Transcript
62R-SH61R0-0601 English.Spanish.Korean. Traditional Chinese.Japanese. French. German Quick Guide SH61R4 Quick Guide【 English 】 A. Begin Installation 3. Place the rack in the chassis and refasten the rack. For safety reasons, please ensure that the power cord is disconnected before opening the case. Pin Assignments Front Panel 1. Unscrew 3 thumbscrews of the chassis cover. Metal load plate 2. Slide the cover backwards and upwards. F1 F3 F2 USB Header - (USB2) J1 F1.HDD LED 1=5V_USB 3=USB A- 5=USB A+ 7=GND 9=NULL F2.Power Button / Power LED F3.5.25” Bay F4.USB2.0 Ports F5.Microphone Retention tab 2 2=5V_USB 4=USB B6=USB B+ 8=GND 10=NA 1 J3 6 8 3 5 7 2 9 3. Unfasten the rack mount screws and remove the rack. 1 1 2 SPEED_SENSE +12V SPEED_SENSE Ground +12V PWM_CTRL B1 B2 B12 B11 B10 B4 B9 B5 B7 B6 B8 B1.AC Power Socket B2.Kensington Lock B3.Serial Port Perforation (Optional) B4.SPDIF Out Port (Optional) B5.DVI-I Port B6.DVI-D Port B7.USB3.0 Ports B8.Microphone Jack B9.Line-Out Jack B10. Line-In Jack B11. LAN & USB2.0 Ports B12. Clear CMOS Button B13. USB2.0 Ports B14. Wireless LAN Perforation 1=+HD_LED 3=-HD_LED 5=RST_SW 7=GND 9=NA CPU_FAN2 1=Front MIC_L 3=Front MIC_R 5=Head phone_R 7=Front SENSE 9=Head phone_L One PCI Express x1 Slot J4 CPU_FAN ConnectorFAN2 7 5 3 1 10 8 6 4 2 2=AGND 4=Front Audio detect 6=Front MIC SENSE_Return 8=NULL 10=Head phone SENSE_Return 2 3 4 5 6 7 8 9 10 2x USB 2.0 Ports 2x USB 3.0 Ports 2x USB 2.0 Ports J9 COM Header-COM1 J9 J4 1=+12V 2=5V 3=5VSB 4=SERIRQ 5=CLK-48M 6=CLK-33M 7=SIORST# 8=LFRAME 9=LAD3 10=LAD2 Intel H61 Chipset Socket 1155 ATX Power Connector-ATX1 9 2=RX1 4=DTR1 6=DSR1 8=CTS1 10=NULL J5 Power Header-JP3 1 PCI Express 48*2=96 pin 7 5 3 Latch 72*2=144 pin 3. Secure the bracket. 5. Lift the metal load plate on the CPU socket. 1 VGA Card PCB 3 5mm 34.6mm Metal load plate 10 8 6 4 2 3. Check that the latches are closed, and the memory module is firmly installed. Remove the protective membrane 11=-12V 12=3VSB 13=RI 14=LDRQ 15=PME 16=LAD1 17=LAD0 18=+3.3V 19=GND PCI Express x16 slot DDR3 240-pin 1.5V Notch 2 11 12 13 14 15 16 17 18 19 1 2 3 4 5 Read the following precautions before setting up a Shuttle XPC. Laser compliance statement The optical disc drive in this PC is a laser product. The drive's classification label is located on the drive. ATX Power Connector-PWR1 CIR connector -JP6 A DDR3 memory module has a cutout, so it can only fit in one direction. 6 7 8 9 Chassis Cover DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover when the CPU is not installed. 10 PCI Express x16 slots / PCI Repeat the above steps to install additional memory modules, if required. 6. Orientate the CPU and socket, you may align the CPU notches with the socket alignment keys. Make sure the CPU is perfectly horizontal, insert the CPU into the socket. Notch on the CPU/ Alignment Key of the CPU Socket D. Peripheral Installation F. Complete 1. Replace the cover and refasten the thumbscrews. 1. Loosen the purse lock and separate the Serial ATA and power cables. Triangle Pin1 Marking on the CPU Socket 1155 CPU 2. Place the HDD and optical drive in the rack and secure with screws from the side. Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Disposal of used batteries according to the manufacturer's instructions. 2x 240 pins DDR3 DIMM Slots Serial ATA-SATA 1,2,3,4 2. Align the memory module's cutout with the DIMM slot notch. Slide the memory module into the DIMM slot. 2. Install the PCI Express x16 card into the PCI Express x16 slots. CAUTION LPC Header-JP1 FAN Connector-FAN1 1. Unlock the DIMM latch. B LPC Header - (JP1) S/PDIF output Connector -SPDIF1 J3 The maximum size acceptable for display cards is 267mm x 98mm x 34.6mm. A COM Header - (COM1) 1=DCD1 3=TXD1 5=Ground 7=RTS1 9=-XRI DVI-D Port & DVI-I Port 3 One PCI Express x16 Slot This 1155 pin socket is fragile and easily damaged. Always use extreme care when installing a CPU and limit the number of times that you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. 1. Unfasten expansion slot bracket screws. Remove the back panel bracket and put the bracket aside. DDR3 DIMMs are not compatible with DDR/DD2 or DDR DIMMs. Be sure to install DDR3 DIMMs on this motherboard. Follow the steps below to correctly install your memory modules in the memory sockets. 3. Remove the ICE module from the chassis and put it aside. Latch Safety Information J8 Installing a memory module 4. First unlock. Press A with your thumb, then move it to B until it is released from the retention tab and raise the socket lever. 2 E. Accessories Installation C. Memory module Installation Fan Connector 1 Serial ATA Power Cable Follow the steps below to correctly install the CPU into the motherboard CPU socket. 1 Motherboard Illustration FRONT audio Header -JP5 J2 AUX IN ConnectorAUX_IN1 J1 USB Header-USB2 Serial ATA Cable Cutout J8 J6 9 1=Ground 2=5V_DUAL 3=CIR-RX DVI-I & DVI-D Ports cannot be used, if the PCI Express graphics card is installed. Clear CMOS Button 2x USB 2.0 Ports & 1x LAN Line-Out/Line-In Ports/ MIC Port 2=PWR_LED 4=GND 6=PWR_SW 8=GND 10=NULL CIR connector - (JP6) J7 1. Unfasten the ICE fan thumbscrews on the back of the chassis. 12. Fasten the Smart Fan to the chassis with the 4 thumbscrews. 2. Unfasten the four ICE module attachment screws and unplug the fan connector. Front audio Header - (JP5) J6 2 5. Connect the Serial ATA and power cables to the optical drive. Power Header - (JP3) J5 4 Fan Connector Ground FAN1 B14 Serial ATA Cable Serial ATA Power Cable B. CPU and ICE Installation B14 3 3 Back Panel B3 11. Connect the fan connector. 1 2 4. Connect the Serial ATA and power cables to the HDD. 10. Screw the ICE module to the mainboard. Note to press down on the opposite diagonal corner while tightening each screw. Fan Connectors J4 PWM_CTRL B13 9. Tear off the protective membrane from the bottom of ICE module. Remove the protective socket mylar from the CPU socket. 1 1=Ground 2=VCC 3=SPDIF_O 4 3 B14 Load lever 10 S/PDIF Out connector - (SPDIF1) 1=AUX_IN_L 2=Ground 3=Ground 4=AUX_IN_R F4 4 Please do not apply excess amount of thermal paste. AUX IN Connector - (AUX_IN1) J2 F6.Headphone F4 F5 F6 Thermal Paste application area J7 CLASS 1 LASER PRODUCT CAUTION：INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. Serial ATA Optical Drive Notch on the CPU/ Alignment Key of the CPU Socket 2. Complete. Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins on the socket and damage of CPU! 7. Close the metal load plate, lower the CPU socket lever and lock in place. 8. Spread thermal paste evenly on the CPU surface. LThe product’s colour and specification will depend on the actual shipping product. Serial ATA HDD Please press "Del" key while booting to enter BIOS and load the optimised BIOS settings. 53R-SH61R3-2001
