218-965-11 1-216-825-11 1-216-811-11 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 10K 10K 2.2K 150 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/10W R5066 R5067 R5068 R5069 R5070 1-216-811-11 1-216-811-11 1-216-801-11 1-216-801-11 1-216-801-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 150 150 22 22 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R5072 R5074 R5075 R5078 R5079 1-218-977-11 1-218-953-11 1-218-943-11 1-216-801-11 1-218-965-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 1K 150 22 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/16W R5080 R5081 R5082 R5084 R5101 1-216-801-11 1-216-825-11 1-216-801-11 1-218-965-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22 2.2K 22 10K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/16W 1/10W R5102 R5103 R5108 R5500 R5501 1-216-849-11 1-218-941-81 1-216-833-11 1-218-941-81 1-218-945-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220K 100 10K 100 220 5% 5% 5% 5% 5% 1/10W 1/16W 1/10W 1/16W 1/16W R5502 R5506 R5507 R5508 R5509 1-218-941-81 1-216-805-11 1-216-805-11 1-216-805-11 1-216-805-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 47 47 47 47 5% 5% 5% 5% 5% 1/16W 1/10W 1/10W 1/10W 1/10W R5510 R5511 R5513 R5514 R5515 1-216-805-11 1-216-805-11 1-216-821-11 1-216-857-11 1-218-977-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47 47 1K 1M 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/16W R5516 R5517 R5523 R5525 R5527 1-218-977-11 1-216-805-11 1-218-941-81 1-218-941-81 1-218-990-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 100K 47 100 100 0 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/16W R5531 1-218-990-81 SHORT CHIP 0 Ref. No. RB5005 Part No. Description 1-234-372-11 RES, NETWORK 100 (1005X4) Remark < VIBRATOR > X901 1-814-344-11 QUARTZ CRYSTAL UNIT (24.576 MHz) X1001 1-795-313-21 VIBRATOR, CERAMIC (8 MHz) X3501 1-814-345-11 QUARTZ CRYSTAL UNITS (27 MHz) X5000 1-814-242-11 VIBRATOR, CRYSTAL (25 MHz) ************************************************************* A-1917-935-A A-1917-937-A POWER BOARD, COMPLETE (US, CND) POWER BOARD, COMPLETE (AEP, UK, AUS) ********************** 3-077-331-11 +BV3 (3-CR) < CAPACITOR > 0 C501 0 C503 1-114-594-21 1-112-869-41 FILM CERAMIC 0.22uF 470PF 0 C503 1-112-870-51 CERAMIC 0.001uF 0 C504 1-112-869-41 CERAMIC 470PF 0 C504 1-112-870-51 CERAMIC 0.001uF 0 C505 0 C507 0 C508 1-114-868-11 1-162-927-91 1-114-594-21 CERAMIC CHIP 0.1uF CERAMIC CHIP 100PF FILM 0.22uF 0 C508 1-114-721-21 FILM 0.1uF 0 C509 1-116-819-51 CERAMIC 560PF 50V 50V 250V (AEP, UK, AUS) 10% 250V (US, CND) 5% 1KV 0 C511 1-112-235-21 ELECT 330uF 20% 0 C511 1-112-237-21 ELECT 560uF 0 C512 0 C513 1-116-717-11 1-112-867-51 CERAMIC CHIP 10uF CERAMIC 220PF 0 C513 1-112-869-41 CERAMIC 0 C514 0 C515 0 C516 1-162-968-91 1-116-874-11 1-112-869-41 CERAMIC CHIP 0.0047uF CERAMIC CHIP 10uF CERAMIC 470PF 0 C517 0 C519 1-116-034-91 1-118-587-11 FILM 0.0033uF 5% CAP, ELECT (390MF) (US, CND) 0 C519 0 C520 C522 1-118-588-11 1-112-869-41 1-115-350-51 CAP, ELECT (130MF) (AEP, UK, AUS) CERAMIC 470PF 10% CERAMIC 0.0047uF C524 C525 1-112-235-21 1-118-345-11 ELECT 330uF CERAMIC CHIP 0.01uF 20% 10% 250V 2KV (US, CND) 25V 25V C526 C527 C528 C530 C533 1-114-994-11 1-112-235-21 1-112-235-21 1-118-361-11 1-112-251-21 ELECT ELECT ELECT CERAMIC CHIP ELECT 20% 20% 20% 10% 20% 35V 25V 25V 50V 35V C534 C535 0 C537 1-112-245-21 1-126-964-11 1-116-728-11 ELECT 47uF ELECT 10uF CERAMIC CHIP 2.2uF 20% 20% 10% 35V 50V 10V (US, CND) 470PF 2200uF 330uF 330uF 0.1uF 470uF 10% 10% 250V 250V (AEP, UK, AUS) 20% 250V (US, CND) 10% 250V (AEP, UK, AUS) 20% 250V (US, CND) 10% 5% 10% 25V (AEP, UK, AUS) 20% 25V (US, CND) 20% 10V 10% 250V (AEP, UK, AUS) 10% 250V (US, CND) 10% 10% 10% 50V 35V 250V (US, CND) 400V < COMPOSITION CIRCUIT BLOCK > RB5000 RB5001 RB5002 RB5003 RB5004 86 1-234-372-11 1-234-372-11 1-234-372-11 1-234-372-11 1-234-372-11 RES, NETWORK 100 (1005X4) RES, NETWORK 100 (1005X4) RES, NETWORK 100 (1005X4) RES, NETWORK 100 (1005X4) RES, NETWORK 100 (1005X4) HT-ST7 POWER Ref. No. 0 CN501 CN503 Part No. 1-564-321-11 1-564-707-11 Description Remark < CONNECTOR > PIN, CONNECTOR (3.96 mm PITCH) 2P PIN, CONNECTOR (SMALL TYPE) 5P < DIODE > 0 0 0 0 0 D501 D502 D504 D507 D508 8-719-083-71 8-719-083-71 8-719-074-75 6-503-036-01 6-503-032-01 DIODE DIODE DIODE DIODE DIODE UDZSUSTE-1730B UDZSUSTE-1730B PTZ-TE25-30B DZ2J220M0L DZ2J180M0L 0 0 0 0 0 D511 D512 D513 D514 D516 8-719-077-77 6-503-030-01 6-501-119-01 6-501-119-01 6-502-997-01 DIODE DIODE DIODE DIODE DIODE D3SB60F3 DZ2J160M0L RR264M-400 RR264M-400 CMF02 (T2L, SONY, Q) 0 D517 0 D518 D519 D521 6-503-731-01 8-719-083-71 6-503-458-01 6-501-849-01 DIODE DIODE DIODE DIODE SARS10 UDZSUSTE-1730B RK49LF-T1 FMX-22SL Ref. No. Part No. Description 0 R531 1-216-793-91 METAL CHIP 4.7 5% 1/10W 0 R533 R534 R535 R538 R540 1-248-270-15 1-216-821-11 1-216-864-11 1-216-821-11 1-216-849-11 FUSIBLE METAL CHIP SHORT CHIP METAL CHIP METAL CHIP 0.33 1K 0 1K 220K 10% 5% 1W F 1/10W 5% 5% 1/10W 1/10W R541 R542 R543 R544 R545 1-216-864-11 1-250-632-11 1-250-628-11 1-250-640-11 1-250-652-11 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 4.7K 3.3K 10K 33K 1% 1% 1% 1% 1/10W 1/10W 1/10W 1/10W R548 1-250-616-11 METAL CHIP 1K 1% 1/10W < TRANSFORMER > 0 T501 1-697-278-11 1-523-088-11 0 TH501 1-811-315-31 1-533-217-31 1-533-217-31 FUSE (5 A/250 V) 0 VDR501 1-811-165-31 VARISTOR (TVR10471-D) ************************************************************* MISCELLANEOUS ************** FUSE HOLDER FUSE HOLDER < IC > 0 IC501 0 IC501 IC502 6-716-855-01 6-720-460-01 6-711-947-01 IC STR-Y6766 (AEP, UK, AUS) IC STR-Y6735 (US, CND) IC MM1431CURE < COIL > 0 L501 0 L502 L505 L506 1-460-618-11 1-460-618-11 1-421-918-11 1-460-612-11 COIL, LINE FILTER COIL, LINE FILTER (AEP, UK, AUS) COIL, CHOKE 10uH COIL, CHOKE 2.2uH < PHOTO COUPLER > 0 PH502 6-600-276-01 PHOTO COUPLER PS2561AL1-1-V-W < TRANSISTOR > 0 Q501 8-729-056-46 TRANSISTOR POWER THERMISTOR < VARISTOR > < FUSE HOLDER > FH501 FH502 TRANSFORMER CONVERTER < THERMISTOR > < FUSE > 0 F502 Remark 2SC5053T100Q < RESISTOR > 0 0 0 0 0 R501 R502 R515 R516 R517 1-216-864-91 1-240-938-91 1-216-864-11 1-216-793-91 1-257-117-11 SHORT CHIP METAL SHORT CHIP METAL CHIP METAL 0 1.5M 0 4.7 0.33 0 0 0 0 0 R518 R519 R520 R521 R522 1-257-117-11 1-216-793-91 1-218-855-91 1-218-887-91 1-218-881-91 METAL METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 0 0 0 R523 R525 R526 R528 1-216-829-91 1-216-845-91 1-216-809-91 1-215-929-51 METAL CHIP METAL CHIP METAL CHIP METAL OXIDE 5% 0.5W F 5% 5% 1/10W 2W F 0.33 4.7 2.2K 47K 27K 5% 5% 0.5% 0.5% 0.5% 2W F 1/10W 1/10W 1/10W 1/10W 4.7K 100K 100 100K 5% 5% 5% 5% 1/10W 1/10W 1/10W 3W F 0 AC1 0 AC1 0 AC1 BT1 0 CPA1 1-777-071-83 1-835-068-21 1-837-308-11 1-490-558-61 1-770-019-72 CORD, POWER (AEP, UK) CORD, POWER (AUS) CORD, POWER-SUPPLY (US, CND) BLUETOOTH MODULE ADAPTOR, CONVERSION PLUG 3P (UK) 0 F502 FFC1 FFC2 FFC3 FFC4 1-576-232-51 9-833-605-97 9-833-605-97 9-833-605-97 9-833-605-97 FUSE (H.B.C.) (T 5 AH/250 V) WIRE KIT (B-FFC) (14 pin) (See Note) WIRE KIT (B-FFC) (9 pin) (See Note) WIRE KIT (B-FFC) (28 pin) (See Note) WIRE KIT (B-FFC) (13 pin) (See Note) FFC5 FFC6 FFC7 NFC1 SP1 9-833-605-97 9-833-605-97 9-833-605-97 8-989-470-00 1-858-867-12 WIRE KIT (B-FFC) (8 pin) (See Note) WIRE KIT (B-FFC) (15 pin) (See Note) WIRE KIT (B-FFC) (5 pin) (See Note) RC-S801/A (NFC) LOUDSPEAKER (2 cm) (Tweeter) (L-ch) SP2 SP3 SP4 SP5 SP6 1-858-867-12 1-858-869-21 1-858-869-21 1-858-869-11 1-858-869-11 LOUDSPEAKER (2 cm) (Tweeter) (R-ch) LOUDSPEAKER (6.5 cm) (Woofer) (L-ch) LOUDSPEAKER (6.5 cm) (Woofer) (R-ch) LOUDSPEAKER (6.5 cm) (Surround) (L-ch) LOUDSPEAKER (6.5 cm) (Surround) (R-ch) SP7 SP8 SP9 SPC1 1-858-869-11 1-858-869-11 1-858-869-11 1-846-506-11 SPC2 1-846-506-21 LOUDSPEAKER (6.5 cm) (Surround Back) (L-ch) LOUDSPEAKER (6.5 cm) (Surround Back) (R-ch) LOUDSPEAKER (6.5 cm) (Center) CABLE WITH CONNECTOR (GLAY/BLACK) (for L-ch) CABLE WITH CONNECTOR (RED/BLACK) (for R-ch) SPC3 1-846-507-11 CABLE WITH CONNECTOR (4P) (for Surround L/R) CABLE WITH CONNECTOR (6P) (for Center, Surround Back L/R) ************************************************************* SPC4 1-846-508-11 Note: As for WIRE KIT (B-FFC), all flat flexible cables (Ref. No. FFC1, FFC2, FFC3, FFC4, FFC5, FFC6, FFC7) will be 1 set. 87 HT-ST7 Ref. No. Part No. 4-463-413-12 4-463-413-22 4-463-413-32 4-463-413-42 4-463-414-11 4-463-414-21 4-463-414-31 4-463-414-41 4-475-315-11 4-475-315-21 4-475-315-31 4-475-315-41 4-475-315-51 4-475-315-61 4-475-315-71 4-475-316-11 4-475-316-21 4-475-316-31 4-475-316-41 4-475-316-51 4-475-316-61 4-475-316-71 88 Description Part No. Description ACCESSORIES ************ Remark 501 502 A-1922-045-A 1-492-449-11 MANUAL, INSTRUCTION (Operating Instructions) (ENGLISH, FRENCH) (US, CND) MANUAL, INSTRUCTION (Operating Instructions) (ENGLISH) (UK, AUS) MANUAL, INSTRUCTION (Operating Instructions) (FRENCH, SPANISH, DUTCH) (AEP) MANUAL, INSTRUCTION (Operating Instructions) (GERMAN, POLISH, ITALIAN) (AEP) GUIDE, REFERENCE (Reference Guide) (ENGLISH, FRENCH) (US, CND) 503 504 505 1-837-197-31 1-759-586-61 X-2587-432-1 GRILLE ASSY (Grille frame) REMOTE COMMANDER (RM-ANU164) (Remote control) CORD, LIGHT PLUG (Digital optical cable for a TV) CONTROLLER, VIDEO (AV MOUSE) (IR blaster) FOOT (ANGLE) ASSY (1 piece) (Stand) 506 507 7-682-561-09 1-489-359-11 507 1-489-360-11 507 1-489-361-11 GUIDE, REFERENCE (Reference Guide) (ENGLISH) (UK, AUS) GUIDE, REFERENCE (Reference Guide) (FRENCH, SPANISH, DUTCH) (AEP) GUIDE, REFERENCE (Reference Guide) (GERMAN, POLISH, ITALIAN) (AEP) MANUAL, INSTRUCTION (Operating Instructions) (SWEDISH) (AEP) MANUAL, INSTRUCTION (Operating Instructions) (DANISH, FINNISH) (AEP) MANUAL, INSTRUCTION (Operating Instructions) (GREEK) (AEP) MANUAL, INSTRUCTION (Operating Instructions) (TURKISH) (AEP) MANUAL, INSTRUCTION (Operating Instructions) (SLOVAKIAN) (AEP) MANUAL, INSTRUCTION (Operating Instructions) (HUNGARIAN, CZECH) (AEP) MANUAL, INSTRUCTION (Operating Instructions) (PORTUGUESE) (AEP) GUIDE, REFERENCE (Reference Guide) (SWEDISH) (AEP) GUIDE, REFERENCE (Reference Guide) (DANISH, FINNISH) (AEP) GUIDE, REFERENCE (Reference Guide) (GREEK) (AEP) GUIDE, REFERENCE (Reference Guide) (TURKISH) (AEP) GUIDE, REFERENCE (Reference Guide) (SLOVAKIAN) (AEP) GUIDE, REFERENCE (Reference Guide) (HUNGARIAN, CZECH) (AEP) GUIDE, REFERENCE (Reference Guide) (PORTUGUESE) (AEP) Ref. No. Remark SCREW +B 4X8 (1 piece) RF MODULATOR (EZW-RT50 UC) (1 piece) (Wireless transceiver) (AEP, UK) RF MODULATOR (EZW-RT50 UC2) (1 piece) (Wireless transceiver) (US, CND) RF MODULATOR (EZW-RT50 AU) (1 piece) (Wireless transceiver) (AUS) 501 Grille frame (1) 502 Remote control (1) 503 Digital optical cable for a TV (1) 504 IR blaster (1) 505 Stands (2) 506 Screws (2) 507 Wireless transceivers (2) HT-ST7 MEMO 89 HT-ST7 REVISION HISTORY Ver. Date 1.0 2013.06 Description of Revision New How to search for a contact point of signal lines or the like in DIAGRAMS SECTION If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use the PDF file search function to find one. e.g.) If a contact point is shown as , follow the procedure below. Procedure: 1. Press the [F] key while pressing the [Ctrl] key. 2. Input “>001Z” in the search box and press the [Enter] key. 3. The relevant part (page), where the contact point is shown, appears. Note: If you still see the original page, press the [Enter] key again.
![[PDF:4.7MB]](http://vs1.manualzilla.com/store/data/005853887_1-c5fd0ffcec21d199ddeaa4c471851be4-150x150.png)
![ユーザーズマニュアル [PDF形式]](http://vs1.manualzilla.com/store/data/006555158_3-f88d9e529a353c4c16faa1297a29bfab-150x150.png)
