Download INSTALLATION MANUAL

Determination of indoor address
Is automatic address set up?
Automatic setup
Manual setup
Setup from central remote controller
Setup from wired remote controller
Manual address setup from
wired remote controller
Manual address setup with CODE No.
“C1” of central remote controller
1
1
2
3
4
5
6
7
VENT
TEST
Push
and
buttons
simultaneously for 4 seconds
or more.
UNIT
button.
Do not push
Set “03” to CODE No. with
and
temperature setup
buttons.
Using timer setup/time
and
buttons, set up the
central control address.
Registration completes with
SET
button. ( SETTING changes
from flashing to lighting.)
Push
TEST
button.
Initial setup starts.
(For approx. 1 minute)
End
Check method
Check overlap of central
control addresses
Make operation status by
buttons
pushing
of central remote controller
three times each.
When there is overlapped units
An alarm code “L20” is displayed on the remote controller
and alarm code “L20” or “P30”
on central remote controller,
respectively.
⎡ Wired remote controller:
⎤
⎢ Displayed immediately
⎥
⎢ central remote controller: ⎥
⎣ After 4 minutes at maximum ⎦
Overlapped
YES
Overlapped?
No overlap
2
3
4
5
6
7
8
9
Automatic address setup with
CODE No. “C2” of central
remote controller
Push
and ZONE buttons
simultaneously for 4 seconds or
more.
1
Set “C1” to CODE No. with
temperature setup
and
buttons.
2
Push
3
SET
button.
Select ZONE or
buttons to select zone and group to
be registered.
4
Using
and
, perform
registration. (Select the indoor unit.)
Registration completes with
button.
5
6
SET
Repeat procedure 4 to 6.
Push
7
Push
and ZONE
buttons simultaneously for 4
seconds or more.
Set “C2” to CODE No. with
temperature setup
and
buttons.
Push SET button and the
address setup starts. “C2”
goes on and SETTING flashes.
When SETTING goes off and “C2”
flashes, setup ends.
Push
button.
SETTING flashes and the initial
setup starts.
(For approx. 1 minute)
End
button.
SETTING flashes and the initial setup
starts.
10
End
(Example)
Central
control device
Outdoor unit
Outdoor unit
Indoor unit
Indoor unit
(Line - Indoor - Group)
1-1-0
*1
In case of digital inverter air conditioner,
if the same line address is set up to the
multiple indoor units which are controlled
collectively, the central control address
setup is impossible by this method.
1-2-0
<Central control address/zone/group correspondence table>
Central
Central
Central
Central
control Zone Group control Zone Group control Zone Group control Zone Group
Address
Address
Address
Address
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
End
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
99
18
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Not set up