Download The 45 Performance Book

Transcript
Cam Covers
With 1 exception (marked *), all 45 cam covers are identical in appearance from outside, and are based on
the same casting (131-372, which appears inside the cover in most cases). There are a wide variety of models
used, of which the most common types appear below:
Description & Notes
Model
Type Part NQ
Plain brass bushings in all positions, 12%" long, fins run the full length of
1937-57, all
l.00 25201-37
the cover. 1/4" generator screw holes. #2 bushing boss is 5/ 16" tall. Must
models
use early #2 cam. Cslg # 131-372
As 1.00, except '/16" generator screw holes
1958 G
1.01 25201-58
1959-73 G, GE, As 1.01, except #2 bushing boss is 'h2" tall. Must use late #2 cam. Cslg #
1.02 25200-59
25202-37
GA
As
1.00, except dual-position (figure "8") idler boss for front-drive mag­
1939-41
80584-39
1.10
WLDD,WLDR neto or generator
Ball brg. in #2, 3 & 4 positions; no ignition drive on #2; breaker boss has
80584-41
1941-46 WR
2.00
drive hole cover plate; Idler boss for front-drive magneto
Same as 2.00, except breaker mounting area is deleted from cover casting
2.01 R0584-47 1947 WR
Ball brg. in #3 & 4 positions; idler boss for front-drive magneto; breaker
2.10 R0584-48 1948-49 WR
hole has removable cover plate
Ball brg. in #3 & 4; different casting & fin pattern; idler boss for front2.20* 25201-50R 1950-52 WR
drive magneto; removable access plate (25720-50r) on face of cam cover
for magneto drive
Description & Notes
Model
Type Part NQ
1932-36 RLDR
Intake only, used with std. exhaust cams, asymmetrical lobe
.90 80610-32
80611-32
shape, no s£ecs
l.00 2550X-37
1937-58 all std. motors 240° duration, .312" (5/ 16") lift, large-diameter journals for plain
brass bushings
1959-73 G, GE, GA
1.01 2550X-59
#1,3 & 4 identical to Type 1.00 above; #2 has less undercut on
cover side of gear
1.02 80610-39
1937-41 WLDR
Intake only, used with std. exhaust cams, asymmetrical lobe
80611-39
shape?, no specs
1.10 R0600-39
1939-41 WLDR; 1940A As 1.00, except 270°, .320" lift
WLDR (Special)
1.11 25505-02R 45 special
As 1.10, supplied by KNS Cycle as a regrind
2.00 R0600-41
1941-47 WRCD
Duration 300°+, .344" lift, ball brgs. on #2,3, & 4 in cam cover,
lobe peaks are nearly flat on top, for use with flat t'!J)Qets only
2.10 R0600-48
1948-52 WR
As 3.00, except ignition spiral drive on #2, ball brgs. on #3 & 4
in cam cover, flat tappets only
3.00 255XX-53
1952-56 K, KH
Similar to 1.10, but .344" lift, #2 cam gear wider than 45, all
lobes are tapered (intake 1°2' L, exhaust 3°32' L?)
3.10 . 255XX-56R 1952-56 KK, KHK
As 2.00, except very broad lobe, concave (hollow) flanks, .375"
lift, all lobes are tapered
4.00 255XX-53R 1953-55 KRM,
Similar to 3.00 but has plain journals, for flat tappets only, all
lobes are tapered
KHRMCD
5.00 25499-53R 1953-69 KR, KHRCD,
As 3.10, except 295-315°, .395-.440" lift (various grinds, see
&c.
following tables*), very broad lobes, ball brgs. on #1, 3 & 4 in
cover, all lobes are tapered
Note: al13.XX - 5.XX cams above have tapered lobes, exhausts are tapered more than intake.
Note: all cams listed above are suitable for roller tappets only, except as noted.
Page 36 of39
"45 Performance", by VICTORY LIBRARY
May 15,2005