Download XPC User's Guide - 3D ContentCentral

XPC Pin Clamp
User’s Guide
Rev_0.0
XPC Clamp Components
Pin, Finger and
Donut
25mm and 40mm pin
Standard Sizes
Power Cylinder
Sub-Assembly
Extension SubAssembly
350mm and 650mm
Standard Sizes
Reposition Finger on Clamp
STEP 1
Remove (4) screws
from Extension
Assembly
STEP 2
Rotate Extension
Assembly to
desired position in
90 degree
increments.
STEP 3
Reinstall (4)
screws.
No other
disassembly is
required.
Adjustable Mount Instructions
May be assembled in horizontal or
vertical orientations
Sensing Options
Cover Plate
Pepperl & Fuchs
2X for N (No Switch)
Installed opposite switch
DC Proximity Switch (P1/P2)
May be installed either side
Standard Rod End
Supplied with P1/P2 or N
Switch Options
Camera Sensing Flag
Supplied with C Option
STANDARD AVAILABLE PIN DIAMETERS
ALL PINS h6 TOLERANCE
A
110.0
70.0
PIN SELECTION
EXTENSION ASSEMBLY IS POSITIONABLE
IN 90 DEGREE INCREMENTS BY ONLY
REMOVING 4 SCREWS - NO DIS-ASSEMBLY
STANDARD PIN
DIAMETERS
HOLE TYPE
(ENGAGEMENT)
24.8
S, F
25.0
S, F
39.8
S, F
40.0
S, F
REV.
DATE
CHANGE
BY
EC101366
A
2014-01-30
REVISED ORDER CODES
ATS
-----
B
2014-03-07
REVISED AND CLARIFIED HEIGHT OPTION DIMENSIONS
ATS
BTM PIN CLAMPS CAN BE ORDERED WITH CUSTOM PIN CONFIGURATIONS
PIN COATING
39.8
40.0
24.8
25.0
B = BLACK OXIDE
0.8
110.0
ECN No.
0.8
A
70.0
4.8
9.5
HOW TO ORDER XPC CLAMPS
CONTACT BTM FOR NON-STANDARD OPTIONS
4.8
0.8
4X
XPC - G 25.0 F B 350 - 1 - P1 - XXXXXXXXX
HOLE TYPES
STANDARD HOLE
ORDER CODE "S"
18.0 THRU ALL
A
FLANGED HOLE
ORDER CODE "F"
B
0.5 MAX GAP BETWEEN
FINGER AND CLAMPING SURFACE
NOTE: WILL ONLY CLAMP
MATERIAL OVER 0.5MM
0.5 MAX GAP BETWEEN
FINGER AND CLAMPING SURFACE
NOTE: WILL ONLY CLAMP
MATERIAL OVER 0.5MM
21.9
CLAMPING SURFACE
MATERIAL MUST BE KEPT PARALLEL
WITH THE DONUT CLAMPING SURFACE
4.0
ENGAGEMENT
ENGAGEMENT
S = 4.0
F = 10.0
10.0
ENGAGEMENT
6.1
0.5 MAX GAP CLAMP FINGER TO DONUT
CLAMPING SURFACE
A
PORT:
G = G1/8
25.8
B
PIN DIAMETER (h6 TOLERANCE):
25.0
24.8
40.0
39.8
ENGAGEMENT
S = 4.0
F = 10.0
15.7
8.2
14.1
C
HOLE TYPE
(ENGAGEMENT)
D
34.5
(DONUT HEIGHT) B
78.5
50.0
HEIGHT OPTION
(TO CLAMP FINGER)
78.5
A
B
D
F
E
H
G
CLAMP SERIES
XPC
B
41.0
C
F
FINGER POSITION:
1
2
3
4
G
SENSING OPTIONS:
PEPPERL & FUCHS DC PROXIMITY
SWITCH:
P1 = SWITCH POSITON 1
P2 = SWITCH POSITION 2
33.7
15.5
PIN DIAMETER
h6 TOLERANCE
B
B
E
HOLE TYPE ENGAGEMENT:
S = STANDARD HOLE
F = FLANGED HOLE
CAMERA SENSING:
C
NO SWITCH:
N
PIN COATING:
B = BLACK OXIDE
H
HEIGHT OPTION:
350
650
SPECIAL OPTION
BTM Pin Clamps can be ordered with custom
designed (non-standard) pins, donuts, and/or
fingers. In such instances, a SPECIAL OPTION
number must be referenced when ordering a nonstandard pin clamp.
A
HEIGHT
FINGER POSITION
ORDER CODE
B
ORIENTATION
1
2
AS SHOWN BELOW
3
4
FROM BASE TO CLAMP FINGER AS SHOWN BELOW
ORDER CODE
DIMENSION
350
350mm
650
650mm
FINGER POSITION 2
ORDER CODE "2"
FINGER POSITION 1
ORDER CODE "1"
PORT SELECTION
76.2
PORT ORDER CODE
G = G1/8
B 650.0
HEIGHT OPTION
(TO CLAMP FINGER)
PISTON ROD
FINGER POSITION 3
ORDER CODE "3"
26.0
109.0
FINGER POSITION 4
ORDER CODE "4"
B
350
HEIGHT OPTION
(TO CLAMP FINGER)
CLOSE CLAMP PORT
G1/8 PORT
ROTATABLE 360
OPEN CLAMP PORT
G1/8
ROTATABLE 360
MANUAL RELEASE ROD
(PULL TO UNLOCK CYLINDER)
142.0
70.0
A
SENSING
DESCRIPTION
PEPPERL & FUCHS DC WORLD SWITCH
55.5
CAMERA SENSING - INCLUDES COVERS & SCRS.
NO SWITCH OPTION - INCLUDES COVERS &
SCRS.
4X
SWITCH POS 1
SWITCH POS 2
P1
P2
ALLOWS MULTIPLE MOUNTING POSITIONS
SEE DRAWING TPD281300M FOR MORE INFORMATION
C
N
OTHER SWITCH BRANDS ARE AVAILABLE - BUT NOT STOCKED. CONTACT BTM FOR DETAILS
70.0
84.3
OPTIONAL FITTING SPACER MOUNT
ORDER CODE
96.6
100.9±0.8 CLAMP CLOSED
18.0 THRU ALL
139.4±0.8 CLAMP OPEN
SWITCH POSITION 1
-- SPECIFICATIONS --
27.6
STANDARD ROD END
FLAG WILL BE INSTALLED
WHEN ORDERING
PROXIMITY SWITCH
OR NO SWITCH OPTION
CAMERA SENSING FLAG
ASSEMBLY
BORE SIZE: 38.1 [1.50] DIA. - 1140mm² [1.77 in²]
FINGER TRAVEL: 15mm [.59 in.]
5mm [.20 in.] ROTATIONAL
10mm [.39 in.] STRAIGHT LINE PULL DOWN STROKE
2.5mm [.10] LOCKING RANGE (FROM CLAMPING
SURFACE)
42.5
38.1
42.5
50.5
12.7
21.5
CLAMPING FORCE: 890 N -1334 N [200-300 lbs] @ 5.5
BAR [80 PSI]
SWITCH POSITION 1
(FRONT)
ORDER CODE "P1"
(RELATIVE TO PISTON ROD
AS SHOWN)
SWITCH POSITION 2
(BACK)
ORDER CODE "P2"
(RELATIVE TO PISTON ROD
AS SHOWN)
CAMERA SENSING OPTION
ORDER CODE "C"
NO SWITCH OPTION
ORDER CODE "N"
27.5
CONFIDENTIAL
2X M10X1.5-6H TAP
THIS DOCUMENT CONTAINS TECHNICAL INFORMATION
PROPRIETARY TO BTM CORPORATION. THE DISCLOSURE
TO OTHERS OR USE OF THIS TECHNICAL INFORMATION,
IN ANY WAY, WITHOUT THE PRIOR WRITTEN CONSENT OF
BTM CORPORATION IS HEREBY EXPRESSLY PROHIBITED.
ALL RIGHTS RESERVED
20.0
R
DO NOT SCALE DRAWING
REMOVE FIRST THREAD FROM ALL TAPPED HOLES.
CUSTOMER
BREAK ALL SHARP CORNERS WITH .020 TO .030 FILLET/RADIUS.
REMOVE ALL BURRS & STAMP OR MARK ALL WITH BTM NUMBER.
SWITCH POSITION 2
STANDARD TOLERANCES
ANGLES
FRAC.
.0
.00
.000
.0000
=
=
=
=
=
=
±0°-30'
±.030
±.06
±.010
±.005
±.0005
UNLESS OTHERWISE SPECIFIED
E5
SHT. SIZE
Titleblock Revised 2012-06-21
GEOMETRIC TOLERANCES TITLE
FLATNESS
STRAIGHTNESS
RUNOUT (CIRCULAR)
PERPENDICULARITY
PARALLELISM
CONCENTRICITY
TRUE POSITION
SCALE
1:1
JOB NUMBER
SHEET
1 / 1
MARYSVILLE, MICHIGAN
U.S.A.
www.btmcorp.com
CORPORATION
BTM STANDARD
XPC LOCKING PIN CLAMP CUSTOMER TEMPLATE
DESIGNED BY
A. SANDERS
BTM No.
TPD275900A350
DETAILED BY & DATE
A. SANDERS
2013-11-20
CHECKED BY & DATE
---------
OPP DETAIL No.
-----
REFERENCE No.
PD275900A350
DATE PRINTED: Wednesday, September 10, 2014
WEIGHT (APPROX)
350 HT = 7.48 kg [16.5 lbs]
650 HT = 10.89 kg [23.6 lbs]
THIS DOCUMENT IS UNCONTROLLED WHEN PRINTED
CYLINDER STROKE: 38.5mm [1.52in.]
BASE MOUNTING
SIDE MOUNTING
MAY BE INSTALLED ON ANY SIDE
WHEN BASE MOUNTED
NOTES FOR BASE MOUNTING:
NOTES FOR SIDE MOUNTING:
Three way shimming simply by bolting
directly to any of available mounting
surfaces. Standard 70 x 70mm bolt
pattern, (4) M10x1.5 tapped holes and
(2) M10 dowel holes
Three way shimming simply by bolting
directly to any of available mounting
surfaces. Standard 70 x 70mm bolt
pattern, (4) M10x1.5 tapped holes and
(2) M10 dowel holes.
SWITCH POSITION 2
ECN No.
REV.
DATE
CHANGE
BY
EC101362
A
2014-01-24
K7 DOWEL FIT WAS H6
ATS
DIMENSIONS
60.0
3X DRAW BOLT
SHCS: M10X1.5 X 50
WITH FLAT WASHER
4.8
137.5
55.0
4.8
5.0 SPACER
NAAMS ASP350
Mount will be opposite proximity switch.
2.5mm ALLOWABLE
ADJUSTMENT
When no switch (NS) or camera
sensing (CS) is chosen, either side of
clamp is available for mounting.
4
Side Mount is NOT available on sides
cylinder can is present.
60.0
137.5
70.0
67.0
55.0
14.8
TYP.
A
2X 10x30 DOWEL
K7 DOWEL FIT
5.0 SPACER
NAAMS ASP350
SWITCH POSITION 1
70.0
4X SHCS: M10X1.5 X 150
WITH FLAT WASHER
2.5mm ALLOWABLE
ADJUSTMENT
110.0 REF.
CLAMP MOUNT
HEIGHT
67.0
12.5
12.0
BOTH CYLINDER CANS
ARE ROTATABLE 360
TO ALLOW PORT ACCESS
IF BLOCKED BY MOUNT
23.2
30.0
5.0 SPACER
NAAMS ACS650
13.0 @5mm SHIM
18.2 @5mm SHIM
XPC ADJUSTABLE MOUNT ORDER INFORMATION
MAY BE INSTALLED ON 2 SIDES
AS SHOWN WHEN SIDE MOUNTED
DESCRIPTION
BTM ASS'Y
NUMBER
XPC: ADJ MOUNT ASSY- 5MM FITTING SPACER
PD281300M
CONFIDENTIAL
THIS DOCUMENT CONTAINS TECHNICAL INFORMATION
PROPRIETARY TO BTM CORPORATION. THE DISCLOSURE
TO OTHERS OR USE OF THIS TECHNICAL INFORMATION,
IN ANY WAY, WITHOUT THE PRIOR WRITTEN CONSENT OF
BTM CORPORATION IS HEREBY EXPRESSLY PROHIBITED.
ALL RIGHTS RESERVED
REMOVE FIRST THREAD FROM ALL TAPPED HOLES.
CUSTOMER
BREAK ALL SHARP CORNERS WITH .020 TO .030 FILLET/RADIUS.
REMOVE ALL BURRS & STAMP OR MARK ALL WITH BTM NUMBER.
ANGLES
FRAC.
.0
.00
.000
.0000
=
=
=
=
=
=
±0°-30'
±.030
±.06
±.010
±.005
±.0005
D
CORPORATION
GEOMETRIC TOLERANCES TITLE
FLATNESS
STRAIGHTNESS
RUNOUT (CIRCULAR)
PERPENDICULARITY
PARALLELISM
CONCENTRICITY
TRUE POSITION
UNLESS OTHERWISE SPECIFIED
SHT. SIZE
Titleblock Revised 18 NOV. 05
R
DO NOT SCALE DRAWING
STANDARD TOLERANCES
SCALE
1:1
JOB NUMBER
-----
SHEET
1 / 1
MARYSVILLE, MICHIGAN
U.S.A.
www.btmcorp.com
BTM STANDARD
XPC: ADJ MOUNT ASSY- 5MM FITTING SPACER
-----
DESIGNED BY
A. SANDERS
BTM No.
TPD281300M
DETAILED BY & DATE
A. SANDERS
2013-09-25
CHECKED BY & DATE
---------
OPP DETAIL No.
-----
REFERENCE No.
PD275800M
DATE PRINTED: Thursday, September 11, 2014
37.0
THIS DOCUMENT IS UNCONTROLLED WHEN PRINTED
150.0
SCR LENGTH