Download PCM-R300

PCM-R300
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
Ver 1.1 2001. 06
Model Name Using Similar Mechanism
DTC-A6
Tape Transport Mechanism Type
DATM-110A
SPECIFICATIONS
– Continued on next page –
DIGITAL AUDIO RECORDER
9-922-708-12
Sony Corporation
2001F0200-1
© 2001.6
Home Audio Company
Shinagawa Tec Service Manual Production Group
–1–
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
MODEL IDENTIFICATION
— Back Panel —
Parts No.
3-018-941-0π : US, Canadian model
3-018-941-1π : AEP, UK model
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS
SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
–2–
SAFETY CHECK-OUT
TABLE OF CONTENTS
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
1. SERVICING NOTE ........................................................... 4
LEAKAGE
The AC leakage from any exposed metal part to earth Ground and
from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM
that is suitable. Nearly all battery operated digital multimeters
that have a 2V AC range are suitable. (See Fig. A)
3-1.
3-2.
3-3.
3-4.
3-5.
To Exposed Metal
Parts on Set
0.15µF
1.5kΩ
AC
voltmeter
(0.75V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
2. GENERAL .......................................................................... 5
3. DISASSEMBLY
Case ..................................................................................... 14
Cassette Window ................................................................. 14
Mechanism Deck ................................................................ 14
Cassette Holder Assembly .................................................. 14
Cassette Compartment Motor (M901), Pulley,
Driving Gear and Slider ...................................................... 15
3-6. Drum Drive Board and Driving Chassis ............................. 15
3-7. Drum ................................................................................... 16
3-8. Capstan Motor (M902) ....................................................... 16
4. ADJUSTMENTS ............................................................ 17
5. DIAGRAMS
5-1. Circuit Boards Location ..................................................... 21
5-2. Block Diagrams
• MD Section ...................................................................... 22
• Main Section .................................................................... 23
• Display/Power Section ..................................................... 25
5-3. Schematic Diagram — MD Section — .............................. 26
5-4. Printed Wiring Board — MD Section — ........................... 29
5-5. Printed Wiring Board — Main Section — ......................... 32
5-6. Schematic Diagram — Main Section (1/3) — ................... 35
5-7. Schematic Diagram — Main Section (2/3) — ................... 38
5-8. Schematic Diagram — Main Section (3/3) — ................... 41
5-9. Printed Wiring Board — Dispaly Section — ..................... 44
5-10. Schematic Diagram — Display Section — ...................... 47
5-11. IC Block Diagrams ........................................................... 49
5-12. IC Pin Functions ............................................................... 53
6. EXPLODED VIEWS
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
6-7.
6-8.
Case and Back Panel Section .............................................. 59
Front panel Section ............................................................. 60
Chassis Section ................................................................... 61
Cassette Compartment Section ........................................... 62
Chassis L/R Section ............................................................ 63
Mechanism Section-1 (DATM-110A) ................................ 64
Mechanism Section-2 (DATM-110A) ................................ 65
Mechanism Section-3 (DATM-110A) ................................ 66
7. ELECTRICAL PARTS LIST ........................................ 67
–3–
SECTION 1
SERVICING NOTE
Fluorescent indicator tube lit, key check mode
• Part Location
The Fluorescent indicator tubes and keys can be checked in this test
mode.
[DISPLAY BOARD] (Conductor side)
Settings: INPUT switch
: Center click
ID MODE switch : Center click
REC MODE switch : Center click
TP (TEST)
IC801
NOTE:The method differs for when the remote commander provided
is used or not.
Method:
1. Disconnect the AC plug from the outlet, and short-circuit the TP
(TEST) of the display board and ground.
2. Connect the AC plug to the outlet, and turn on the power to start
the check.
Test mode
Flow:
The left and right segments of the Fluorescent indicator tubes and
level meters light up, and the grids light up in order from the right
side.
The level meters go off one by one.
Operate the remote commander for DAT in this state.
(If the remote commander
is used)
Pressing the 6button will
display “NEXT KEY” and
set the key check mode.
(If the remote commander
is not used)
(If the remote commander
is used)
Pressing the 4 button
will turn off the segments
on the left and right sides.
Press the pSTOP button.
“NEXT RMC” will be displayed.
Press the ”PLAY button for more than
1 second, and then press the PPAUSE
button.
“NEXT KEY” will be displayed and the
key check mode will be set.
Pressing a button on the panel or switching a switch will light up the
level meters one by one.
When all buttons and switches have been operated, all the level meters
will be lit and “KEY OK” will be displayed instantaneously.
“TEST END” is displayed and the test mode is ended.
• To reset the test mode, turn the power off and disconnect the wire
shorting TP (TEST) and ground.
–4–
Pressing the 7button will
display “TEST END” and
end the test mode.
(If the remote commander
is not used)
To end the test mode,
disconnect the AC plug
from the outlet.
SECTION 2
GENERAL
Location of Parts and Controls
Front panel
1
27
26
25
2
24 23
3
4
5
6
22 21 20
7
8
9
19
18
10 11
17
Remote commander (RM-D757)
19
28
32
29
30
31
21
20
23
25
24
2
22
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
–5–
Display window
0/) (REW/FF), DATA buttons
MODE, MENU button
RESET, ENTER button
Cassette holder
Remote sensor
MARGIN RESET button
WRITE button
START ID AUTO button
START ID RENUMBER button
START ID REHEARSAL button
ERASE button
REC LEVEL control
PHONE LEVEL control
PHONES jack
SBM switch
REC MODE switch
ID MODE switch
6 OPEN / CLOSE button
r REC button
R REC MUTE button
P PAUSE button
( PLAY button
=/+ AMS, SELECT buttons
p STOP button
POWER button
INPUT switch
COUNTER MODE button
COUNTER RESET button
Numeric buttons
CLEAR button
REPEAT button
16
12
13
15
14
This section is extracted from
instruction manual.
–6–
–7–
–8–
–9–
– 10 –
– 11 –
– 12 –
– 13 –
SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
3-1. CASE
3-2. CASSETTE WINDOW
Unscrew the four case attachment screws and remove the
case.
1 Press the OPEN/CLOSE switch to effect LOADING OUT
STATE (if power is not supplied) rotate the pulley in the
left side of the Mechanism Deck counterclockwise.)
2 Remove the cassette by lifting the window up.
3-3. MECHANISM DECK
1 Four screws
(PTTWH3x6)
2 Connector (CN1)
3 Connector (CN302)
6 Mechanism deck
4 Connector (CN341)
5 Connector (CN301)
3-4. CASSETTE HOLDER ASSSEMBLY
2 Cassette holder assembly
1 Screw (Step)
5 Holder (Window)
4 Spring (Cassette)
3 Screw
(BVTP3x6)
– 14 –
3-5. CASSETTE COMPARTMENT MOTOR (M901), PULLEY, DRIVING GEAR AND SLIDER
9 Cassette compartment motor
(M901)
8 Two screws
(P2.6x3)
7 Slider
6 Two screws
(BTP1.7x3)
1 Belt (Driving)
2 Screw
(BTP1.7x3)
5 Driving gear
3 Pulley
4 Screw
(BTP1.7x3)
3-6. DRUM DRIVE BOARD AND DRIVING CHASSIS
3 Remove the lead wires
from connectors on the
drum drive board.
2 Two screw
(B2.6x4)
1 Screw
(BTP2.6x6)
4 Drum drive board
5 Two screw
(BTP2.6x8)
6 Screw
(BTP2.6x8)
8 Driving chassis
7 Screw
(B2.6x4)
– 15 –
3-7. DRUM
2 Four screws
(B2x4)
4 Remove the drum lead
wires from connectors.
3 Shield case
5 Drum
1 Lever (Cleaner) assembly
3-8. CAPSTAN MOTOR (M902)
1 Three screws
(P1.7x4)
2 Capstan motor
(M902)
– 16 –
SECTION 4
ADJUSTMENTS
5. Cleaning of the Revolving Drum
(1) Fold a cleaning piece (2-034-697-00) or a knit cloth into 4 or
more files, slightly impregnate it with a head cleaning fluid (9919-573-00), and softly touch the drum with it and manually
rotate the drum slowly counterclockwise by 2 to 3 turns for
cleaning.
(2) At that time, be careful not to move the cleaning piece vertically
to the head tip. Otherwise, the head tip may probably be
damaged.
4-1. Notes When Making Adjustments
1. Adjustments should be performed in the order listed.
2. Use the following test tapes:
TY-7111X (8-909-823-00) ............................... Level
TY-7252 (8-909-822-00) .................................. Tracking
TY-7551 (8-909-814-00) .................................. Functions
TY-30B (8-892-358-00) ................................... Blank
Use the following torque meter:
TW-7131 (8-909-708-71) ................................ FWD
6. Be careful not to move RV1 to RV2 on the RF AMP board in the
mechanism assemlby
3. Switches and controls should be set as follows unless otherwise
specified.
ID MODE switch
: START
REC MODE switch
: LONG
INPUT switch
: OPT
SBM switch
: OFF
REC LEVEL control
: Min.
PHONE LEVEL control : Min.
4. Creating an end sensor cassette
(1) Press the tape slider lock and move the slider in the direction
indicated by the arrow.
7. To adjust the tape path and guides, remove the holder assembly as
shown in the diagram and use the DAT cassette holder jig (J-8000002-A). This will make it easier to perform the adjustments.
• First turning the pulley counterclockwise to put it in loading out
status will make removal and reattachment of the holder assembly
easier.
• To perform adjustments, turn the pulley clockwise to put it in loading
in status, load the cassette tape and set the IN switch to the ON
position.
Hub hole
Slider lock
Holder
Slider
Step screw
Holder
(window)
Hub hole
Slider lock
Spring
(cassette)
(2) Open the lid and cut the tape.
Screw
(BVTP3x6)
8. Test mode
To set the test mode, short-circuit JW091 (X TEST) and ground
of the main board. (At this time, the dB display of the fluorescent
display level meter will blink.)
Lid
Cut here.
Slider
Tape
(3) Turn the hubs until the tape is completely inside the cassette
(both T and S sides).
The end sensor cassette for end sensor adjustments is now ready
for use.
– 17 –
Perform the following adjustments in the test mode.
• FWD torque adjustment
• FWD back tension check
• Tape path fine adjustments
• DPG adjustment
• AGC voltage check
• End sensor check
• To reset the test mode (main), disconnect the wire shorting JW091
(X TEST) and ground. After completion of adjusting, be sure to
reset the test mode (main).
9. Check the following items for correct tape speed, after completion
of adjusting.
(1)Set the REC MODE switch to 48k and check for normal recording
and playback. (x1)
(2)Set the REC MODE switch to LONG and check for normal
recording and playback. (x0.5)
(3)With QUE (”+)) or REVIEW (”+0), check that qurrr, qurrr
sound is heard. (x3, x8)
(4)Check that correct time is displayed after FF ()) or REV (0).
(x16)
(5)Check that AMS (+, =) is normal.
4-2. ELECTRICAL ADJUSTMENTS
FWD Torque Adjustment
Procedure:
1. Set the test mode (main) and load the FWD torque meter TW7131 (8-909-708-71) .
2. Set the PLAY (() mode.“TORQUE” will be displayed on the
fluorescent indicator tube.
3. Adjust RV451 so that the minimum value of FWD take up torque
(take-up side rewinding torque) is between 9-10g • cm (0.13-0.14
oz • inch).
Also, make sure that the maximum reading does not exceed 15g •
cm (does not exceed 0.21 oz • inch).
4. Confirm that the value indicated by the torque meter is maintained
for one full cycle.
FWD Back Tension Check and Adjustment
Check procedure:
1. Put the set into the test mode (main • servo) and load the FWD
torque meter TW-7131 (8-909-708-71).
2. Put the set into the PLAY (() mode.
3. Turn the FWD back tension adjustment screw locked on the
mechanical deck side so that the minimum value of FWD back
tension torque (supply side) is between 4.5 to 7.5g • cm- (0.060.1 oz • inch).
Also, make sure that the maximum reading does not exceed 8g •
cm (does not exceed 0.11 oz • inch).
After completion of adjusting, be sure to apply screw lock.
4. Confirm that value indicated by the torque meter is maintained
for one full cycle.
5. If the specified values are not satisfied, replace the lever (BT)
assembly (X-3363-024-1).
FWD back tension
adjustment screw
(+P2x2.5)
To tighten (clockwise) - back tension becomes larger.
to loosen (counterclockwise)-back tension becomes smaller.
Tape Path Fine Adjustment (x1.5 FWD Mode)
Perform the following adjustment when the drum has been replaced.
Procedure:
1. Connect an oscilloscope CH-1 to JW183 (PBRF) and CH-2 to
JW092 (SWP) on the main board.
2. Set the test mode (main) and load test tape TY-7252 (8-909-82200).
3. Press the AMS (+) key. “DPG” will be displayed on the
fluorescent indicator tube.
Each part of switches on Test Mode.
REC MODE
STANDARD
OFFSET
–
ANALOG
0
OPT
+
COAXIAL
INPUT
– 18 –
48 kHz
44.1 kHz
LONG
OFF
AFT
ON
4. With the REC MODE switch set to 48kHz (ATF: OFF) and the
INPUT switch set to COAXIAL or ANALOG (OFFSET: + or –),
fine adjust the S1 and T1 guides so that the oscilloscope RF signal
waveform remains the same when high-low is repeated.
* Finish the adjustment by screwing in.
5. Check the RF signal waveform with the REC MODE switch set
to LONG (ATF: ON) and the INPUT switch set to COAXIAL or
ANALOG (OFFSET: + or–).
OK
DPG Adjustment
Perform the following adjustment without fail when the drum has
been replaced.
End Sensor Check
Perform the following adjustment when the holder has been removed
or part of the mechanism deck section replaced.
Procedure:
1. Connect oscilloscope CH-1 to JW183 (PBRF) and CH-2 to JW092
(SWP) on the main board. (Use CH-2 as the trigger.When the
CH-2 signal is inverted, the trailing edge can be used for
synchronization.)
2. Set the test mode (main) and load test tape TY-7252 (8-909-82200).
3. Set the REC MODE switch to LONG (ATF: ON) and the INPUT
switch to OPT (OFFSET:0).
4. Press the AMS (+) key. “DPG” will be displayed on the
fluorescent indicator tube.
5. Press the 0 and ) keys as appropriate so that the gap between
the oscilloscope SWP and RF signals become 650 ± 15µsec.
(Hold the 0 and ) keys down for more than 1 second to
perform rough adjustment. Hold them down for approximately
0.2 seconds for fine adjustment, and the auto adjustment can be
performed pressing PLAY (() key).
Procedure:
1. Connect an oscilloscope to the JW158 (SEND: in the S side) and
JW143 (TEND: in the T side) of the main board.
2. Set the test mode (main), mount an end sensor cassette and effect
the STOP (p) mode.
3. Check that p-p values of waveform of the oscilloscope satisfy the
following.
in the S side: 300 mVp-p or more
in the T side: 150 mVp-p or more
Adjustment Location:
– Mechanism assembly –
T1 guide
4/5 A or less
RF (PBRF)
NG
A
4/5 A' or less
SWP
650 ± 15 µsec
T2 guide
NG A'
6. Check the RF signalwaveform with the REC MODE switch set to
LONG (ATF: ON) and the INPUT switch set to OPT (OFFSET:
0).
(1) Confirm that the RF signal waveform peak value (B) is 60mV or
more.
(2) Confirm that the undershoot level of the RF signal waveform's
flat portion is within 10%.
B/10 or less
B/10 or less
AGC Voltage Check
Perform this adjustment after cleaning the heads with a cleaning
cassette.
S1 guide
Procedure:
1. Connect oscilloscope CH-1 to JW247 (GCA: Gain Control Amp.)
and CH-2 to JW092 (SWP) on the main board. (When the CH-2
signal is inverted, the trailing edge can be used for
synchronization.)
2. Set the test mode (main) and load test tape TY-7111X (8-909823-00).
3. Set the PLAY (() mode and check that the GCA waveform on
the oscilloscope is as follows
S2 guide
F guide
[MAIN BOARD] (Component side)
Tape Path Fine, DPG,
AGC Voltage
Test mode (Main)
1V
B
JW091
(X TEST)
0V
IC310
(When the output level or B ch is low)*
7. When the measured values are not within the above tolerance repeat
items 3 to 6 above.
JW092
(SWP)
GCA
1V
JW143
(TEND)
Adjustment Point: Mechanism assembly
JW158
(SEND)
0V
(When the output level or A ch is low)*
End Sensor
Tape Path Fine,
DPG
IC304
CN302
CN341
JW183
(PBRF)
JW247
(GCA)
SWP
AGC Voltage
A ch
B ch
* Slightly changes depending on the state of the head. NG if the GCA
waveform is 1V or more or equal to the ground level.
– 19 –
RV451
A ch
FWD Torque
– 20 –
PCM-R300
SECTION 5
DIAGRAMS
5-2. BLOCK DIAGRAMS
— MD SECTION —
5-1. CIRCUIT BOARDS LOCATION
INLET board
IL COVER board
CASSETTE COMPARTMENT/
CAM MOTOR DRIVER
IC421
PRIMARY board
M901
CASSETTE
COMPARTMENT
MOTOR
COAX I/O board
CM+
3
6
15 CM-IN
C-PWM 84
M
CM– 5
2
16 CM-OUT
CAP-RVS
M903
CAM
MOTOR
CAM1
M
M902
CAPSTAN MOTOR
ASSY
MAIN-MECHA CONTROL
IC310(2/2)
CAM2
10
12
9
18 LM-LD
13
17 LM-EJ
CAPSTAN MOTOR
DRIVER
IC441(2/2),Q441
CAPSTAN MOTOR
PWM BUFFER
IC441(1/2)
CERR
M
C DIR
2
CFG 69
12
CAPSTAN FG
AMP
IC01(1/2)
14
13
OUT B
OUT A
FG
AC SW board
MAIN board
+5V
S1
CASSETTE
LOCK
S2
CASSETTE
OUT
SW COVER board
DISPLAY board
27 CAS LCK
28 CAS OUT
S02
THIN DET
SBM DF board
HEADPHONE board
SW1 STOP DET
30 RE-STOP
SW2 FWD DET
29 RE-FWD
S01–1 REC PROOF
26 REC-EN
S01–2 CASSETTE IN
25 CAS-IN
REEL MOTOR board
PM904
TENSION
PLUNGER
TENSION PLUNGER
PWM BUFFER DRIVE
IC451(1/2),Q481
TFG 67
7
BRAKE PLUNGER
DRIVER
Q411–414
RF AMP board
1
3 PLN-ON
4 PLN-KICK
DRM-ON
DRUM MOTOR
PWM BUFFER
IC431(1/2)
D01
VS
D ON
DPG 71
9 DRUM PG AMP 6
60 S-END
DFG 70
10 DRUM FG AMP 1
59 T-END
+5V
PH04
TOP END SENSOR
(SUPPLY SIDE)
5
46 LED-ON
PH03
TOP END SENSOR
(TAKE UP SIDE)
CAM SLIDER board
RGN SW board
– 21 –
M900
DRUM ASSY (1/2)
(MOTOR)
5
09
THIN board
SUPPLY
REEL FG SENSOR
PH02
M
IC01(2/2)
END SENSOR
LED DRIVER
Q351
T/E SENSOR board
2
DRUM MOTOR
DRIVER
IC02,Q01,02
DRUM COM
DRUM DRIVE board
TAKE-UP
REEL FG SENSOR
PH01
REEL FG
AMP
IC03
D-PWM 83
PM903
BRAKE
PLUNGER
M905
REEL
MOTOR
6
82 T-PWM
DRUM assembly
CASSETTE COMPARTMENT
SW board
M
RV451
FWD TORQUE
SFG 68
CASSETTE COMPARTMENT
MOTER board
REEL MOTOR
DRIVER
Q451,458,459
REEL MOTOR
DIRECTION SWITCH
Q452–457
R-CW 1
R-CCW 100
REMOCON board
CAM SLIDER
SWITCH
REEL MOTOR
PWM BUFFER
IC451(2/2)
24 THIN
+5V
REC VOL board
R-PWM 81
– 22 –
COM
PG
FG
FG
SPLM
DFVDD1
DVDDR
VSUB(D)R
VSUB(C)R
VDD2
VDD
R1(–)
VSS
R1(+)
VSS2
32 31
30 29 28 27 26 25 24 23 22 21 20
XSEL
201x16
IC653 CXD8505BQ
SYSM 33
ATT
SHIFT
LATCH
XINT
34
35
36
37
XDCK
XLRCK
DATA1
VSUD(D)R
DF VSS
VSUB(D)L
INAF
38
39
40
41
42
43
44
"O" DETECT
MUTE
CIRCUIT
MODE
PLM
ATT
S/P
FIR2
FIR3
L. I. P.
(x 8)
3RD ORDER
NOISE
SHAPER
IIR
CLOCK
GENERATOR
AC, DC
DITHER
ATT
FIR1
FIR2
FIR3
L. I. P.
(x 8)
3RD ORDER
NOISE
SHAPER
IIR
45
46
47
48
49
50
51
PLM
TIMING
CIRCUIT
61 62 63 64
IC903 M5230L-A
L1(–)
VSS
L1(+)
MUTE L
TEST 1
TEST 2
DFVDD2
DV DDL
VSUB(D)L
VSUB(C)L
VDD2
VDD
52 53 54 55 56 57 58 59 60
VSS2
R2(+)
VSS
R2(–)
VDD
VDD2
VSUB(A)R
XVSS
XVSS
X IN
X OUT
XVDD
VSUB(A)L
VDD2
VDD
L2(–)
VSS
L2(+)
VSS2
VSS2
512FS0
256FS0
128FS0
I NV1
I NV01
I NV02
MUTE R
FIR1
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
IC999 AT24C01A-10SC-TP-B
GND 1
BALANCE ADJ 2
NC 1
ERROR
AMP
8 VCC
DOUT
LOGIC
DOUT/ACK
R/W
DIN
NC 2
OUT(–) 3
7 TEST
SERIAL MUX
OVER CURRENT
PROTECTION
CIRCUIT
VOLTAGE ADJ 5
ERROR
AMP
OUT(+) 6
OVER CURRENT
PROTECTION
CIRCUIT
X DEC
EEPROM
IN(–) 4
Y DEC
ADDRESS/COUNTER
DATA WORD
NC 3
DATA REGISTER
REFERENCE
VOLTAGE
CIRCUIT
H.V.PUMP/TIMING
GND 4
OVER HEAT
PROTECTION
CIRCUIT
START
CIRCUIT
IN(+) 7
OUT CONTROL 8
– 51 –
INC
EN
6 SCL
LOAD
LOGIC
CONTROL
SERIAL
LOGIC
STOP
START
5 SDA
• DISPLAY Section
IC802 MSM6338RS
16 VDD
15 A1
14 A2
BCK 2
0dB
OVER
DETECTION
CIRCUIT
0dB OVER
COUNTER
0dB OVER
COUNTER
0dB
OVER
LATCH
L.R
RD
(BI-DIRECTION)
16BIT S.R
WR
DATA 1
CS
READ
WRITE
LOGIC
LRCK 3
ABSOLUTE
CIRCUIT
RESET 4
WR 5
RD 6
CS 7
15BIT LATCH
WR
RD
CS
A
COMP
B
A≥B
CONTROL
&
OVER
REG
CONTROL
CIRCUIT
MAX
REG
(L-CH)
15BIT
LATCH
OUT
REG
16BIT
LATCH
MPX
MAX
REG
(R-CH)
15BIT
LATCH
VSS 8
– 52 –
13 DB3
12 DB2
DATA
BUS
BUFFER
11 DB1
10 NC
9 DB0
5-12. IC PIN FUNCTIONS
• IC304 Digital Signal Processor (CXD2605Q)
Pin No
1, 2
3
4 to 8
Pin Name
I/O
Function
A8, A9
O
External RAM address output
VDD
—
Power supply (+5V)
A10 to A14
O
External RAM address output
9
XWE
O
External RAM write enable signal output
10
XCE
O
External RAM output enable signal output
11
XEAN
O
Not used
12
TST1
I
Test pin (Fixed at “L”)
13
XT1O
O
Crystal oscillation circuit 1 output (18 MHz)
14
XT1I
I
Crystal oscillation circuit 1 input (18 MHz)
15
VSS
—
16
XRST
I
Reset input “L”: Reset
17
CLKO
O
Not used
18
MINT
O
19
ATSY
I
ATF sync signal input
20
MCLK
O
Not used
21
DREF
O
SBSY period, duty 50 signal output
22
SBPM
O
Not used
23
EXCK
I
Data transfer clock input from main, mecha control
24
SDSI
I
Serial data input from main, mecha control
25
SDSO
O
Serial data output to main, mecha control
26
SBSY
O
Frame sync signal output for transferring data to main, mecha control
27
PLRF
O
Not used
28
CCLK
O
Not used
29
MUTE
I
Mute input “H”: Mute Not mute REC monitor sound
30
MUTM
O
Mute monitor “H”: Indicates muting occurs
31
UNLK
O
RX-PLL lock monitor signal output “L”: Indicates locking occurs
32
RFCT
I
Playback RF signal control (“L”: Valid, “H”: Invalid) (Fixed at “L”)
33
SYMN
O
Outputs monitor signal for C1 check results corresponding to RF
34
SELB
I
Test pin (Fixed at “H”)
35
PLCK
O
Not used
36
TST2
I
Test pin (Fixed at “L”)
37
RFDT
I
Playback RF signal input
38
XCS
I
Chip select input for data transfer with microprocessor
39
SWP
I
RF switching pulse
40
VSS
—
Ground
41
PIPC
O
ATF pilot signal/discrimination signal output for record signal “H”: Pilot signal
42
REPB
O
REC/PB discrimination signal output “H”: REC
43
REDT
O
Record signal output
44
TST4
I
Test pin (Fixed at “L”)
45
PDO
O
RX-PLL phase comparator output
Ground
Control byte (1) bit 1=“L”: Q code decode (Detecting between songs) output, “H”: BCK
clock output by RX-PLL
“L”: Transfer enable (Fixed at “L”)
“L”: A track, “H”: B track
• Abbreviation
PLL: Phase Locked Loop
– 53 –
Pin No
Pin Name
Function
I/O
46
SELC
I
Oscillation frequency select signal input (Fixed at “L”)
47
MUTA
I
Mute input
48
PLCO
I
RX-PLL external VCO clock input (512 fs as reference)
49
PLVR
O
Not used
50
PLRF
O
Not used
51
MSSL
I
Master mode/slave mode select
52
RX
I
Digital interface signal input
53
VDD
—
Power supply (+5V)
54
TX
O
Digital interface signal output
55
SELA
I
Test pin (Fixed at “H”)
56
EXSY
I/O
57
EXSN
I/O
58
F128
I/O
59
F256
O
60
F512
O
61
ADLF
I
62
DALF
I
DADT, DADO serial data LSB/MSB first select input
63
XT2O
O
Crystal oscillation circuit 2 output (22 MHz)
64
XT2I
I
Crystal oscillation circuit 2 input (22 MHz)
65
VSS
—
Ground
66
XT3O
O
Crystal oscillation circuit 3 output (24 MHz)
67
XT3I
I
Crystal oscillation circuit 3 input (24 MHz)
68
FSEN
I
F128, BCK, LRCK input/output select input
69
LR03
O
Inverted signal of LRCK 16 BCK delay output (Not used)
70
LR02
O
71
LR01
O
72
LRCK
I/O
73
WCK
O
Not used
74
XBCK
O
Outputs inverted signal of BCK
75
BCK
76
ADDT
I
A/D serial data input
77
DADT
O
D/A serial data output
78
DADO
I
Audio data input for digital OUT
79
ADDI
O
Digital IN audio data output
80
ADDN
I
Digital IN audio data input
81
ERRI
I
Validity flag data input for digital OUT
82
ERRF
O
DADT data compensation data/discrimination signal output “H”: Compensation data
83
MUTG
O
Not used
84
D7
I/O
External RAM data input/output (MSB)
D6 to D2
I/O
External RAM data input/output
90
VSS
—
Ground
91
D1
I/O
External RAM data input/output
92
D0
I/O
External RAM data input/output (LSB)
85 to 89
93 to 100
A0 to A7
“H”: Mute. Also mutes REC monitor sound
“H”: Master (Fixed at “H”)
External sync signal input/output
Not used
ADTT, ADDI, ADDN serial data LSB/MSB first select input
I/O
O
“H”: LSB first
(Fixed at “L”)
“H”: LSB first (Fixed at “L”)
“H”: Output (Fixed at “H”)
Not used
fs/2 fs (At 2 X speed) signal input/output
64 fs/128 fs (At 2 X speed) signal input/output
External RAM address output
– 54 –
• IC310 Main, Mecha Control (CXP87540-042Q)
Pin No
Pin Name
Function
I/O
1
R-CW
O
Reel motor CW output “H”: FWD direction
2
CAP-RVS
O
Capstan direction control output “L”: FWD, “H”: RVS
3
PLN-ON
O
Brake plunger ON control output
4
PLN-KICK
O
Brake plunger kick control output
5
DRM-ON
O
Drum motor ON control output
6
—
O
Not used
7
DF-DT
O
Communication line (Serial data) with Digital filter
8
DF-CLK
O
Communication line (Shift clock) with Digital filter
“L”: shifted, “H”: taken
9
VCOEN
O
VCO enable output
10
OPT/COA
O
Digital input switch output “H”: coaxial, “L”: optical
11
ADLD
O
Load to Digital filter for A/D converter
12
DALD
O
Load to Digital filter for D/A converter
13
—
—
14
—
—
15
CM-IN
O
Cassette compartment motor rotation IN direction control output
16
CM-OUT
O
Cassette compartment motor rotation OUT direction control output
17
LM-EJ
O
Loading motor rotation Eject direction control output
18
LM-LD
O
Loading motor rotation Loading direction control output
19
ROM-DT
O
Data output to EEP ROM
20
—
—
21
—
—
22
—
—
23
H-FIX
I
Not used (Fixed at “H”)
24
THIN
I
Detect kinds of tapes
“H”: Active
Not used
Not used
“H”: normal tape, “L”: Thin tape
25
CAS-IN
I
Cassette IN switch input
26
REC-EN
I
REC enable switch input
27
CAS LCK
I
Cassette compartment lock switch input
28
CAS OUT
I
Cassette compartment out switch input
29
RE-FWD
I
Encoder SW2 input
30
RE-STOP
I
Encoder SW1 input
31
—
—
Not used (Open)
32
—
O
Not used
33
SBM
O
Super bit maping control output
34
—
O
Not used
AF3 to AF0
I
AF mode select
35 to 38
39
MP
40
X RST
—
I
SW1
L
H
L
H
Not used (Connected to Ground)
System reset input
“L”: Active
– 55 –
SW2
L
L
H
H
Position
EJECT
STOP
FWD
STOP–FWD
“H”: SBM ON, “L”: SBM OFF
Pin No
Pin Name
Function
I/O
VSS
—
Ground
XTAL
O
System clock output (Open)
43
EXTAL
I
System clock input (9.408MHz)
44
DISP-REQ
O
Communication request output to display control
45
REC-DIS
O
Record current control output “H”: Record disable, “L”: Record enable
46
LED-ON
O
End sensor ON control output
47
ROM-CK
O
Clock output to EEPROM
48
DSP-ACK
I
Communication acknowledge input from display control
49
41
42
“L”: Active
“L”: Active
DSP-DI
I
Serial data input from display control and EEPROM
50
DSP-DO
O
Serial data output to display control and EEPROM
51
DSP-CK
O
Serial clock output to display control and EEPROM
52
SBSY
I
SUB SYNC input from CXD2605Q (master)
53
SDDI
I
Serial data input from CXD2605Q
54
SDDO
O
Serial data output to CXD2605Q
55
SDCK
O
Serial clock output to CXD2605Q (for sub code interface)
56
AVSS
—
Ground for A/D port
57
AVREF
—
Reference voltage for A/D port (+5V)
58
Power supply for A/D port (+5V)
AVDD
—
59
T-END
I
T side end sensor input
60
S-END
I
S side end sensor input
61
L-FIX
I
Fixed at “L”
62
H-FIX
I
Fixed at “H”
63
L-FIX
I
Fixed at “L”
64
MUTM
I
Mute monitor input
65
MINT
I
Q code decode value input “H”: Between songs
66
ATF-IN
I
ATF pilot signal input (Analog input)
67
TFG
I
T side reel FG signal input
68
SFG
I
S side reel FG signal input
69
CFG
I
Capstan FG signal input
70
DFG
I
Drum FG signal input
71
DPG
I
Drum PG signal input
72
DREF
I
Drum reference signal input
73
ATSY-IN
I
DPG auto adjustment FRC signal input
74
R-X5/6V
I
Fixed at “H”
75
MAIN-CHK
O
Not used
76
CAS-TST
I
Test pin
77
MCLK
I
Channel clock input (9.408MHz)
78
“H”: Active
“L”: Test mode with no cassette compartment
PBDT
I
ATF SYNC PB data input
79
SWP
O
Switching pulse output
80
A-PWM
O
PWM signal output for AGC
– 56 –
“L”: Active
Pin No
Pin Name
I/O
Function
81
R-PWM
O
PWM signal output for reel motor
82
T-PWM
O
PWM signal output for tension regulater plunger
83
D-PWM
O
PWM signal output for drum motor drive
84
C-PWM
O
PWM signal output for capstan motor
85
L-FIX
I
Fixed at “L”
86
XTEST
I
Test pin “L”: Test mode (For adjustment)
87
POW-DWN
I
Not used (Fixed at “H”)
88
VSS
—
Ground
89
VDD
—
Power supply (+5V)
90
VPP
—
Connected to +5V
91
ATSY
O
ATF sampling pulse #2 output
92
AREA
O
Not used
93
ADINT
O
A/D converter reset output
94
DAINT
O
D/A digital filter reset output
95
LIN-MUT
O
Line mute output “L”: Active
96
—
—
Not used
97
RLY-MUT
O
Relay mute signal output
98
DIG-MUT
O
Mute signal to CXD2605Q
99
—
—
Not used
100
R-CCW
O
Reel motor CCW output
– 57 –
“L”: Reset
“L”: Reset
“L”: Active
“H”: Active
“L”: RVS direction
• IC801 Display Control (CXP82320-086Q)
Pin No
Pin Name
Function
I/O
1
H
I
Fixed at “H”
2
RMC
I
Remote control signal input
3
TEST
I
Test pin
4
A1 METER
O
5
A2 METER
O
6
M MUT
I
Level meter mute signal input
7
ACK
O
Communication standby complete signal output to main, mecha control
8
SC
I
Serial clock input from main, mecha control
“L”: Test mode (For Fluorescent indicator, key and remote commander check)
Digital peak level meter 4-bit address bus
9
SI
I
Serial data input from main, mecha control
10
SO
O
Serial data output to main, mecha control
11
CS METER
O
Chip select signal output to Digital peak level meter
12
RD METER
O
Read signal output to Digital peak level meter
13
WR METER
O
Write signal output to Digital peak level meter
14 to 21
—
O
Not used
22 to 29
AD0 to AD7
I
Key input
30
XRST
I
System reset input
31
EXTAL
I
System clock input (4.19MHz)
32
XTAL
O
System clock output (4.19MHz)
33
VSS
—
Ground
34 to 57
S0 to S23
O
Fluorescent indicator tube segment drive output
58 to 70
T12 to T0
O
Fluorescent indicator tube grid drive output
71
VFDP
I
–30V power supply for driving fluorescent indicator tube
72
VDD
—
Power supply (+5V)
73
NC
—
Connected to +5V
D0 to D3 METER
I/O
Digital peak level meter 4-bit data bus
74 to 77
“L”: Active
78
H
I
Fixed at “H”
79
REQ
I
Communication request signal input from main, mecha control
80
MODE
I
Fixed at “L”
• IC802 Digital Peak Level Meter (MSM6338RS)
Pin No
Pin Name
Function
I/O
1
DATA
I
fs serial data input (2’s complement)
2
BCK
I
fs serial data fetch clock (Bit clock)
3
LRCK
I
fs input Lch/Rch discrimination signal “H”: Rch, “L”: Lch
4
XRST
I
Reset input “L”: Reset
5
WR
I
Data write request input (Data write at rising edge)
6
RD
I
Data read request input “L”: Read enable
7
CS
I
Chip select input
8
VSS
—
9
D0
I/O/Z
10
NC
—
11
D1
I/O/Z
12
D2
I/O/Z
13
D3
I/O/Z
14
A0
I
15
A1
I
16
VDD
—
“L”: Select
Ground
4-bit data bus (Tristate)
Not used
4-bit data bus (Tristate)
Address input Selects internal register
Power supply (+5V)
O/Z: In case of no output data, it becomes high impedance.
– 58 –
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may have
some difference from the original one.
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
The components identified b y
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
• The mechanical parts with no reference number in
the exploded views are not supplied.
• Hardware (# mark) list and accessories and packing materials are given in the last of this parts list.
• Abbreviation
CND : Canadian model
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
6-1. CASE AND BACK PANEL SECTION
1
4
4
#23
#22
#25
3
FRONT PANEL
#22
6
not supplied
IL001
#24
2
5
7
7
#24
#24
8
Ref. No.
Part No.
Description
* 1
* 2
* 3
4
* 5
3-350-407-41
1-661-402-11
1-661-406-11
3-704-366-21
3-018-941-01
CASE
COAX I/O BOARD
IL COVER BOARD
SCREW (CASE)(M3X10)
PANEL, BACK (US,CND)
Remark
Ref. No.
Part No.
Description
* 5
* 6
7
8
! IL001
3-018-941-11
1-661-405-11
4-956-885-01
3-703-685-21
1-251-234-11
PANEL, BACK (AEP,UK)
INLET BOARD
FOOT (F58175S2W)
SCREW (+BV 3X8)
INLET, AC
– 59 –
Remark
6-2. FRONT PANEL SECTION
60
70
63
S001
not
supplied
66
#19
FL801
64
73
#3
69
67
74
75
72
59
61
58
#4
68
71
51
76
65
62
#3
53
54
55 56
RV101
57
Supplied
with RV101
52
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Ref. No.
Remark
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
Part No.
Description
Ref. No.
Part No.
Description
51
52
53
54
55
4-908-848-31
3-018-940-01
3-382-635-01
3-356-957-01
3-382-634-01
EMBLEM, SONY
PANEL, FRONT
KNOB (REC-R)
SPRING
KNOB (REC-L)
* 66
* 67
* 68
69
70
A-2007-739-A
1-661-399-11
1-661-400-11
4-922-921-21
1-775-464-11
DISPLAY BOARD, COMPLETE
REMOCON BOARD
REC VOL BOARD
BUTTON (POWER)
WIRE (FLAT TYPE)(17 CORE)
56
57
58
59
60
3-382-627-01
3-922-823-21
3-922-822-11
3-922-932-01
3-922-824-21
SPRING, RING
ESCUTCHEON (R)
ESCUTCHEON (L)
WINDOW (FL TUBE)
BUTTON (1)
*
*
*
*
71
72
73
74
75
3-917-216-02
4-932-810-11
4-947-170-01
1-661-403-11
1-661-404-11
KNOB (TIMER)
CUSHION (FL)
HOLDER
AC SW BOARD
SW COVER BOARD
61
62
63
64
65
3-922-825-21
3-922-826-21
3-922-827-21
4-922-518-01
4-969-185-01
BUTTON (2)
BUTTON (3)
BUTTON (4)
KNOB (TIMER)
WINDOW (REMOTE CONTROL)
3-831-441-99
1-517-382-11
1-241-937-11
1-572-267-51
CUSHION, SPEAKER
INDICATOR TUBE, FLUORESCENT
RES, VAR, CARBON 20K/20K
SWITCH, PUSH (AC POWER)(1 KEY)(POWER)
76
FL801
RV101
! S001
– 60 –
Remark
6-3. CHASSIS SECTION
101
#4
111
#4
#4
102
T901
103
108
108
106
107
110
108
Supplied
with J601
104
107
109
MECHANISM DECK
not supplied
105
Supplied
with RV651
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Ref. No.
*
*
*
*
*
Part No.
Description
101
101
102
103
104
A-2007-737-A
A-2007-740-A
1-661-401-11
1-656-335-11
1-656-334-11
MAIN BOARD, COMPLETE (US,CND)
MAIN BOARD, COMPLETE (AEP,UK)
PRIMARY BOARD
SBM DF BOARD
HEADPHONE BOARD
105
106
X-3362-818-1 KNOB (DIA. 12) ASSY (B), FLAT
1-775-389-11 WIRE (FLAT TYPE)(31 CORE)
Remark
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
Ref. No.
Part No.
* 107
108
109
3-670-570-00 SPACER, SUPPORT
4-924-098-01 HOLDER, PC BOARD
X-3374-441-1 PANEL (CASSETTE) ASSY
110
111
! T901
! T901
4-886-821-11
3-701-418-00
1-427-889-11
1-427-890-11
– 61 –
Description
SCREW, S TIGHT, +PTTWH 3X6
WASHER, SPECIAL
TRANSFORMER, POWER (US,CND)
TRANSFORMER, POWER (AEP,UK)
Remark
6-4. CASSETTE COMPARTMENT SECTION
160
not supplied
162
166
#2
163
164
157
159
162
161
#5
157
158
157
#5
156
152
153
155
165
154
157
156
151
Ref. No.
Part No.
Description
151
152
153
154
* 155
3-373-224-01
3-373-237-03
3-373-223-01
3-373-222-01
3-373-217-01
HOLDER (LOWER)
HOLDER (UPPER), CASSETTE
SLIDER (L)
SLIDER (R)
SHAFT (JOINT)
156
157
158
159
3-345-648-61
3-318-201-11
3-373-218-01
3-373-219-01
SCREW (M1.4), TOOTHED LOCK
SCREW (B)(1.4X3), TAPPING
LEVER (R)
LEVER (L)
Remark
Ref. No.
Part No.
Description
160
4-931-471-01 SCREW (STEP)
161
162
163
164
165
3-632-859-00
3-318-203-61
3-373-215-01
3-373-216-01
3-382-648-01
166
3-373-212-01 SPRING (CASSETTE)
– 62 –
SPRING, BRAKE LEVER RETURN
SCREW (B1.7X4), TAPPING
SPRING (R), TORSION
SPRING (L), TORSION
HOLDER (WINDOW)
Remark
6-5. CHASSIS L/R SECTION
209
#13
208
M901
206
#20
203
#14
207
#7
DATM-110A
203
201
not supplied
205
202 203 204
#13
Ref. No.
201
202
203
204
205
Part No.
Description
4-931-470-01
3-373-214-01
2-623-756-01
3-373-213-01
A-2004-153-E
BELT (DRIVING)
PULLEY
SCREW, (B1.7X3), TAPPING
GEAR, DRIVING
CHASSIS (L) ASSY
Remark
Ref. No.
Part No.
Description
206
* 207
* 208
* 209
M901
3-373-221-01
1-655-916-11
1-655-913-11
3-373-235-01
X-3370-655-1
SLIDER (RACK)
CASSETTE COMPARTMENT SW BOARD
CASSETTE COMPARTMENT MOTOR BOARD
CHASSIS (R)
MOTOR ASSY (CASSETTE COMPARTMENT)
– 63 –
Remark
6-6. MECHANISM SECTION-1 (DATM-110A) 314
323
324
314
341
321
#16
#16
#11
M900
338
#17
341 337
336
339
342 326
311
320
343
310
#17
307
306 325
346
#13
#18
305
322
333
328
#18
332
not supplied
334
309
305
309
308
329
304
319
302
#21
M902
304
302
319 303
315
317
308
not supplied
303
312
345
316
318
331
312
#13
340
not supplied
301
313
344
326
335
326
#13
#3
Ref. No.
Part No.
Description
Ref. No.
#8
Part No.
* 301
* 302
303
304
* 305
X-3366-740-1
3-368-390-01
3-368-409-01
3-368-413-01
3-368-442-01
CHASSIS ASSY, MECHANICAL
BASE (#1 GUIDE)
JOINT (#1 GUIDE)
SCREW (1.4), +P TAPPING (B)
CATCHER
326
* 327
328
* 329
330
3-368-414-01
A-2001-587-A
3-927-039-01
3-368-391-01
3-831-441-XX
SHAFT (CAM SLIDER GUIDE)
RF COMPLETE ASSY
LEVER (CLEANER)
BRACKET (RF)
CUSHION, SPEAKER
306
307
308
309
310
3-368-399-01
3-908-644-01
3-368-436-01
X-3371-518-1
X-3363-025-1
GUIDE, ROLLER
SHAFT (ROLLER GUIDE)
SPRING (#1 GUIDE), COMPRESSION
ROLLER GUIDE ASSY
PINCH LEVER ASSY
* 331
332
333
334
* 335
A-2007-742-A
3-927-040-01
3-927-041-01
3-701-436-11
3-343-491-01
DRUM DRIVE BOARD, COMPLETE
SHEET (CLEANER)
SPRING (16G), TENSION
WASHER, STOPPER
HOLDER (S SENSOR B)
311
312
* 313
314
315
3-315-384-31
3-368-398-01
A-2003-708-A
3-372-761-01
3-368-427-01
WASHER, STOPPER
BUSHING
SLIDER ASSY, CAM
SCREW (M1.7X4), TAPPING
LEVER (LOAD-T)
336
337
338
339
* 340
3-337-677-01
3-337-676-01
3-337-605-01
3-389-294-01
A-2006-455-A
FLANGE
GUIDE, FIXED
NUT, ADJUSTMENT
SPRING (T2 300G), COMPRESSION
RF AMP BOARD, COMPLETE
316
317
318
319
320
3-368-426-01
3-368-444-01
3-368-443-01
3-368-415-01
3-384-243-01
LEVER (LOAD-S)
GEAR (LOAD-T)
GEAR (LOAD-S)
SHAFT (LOAD LEVER JOINT)
GUIDE (T3), ROLLER
* 341
* 342
343
344
345
3-368-457-01
3-368-456-01
3-387-983-01
3-368-439-01
3-368-441-01
HOLDER (END SENSOR)(RECIEVE)
HOLDER (END SENSOR LIGHT)
POLY-SLIDER (T3 GUIDE)
SPRING (PINCH PRESS), TENSION
SPRING (SLIDER S), TENSION
* 321
322
* 323
* 324
325
1-667-961-11
3-337-674-01
1-667-960-11
1-667-959-11
3-321-041-01
T/E SENSOR BOARD
SHAFT, GUIDE
RGN SW BOARD
CAM SLIDER BOARD
SCREW (M1.7X3.5), TAPPING
* 346
M900
M902
1-667-963-11 THIN BOARD
8-848-567-11 DRUM ASSY DOU-03A
8-835-361-01 MOTOR, DC U-17B (CAPSTAN)
327
330
Remark
– 64 –
#3
Description
Remark
6-7. MECHANISM SECTION-2 (DATM-110A)
351
367
382
351
not supplied
not supplied
not supplied
not supplied
367
383
357
355
376
380
375
356
#12
374
373
369
370
353
359
366
381
352
368
364
356
364
354
360
365
356
363
358
386
356
362
377
377
371
356
361
372
371
379
356
384
not
supplied
#6
378
385
Ref. No.
Part No.
Description
351
352
353
* 354
355
3-315-384-01
3-375-210-01
3-368-422-01
3-368-455-01
3-368-418-01
WASHER, STOPPER
SHAFT (GOOSENECK GEAR)
POLY-SLIDER(DIA. 5.5-DIA. 1.5)
LEVER (GEAR LOCK)
TUBE (BREAK)
356
357
358
359
* 360
3-368-398-01
3-368-430-01
X-3363-022-1
3-923-260-01
3-368-453-01
BUSHING
SPRING (GEAR LOCK)
GEAR (REEL DRIVE) ASSY
SPRING, COMPRESSION
LEVER (BRAKE SOLENOID)
* 361
* 362
363
364
365
3-368-447-01
3-368-446-01
3-368-438-01
3-905-586-02
3-368-422-11
LEVER (BRAKE S)
LEVER (BRAKE T)
SPRING (BREAK), TENSION
SPRING (FF/REW), COMPRESSION
POLY-SLIDER(DIA. 5.5-DIA. 1.5)
366
367
368
369
3-368-406-01
3-578-224-00
3-923-261-01
3-368-450-01
GEAR (GOOSENECK)
WASHER
SPRING (FR LEVER), COMPRESSION
LEVER (F/R)
Remark
Ref. No.
Part No.
Description
370
3-315-384-31 WASHER, STOPPER
371
372
373
374
375
3-377-332-01
3-368-415-01
3-368-421-01
3-373-039-01
3-368-403-01
TUBE (BREAK2)
SHAFT (LOAD LEVER JOINT)
GEAR (CAM DRIVE C)
GEAR (CAM DRIVE B)
GEAR (CAM DRIVE D)
376
377
378
* 379
380
3-368-402-01
X-3363-024-1
X-3369-126-1
3-368-454-01
X-3364-581-4
GEAR (CAM DRIVE A,B)
LEVER (BT) ASSY
LEVER (BT SOLENOID)
LEVER (BT SELECTION)
LEVER (F/R) ASSY
381
382
383
384
385
3-701-436-01
A-2004-476-A
A-2004-475-A
3-383-478-01
3-368-417-01
WASHER, 1.6
TABLE (T) ASSY, REEL
TABLE (S) ASSY, REEL
SPRING (B.T LEVER RETURN)
BELT (170TN10-1.0T), TIMING
386
3-701-436-01 WASHER, 1.6
– 65 –
Remark
6-8. MECHANISM SECTION-3 (DATM-110A)
PM903
#10
408
409
404
410
not supplied
#11
407
M905
PM904
#14
403
not supplied
405
406
#15
#9
402
401
M903
Ref. No.
Part No.
Description
* 401
* 402
403
404
405
A-2004-478-A
X-3366-312-1
3-368-431-01
2-623-756-01
3-368-423-01
CHASSIS (REEL) ASSY
CHASSIS ASSY, REEL
SPRING (B.T SOLENOID)
SCREW, (B1.7X3), TAPPING
SCREW (M2.6), STEP
* 406
407
3-368-416-01 BRACKET (B.T SOLENOID)
3-919-599-01 SPACER (P)
Remark
Ref. No.
Part No.
408
* 409
410
3-905-867-01 SPRING (STOPPER)
1-667-962-11 REEL MOTOR BOARD
3-380-525-01 ARBOR (BT ADJUSTMENT), MAVABLE
M903
M905
PM903
PM904
– 66 –
X-3363-109-1
X-3363-110-2
1-454-732-11
1-454-536-11
Description
MOTOR (CAM) ASSY
MOTOR (REEL) ASSY
SOLENOID, PLUNGER (BRAKE)
SOLENOID, PLUNGER (TENSION)
Remark
AC SW CAM SLIDER
SECTION 7
ELECTRICAL PARTS LIST CASSETTE COMPARTMENT MOTOR
CASSETTE COMPARTMENT SW
COAX I/O
Note:
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
When indicating parts by reference
number, please include the board
name.
Ref. No.
Part No.
*
1-661-403-11 AC SW BOARD
***********
• Due to standardization, replacements in the parts list
may be different from the parts specified in the
diagrams or the components used on the set.
• -XX, -X mean standardized parts, so they may have
some difference from the original one.
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
• RESISTORS
All resistors are in ohms
METAL: Metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F : nonflammable
Description
Remark
Ref. No.
Part No.
*
1-655-916-11 CASSETTE COMPARTMENT SW BOARD
********************************
< CONNECTOR >
CN004
• SEMICONDUCTORS
In each case, u: µ , for example:
uA...: µ A..., uPA...: µ PA..., uPB...: µ PB...,
uPC...: µ PC..., uPD...: µ PD...
• CAPACITORS
uF : µ F
• COILS
uH : µ H
• Abbreviation
CND : Canadian model
Description
Remark
< SWITCH >
1-580-230-51 PIN, CONNECTOR (PC BOARD) 2P
S1
S2
1-571-958-11 SWITCH, PUSH (1 KEY)(CASSETTE LOCK)
1-571-958-11 SWITCH, PUSH (1 KEY)(CASSETTE OUT)
< SWITCH >
**************************************************************
! S001
1-572-267-51 SWITCH, PUSH (AC POWER)(1 KEY)(POWER)
1-661-402-11 COAX I/O BOARD
**************
*
**************************************************************
*
1-667-959-11 CAM SLIDER BOARD
****************
*
1-535-303-00 WIRE, JUMPER
< CAPACITOR >
C520
C523
C524
C525
C526
< SWITCH >
SW1
SW2
1-162-306-11
1-162-179-11
1-162-282-31
1-162-306-11
1-164-159-11
1-570-953-11 SWITCH, PUSH (1 KEY)(STOP DET)
1-570-953-11 SWITCH, PUSH (1 KEY)(FWD DET)
* CN521
J521
J522
0.1uF
10%
< RESISTOR >
R521
R522
R523
R524
1-564-498-11 PIN, CONNECTOR 5P
1-564-337-00 PIN, CONNECTOR 3P
< MOTOR >
M901
1-770-905-11 JACK, PIN 1P (DIGITAL COAXIAL IN)
1-778-228-11 JACK, PIN 1P (DIGITAL COAXIAL OUT)
25V
< CONNECTOR >
* CN1
* CN2
10%
20%
16V
50V
50V
16V
50V
< JACK >
< CAPACITOR >
1-161-772-11 CERAMIC
20%
1-564-506-11 PLUG, CONNECTOR 3P
1-655-913-11 CASSETTE COMPARTMENT MOTOR BOARD
***********************************
C1
0.01uF
0.1uF
100PF
0.01uF
0.1uF
< CONNECTOR >
**************************************************************
*
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
1-247-804-11
1-249-401-11
1-247-804-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
75
47
75
1K
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W F
< TRANSFORMER >
X-3370-655-1 MOTOR ASSY (CASSETTE COMPARTMENT)
T521
**************************************************************
1-409-594-11 COIL (WITH CORE)
**************************************************************
– 67 –
DISPLAY
DRUM DRIVE
Ref. No.
Part No.
*
A-2007-739-A DISPLAY BOARD, COMPLETE
************************
Description
Remark
*
*
4-932-810-11 CUSHION (FL)
4-947-170-01 HOLDER
Ref. No.
< CAPACITOR >
C881
C882
C883
C884
C885
1-164-096-11
1-164-096-11
1-164-096-11
1-126-177-11
1-164-096-11
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
0.01uF
0.01uF
0.01uF
100uF
0.01uF
C886
1-164-096-11 CERAMIC
0.01uF
20%
50V
50V
50V
10V
50V
50V
< CONNECTOR >
CN801
1-568-860-11 SOCKET, CONNECTOR 17P
Part No.
Description
R831
R841
R851
R861
R871
1-249-427-11
1-249-437-11
1-249-427-11
1-249-437-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
47K
6.8K
47K
47K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W F
1/4W
1/4W
R881
R882
R883
R884
R885
1-249-417-11
1-249-437-11
1-249-437-11
1-249-437-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W
1/4W
R886
R887
R888
R889
R890
1-249-437-11
1-249-417-11
1-249-437-11
1-249-437-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
1K
47K
47K
10K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W
1/4W
R891
1-249-429-11 CARBON
10K
5%
1/4W
< COMPOSITION CIRCUIT BLOCK >
CP801
CP802
CP803
CP804
1-233-566-11
1-233-566-11
1-233-566-11
1-233-566-11
Remark
< SWITCH >
COMPOSITION CIRCUIT BLOCK
COMPOSITION CIRCUIT BLOCK
COMPOSITION CIRCUIT BLOCK
COMPOSITION CIRCUIT BLOCK
S802
S803
S804
S805
S806
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
SWITCH, KEY BOARD (STOP p)
SWITCH, KEY BOARD (PLAY ()
SWITCH, KEY BOARD (AMS, SELECT, =)
SWITCH, KEY BOARD (AMS, SELECT, +)
SWITCH, KEY BOARD (MODE, MENU)
S807
S811
S812
S813
S814
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
SWITCH, KEY BOARD (RESET, ENTER)
SWITCH, KEY BOARD (DATA, REW 0)
SWITCH, KEY BOARD (DATA, FF ))
SWITCH, KEY BOARD (REC r)
SWITCH, KEY BOARD (PAUSE P)
S815
S817
1-554-937-11 SWITCH, KEY BOARD (REC MUTE R)
1-571-520-11 SWITCH, SLIDE (INPUT)
< FLUORESCENT INDICATOR >
FL801
1-517-382-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC801
IC802
8-752-890-04 IC CXP82320-086Q
8-759-995-09 IC MSM6338RS
< TRANSISTOR >
< VIBRATOR >
Q801
Q802
Q803
8-729-620-05 TRANSISTOR 2SC2603-EF
8-729-620-05 TRANSISTOR 2SC2603-EF
8-729-620-05 TRANSISTOR 2SC2603-EF
X801
1-577-359-21 VIBRATOR, CERAMIC (4.19MHz)
**************************************************************
< RESISTOR >
R801
R802
R803
R804
R805
1-249-427-11
1-249-415-11
1-249-417-11
1-249-419-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
680
1K
1.5K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
F
F
F
F
R806
R807
R811
R812
R813
1-249-425-11
1-249-429-11
1-249-427-11
1-249-415-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
10K
6.8K
680
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
F
R814
R815
R817
R818
R821
1-249-419-11
1-247-843-11
1-249-431-11
1-249-435-11
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.5K
3.3K
15K
33K
6.8K
5%
5%
5%
5%
5%
*
A-2007-742-A DRUM DRIVE BOARD, COMPLETE
***************************
*
3-343-491-01 HOLDER (S SENSOR B)
< CAPACITOR >
F
F
F
C01
C02
C03
C04
C05
1-126-176-11
1-126-177-11
1-126-301-11
1-164-161-11
1-163-017-00
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
220uF
100uF
1uF
0.0022uF
0.0047uF
20%
20%
20%
10%
5%
10V
10V
50V
100V
50V
1/4W F
1/4W
1/4W
1/4W
1/4W F
C08
C10
C11
C12
C21
1-163-001-11
1-164-232-11
1-164-161-11
1-163-038-91
1-163-001-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.01uF
0.0022uF
0.1uF
220PF
10%
50V
50V
100V
25V
50V
– 68 –
10%
10%
DRUM DRIVE
Ref. No.
C31
C32
C33
C34
C35
Part No.
Description
1-163-001-11
1-164-232-11
1-163-038-91
1-163-038-91
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.01uF
0.1uF
0.1uF
0.1uF
10%
CN01
CN02
CN03
CN04
CN06
1-691-459-21
1-564-704-11
1-564-338-00
1-564-336-00
1-564-339-00
PIN, CONNECTOR (PC BOARD) 3P
PIN, CONNECTOR (SMALL TYPE) 2P
PIN, CONNECTOR 4P
PIN, CONNECTOR 2P
PIN, CONNECTOR 5P
CN07
* CN08
* CN09
* CN10
1-564-721-11
1-568-873-11
1-564-706-11
1-564-719-11
PIN, CONNECTOR (SMALL TYPE) 5P
SOCKET, CONNECTOR 31P
PIN, CONNECTOR (SMALL TYPE) 4P
PIN, CONNECTOR (SMALL TYPE) 3P
Part No.
IL COVER
Remark
Ref. No.
50V
50V
25V
25V
25V
R25
R26
1-216-105-91 METAL GLAZE
1-216-065-00 METAL CHIP
220K
4.7K
5%
5%
1/10W
1/10W
R31
R32
R35
R36
1-216-073-00
1-216-081-00
1-216-105-91
1-216-065-00
10K
22K
220K
4.7K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< CONNECTOR >
*
*
*
*
HEADPHONE
Description
Remark
METAL CHIP
METAL CHIP
METAL GLAZE
METAL CHIP
**************************************************************
1-656-334-11 HEADPHONE BOARD
***************
*
< CAPACITOR >
C681
C682
1-126-934-11 ELECT
1-126-934-11 ELECT
220uF
220uF
20%
20%
16V
16V
< CONNECTOR >
< IC >
CN652
IC01
IC02
IC03
1-564-510-11 PLUG (MICRO CONNECTOR) 6P
8-759-148-05 IC CXA8010M
8-759-701-01 IC NJM2904M
8-759-701-01 IC NJM2904M
< IC >
IC601
8-759-602-83 IC M5238P
< TERMINAL >
< JACK >
LUG01
1-537-770-21 TERMINAL BOARD, GROUND
J601
1-770-904-11 JACK (LARGE TYPE)(PHONES)
< PHOTO INTERRUPTER >
< COIL >
PH01
PH02
8-719-939-23 PHOTO INTERRUPTER GP-2S09-C
8-719-939-23 PHOTO INTERRUPTER GP-2S09-C
L399
L400
1-236-163-11 ENCAPSULATED COMPONENT
1-236-163-11 ENCAPSULATED COMPONENT
< TRANSISTOR >
< RESISTOR >
Q01
Q02
8-729-620-05 TRANSISTOR 2SC2603-EF
8-729-801-84 TRANSISTOR 2SB1013-4
R231
R232
R233
R234
R281
1-249-435-11
1-249-425-11
1-249-433-11
1-247-807-31
1-249-435-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
4.7K
22K
100
33K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W
1/4W
R282
R283
R284
! R691
! R692
1-249-425-11
1-249-433-11
1-247-807-31
1-808-374-11
1-808-374-11
CARBON
4.7K
CARBON
22K
CARBON
100
THERMISTOR, POSITIVE
THERMISTOR, POSITIVE
5%
5%
5%
1/4W F
1/4W
1/4W
< RESISTOR >
R01
R02
R03
R04
R05
1-216-061-00
1-216-073-00
1-216-029-00
1-216-057-00
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
10K
150
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R06
R07
R08
R09
R10
1-216-085-00
1-216-025-91
1-216-049-91
1-216-073-00
1-216-073-00
METAL CHIP
METAL GLAZE
METAL GLAZE
METAL CHIP
METAL CHIP
33K
100
1K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R11
R12
R13
R14
R21
1-216-073-00
1-216-113-00
1-216-073-00
1-216-037-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
470K
10K
330
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R22
R23
R24
1-216-081-00 METAL CHIP
1-216-077-00 METAL CHIP
1-216-069-00 METAL CHIP
22K
15K
6.8K
5%
5%
5%
1/10W
1/10W
1/10W
< VARIABLE RESISTOR >
RV651
1-223-620-11 RES, VAR, CARBON 20K/20K (PHONES LEVEL)
**************************************************************
*
1-661-406-11 IL COVER BOARD
**************
**************************************************************
– 69 –
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
INLET
MAIN
Ref. No.
Part No.
*
1-661-405-11 INLET BOARD
***********
Description
Remark
< CONNECTOR >
CN900
1-775-047-11 CORD (WITH CONNECTOR)
< INLET >
! IL001
1-251-234-11 INLET, AC (~ AC IN)
**************************************************************
*
A-2007-737-A MAIN BOARD, COMPLETE (US,CND)
******************************
*
A-2007-740-A MAIN BOARD, COMPLETE (AEP,UK)
******************************
*
1-533-213-31 HOLDER, FUSE
< CAPACITOR >
C101
C102
C103
C107
C151
1-126-933-11
1-162-286-31
1-126-933-11
1-130-481-00
1-126-933-11
ELECT
CERAMIC
ELECT
MYLAR
ELECT
100uF
220PF
100uF
0.0068uF
100uF
20%
10%
20%
5%
20%
10V
50V
10V
50V
10V
C152
C153
C157
C201
C202
1-162-286-31
1-126-933-11
1-130-481-00
1-130-471-00
1-110-341-11
CERAMIC
ELECT
MYLAR
MYLAR
MYLAR
220PF
100uF
0.0068uF
0.001uF
330PF
10%
20%
5%
5%
5%
50V
10V
50V
50V
50V
C203
C204
C205
C206
C207
1-110-341-11
1-130-471-00
1-130-479-00
1-126-933-11
1-162-302-11
MYLAR
MYLAR
MYLAR
ELECT
CERAMIC
330PF
0.001uF
0.0047uF
100uF
0.0022uF
5%
5%
5%
20%
30%
50V
50V
50V
10V
16V
C251
C252
C253
C254
C255
1-130-471-00
1-110-341-11
1-110-341-11
1-130-471-00
1-130-479-00
MYLAR
MYLAR
MYLAR
MYLAR
MYLAR
0.001uF
330PF
330PF
0.001uF
0.0047uF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C256
C257
C302
C304
C307
1-126-933-11
1-162-302-11
1-162-197-31
1-126-960-11
1-164-159-11
ELECT
CERAMIC
CERAMIC
ELECT
CERAMIC
100uF
0.0022uF
6.8PF
1uF
0.1uF
20%
30%
10%
20%
10V
16V
50V
50V
50V
C308
C309
C310
C311
C312
1-162-294-31
1-126-935-11
1-164-159-11
1-162-198-31
1-162-199-31
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
0.001uF
470uF
0.1uF
8.2PF
10PF
10%
20%
10%
5%
50V
6.3V
50V
50V
50V
C313
C314
C327
1-162-197-31 CERAMIC
1-162-197-31 CERAMIC
1-162-198-31 CERAMIC
6.8PF
6.8PF
8.2PF
10%
10%
10%
50V
50V
50V
Ref. No.
Part No.
Description
Remark
C332
C333
1-164-159-11 CERAMIC
1-162-211-31 CERAMIC
0.1uF
33PF
C334
C335
C336
C337
C338
1-126-964-11
1-162-306-11
1-164-159-11
1-164-159-11
1-164-159-11
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
10uF
0.01uF
0.1uF
0.1uF
0.1uF
C340
C341
C342
C343
C344
1-164-159-11
1-164-159-11
1-126-935-11
1-162-294-31
1-162-294-31
CERAMIC
CERAMIC
ELECT
CERAMIC
CERAMIC
0.1uF
0.1uF
470uF
0.001uF
0.001uF
C345
C351
C352
C353
C354
1-162-294-31
1-162-306-11
1-162-306-11
1-162-294-31
1-164-159-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.001uF
0.01uF
0.01uF
0.001uF
0.1uF
C355
C356
C361
C362
C431
1-164-159-11
1-164-159-11
1-162-302-11
1-162-302-11
1-162-302-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.0022uF
0.0022uF
0.0022uF
30%
30%
30%
50V
50V
16V
16V
16V
C432
C433
C439
C441
C442
1-162-302-11
1-162-286-31
1-162-306-11
1-162-302-11
1-162-302-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.0022uF
220PF
0.01uF
0.0022uF
0.0022uF
30%
10%
20%
30%
30%
16V
50V
16V
16V
16V
C443
C444
C445
C451
C452
1-162-286-31
1-126-964-11
1-162-306-11
1-162-306-11
1-126-963-11
CERAMIC
ELECT
CERAMIC
CERAMIC
ELECT
220PF
10uF
0.01uF
0.01uF
4.7uF
10%
20%
20%
20%
20%
50V
50V
16V
16V
50V
C453
C454
C459
C471
C481
1-126-338-11
1-162-306-11
1-162-306-11
1-162-306-11
1-162-306-11
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
47uF
0.01uF
0.01uF
0.01uF
0.01uF
20%
20%
20%
20%
20%
63V
16V
16V
16V
16V
C491
C492
C502
C503
C507
1-162-290-31
1-162-306-11
1-162-294-31
1-162-284-31
1-130-481-00
CERAMIC
CERAMIC
CERAMIC
CERAMIC
MYLAR
470PF
0.01uF
0.001uF
150PF
0.0068uF
10%
20%
10%
10%
5%
50V
16V
50V
50V
50V
C509
C511
C515
C527
C601
1-164-159-11
1-164-159-11
1-136-169-00
1-164-159-11
1-136-165-00
CERAMIC
CERAMIC
FILM
CERAMIC
FILM
0.1uF
0.1uF
0.22uF
0.1uF
0.1uF
5%
5%
50V
50V
50V
50V
50V
C602
C621
C622
C623
C624
1-136-165-00
1-126-964-11
1-126-964-11
1-136-165-00
1-136-165-00
FILM
ELECT
ELECT
FILM
FILM
0.1uF
10uF
10uF
0.1uF
0.1uF
5%
20%
20%
5%
5%
50V
50V
50V
50V
50V
– 70 –
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
5%
20%
20%
20%
10%
10%
10%
20%
20%
10%
50V
50V
50V
16V
50V
50V
50V
50V
50V
6.3V
50V
50V
50V
16V
16V
50V
50V
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
Ver 1.1 2001.06
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
C625
C626
C627
C628
C630
1-136-165-00
1-136-165-00
1-126-935-11
1-126-935-11
1-126-935-11
FILM
FILM
ELECT
ELECT
ELECT
0.1uF
0.1uF
470uF
470uF
470uF
5%
5%
20%
20%
20%
50V
50V
6.3V
6.3V
6.3V
* CN303
CN341
* CN401
1-568-836-11 SOCKET, CONNECTOR 17P
1-770-164-11 PIN, CONNECTOR (PC BOARD) 15P
1-564-339-00 PIN, CONNECTOR 5P
C651
C652
C653
C654
C661
1-136-165-00
1-136-165-00
1-136-165-00
1-136-165-00
1-136-165-00
FILM
FILM
FILM
FILM
FILM
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
* CN601
CN651
CN691
CN901
CN902
1-564-708-11
1-564-510-11
1-573-095-11
1-691-767-11
1-691-768-11
C662
C663
C664
C665
C666
1-136-165-00
1-136-165-00
1-136-165-00
1-136-165-00
1-136-165-00
FILM
FILM
FILM
FILM
FILM
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
D101
D102
D103
D104
D151
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
DIODE
DIODE
DIODE
DIODE
DIODE
1N4148M
1N4148M
1N4148M
1N4148M
1N4148M
C667
C668
C669
C670
C671
1-136-165-00
1-126-933-11
1-136-165-00
1-126-933-11
1-126-933-11
FILM
ELECT
FILM
ELECT
ELECT
0.1uF
100uF
0.1uF
100uF
100uF
5%
20%
5%
20%
20%
50V
10V
50V
10V
10V
D152
D153
D154
D321
D331
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
DIODE
DIODE
DIODE
DIODE
DIODE
1N4148M
1N4148M
1N4148M
1N4148M
1N4148M
C672
C673
C674
C675
C683
1-136-165-00
1-126-933-11
1-136-165-00
1-136-165-00
1-136-165-00
FILM
ELECT
FILM
FILM
FILM
0.1uF
100uF
0.1uF
0.1uF
0.1uF
5%
20%
5%
5%
5%
50V
10V
50V
50V
50V
D333
D411
D412
D413
D421
8-719-987-63
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
1N4148M
11ES2
11ES2
11ES2
11ES2
C684
C901
C902
C903
C904
1-126-935-11
1-126-953-11
1-126-939-11
1-126-935-11
1-126-916-11
ELECT
ELECT
ELECT
ELECT
ELECT
470uF
2200uF
10000uF
470uF
1000uF
20%
20%
20%
20%
20%
6.3V
35V
16V
6.3V
6.3V
D422
D501
D651
D901
D902
8-719-200-82
8-719-066-71
8-719-987-63
8-719-200-77
8-719-200-77
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
KV1555NT
1N4148M
10E2N
10E2N
C905
C906
C907
C908
C910
1-128-553-11
1-126-968-11
1-162-306-11
1-162-306-11
1-128-548-11
ELECT
ELECT
CERAMIC
CERAMIC
ELECT
220uF
100uF
0.01uF
0.01uF
4700uF
20%
20%
20%
20%
20%
63V
50V
16V
16V
25V
D903
D904
D905
D906
D907
8-719-200-77
8-719-200-77
8-719-312-47
8-719-200-82
8-719-987-63
DIODE
DIODE
DIODE
DIODE
DIODE
10E2N
10E2N
RBA-406B
11ES2
1N4148M
C911
C912
C913
C920
C921
1-126-960-11
1-126-767-11
1-162-306-11
1-128-548-11
1-162-306-11
ELECT
ELECT
CERAMIC
ELECT
CERAMIC
1uF
1000uF
0.01uF
4700uF
0.01uF
20%
20%
20%
20%
20%
50V
16V
16V
25V
16V
D908
D911
D912
D913
D914
8-719-015-13
8-719-200-77
8-719-200-77
8-719-200-77
8-719-200-77
DIODE
DIODE
DIODE
DIODE
DIODE
UZP-9.1BC-TP
10E2N
10E2N
10E2N
10E2N
C922
C923
C931
C932
C933
1-126-767-11
1-162-306-11
1-126-934-11
1-164-159-11
1-126-935-11
ELECT
CERAMIC
ELECT
CERAMIC
ELECT
1000uF
0.01uF
220uF
0.1uF
470uF
20%
20%
20%
16V
16V
16V
50V
6.3V
C934
C998
C999
1-136-165-00 FILM
1-164-159-11 CERAMIC
1-164-159-11 CERAMIC
0.1uF
0.1uF
0.1uF
5%
20%
< CONNECTOR >
* CN301
* CN302
1-564-706-31 PIN, CONNECTOR (SMALL TYPE) 4P
1-568-845-11 SOCKET, CONNECTOR 31P
50V
50V
50V
Description
Remark
PIN, CONNECTOR (SMALL TYPE) 6P
PLUG (MICRO CONNECTOR) 6P
SOCKET, CONNECTOR 15P
PLUG (MICRO CONNECTOR) 5P
PLUG (MICRO CONNECTOR) 6P
< DIODE >
< FUSE >
! F901
! F901
! F911
! F921
1-532-464-51
1-576-105-11
1-532-774-11
1-532-774-11
FUSE, TIME-LAG (T2.5AL 250V)(AEP,UK)
FUSE (2.5A 250V)(US,CND)
FUSE, MICRO (SECONDARY)(630mA 125V)
FUSE, MICRO (SECONDARY)(630mA 125V)
< IC >
IC301
IC302
IC304
IC305
IC306
– 71 –
8-759-927-46
8-759-701-01
8-752-355-55
8-752-364-91
8-759-925-90
IC
IC
IC
IC
IC
SN74HC00ANS
NJM2904M
CXD2605Q
CXK58257BM-10LL-T6
SN74HC74ANS
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
MAIN
Ref. No.
Part No.
Description
IC308
IC310
IC331
IC332
IC421
8-759-634-43
8-752-890-05
8-759-242-84
8-759-242-85
8-759-823-94
IC
IC
IC
IC
IC
M51953BFP
CXP87540-042Q
TORX176 (DIGITAL OPTICAL IN)
TOTX176 (DIGITAL OPTICAL OUT)
LB1836M
Remark
IC431
IC441
IC451
IC501
IC602
8-759-701-01
8-759-701-01
8-759-701-01
8-759-242-70
8-759-602-83
IC
IC
IC
IC
IC
NJM2904M
NJM2904M
NJM2904M
TC7WU04F
M5238P
IC603
IC604
IC605
IC606
IC651
8-759-330-53
8-759-602-67
8-759-189-33
8-759-094-53
8-759-900-72
IC
IC
IC
IC
IC
CXD8493M-E1
M5278L05
M5279L05-TP
TA7805S
NE5532P
IC652
IC653
IC654
IC681
IC901
8-759-900-72
8-759-370-62
8-759-602-67
8-759-634-50
8-759-069-28
IC
IC
IC
IC
IC
NE5532P
CXD8505BQ
M5278L05
M5218AL
PQ05RF11
IC902
IC903
IC904
IC999
8-759-069-28
8-759-602-66
8-759-390-48
8-759-426-52
IC
IC
IC
IC
PQ05RF11
M5230L-A
uPC2406AHF
AT24C01A-10SC-TP-B
< IC LINK >
! ICP911 1-532-837-21 LINK, IC (PRF630 0.63A)(AEP,UK)
! ICP921 1-532-837-21 LINK, IC (PRF630 0.63A)(AEP,UK)
Ref. No.
Part No.
Description
Remark
Q341
Q342
8-729-900-89 TRANSISTOR DTC144ES
8-729-422-57 TRANSISTOR UN4111
Q351
Q411
Q412
Q413
Q414
8-729-119-76
8-729-900-80
8-729-927-12
8-729-900-80
8-729-927-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1175-HFE
DTC114ES
2SC4115SQR
DTC114ES
2SA1585SQR
Q441
Q451
Q452
Q453
Q454
8-729-801-93
8-729-141-83
8-729-620-05
8-729-927-11
8-729-927-12
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1387
2SB1094-LK
2SC2603-EF
2SA1585SQR
2SC4115SQR
Q455
Q456
Q457
Q458
Q459
8-729-927-11
8-729-927-12
8-729-620-05
8-729-119-76
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1585SQR
2SC4115SQR
2SC2603-EF
2SA1175-HFE
2SC2603-EF
Q481
Q503
Q504
Q505
Q601
8-729-801-93
8-729-620-05
8-729-620-05
8-729-620-05
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1387
2SC2603-EF
2SC2603-EF
2SC2603-EF
DTC114ES
Q651
Q654
Q902
Q903
Q911
8-729-422-57
8-729-900-80
8-729-140-97
8-729-119-76
8-729-141-83
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UN4111
DTC114ES
2SB734-34
2SA1175-HFE
2SB1094-LK
Q921
8-729-209-15 TRANSISTOR 2SD2012
< JACK >
< RESISTOR >
* J101
1-569-443-11 JACK, PIN 4P (ANALOG (LINE))
< COIL >
L301
L302
L331
L341
L501
1-410-509-11
1-410-509-11
1-410-509-11
1-410-509-11
1-410-499-41
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
1.5uH
L502
L601
L991
1-410-509-11 INDUCTOR 10uH
1-410-509-11 INDUCTOR 10uH
1-410-509-11 INDUCTOR 10uH
< GROUND PLATE >
* LUG501 4-916-318-01 PLATE, GROUND
LUG502 1-537-770-21 TERMINAL BOARD, GROUND
< TRANSISTOR >
Q221
Q271
Q321
Q322
Q340
8-729-141-30
8-729-141-30
8-729-900-89
8-729-900-89
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3623A-LK
2SC3623A-LK
DTC144ES
DTC144ES
2SC2603-EF
R102
R103
R104
R105
R106
1-249-441-11
1-249-429-11
1-249-441-11
1-249-425-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
10K
100K
4.7K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W F
1/4W F
R107
R108
R152
R153
R154
1-249-401-11
1-249-401-11
1-249-441-11
1-249-429-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
47
47
100K
10K
100K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W
1/4W
1/4W
R155
R156
R157
R158
R201
1-249-425-11
1-249-425-11
1-249-401-11
1-249-401-11
1-259-440-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
4.7K
47
47
3.3K
5%
5%
5%
5%
1%
1/4W
1/4W
1/4W
1/4W
1/6W
R202
R203
R204
R205
R206
1-259-440-11
1-259-440-11
1-259-440-11
1-259-436-11
1-259-436-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
3.3K
3.3K
2.2K
2.2K
1%
1%
1%
1%
1%
1/6W
1/6W
1/6W
1/6W
1/6W
R207
1-259-444-11 CARBON
4.7K
1%
1/6W
– 72 –
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
F
F
F
F
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
MAIN
Ref. No.
Part No.
Description
R208
R209
R210
R211
1-259-444-11
1-249-419-11
1-249-419-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
4.7K
1.5K
1.5K
100K
1%
5%
5%
5%
Remark
1/6W
1/4W F
1/4W F
1/4W
R212
R213
R214
R221
R222
1-247-807-31
1-249-409-11
1-249-407-11
1-249-441-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
220
150
100K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W F
1/4W
1/4W F
R251
R252
R253
R254
R255
1-259-440-11
1-259-440-11
1-259-440-11
1-259-440-11
1-259-436-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
3.3K
3.3K
3.3K
2.2K
1%
1%
1%
1%
1%
1/6W
1/6W
1/6W
1/6W
1/6W
R256
R257
R258
R259
R260
1-259-436-11
1-259-444-11
1-259-444-11
1-249-419-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
4.7K
4.7K
1.5K
1.5K
1%
1%
1%
5%
5%
1/6W
1/6W
1/6W
1/4W F
1/4W F
R261
R262
R263
R264
R272
1-249-441-11
1-247-807-31
1-249-409-11
1-249-407-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100
220
150
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W F
1/4W F
1/4W F
R303
R305
R306
R307
R308
1-249-437-11
1-249-429-11
1-249-429-11
1-249-409-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
10K
10K
220
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W F
1/4W
R310
R321
R322
R323
R329
1-249-409-11
1-249-433-11
1-249-437-11
1-249-413-11
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
22K
47K
470
6.8K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W F
1/4W F
R330
R332
R333
R335
R336
1-249-409-11
1-249-437-11
1-249-417-11
1-247-807-31
1-249-431-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
47K
1K
100
15K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W F
1/4W
1/4W
R337
R338
R339
R340
R341
1-249-421-11
1-249-421-11
1-249-435-11
1-249-429-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
2.2K
33K
10K
4.7K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W
1/4W
1/4W F
R342
R343
R344
R345
R351
1-249-425-11
1-249-425-11
1-249-437-11
1-249-413-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
4.7K
47K
470
100K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W
1/4W F
1/4W
R352
R353
R354
1-249-441-11 CARBON
1-249-441-11 CARBON
1-249-441-11 CARBON
100K
100K
100K
5%
5%
5%
1/4W
1/4W
1/4W
Ref. No.
Part No.
Description
Remark
R355
R356
1-249-437-11 CARBON
1-249-437-11 CARBON
47K
47K
5%
5%
1/4W
1/4W
R357
R358
R359
R360
R361
1-249-429-11
1-249-429-11
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R362
R363
R364
R365
R366
1-249-413-11
1-249-429-11
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W
1/4W
R368
R369
R370
R371
R373
1-249-435-11
1-249-435-11
1-249-437-11
1-249-441-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
33K
47K
100K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W F
R374
R375
R376
R377
R378
1-249-429-11
1-249-429-11
1-249-429-11
1-249-429-11
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
10K
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W F
R379
R380
R381
R382
R383
1-249-417-11
1-249-437-11
1-249-409-11
1-249-411-11
1-249-411-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
47K
220
330
330
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W F
1/4W
1/4W
R391
R411
R412
R413
! R414
1-249-437-11
1-249-429-11
1-249-415-11
1-249-415-11
1-217-639-00
CARBON
CARBON
CARBON
CARBON
FUSIBLE
47K
10K
680
680
2.2
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W F
1/4W F
1/4W F
R415
R416
R431
R432
R433
1-249-415-11
1-249-415-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
680
100K
100K
100K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W
1/4W
1/4W
R434
R441
R442
R443
R444
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R445
R446
R447
R449
R450
1-249-433-11
1-249-401-11
1-249-441-11
1-249-441-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
22K
47
100K
100K
1K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W
1/4W F
R451
R452
R453
R454
R455
1-249-441-11
1-249-417-11
1-249-429-11
1-249-429-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
1K
10K
10K
100K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W
1/4W
– 73 –
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
MAIN
Ref. No.
PRIMARY
Part No.
Description
R456
R457
R458
R459
R461
1-249-417-11
1-249-417-11
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
100
100
100
5%
5%
5%
5%
5%
Remark
1/4W F
1/4W F
1/4W
1/4W
1/4W
R462
R463
R464
R465
R466
1-249-417-11
1-249-417-11
1-247-807-31
1-249-417-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
100
1K
100K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W
1/4W F
1/4W
R471
R472
R473
R481
R482
1-249-441-11
1-249-441-11
1-249-429-11
1-249-441-11
1-249-401-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
10K
100K
47
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W F
R483
R484
R485
R491
R492
1-249-437-11
1-249-437-11
1-249-441-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
47K
100K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W F
1/4W F
R493
R494
R501
R502
R503
1-249-407-11
1-247-807-31
1-249-417-11
1-249-429-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
150
100
1K
10K
100K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W F
1/4W
1/4W
R516
R517
R518
R525
R526
1-249-429-11
1-249-417-11
1-249-401-11
1-247-807-31
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
1K
47
100
10K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W F
1/4W
1/4W
R527
R528
R601
R603
R604
1-249-429-11
1-247-903-00
1-249-413-11
1-249-437-11
1-249-413-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
1M
470
47K
470
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W F
1/4W
1/4W F
R661
! R902
R903
R904
R905
1-247-903-00
1-212-873-11
1-260-111-11
1-249-433-11
1-249-425-11
CARBON
FUSIBLE
CARBON
CARBON
CARBON
1M
47
10K
22K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/2W
1/4W
1/4W F
R906
R907
R911
R912
R913
1-249-433-11
1-249-437-11
1-247-807-31
1-247-807-31
1-249-401-11
CARBON
CARBON
CARBON
CARBON
CARBON
22K
47K
100
100
47
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W F
R914
R915
R917
R918
R923
1-249-409-11
1-249-433-11
1-249-431-11
1-249-425-11
1-249-401-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
22K
15K
4.7K
47
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W F
1/4W F
R924
R927
1-249-409-11 CARBON
1-249-431-11 CARBON
220
15K
5%
5%
1/4W F
1/4W
Ref. No.
Part No.
! R931
R981
R982
1-219-123-11 FUSIBLE
1-249-411-11 CARBON
1-249-409-11 CARBON
Description
0.47
330
220
5%
5%
5%
Remark
1/4W F
1/4W
1/4W F
R983
R984
R985
R986
R991
1-249-409-11
1-249-415-11
1-249-409-11
1-249-417-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
680
220
1K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
F
F
F
F
R992
R998
R999
R1519
1-249-427-11
1-249-413-11
1-247-739-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
6.8K
470
100
2.2K
5%
5%
5%
5%
1/4W
1/4W
1/2W
1/4W
F
F
F
F
< VARIABLE RESISTOR >
RV451
1-241-765-11 RES, ADJ, CARBON 22K
< RELAY >
RY651
1-515-803-11 RELAY
< VIBRATOR >
X301
X302
X303
1-567-816-11 VIBRATOR, CRYSTAL (18MHz)
1-567-815-11 VIBRATOR, CRYSTAL (22MHz)
1-567-814-11 VIBRATOR, CRYSTAL (24MHz)
**************************************************************
1-661-401-11 PRIMARY BOARD
*************
*
< CAPACITOR >
! C001
! C002
! C003
! C004
! C005
1-113-916-11
1-113-916-11
1-113-920-11
1-113-920-11
1-113-920-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.01uF
0.01uF
0.0022uF
0.0022uF
0.0022uF
20%
20%
20%
20%
20%
250V
250V
250V
250V
250V
< CONNECTOR >
CN001
CN002
CN003
1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
1-580-230-51 PIN, CONNECTOR (PC BOARD) 2P
1-564-321-00 PIN, CONNECTOR 2P
< COIL >
! L001
1-424-485-11 FILTER, LINE
< GROUND PLATE >
* LUG001 3-346-266-12 PLATE, GROUND
**************************************************************
– 74 –
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
REC VOL
Ref. No.
Part No.
*
1-661-400-11 REC VOL BOARD
*************
Description
Remark
REEL MOTOR
Ref. No.
S826
S827
S831
S837
S851
< CONNECTOR >
* CN602
REMOCON
RF AMP
Part No.
Description
1-554-937-11
1-572-268-11
1-554-937-11
1-572-268-11
1-572-269-11
SWITCH, KEY BOARD (MARGIN RESET)
SWITCH, SLIDE (REC MDOE)
SWITCH, KEY BOARD (OPEN/CLOSE 6)
SWITCH, SLIDE (ID MODE)
SWITCH, SLIDE (SBM)
Remark
1-564-708-11 PIN, CONNECTOR (SMALL TYPE) 6P
**************************************************************
< RESISTOR >
A-2006-455-A RF AMP BOARD, COMPLETE
**********************
*
R101
R151
1-249-434-11 CARBON
1-249-434-11 CARBON
27K
27K
5%
5%
1/4W
1/4W
< CAPACITOR >
< VARIABLE RESISTOR >
RV101
1-241-937-11 RES, VAR, CARBON 20K/20K (REC LEVEL)
**************************************************************
1-667-962-11 REEL MOTOR BOARD
****************
*
< CAPACITOR >
C07
1-163-077-00 CERAMIC CHIP
0.1uF
10%
25V
< MOTOR >
M905
X-3363-110-2 MOTOR (REEL) ASSY
**************************************************************
1-661-399-11 REMOCON BOARD
*************
*
< CAPACITOR >
C891
1-164-096-11 CERAMIC
0.01uF
1-124-778-00
1-163-019-00
1-163-251-11
1-107-682-11
1-164-299-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.0068uF
100PF
1uF
0.22uF
20%
10%
5%
10%
10%
6.3V
50V
50V
16V
25V
C6
C7
C8
C9
C10
1-164-004-11
1-163-009-11
1-124-778-00
1-124-778-00
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.001uF
22uF
22uF
0.001uF
10%
10%
20%
20%
10%
25V
50V
6.3V
6.3V
50V
C11
C12
C13
C14
C15
1-164-004-11
1-164-299-11
1-107-682-11
1-163-251-11
1-124-778-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
0.22uF
1uF
100PF
22uF
10%
10%
10%
5%
20%
25V
25V
16V
50V
6.3V
C16
C17
C18
C19
C20
1-163-038-91
1-163-001-11
1-163-251-11
1-163-001-11
1-164-182-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
220PF
100PF
220PF
0.0033uF
10%
5%
10%
10%
25V
50V
50V
50V
50V
C21
C22
C23
C24
C25
1-163-005-11
1-126-603-11
1-163-251-11
1-163-038-91
1-124-778-00
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
470PF
4.7uF
100PF
0.1uF
22uF
C26
C27
C28
1-163-038-91 CERAMIC CHIP
1-107-682-11 CERAMIC CHIP
1-164-505-11 CERAMIC CHIP
50V
< IC >
IC891
C1
C2
C3
C4
C5
8-742-018-00 IC SBX1810-59
10%
20%
5%
20%
50V
35V
50V
25V
6.3V
< RESISTOR >
R822
R823
R824
R825
R826
1-249-415-11
1-249-417-11
1-249-419-11
1-247-843-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
1K
1.5K
3.3K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R827
R828
R837
R838
R852
1-249-429-11
1-249-435-11
1-249-433-11
1-249-435-11
1-249-439-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
33K
22K
33K
68K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
F
F
F
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
SWITCH, KEY BOARD (ID, AUTO)
SWITCH, KEY BOARD (ID, RENUNBER)
SWITCH, KEY BOARD (ID, REHEARSAL)
SWITCH, KEY BOARD (WRITE)
SWITCH, KEY BOARD (ERASE)
10%
< CONNECTOR >
F
* CN51
* CN52
1-566-207-11 PIN, CONNECTOR (PC BOARD) 14P
1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P
< IC >
IC1
< SWITCH >
S821
S822
S823
S824
S825
0.1uF
1uF
2.2uF
8-752-039-01 IC CXA1364R
< COIL >
L1
L2
L3
– 75 –
1-408-781-00 INDUCTOR CHIP 22uH
1-408-789-21 INDUCTOR CHIP 100uH
1-408-781-00 INDUCTOR CHIP 22uH
25V
16V
16V
RF AMP
Ref. No.
RGN SW
Part No.
SBM DF
Description
SW COVER
Remark
< RESISTOR >
R1
R2
R3
R4
R5
1-216-082-00
1-216-082-00
1-216-066-00
1-216-066-00
1-216-077-00
METAL GLAZE
METAL GLAZE
METAL CHIP
METAL CHIP
METAL CHIP
24K
24K
5.1K
5.1K
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R6
R7
R8
R9
R10
1-216-077-00
1-216-077-00
1-216-079-00
1-216-075-00
1-216-079-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
15K
18K
12K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R11
R12
R13
R14
R15
1-216-077-00
1-216-077-00
1-216-077-00
1-216-081-00
1-216-085-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
15K
15K
22K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R16
R17
R18
1-216-089-91 METAL GLAZE
1-216-080-00 METAL CHIP
1-216-073-00 METAL CHIP
47K
20K
10K
5%
5%
5%
1/10W
1/10W
1/10W
T/E SENSOR
THIN
Ref. No.
Part No.
*
1-661-404-11 SW COVER BOARD
**************
Description
Remark
**************************************************************
*
1-667-961-11 T/E SENSOR BOARD
****************
*
*
3-368-456-01 HOLDER (END SENSOR LIGHT)
3-368-457-01 HOLDER (END SENSOR) (RECEIVE)
< DIODE >
D01
8-719-988-42 DIODE GL453S
< PHOTO TRANSISTOR >
PH03
PH04
8-729-907-25 PHOTO TRANSISTOR PT4850F
8-729-907-25 PHOTO TRANSISTOR PT4850F
**************************************************************
1-667-963-11 THIN BOARD
**********
*
< VARIABLE RESISTOR >
< CONNECTOR >
RV1
RV2
1-238-181-11 RES, ADJ, CERMET 4.7K
1-238-181-11 RES, ADJ, CERMET 4.7K
* CN21
1-564-336-61 PIN, CONNECTOR 2P
< SWITCH >
**************************************************************
1-667-960-11 RGN SW BOARD
************
*
S02
1-572-458-11 SWITCH, PUSH (THIN DET)
**************************************************************
< SWITCH >
S01
MISCELLANEOUS
*************
1-571-878-11 SWITCH, PUSH (2 KEY)
(REC PROOF, CASSETTE IN)
**************************************************************
1-656-335-11 SBM DF BOARD
************
*
< CAPACITOR >
C631
C632
C633
C634
1-162-294-31
1-162-282-31
1-164-159-11
1-164-159-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.001uF
100PF
0.1uF
0.1uF
10%
10%
50V
50V
50V
50V
< CONNECTOR >
CN692
1-573-109-11 PIN, CONNECTOR 15P
70
106
FL801
! IL001
M900
1-775-464-11
1-775-389-11
1-517-382-11
1-251-234-11
8-848-567-11
WIRE (FLAT TYPE)(17 CORE)
WIRE (FLAT TYPE)(31 CORE)
INDICATOR TUBE, FLUORESCENT
INLET, AC
DRUM ASSY DOU-03A
M901
M902
M903
M905
PM903
X-3370-655-1
8-835-361-01
X-3363-109-1
X-3363-110-2
1-454-732-11
MOTOR ASSY (CASSETTE COMPARTMENT)
MOTOR, DC U-17B (CAPSTAN)
MOTOR (CAM) ASSY
MOTOR (REEL) ASSY
SOLENOID, PLUNGER (BRAKE)
PM904
RV101
! S001
! T901
! T901
1-454-536-11
1-241-937-11
1-572-267-51
1-427-889-11
1-427-890-11
SOLENOID, PLUNGER (TENSION)
RES, VAR, CARBON 20K/20K
SWITCH, PUSH (AC POWER)(1 KEY)(POWER)
TRANSFORMER, POWER (US,CND)
TRANSFORMER, POWER (AEP,UK)
< IC >
**************************************************************
IC607
8-759-196-21 IC CXD8482Q
< RESISTOR >
R631
1-249-413-11 CARBON
470
5%
1/4W F
**************************************************************
– 76 –
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
Ref. No.
Part No.
Description
Remark
ACCESSORIES & PACKING MATERIALS
*******************************
!
!
1-473-921-11
1-551-812-11
1-590-910-11
2-297-913-00
3-861-087-11
REMOTE COMMANDER (RM-D757)
CORD, POWER (US,CND)
CORD SET, POWER (AEP,UK)
WASHER (DIA.5), ORNAMENTAL
MANUAL, INSTRUCTION
(ENGLISH,FRENCH,GERMAN)
3-920-800-31
3-925-043-31
4-981-643-01
7-682-276-04
7-685-646-79
RACK (L/R)
PLATE, ORNAMENTAL
COVER, BATTERY (FOR RM-D757)
SCREW +RK 5X12
SCREW +BVTP 3X8 TYPE2 IT-3
**************************************************************
*************
HARDWARE LIST
*************
#1
#2
#3
#4
#5
7-685-851-04
7-685-645-79
7-685-534-19
7-685-871-01
7-621-772-20
SCREW +BVTT 2X4 (S)
SCREW +BVTP 3X6 TYPE2 IT-3
SCREW +BTP 2.6X8 TYPE2 N-S
SCREW +BVTT 3X6 (S)
SCREW +B 2X5
#6
#7
#8
#9
#10
7-627-854-07
7-685-102-19
7-685-533-19
7-627-450-28
7-627-852-27
PRECISION SCREW +P 2X2.5 TYPE3
SCREW +P 2X4 TYPE2 NON-SLIT
SCREW +BTP 2.6X6 TYPE2 N-S
+K 1.7X2
+P 1.7X3
#11
#12
#13
#14
#15
7-621-772-00
7-621-255-15
7-621-773-86
7-627-556-17
7-627-552-27
SCREW +B 2X3
SCREW +P 2X3
SCREW +B 2.6X4
SCREW,PRECISION +P 2.6X3 TYPE1
SCREW,PRECISION +P 1.7X2
#16
#17
#18
#20
#21
7-621-772-18
7-627-552-47
7-621-255-20
7-685-133-19
7-621-772-08
SCREW +B 2X4
SCREW,PRECISION +P 1.7X4
SCREW +BVTT 2X4 (S)
SCREW +BTP 2.6X6 TYPE2 N-S
SCREW +B 2X3
#22
#23
#24
#25
7-685-646-79
7-685-660-29
7-685-872-09
7-682-660-09
SCREW +BVTP 3X8 TYPE2 IT-3
SCREW +BVTP 4X10 TYPE2 SLIT
SCREW +BVTT 3X8 (S)
SCREW +PS 4X6
– 77 –
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque ! sont critiques pour
la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
PCM-R300
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.1
2001.06
Correction of electrical parts list (IC301).
1.0
1997.10
New
(SPM-01011)