Download User Manual

Introduction
Terminal wire connector function
Intramural interface circuit
Electric lock interface
This machine use relay, which makes sure this part
hasn't any connect. When the lock is opened, the relay
closed. The relay put out circuit is 2A.
Install
Sleeping function
When this machine in stay status, it will auto enter sleep status. This can reduce power
dissipation and prolong the machine's use life.
1
2
3
4
Red
NO
GND
Black
Gnd
NO
Blue
Relay output NO
Electric lock interface
COM
Purple
Relay output COM
NC
Orange
Relay output NC
wiring and fixation
Common powers connects diagram
Drill 4 holes on the wall
Thread the cable through cable hole
Wiring
When wiring completed, attach the rear plate to the wall firmly with at least three flat
head screws
5 Plug the cable harness
6. Attach the front cover to the rear plate
+12V
Red
+12V
GND
Black
GND
-V
Blue
NO
+V
Purple
-V
Orange
+V
Power on the
locks keep opening
Note Please don't power on before you connect finish.
Off power the
locks keep opening
PUSH
GND
+12V
NC
Fingerprint Sensor
OPEN
Red
Black
+V
-V
+
+
-
-
Power on the
locks keep opening
Important information
If holes are to be drilled before mounting onto a wall, check for hidden cables and/or pipes before drilling.
Use safety goggles when drilling or hammering in cable clips.
Every effort has been made to provide accurate information, however slight variations can occur. We also
reserve the right to make changed for product improvement at any time.
+12V
GND
V+
Blue
V-
Off power the
locks keep opening
Purple
Orange
NO
.3.
2.3 By Manager fingerprints
In programming mode, Press 1
1
input fingerprint twice 2
fingerprint twice *
ID number 1: Manager add fingerprint
ID number 2: Manager delete fingerprint
The first Fingerprint: Manager add Fingerprint, it is to add the users
The second Fingerprint: Manager delete Fingerprint, it is to delete users
input another
COM
To add one user:
NC
Press Manager add Fingerprint Input User Fingerprint twice Repeat Manager add Fingerprint
Note: We advise you use special adaptor, it will make your system work more stable.
.2 .
2 Add and delete Users
There are 3 ways to add and delete user, 1, by keypad; 2, by User ID; 3, by Manager
Fingerprint
2.1By keypad (the most convenient way)
Add User * manager password # 7 input fingerprint twice # *
(to add more than one user, just input finger continuously)
Delete User * manager password # 8 input fingerprint once # *
(to delete more than one user, just input finger continuously)
2.2 By User ID
To addone user: * Managerpassword # 1 IDnumber # Input userFingerprint twice # *
(User ID number can be any digit between 3- 120, but one ID number to one user.)
To add users continuously
st
nd
* Manager password # 1 3 # 1 User Fingerprint 4 # 2 user fingerprint......
N # Nth user fingerprint # *
To delete one user:
* Manager password # 2 ID number - # - *
To delete users continuously:
* Manager password # 2 ID number # ID number # .... ID number # # *
Open door button
Yellow
1 Manager mode (using Infrared remote control keypad)
1.1 Enter programming mode
Press * manager password #
Manager password: 9999 ( factory default setting)
1.2 Changing manager code
In programming mode, Press 0 new password code # Repeat new password code #
The manager code must be 4 digit number
NC
12V special power supply
Infrared Sensor
Operation guide
Note: When add fingerprint, please put the Fingerprint which you will add on the sensor twice, during which the light
shines red then turngreen, means the Fingerprintis added successfully. when delete users, justinput fingerprint once.
Special power supply
LED
When all connections are finished, you can power on. This time the buzzer will give a long
ring, and red led flashing. The machine will enter regular work status.
COM
Install diagram
Manager release alarm
When this machine is in stay status if it was opened, the buzzer will sound consecutive
long ring. And it will be kept for 1 minute.
.1.
OPEN
Yellow
Open door button
GND
Open door button operation function
This button is used to open the door.
Parma setting function
Open door time: 0~10s, default setting 5s. User can use infrared remote control keypad
setting.
Relay out
NC and COM: When power off the lock is opened.
NO and COM: When power on the lock is opened.
+12V power input
+ 12V
NO
Manager fingerprint operation function
ID number 1: Manager add fingerprint (can't open door, number 1 is used add users;
number2 is used deleted users)
ID number 2: Manager delete fingerprint
ID number 3~120: users fingerprint
User fingerprint operation function
ID number 3~120: users fingerprint are used open door.
Open door button
NC
A
Relay
Power on
Yellow
COM
Specifications
Manager infrared remote control keypad
Users use infrared remote control keypad, when enter the programming mode they can
operate as follow:
Changing manager code Add fingerprints Delete fingerprints Delete all fingerprints
release alarm Setting open door time Setting release alarm
OPEN
Common(12V/3A)
F007 use the precise electron circuit and good productive technology, which is the metal
structure fingerprint & access machine.
This machine uses the most advanced fingerprint identification technology, very safety.
Which is the most ideal choose. It is widely used in business affairs organization, office,
factory, housing district etc.
This product's programming is done by the infrared remote control keypad or fingerprint
manager. This product maximum can store 120 fingerprints. There are 2 fingerprint
managers, and each fingerprint has one ID code.
Note: input the user's fingerprint twice, during which the light shines red then turn green, means the
Fingerprint is added successfully.
.4.