Download CP6001-V User Guide, Revision 1.0

page
1
page
2
page
3
page
4
page
5
page
6
page
7
page
8
page
9
page
10
page
11
page
12
page
13
page
14
page
15
page
16
page
17
page
18
page
19
page
20
page
21
page
22
page
23
page
24
page
25
page
26
page
27
page
28
page
29
page
30
page
31
page
32
page
33
page
34
page
35
page
36
page
37
page
38
page
39
page
40
page
41
page
42
page
43
page
44
page
45
page
46
page
47
page
48
page
49
page
50
page
51
page
52
page
53
page
54
page
55
page
56
page
57
page
58
page
59
page
60
page
61
page
62
page
63
page
64
page
65
page
66
page
67
page
68
page
69
page
70
page
71
page
72
page
73
page
74
page
75
page
76
page
77
page
78
page
79
page
80
page
81
page
82
page
83
page
84
page
85
page
86
page
87
page
88
page
89
page
90
page
91
page
92
page
93
page
94
page
95
page
96
page
97
page
98
page
99
page
100
page
101
page
102
page
103
page
104
page
105
page
106
page
107
page
108
Transcript 
Installation
3.2
CP6001-V
CP6001-V Initial Installation Procedures
The following procedures are applicable only for the initial installation of the CP6001-V in a system. Procedures for standard removal and hot swap operations are found in their respective
chapters.
To perform an initial installation of the CP6001-V in a system proceed as follows:
1. Ensure that the safety requirements indicated in Chapter 3.1 are observed.
Warning!
PRELIMINARY
Failure to comply with the instruction above may cause damage to the
board or result in improper system operation.
2. Ensure that the board is properly configured for operation in accordance with application
requirements before installing. For information regarding the configuration of the
CP6001-V refer to Chapter 4. For the installation of CP6001-V specific peripheral devices,
refer to the appropriate sub-chapters in Chapter 3.
Warning!
Care must be taken when applying the procedures below to ensure that
neither the CP6001-V nor other system boards are physically damaged
by the application of these procedures.
3. To install the CP6001-V perform the following:
1. Ensure that no power is applied to the system before proceeding.
Warning!
Even though power may be removed from the system, the CP6001-V
front panel cables may have power applied which comes from an external source. In addition, these cables may be connected to devices that
can be damaged by electrostatic discharging or short-circuiting of pins.
It is the responsibility of the system designer or integrator to ensure that
appropriate measures are taken to preclude damage to the system or
injury to personnel which may arise from the handling of these cables
(connecting or disconnecting).
Kontron disclaims all liability for damage or injuries resulting from failure
to comply with the above.
Warning!
When performing the next step, DO NOT push the board into the backplane connectors. Use the ejector handles to seat the board into the
backplane connectors.
2. Carefully insert the board into the slot designated by the application requirements for
the board until it makes contact with the backplane connectors.
Page 3 - 4
ID 1022-4593, Rev. 1.0
Related documents
CP6001 USer Guide, Revision 2.0
CP6001 USer Guide, Revision 2.0
CP3002 User Guide, Rev. 2.0 (INTRODUCTION)
CP3002 User Guide, Rev. 2.0 (INTRODUCTION)
AM4022 User Guide, Rev. 1.0
AM4022 User Guide, Rev. 1.0
CP6004-RA/-RC User Guide, Rev. 1.0 (INTRODUCTION)
CP6004-RA/-RC User Guide, Rev. 1.0 (INTRODUCTION)
CP308 User Guide, Rev. 4.0
CP308 User Guide, Rev. 4.0
CP6004X Introduction User Manual
CP6004X Introduction User Manual
CP6500-V
CP6500-V
AM5030 User Guide, Rev. 10 - CBU Documentation Portail
AM5030 User Guide, Rev. 10 - CBU Documentation Portail
CP3003/CP3003-V User Guide, Rev. 2.0
CP3003/CP3003-V User Guide, Rev. 2.0
CP6000 - Kontron
CP6000 - Kontron
GE Fanuc / SBS CT7 Manual
GE Fanuc / SBS CT7 Manual
CP6005(X)-SA User Guide, Rev. 1.0 (INTRODUCTION)
CP6005(X)-SA User Guide, Rev. 1.0 (INTRODUCTION)