Download SERVICE MANUAL Serial number 1000 to 1048

SERVICE MANUAL
Serial number
1000 to 1048
X-35
PARTS
Vacuum Breaker WO1009
Check Valve WO1013
Water solenoid valve WO1011
Shut-off valve WO1001
Drain is by gravity,
using a 2 1/2” diameter
drain tube.
Main Power Switch
PP1100
N
L1
Door Switch
Eo1077
2
G
X-35
PARTS
Control Panel
Rinse-Aid Sanitizer Detergent
Chemical pumps
Priming toggle switch WO1030
Peristaltic pinch tube
White for Sanitizer and rinse-aid
Black for Detergent
Chemicals
Peristaltic Pump Base AO1001
Pump Pinch Tube AO1005
Peristaltic Pump Rotor AO1003
Peristaltic Pump Cover AO1002
Cover Screw HO1005A
Detergent:
High sequestrant
alkaline solution
200 ppm
Sanitizer:
Chlorine solution
(min. 120F, 49C) min:
50 ppm (as NaOCl)
Iodine Solution (min. 75F, 24C) min: 12.5 ppmmax: 25 ppm
Quaternary ammonium solution (min. 75F,
24C)min: 150 ppm - max:400 ppm
Rinse-Aid:
Low foam rinse-aid, surfactant isopropanol
50 ppm
See local health code for appropriate quantities
and usage.
Contact your chemical representatives for
calibration and supply.
3
Cycle Light AO1008
To fill unit
before first wash
Fill Switch
EO1006A
Start wash cycle
Manually
X-35
PARTS
EO1014
Mercury Relay
Timer
Eo1079
Eo1012
Pp1100
Eo1047
Power switch
Delay Module
Relay Contactor
Eo1009
Eo1010
4
X-35
PARTS
Drain Solenoid
Screw
Solenoid Stop So1028
Solenoid Block
So1026
Drain Solenoid
Eo1015
Solenoid Link So1027
Drain Spring Ao1013
Slotted Washer So1056
Clear Tube Ad1012
Drain Chain Ao1012
1/2” soft
Copper
Pp1052
Wash Pump
Wash Pump Motor
Eo1001
Manifold
So1001
1/4” Tubing
Hose Clamp
Eo1051
Pump Cover
AO1024B
1.5” Clear PVC Tube
Ao1030
3/8” x 5/8” TB 90 Deg.
Wo1014
1.25” Male Adaptor
Wo1017
Spring Link
Door Spring So1014
Shank
5
X-35
PARTS
Spray arms
Wash Arms
Ao1022
6
Wash Arm Bearing
with Wings
Ao1041
X-35
PARTS
Adjusting the timer on the X35
The timer on the X-35 is factory preset. Some of the
functions can be adjusted to meet your
requirements.
The following cams can adjusted;
#4 Fill-Flush
#5 Detergent pump
#6 Sanitizer Pump
#7 Rinse Additive pump
You can open or close the gap on the cams with
the special tool that was supplied with the
dishwasher.
If during a full cycle (wash - dump - fill - rinse) the
water increases too much, you can adjust this in two
ways.
1) Reduce the water pressure. Reducing the water pressure will reduce the amount
of water coming to the dishwasher.
2) Adjusting the Fill/flush
cam. You can adjust this
cam to decrease or increase
the length of time the water
solenoid remains open.
Closing the gap will reduce
the amount of water.
7
X-35
PARTS
8
X-35
PARTS
Part #
a01002
a01004
a01005
a01006
a01009
a01011
a01012
a01013
a01015
a01016
a01018
a01019
a01022
a01024a
a01024b
a01024c
a01026
A01028
A01029
a01030
a01036
A01037
A01041
ad1012
e01001
EO____
e01008
EO____
e01009
e01010
E01012
e01015
e01016a
e01017
E01018
e01047
e01051
Eo1078
pp1068
E01079
e01014
Pp1100
pp1052
s01001
S01003
S01006
S01009
s01012
S01013
s01014
9
QTY
3
1
3
2
1
1
1
1
1
11
11
11
2
1
1
1
4
3
1
1
1
2
2
1
1
1
1
1
1
1
1
1
3
1
1
1
2
1
1
1
1
1
5
1
1
1
1
2
4
2
Description
peri pump cover
round sump gasket
d/m squeeze tube
pump seal
"2"" drain ball"
spray base gasket
Sash chain
drain spring
thermometer
FEET red detergent line
FEET blue rinse line
FEET #3 clear vinyl line
"23"" spray arm"
mounting cast iron
pump cover sm cast iron
impellor open l cast iron
hex foot
"18""bucket probe"
control box lock
"12""X1 1/2"" clear sump hose"
o ring for pump
3/16 barb fitting
wing spray arm bearing
"7"" #20 vinyl line 1/2 x 3/4"
1 h.p. motor
"toggle switch / replaces eo1006,7"
indicator light
black plastic plug
insta start relay
insta start socket
90 second timer
drain solenoid
48 rpm motor
gang box
gang box cover
110 ac counter
hose clamp
door switch magnet
3/8 brass plugs
door switch module
mercury relay
30 amp switch
FEET 1/2 l copper tubing
manifold a/c machine
wrapper a machine
stand a machine
pan a machine
door a/b/c machine
lft door guide w/studs
door springs
s01015
s01018
s01019
s01020
s01021
s01022
s01025
s01026
s01027
s01028
s01029
s01034
s01035
s01037
s01041
s01042
s01044
s01046
S01048
s01056
s01050
S01049
w01001
w01003
w01005
w01008
w01009
w01011
w01013
w01014
w01017
1
2
2
2
4
1
1
1
1
1
2
1
1
1
1
2
1
1
1
2
2
1
1
3
2
1
1
1
1
1
1
door arm a machine
door link
door stop
"1"" pipe clamp"
door spacer 3/8 x 3/8
rack runner a machine
solenoid cover
solenoid block
drain solenoid link
drain solenoid stop
solenoid bars
scrap trap body
scrap trap screen
1/2' plumbing supports
chemical tube bracket
sump baffle
ss sump a/c machine
sump screen a/c machine
S.S. drain ball stem
large slotted washer
"1/2"" tube clips"
"3/8"" tube clips"
"1/2"" thrd ball valve"
1/2 close nipple brass
1/2 street 90 deg brass
1/2 x 5/8 90 deg brass
"1/2"" vacuum breaker"
"1/2"" water solenoid"
"1/2"" check valve"
3/8 nptx 5/8 tb 90 deg brass
"1 1/4"" male adapter
X-35
PARTS
BODY COMPONENTS
CODE #
16321
16322
16323
16324
16325
16326
16327
16328
16329
16330
16331
16334
16335
16336
16337
16339
16340
16341
16342
16343
16344
16431
16428
16429
16430
16432
16433
60676
60677
60678
10
QTY
1
2
1
1
2
1
1
1
1
1
1
1
2
4
2
2
1
2
2
1
4
1
1
1
1
1
1
1
1
1
DESCRIPTION
Washing tank and basement
Rack rails
Left sliding door
Right sliding door
Stopping door angle bar
Electrical components box
Electrical components box cover
Drain screen container
Drain screen container cover
Drain screen
Magnet fixing gasket
Hood handle
Connecting rod for handle
Handle fixing screws
Double thread spacer for rod
Spring hook
U-bold to fix magnet wiring
Washer for magnet
Washing tank angle bar
Detergent piper angle bar
Door sliding guides
Stainless steel washing pipe
Magnet cover
Drain screen container
Drain screen
Rod for rubber ball
Pipe for magnet wiring
Carton box packing
Pallet
Carton box for components
X35
Trouble Shooting
Dishes are coming out soapy.
Water temperature must be higher than 120F.
Unit should drain properly.
[
[
Dishes/Glasses are not clean.
Check that your washing temperature is at least 120F.
Check your water softener for proper operation.
Check the sump screen and the spray arm jets for obstruction.
[
[
[
Machine does not fill with water.
Check the water shut-off valve behind the control panel. The handle should be
parallel with the line.
[
Machine does not shut OFF.
If the dishwasher stops when the doors are opened, use the master switch, at the
back, to operate the dishwasher until service comes.
[
Machine does not stop filling up.
Close the water shut-off valve , turn power off and call for service.
[
Machine does not hold water.
Check under the drain ball for any foreign material, anything that does not belong
there.
[
Spray arms don't spin.
Check the spray arm bearing for ease of movement. Clean if required.
[
The dishwasher does not start.
Check the master switch at the back of the control panel and verify that it is in the ON
position
Check the circuit breaker which services the dishwasher and make sure it is in the ON
position.
Is the door closed completely?
[
[
[
Water comes out the doors.
Check the spray arms for missing end plug. If they are, they could be in the screen
basket.
[
11
X35
Trouble Shooting
Water is leaking on the floor.
Check the scrap accumulator filter.
If water comes out of the scrap accumulator and the filter is clean, the drain is
probably clogged.
[
[
Water does not drain from the wash tank.
Check the drain sump for obvious clogging.
Lift the plunger-ball assembly, to manually drain the dishwasher. If does not drain
rapidly (about 6 seconds) something is clogging the pipe that drops on the accumulator.
If it drains properly that the solenoid may be defective.
[
[
For service, Call:
Jet Tech Systems
1 888 275 4538
Chemical Supplier
Name____________________________________________
Telephone_____/______/___________
Representative_____________________________________
Model X 35
Serial Number: ________________
Date of install: __________/__________/___________
12