Download Multifunction Programmable Controller Installation and User manual

Installation and User manual of the AC10 - AC20 - AC30 controller
5.7.6
Failure Module ( FAIL ) ......................................................................................................................... 113
5.7.7
Power Failure AC Restart flag ( PWRF ) ............................................................................................... 113
5.7.8
Setpoint control key lock Block (SPKL).................................................................................................. 114
5.7.9
Output Change Key Lock Block (OPKL) ................................................................................................ 114
5.8
MATH AND LOGIC FUNCTION........................................................................................................................... 115
5.8.1
Expression ( EXP ).................................................................................................................................. 115
5.8.2
Arithmetic ( OPR ) .................................................................................................................................. 115
5.8.3
Function ( FN ) ....................................................................................................................................... 116
5.8.4
Analog Single Constant ( CNS ) ............................................................................................................. 117
5.8.5
AND ........................................................................................................................................................ 117
5.8.6
NOT ........................................................................................................................................................ 118
5.8.7
EOR (XOR) ............................................................................................................................................. 118
5.8.8
OR........................................................................................................................................................... 119
5.8.9
8 Inputs OR (OR8) .................................................................................................................................. 119
5.8.10 Flip-Flop J-K LATCH (JKF) .................................................................................................................. 120
5.8.11 D LATCH Flip-Flop ............................................................................................................................... 120
5.8.12 Monostable ( MST ) ................................................................................................................................ 121
5.8.13 Counter ( CNT ) ...................................................................................................................................... 122
5.8.14 Multiple Analog Constants ( MCNS ) ..................................................................................................... 122
5.8.15 Analog Single Constant ( CNS ) ............................................................................................................. 123
5.8.16 Multiple Digital Constant ( MDCN ) ...................................................................................................... 123
5.8.17 Analog To Digital converter ( A/D ) ....................................................................................................... 124
5.8.18 Digital To Analog Converter ( D/A ) ...................................................................................................... 124
5.8.19 AND_8 Block (AND8)............................................................................................................................. 125
5.8.20 Shift Block (SHFT).................................................................................................................................. 125
5.9
PROGRAMMER FUNCTIONS .............................................................................................................................. 127
5.9.1
Real Time Clock with 8 outputs ( R.T.C. ) .............................................................................................. 127
5.9.2
Setpoint Programmer (PRG) .................................................................................................................. 127
6.
PASSWORD AND ACCESS CONTROL .......................................................................................................... 135
6.1
SETTING ACCESS MODES................................................................................................................................. 135
6.2
PASSWORD CHANGE ........................................................................................................................................ 138
6.3
PASSWORD DELETE ......................................................................................................................................... 138
6.3.1
Don’t panic!............................................................................................................................................ 138
7.
MAINTENANCE AND DIAGNOSTIC.............................................................................................................. 139
7.1
ADJUSTMENT OF THE DISPLAY CONTRAST ....................................................................................................... 139
7.2
ERROR MESSAGES............................................................................................................................................ 139
7.3
MASTER RESET................................................................................................................................................ 140
7.4
DIAGNOSTIC TEST AND CALIBRATION ............................................................................................................. 140
7.4.1
Diagnostic Tests...................................................................................................................................... 141
7.4.2
Calibrations ............................................................................................................................................ 142
7.5
REPLACEMENT OF FAULTY COMPONENTS ....................................................................................................... 144
7.6
SPARE PARTS ................................................................................................................................................... 144
7.7
MANUALS ........................................................................................................................................................ 144
8.
EXPANSION UNIT.............................................................................................................................................. 145
8.1
GENERAL INFORMATIONS ................................................................................................................................ 145
8.2
TECHNICAL CHARACTERISTICS ........................................................................................................................ 145
8.3
INSTALLATION ................................................................................................................................................. 145
8.4
ELECTRICAL CONNECTIONS ............................................................................................................................. 146
8.4.1
RS-485 .................................................................................................................................................... 146
8.4.2
Power Supply.......................................................................................................................................... 147
8.4.3
Inputs and Outputs.................................................................................................................................. 147
8.5
AUXILIARY UNITS ADDRESSING ...................................................................................................................... 147
9.
ORDERING DATA .............................................................................................................................................. 148
9.1
9.2
10.
ORDERING CODE ............................................................................................................................................. 148
AUXILIARY UNITS ............................................................................................................................................ 148
ANNEX “A” RESIDENT CONFIGURATIONS ........................................................................................... 149
5