1
Download CANdrive installation and operating instructions
Transcript
Operation and Maintenance Operation Maintenance and Warranty Gauge driver outputs The gauge outputs operate when CANdrive reads valid J1939 data for engine speed, oil pressure and coolant temperature. If CANdrive stops receiving valid data, the gauge outputs are maintained at the last known value for approximately 5 seconds, after which time the outputs turn off. CANdrive has no user-serviceable parts. Maintenance is therefore limited to the following preventative checks: Indicating LEDs All standard models have a green CAN LED. A flashing CAN LED indicates that CANdrive is powered, but is not receiving any J1939 data. A constantly lit CAN LED indicates power on with good CANbus connection and J1939 activity. (Note: J1939 activity can originate from ANY device on the CANbus network, and may not necessarily be valid data from the engine ECU.) Model CDV300R has additional LEDs for indication of J1939transmitted engine faults. CANdrive responds to single DM1 (active fault code) messages that contain SPN (Suspect Parameter Number), FMI (Fault Mode Indicator) and warning/stop lamp data. CANdrive also reads multi-packet transport messages broadcast using the BAM protocol. Check that electrical connections are secure. Check that the CANdrive is securely mounted, and kept free from ingress of water or build up of excessive dust/dirt. The front label and casing may be wiped with a clean, damp cloth. Do not use cleaning solvents. CANdrive is supplied with a 2 year warranty on parts and workmanship. In the event of a fault or technical query, please contact your Murphy representative for technical support. Further information Document Description 00-02-0251 EG(S)21 series electric gage installation 00-02-0258 AT series tachometer installation Typically, LEDs light continuously to indicate a shutdown fault, and flash to indicate a (non-shutdown) warning fault: LED Mode Fault On Low oil pressure shutdown Flashing Low oil pressure warning On Coolant temperature shutdown Flashing Coolant temperature warning On Overspeed shutdown Flashing Overspeed warning - Reserved for future use - Reserved for future use J1939 SPN FMI 100 1 100 > 1 110 0 110 > 0 190 0 190 > 0 - - Flashing Warning fault - - Flashing Shutdown fault - - CANdrive can handle up to 8 simultaneous faults at one time: additional fault messages are not registered. When a fault becomes inactive and is no longer broadcast, the appropriate LED goes out after approximately 2 seconds. ENOVATION CONTROLS CORPORATE HEADQUARTERS 5311 S 122ND EAST AVENUE, TULSA, OK 74146, USA ENOVATION CONTROLS – SAN ANTONIO OFFICE 5757 FARINON DRIVE, SAN ANTONIO, TX 78249, USA ENOVATION CONTROLS – HOUSTON OFFICE 105 RANDON DYER RD, ROSENBERG, TX 77471, USA ENOVATION CONTROLS LTD. – UNITED KINGDOM CHURCH ROAD, LAVERSTOCK, SALISBURY, SP1 1QZ, UK MURPHY ECONTROLS TECHNOLOGIES – CHINA 77 23RD STREET, HANGZHOU ECONOMIC & TECHNOLOGICAL DEVELOPMENT AREA, HANGZHOU, ZHEIJIANG 310018, CHINA CANdrive installation and operation SALES & SUPPORT, NORTH AMERICA MURPHY PRODUCTS: PHONE: 918 317 4100 FAX: 918 317 4266 EMAIL: [email protected] WWW.FWMURPHY.COM ECONTROLS PRODUCTS: PHONE: 210 495 9772 FAX: 210 495 9791 EMAIL: [email protected] WWW.ECONTROLS.COM MURPHY CONTROL SYSTEMS & SERVICES PHONE: 281 633 4500 FAX: 281 633 4588 EMAIL: [email protected] MURPHY INDUSTRIAL PANEL DIVISION PHONE: 918 317 4100 FAX: 918 317 4124 EMAIL: [email protected] SALES & SUPPORT, INTERNATIONAL EUROPE, MIDDLE EAST & AFRICA PHONE: +44 1722 410055 FAX: +44 1722 410088 EMAIL: [email protected] WWW.FWMURPHY.EU CHINA PHONE: +86 571 8788 6060 FAX: +86 571 8684 8878 EMAIL: [email protected] LATIN AMERICA & CARIBBEAN PHONE: +1 918 317 2500 EMAIL: [email protected] SOUTH KOREA PHONE: +82 70 7951 4100 EMAIL: [email protected] INDIA PHONE: +91 91581 37633 EMAIL: [email protected] FM 28221 (Tulsa, OK – USA) FM 28221 (Rosenberg, TX – USA) FM 620667 (San Antonio, TX – USA) FM 29422 (UK) FM 523851, TS 589322 (China) 00-02-0618 revision H 2015-07-13 p4/4
