Download DE - Farnell

EN
Programming
Explanation of some error codes:
Fehlercode
Hex.
Dez. Beschreibung
the
object number used in the telegram is
1 Code
1 0x7:
RS232:
Paritätsfehler
unknown
to
the
device.
is because
noterkannt)
all device types
2
2
RS232: Frame ErrorThis
(Startbit
o. Stopbit nicht
3 use all
3 object
Prüfsumme
nicht korrekt
numbers.
4
4
Startdelimiter falsch
of the data field in the telegram is
5 Code
5 0x8:
CAN:the
max.length
Nodes überschritten
6 defined
6
CAN:
unbekannt/keine
Gatewayfunktion
in
theNode
object
list. This error
code will be returned if
7
7
Objekt nicht definiert
a
set
value,
which
is
always
2
bytes
because of type „int“,
8
8
Objektlänge nicht korrekt
should
have
been
sent
but
the
data
field
9
9
Schreib-Leserechte verletzt, kein Zugriff only contained one
0A byte.10Even
CAN:
Gateway
if the
start überlastet
delimiter contained the correct telegram
0B length.
11 This
CAN:is
Gateway-Sendepuffer
voll setting wrong values.
a protection against
0C
12
CAN: geteilte Message abgebrochen
0D Code
13 0x9:
CAN:
anMessagebuffer
object to setüberlaufen
a set value has been sent, but the
0E
14
CAN: String-Startkennzeichen nicht korrekt
device is not in remote control mode. In this state you only
0F
15
Gerät ist in "Local" Modus
permission,Stuffing
but no
write permission. You need to
10 have
16read
CAN-Treiber-IC:
Fehler
11 set the
17 device
CAN-Treiber-IC:
CRC-Summenfehler
to remote
control mode first.
12
18
CAN-Treiber-IC: Übertragungsfehler
Messages
are deleted from the
13 Codes
19 0xB/0xD/0x14:
CAN: erwartete Datenlänge
stimmt nicht
14 message
20
CAN-Treiber-IC:
Puffer vollexecuted. In case they come
buffer, if correctly
20 in too
32 fast,
Gateway:
CAN Stuffing
Fehler
this buffer
will overflow
and can not receive any
21
33
Gateway: CAN CRC-Summenfehler
22 more
34messages.
Gateway: CAN Übertragungsfehler
30
48
Obere Grenze des Objektes überschritten
Code
0xE:
Strings have to be transferred differently when
31
49
Untere Grenze des Objektes unterschritten
If the string
length is greater than 8 characters,
32 using
50 CAN.
Zeitdefinition
nicht eingehalten
haveZugriff
to use
messages
are designated
with the
33 you 51
aufsplit
Menüparameter
nurthat
bei "Ausgang
aus"
34 string
52 start
Zugriff
auf Sequenzsteuerelemente
verweigert
tokens
0xFF, 0xFE etc. Also
see 7.7.1.
36
54
Zugriff auf Funktionsdaten verweigert
37 Codes
55 0x30/0x31:
Zugriff auf Sollwert
verweigert
(Gerät imto
Slavemodus)
these
are related
set values. All set
values have an upper and a lower limit, which are defineable
atKommunikationsfehler
the PSI 9000 power supplies. The default upper limit for
set
values is 0x6400 and the lower limit is 0.
Userfehler
Legende
Interner Fehler
Limits also apply to time values.
Error code
Hex.
Dec.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
0A
10
0B
11
0C
12
0D
13
0E
14
0F
15
10
16
11
17
12
18
13
19
14
20
20
32
21
33
22
34
30
48
31
49
32
50
33
51
34
52
36
54
37
55
Description
RS232: Parity error
RS232: Frame Error (Startbit or Stopbit incorrect)
Check sum incorrect
Start delimiter incorrect
CAN: max. nodes exceeded
CAN: node unknown/no gateway present
Object not defined
Object length incorrect
Read/Write permissions violated, no access
CAN: Gateway overload
CAN: Gateway send buffer full
CAN: Split message aborted
CAN: Message buffer overflow
CAN: String identifier incorrect
Device is in "local" mode
CAN driver chip: Stuffing error
CAN driver chip: CRC sum error
CAN driver chip: Form error
CAN: expected data length incorrect
CAN driver chip: Buffer full
Gateway: CAN Stuffing error
Gateway: CAN CRC check error
Gateway: CAN form error
Upper limit of object exceeded
Lower limit of object exceeded
Time definition not observed
Access to menu parameter only in standby
Access to sequence control denied
Access to function data denied
Access to set value denied (device is in slave mode)
Legend
Communication error
User error
Internal error
Code 0x32: a time value using the wrong time range has
been sent. The upper or lower limits are not exceeded by
the value, but it still causes this error.
Codes 0x36/0x37: Conditions for the access to these data
are not fulfilled. See object list about the access conditions
in column 4.
© 2009, Elektro-Automatik GmbH & Co. KG
88