Download Service Manual of Sony DSC-S730 Digital Camera
Transcript
DSC-S730 SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Tourist Model Ver. 1.0 2007.11 Revision History Internal memory ON BOARD Link SPECIFICATIONS DISASSEMBLY SERVICE NOTE BLOCK DIAGRAM The components identified by mark or dotted line with mark are critical for safety. Replace only with part number specified. REPAIR PARTS LIST Les composants identifiés par une marque sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. In case of the lens block assy, main board, or main frame assembly failure, contact your local Sony Service Headquarter for the measures. DIGITAL STILL CAMERA DSC-S730 9-852-239-11 Sony EMCS Co. 2007K0200-1 © 2007.11 Published by Kohda TEC SPECIFICATIONS [System] [LCD screen] Image device: 7.20 mm (1/2.5 type) color CCD, Primary color filter Total pixel number of camera: Approx. 7 410 000 pixels Effective pixel number of camera: Approx. 7 201 000 pixels Lens: 3× zoom lens f = 5.8 – 17.4 mm (35 – 105 mm when converted to a 35 mm still camera) F2.8 (W) – 4.8 (T) Exposure control: Automatic exposure, Scene Selection (7 modes) White balance: Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash File format (DCF compliant): Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: AVI (Motion JPEG) Recording media: Internal Memory (approx. 22 MB), "Memory Stick Duo" Flash: Flash range (ISO sensitivity (Recommended Exposure Index) set to Auto): approx. 0.5 to 3.5 m (1 feet 7 3/4 inches to 11 feet 5 7/8 inches) (W)/approx. 0.5 to 2.0 m (1 feet 7 3/4 inches to 6 feet 6 3/4 inches) (T) LCD panel: 6.0 cm (2.4 type) TFT drive Total number of dots: 112 320 (480×234) dots [Power, general] Power: LR6 (size AA) Alkaline batteries (2), 3 V HR15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2) (not supplied), 2.4 V ZR6 (size AA) Oxy Nickel Primary Battery (2) (not supplied), 3 V AC-LS5K AC Adaptor (not supplied), 4.2 V Power consumption (during shooting): 1.2 W Operating temperature: 0 to 40 C (32 to 104 F) Storage temperature: –20 to +60 C (–4 to +140 F) Dimensions: 91.4×61.0×29.1 mm (3 5/8×2 1/2× 1 3/16 inches) (W/H/D, excluding protrusions) Mass: Approx. 189 g (6.7 oz) (including two batteries and strap, etc.) Microphone: Monaural Buzzer Exif Print: Compatible PRINT Image Matching III: Compatible PictBridge: Compatible [Input and Output connectors] (USB) A/V OUT terminal: Video, Audio (Monaural), USB communication USB communication: Hi-Speed USB (USB 2.0 compliant) DSC-S730 Design and specifications are subject to change without notice. —2— CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITH MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. 2. 3. 4. 5. 6. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. FLEXIBLE Circuit Board Repairing Keep the temperature of the soldering iron around 270 C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. DSC-S730 Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. —3— TABLE OF CONTENTS Section 1. Title Page SERVICE NOTE 1-1. Process After Fixing Flash Error ····································· 1-1 1-2. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-1 2. DISASSEMBLY 2-1. Disassembly ····································································· 2-1 3. BLOCK DIAGRAM 3-1. Overall Block Diagram ··················································· 3-1 4. REPAIR PARTS LIST 4-1. Exploded Views ······························································· 4-1 4-1-1. Overall Section ······························································ 4-1 4-1-2. Main Frame Block ························································· 4-2 4-2. Accessories ······································································ 4-3 DSC-S730 —4— 1. SERVICE NOTE 1-1. PROCESS AFTER FIXING FLASH ERROR Method for Initializing the Flash Error Initialize Initializes the setting to the default setting. Even if you execute this function, the images stored in the internal memory are retained. 1 Select [OK] with v on the control button, then press z. The message "Initialize all settings Ready?" appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting. To cancel initializing Select [Cancel] in step 1 or 2, then press z. Be sure not to power off the camera while initializing. 1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note: When replacing the camera, erase the data in internal memory of the board before replacement. Method for Copying the Data in Internal Memory Copy Copies all images in the internal memory to a "Memory Stick Duo". 1 Insert a "Memory Stick Duo" having sufficient free capacity. 2 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be copied Ready?" appears. 3 Select [OK] with v, then press z. Copying starts. To cancel copying Select [Cancel] in step 2 or 3, then press z. Use batteries with enough power remaining. If you attempt to copy image files using batteries with little remaining charge, the batteries may run out, causing copying to fail or possibly corrupting the data. You cannot select images to copy. The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the "Memory Stick Duo" after copying, then format the internal memory ([Format] in [Internal Memory Tool]). A new folder is created on the "Memory Stick Duo" and all the data will be copied to it. You cannot choose a specific folder and copy images to it. The (Print order) marks on the images are not copied. Method for Formatting the Internal Memory This item does not appear when a "Memory Stick Duo" is inserted in the camera. Format Formats the internal memory. Note that formatting permanently erases all data in the internal memory, including even protected images. 1 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be erased Ready?" appears. 2 Select [OK] with v, then press z. The format is complete. To cancel formatting Select [Cancel] in step 1 or 2, then press z. DSC-S730 1-1 2. DISASSEMBLY The following flow chart shows the disassembly procedure. 2-1. DISASSEMBLY 5 3 2 4 2 1 3 1 4 1 Open the BT LID 1 SCREW TP 1.4 X 3.5 2 SCREW M 1.7 X 2.7 2 SCREW TP 1.4 X 4 3 SCREW TP 1.7 X 4 3 LCD 4 SCREW TP 1.7 X 3.5 4 LCD PLATE 5 CABINET (REAR) ASSY 2 plate (To 2-2 Page) 3 1 3 1 Note : When CABINET(FRONT) ASSY is removed, the plate will bends if CABINET(FRONT) ASSY is inclined too much. Please remove CABINET (FRONT) ASSY as in parallel as possible. 2 1 BT LID SHAFT 2 BT LID 3 BT LID SPRING DSC-S730 2-1 1 SCREW TP 1.4 X 3 2 SCREW TP 1.4 X 2.5 3 CABINET (FRONT) ASSY 1 1 2 3 2 3 3 2 (From 2-1 Page) 1 4 Caution 1 SCREW TP 1.4 X 2.5 Shorting jig (1kΩ / 1W) Note : After discharged, a transparent seal is put again. Do not lose the transparent seal removed when discharged. 1 STRAP SHAFT 1 SCREW TP 1.7 X 3.5 2 SCREW TP 1.7 X 3.5 2 SCREW TP 1.4 X 3 2 SCREW TP 1.7 X 6.5 3 MAIN MOUNT 3 RL BLOCK 3 ST BLOCK ASSY 4 SUPPORT (JACK) 1 2 4 3 5 1 JACK LID 2 SCREW TP 1.4 X 3 3 LENS BLOCK ASSY 4 LID 5 MAIN FRAME DSC-S730 2-2 3. BLOCK DIAGRAM 3-1. OVERALL BLOCK DIAGRAM MAIN BOARD LC D LCD_BACKLIGHT 1 STROBE & TOP BOARD RED LC D_E N LC D_MC LK LC D_V D LC D_HD LC D_S C LK LC D_S DA T A LC D [0 ..7 ] MLC D_O N BL LC D_E N LC D_MC LK LC D_VD LC D_HD LC D_SC LK LC D_SDATA LC D[0..7] MLC D_ON BL P X C LK HD VD C DS _E N S C LK S DA T A A F E RS T T G _E N V S UB _C on1 V S UB _C on2 C C D_O N T G _O N C DS _O N C C D[0..11 ] PXC LK HD VD C DS_E N SC LK SDATA AF E RST TG_E N VSUB_C on1 VSUB_C on2 C C D_ON TG_ON C DS_ON C C D[0..11] LC D_E N LC D_MC LK LC D_VD LC D_HD LC D_SC LK LC D_SDATA LC D[0..7] MLC D_ON BL DG ND DGND 2 LENS BLOCK C DS DS P +5V M +3.1V D +5VM +3.1VD AUO LCD 2.36 INCH PANEL PXC LK HD VD C DS_E N SC LK SDATA AF E RST TG_E N VSUB_C on1 VSUB_C on2 C C D_ON TG_ON C DS_ON C C D[0..11] +3.3V +3.3V -7.5V -7.5V DG ND DGND C DS DGND DDR TOP RAMD[0..15] RAMA[0..14] RAMLDM RAMW E _N RAMC AS RAMRAS RAMC S_N RAMLDQS RAMUDQS RAMUDM RAMC LK_N RAMC LK RAMC LK_E N RAMRE F POWER LED +2.5V D 2 GREEN 1 +2.5VD DG ND 2 P1,P2 F LA S H_V P FLASH CHARGER 1 Q5 1 2 DGND FLASH TUBE S NC 3 MS _O N R/B MS _INS # C LE WE WP A LE CE 0 RE MS _C LK MD [0 ..7] F A 23 F A 20 F A 22 F A 21 MS_ON R/B MS_INS# C LE WE WP ALE CE0 RE MS_C LK MD[0..7] F A23 F A20 F A22 F A21 RAMD[0..15] RAMA[0..14] RAMLDM RAMW E _N RAMC AS RAMRAS RAMC S_N RAMLDQS RAMUDQS RAMUDM RAMC LK_N RAMC LK RAMC LK_E N RAMRE F DDR 1 ME MO RY 3 BE E PE R BE E PE R 2 F LA S H_RDY F LA S H_C HG _L S T RO B E _T RG S T RO B E _C HG A F _LE D S T RO B E _P W R F LASH_RDY F LASH_C HG_L STROBE _TRG STROBE _C HG AF _LE D STROBE _PW R FOCUS MOTOR LE NS _E N LE NS _S C LK LE NS _S DA T A Z O O M_P I Z O O M_P R F O C US _P I +5V M DG ND LE NS_E N LE NS_SC LK LE NS_SDATA ZOOM_PI ZOOM_PR F OC US_PI F LA S H MODE DIAL FUNCTION KEY 12MHZ 1 +3.3V +3.1V D +5V M +1.8V D +3.3V +3.1V D +3.1VD +3.3V S +5VM +13.4V +1.8V D +3.3V +13.4V C C D_ON +1.8VD DGND C C D_O N +2.5V D DG ND DG ND S W _T E LE SW _TE LE 5 VP +2.5VD S W _W IDE SW _W IDE PW R_C TRL 2 1 -7.5V +2.5V D C C D_ON1 VP +1.8VD +3.1VD +3.3VS +3.3V +2.5VD DGND 32.768K Hz 4 C C D_O N1 P W R_C T RL 1 PW R_C TRL MIC _N VP -7.5V MIC C C D_ON1 VP JA C K S W _P LA Y B A C K SW _PLAYBAC K 6 2 PO WE R 4 SW PC UG ND UGND 5 DGND SW _KE Y_ADC 1 SW _KE Y_ADC DG ND DGND 1 S W _K E Y _A DC 1 S W _K E Y _A DC SW _KE Y_ADC 1 SW _KE Y_ADC +3.1V D +3.1VD 6 STA_LE D D+ DUSB_DE T A/V_DE T VIDE O_OUT LINE _OUT BE E PE R 3 S T A _LE D D+ DUS B _DE T A V _DE T V IDE O _O UT LINE _O UT BE E PE R D+ DUSB_DE T AV_DE T VIDE O_OUT LINE _OUT BE E PE R 5 DG ND SHUTTER MOTOR JA C K 2 GREEN STA_LE D +3.1VD IRIS MOTOR LE NS SW +3.1V D LE NS_E N LE NS_SC LK LE NS_SDATA ZOOM_PI ZOOM_PR F OC US_PI +5VM DGND P W R_O N P W RK E Y B A T _LO A D PW R_ON PW RKE Y BAT_LOAD MS LED 1 FOCUS SENSOR 2 DGND F LASH_RDY F LASH_C HG_L STROBE _TRG STROBE _C HG AF _LE D STROBE _PW R 4 +3.1VD ZOOM MOTOR 2 +5VM ZOOM SENSOR +3.1VD LE NS_PS SHUTTE R_M1 SHUTTE R_M0 IN1 IN2 IN3 IN4 6 DG ND F LASH_VP +3.1V D LE NS _P S S HUT T E R_M1 S HUT T E R_M0 IN1 IN2 IN3 IN4 LE NS_PS SHUTTE R_M1 SHUTTE R_M0 IN1 IN2 IN3 IN4 3 F LA S H_V P BUZZER Q2 F LA S H +3.1V D MEMORY STICK LE NS 2 GREEN +5V M 33.75MHZ +13.4V CAPACITOR 100UF 300V SELF TIMER LED 1 1 DGND +3.1VD MS_ON R/B MS_INS# C LE WE WP ALE CE0 RE MS_C LK MD[0..7] F A23 F A20 F A22 F A21 1 F LA S H_RDY 4 DG ND +3.1V D 4 S T RO B E _C HG S T RO B E _T rg RA MD[0..15] RA MA [0..14] RA MLDM RA MW E _N RA MC A S RA MRA S RA MC S _N RA MLDQ S RA MUDQ S RA MUDM RA MC LK _N RA MC LK RA MC LK _E N RA MRE F 2 ME MO RY SHUT1 SHUT2 PW _LE D PW R_KE Y 3 DG ND S HUT 1 S HUT 2 P W _LE D P W R_K E Y SHUT1 SHUT2 PW _LE D PW R_KE Y +3.1VD IRIS(METER) LC D TOP +3.1V D LENS +13.4V +13.4V +3.1V D 3 2 DS P 1 Out P owe r 4 POWE R GND_3 3 2 GND_2 MIC 1 S P M0204HD5 Q29 AO3415 3 MC4_4.72X3.76_173 G2412-0039-00 1 BATT+2 3 2 1 2 1 F3 1.6A/32V 1 -7.5V VP -7.5V 1 C186 FLASH_VP 2 R163 100K 2 C160 1 1 1 0 .1 U K _ 1 6 V _ X 5 R R131 100K 2 0 .1 U K _ 1 6 V _ X 5 R 2 2 1 1 2 C159 2 BATT-2 1000P K _25V _X7R C187 10 00P K _25V _X 7R 2 F5 1A/24V Q42 AO3415 DSC-S730 3-1 4. REPAIR PARTS LIST 4-1. EXPLODED VIEWS 4-1-1. OVERALL SECTION ns: not supplied 3 15 4 6 13 16 18 2 19 11 5 10 (Note) 12 17 7 ns 14 15 9 Main Frame Block (See Page 4-2) 1 8 Note : The adjustment is not required after replacing the LCD • Refer to cover for mark Ref. No. . Part No. Description 1 2 3 4 5 X-2188-411-1 X-2188-412-1 3-286-696-01 3-286-697-01 3-286-698-01 CABINET (FRONT) ASSY CABINET (REAR) ASSY SHAFT, STRAP BLOCK, RL LCD 6 7 8 9 10 A-1444-049-A 3-286-700-01 3-286-701-01 3-286-702-01 3-286-703-01 ST BLOCK ASSY SHAFT, BT LID LID, BT SPRING, BT LID LID, JACK Ref. No. DSC-S730 4-1 Part No. Description 11 12 13 14 15 3-287-023-11 3-287-026-01 3-287-028-01 3-287-027-01 3-287-025-01 SCREW M1.7 X 2.7 SCREW TP1.4 X 2.5 SCREW TP1.7 X 3.5 SCREW TP1.7 X 4 SCREW TP1.4 X 3 16 17 18 19 3-287-032-01 3-296-920-01 3-296-921-01 3-299-366-01 SCREW TP1.7 X 6.5 SCREW TP1.4 X 3.5 SCREW TP1.4 X 4 SCREW TP1.7 X 3.5 4. REPAIR PARTS LIST 4-1-2. MAIN FRAME BLOCK ns: not supplied ns (Note 1) 104 104 102 102 103 ns 101 ns (Note 1) 105 (Note 2) Note 1 : In case of the lens block assy or main board failure, contact your local Sony service Headquarter for the measures. Note 2 : When separate lens block assy and main board for main frame replacement, assemble original lens block assy and main board back after repaire. Ref. No. 101 102 103 104 105 Part No. Description 3-286-699-01 3-287-024-01 3-287-026-01 3-287-028-01 3-286-704-01 SUPPORT (JACK) SCREW TP1.4 X 3 SCREW TP1.4 X 2.5 SCREW TP1.7 X 3.5 FRAME, MAIN DSC-S730 4-2 4. REPAIR PARTS LIST 4-2. ACCESSORIES Checking supplied accessories. Note 1: This item is supplied with the unit as an accessory, but is not prepared as a service part. A/V cable 3-196-980-01 USB cable 3-196-981-01 Wrist strap 2-050-981-01 Instruction Manual 3-281-198-11 3-281-198-21 3-281-198-31 3-281-198-41 3-281-198-51 3-281-198-61 3-281-198-71 3-281-198-81 3-281-198-91 3-281-199-11 3-281-199-21 3-281-199-31 3-281-199-41 3-281-199-51 3-281-199-61 3-281-199-71 (ENGLISH) (CND, AEP, UK, E, AUS, HK, JE) (FRENCH, ITALIAN) (CND, AEP) (SPANISH, PORTUGUESE) (AEP, E, JE) (GERMAN, DUTCH) (AEP) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, JE) (RUSSIAN, UKRAINIAN) (AEP) (ARABIC, PERSIAN) (E) (KOREAN) (KR, JE) (POLISH, CZECH) (AEP) (HUNGARIAN, SLOVAK) (AEP) (SWEDISH, FINNISH) (AEP) (NORWEGIAN, DANISH)(AEP) (THAI, MALAYSIAN) (E) (TURKISH, GREEK) (AEP) (ENGLISH, SPANISH) (US) (SIMPLIFIED CHINESE) (CH) LR6 (size AA) Alkaline Battery (Note 1) Cyber-shot Handbook(PDF) The CD-ROM supplied contains all of language version of the Instruction Manual in pdf (Cyber-shot Handbook.pdf) for printing. The printed matter is not supplied. If required, please order it with the part number below. CD-ROM (Cyber-shot application software/ "Cyber-shot Handbook"/ "Cyber-shot Step-up Guide") *3-281-189-01 * * * * * * * * * * * * * 3-281-190-11 3-281-190-21 3-281-190-31 3-281-190-41 3-281-190-51 3-281-190-61 3-281-190-71 3-281-190-81 3-281-190-91 3-281-191-11 3-281-191-21 3-281-191-31 3-281-191-41 (ENGLISH) (FRENCH) (ITALIAN) (SPANISH) (PORTUGUESE) (GERMAN) (DUTCH) (TRADITIONAL CHINESE) (SIMPLIFIED CHINESE) (RUSSIAN) (ARABIC) (PERSIAN) (KOREAN) NOTE: Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Abbreviation AUS : Australian model CH : Chinese model CND : Canadian model HK : Hong Kong model JE : Tourist model KR : Korea model DSC-S730 4-3 * * * * * * * * * * * * * 3-281-191-51 3-281-191-61 3-281-191-71 3-281-191-81 3-281-191-91 3-281-192-11 3-281-192-21 3-281-192-31 3-281-192-41 3-281-192-51 3-281-192-61 3-281-192-71 3-281-192-81 (POLISH) (CZECH) (HUNGARIAN) (SLOVAK) (SWEDISH) (FINNISH) (NORWEGIAN) (DANISH) (THAI) (MALAYSIAN) (TURKISH) (GREEK) (UKRAINIAN) 【Regarding Fuse】 ・MAIN BOARD F5 F3 F5 MANUFACTURER: KAMAYA ELECTRIC CO.,LTD. TYPE: FCC10102AD RATING: 1.0A F3 MANUFACTURER: KAMAYA ELECTRIC CO.,LTD. TYPE: FCC16162AD RATING: 1.6A DSC-S730 Reverse 985223911.pdf Revision History Ver. Date 1.0 2007.11 DSC-S730 History Official Release Contents — S.M. Rev. issued —