Download Sony CDX-GT317EE, CDX-GT360
Transcript
CDX-GT317EE/GT360 SERVICE MANUAL Saudi Arabia Model CDX-GT360 East European Model Ver. 1.1 2007.03 CDX-GT317EE (Photo: CDX-GT317EE) • The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CDX-GT262/GT217 CD Drive Mechanism Type MG-101TA-188//Q Optical Pick-up Name DAX-25A SPECIFICATIONS CD player section Signal-to-noise ratio Frequency response Wow and flutter MW/LW (GT317EE) Tuning range MW: 531 – 1,602 kHz LW: 153 – 279 kHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 µV, LW: 40 µV 120 dB 10 – 20,000 Hz Below measurable limit Tuner section FM Tuning range MW/SW (GT360) Tuning range GT317EE: FM1/FM2: 87.5 – 108.0 MHz (at 50 kHz step) FM3: 65 – 74 MHz (at 30 kHz step) GT360: 87.5 – 108.0 MHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz MW: 531 – 1,602 kHz SW1: 2,940 – 7,735 kHz SW2: 9,500 – 18,135 kHz (except for 10,140 – 11,575 kHz) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output GT317EE: 50 W × 4 (at 4 ohms) GT360: 52 W × 4 (at 4 ohms) – Continued on next page – FM/MW/LW COMPACT DISC PLAYER CDX-GT317EE FM/MW/SW COMPACT DISC PLAYER CDX-GT360 9-887-460-02 2007C04-1 © 2007.03 Sony Corporation eVehicle Division Published by Sony Techno Create Corporation CDX-GT317EE/GT360 General Outputs Inputs Tone controls Power requirements Dimensions Mounting dimensions Mass Supplied accessories Audio outputs terminal (sub/rear switchable) Power antenna relay control terminal Power amplifier control terminal Telephone ATT control terminal (GT317EE) BUS control input terminal BUS audio input terminal Antenna input terminal AUX input jack (stereo mini jack) Low: ±10 dB at 60 Hz (XPLOD) Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz (XPLOD) 12 V DC car battery (negative ground) Approx. 178 × 50 × 179 mm (7 1/8 × 2 × 7 1/8 in.) (w/h/d) Approx. 182 × 53 × 162 mm (7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d) Approx. 1.2 kg (2 lb. 11 oz.) Card remote commander: RM-X151 Parts for installation and connections (1 set) Design and specifications are subject to change without notice. Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. TEST DISCS Please use the following test discs for the check on the CD section. YDES-18 (Part No. 3-702-101-01) PATD-012 (Part No. 4-225-203-01) CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pickup block. optical pick-up SERVICE NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. semi-fixed resistor SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 2 CDX-GT317EE/GT360 This compact disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the exterior. • CD playback You can play CD-DA (also containing CD TEXT*), CD-R/CDRW (MP3/WMA files also containing Multi Session . Type of discs Label on the disc CD-DA This label is located on the bottom of the chassis. MP3 WMA * A CD TEXT disc is a CD-DA that includes information such as disc, artist and track name. SOLDER • UNLEADED Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CN350) and the SERVO board (CN2) with the extension cable (Part No. J-2502-076-1). MAIN BOARD CN350 Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. J-2502-076-1 SERVO BOARD CN2 3 CDX-GT317EE/GT360 Ver. 1.1 NOTE FOR REPLACEMENT OF THE SERVO BOARD When repairing, the complete SERVO board (A-1177-201-A) should be replaced since any parts in the SERVO board cannot be repaired. TABLE OF CONTENTS 1. GENERAL Location of Controls ........................................................ 5 Connections ..................................................................... 6 NOTE FOR REPLACEMENT OF THE AUX JACK (J901) To replace the AUX jack requires alignment. 1. Insert the AUX jack into the KEY board. 2. Place the KEY board on the front panel. 3. Solder the three terminals of the jack. KEY board AUX jack 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. Sub Panel (FL) Assy ........................................................ CD Mechanism Block ..................................................... Main Board ...................................................................... Servo Board ..................................................................... Chassis (T) Sub Assy ....................................................... Roller Arm Assy .............................................................. Chassis (OP) Assy ........................................................... 3. DIAGNOSIS FUNCTION ........................................ 15 4. DIAGRAMS 4-1. 4-2. 4-3. 4-4. 4-5. 4-6. 4-7. 4-8. Block Diagram –Main Section– ...................................... Block Diagram –Display Section– .................................. Printed Wiring Board –Main Section– ............................ Schematic Diagram –Main Section (1/3)– ...................... Schematic Diagram –Main Section (2/3)– ...................... Schematic Diagram –Main Section (3/3)– ...................... Printed Wiring Board –Key Section– .............................. Schematic Diagram –Key Section– ................................. 5. EXPLODED VIEWS 11 11 12 12 13 13 14 17 18 20 21 22 23 24 25 5-1. Main Section .................................................................... 30 5-2. Front Panel Section ......................................................... 31 5-3. CD Mechanism Section (MG-101TA-188//Q) ................ 32 6. front panel 4 ELECTRICAL PARTS LIST .................................. 33 CDX-GT317EE/GT360 SECTION 1 GENERAL This section is extracted from instruction manual. • LOCATION OF CONTROLS • CDX-GT317EE Location of controls and basic operations Main unit 12 3 4 5 6 7 8 OFF PUSH SELECT EQ3 SOURCE AUX SEEK SEEK L Receptor for the card remote commander MODE PTY DIM ALBM 1 DSPL 2 REP SHUF 3 4 PAUSE 5 6 AF/TA CDX-GT317EE 9q; qa qs qdqfqg qh Card remote commander RM-X151 1 4 qk OFF SOURCE SEL MODE A OFF button To power off; stop the source. B EQ3 (equalizer) button 11 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). + ws wd C Volume control dial/select button 11 To adjust volume (rotate); select setup items (press and rotate). wf D SOURCE button To power on; change the source (Radio/CD/ MD*1/AUX). – qf SCRL DSPL 1 4 2 3 5 6 E Disc slot Insert the disc (label side up), playback starts. + ql qj Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit. w; wa qd ATT VOL – K SEEK –/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold). M MODE button 8, 12 To select the radio band (FM/MW/LW); select the unit*2. N DSPL (display)/DIM (dimmer) button 8, 9 To change display items (press); change the display brightness (press and hold). The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4). qk < (.)/, (>) buttons To control CD/radio, the same as (SEEK) –/+ on the unit. ql VOL (volume) +/– button To adjust volume. w; ATT (attenuate) button To attenuate the sound. To cancel, press again. wa SEL (select) button The same as the select button on the unit. ws M (+)/m (–) buttons To control CD, the same as (1)/(2) (ALBM –/+) on the unit. O RESET button (located behind the front panel) 4 wd SCRL (scroll) button 8 To scroll the display item. P Number buttons CD/MD*1: (1)/(2): ALBM –/+*3*4 To skip albums (press); skip albums continuously (press and hold). (3): REP 8 (4): SHUF 8 (6): PAUSE*5 To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold). wf Number buttons To receive stored stations (press); store stations (press and hold). Q AF (Alternative Frequencies)/TA (Traffic Announcement) button 9 To set AF and TA in RDS. When an MD changer is connected. When a CD/MD changer is connected. When an MP3/WMA is played. If the changer is connected, the operation is different, see page 13. *5 When playing back on this unit. *1 *2 *3 *4 Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip For details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 15. F Display window G AUX input jack 12 To connect a portable audio device. H Z (eject) button To eject the disc. I PTY (Program Type) button 10 To select PTY in RDS. J (front panel release) button 5 6 7 • CDX-GT360 Location of controls and basic operations Main unit 12 3 4 5 6 7 8 OFF PUSH SELECT EQ3 SOURCE AUX SEEK SEEK BTM L Receptor for the card remote commander MODE DIM ALBM 1 DSPL 2 REP SHUF 3 4 PAUSE 5 6 SCRL CDX-GT360 9q; qa qs qdqfqg Card remote commander RM-X151 1 4 qk OFF SOURCE ATT SEL MODE w; wa qd + ws ql SCRL DSPL 1 2 3 4 5 6 + VOL – qh qj Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit. A OFF button To power off; stop the source. B EQ3 (equalizer) button 9 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). qj C Volume control dial/select button 9 To adjust volume (rotate); select setup items (press and rotate). wd D SOURCE button To power on; change the source (Radio/CD/ MD*1/AUX). – qf K SEEK –/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold). E Disc slot Insert the disc (label side up), playback starts. M MODE button 8, 11 To select the radio band (FM/MW/SW); select the unit*2. N DSPL (display)/DIM (dimmer) button 8 To change display items (press); change the display brightness (press and hold). O RESET button (located behind the front panel) 4 P Number buttons CD/MD*1: (1)/(2): ALBM –/+*3*4 To skip albums (press); skip albums continuously (press and hold). (3): REP 8 (4): SHUF 8 (6): PAUSE*5 To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold). Q SCRL (scroll) button 8 To scroll the display item. The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4). qk < (.)/, (>) buttons To control CD/radio, the same as (SEEK) –/+ on the unit. ql VOL (volume) +/– button To adjust volume. w; ATT (attenuate) button To attenuate the sound. To cancel, press again. wa SEL (select) button The same as the select button on the unit. ws M (+)/m (–) buttons To control CD, the same as (1)/(2) (ALBM –/+) on the unit. wd Number buttons To receive stored stations (press); store stations (press and hold). When an MD changer is connected. When a CD/MD changer is connected. When an MP3/WMA is played. If the changer is connected, the operation is different, see page 11. *5 When playing back on this unit. *1 *2 *3 *4 Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip For details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 13. F Display window G AUX input jack 10 To connect a portable audio device. H Z (eject) button To eject the disc. I BTM button 8 To start the BTM function (press and hold). J 6 (front panel release) button 5 7 5 CDX-GT317EE/GT360 • CONNECTIONS • CDX-GT317EE Connection example Notes (2-A) • Be sure to connect the ground (earth) lead before connecting the amplifier. • The alarm will only sound if the built-in amplifier is used. A Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary. AUDIO OUT REAR* * AUDIO OUT SUB/REAR B BUS AUDIO IN BUS CONTROL IN BUS AUDIO IN Source selector* * XA-C40 BUS CONTROL IN * not supplied 6 CDX-GT317EE/GT360 Source selector (not supplied) Supplied with the CD/MD changer XA-C40 Supplied with XA-C40 XA-C40 *2 AUDIO OUT REAR*3 L 2 R *1 from car antenna (aerial) BUS AUDIO OUT IN REAR/SUB Fuse (10 A) BUS AUDIO IN Blue/white striped BUS CONTROL IN 1 3 5 7 2 4 6 8 3 from the car’s speaker connector AMP REM Max. supply current 0.3 A Light blue ATT 1 Purple 2 3 *1 Note for the aerial connecting If your car aerial is an ISO (International Organization for Standardization) type, use the supplied adaptor 2 to connect it. First connect the car antenna (aerial) to the supplied adaptor, then connect it to the antenna (aerial) jack of the master unit. *2 RCA pin cord (not supplied) *3 AUDIO OUT can be switched to SUB or REAR. For details, see the supplied Operating Instructions. + – + Grey 4 – Speaker, Rear, Right Speaker, Rear, Right Speaker, Front, Right Speaker, Front, Right 5 White 6 7 Speaker, Front, Left + Speaker, Front, Left – Green 8 Speaker, Rear, Left + Speaker, Rear, Left – Negative polarity positions 2, 4, 6, and 8 have striped leads. 5 7 from the car’s power connector *1 4 See “Power connection diagram” on the reverse side for details. *2 *3 4 5 Yellow continuous power supply Blue power antenna (aerial) control 7 8 8 Red switched power supply Black ground (earth) Positions 1, 2, 3, and 6 do not have pins. Connection diagram A To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. B To the interface cable of a car telephone Warning If you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power connecting lead 3 may damage the antenna (aerial). Notes on the control and power suppy leads • The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner, or when you activate the AF (Alternative Frequency) or TA (Traffic Announcement) function. • When your car has built-in FM/MW/LW antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. • A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. 7 CDX-GT317EE/GT360 • CONNECTIONS • CDX-GT360 Connection example Notes (2-A) • Be sure to connect the ground (earth) lead before connecting the amplifier. • The alarm will only sound if the built-in amplifier is used. A Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary. AUDIO OUT REAR* * AUDIO OUT SUB/REAR B BUS AUDIO IN BUS CONTROL IN BUS AUDIO IN Source selector* XA-C40 BUS CONTROL IN * not supplied 8 CDX-GT317EE/GT360 Source selector (not supplied) Supplied with the CD/MD changer Supplied with XA-C40 XA-C40 *1 BUS AUDIO IN L R BUS AUDIO OUT IN REAR/SUB from car antenna (aerial) AUDIO OUT REAR*2 Fuse (10 A) BUS CONTROL IN *1 RCA pin cord (not supplied) *2 AUDIO OUT can be switched SUB or REAR. For details, see the Operating Instructions. Blue/white striped 2 3 AMP REM Max. supply current 0.3 A White Black Left 1 White/black striped Gray Blue Right ANT REM Gray/black striped Green Max. supply current 0.1 A Red Left 4 Green/black striped Purple Right Purple/black striped 2 Yellow 5 Connection diagram 1 To a metal surface of the car First connect the black ground (earth) lead, then connect the yellow, and red power input leads. 2 To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster amplifier Notes • It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). • When your car has a built-in FM/MW/SWantenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” 3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. 4 To the +12 V power terminal which is energized in the accessory position of the ignition key switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. • When your car has a built-in FM/MW/SW antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” 5 To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first. Notes on the control and power supply leads • The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/MW/SW antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. • A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. 9 CDX-GT317EE/GT360 Ver. 1.1 SECTION 2 DISASSEMBLY Note: This set can be disassemble according to the following sequence. SET 2-1. SUB PANEL (FL) ASSY (Page 11) 2-2. CD MECHANISM BLOCK (Page 11) 2-3. MAIN BOARD (Page 12) 2-4. SERVO BOARD (Page 12) 2-5. CHASSIS (T) SUB ASSY (Page 13) 2-6. ROLLER ARM ASSY (Page 13) 2-7. CHASSIS (OP) ASSY (Page 14) 1. CHUCKING ARM SUB ASSY (SUPPLEMENT-1 Page 1) 2. SLED MOTOR ASSY (SUPPLEMENT-1 Page 2) 3. OPTICAL PICK-UP SECTION (SUPPLEMENT-1 Page 3) 4. OPTICAL PICK-UP (SUPPLEMENT-1 Page 3) 10 CDX-GT317EE/GT360 Note: Follow the disassembly procedure in the numerical order given. 2-1. SUB PANEL (FL) ASSY 3 two claws 2 two claws 1 two screws (+PTT 2.6 × 6) 4 sub panel (FL) assy 2-2. CD MECHANISM BLOCK 7 CD mechanism block 6 bracket (CD) 5 two screws (+PTT 2.6 × 4) 3 2 screw (+PTT 2.6 × 6) 4 CN350 1 screw (+PTT 2.6 × 6) 11 CDX-GT317EE/GT360 2-3. MAIN BOARD 2 two screws (+PTT 2.6 × 8) 5 screw (+PTT 2.6 × 10) 4 two screws (+P 2.6 × 8) 6 two screws (+PTT 2.6 × 10) 1 three screws (+BTT 2.6 × 5) 7 screw (+P 2.6 × 10) 8 screw (+PTT 2.6 × 10) 9 heat sink 0 MAIN board 3 insulating sheet 2-4. SERVO BOARD WHT RED BLK WHT RED BLK RED ORG BLE YEL GRY 2 toothed lock screw (M 1.7 × 2.5) 3 toothed lock screw (M 1.7 × 2.5) SERVO board 5 SERVO board 1 Remove the eleven solders. 4 optical pick-up (16 core) (CN1) claw claw 12 CDX-GT317EE/GT360 2-5. CHASSIS (T) SUB ASSY 2 two precision screws (+P 1.7 × 2.2) 1 two precision screws (+P 1.7 × 2.2) 4 chassis (T) sub assy 3 claw 2-6. ROLLER ARM ASSY 5 roller arm assy 4 gear (RA1) 1 spring (RAL) 3 washer 2 spring (RAR) 13 CDX-GT317EE/GT360 Ver. 1.1 2-7. CHASSIS (OP) ASSY 6 chassis (OP) assy 1 tension spring (KF) 5 7 coil spring (damper) (natural) 8 coil spring (damper) (green) 4 slider (R) 3 lever (D) 2 gear (LE1) 14 CDX-GT317EE/GT360 SECTION 3 DIAGNOSIS FUNCTION Description of the Diagnostics function: 4. Contents of each display mode 4-1. Reset count display mode 1. Setting the Diag display mode With the power off, press the [4] button, [5] button, and [4] button on the set body or the remote control (for more than 2 seconds) in turn. 2. Canceling the Diag display mode During the Diag function mode, press the [OFF] button. 3. Initial display in the Diag display mode. Just when the Diag mode is entered, “reset count” is displayed. The display mode is switched by each rotation of SEEK +/M > or SEEK – /. m keys. XX Reset count (in hexadecimal format) Diag code 01: Reset count 4-2. Reset count by watchdog timer display mode 02 XX Reset count (in hexadecimal format) Reset count display 01 01 Diag code 02: Number of resets by watchdog timer XX 4-3. Number of connected units display mode Reset count by watchdog timer display 02 XX Number of connected units display 031 XXX 031 XXX Show the number of connected units for CD-C, MD-C and XM respectively from the rightmost (in hexadecimal format). Recency of information 1-3: 1 represents the latest. Diag code 03: Number of connected unit. Operating hours display 04 XXXX The display mode is switched by each rotation of [2/ALBM+] or [1/ALBM--] keys during the number of connected units display mode. CD error information display 051 No. of connected units history 1 (latest) display XX 031 OFFSET/FAILURE error display XXX No. of connected units history 2 display 061XXXXX 032 XXX No. of connected units history 3 display 033 XXX 4-4. Operating hours display mode 04 XXXX Operating hours (in hexadecimal format) Diag code 04: Operating hours 15 CDX-GT317EE/GT360 4-5. CD error information display mode 4-5-1. Error description 4-6. OFFSET/FAILURE error display mode 061XXXXX 051 XX Error information Error description Indication Description (in hexadecimal 1X SERVO ERROR format) 3X LOADING ERROR Recency of information 4X TRACK JUMP 1-3: 1 represents the latest. 5X TEXT ERROR Diag code FX MECHA ERROR 05: CD error information Operating hours Error description (0: OFFSET, 1: FAILURE) Recency of information 1-3: 1 represents the latest. Diag code 06: OFFSET/FAILURE The display mode is switched by each rotation of [2/ALBM+] or [1/ALBM--] keys during the OFFSET/FAILURE error display mode. 4-5-2. Disc type and operating hours 051XXXXX OFFSET/FAILURE error history 1 (latest) display Disc type Operating hours Disc type Recency of information 1-3: 1 represents the latest. Diag code 05: CD error information Indication 0 1 2 3 8 F Disc type MP3 WMA AAC ATRAC CD/DA UNKNOWN The display mode is switched by each rotation of [2/ALBM+] or [1/ALBM--] keys during the CD error information display mode. 061XXXXX OFFSET/FAILURE error history 2 display 062XXXXX OFFSET/FAILURE error history 3 display 063XXXXX CD error info history 1 (latest) Error description plus error details display 051 XX CD error info history 1 (latest) Disc type plus operating hours display 051XXXXX CD error info history 2 Error description plus error details display 052 XX CD error info history 2 Disc type plus operating hours display 052XXXXX CD error info history 3 Error description plus error details display 053 XX CD error info history 3 Disc type plus operating hours display 053XXXXX 16 CDX-GT317EE/GT360 SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM — MAIN SECTION — J652 (1/2) ELECTRONIC VOLUME IC401 L BUS AUDIO IN R J652 (2/2) BUS-RCH CD L CD R CD-RCH 6 CD-LCH 5 CD-RCH AUX-RCH 9 AUX-LCH 7 AUX-RCH CD-RCH CDON CDMON ZMUTE CD ON CDM ON Z MUTE TU-RCH 4 TU-LCH 3 TU-RCH B/U CHECK B/U CHECK I2C BUS CONTROLLED POWER AMP/ MULTIPLE VOLTAGE REGULATOR IC300 OUT-RL 23 11 IN RL R-CH(FRONT) R-CH(REAR) MUTE Q440 DR+6V MECHA+6V BU+3.3V SCL SDA MUTE CONTROL SWITCH Q491,492 2 A ATT D491 4 FR+ 12 FR– 3 RR+ 11 RR– R-CH BATT 5 AMP-REM 6 ANT-REM D493 F901 16 VP 35 SERVO+3.3V D+3.3V SYSTEM CONTROL IC501 (1/2) AUX R-CH CDMON CDON ZMUTE AUX 92 CDMON 91 CDON 61 Z MUTE TU1 (TUNER UNIT) I2C SCK 33 I2C SIO 34 2 SDA 4 SCL SCL SDA 16 BEEP 22 STB 25 DIAG ATT 100 BATT BATT SDA SCL VOLATT 9 RL+ RL– 10 AMP REM 29 ANT REM 27 BU+3.3V A+3.3V CN300 1 FL+ 9 FL– OUT FL+ 5 OUT FL– 3 OUT RL+ 9 OUT RL– 7 MUTE Q470 UNICLK UNI CLK J901 12 IN FL SCL 29 SDA 30 LINKOFF UNISO UNISI LINK OFF UNI SO UNI SI MUTE Q432 AUDIO OUT REAR R R-CH MUTE 28 BUSON BUS ON R-CH OUT-FR 26 OUT-RR 24 A ATT A ATT L SUBOUT-L 21 SUBOUT-R 22 OUT-FL 25 SYSRST SYS RST CD MECHANISM UNIT (MG-101TA) BUS-RCH 2 BUS-LCH 1 BUS-RCH AUDIO+B BU+B SERVO3.3V MECHA6V PANEL+B 30 37 31 33 34 AUDIO+8.3V BU+5V SERVO+3.3V MECHA+6V PANEL+B BEEP 5 L-CH 4 1 ANT R-CH 3 TUNER+5V REG Q3 E2PVDD 15 BU+3.3V ACCIN 99 GT317EE AUDIO+8.3V BU+5V 39 VSM 12 TUATT E2P SCL 16 E2P SDA 17 25 EEP CKO 24 EEP SIO 96 60 54 58 UNISO 59 12 11 10 8 9 BUSON UNISCK BUIN UNISI BUS IN CLK IN B/U-C DATA OUT DATA IN 13 NSMASK SYSRST 88 TEST TH400 D602 BATT BATT 7 BUS ON 1 38 QUALITY 53 TU ATTIN 4 5 6 BUS ON SWITCH Q601 1 2 3 CNJ400 BUS CONTROL IN 8 RST 2 SYSRST RDS DEMODULATOR IC50 SCL SDA LINK OFF SWITCH Q600 LINKOFF • R-CH is omitted due to same as L-CH. • Signal Path : CD PLAY : FM 16 MPX INTN 15 9 XTI BATTERY CHECK Q605 CLK 4 DATA I/O 6 13 RST D353 QUALITY 5 MUTE CON 8 SCL 11 SDA 12 BATT 3 D609 NOISE MASK SWITCH Q1 10 XTO TEL ATT 15 BUS INTERFACE IC601 S-METER 6 TU MUTE 7 X50 8.664MHz ACC 13 TESTIN 97 SCL SDA RDS OUT 9 7 ACCESSORY CHECK Q702 TELEPHONE ATTENATION CHECK Q701 TELATT 98 BU+3.3V REG IC681 UNISI B/U CHECK UNICLK BUSON TU-SCL 13 TU-SDA 14 DIAG 7 AUDIO+8.3V VCC 10 VDD+5V 11 AMPSTB 8 TU-RCH UNISO J1 (ANTENNA) VDDA 1 VDDD 7 56 DAVN RDS+3.3V SWITCH Q50 : MW/LW/SW BU+3.3V RESET A DISPLAY SECTION (Page 18) 26 RDS ON GT317EE CDX-GT317EE/GT360 17 17 : AUX CDX-GT317EE/GT360 4-2. BLOCK DIAGRAM — DISPLAY SECTION — FL901 FLUORESCENT INDICATOR TUBE SYSTEM CONTROL IC501 (2/2) GRID1 20 41 KEYIN0 KEY MATRIX LSW901,902 S901–904,906–915 40 KEYIN1 D503 KEY ACKNOWLEDGE SWITCH Q664 RE901 PUSH SELECT (VOLUME) ROTARY ENCODER GRID2 19 FL SO 28 FL SCK 29 FL CS 27 14 DIO 12 CLK 10 CS GRID3 16 52 KEYACK 17 3G • 18 48 AD ON 6 2G • 42 31 RE-IN0 32 RE-IN1 1G 41 FL DRIVE Q883 FL DRIVE Q882 FL DRIVE Q881 RESET 15 PANEL+B VH 9 FL VH+12V VDD+3.3V REG IC972 VDD(+3.3V) 5 62 NOSESW FL VH+12V PANEL+B PANEL+B REMOTE CONTROL SIGNAL RECEIVER IC971 64 SIRCS XOUT 80 XIN 79 MAIN SECTION OSCOUT 83 A RESET OSCIN 82 (Page 17) FL+3V REG IC202 1 F+ • 2 X502 32.768kHz D204-206 FL+7V REG IC201 D200-203 FL+12V REG IC200 D207 BATT 44 F– • 45 X501 18.432MHz FL VH+12V FL+12V REG IC203 BU+3.3V FL ON 87 RESET IC602 77 RESET PANEL+B GT317EE GT360 S103 RESET LED841–847, 850–857, 861–864 CDX-GT317EE/GT360 18 18 LED941–947, 950–957, 961–963 LSW901,902 CDX-GT317EE/GT360 • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS — MAIN Board — THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) 1 For schematic diagrams. For printed wiring boards. Note: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : internal component. • C : panel designation. Note: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. a : Through hole. • : Pattern from the side which enables seeing. • (The other layers' patterns are not indicated.) Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • • • • • • • • A : B+ Line. B : B– Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ) : MW/LW/SW < > : CD PLAY ∗ : Impossible to measure Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD PLAY F : FM f : MW/LW/SW L : AUX • Semiconductor Location (MAIN Board) • Waveforms Caution: Pattern face side: (Side B) Parts face side: (Side A) IC501 i; (XOUT) 0.8 Vp-p 32.768 kHz 0.2 V/DIV, 20 µsec/DIV 2 Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. IC501 is (OSC IN) 0.9 Vp-p C Q 18.432 MHz These are omitted B E 0.5 V/DIV, 0.1 µsec/DIV 3 IC50 9 (XTI) BE C These are omitted 1.1 Vp-p 8.664 MHz ECB 0.5 V/DIV, 0.1 µsec/DIV These are omitted CDX-GT317EE/GT360 19 19 Ref. No. D2 D101 D103 D104 D105 D106 D108 D109 D110 D111 D112 D113 D153 D200 D201 D202 D203 D204 D205 D206 D207 D301 D302 D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D353 D491 D493 D502 D503 D602 D603 D604 Location F-3 I-4 I-3 I-3 I-3 I-3 I-3 I-4 I-4 I-4 I-4 I-4 I-2 H-10 H-10 H-10 I-10 I-9 I-9 I-9 G-10 C-8 D-8 C-9 D-9 C-6 C-6 C-6 C-6 C-7 C-7 C-8 D-7 G-8 E-5 E-6 H-7 I-6 D-10 D-10 E-10 Ref. No. D605 D606 D607 D609 D702 D703 D704 D901 D998 D999 Location D-10 D-10 D-10 F-9 C-8 C-9 C-9 B-10 C-9 B-8 IC50 IC200 IC201 IC202 IC203 IC300 IC401 IC501 IC601 IC602 IC681 H-2 G-11 I-10 I-7 H-9 B-6 D-3 G-6 E-10 G-8 D-6 Q1 Q3 Q50 Q420 Q432 Q440 Q452 Q460 Q470 Q491 Q492 Q600 Q601 Q605 Q664 Q701 Q702 E-2 F-3 H-2 B-4 B-3 B-4 B-3 C-4 C-4 E-6 E-6 E-10 E-10 D-10 I-6 C-9 C-8 CDX-GT317EE/GT360 4-3. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 19 for Semiconductor Location. 2 1 3 4 5 : Uses unleaded solder. 6 7 8 9 10 11 12 13 14 J652 L R C301 C309 IC300 F901 D103 D106 D104 JW4 D110 D112 JW5 JW7 JC25 D113 C154 (CHASSIS) R709 R702 YEL C705 C702 C703 D311 JW105 C405 C417 C412 C418 C419 IC601 JW106 JW95 JC33 JW110 JW108 L405 C415 C409 C315 C316 JW92 JC3 JC2 JW86 R600 JW90 C204 D503 JW88 R561 R205 JC23 R206 D207 IC200 R201 1 IC203 5 D202 D206 D205 1 R210 D201 JW80 JW109 JW68 JW67 C314 R533 1 R200 C206 R208 D203 C202 1 R202 IC201 R203 R204 5 D204 IC202 5 21 R207 S103 J YEL JW64 JW65 JW63 JW62 JW61 R532 R517 JC16 R673 FMB3 C201 JW93 JW89 JC26 D105 Q664 JC41 JW3 C155 C152 R671 D111 JW6 R152 R153 L151 D153 R154 JW2 JW1 I D109 C502 R502 D101 D108 R570 C200 JW94 5 JW111 C151 C153 C514 R529 JC37 D353 R211 JW84 C512 CD MECHANISM UNIT (MG-101TA) R553 R209 D502 JW82 R504 R505 C501 R351 R519 JC17 R672 R522 R521 C513 R503 R155 R151 C313 R674 C519 JC15 JW18 JW17 C60 JW16 JC27 L406 X501 JW22 R520 IC602 3 2 4 1 L501 C507 IC501 JW19 R58 C57 JW8 JW20 L50 JW15 C56 R523 R512 C510 JW83 R558 Q50 R510 JW21 JW14 C55 C61 H L3 IC50 X50 JW13 C54 R57 R54 L5 R53 JC13 R524 JC28 L2 R52 R511 R525 C52 C53 R509 C509 JW12 C50 R560 JW11 JW9 R15 C51 JW10 C58 R557 R556 JC40 C504 G R610 JC36 D609 CN350 GT360 GT317EE JW85 JW25 Q601 JW107 GT317EE JW91 R544 FMB4 R539 GT360 JW28 JW79 R552 R526 JC4 JW26 JW23 R537 JC38 R612 Q600 R401 C402 R550 JC20 R611 R615 R608 R601 JC35 TH400 L410 C401 R538 JW29 JW81 JW30 R602 JC34 R402 JW78 X502 JW113 JW27 GT317EE R55 D307 JW66 JC1 R551 C205 L4 R7 GT360 R507 R549 JC24 R6 R573 R302 R616 D604 C601 L402 R603 D602 R607 R568 L409 R604 Q605 R606 JC19 JW77 R567 C8 C319 JW100 R555 L401 R540 JW31 JW112 R534 C7 R565 C5 D606 L407 L403 JW76 GT317EE D603 JW96 JC18 GT360 L300 JW103 C403 C318 JW32 BATT D304 R636 JW75 JC14 R13 D303 D301 D702 JW74 C363 JC12 JW24 D2 C704 D605 JW73 R301 JW34 JC21 Q702 R708 R707 JW98 R563 JW72 JW35 D703 C701 JW71 GT360 R566 JW33 C600 D607 GT317EE R564 JW70 Q492 R531 D493 C317 JW37 F JW69 D491 Q3 C6 JW102 JW87 JW44 Q491 JW36 R12 C682 L901 L1 C2 JW60 JW58 C683 C491 R491 JW42 R10 Q701 JW97 C364 C3 C681 C306 R451 JW45 JC8 4 JW99 JC32 JW43 JW41 R9 JW40 JW39 JC5 R5 D310 C508 C431 Q1 GT317EE R8 JW57 C308 C471 R471 R431 R3 R2 R706 IC681 JW46 C451 C1 R430 JC42 R485 R4 JW56 R481 IC401 C461 JW38 C15 R452 R1 E R440 R470 R703 R705 R461 GT317EE D998 D302 C622 R420 R460 5 JW101 D312 JW47 6 C997 L902 C365 C366 C484 C361 GT360 D306 JC7 C362 TU1 D305 C485 C486 D C623 R355 R356 JW55 JC9 JC6 R704 C312 C473 C472 R472 JW48 1 JC22 GT317EE D704 D309 Q470 C JW54 C463 C454 D308 C462 C320 JW59 Q460 R701 JW53 C302 C303 R462 2 7 JW49 C434 JW52 JC10 3 8 JW104 Q452 Q432 C305 C207 R357 C441 JC11 R358 R447 R448 R421 R442 C432 C421 C414 C307 C452 C998 JW51 C413 ATT C304 JW50 D200 C325 C329 Q440 Q420 CN300 YEL C330 D901 C423 R450 R449 C203 C426 D999 C445 C443 B GT317EE CNJ400 (BUS CONTROL IN) -4 JC30 -3 JC29 -2 JC31 R -1 C444 L C424 J1 (ANTENNA) A AUDIO OUT REAR BUS AUDIO IN CN370 S103 RESET X501 (Page 24) CDX-GT317EE/GT360 20 20 1-871-263- (21) CDX-GT317EE/GT360 4-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 26 for IC Block Diagrams. C303 C302 JC29 C325 C444 JC30 C330 C424 L901 C308 C306 C304 C301 JC31 C309 IC B/D C305 C307 C317 IC300 R302 C319 C318 C434 JC12 R709 C320 C312 C313 C315 JC13 D304 D303 D306 D305 D307 C997 D308 D998 D309 C998 D310 D999 D704 D311 R705 D312 R701 C314 D301 C454 C316 R301 D302 CN300 D702 D703 F901 D607 JC33 C701 R703 R702 C704 L902 JC32 Q701 R704 L300 R491 C705 D491 JC8 JC9 IC602 R707 Q492 Q702 R706 C702 C703 (Page 22) IC681 Q491 D493 R708 JC1 R604 R608 D602 Q600 C600 Q605 R610 C601 R612 CNJ400 JC22 JC21 R611 R616 D901 C329 R531 D603 Q601 TH400 R607 R602 R601 JC36 R606 D605 D604 D606 JC20 R615 IC B/D C683 R600 R603 IC601 D609 (Page 23) CDX-GT317EE/GT360 21 21 C682 C681 C491 C622 C623 CDX-GT317EE/GT360 • Refer to page 19 for Waveforms. 4-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 26 for IC Block Diagrams. J652 J1 C445 C426 C463 C443 C423 C462 C473 C472 C362 C361 C452 Q470 Q460 Q420 Q440 C432 Q452 C413 C414 Q432 TU1 Q1 R3 R1 C15 R2 JC11 R357 JC10 R4 C1 R358 R5 R355 R472 R471 R448 R462 R461 C471 R447 R449 JC6 R442 R421 R451 C441 C461 R9 R8 JC5 C365 C366 R431 C3 Q3 L1 C431 C451 C421 R356 R450 JC7 C2 R10 C7 C5 C6 IC B/D D2 IC401 R13 C486 R12 C8 C485 L4 R6 C484 R7 R420 R481 C58 R440 R460 R15 R470 R452 JC42 (Page 21) C364 IC B/D C363 L5 R55 R430 L5 C50 C51 R485 C52 C53 R53 C55 Q50 L50 R52 R57 R558 L2 R54 C60 R58 C57 X50 C54 IC50 C61 C56 L3 JC28 IC B/D IC B/D IC B/D IC203 IC B/D IC200 D113 IC201 IC202 CN370 JC41 D207 R208 R211 C207 C200 D101 D112 R205 R204 R203 C201 D201 R209 C206 R202 R200 R201 D200 C203 D203 D202 JC25 JC26 R207 D204 D206 D205 C202 R206 R210 D109 D108 D103 C205 C204 D111 D110 D105 D104 D106 D153 C151 (Page 23) CDX-GT317EE/GT360 22 22 R151 C152 R154 C153 R155 R153 L151 C154 R152 C155 (Page 25) CDX-GT317EE/GT360 • Refer to page 19 for Waveforms. 4-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 28 for IC Pin Description of IC501. (Page 22) (Page 21) C509 R553 R529 R672 X502 C508 JC19 R561 R517 JC24 Q664 R570 C507 R568 JC37 R519 R533 JC2 R532 R674 C519 D502 JC17 JC16 CN350 X501 R565 C403 JC34 R555 C412 R509 JC35 L407 L501 C417 L409 L401 C405 L403 L405 R567 L402 R402 C510 R526 C419 D503 C502 L410 C409 C415 R671 R401 C418 R673 JC23 R539 R505 R503 JC3 L406 IC501 R540 JC18 R351 R502 R636 C512 R564 R504 C501 R563 C401 C514 JC15 C513 R522 C402 R521 R520 R523 R524 R560 23 JC4 R510 R512 JC27 C504 R511 R557 CDX-GT317EE/GT360 23 R556 JC14 JC38 R534 R552 R537 R551 R507 R538 R573 R550 R549 JC40 R544 R566 D353 S103 R525 CDX-GT317EE/GT360 4-7. PRINTED WIRING BOARD — KEY SECTION — LED861-864,961-963 (RING ILLUMINATION) R943 10 11 12 R961 13 LED841,941, S901 R942 GT317EE LED842 GT317EE LED841 S901 LED842,942 (CD INDICATOR) R842 GT360 LED942 GT360 S903 GT317EE R962 GT360 LED863 R861 GT317EE 9 LSW901 R947 GT317EE R906 R907 R908 IC971 D S909 S910 LED851,951, S909 1/ALBM– LED852,952, S910 2/ALBM+ S911 GT317EE LED847,947, LED850,950, S908 S907 MODE DSPL/DIM S912 R954 LED957 LED857 GT360 GT317EE GT317EE R853 11 R953 S915 S914 GT317EE 1-871-262- GT360 LED856,956 S914 6/PAUSE LED855,955 S913 5 LED854,954, S912 4/SHUF LED956 LED856 R854 GT360 S913 GT317EE GT317EE LED853,953, S911 3/REP GT317EE GT360 GT360 LED955 LED855 R909 LED954 GT360 GT360 GT360 LED854 S908 2 3 GT360 GT360 GT317EE LED953 GT360 GT317EE S907 LED853 LED864 GT317EE LED952 GT360 LED947 LED847 C974 IC971 R977 1 4 LED852 GT360 LED962 GT360 LED951 LED851 LED963 LED850 GT317EE LED945 LED845 S906 LED845,945, S906 PTY LED862 GT317EE GT360 8 GT360 LED941 GT360 GT317EE LED946 R843 LED944 LED844 LSW902 GT317EE SEEK– C GT360 LED961 GT317EE LED861 R862 LSW902 S904 B LED844,944, S904 EQ3 7 LED846,946, S903 SOURCE LSW901 M> SEEK+ R903 GT360 R904 6 R941 S902 5 LED950 OFF 4 R841 LED843 GT317EE LED843,943, LED943 GT360 S902 R902 A 3 LED846 2 1 : Uses unleaded solder. (11) LED857,957, S915 AF/TA (GT317EE) SCRL (GT360) MAIN BOARD CN370 (Page 20) A CN901 GT317EE 3 GT317EE R881 Q883 D908 R889 R882 FB901 IC972 C976 R978 D906 C982 C981 R883 FB902 D907 R886 D882 R887 38 R885 D903 FB903 D905 R988 4 R884 R983 R971 J901 AUX C975 R989 5 R901 D904 Q881 Q882 R982 R888 R948 C904 GT360 R946 RE901 C992 FB904 R914 R915 FL901 FLUORESCENT INDICATOR TUBE C977 R864 GT317EE F C991 R863 R846 2 GT360 GT317EE R952 R852 R913 R951 R911 R950 R850 R910 R912 GT317EE R845 1 R945 R844 R944 R975 GT360 R922 GT317EE GT360 R905 R949 R849 R976 D971 R921 GT360 GT317EE R851 GT360 E R981 G RE901 PUSH SELECT (VOLUME) 11 1-871-262- • Semiconductor Location Ref. No. Location D882 D903 D904 D905 D906 D907 D908 D971 F-7 F-10 F-9 F-10 F-10 F-10 F-10 E-4 IC971 IC972 C-4 F-10 LED841 LED842 A-12 B-7 CDX-GT317EE/GT360 24 24 Ref. No. LED843 LED844 LED845 LED846 LED847 LED850 LED851 LED852 LED853 LED854 LED855 LED856 LED857 LED861 Location A-1 B-2 C-2 B-4 C-4 C-5 C-6 C-6 C-7 C-8 C-9 C-10 C-11 B-3 Ref. No. LED862 LED863 LED864 LED941 LED942 LED943 LED944 LED945 LED946 LED947 LED950 LED951 LED952 LED953 Location B-2 B-3 C-3 A-12 B-7 A-1 B-2 C-2 B-4 C-4 C-5 C-5 C-6 C-7 Ref. No. LED954 LED955 LED956 LED957 LED961 LED962 LED963 Location C-8 C-9 C-10 C-10 B-3 C-3 C-2 Q881 Q882 Q883 F-8 F-8 F-9 (11) CDX-GT317EE/GT360 4-8. SCHEMATIC DIAGRAM — KEY SECTION — R981 R978 R941 R943 R841 LED946 R843 LED846 R949 R947 R951 R849 R851 R953 LED961 R853 LED861 C976 LED863 C977 R942 LED944 R842 LED844 R945 LSW901(1/2) R845 LED950 LED953 LED850 LED853 LED957 LED857 R961 R861 R982 R863 LED941 LED841 R944 R946 R844 R846 LED951 R948 LED851 R952 R954 R852 LED862 R962 R854 C975 IC972 R864 LED942 LED945 LED842 LED947 LED845 LED847 LSW902(1/2) R950 LED954 R850 LED854 LED956 LED856 LED962 R862 R975 LED864 R976 LED943 LED952 LED843 LED955 LED852 R977 LED963 LED855 IC971 D971 C974 C992 C991 C982 CN901 D908 R886 R922 R901 R971 R902 R903 R921 Q883 RE901 D904 R889 R887 R983 R888 C904 FB904 R905 R904 D882 R988 R884 D903 R882 R907 R908 R909 R910 R911 R912 R913 R914 R915 S908 S909 S910 S911 S912 S913 S914 S915 LSW902(2/2) LSW901(2/2) D907 D906 D905 R906 S907 Q881 (Page 22) C981 Q882 S906 S904 S903 S902 S901 R885 R883 R881 FB903 FB901 FB902 FL901 J901 CDX-GT317EE/GT360 25 25 R989 CDX-GT317EE/GT360 • IC BLOCK DIAGRAMS IC300 TDA8588AJ/N2/R1 (MAIN Board (1/3)) IC601 BA8271F-E2 (MAIN Board (1/3)) TAB 1 2 SDA OUT-FL- 3 BUS ON 1 BUS ON SWITCH RST 2 RESET SWITCH BATT 3 BATTERY SWITCH 14 VCC I2C BUS 4 SCL FL OUT-FL+ 5 6 VP2 OUT-RL- 7 RL MUTE 10 SVR PROTECTION/ DIAGNOSTIC IN-RR 15 CLK 4 VREF 5 DATA 6 9 DATA IN GND 7 8 DATA OUT 12 IN-FL 14 IN-FR MUTE S-GND 13 RESET BUS ON CLK IN BU IN 8 PGND3 OUT-RL+ 9 IN-RL 11 13 12 11 10 16 BEEP VP OUT-RR+ 17 18 PGND2 RR OUT-RR- 19 20 VP1 OUT-FR+ 21 FR OUT-FR- 23 STANDBY/ MUTE 22 STB CHIP DETECT/ DIAGNOSTIC 24 PGND1 BATTERY DETECTION DIAG 25 TEMPERATURE PROTECTION IC200 IC201 IC202 IC203 ENABLE LOGIC 26 RST ANT-REM 27 SWITCH AMP-REM 29 SWITCH NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) NJM2387ADL3 (MAIN Board (2/3)) CURRENT LIMIT 28 CRES REGULATOR 30 AUDIO8.3V SERVO5V 31 MECH6V 33 32 GND OVERVOLTAGE PROTECTION 34 PANEL+B VP 35 REFERENCE VOLTAGE B.UP+B 37 REGULATOR BANDGAP REFERENCE 36 CBU LOADDUMP PROTECTION THERMAL PROTECTION BACK-UP SWITCH CDX-GT317EE/GT360 26 26 1 2 3 4 5 VIN CONTROL VOUT VADJ GND CDX-GT317EE/GT360 IC401 BD3442FS-E2 (MAIN Board (2/3)) BUS-RCH 1 VCC2 32 F2L 100k 31 GND BUS-LCH 2 INPUT SELECTOR 100k TU-RCH 3 INPUT GAIN VOLUME1 /MUTE TREBLE /BASS /MIDDLE VOLUME2 I2C BUS LOGIC 100k TU-LCH 4 30 SDA 29 SCL 28 MUTE 100k CD-RCH 5 VCC 27 VCC 100k CD-LCH 6 FADER 26 OUT-FR 250k FADER 25 OUT-FL 250k FADER 24 OUT-RR FADER 23 OUT-RL 100k EFFECT AUX-RCH 7 AUX-GND 8 AUX-LCH 9 250k DS3-L 10 22 SUBOUT-R DS1-L 11 FADER DS2-L 12 LPF 21 SUBOUT-L EBIAS 13 FADER 20 ADJ DS2-R 14 19 SAOUT SPECTRUM ANALYZER DS1-R 15 18 SADA 17 SACLK DS3-R 16 IC50 TDA7333013TR (MAIN Board (2/3)) 3 INTERPOLATOR BAND PASS FILTER REF2 3 REF1 4 VSS 5 TM 6 VDDD 7 MPX REF3 2 SINC4 FILTER SIGMA DELTA CONVERTER SINC4REG VDDA 1 RAM RDS RDSREG BUFFER INTN DEMODULATOR & & SYNCHRONIZATION CONTROL LOGIC 16 MPX 15 INTN SDAOUT SDAIN 2 TEST LOGIC SCK I C/SPI & INTERFACE SPI PIN MUX'S TESTREG 14 13 12 11 CSN SA_DATAOUT SDA_DATAIN SCL_CLK 2 10 XTO OSCILLATOR 9 XTI RESETN 8 27 CDX-GT317EE/GT360 • IC PIN DESCRIPTION IC501 MB90F045PF-G-9015-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) (CDX-GT360) IC501 MB90F045PF-G-9043-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) (CDX-GT317EE) Pin No. Pin Name I/O Pin Description 1 AREASEL0 I Destination setting pin 0 2 AREASEL1 I Destination setting pin 1 3 AREASEL2 I Destination setting pin 2 4 B-OUT SEL I Black-out with/without discrimination signal input 5 BEEP O Beep signal output 6 NCO O Not used. (Open) 7 DIAG I Status signal input from power amplifier 8 AMPSTB O Standby signal output to power amplifier 9 VOLATT O Electronic volume attenuate control signal output 10 NCO O Not used. (Open) 11 VSS — Ground pin 12 TUATT O Tuner mute control signal output 13 NSMASK O Noise mask signal output 14 ILLUMI SEL I Illumination voltage setting signal input “H”: Black-out 15 COL SEL I Two colors change setting signal input 16 to 22 NCO O Not used. (Open) 23 VCC5 — Power supply pin (+3.3 V) 24 EEP SIO I/O EEPROM bus serial data signal input/output 25 EEP CKO O EEPROM bus serial clock signal output 26 RDS ON O RDS (Radio Data System) on signal output 27 FL CS O Fluorescent indicator tube chip select signal output 28 FL SO O Fluorescent indicator tube serial data signal output 29 FL SCK O Fluorescent indicator tube serial clock signal output 30 NCO O Not used. (Open) 31 RE IN0 I Rotary encoder signal input 0 32 RE IN1 I Rotary encoder signal input 1 33 I2C SCK O I2C bus serial clock signal output 34 I2C SIO I/O I2C bus serial data signal input/output 35 DAVDD — A/D converter power supply pin (+3.3 V) 36 AVRH — A/D converter external reference power supply pin (+3.3 V) 37 DAVSS — Ground pin 38 QUALITY I Noise detect signal input 39 VSM I S-meter voltage detect signal input 40 KEYIN1 I Key signal input 1 41 KEYIN0 I Key signal input 0 42 VSS — 43 RCIN0 I Rotary commander key signal input 44 to 47 NCO O Not used. (open) 48 AD ON O A/D converter power supply control signal output 49 MD0 I Operation mode setting pin (Connect to VDD.) 50 MD1 I Operation mode setting pin (Connect to VDD.) 51 MD2 I Operation mode setting pin (Connect to VSS.) 52 KEYACK I Key acknowledgment detect signal input 53 TUATTIN I Tuner mute zero cross detect signal input 54 BUIN I Back-up power supply detect signal input 55 NCO O Not used. (Open) 28 Tuner on: “L” Ground pin Not used in this set. CDX-GT317EE/GT360 Pin No. Pin Name I/O 56 DAVN I RDS (Radio Data System) data block synchronized detect signal input Pin Description 57 NCO O Not used. (Open) 58 UNISI I SONY bus data signal input 59 UNISO O SONY bus data signal output 60 UNI SCK O SONY bus clock signal output 61 Z MUTE I Mute signal input 62 NOSE SW I Front panel attachment detect signal input Memory mode change signal input “L”: With panel, “H”: Without panel Normally “H”: Single chip mode, after reset 63 FLASH W I 64 SIRCS I Remote control signal input 65 to 70 NCO O Not used. (Open) 71 RC IN1 I Rotary commander shift key signal input 72 to 76 NCO O Not used. (Open) 77 RESET I CPU reset signal input 78 NCO O Not used. (Open) “L”: flash write mode Not used in this set. 79 XIN I Low speed operation clock signal input (32.768 kHz) 80 XOUT O Low speed operation clock signal output (32.768 kHz) 81 VSS1 — Ground pin 82 OSCIN I High speed operation clock signal input (18.432 MHz) 83 OSCOUT O High speed operation clock signal output (18.432 MHz) 84 VCC3 — Power supply pin (+3.3 V) 85 CYRIL SEL I 86 DEMOSEL I DEMO select signal input 87 FL ON O Fluorescent indicator tube power on signal output 88 SYSRST O System reset signal output 89, 90 NCO O Not used. (Open) 91 CDON I CD mechanism servo power supply control request signal input Cyril correspondence discrimination signal input “L”: No correspondence “H”: DEMO on, “L”: DEMO off 92 CDMON I CD mechanism deck power supply control request signal input 93 to 95 NCO O Not used. (Open) 96 BUSON O Bus on signal output 97 TESTIN I Test mode detect signal input 98 TELATT I Telephone attenuate detect signal input 99 ACCIN I Accessory power supply detect signal input 100 ATT O Audio mute control signal output 29 CDX-GT317EE/GT360 SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • • • 5-1. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. -XX and -X mean standardized parts, so they may have some difference from the original one. Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color Accessories are given in the last of this parts list. MAIN SECTION not supplied A MG-101TA-188//Q #2 7 #1 #3 B A #4 #5 F901 #4 4 #3 #6 #4 not supplied 5 not supplied 3 6 #1 TU1 not supplied B 2 #1 not supplied #1 1 Ref. No. Part No. Description 1 2 3 4 5 X-2148-784-1 3-042-244-11 X-2108-670-1 2-050-124-01 A-1206-400-A PANEL (FL) ASSY, SUB SCREW (T) LOCK ASSY (S) SCREW +BTT 2.6X5 MAIN BOARD, COMPLETE (GT317EE) 5 6 7 A-1206-410-A MAIN BOARD, COMPLETE (GT360) 2-021-848-01 SHEET (TU), GROUND 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER) (GT317EE) 1-833-100-11 CORD (WITH CONNECTOR) (POWER) (GT360) 7 30 Remark Ref. No. Part No. Description F901 TU1 TU1 #1 #2 1-532-877-11 A-3220-960-B A-3220-961-B 7-685-792-09 7-685-790-01 FUSE (BLADE TYPE) (AUTO FUSE) 10A TUNER UNIT (TUX-032) (GT360) TUNER UNIT (TUX-032) (GT317EE) SCREW +PTT 2.6X6 (S) SCREW +PTT 2.6X4 (S) #3 #4 #5 #6 7-685-793-09 7-685-794-09 7-685-134-19 7-621-284-40 SCREW +PTT 2.6X8 (S) SCREW +PTT 2.6X10 (S) SCREW +P 2.6X8 TYPE2 NON-SLIT SCREW +P 2.6X10 Remark CDX-GT317EE/GT360 5-2. FRONT PANEL SECTION 57 56 RE901 not supplied 57 58 not supplied (KEY board) FL901 J901 55 not supplied not supplied 52 54 not supplied not supplied 53 51 Ref. No. Part No. Description 51 51 52 52 53 A-1206-402-A A-1206-412-A X-2149-356-1 X-2149-357-1 X-2149-360-1 PANEL COMPLETE ASSY, FRONT (GT317EE) PANEL COMPLETE ASSY, FRONT (GT360) BUTTON ASSY (S) (GT317EE) BUTTON ASSY (S) (GT360) PANEL (SV) ASSY, FRONT (GT317EE) Remark 53 54 X-2149-361-1 PANEL (SV) ASSY, FRONT (GT360) X-2149-353-1 KNOB (VOL) (SV) ASSY Ref. No. Part No. Description 55 56 57 58 FL901 2-693-599-01 2-684-632-01 3-250-543-21 X-2149-228-2 1-519-909-12 SPRING (RELEASE) PANEL (FL), BACK SCREW (+B P-TITE M2) CASE ASSY (for FRONT PANEL) INDICATOR TUBE, FLUORESCENT Remark J901 RE901 1-820-624-11 JACK (SMALL TYPE) (VERTICAL) (AUX) 1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME) 31 CDX-GT317EE/GT360 Ver. 1.1 5-3. CD MECHANISM SECTION (MG-101TA-188//Q) NOTE: Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP. 101 102 not supplied not supplied 103 #7 #7 105 not supplied not supplied not supplied not supplied not supplied 104 not supplied not supplied not supplied not supplied 107 106 106 Ref. No. Part No. Description 101 102 0 103 104 A-1177-168-A A-1177-169-A X-2149-672-1 2-626-869-01 MECHANICAL BLOCK ASSY DAXEV//Q SERVICE ASSY, OP (DAX-25A) SCREW (M2X3), SERRATION 32 Remark Ref. No. 105 106 107 #7 Part No. Description 3-348-998-31 3-352-758-31 A-1177-201-A 7-627-000-08 SCREW (M1.4X2.5), TAPPING, PAN SCREW (M1.7X2.5), TOOTHED LOCK SERVO BOARD, COMPLETE SCREW, PRECISION +P 1.7X2.2 TYPE3 Remark CDX-GT317EE/GT360 SECTION 6 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable Ref. No. Part No. • • • • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. CAPACITORS uF : µF COILS uH : µH Description Remark KEY BOARD ********** < CAPACITOR > C904 C974 C975 C976 C977 1-165-176-11 1-107-826-11 1-107-826-11 1-107-826-11 1-125-891-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047uF 0.1uF 0.1uF 0.1uF 0.47uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 10V C981 C982 C991 C992 1-107-826-11 1-107-826-11 1-216-295-11 1-216-295-11 CERAMIC CHIP CERAMIC CHIP SHORT CHIP SHORT CHIP 0.1uF 0.1uF 0 0 10% 10% 16V 16V < CONNECTOR > CN901 1-820-619-11 PLUG, CONNECTOR 20P < DIODE > D882 D903 D904 D905 D906 8-719-057-80 8-719-057-80 8-719-057-80 8-719-977-12 8-719-977-12 DIODE DIODE DIODE DIODE DIODE MA8180-M-TX MA8180-M-TX MA8180-M-TX DTZ6.8B DTZ6.8B D907 D908 D971 8-719-977-12 DIODE DTZ6.8B 8-719-977-12 DIODE DTZ6.8B 8-719-420-90 DIODE MA8051-M < FERRITE BEAD > FB901 FB902 FB903 FB904 1-216-864-11 1-216-864-11 1-216-295-11 1-469-876-11 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 INDUCTOR, FERRITE BEAD < FLUORESCENT INDICATOR TUBE > FL901 1-519-909-12 INDICATOR TUBE, FLUORESCENT < IC > IC971 IC972 6-600-163-01 IC RS-770 (IR) 6-706-715-01 IC NJM2867F33(TE2) < DIODE > Ref. No. KEY The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board. Part No. Description LED843 LED844 LED845 LED846 LED847 8-719-078-21 8-719-078-21 8-719-078-21 8-719-078-21 8-719-078-21 LED LED LED LED LED SML-310PTT86 (OFF) (GT317EE) SML-310PTT86 (EQ3) (GT317EE) SML-310PTT86 (PTY) (GT317EE) SML-310PTT86 (SOURCE) (GT317EE) SML-310PTT86 (MODE) (GT317EE) Remark LED850 LED851 LED852 LED853 LED854 8-719-078-21 8-719-078-21 8-719-078-21 8-719-078-21 8-719-078-21 LED LED LED LED LED SML-310PTT86 (DSPL/DIM) (GT317EE) SML-310PTT86 (1/ALBM –) (GT317EE) SML-310PTT86 (2/ALBM +) (GT317EE) SML-310PTT86 (3/REP) (GT317EE) SML-310PTT86 (4/SHUF) (GT317EE) LED855 LED856 LED857 LED861 8-719-078-21 8-719-078-21 8-719-078-21 8-719-078-21 LED LED LED LED SML-310PTT86 (5) (GT317EE) SML-310PTT86 (6/PAUSE) (GT317EE) SML-310PTT86 (AF/TA) (GT317EE) SML-310PTT86 (RING ILLUMINATION) (GT317EE) LED862 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION) (GT317EE) LED863 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION) (GT317EE) LED864 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION) (GT317EE) LED941 8-719-053-09 LED SML-310VTT86 (Z) (GT360) LED942 8-719-053-09 LED SML-310VTT86 (CD INDICATOR) (GT360) LED943 8-719-053-09 LED SML-310VTT86 (OFF) (GT360) LED944 LED945 LED946 LED947 LED950 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 LED LED LED LED LED SML-310VTT86 (EQ3) (GT360) SML-310VTT86 (PTY) (GT360) SML-310VTT86 (SOURCE) (GT360) SML-310VTT86 (MODE) (GT360) SML-310VTT86 (DSPL/DIM) (GT360) LED951 LED952 LED953 LED954 LED955 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 LED LED LED LED LED SML-310VTT86 (1/ALBM –) (GT360) SML-310VTT86 (2/ALBM +) (GT360) SML-310VTT86 (3/REP) (GT360) SML-310VTT86 (4/SHUF) (GT360) SML-310VTT86 (5) (GT360) LED956 8-719-053-09 LED SML-310VTT86 (6/PAUSE) (GT360) LED957 8-719-053-09 LED SML-310VTT86 (AF/TA) (GT360) LED961 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) (GT360) LED962 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) (GT360) LED963 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) (GT360) LED841 8-719-078-21 LED SML-310PTT86 (Z) (GT317EE) LED842 8-719-078-21 LED SML-310PTT86 (CD INDICATOR) (GT317EE) 33 CDX-GT317EE/GT360 KEY Ref. No. Part No. Description Remark < SWITCH > LSW901 1-786-805-12 SWITCH, TACTILE (WITH LED) (M > SEEK +) (GT360) LSW901 1-786-806-12 SWITCH, TACTILE (WITH LED) (M > SEEK +) (GT317EE) LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED) (. m SEEK –) (GT360) LSW902 1-786-806-12 SWITCH, TACTILE (WITH LED) (. m SEEK –) (GT317EE) Ref. No. Part No. Description R905 R906 R907 R908 R909 1-216-823-11 1-216-820-11 1-216-821-11 1-216-821-11 1-216-822-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.5K 820 1K 1K 1.2K 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W R910 R911 R912 R913 R914 1-216-823-11 1-216-824-11 1-216-825-11 1-216-827-11 1-216-828-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.5K 1.8K 2.2K 3.3K 3.9K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R915 R921 R922 R941 1-216-830-11 1-216-295-11 1-216-295-11 1-216-813-11 METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP 5.6K 0 0 220 5% 1/10W 5% R942 1-216-813-11 METAL CHIP 220 5% 1/10W (GT360) 1/10W (GT360) R943 1-216-812-11 METAL CHIP 180 5% R944 1-216-811-11 METAL CHIP 150 5% R945 1-216-812-11 METAL CHIP 180 5% R946 1-216-811-11 METAL CHIP 150 5% R947 1-216-811-11 METAL CHIP 150 5% R947 1-216-812-11 METAL CHIP 180 5% R948 1-216-810-11 METAL CHIP 120 5% R948 1-216-811-11 METAL CHIP 150 5% R949 1-216-809-11 METAL CHIP 100 5% R950 1-216-809-11 METAL CHIP 100 5% R951 1-216-809-11 METAL CHIP 100 5% R952 1-216-809-11 METAL CHIP 100 5% R953 1-216-812-11 METAL CHIP 180 5% R954 1-216-811-11 METAL CHIP 150 5% R961 1-216-809-11 METAL CHIP 100 5% R962 1-216-809-11 METAL CHIP 100 5% R971 R975 R976 R977 1-216-809-11 1-216-811-11 1-216-811-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 150 150 100 5% 5% 5% 5% 1/10W (GT360) 1/10W 1/10W 1/10W 1/10W R978 R981 R982 R983 R988 1-216-864-11 1-218-893-11 1-216-841-11 1-216-864-11 1-216-864-11 SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP 0 82K 47K 0 0 0.5% 5% 1/10W 1/10W R989 1-216-845-11 METAL CHIP 5% 1/10W < TRANSISTOR > Q881 Q882 Q883 8-729-600-22 TRANSISTOR 2SA1235-F 8-729-600-22 TRANSISTOR 2SA1235-F 8-729-600-22 TRANSISTOR 2SA1235-F < RESISTOR > R841 1-216-810-11 METAL CHIP 120 5% R842 1-216-810-11 METAL CHIP 120 5% R843 1-216-811-11 METAL CHIP 150 5% R844 1-216-810-11 METAL CHIP 120 5% R845 1-216-811-11 METAL CHIP 150 5% R846 1-216-810-11 METAL CHIP 120 5% R849 1-216-807-11 METAL CHIP 68 5% R850 1-216-807-11 METAL CHIP 68 5% R851 1-216-807-11 METAL CHIP 68 5% R852 1-216-807-11 METAL CHIP 68 5% R853 1-216-811-11 METAL CHIP 150 5% R854 1-216-810-11 METAL CHIP 120 5% R861 1-216-811-11 METAL CHIP 150 5% R862 1-216-810-11 METAL CHIP 120 5% R863 1-216-811-11 METAL CHIP 150 5% 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) R864 1-216-810-11 METAL CHIP 120 5% R881 R882 R883 R884 1-216-821-11 1-216-821-11 1-216-821-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1K 10K 5% 5% 5% 5% 1/10W (GT317EE) 1/10W 1/10W 1/10W 1/10W R885 R886 R887 R888 R889 1-216-833-11 1-216-833-11 1-216-845-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R901 R902 R903 R904 1-216-820-11 1-216-821-11 1-216-821-11 1-216-822-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 820 1K 1K 1.2K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 34 100K 1/10W (GT360) 1/10W (GT360) 1/10W (GT360) 1/10W (GT360) 1/10W (GT317EE) 1/10W (GT360) 1/10W (GT317EE) 1/10W (GT360) 1/10W (GT360) 1/10W (GT360) 1/10W (GT360) 1/10W (GT360) 1/10W (GT360) 1/10W (GT360) 1/10W (GT360) CDX-GT317EE/GT360 KEY Ref. No. Part No. Description Remark Part No. Description < SWITCH > C151 C152 C153 C154 C155 1-126-960-11 1-126-960-11 1-126-961-11 1-163-017-00 1-163-017-00 ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP 1uF 1uF 2.2uF 0.0047uF 0.0047uF 20% 20% 20% 10% 10% 50V 50V 50V 50V 50V < ROTARY ENCODER > RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME) Ref. No. MAIN Remark S901 S902 S903 S904 S906 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 SWITCH, TACTILE (Z) SWITCH, TACTILE (OFF) SWITCH, TACTILE (SOURCE) SWITCH, TACTILE (EQ3) SWITCH, TACTILE (PTY) C200 C201 C202 C203 C204 1-107-826-11 1-124-234-00 1-107-826-11 1-126-965-11 1-107-826-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP 0.1uF 22uF 0.1uF 22uF 0.1uF 10% 20% 10% 20% 10% 16V 16V 16V 50V 16V S907 S908 S909 S910 S911 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 SWITCH, TACTILE (MODE) SWITCH, TACTILE (DSPL/DIM) SWITCH, TACTILE (1/ALBM –) SWITCH, TACTILE (2/ALBM +) SWITCH, TACTILE (3/REP) C205 C206 C207 C301 C302 1-126-965-11 1-107-826-11 1-126-965-11 1-115-340-11 1-162-970-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 22uF 0.1uF 22uF 0.22uF 0.01uF 20% 10% 20% 10% 10% 50V 16V 50V 25V 25V C303 C304 C305 C306 C307 1-128-551-11 1-115-340-11 1-162-970-11 1-124-261-00 1-162-970-11 ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 22uF 0.22uF 0.01uF 10uF 0.01uF 20% 10% 10% 20% 10% 63V 25V 25V 50V 25V C308 C309 C312 C313 C314 1-124-261-00 1-115-340-11 1-115-340-11 1-162-970-11 1-124-261-00 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 10uF 0.22uF 0.22uF 0.01uF 10uF 20% 10% 10% 10% 20% 50V 25V 25V 25V 50V C315 C316 C317 C318 C319 1-162-970-11 1-124-261-00 1-124-257-00 1-162-923-11 1-127-715-11 CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP 0.01uF 10uF 2.2uF 47PF 0.22uF 10% 20% 20% 5% 10% 25V 50V 50V 50V 16V C320 C325 C329 C330 C361 1-162-970-11 1-115-340-11 1-162-970-11 1-115-340-11 1-127-715-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.22uF 0.01uF 0.22uF 0.22uF 10% 10% 10% 10% 10% 25V 25V 25V 25V 16V C362 C363 C364 C365 C366 1-127-715-11 1-126-160-11 1-126-160-11 1-126-960-11 1-126-960-11 CERAMIC CHIP ELECT ELECT ELECT ELECT 0.22uF 1uF 1uF 1uF 1uF 10% 20% 20% 20% 20% 16V 50V 50V 50V 50V C401 C402 C403 C405 C409 1-124-234-00 1-162-970-11 1-124-584-00 1-124-234-00 1-124-261-00 ELECT CERAMIC CHIP ELECT ELECT ELECT 22uF 0.01uF 100uF 22uF 10uF 20% 10% 20% 20% 20% 16V 25V 10V 16V 50V C412 C413 C414 C415 C417 1-162-970-11 1-163-251-11 1-163-251-11 1-162-970-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 100PF 100PF 0.01uF 0.01uF 10% 5% 5% 10% 10% 25V 50V 50V 25V 25V C418 C419 C421 C423 C424 1-162-966-11 1-162-966-11 1-126-964-11 1-165-908-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.0022uF 0.0022uF 10uF 1uF 100PF 10% 10% 20% 10% 5% 50V 50V 50V 10V 50V C426 C431 C432 1-165-908-11 CERAMIC CHIP 1-124-261-00 ELECT 1-163-251-11 CERAMIC CHIP 1uF 10uF 100PF 10% 20% 5% 10V 50V 50V S912 1-786-653-21 SWITCH, TACTILE (4/SHUF) S913 1-786-653-21 SWITCH, TACTILE (5) S914 1-786-653-21 SWITCH, TACTILE (6/PAUSE) S915 1-786-653-21 SWITCH, TACTILE (AF/TA) ************************************************************* A-1206-400-A MAIN BOARD, COMPLETE (GT317EE) A-1206-410-A MAIN BOARD, COMPLETE (GT360) ********************* 7-621-284-40 SCREW +P 2.6X10 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-794-09 SCREW +PTT 2.6X10 (S) < CAPACITOR > C1 1-126-963-11 ELECT 4.7uF 20% C2 C3 C5 C6 1-126-947-11 1-162-970-11 1-126-947-11 1-162-970-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP 47uF 0.01uF 47uF 0.01uF 20% 10% 20% 10% C7 C8 C15 1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 0.01uF 0.01uF 0.1uF 10% 10% 10% C50 1-107-826-11 CERAMIC CHIP 0.1uF 10% C51 1-107-826-11 CERAMIC CHIP 0.1uF 10% C52 1-107-826-11 CERAMIC CHIP 0.1uF 10% C53 1-107-826-11 CERAMIC CHIP 0.1uF 10% C54 1-107-826-11 CERAMIC CHIP 0.1uF 10% C55 1-107-826-11 CERAMIC CHIP 0.1uF 10% C56 1-164-237-11 CERAMIC CHIP 16PF 5% C57 1-164-237-11 CERAMIC CHIP 16PF 5% C58 1-162-959-11 CERAMIC CHIP 330PF 5% C60 1-162-970-11 CERAMIC CHIP 0.01uF 10% C61 1-126-947-11 ELECT 47uF 20% 50V (GT317EE) 35V 25V 35V 25V 25V 25V 16V (GT360) 16V (GT317EE) 16V (GT317EE) 16V (GT317EE) 16V (GT317EE) 16V (GT317EE) 16V (GT317EE) 50V (GT317EE) 50V (GT317EE) 50V (GT317EE) 25V (GT317EE) 35V (GT317EE) 35 CDX-GT317EE/GT360 MAIN Ref. No. Part No. Description Part No. Description C434 C441 C443 C444 C445 1-162-927-11 1-126-964-11 1-165-908-11 1-162-927-11 1-165-908-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 10uF 1uF 100PF 1uF 5% 20% 10% 5% 10% Remark 50V 50V 10V 50V 10V D109 D110 D111 D112 D113 8-719-977-12 8-719-977-12 8-719-977-12 8-719-977-12 8-719-977-12 DIODE DIODE DIODE DIODE DIODE DTZ6.8B DTZ6.8B DTZ6.8B DTZ6.8B DTZ6.8B C451 C452 C454 C461 C462 1-126-964-11 1-163-251-11 1-162-927-11 1-126-964-11 1-165-908-11 ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 10uF 100PF 100PF 10uF 1uF 20% 5% 5% 20% 10% 50V 50V 50V 50V 10V D153 D200 D201 D202 D203 8-719-977-12 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE DTZ6.8B 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 C463 C471 C472 C473 C484 1-165-908-11 1-126-964-11 1-165-908-11 1-165-908-11 1-107-826-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 10uF 1uF 1uF 0.1uF 10% 20% 10% 10% 10% 10V 50V 10V 10V 16V D204 D205 D206 D207 D301 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 C485 C486 C491 C501 C502 1-126-933-11 1-126-964-11 1-124-589-11 1-162-970-11 1-162-964-11 ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP 100uF 10uF 47uF 0.01uF 0.001uF 20% 20% 20% 10% 10% 16V 50V 16V 25V 50V D302 D303 D304 D305 D306 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 C504 C507 C508 C509 C510 1-162-970-11 1-162-917-11 1-162-917-11 1-164-227-11 1-165-908-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 15PF 15PF 0.022uF 1uF 10% 5% 5% 10% 10% 25V 50V 50V 25V 10V D307 D308 D309 D310 D311 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 C512 C513 C514 C519 C600 1-162-964-11 1-162-970-11 1-162-964-11 1-107-826-11 1-126-935-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 0.001uF 0.01uF 0.001uF 0.1uF 470uF 10% 10% 10% 10% 20% 50V 25V 50V 16V 16V D312 D353 D491 D491 D493 6-500-522-01 6-501-013-01 6-501-193-01 8-719-988-61 6-501-051-01 DIODE DIODE DIODE DIODE DIODE 10EDB40-TA1B2 BAT54ALT1G 1SS355WTE-17 (GT360) 1SS355TE-17 (GT317EE) BAT54CLT1G C601 C622 C623 C681 C682 1-162-970-11 1-126-924-11 1-126-916-11 1-162-970-11 1-162-970-11 CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP 0.01uF 330uF 1000uF 0.01uF 0.01uF 10% 20% 20% 10% 10% 25V 10V 6.3V 25V 25V D502 D503 D503 D602 D603 8-719-060-48 6-501-193-01 8-719-988-61 8-719-057-80 8-719-422-64 DIODE DIODE DIODE DIODE DIODE RB751V-40TE-17 1SS355WTE-17 (GT360) 1SS355TE-17 (GT317EE) MA8180-M-TX MA8062-M C683 C701 C702 C703 C704 1-124-584-00 1-131-868-81 1-164-005-11 1-164-005-11 1-115-340-11 ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100uF 3300uF 0.47uF 0.47uF 0.22uF 20% 20% 10% 10V 16V 25V 25V 25V D604 D605 D606 D607 D609 8-719-057-80 8-719-057-80 8-719-072-70 6-501-571-01 6-501-051-01 DIODE DIODE DIODE DIODE DIODE MA8180-M-TX MA8180-M-TX MA2ZD14001S0 1N5404-C311-3 BAT54CLT1G C705 C997 C998 1-115-340-11 CERAMIC CHIP 1-163-009-11 CERAMIC CHIP 1-163-009-11 CERAMIC CHIP 0.22uF 0.001uF 0.001uF 10% 10% 10% 25V 50V 50V D702 D703 D704 D901 D998 8-719-057-80 8-719-977-12 8-719-057-80 8-719-057-80 8-719-057-80 DIODE DIODE DIODE DIODE DIODE MA8180-M-TX DTZ6.8B MA8180-M-TX (GT317EE) MA8180-M-TX MA8180-M-TX PIN, CONNECTOR 16P CONNECTOR, BOARD TO BOARD 28P SOCKET, CONNECTOR 20P PLUG, CONNECTOR 8P (BUS CONTROL IN) D999 8-719-057-80 DIODE MA8180-M-TX < CONNECTOR > CN300 CN350 CN370 CNJ400 1-774-701-21 1-820-611-11 1-820-622-11 1-580-907-41 < DIODE > D2 D101 D103 D104 D105 8-719-977-03 8-719-977-12 8-719-977-12 8-719-977-12 8-719-977-12 D106 D108 8-719-057-80 DIODE MA8180-M-TX 8-719-977-12 DIODE DTZ6.8B 36 DIODE DIODE DIODE DIODE DIODE DTZ5.6B DTZ6.8B DTZ6.8B DTZ6.8B DTZ6.8B Ref. No. Remark < IC > IC50 IC200 IC201 IC202 IC203 6-803-747-01 6-709-213-01 6-709-213-01 6-709-213-01 6-709-213-01 IC IC IC IC IC TDA7333013TR (GT317EE) NJM2387ADL3(TE2) NJM2387ADL3(TE2) NJM2387ADL3(TE2) NJM2387ADL3(TE2) IC300 IC401 IC501 IC501 IC601 6-705-359-02 6-710-065-01 6-710-298-01 6-807-262-01 6-703-884-01 IC IC IC IC IC TDA8588AJ/N2/R1 BD3442FS-E2 MB90F045PF-G-9015-SPE1 (GT360) MB90F045PF-G-9043-SPE1 (GT317EE) BA8271F-E2 CDX-GT317EE/GT360 MAIN Ref. No. IC602 IC681 Part No. Description Remark 8-759-659-13 IC PST3428UL 6-705-373-01 IC MM3123DPLE < JACK > J1 J652 1-815-185-13 JACK (ANTENNA) 1-774-699-12 JACK, PIN 4P (BUS AUDIO IN, AUDIO OUT REAR) < JUMPER RESISTOR > JC1 JC2 JC3 JC4 JC5 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC6 JC7 JC8 JC9 JC10 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC11 JC12 JC13 JC14 JC15 1-216-864-11 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC16 JC17 JC18 JC19 JC20 1-216-296-11 1-216-864-11 1-216-864-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC21 JC22 JC23 JC24 JC25 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC26 JC27 JC28 JC29 JC30 1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC31 JC32 JC33 JC34 JC35 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 JC36 JC37 JC38 JC40 JC41 1-216-864-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 (GT317EE) 0 0 JC42 1-216-296-11 SHORT CHIP 0 Ref. No. Part No. Description L5 L50 L151 L300 L401 1-414-595-11 1-469-844-11 1-216-295-11 1-456-617-11 1-216-864-11 INDUCTOR, FERRITE BEAD (GT317EE) INDUCTOR 2.2uH (GT317EE) SHORT CHIP 0 COIL, CHOKE SHORT CHIP 0 Remark L402 L403 L405 L406 L407 1-216-295-11 1-216-295-11 1-216-864-11 1-500-245-11 1-216-864-11 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 INDUCTOR, FERRITE BEAD SHORT CHIP 0 L409 L410 L501 L901 L902 1-469-844-11 1-469-876-11 1-469-844-11 1-216-295-11 1-469-844-11 INDUCTOR 2.2uH INDUCTOR, FERRITE BEAD INDUCTOR 2.2uH SHORT CHIP 0 INDUCTOR 2.2uH < TRANSISTOR > Q1 Q3 Q50 Q420 Q432 8-729-027-43 6-551-431-01 8-729-600-22 8-729-027-44 6-550-752-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114EKA-T146 (GT317EE) 2SC6027T100-QR 2SA1235-F (GT317EE) DTC114TKA-T146 DTC614TKT146 Q440 Q452 Q460 Q470 Q491 8-729-027-44 6-550-752-01 8-729-027-44 8-729-027-44 8-729-027-23 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114TKA-T146 DTC614TKT146 DTC114TKA-T146 DTC114TKA-T146 DTA114EKA-T146 Q492 Q600 Q601 Q605 Q664 8-729-027-43 8-729-047-76 8-729-027-23 8-729-027-43 8-729-027-23 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114EKA-T146 FMC2A-T148 DTA114EKA-T146 DTC114EKA-T146 DTA114EKA-T146 Q701 Q702 8-729-120-28 TRANSISTOR 2SC1623-L5L6 (GT317EE) 8-729-120-28 TRANSISTOR 2SC1623-L5L6 < RESISTOR > R1 1-216-809-11 METAL CHIP 100 5% R2 R3 R4 R5 1-216-839-11 1-216-843-11 1-216-839-11 1-216-843-11 33K 68K 33K 68K 5% 5% 5% 5% R6 R7 R8 1-414-595-11 INDUCTOR, FERRITE BEAD 1-414-595-11 INDUCTOR, FERRITE BEAD 1-216-839-11 METAL CHIP 33K 5% R9 R10 1-216-843-11 METAL CHIP 1-216-821-11 METAL CHIP 68K 1K 5% 5% R12 R13 R15 R52 1-216-811-11 1-216-811-11 1-216-864-11 1-216-845-11 150 5% 150 5% 0 (GT317EE) 100K 5% R53 1-216-797-11 METAL CHIP R54 R55 1-414-595-11 INDUCTOR, FERRITE BEAD (GT317EE) 1-216-797-11 METAL CHIP 10 5% 1/10W (GT317EE) METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP < COIL > L1 L2 L3 L4 L5 1-216-295-11 1-414-595-11 1-414-595-11 1-469-844-11 1-216-864-11 SHORT CHIP 0 INDUCTOR, FERRITE BEAD (GT317EE) INDUCTOR, FERRITE BEAD (GT317EE) INDUCTOR 2.2uH SHORT CHIP 0 (GT360) 10 5% 1/10W (GT317EE) 1/10W 1/10W 1/10W 1/10W 1/10W (GT317EE) 1/10W 1/10W 1/10W 1/10W 1/10W (GT317EE) 1/10W (GT317EE) 37 CDX-GT317EE/GT360 MAIN Ref. No. Part No. Description Remark R57 1-216-833-11 METAL CHIP 10K 5% R58 1-216-821-11 METAL CHIP 1K 5% R151 R152 R153 1-216-817-11 METAL CHIP 1-216-817-11 METAL CHIP 1-216-834-11 METAL CHIP 470 470 12K 5% 5% 5% 1/10W (GT317EE) 1/10W (GT317EE) 1/10W 1/10W 1/10W R154 R155 R200 R201 R202 1-216-834-11 1-216-825-11 1-216-833-11 1-216-822-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 12K 2.2K 10K 1.2K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R203 R204 R205 R206 R207 1-216-829-11 1-216-821-11 1-216-845-11 1-216-822-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 1K 100K 1.2K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R208 R209 R210 R211 R301 1-218-344-11 1-216-821-11 1-216-812-11 1-216-821-11 1-216-811-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 7.5K 1K 180 1K 150 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R302 R351 R355 R356 R357 1-216-841-11 1-216-845-11 1-216-833-11 1-216-833-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 100K 10K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R358 R401 R402 R420 R421 1-216-821-11 1-216-821-11 1-216-821-11 1-216-809-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1K 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R430 R431 R440 R442 R447 1-216-809-11 1-216-809-11 1-216-809-11 1-216-821-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 1K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R448 R449 R450 R451 R452 1-216-833-11 1-216-833-11 1-216-833-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R460 R461 R462 R470 R471 1-216-809-11 1-216-821-11 1-216-833-11 1-216-809-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 1K 10K 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R472 R481 R485 R491 R502 1-216-833-11 1-216-801-11 1-218-883-11 1-216-805-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 22 33K 47 100 5% 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R503 R504 R505 R507 1-216-809-11 1-218-871-11 1-218-871-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 10K 10K 100K 5% 0.5% 0.5% 5% R509 1-216-809-11 METAL CHIP 100 5% 1/10W 1/10W 1/10W 1/10W (GT360) 1/10W 38 Ref. No. Part No. Description R510 R511 R512 R517 R519 1-216-864-11 1-216-809-11 1-216-809-11 1-216-841-11 1-216-845-11 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 100 100 47K 100K Remark 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R520 R521 R522 R523 R524 1-216-809-11 1-216-825-11 1-216-825-11 1-216-809-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 2.2K 2.2K 100 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R525 R526 R529 R531 R532 1-216-833-11 1-216-845-11 1-216-809-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100K 100 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R533 R534 R537 1-216-845-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-845-11 METAL CHIP 100K 10K 100K 5% 5% 5% R538 1-216-845-11 METAL CHIP 100K 5% R539 1-216-845-11 METAL CHIP 100K 5% 1/10W 1/10W 1/10W (GT360) 1/10W (GT317EE) 1/10W (GT317EE) R540 1-216-845-11 METAL CHIP 100K 5% R544 R549 1-216-809-11 METAL CHIP 1-216-845-11 METAL CHIP 100 100K 5% 5% R550 1-216-845-11 METAL CHIP 100K 5% R551 1-216-845-11 METAL CHIP 100K 5% R552 1-216-845-11 METAL CHIP 100K 5% R553 R555 R556 R557 1-216-845-11 1-216-845-11 1-216-845-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 100 5% 5% 5% 5% R558 R560 R561 R563 R564 1-216-833-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W (GT317EE) R565 R566 1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP 100K 100K 5% 5% R567 R568 R570 1-216-845-11 METAL CHIP 1-216-849-11 METAL CHIP 1-216-809-11 METAL CHIP 100K 220K 100 5% 5% 5% 1/10W 1/10W (GT360) 1/10W 1/10W 1/10W R573 1-216-845-11 METAL CHIP 100K 5% R600 R601 R602 R603 1-216-845-11 1-216-851-11 1-216-851-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 330K 330K 1K 5% 5% 5% 5% 1/10W (GT317EE) 1/10W 1/10W 1/10W 1/10W R604 R606 R607 R608 1-216-835-11 1-216-821-11 1-216-821-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 15K 1K 1K 4.7K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W (GT360) 1/10W 1/10W (GT317EE) 1/10W (GT360) 1/10W (GT360) 1/10W (GT317EE) 1/10W 1/10W 1/10W 1/10W CDX-GT317EE/GT360 MAIN Ref. No. Part No. Description R610 R611 R612 R615 R616 1-216-809-11 1-216-864-11 1-216-864-11 1-216-809-11 1-216-864-11 METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP SHORT CHIP 100 0 0 100 0 5% 1/10W 5% 1/10W R636 R671 R672 R673 R674 1-216-845-11 1-216-809-11 1-216-809-11 1-216-833-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100 100 10K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R701 1-216-821-11 METAL CHIP 1K 5% R702 1-216-841-11 METAL CHIP 47K 5% R703 1-216-833-11 METAL CHIP 10K 5% R704 1-216-833-11 METAL CHIP 10K 5% R705 1-249-425-11 CARBON 4.7K 5% 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/10W (GT317EE) 1/4W R706 R707 R708 R709 1-216-841-11 1-216-841-11 1-216-829-11 1-216-833-11 47K 47K 4.7K 10K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W METAL CHIP METAL CHIP METAL CHIP METAL CHIP Remark Ref. No. Remark 1-479-077-13 REMOTE COMMANDER (RM-X151) 2-548-729-01 LID, BATTERY CASE (for RM-X151) 2-886-504-21 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN) (GT317EE) 2-886-504-41 MANUAL, INSTRUCTION (ENGLISH) (GT360) 2-886-505-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH, RUSSIAN) (GT317EE) 2-886-505-41 MANUAL, INSTRUCTION, INSTALL (ENGLISH) (GT360) X-2149-228-2 CASE ASSY (for FRONT PANEL) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 151 152 153 154 155 X-3382-647-1 2-686-803-01 3-246-471-01 X-3381-154-1 3-349-410-11 156 157 1-465-459-31 ADAPTOR, ANTENNA (GT317EE) 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER) (GT317EE) 1-833-100-11 CORD (WITH CONNECTOR) (POWER) (GT360) 158 FRAME ASSY, FITTING COLLAR KEY (FRAME) SCREW ASSY (BS4), FITTING BUSHING 1-786-826-11 SWITCH, TACTILE (RESET) < THERMISTOR (POSITIVE) > TH400 Description ACCESSORIES ************ < SWITCH > S103 Part No. 151 152 153 1-803-350-21 THERMISTOR, POSITIVE < TUNER UNIT > TU1 TU1 SERVO A-3220-960-B TUNER UNIT (TUX-032) (GT360) A-3220-961-B TUNER UNIT (TUX-032) (GT317EE) ×2 154 155 < VIBRATOR > X50 1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz) (GT317EE) X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz) X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz) ************************************************************* ×4 156 157 158 A-1177-201-A SERVO BOARD, COMPLETE ********************** ************************************************************* MISCELLANEOUS *************** 7 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER) (GT317EE) 7 1-833-100-11 CORD (WITH CONNECTOR) (POWER) (GT360) 0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A) F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A J901 1-820-624-11 JACK (SMALL TYPE) (VERTICAL) (AUX) ************************************************************* 39 CDX-GT317EE/GT360 MEMO 40 CDX-GT317EE/GT360 Saudi Arabia Model CDX-GT360 East European Model SERVICE MANUAL CDX-GT317EE Ver. 1.1 2007.03 SUPPLEMENT-1 File this supplement with the service manual. Subject: Notes for removal of the OPTICAL PICK-UP added. DISASSEMBLY 1. CHUCKING ARM SUB ASSY 3 chucking arm sub assy 1 spring 2 Note: Have this portion receive the chassis. Note: Have this portion receive the chassis. Note: Be careful not to touch the turn table. 9-887-460-81 CDX-GT317EE/GT360 2. SLED MOTOR ASSY 2 three serration screws (M 2 × 3) 3 sled mtor assy 1 spring turn table spring stand Note: Never remove these parts since they were adjusted. stand Note: Place the stand with care not to touch the turn table. Note for Assembly three serration screws (M 2 × 3) sled mtor assy Note: Take care to prevent the chassis from being bent when tightening the three machine screws. 2 CDX-GT317EE/GT360 3. OPTICAL PICK-UP SECTION 2 optical pick-up section 1 Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section. 4. OPTICAL PICK-UP 1 pan tapping screw (M 1.4 × 2.5) 2 leaf spring (sub guide) 3 leaf spring (OP) 5 optical pick-up 4 lead screw assy Notes for Assembly Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base. Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base. There is space at the end of the leaf spring (sub guide) to avoid contact with the slide. 3 CDX-GT317EE/GT360 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1.0 2006.10 New 1.1 2007.03 Notes for removal of the OPTICAL PICK-UP added. (SUPPLEMENT-1) 4 (ENG-07003) www.s-manuals.com