Download USER MANUAL - memo

Transcript
Technical Specifications
7.4 Upgrading Firmware
To install the latest Kramer firmware version on a VP-724DS unit, connect the
COM port on your PC to the RS-232 port on the VP-724DS unit, as section 5.1
describes, and go to the Kramer Web site at: http://www.kramerelectronics.com.
8
Technical Specifications
Table 6 includes the technical specifications:
1
Table 6: Technical Specifications of the VP-724DS
VIDEO: 2 x composite video 1 Vpp/75 Ω on RCA connectors; 2 x Y/C (s-Video) 1 Vpp (Y),
0.3Vpp (C) / 75 Ω on 4 pin connectors; 1 x Component (Y, Pb/Cb, Pr/Cr) on RCA connectors;
2x VGA (VGA/SVGA/XGA/UXGA) on HD15F connectors; and 1x DVI connector
AUDIO: 2 x stereo audio on terminal block connectors (CV); 2 x stereo audio on
terminal block connectors (YC); 2 x stereo audio on terminal block connectors (VGA);
1 x stereo audio on a terminal block connector (component); and 1 x stereo audio on
a terminal block connector (DVI)
VIDEO: 1 x VGA/SVGA/XGA/UXGA as well as additional modes: 480p, 720, 1080i on
Outputs:
an HD15F connector
AUDIO: 1 x stereo audio on a terminal block connector
Output
VGA (640x480), SVGA (800x600), XGA (1024x768), SXGA (1280x1024), UXGA
Resolutions:
(1600x1200), 1024x852, 1024x1024, 1366x768, 1365x1024, 1280x720, 720x483, 852x480,
1400x1050. Also supports 480p, 720p, and 1080i, as well as a user definable output mode
Control:
Front panel buttons/ OSD, IR remote control, RS-232 on a DB-9 connector
Additional Controls: Different vertical refresh rates, ProcAmp control, output image scaling and aspect ratio change
Firmware:
Frame freeze, digital zoom 4X, PIP (video-in-graphics or graphics-in-video, in sizes of up to half a
screen, located anywhere on the screen), Flesh tone (special color processing), Gamma setting
H Frequency:
15.63~90kHz
V Frequency:
50~100Hz
Computer Resizing: Auto-resizing to panel pixel number
RGB Video Signal: RGB, 1.0 Vpp, 75 Ω
Inputs:
RGB Sync Signal:
Audio Input/Output
Voltage:
Plug and Play:
De-interlacing:
Film mode detection:
Power Source:
Dimensions:
Accessories:
Weight:
Separate H/VTTL, composite sync, analog
0~0.5 Vrms
DDC1 / DDC2B
Adaptive and pixel based
2:2 / 3:2 pull down reverse
100-240 VAC, 50/60 Hz, 30VA automatic power supply
19" (W), 9.3" (D) 1U (H) rack mountable2
IR remote control, power cord3
3 kg (6.6 lbs.) approx.
1 Specifications are subject to change without notice
2 When installing a Kramer machine on a closed or multi-unit rack assembly, be aware that the operating ambient temperature
of the rack environment may be greater than room ambient. In particular, take care that there is sufficient air flow. (Refer to
the "Operating Conditions.pdf" file on our Web site at http://www.kramerelectronics.com (click "FAQs" in the Technical
Support section))
3 We recommend that you use only the power cord that is supplied with this machine
36
KRAMER: SIMPLE CREATIVE TECHNOLOGY