Download Titan 351 BF 140
Transcript
Service Manual for ride-on scrubber drier Titan 351 BF 140 English IP Gansow GmbH Dreherstraße 9 59425 Unna www.gansow.de [email protected] Tel.: 0049 (0)2303 2580-0 Rev 1.0 Translation of the original operating instructions Machine models TITAN 351 BF 140 IP Gansow GmbH Dreherstraße 9 D 59425 Unna www.gansow.de Machine model TITAN 351 BF 140 1. Important warnings 1.1 Important warning: Do not use this appliance without first reading the operating instructions. 1.2 Important warning: This appliance is not suitable for removing dusts hazardous to health. 1.3 Important warning: This appliance is to be used for the wet cleaning of non-textile floors only. 1.4 Important warning: This appliance is not authorised for use outdoors, on public footpaths or on highways. 1.5 Important warning: This appliance may be used on floors with a maximum slope of 12% only. IMPORTANT: Before turning or driving around corners, speed should be considerably reduced. To do this, simply exert less pressure on the accelerator. 1.6 This appliance can be switched on only when the operator is sitting in the driver's seat. The driver's seat is fitted with a microswitch which enables starting up of all functions when activated by the weight of the operator. 1.7 This appliance may be used by fully trained personnel only. 1.8 In order to prevent unauthorised use of the machine, always remove the key from the key switch. 1.9 When leaving the machine, the operator should apply the parking brake to ensure it cannot move in his absence. 1.10 When using the machine, the operator should take care not to endanger any third persons, particularly children. 1.11 Before any cleaning or servicing work is carried out on the machine and before any parts are replaced, the following precautions must be taken: the machine plug must be removed from the battery socket and the key must be removed from the key switch. Apply the parking brake whenever work is carried out on the machine. IMPORTANT: Before changing the main fuse, it is ESSENTIAL that the battery cabling is disconnected from the batteries. 1.12 We expressly draw your attention to the fact that original parts and accessories which are not supplied by us have neither been tested nor cleared by us. The installation and/or use of such items may therefore adversely affect the efficiency and characteristics of your floor cleaning machine, jeopardising its active and passive safety. The manufacturer declines all liability for damage occurring as a result of the use of non-original parts or accessories. 1.13 Under no circumstances may the charger leads (connecting the charger to the machine) supplied be modified. They must under no circumstances be prolonged. 1.14 All electrical functions of the machine are interrupted immediately as soon as the plug is inserted into the charger socket. 1.15 Caution: This appliance may only be used with the brushes supplied or with the brushes listed in the operating instructions. The safety of the appliance will be jeopardised by the use of other brushes. 1.16 Caution: Battery gas is highly explosive! Avoid sparks and open fire close to the batteries! In order to avoid the build-up of dangerous gas inside the machine, the seat above the battery compartment must be removed whilst charging is in progress. The battery cell caps must also be removed or at least unscrewed. 1.17 Important! Rooms where batteries are being charged should always be well ventilated. 1.18 Instruction 1.16 does not apply to gel batteries. 1.19 The suitable temperature for the use of the machine ranges between +4°C and +35°C; when the machine is not used, the temperature range is between +0°C e +50°C. The humidity range for the machine under any conditions varies between 30% and 95%. this product is classified as RAEE type special waste and is covered by the requisites of the new environmental protection regulations (2002/96/CE RAEE). It must be disposed of separately from ordinary waste in compliance with current legislation and standards. Special waste. Do not dispose of with ordinary waste. 2. Notes before operating 2.1 Please read the following instructions on the use of the batteries and the battery charger (included with the batteries and/or battery charger) before operating battery powered machines: 2.2 New batteries supply full capacity after the first 8 - 10 charging cycles only. During this period, the machine should not therefore be used for excessively heavy cleaning. 2.3 To protect your battery, the machine is equipped with a computer aided charge indicator (BEM). This built-in safeguard incorporates a row of eight yellow light emitting diodes (LEDs) showing the state of charge at any time (capacity indicator). Once the battery reaches the programmed permissible remaining capacity, the brush motor is automatically switched off. This is indicated by a red LED. When the battery is connected, the BEM performs a power-on self test for approximately 3 seconds. Afterwards machine operating hours are shown with a resolution of 0.1h. The capacity indicator is activated by turning the key switch to the “1” position. The lit yellow LEDs indicate the remaining capacity. approximately 10 %. Each LED corresponds to a capacity window of Once the permissible remaining capacity is reached, the left yellow LED flashes to indicate that the brush motor is about to stop. The red LED indicates that the permissible remaining capacity has been reached. At the same time the brush motor is switched off. 2.4 Before operating the machine, make sure the cowling is completely closed. 2.5 A red light on the top of the control panel indicates that the hand brake is applied. ATTENTION: The drive control is still activated when the hand brake is applied! 2.6 The driver's seat can be regulated forwards and backwards. It is also equipped with an "operator present" security device in the form of a microswitch which disables all functions when the operator gets off the seat. 2.7 The direction of motion is selected by the joystick on the left of the control panel. The direction of motion corresponds to the position of the joystick. When reversing with the squeegee lowered (in the working position), the electronic controls prevent motion until the squeegee has been completely raised. After the manoeuvre has been completed and forward motion has been resumed, the squeegee will return to the previous position. ATTENTION: The squeegee can be lowered during forward motion only. 3. Commissioning and operating the machine 3.1 The plug at the end of the charger lead (connecting the charger to the battery) should only be removed from the battery socket after the charger has gone off automatically. The plug connected to the machine should then be inserted into the battery socket. 3.2 Close the seat plate (raised during charging). 3.3 Remove the tank lid and fill the clean water tank with COLD water, preferably using a hose. To obtain the cleaning liquid, add Gansow low foam detergent. If using other brands, refer to the producer's instructions or use your experience. Finally, close the tank lid. IMPORTANT: Detergents which produce a lot of foam may greatly impair the efficiency of the machine. IMPORTANT: Make sure the gasket is free of holes, cracks or damage of any kind which could jeopardise the efficiency of the vacuum created by the motor, reducing the suction force and the quality of the cleaning obtained. 3.4 The operator must not switch on the machine before sitting in the driver's seat. 3.5 The brushes are lowered by pressing the button with the corresponding icon at the bottom left. the brushes are lowered until they touch the ground and rotate automatically at the slightest pressure on the forward motion pedal. To increase the flow of detergent to the brushes, turn clockwise to regulate the quantity (to reduce, turn anticlockwise). IMPORTANT: motion pedal. 3.6 the brushes will not turn or the detergent flow until light pressure is exerted on the forward The squeegee is lowered by pressing the button with the corresponding icon at the bottom right. it is lowered until it touches the ground, while suction is activated automatically by the lowering microswitch. IMPORTANT: when the direction of motion is reversed, the squeegee is automatically raised and suction is turned off. When forward movement is resumed, the setting is reset. 3.7 The direction of motion corresponds to the position of the joystick on the left marked with arrows indicating the movement selected. The pedal electrically controls an electronic board and is spring loaded. When it is released, it therefore springs back immediately to the zero current position. With the standard programme on the electronic board, reverse speed is half forward speed. 3.8 The brake pedal is on the left of the accelerator pedal and is an independent system. This means that, to avoid damage, it must be pressed only after the accelerator pedal has been released. IMPORTANT: Before starting work, test the service brake to verify efficiency. 3.9 The machine has a safety system (level electrodes) to switch the vacuum motor off if the foam or dirty water reach a critically high level inside the tank. IMPORTANT: If the level electrodes are triggered while operating in automatic, AUTO mode must be switched off and the tank emptied. Turn AUTO mode on again only after making sure no other functions are active. IMPORTANT: If the level electrodes are triggered while operating in manual mode and suction shuts down, the squeegee switch must be turned off and the tank emptied (or the fault resolved). 4. Instructions for use during cleaning 4.1 After switching on the machine, the operator must wait about 3 seconds before all functions are verified and ready for use. IMPORTANT: Before turning or driving around corners the speed should be reduced considerably. To do this the operator simply exerts less pressure on the accelerator. 4.2 Floors should be cleaned and dried in parallel strips overlapping by 5 - 10 cm. Our after-sales service technician or demonstrator will show you how to use your machine as efficiently as possible. 4.3 Thanks to the vacuum created inside the collection tank, the used water and dirt are completely absorbed and conveyed to the dirty water tank. In order to ensure that neither dirty water nor foam can find their way into the vacuum motor, the tank is equipped with a foam cut-off system and the intake pipe is fitted with a filter to catch fluff. This filter stops the material several centimetres above the maximum possible water level inside the tank. 4.4 When the liquid in the clean water tank has been used up or after cleaning has been completed, when not in AUTO mode, switch off the brush motor by pressing the switch with the brush icon. This automatically causes the solenoid valve to shut off the supply of detergent to the brush, switches off the pump and raises the brush unit to the rest position. Allow the machine to keep moving for another 5 or 6 m to suck up the remaining dirty water. By pressing the button with the squeegee/vacuum motor icon, the squeegee will be raised to the rest position and the vacuum motor will be turned off. 4.5 When the accelerator pedal is released, the drive motor slows down and stops. 4.6 The parking brake should be applied to prevent the machine from moving by accident. 4.7 Empty the dirty water tank into a recipient or a drain using the drain hose. Remove the cap, release the hose from the hose clip at the back of the machine and drain the fluid. 4.8 At the end of cleaning, clean the machine (without using a water jet) and rinse the tank. 4.9 Our machines are fitted with a quick brush change system. BRUSH CHANGE: 1. Make sure the brush head is raised, no function is active and the handbrake is on. 2. Take hold of the brush with both hands and turn sharply in the normal brush rotation direction (in the case of two brushes, they rotate towards the centre; in the case of three, the centre brush rotates clockwise). 3. Remove the old brushes from underneath the brush head and place the new ones as near as possible to the bayonet fitting lined up with each motor. 4. Lower the head and press the pedal lightly briefly (about 2-3 secs) 5. Switch the brushes off, raise the brush head and make sure the brushes are correctly attached. If not, then repeat operations 3, 4 and 5, making sure each brush is centred and lined up with the motor. 4.10 Before connecting the machine to the charger, make sure the key switch is off (the plug is under the seat, above the battery compartment). After 15 seconds, the charger comes on and recharging begins. Please read the instructions on use of the batteries and battery charger (included with the batteries and/or battery charger) before operating battery powered machines: In order to avoid build-up of dangerous gas inside the machine during recharging, the seat over the battery compartment must be removed whilst charging is in progress. Instruction 4.11 does not apply to gel batteries. 5. Troubleshooting 5.1 No water is delivered. • Check the water pump fuse. • Turn the delivery knob clockwise. • Clean the filter in the water tank. • Fill the clean water tank. • Check feed pipes for kinks. • Release the red emergency button • Check operation of the pump. 5.2 The vacuum motor does not start. • Check the automatic vacuum motor switch. • Clean the dirty water tank around the sensor electrodes and the electrodes themselves. • Do not move the electrodes from their original position; make sure they are not out of position. • If the distance between them, or between the electrodes and the side of the tank, is modified, the power cut-off mechanism may be activated by mistake. • Observe how much foam is generated by the detergent used. • Use Gansow´s low foam detergent. 5.3 • • • • • • 5.4 Water is not sucked up, although the vacuum motor is operating. Press the button with the "squeegee" icon. Make sure the drain hoses are closed. Check the tank lid is properly in place and lying flat on the water tank. Check the state of the tank gasket. Replace if necessary. Check on the state of the squeegee blades (see also points 5.4 and 5.5) Check that the suction tubes leading from the squeegee to the dirty water tank and the connectors inside the dirty water tank are not blocked. The squeegee with suction is leaving smears. Clean the rear squeegee blade. Check the rear squeegee blade and if necessary turn or replace. The rear squeegee blade may be used four times. • See also 5.8. • Use the wheels to adjust the height of the squeegee from the ground. • • 5.5 The squeegee is stuck to the floor. Check the state of the front squeegee blade, in particular, that the slits are not blocked. If necessary, cut 1 to 3 additional slits. • If excessively worn, turn the squeegee blades or replace them. The front squeegee blade may be used four times. • 5.6 • • • The brush motors switch off. Check the automatic switches (thermal circuit breakers). Release the red emergency button Batteries are flat, charge immediately (red LED of the BEM is on). • • The dirty water does not drain out through the hose. Remove any blockages from around the drain hose coupling in the dirty water tank. Remove any blockages in the drain hose itself. 5.7 5.8 The machine is leaving a smeary film behind it (the flow of liquid to the brush has either been cut off or greatly reduced). • Turn the delivery knob clockwise. (See also 5.1) • Clean the filters in the clean water tank. • • 5.9 • • • • • • The clean water tank is empty. Fill it. See also 5.1. The machine will not move forwards or backwards. The switch in the driver's seat is broken. Check the fuses Insert the battery plug into the machine socket. Turn key switch. Release the red emergency button Release parking brake. 6. Service and maintenance 6.1 Before any cleaning or servicing work is carried out on the machine and before any parts are replaced, the following precautions must be taken: the machine plug must be removed from the battery socket, the key must be removed from the key switch and the parking brake must be applied so the machine cannot move. When leaving the machine, the operator should apply the parking brake to ensure the machine does not move unexpectedly. IMPORTANT: 6.2 Before changing the main fuse, it is ESSENTIAL that the battery cabling is disconnected from the batteries. The level of brake fluid in the brake fluid reservoir behind the driver's seat should be checked regularly once a week and topped up if necessary. The brake fluid should be replaced completely once a year. IMPORTANT: Brake fluid is corrosive and toxic. HANDLE WITH CARE, AVOID SPILLS AND DISPOSE OF APPROPRIATELY. 6.3 The tyres should be examined at regular intervals and any foreign matter such as fragments of metal, splinters of broken glass etc should be removed. 6.4 Check the state of the squeegee blades regularly and turn or replace if worn. See also 5.4 and 5.5. 6.5 The filters in the clean water tank should be cleaned regularly at least twice a week. 6.6 The vacuum motor, water pump and solenoid valve are below the water tank. The vacuum motor ventilation slits must be checked regularly for blockages and cleaned if necessary. This is especially important when the dirt includes large amounts of fluff. 6.7 The dirty water tank should be rinsed out regularly with the drain hose open (to drain the washing water), to prevent the formation of bacteria. After finishing cleaning, leave the lid open to allow drying. IMPORTANT: After each cleaning cycle, the tank should be raised and left open in order to avoid damage to the lid gasket. 6.8 If not used for long periods, leave the machine with the battery charged and the battery plug unplugged. 6.9 A general control by authorised IPC GANSOW personnel is recommended at least once every six months. 6.10 Faulty or unused batteries should be disposed of correctly. 6.11 For more information on our branches and authorised distributors in Germany and other countries, see the list of addresses below. IMPORTANT: Rooms where batteries are being charged should always be well ventilated. 7. Extra 7.1 Rotating flash light 8. Technical data Machine model Drive motor 36 V Vacuum motor 36 V Brush motor 36 V Air circulation Vacuum max. Sound pressure Vibration level (arm) Vibration level (hand-arm) Titan 351 BF 140 1,4 kW 2 x 0,658 W 3 x 0,650 kW 2,4 m³/min 2050 mm WS 82 dB(A) < 2,5 m/sec² < 2,5 m/sec² 9. Inspection and maintenance list weekly 1. General: Check brush head Check position and condition of brushes Check the brush head is horizontal and flat when in the operating position Check clean water tank and dirty water tank for leaks Check that switches are working and lights are not blown. Check BEM (hour counter) Dismount and clean the vacuum motor Check the vacuum motor is working properly Check the squeegee blades Check the squeegee is in the correct position on the floor when suction is on Dismount suction hoses and clean Check the drive motor gearbox for leaks (if there are leaks please call the Gansow Service immediately) Check tyres for the presence of foreign matter or wear Clean bayonet and brush connection 2. Motors Check the carbon brushes of the traction motor Check the carbon brushes of the brush motor 3. Drive system Check whether the motor cables are damaged or loose Check whether the drive pedal is moving smoothly (without play) 4. Dirty water tank Clean electrodes Check outlet hose for damage Check suction pipes and hoses for blockages Check cover sealing 5. Battery Check battery cable and connectors If not used for long periods, leave the machine with the battery charged and the battery plug unplugged. Check that cell caps are safe and not damaged (does not apply to GEL batteries) Check acid level in each cell (does not apply to GEL batteries) Grease terminals (does not apply to GEL batteries) 6. Drive control unit Clean control unit (blow out with compressed air) Check that contacts are clean and weld free Check fuses Check that cable connections are firmly secured (false connections) 7. Machine control unit Clean control unit (blow out with compressed air) Check that automatic fuses are firmly in position Check connectors are firmly connected 8. Brakes Check position and effect of brake pedal and that there are no leaks Check rear brakes (no leaks) Check position and effect of parking brake 9. General inspections Have the machine checked by an electrician Have the machine serviced monthly ¼ yearly ½ yearly yearly X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X IP Gansow GmbH Dreherstraße 9 D 59425 Unna www.gansow.de March 2013 85587/85590 MODELL/MODEL: TITAN 351 BF 140 GESTELL/FRAME DATUM/DATE: 01/2013 56 01 02 12 03 04 15 16 17 13 06 09 10 20 21 19 07 22 23 24 47 46 44 37 45 36 38 33 48 51 52 53 54 35 41 40 39 34 31 25 55 30 42 50 32 43 49 18 11 08 05 14 BLATT/PAGE: 01 26 29 27 28 85587/85590 Position 0001 0001 0002 0003 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0025 0026 0027 0028 0029 0030 0031 0032 0033 Menge 2 2 1 1 1 1 1 1 1 1 1 1 1 8 8 1 1 1 1 6 6 4 2 1 1 1 1 1 1 10 1 1 3 3 2 2 2 Gestell-Frame Titan 351 BF 140 Artikel-Nr./Part No. 30604 30628 31213 30606 30629 31213 30605 30621 16901 05000 05136 05118 22929 05060 05557 30603 30610 30631 30602 05557 05060 05070 22905 16990 22916 41967 22918 60110 30611 05326 22914 22913 05060 05557 70029 05060 05557 Bezeichnung Deckel, oberer-, rot Deckel, oberer-, grün Tankdichtung Rahmen für Tank, rot Rahmen für Tank, grün Tankdichtung Schmutzwassertank Frischwassertank Batterie 36 V / 720 AH Sechskantschraube, M 8 x 16 Federring, M 8 Unterlegscheibe, M 8 Gestell Linsensenkkopfschraube, M 5 x 16 Schraubenrosette, M 5 Eckverkleidung, hinten, links Seitenverkleidung, Verlängerung, links, rot Seitenverkleidung, Verlängerung, links, grün Seitenverkleidung, links Schraubenrosette, M 5 Linsensenkkopfschraube, M 5 x 16 Flachkopfschraube, M 6 x 16 Halter für Seitenverkleidung Hupe, 36 V Klemmschiene, Dichtlippe, vorne Dichtlippe, vorne Klemmschiene, Dichtlippe, unten Fronthaube, rot Fronthaube, grün Senkkopfschraube, M 6 x 12 Fussraumplatte, links Fussraumplatte, rechts Linsensenkkopfschraube, M 5 x 16 Schraubenrosette, M 5 Frontscheinwerfer Linsensenkkopfschraube, M 5 x 16 Schraubenrosette, M 5 Blatt/Page 1 Description top lid, red top lid, green tank sealing frame for tank, red frame for tank, green tank sealing dirt water tank clean water tank Battery 36 V / 720 AH hexagonal screw, M 8 x 16 spring washer, M 8 washer, M 8 Frame raised countersunk headscrew, M 5 x collar, M 5 side cover, rear, left side cover, lengthening, left, red side cover, lengthening, left, green side cover, left collar, M 5 raised countersunk headscrew, M 5 x raised countersunk headscrew, M 6 x support for side cover Hupe, 36 V clamp rail for sealing lip, front sealing lip, front clamp rail for sealing lip, down front bonnet, red front bonnet, green countersunk headscrew, M 6 x 12 footplate, left footplate, right raised countersunk headscrew, M 5 x collar, M 5 spot light raised countersunk headscrew, M 5 x collar, M 5 bis / up to 16 16 16 16 16 ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 GESTELL/FRAME DATUM/DATE: 01/2013 56 01 02 12 03 04 15 16 17 13 06 09 10 20 21 19 07 22 23 24 47 46 44 37 45 36 38 33 48 51 52 53 54 35 41 40 39 34 31 25 55 30 42 50 32 43 49 18 11 08 05 14 BLATT/PAGE: 01 26 29 27 28 85587/85590 0034 0035 0036 0037 0038 0039 0040 0041 0042 0043 0044 0045 0046 0047 0048 0048 0049 0049 0050 0051 0052 0052 0053 0053 0054 0055 0055 0056 Titan 351 BF 140 1 1 1 2 1 1 8 8 1 2 6 6 1 1 2 2 2 2 4 4 1 1 2 2 1 1 1 1 06683 30632 41984 41969 41697 22918 12201 12865 22916 22915 05060 05557 30601 12061 30615 30633 30634 30635 05060 05557 30609 30630 30636 30637 30600 30611 41978 12062 Sicherungsfenster Abdeckplatte unterm Sitz Abdeckplatte unterm Sitz, komplett Dichtlippe, hinten Dichtlippe, vorne Klemmschiene, Dichtlippe, unten Halterung für Dichtlippe Zapfen mit Ringkopf Klemmschiene, Dichtlippe, vorne Klemmschiene, Dichtlippe, hinten Linsensenkkopfschraube, M 5 x 16 Schraubenrosette, M 5 Eckverkleidung, hinten, rechts Rücklicht, komplett, rechts Aufkleber "Titan", rot Aufkleber "Titan", grün Aufkleber "351", rot Aufkleber "351", grün Linsensenkkopfschraube, M 5 x 16 Schraubenrosette, M 5 Seitenverkleidung, Verlängerung, rechts, rot Seitenverkleidung, Verlängerung, rechts, grün Aufkleber "IPC Gansow", rot Aufkleber "IPC Gansow", grün Seitenverkleidung, rechts Frontblende, unten Frontblende komplett mit Beleuchtung Rücklicht, komplett, links Blatt/Page 2 lid for fuses cover below drivers seat cover below drivers seat, complete sealing lip, rear sealing lip, front clamp rail for sealing lip, down fixing for sealing lip snap closure clamp rail for sealing lip, front clamp rail for sealing lip, rear raised countersunk headscrew, M 5 x 16 collar, M 5 side cover, rear, right backlight, complete, right Aufkleber "Titan", red Aufkleber "Titan", green Aufkleber "351", red Aufkleber "351", green raised countersunk headscrew, M 5 x 16 collar, M 5 side cover, lengthening, right, red side cover, lengthening, right, green Aufkleber "IPC Gansow", red Aufkleber "IPC Gansow", green side cover, right front cover, down front cover with spot lights backlight, complete, left Gestell-Frame 85587/85590 MODELL/MODEL: TITAN 351 BF 140 HAUBE/BONET 20 05 21 13 07 02 BLATT/PAGE: 02 04 06 03 DATUM/DATE: 01/2013 14 12 01 08 09 10 11 15 22 16 23 28 17 18 19 27 26 25 24 29 30 31 32 33 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 Menge 2 2 2 2 4 2 1 4 4 4 2 1 1 1 8 8 16 8 8 8 1 1 1 1 2 2 1 4 2 1 1 1 2 1 Haube-Bonet Titan 351 BF 140 Artikel-Nr./Part No. 05006 05136 05118 13692 05094 05118 22953 05006 05136 05118 22934 16956 16902 70124 05014 05118 05116 05118 05220 05363 05218 05119 05119 05085 05008 05119 13940 05119 05218 05085 05119 13192 05119 05218 Bezeichnung Sechskantschraube, M 8 x 25 Federring, M 8 Unterlegscheibe, M 8 Gummipuffer Mutter, M 8 Unterlegscheibe, M 8 Sitzschalenauflage Sechskantschraube, M 8 x 25 Federring, M 8 Unterlegscheibe, M 8 Scharnier für Sitzschale Sitzschale, rot Sitzschale, grün Fahrersitz Sechskantschraube, M 8 x 30 Unterlegscheibe, M 8 Unterlegscheibe, M 10 Unterlegscheibe, M 8 Mutter, M 8, selbstsichernd Kappe für Sechskantmutter, M 8 Mutter, M 6, selbstsichernd Unterlegscheibe, M 6 Unterlegscheibe, M 6 Ösenschraube, M 6 x 15 Sechskantschraube, M 6 x 25 Unterlegscheibe, M 6 Gasdruckfeder, 150 N Unterlegscheibe, M 6 Mutter, M 6, selbstsichernd Ösenschraube, M 6 x 15 Unterlegscheibe, M 6 Abstandshülse Unterlegscheibe, M 6 Mutter, M 6, selbstsichernd Description hexagonal screw, M 8 x 25 spring washer, M 8 washer, M 8 bumper nut, M 8 washer, M 8 support for seat shell hexagonal screw, M 8 x 25 spring washer, M 8 washer, M 8 hinge for seat shell drivers seat, red drivers seat green drivers seat hexagonal screw, M 8 x 30 washer, M 8 washer, M 10 washer, M 8 self-locking nut, M 8 cap for hexagonal nut, M 8 self-locking nut, M 6 washer, M 6 washer, M 6 eyebolt, M 6 x 15 hexagonal screw, M 6 x 25 washer, M 6 gas pressure spring, 150 N washer, M 6 self-locking nut, M 6 eyebolt, M 6 x 15 washer, M 6 spacer washer, M 6 self-locking nut, M 6 Blatt/Page 3 bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 05 TANK/TANK DATUM/DATE: 01/2013 19 16 15 03 02 18 14 13 22 23 12 01 06 20 21 17 04 BLATT/PAGE: 03 24 11 25 10 26 07 08 29 09 28 27 32 31 30 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 Menge 1 1 1 1 1 1 2 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 2 1 Titan 351 BF 140 Artikel-Nr./Part No. 41983 12124 11642 30116 12298 11642 01549 41960 41985 01549 11642 30638 01733 13382 40987 30639 31213 30605 30640 31213 30621 01385 01783 01705 12747 16955 01549 16955 01549 05392 05218 22959 Bezeichnung Tank, Schmutzwasser-, komplett Winkel, 90 Grad Rohr, 50 mm Krümmer, 90 Grad Ansaugfilter Rohr, 50 mm Schlauchschelle Schlauch, Saug-, Turbine-Tank, Schlauch, Saug-, Saugfuss-Tank, Schlauchschelle Rohr, 50 mm Krümmer, groß, 90 Grad Elektrodenverschraubung Elektrodendichtung Elektroden, Satz Verstärkung, Schmutzwassertank Tankdichtung Schmutzwassertank Verstärkung, Frischwassertank Tankdichtung Frischwassertank Sieb Schlauchtülle, 1/2" Wasserschlauch Rohrschelle Ablasschlauch Schlauchschelle Ablasschlauch Schlauchschelle Schlossschraube, M 6 x 20 Mutter, M 6, selbstsichernd Schmutzwassersieb Description dirt water tank, complete elbow, 90 degree tube, 50 mm elbow, 90 degree suction filter tube, 50 mm tube clip suction hose, turbine-tank suction hose, squeegee-tank tube clip tube, 50 mm big elbow, 90 degree probe holder probe sealing probe, set dirt water tank strengthening tank sealing dirt water tank clean water tank strengthening tank sealing clean water tank sieve hose liner, 1/2" water hose hose clip drain hose tube clip drain hose tube clip closed screw, M 6 x 20 self-locking nut, M 6 sieve for dirt water Blatt/Page 4 Wassertank-Tank bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 HECK/REAR DATUM/DATE: 01/2013 BLATT/PAGE: 04 04 03 01 05 06 02 10 13 12 11 09 08 07 85587/85590 Position 0001 0002 0003 0004 0005 0005 0006 0007 0008 0009 0010 0011 0012 0013 Menge Artikel-Nr./Part No. 4 05008 4 05131 1 22943 1 22943 1 30607 1 30619 1 30616 1 16955 2 12747 2 01549 1 16955 2 05067 2 30618 2 05220 Titan 351 BF 140 Bezeichnung Sechskantschraube, M 6 x 25 Federring, M 6 Halter, Seitenverkleidung, hinten Halter, Seitenverkleidung, hinten Hecktür, rot Hecktür, grün Aufkleber, "www.gansow.de" Ablaßschlauch, 1120 mm Rohrschelle Schlauchschelle Ablaßschlauch, 1120 mm Linsensenkkopfschraube, M 8 x 30 Abstandshalter, Hecktür Mutter, M 8, selbstsichernd Blatt/Page 5 Description hexagonal screw, M 6 x 25 spring washer, M 6 support, rear side cover support, rear side cover rear door, red rear door, green sticker, "www.gansow.de" drain hose, 1120 mm hose clip tube clip drain hose, 1120 mm raised countersunk headscrew, M 8 x 30 spacer, rear door self-locking nut, M 8 Heck-Rear bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 BREMSE/BRAKE + GASPEDAL/DRIVE PEDAL 01 02 07 33 32 DATUM/DATE: 01/2013 08 34 09 10 BLATT/PAGE: 05 11 12 06 35 20 36 41 42 03 43 04 17 05 40 37 39 18 19 16 13 14 15 24 38 30 31 29 28 27 26 25 21 22 23 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 Menge 1 1 3 3 3 1 8 8 8 16 8 1 20 40 20 1 1 2 1 2 1 1 1 1 1 4 4 2 2 2 1 2 1 2 2 2 2 Titan 351 BF 140 Artikel-Nr./Part No. 71656 16199 05119 05131 05259 13178 05365 05223 05144 05126 05450 13178 05097 05116 05015 11351 12007 12273 12006 12002 11220 12361 11257 12379 11341 12010 12009 12012 12011 11219 11220 11219 30500 05008 05119 05131 05096 Bezeichnung Fahrpedal Pedal Unterlegscheibe, M 6 Federring, M 6 Sechskantschraube, M 6 x 16 Achsstummel, rechts Kappe für Sechskantmutter, M 12 Mutter, M 12 Federring, M 12 Unterlegscheibe, M 12 Sechskantschraube, M 12 x 40 Achsstummel, links Mutter, M 10 Unterlegscheibe, M 10 Sechskantschraube, M 10 x 20 Bremstrommel Bremsbacke, links Bremsbacke, komplett Bremsbacke, rechts Bremszylinder Radbandage Bremsleitung, hinten, links Verteiler Bremsleitung Bremsleitung, vorne Bremsleitung, hinten, rechts Druckfeder Zugfeder Kappe für Kronenmutter Kronenmutter, M 24 Felgenhälfte Radbandage Felgenhälfte Bremspedal Sechskantschraube, M 6 x 25 Unterlegscheibe, M 6 Federring, M 6 Mutter, M 6 Blatt/Page 6 Description accelerator pedal pedal washer, M 6 spring washer, M 6 hexagonal screw, M 6 x 16 axle, right cap for hexagonal nut, M 12 nut, M 12 spring washer, M 12 washer, M 12 hexagonal screw, M 12 x 40 axle, left nut, M 10 washer, M 10 hexagonal screw, M 10 x 20 drum brake brake shoe, left brake shoe, complete brake shoe, right brake cylinder wheel brake line, rear, left brake line divider brake line, front brake line, rear, right compression spring tension spring cap for crown nut crown nut, M 24 rim-half wheel rim-half brake pedal hexagonal screw, M 6 x 25 washer, M 6 spring washer, M 6 nut, M 6 Bremse-Brake_Pedal bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 BREMSE/BRAKE + GASPEDAL/DRIVE PEDAL 01 02 07 33 32 DATUM/DATE: 01/2013 08 34 09 10 BLATT/PAGE: 05 11 12 06 35 20 36 41 42 03 43 04 17 05 40 37 39 18 19 16 13 14 15 24 38 30 31 29 28 27 26 25 21 22 23 85587/85590 0037 0038 0039 0040 0041 0042 0043 Titan 351 BF 140 1 1 1 1 2 2 2 12542 CMCV00007 05101 11251 05097 05133 05015 Gabelterminal, M 10 Clip, M 10 Mutter, M 10 Hauptbremszylinder Mutter, M 10 Federring, M 10 Sechskantschraube, M 10 x 20 fork terminal, M 10 clamp, M 10 nut, M 10 main brake cylinder nut, M 10 spring washer, M 10 hexagonal screw, M 10 x 20 Blatt/Page 7 Bremse-Brake_Pedal 85587/85590 MODELL/MODEL: TITAN 351 BF 140 RAMMSCHUTZ/SIDE PROTECTION DATUM/DATE: 01/2013 BLATT/PAGE: 06 02 12 09 01 10 11 15 35 31 30 32 34 03 08 04 07 05 06 16 17 33 29 28 20 27 22 23 26 25 24 21 14 13 18 19 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 Menge 1 1 2 2 2 2 2 2 6 6 6 2 4 4 1 1 12 12 12 1 1 1 1 4 4 1 1 1 4 4 2 4 2 2 4 Titan 351 BF 140 Artikel-Nr./Part No. 30622 30623 22911 13773 05276 05259 05131 05119 05450 05144 05126 22922 05259 05131 22923 30624 05118 05136 05229 30625 30626 22923 30613 05229 05118 30612 22924 30627 05014 05136 05269 05116 05219 22925 05321 Bezeichnung Rammschutz, hinten, rechts Rammschutz, hinten, links Anschlag für Bürstenkopf Stopper Sechskantschraube, M 10 x 100 Sechskantschraube, M 6 x 16 Federring, M 6 Unterlegscheibe, M 6 Sechskantschraube, M 12 x 40 Federring, M 12 Unterlegscheibe, M 12 Halteplatte für Parallelogramm Sechskantschraube, M 6 x 16 Federring, M 6 Anschlag, Parallelogramm Rammschutz, vorne, links Unterlegscheibe, M 8 Federring, M 8 Zylinderkopfschraube, M 8 x 30 ISKT Rammschutz, vorne Rammschutz, vorne, rechts Anschlag, Parallelogramm Blende, hinten, links Zylinderkopfschraube, M 8 x 30 ISKT Unterlegscheibe, M 8 Blende, hinten, rechts Anfahrschutz, hinten Rammschutz, hinten Sechskantschraube, M 8 x 30 Federring, M 8 Sechskantschraube, M 10 x 30 Unterlegscheibe, M 10 Mutter, M 10, selbstsichernd Trittplatte Senkkopfschraube, M 6 x 20 Blatt/Page 8 Description protection, rear, right protection, rear, left limitation for brush head bumper hexagonal screw, M 10 x 100 hexagonal screw, M 6 x 16 spring washer, M 6 washer, M 6 hexagonal screw, M 12 x 40 spring washer, M 12 washer, M 12 holding plate for parallelogram hexagonal screw, M 6 x 16 spring washer, M 6 unlockking guard for parallelogram protection, front, left washer, M 8 spring washer, M 8 allen cap screw, M 8 x 30 protection, front protection, front, right unlockking guard for parallelogram cover, rear, left allen cap screw, M 8 x 30 washer, M 8 cover, rear, right rear bumper rear protection hexagonal screw, M 8 x 30 spring washer, M 8 hexagonal screw, M 10 x 30 washer, M 10 self-locking nut, M 10 foot plate countersunk headscrew, M 6 x 20 Rammschutz-Side Protection bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 LENKUNG/STEERING UNIT 01 DATUM/DATE: 01/2013 17 BLATT/PAGE: 07 18 10 11 01 19 12 02 20 07 08 09 03 21 13 04 14 05 15 06 16 22 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 Menge 1 1 1 1 1 1 4 4 4 2 2 1 1 4 4 4 4 1 1 4 1 1 Titan 351 BF 140 Artikel-Nr./Part No. 70010 12011 70404 41586 70011 70008 05002 05136 05118 05002 05220 70007 60035 05002 05136 05118 05545 16700 22950 05449 16989 16431 Bezeichnung Lenkraddeckel Kronenmutter, M 24 Lenkrad Multifunktionsschalter Faltenbalg Lenksäule Sechskantschraube, M 8 x 20 Federring, M 8 Unterlegscheibe, M 8 Sechskantschraube, M 8 x 20 Mutter, M 8, selbstsichernd Kreuzgelenk Ständer, Lenksäule Sechskantschraube, M 8 x 20 Federring, M 8 Unterlegscheibe, M 8 Zylinderkopfschraube, M 12 x 30 ISKT Radaufnahme, Gegenstück Radaufnahme Zylinderkopfschraube, M 10 x 20 ISKT Radbandage Fahrmotor, 36 V Blatt/Page 9 Description cap for steering wheel crown nut, M 24 steering wheel multi switch siphon steering column hexagonal screw, M 8 x 20 spring washer, M 8 washer, M 8 hexagonal screw, M 8 x 20 self-locking nut, M 8 cardan joint support, steering shaft hexagonal screw, M 8 x 20 spring washer, M 8 washer, M 8 allen cap screw, M 12 x 30 counter part for wheel support wheel support allen cap screw, M 10 x 20 wheel tire drive motor. 36 V Lenkung-Steering Unit 1 bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 LENKUNG/STEERING UNIT 02 DATUM/DATE: 01/2013 BLATT/PAGE: 08 14 15 12 11 10 04 31 17 18 20 19 21 08 07 33 32 30 09 06 05 13 16 27 29 28 34 35 36 37 38 26 22 25 24 23 39 03 02 01 40 41 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037 Menge 8 8 8 8 8 8 2 1 1 1 2 1 2 3 3 1 1 1 1 8 8 1 1 1 1 1 1 4 4 2 2 1 1 2 2 2 3 Titan 351 BF 140 Artikel-Nr./Part No. 05014 05136 05118 05118 05136 05014 14080 01717 05195 70007 05002 14533 05220 05014 05136 14062 16410 16409 16410 05014 05136 14062 60567 14534 60572 14287 70990 05596 05130 14645 14647 14062 30608 05118 05136 05014 05014 Bezeichnung Sechskantschraube, M 8 x 30 Federring, M 8 Unterlegscheibe, M 8 Unterlegscheibe, M 8 Federring, M 8 Sechskantschraube, M 8 x 30 Schiene, Gummi/Metal Kugellager Sprengring, 17 x 1 mm Kreuzgelenk Sechskantschraube, M 8 x 20 Welle für Lenkgetriebe Mutter, M 8, selbstsichernd Sechskantschraube, M 8 x 30 Federring, M 8 Lenkgetriebe Kugellager, Lenkgetriebe Zwischenring, Lenkgetriebe Kugellager, Lenkgetriebe Sechskantschraube, M 8 x 30 Federring, M 8 Lenkgetriebe Zahnrad für Lenkgetriebe Ritzel für Lenkgetriebe Doppelkette für Lenkgetriebe Kettenschloss für Doppelkette Verlängerung für Doppelkette Sechskantschraube, M 5 x 45 Federring, M 5 Kettenspanner Lagerbock für Kettenspanner Lenkgetriebe Abdeckung, Lenkgetriebe Unterlegscheibe, M 8 Federring, M 8 Sechskantschraube, M 8 x 30 Sechskantschraube, M 8 x 30 Description hexagonal screw, M 8 x 30 spring washer, M 8 washer, M 8 washer, M 8 spring washer, M 8 hexagonal screw, M 8 x 30 rubber/metal rail ball bearing circlip, 17 x 1 mm cardan joint hexagonal screw, M 8 x 20 Shaft for steering gear self-locking nut, M 8 hexagonal screw, M 8 x 30 spring washer, M 8 steering gear ball bearing, steering gear distance piece, steering gear ball bearing, steering gear hexagonal screw, M 8 x 30 spring washer, M 8 steering gear big pinion for steering gear pinion for steering gear double chain for steering gear lock for double chain extension for double chain hexagonal screw, M 5 x 45 spring washer, M 5 chain adjuster support for chain adjuster steering gear cover, steering gear washer, M 8 spring washer, M 8 hexagonal screw, M 8 x 30 hexagonal screw, M 8 x 30 Blatt/Page 10 Lenkung-Steering Unit 2 bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 LENKUNG/STEERING UNIT 02 DATUM/DATE: 01/2013 BLATT/PAGE: 08 14 15 12 11 10 04 31 17 18 20 19 21 08 07 33 32 30 09 06 05 13 16 27 29 28 34 35 36 37 38 26 22 25 24 23 39 03 02 01 40 41 85587/85590 0038 0039 0040 0041 Titan 351 BF 140 3 1 4 4 05136 14062 05136 05300 Federring, M 8 Lenkgetriebe Federring, M 8 Zylinderkopfschraube, M 8 x 20 ISKT Blatt/Page 11 spring washer, M 8 steering gear spring washer, M 8 allen cap screw, M 80 x 20 Lenkung-Steering Unit 2 85587/85590 MODELL/MODEL: TITAN 351 BF 140 FESTSTELLBREMSE/PARKING BRAKE DATUM/DATE: 01/2013 BLATT/PAGE: 09 01 05 22 04 03 06 02 21 20 19 31 18 17 30 29 07 16 15 14 10 09 08 11 12 13 28 27 26 23 25 24 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 Menge 1 2 2 2 2 1 2 1 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Titan 351 BF 140 Artikel-Nr./Part No. 16384 05479 05002 05136 05118 14182 75143 06974 05129 05090 05109 05129 75143 05096 05131 05119 05119 05096 05094 22951 12045 13259 22952 05096 05131 05119 05119 05096 05094 12045 13301 Bezeichnung Haube für Handbremse, Linsensenkkopfschraube, M 5 x 20 Sechskantschraube, M 8 x 20 Federring, M 8 Unterlegscheibe, M 8 Handbremshebel Zylinderkopfschraube, M 4 x 25 Mikroschalter mit hebel Federring, M 4 Mutter, M 4 Unterlegscheibe, M 4 Federring, M 4 Zylinderkopfschraube, M 4 x 25 Mutter, M 6 Federring, M 6 Unterlegscheibe, M 6 Unterlegscheibe, M 6 Mutter, M 6 Mutter, M 8 Verbindungsplatte Mantel für Bremsseil Bremsseil, links Bremshebelverlängerung Mutter, M 6 Federring, M 6 Unterlegscheibe, M 6 Unterlegscheibe, M 6 Mutter, M 6 Mutter, M 8 Mantel für Bremsseil Bremsseil, rechts Blatt/Page 12 Feststellbremse-Parking Brake Description cover for handbrake raised countersunk headscrew, M 5 x 20 hexagonal screw, M 8 x 20 spring washer, M 8 washer, M 8 lever for parking brake allen cap screw, M 4 x 25 microswitch with lever spring washer, M 4 nut, M 4 washer, M 4 spring washer, M 4 allen cap screw, M 4 x 25 nut, M 6 spring washer, M 6 washer, M 6 washer, M 6 nut, M 6 nut, M 8 connection plate brake cable jacket brake cable, left brake lever extension nut, M 6 spring washer, M 6 washer, M 6 washer, M 6 nut, M 6 nut, M 8 brake cable jacket brake cable, right bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 TURBINE/TURBINE DATUM/DATE: 01/2013 BLATT/PAGE: 10 18 06 07 11 08 10 04 01 02 03 17 14 05 09 12 13 15 16 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 Menge 8 8 8 2 2 4 4 4 2 2 1 8 8 2 4 2 1 1 Titan 351 BF 140 Artikel-Nr./Part No. 05218 05119 05127 30176 01081 05050 05090 05216 13958 01448 22946 05119 05013 05220 05118 05014 01549 41960 Bezeichnung Mutter, M 6, selbstsichernd Unterlegscheibe, M 6 Karosseriescheibe, 30x6x1,25mm Gehäuse, Turbinen-, Stecker, Flach-, 50 A, schwarz Senkkopfschraube, M 4 x 16 Mutter, M 4 Mutter, M 4, selbstsichernd Turbine, 36 V Dichtungsring für Turbine Halter, Saugturbinen-, Unterlegscheibe, M 6 Sechskantschraube, M 6 x 30 Mutter, M 8, selbstsichernd Unterlegscheibe, M 8 Sechskantschraube, M 8 x 30 Schlauchschelle Schlauch, Saug-, Turbine-Tank, Blatt/Page 13 Description self-locking nut, M 6 washer, M 6 coach body disc, 30x6x1,25mm turbine bonnet Plug, flat, 50 A, black countersunk headscrew, M 4 x 16 nut, M 4 self-locking nut, M 4 turbine, 36 V sealing ring for turbine turbine support washer, M 6 hexagonal screw, M 6 x 30 self-locking nut, M 8 washer, M 8 hexagonal screw, M 8 x 30 tube clip suction hose, turbine-tank Turbine-Turbine bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 BUERSTENKOPF/BRUSH HEAD 1 DATUM/DATE: 01/2013 BLATT/PAGE: 11 18 19 01 20 02 03 04 15 17 16 23 15 09 10 11 07 08 34 12 33 13 32 14 25 36 35 22 23 24 05 06 21 26 27 28 29 30 31 16 24 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 Menge 3 3 3 1 1 1 2 1 3 3 9 3 3 3 8 8 2 2 2 2 8 8 4 6 3 3 3 3 12 12 12 24 24 48 24 24 Titan 351 BF 140 Artikel-Nr./Part No. 05303 12370 12468 22933 41972 05020 05118 05220 12212 13925 05436 13256 05390 19265 05489 05285 22922 13494 13493 05486 05285 05489 13431 13430 01081 14409 12144 01600 05118 05136 05271 05271 05136 05118 05220 05363 Bezeichnung Zylinderkopfschraube, M 12 x 40 ISKT Ablenkrolle Abstandshülse Bürstenkopfronde Spritzgummi Sechskantschraube, M 8 x 50 Unterlegscheibe, M 8 Mutter, M 8, selbstsichernd Zwischenring Bajonettkupplung Spanplattenschraube, M 3 x 25 Wasserleitring Seegerring, 25 x 1,2 mm Brürste, PPN 0,5 mm Mutter, M 16 Federring, M 16 Halteplatte für Parallelogramm Winkelgelenk, M 16, links Gewindestange, M 16, links Spannschloss, M 16 Federring, M 16 Mutter, M 16 Gewindestange, M 16, rechts Winkelgelenk, M 16, rechts Stecker, 50 A, schwarz Motor, 36 V Passfeder, 8 x 7 x 56 mm Vulkollanflansch Unterlegscheibe, M 8 Federring, M 8 Sechskantschraube, M 8 x 30 Sechskantschraube, M 8 x 30 Federring, M 8 Unterlegscheibe, M 8 Mutter, M 8, selbstsichernd Kappe für Sechskantmutter, M 8 Blatt/Page 14 Description allen cap screw, M 12 x 40 guide roller spacer brush head plate splash skirt hexagonal screw, M 8 x 50 washer, M 8 self-locking nut, M 8 distance washer bayonett coupling wood plate screw, M 3 x 25 water guiding ring circlip, 25 x 1,2 mm brush, PPN 0,5 mm nut, M 16 spring washer, M 16 holding plate for parallelogram angel joint, M 16, left threader rod, M 16, right turnbuckle, M 16 spring washer, M 16 nut, M 16 threader rod, M 16, right angel joint, M 16, right plug, 50 a, black motor, 36 V key, 8 x 7 x 56 mm vulkollan flange washer, M 8 spring washer, M 8 hexagonal screw, M 8 x 30 hexagonal screw, M 8 x 30 spring washer, M 8 washer, M 8 self-locking nut, M 8 cap for hexagonal nut, M 8 Bürstenkopf-Brush Head 1 bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 22 01 02 BUERSTENKOPF/BRUSH HEAD 2 DATUM/DATE: 01/2013 29 23 30 03 24 25 04 05 31 32 26 09 27 06 07 08 21 10 11 14 13 BLATT/PAGE: 12 20 19 18 36 14 37 15 16 17 33 28 35 12 14 34 85587/85590 Position 0001 0002 0003 0004 0005 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037 Menge 2 2 1 2 2 1 1 3 2 1 1 1 4 1 1 2 1 1 1 1 1 1 1 1 1 1 1 4 4 8 4 4 1 1 1 1 Titan 351 BF 140 Artikel-Nr./Part No. 05014 05118 22926 05118 05220 01677 05116 05116 13192 05116 22347 01677 05116 16708 22927 22347 05275 05116 05116 05219 05219 05116 05116 13871 05116 05116 05275 05363 05220 05118 05136 05271 22932 16706 22960 16706 Bezeichnung Sechskantschraube, M 8 x 30 Unterlegscheibe, M 8 Halter, Stellmotor, Bürstenkopf Unterlegscheibe, M 8 Mutter, M 8, selbstsichernd Federstecker, 3,2 mm Unterlegscheibe, M 10 Unterlegscheibe, M 10 Abstandshülse Unterlegscheibe, M 10 Bolzen, 10 x 110 mm Federstecker, 3,2 mm Unterlegscheibe, M 10 Rolle, Stellmotor, Bürstenkopf Rollenhalter Bolzen, 10 x 110 mm Sechskantschraube, M 10 x 65 Unterlegscheibe, M 10 Unterlegscheibe, M 10 Mutter, M 10, selbstsichernd Mutter, M 10, selbstsichernd Unterlegscheibe, M 10 Unterlegscheibe, M 10 Stellmotor, 36 V Unterlegscheibe, M 10 Unterlegscheibe, M 10 Sechskantschraube, M 10 x 65 Kappe für Sechskantmutter, M 8 Mutter, M 8, selbstsichernd Unterlegscheibe, M 8 Federring, M 8 Sechskantschraube, M 8 x 30 Bürstenkopfaufnahme Zugfeder Halter, Zugfeder-, Zugfeder Description hexagonal screw, M 8 x 30 washer, M 8 actuator support, brush head washer, M 8 self-locking nut, M 8 spring clip, 3,2 mm washer, M 10 washer, M 10 spacer washer, M 10 bolt, 10 x 110 mm spring clip, 3,2 mm washer, M 10 roller, actuator, brush head roller support bolt, 10 x 110 mm hexagonal screw, M 10 x 65 washer, M 10 washer, M 10 self-locking nut, M 10 self-locking nut, M 10 washer, M 10 washer, M 10 actuator, 36 V washer, M 10 washer, M 10 hexagonal screw, M 10 x 65 cap for hexagonal nut, M 8 self-locking nut, M 8 washer, M 8 spring washer, M 8 hexagonal screw, M 8 x 30 brush head support tension spring tension spring support tension spring Blatt/Page 15 Bürstenkopf-Brush Head 2 bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 01 SAUGFUSS/SQUEEGEE 11 02 BLATT/PAGE: 13 17 12 03 DATUM/DATE: 01/2013 18 13 07 14 19 04 15 20 05 16 08 09 36 22 21 23 35 25 24 10 30 26 27 34 33 37 32 31 06 29 28 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037 Menge 2 2 2 2 2 2 2 2 2 2 4 2 2 2 2 2 2 2 4 2 1 1 1 1 1 1 1 6 6 1 4 4 4 4 6 6 1 Titan 351 BF 140 Artikel-Nr./Part No. 05220 05118 22956 05118 MLML49422 05448 05218 05119 05119 05260 05101 05116 05116 05101 05276 14400 05089 05106 RTRT00510 05106 41963 22902 16954 22954 22900 16953 22901 05003 05242 22955 05271 05242 05242 05518 05242 05003 22906 Bezeichnung Mutter, M 8, selbstsichernd Unterlegscheibe, M 8 Halter für Stützrolle Unterlegscheibe, M 8 Feder an Stützrolle Schlossschraube, M 8 x 50 Mutter, M 6, selbstsichernd Unterlegscheibe, M 6 Unterlegscheibe, M 6 Sechskantschraube, M 6 x 50 Mutter, M 10 Unterlegscheibe, M 10 Unterlegscheibe, M 10 Mutter, M 10 Sechskantschraube, M 10 x 100, VA Doppellenkrolle Mutter, M 14 Unterlegscheibe, M 14 Ablenkrolle Unterlegscheibe, M 14 Saugfuss, komplett Klemmwinkel, hinten Sauglippe, hinten Abweiser, links Saugfusskörper Sauglippe, vorne Klemmwinkel, vorne Sechskantschraube, M 8 x 25, VA Unterlegscheibe, M 8, VA Abweiser, rechts Sechskantschraube, M 8 x 30, VA Unterlegscheibe, M 8, VA Unterlegscheibe, M 8, VA Mutter, M 8, selbstsichernd, VA Unterlegscheibe, M 8, VA Sechskantschraube, M 8 x 25, VA Saugfussaufnahme Blatt/Page 16 Description self-locking nut, M 8 washer, M 8 support for squeegee wheel washer, M 8 spring for squeegee wheel closed screw, M 8 x 50 self-locking nut, M 6 washer, M 6 washer, M 6 hexagonal screw, M 6 x 50 nut, M 10 washer, M 10 washer, M 10 nut, M 10 hexagonal screw, M 10 x 100, stainless steel double caster wheel nut, M 14 washer, M 14 guiding roller washer, M 14 squeegee, complete clamp rail, rear squeegee blade, rear deflector, left squeegee body squeegee blade, front clamp rail. Front hexagonal screw, M 8 x 25, stainless steel washer, M 8, stainless steel deflector, right hexagonal screw, M 8 x 30, stainless steel washer, M 8, stainless steel washer, M 8, stainless steel self-locking nut, M 8, stainless steel washer, M 8, stainless steel hexagonal screw, M 8 x 25, stainless steel squeegee support Saugfuss-Squeegee bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 SAUGFUSSAUFHAENGUNG/SQUEEGEE SUPPORT 01 02 03 04 11 08 09 DATUM/DATE: 01/2013 05 17 06 07 13 16 17 20 23 42 14 39 40 41 19 18 12 10 BLATT/PAGE: 14 24 15 25 26 27 22 28 21 29 32 38 33 37 34 36 35 31 30 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037 Menge 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 1 3 1 3 1 1 1 1 2 1 1 2 1 2 1 1 1 1 SF.Aufhängung-Squeegee Support Titan 351 BF 140 Artikel-Nr./Part No. 70040 05116 12283 05116 05101 05133 16703 05269 05116 05146 05116 05219 22907 16702 01677 22347 05116 16707 01677 01677 05116 22909 05116 08430 05127 05008 05275 05116 05219 05219 05116 14280 05116 05275 01677 16701 16704 Bezeichnung Sternmutter, M 10 Unterlegscheibe, M 10 Gewindestange, M 10 Unterlegscheibe, M 10 Mutter, M 10 Federring, M 10 Gabelterminal, M 10 Sechskantschraube, M 10 x 30 Unterlegscheibe, M 10 Karosseriescheibe, 30 x 10,5 mm Unterlegscheibe, M 10 Mutter, M 10, selbstsichernd Halter, Saugfusseinstellung Feder, Saugfusseinstellung Federstecker, 3,2 mm Bolzen, 10 x 110 mm Unterlegscheibe, M 10 Rolle, Stellmotor, Saugfuss Federstecker, 3,2 mm Federstecker, 3,2 mm Unterlegscheibe, M 10 Rollenhalter, Stellmotor, Saugfuß Unterlegscheibe, M 10 Antistatikband Karosseriescheibe, 30 x 6,5 mm Sechskantschraube, M 6 x 25 Sechskantschraube, M 10 x 65 Unterlegscheibe, M 10 Mutter, M 10, selbstsichernd Mutter, M 10, selbstsichernd Unterlegscheibe, M 10 Stellmotor, 36 V Unterlegscheibe, M 10 Sechskantschraube, M 10 x 65 Federstecker, 3,2 mm Kugellkopf, Saugfussaufnahme Federring, M 20 Blatt/Page 17 Description starwheel, M 10 washer, M 10 threader rod, M 10 washer, M 10 nut, M 10 spring washer, M 10 two-way beeches, M 10 hexagonal screw, M 10 x 30 washer, M 10 coach body disc, 30 x 10,5 mm washer, M 10 self-locking nut, M 10 support, squeegee adjustment spring for squeegee adjustment spring clip, 3,2 mm bolt, 10 x 110 mm washer, M 10 roller, actuator, squeegee spring clip, 3,2 mm spring clip, 3,2 mm washer, M 10 support, squeegee actuator roller washer, M 10 antistatic device coach body disc, 30 x 6,5 mm hexagonal screw, M 6 x 25 hexagonal screw, M 10 x 65 washer, M 10 self-locking nut, M 10 self-locking nut, M 10 washer, M 10 actuator, 36 V washer, M 10 hexagonal screw, M 10 x 65 spring clip, 3,2 mm ball head, squeege support spring washer, M 20 bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 SAUGFUSSAUFHAENGUNG/SQUEEGEE SUPPORT 01 02 03 04 11 08 09 DATUM/DATE: 01/2013 05 17 06 07 13 16 17 20 23 42 14 39 40 41 19 18 12 10 BLATT/PAGE: 14 24 15 25 26 27 22 28 21 29 32 38 33 37 34 36 35 31 30 85587/85590 0038 0039 0040 0041 0042 Titan 351 BF 140 1 2 2 2 1 16705 05269 05116 05219 22906 Sechskantschraube, M 20 x 35 Sechskantschraube, M 10 x 30 Unterlegscheibe, M 10 Mutter, M 10, selbstsichernd Saugfussaufnahme hexagonal screw, M 20 x 35 hexagonal screw, M 10 x 30 washer, M 10 self-locking nut, M 10 squeegee support Blatt/Page 18 SF.Aufhängung-Squeegee Support 85587/85590 MODELL/MODEL: TITAN 351 BF 140 WASSERLEITSYSTEM/WATER GUIDING SYSTEM 06 01 07 08 09 10 11 12 04 02 01 13 03 15 44 45 17 43 29 01 27 20 16 01 14 01 30 28 01 39 41 01 19 37 36 26 25 42 21 22 23 31 32 18 40 38 BLATT/PAGE: 15 01 05 01 DATUM/DATE: 01/2013 24 01 33 34 35 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037 Menge 15 1 1 1 1 1 1 1 1 1 1 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Wasserleitsystem-Water Guiding Titan 351 BF 140 Artikel-Nr./Part No. 13935 01705 12847 13964 12799 12847 01705 16988 13923 40911 16898 05119 05218 01705 12847 12799 14356 11760 11761 01705 12476 11137 01565 01705 12477 01705 12477 01705 12476 11137 01565 01705 12476 11137 01565 LAFN05830 FTAC00038 Bezeichnung Schlauchschelle Schlauch, 1/2" Schlauchtülle 1/2" Wasserhahn Reduzierstück Schlauchtülle 1/2" Schlauch, 1/2" Magnetventil, 36 V Dichtung für Magnetventil Magnetventilkabel Wasserpumpe, 36 V Unterlegscheibe, M 6 Mutter, M 6, selbstsichernd Schlauch, 1/2" Schlauchtülle 1/2" Reduzierstück Winkel 90 Grad Gardena Hahnstück Gardena Schlauchstück Schlauch, 1/2" Winkeleinschraubstutzen Unterlegscheibe, M 20 Gegenmutter, Messing, 1/2" Schlauch, 1/2" T-Stück Schlauch, 1/2" T-Stück Schlauch, 1/2" Winkeleinschraubstutzen Unterlegscheibe, M 20 Gegenmutter, Messing, 1/2" Schlauch, 1/2" Winkeleinschraubstutzen Unterlegscheibe, M 20 Gegenmutter, Messing, 1/2" Filtereinsatz Wasserfilter Description hose clamp hose, 1/2" hose liner, 1/2" stopcock reducing piece hose liner, 1/2" hose, 1/2" solenoid valve, 36 V sealing for solenoid valve solenoid valve cable water pump, 36 V washer, M 6 self-locking nut, M 6 hose, 1/2" hose liner, 1/2" reducing piece elbow, 90 degree Gardena threaded Gardena coupling hose, 1/2" elbow, 90 degree washer, M 20 lock nut, 1/2" hose, 1/2" T-fitting hose, 1/2" T-fitting hose, 1/2" elbow, 90 degree washer, M 20 lock nut, 1/2" hose, 1/2" elbow, 90 degree washer, M 20 lock nut, 1/2" filter element water filter Blatt/Page 19 bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 WASSERLEITSYSTEM/WATER GUIDING SYSTEM 06 01 07 08 09 10 11 12 04 02 01 13 03 15 44 45 17 43 29 01 27 20 16 01 14 01 30 28 01 39 41 01 19 37 36 26 25 42 21 22 23 31 32 18 40 38 BLATT/PAGE: 15 01 05 01 DATUM/DATE: 01/2013 24 01 33 34 35 85587/85590 0038 0039 0040 0041 0042 0043 0044 0045 Titan 351 BF 140 1 4 2 2 2 1 2 2 75105 05119 05119 05218 05359 22903 05119 05218 Sechskantschraube, M 6 x 60 Unterlegscheibe, M 6 Unterlegscheibe, M 6 Mutter, M 6, selbstsichernd Kappe für Sechskantmutter, M 6 Halter für Wasserfilter Unterlegscheibe, M 6 Mutter, M 6, selbstsichernd hexagonal screw, M 6 x 60 washer, M 6 washer, M 6 self-locking nut, M 6 cap for hexagonal nut, M 6 support for water filter washer, M 6 self-locking nut, M 6 Blatt/Page 20 Wasserleitsystem-Water Guiding 85587/85590 MODELL/MODEL: TITAN 351 BF 140 VERDRAHTUNGSPLATTE/WIRING PLATE DATUM/DATE: 01/2013 BLATT/PAGE: 16 14 13 11 12 14 15 10 08 16 15 19 07 18 20 06 17 09 21 21 22 02 05 01 03 38 37 04 36 35 34 39 40 28 33 32 31 30 29 27 26 25 24 23 41 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037 Menge 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 7 Verdrahtungsplatte-Wiring Plate Titan 351 BF 140 Artikel-Nr./Part No. 22904 06234 06233 16987 22928 16899 13194 06965 13194 14247 14254 16995 16900 05189 13442 16397 16397 16378 22462 06235 12126 12417 13105 16991 16992 16991 16991 16991 06882 06883 06882 06882 06883 06882 06882 06619 13840 Bezeichnung Verdrahtungsplatte Kabelkanal Kabelkanal Hauptschütz, 36 V Aluplatte Steuerung, SEM Relaisgehäuse Blinkrelais Relaisgehäuse Relais, 24 V Schaumabschaltungsplatine Relaisplatine ACX Steuerung Blindniete, 3 x 12 mm Kappe,Buchsen-, Anschlußkabel, Programmierkonsole Anschlußkabel, Programmierkonsole DC/DC wandler Abstandshülse Hutschiene Sicherungshalter Sicherung, 160 A Abschlussplatte Sicherungsautomat, 25 A Sicherungsautomat, 40 A Sicherungsautomat, 25 A Sicherungsautomat, 25 A Sicherungsautomat, 25 A Sicherung, 5 A Sicherung, 7,5 A Sicherung, 5 A Sicherung, 5 A Sicherung, 7,5 A Sicherung, 5 A Sicherung, 5 A Endklammer Sicherungsklemme Blatt/Page 21 Description wiring plate cable duct cable duct main contactor, 36 V aluminium plate SEM control relay socket indicator relay relay socket relay, 24 V foam control PCB relay PCB ACX control rivet, 3 x 12 mm cover for diagnostic cable diagnostic cable diagnostic cable DC/DC converter spacer din rail fuse support fuse, 160 A end plate circuit breaker, 25 A circuit breaker, 40 A circuit breaker, 25 A circuit breaker, 25 A circuit breaker, 25 A fuse, 5 A fuse, 7,5 A fuse, 5 A fuse, 5 A fuse, 7,5 A fuse, 5 A fuse, 5 A limiter for line-up terminal fuse clamp bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 VERDRAHTUNGSPLATTE/WIRING PLATE DATUM/DATE: 01/2013 BLATT/PAGE: 16 14 13 11 12 14 15 10 08 16 15 19 07 18 20 06 17 09 21 21 22 02 05 01 03 38 37 04 36 35 34 39 40 28 33 32 31 30 29 27 26 25 24 23 41 85587/85590 0038 0039 0040 0041 1 20 18 2 Titan 351 BF 140 13841 13104 06615 06356 Abschlussplatte Durchgangsklemme, 4 mm² Durchgangsklemme, 2,5 mm² Kabeldurchführung end plate line-up terminal, 4 mm2 line-up terminal, 2,5 mm2 grommet Blatt/Page 22 Verdrahtungsplatte-Wiring Plate 85587/85590 MODELL/MODEL: TITAN 351 BF 140 FAHRPULT/SWITCH BOARD DATUM/DATE: 01/2013 BLATT/PAGE: 17 13 0 1 10 09 16 11 14 15 17 08 18 07 03 01 04 06 05 02 03 12 24 0 1 19 20 20 21 21 22 22 23 23 04 03 04 85587/85590 Position 0001 0002 0003 0004 0005 0006 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 Menge 2 1 10 10 8 1 1 1 1 2 1 1 1 1 1 2 1 1 1 1 1 2 1 2 1 Fahrpult-Switch Board Titan 351 BF 140 Artikel-Nr./Part No. 05502 03998 05443 05501 12307 60110 30614 70150 30620 11505 30617 14406 70177 16043 06154 11738 AZMC00023 MECI00504 MECI00505 16443 16443 06345 16443 MECI00505 16443 Bezeichnung Blintniete, 4 x 16 mm Abdeckung, Lenksäule Linsensenkkopfschraube, M 6 x 30 Schraubenrosette, M 5 Lamellenstopfen Fronthaube, rot Fronthaube, grün Gummiprofil Platte, Steuerpult Spanplattenschraube, M 3 x 12 Pultaufkleber Batterieentladeanzeiger, 36 V Schalter, vorwärts/rückwärts Drehknopf, Poti Poti, 22 Kohm Meldeleuchte, rot Schlüssel für Schlüsselschalter Schlüsselschalter, Oberteil Schaltelement Schalter, Oberteil Schalter, Oberteil Lamenbirne Schalter, Oberteil Schaltelement Schalter, Oberteil Blatt/Page 23 Description rivet, 4 x 16 mm cover, steering column raised countersunk headscrew, M 6 x 30 collar, M 5 dummy plug front bonnet, red front bonnet, green rubber gasket plate for switch board wood plate screw, M 3 x 12 switch board sticker battery control unit, 36 V direction switch rotary knob, poti poti, 22 Kohm red warning light key for key switch key switch, upper part switch switch, upper part switch, upper part light bulb switch, upper part switch switch, upper part bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 04 02 NOT-AUS/EMERGENCY STOP 05 DATUM/DATE: 01/2013 14 03 12 13 16 06 01 11 10 09 08 15 07 17 18 BLATT/PAGE: 18 85587/85590 Position 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 Menge 1 2 2 2 2 1 2 2 2 2 2 1 1 1 1 1 2 1 Titan 351 BF 140 Artikel-Nr./Part No. 22947 05217 05117 05117 05272 12237 05272 05117 16919 05117 05217 05220 05118 05118 05014 22948 05336 22949 Bezeichnung Entriegelungshebel Gegenstück Mutter, M 5, selbstsichernd Unterlegscheibe, M 5 Unterlegscheibe, M 5 Sechskantschraube, M 5 x 30 Handgriff für Batteriestecker Sechskantschraube, M 5 x 30 Unterlegscheibe, M 5 Stecker, Flach-, 350 A, orange Unterlegscheibe, M 5 Mutter, M 5, selbstsichernd Mutter, M 8, selbstsichernd Unterlegscheibe, M 8 Unterlegscheibe, M 8 Sechskantschraube, M 8 x 30 Anschlag für Entriegelungshebel Senkkopfschraube, M 8 x 25 Hebel, Entriegelungs-, Description release lever counter part self-locking nut, M 5 washer, M 5 washer, M 5 hexagonal screw, M 5 x 30 handle for batterie plug hexagonal screw, M 5 x 30 washer, M 5 Plug, flat, 350 A, orange washer, M 5 self-locking nut, M 5 self-locking nut, M 8 washer, M 8 washer, M 8 hexagonal screw, M 8 x 30 stop for release lever countersunk headscrew, M 8 x 25 release lever Blatt/Page 24 Not Aus-Emergency Stop bis / up to ab / from 85587/85590 MODELL/MODEL: TITAN 351 BF 140 SONDERAUSSTATTUNG/SPEZIAL EQUIPMENT 02 03 DATUM/DATE: 01/2013 BLATT/PAGE: 19 01 06 04 05 07 19 23 08 20 09 21 10 22 18 11 12 24 25 13 14 17 16 15 85587/85590 Position 0001 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 Menge Artikel-Nr./Part No. 1 41952 1 41953 2 05014 2 05118 2 05118 2 05220 1 41956 4 05004 4 05118 4 05118 4 05220 1 22944 1 22944 4 05558 8 05004 8 05118 16 05220 8 05363 1 22945 4 05004 4 05118 4 05118 4 05220 1 30620 1 16993 1 16994 Titan 351 BF 140 Bezeichnung Rundumleuchte, für Maschinen ohne Dach Rundumleuchte, für Maschinen mit Dach Sechskantschraube, M 8 x 30 Unterlegscheibe, M 8 Unterlegscheibe, M 8 Mutter, M 8, selbstsichernd Fahrerschutzdach Sechskantschraube, M 8 x 40 Unterlegscheibe, M 8 Unterlegscheibe, M 8 Mutter, M 8, selbstsichernd Dachstütze, vorne Dachstütze, vorne Senkkopfschraube, M 12 x 20 Sechskantschraube, M 8 x 40 Unterlegscheibe, M 8 Mutter, M 8, selbstsichernd Kappe für Sechskantmutter, M 8 Dachstütze, hinten Sechskantschraube, M 8 x 40 Unterlegscheibe, M 8 Unterlegscheibe, M 8 Mutter, M 8, selbstsichernd Platte, Steuerpult Schalter, Ein/Aus, Chemiedosierung Lamenbirne Blatt/Page 25 Sonderausst.-Special Equipment Description beacon light for machines without shelter beacon light for machines with shelter hexagonal screw, M 8 x 30 washer, M 8 washer, M 8 self-locking nut, M 8 shelter hexagonal screw, M 8 x 40 washer, M 8 washer, M 8 self-locking nut, M 8 front shelter support front shelter support countersunk headscrew, M 12 x 20 hexagonal screw, M 8 x 40 washer, M 8 self-locking nut, M 8 cap for hexagonal nut, M 8 rear shelter support hexagonal screw, M 8 x 40 washer, M 8 washer, M 8 self-locking nut, M 8 plate for switch board switch, on/off, chemdose system light bulb bis / up to ab / from IP Gansow GmbH Dreherstraße 9 D 59425 Unna www.gansow.de March 2013