Download GE 22.52 cu. ft. Side-By-Side Refrigerator with LightTouch Dispenser

Transcript
er
or
ne
Ot. Art
8' Ceiling
12"
Soffit
GE Profile Arctica® and GE CustomStyle™ side-by-side installation information & specifications
Rough-in dimensions
13" to 14"
Cabinet
8' Ceiling
FOR 24 CUBIC FOOT MOD
12"
Soffit
Standard, new construction
and replacement installation
13" to 14"
Cabinet
Installation tips to
maximize the built-in look
• All wall/floor molding should be
removed prior to installation.
• Water recess on rear wall
recommended to prevent water line
damage. 48" minimum length,
1/4"-diameter water line tubing
recommended.
• When possible, recess both copper
water line and electrical outlet
(see local codes).
• Front and rear leveling legs are
adjustable for the built-in
1/2" look
(see owner’s manual).
• If optionalAlternate
collar trim kit is to be used
or anticipated,
watersee collar trim
line
installation
onlocation
next page for
through floor
different rough-in
dimensions.
24"
Cabinet
72-1/4"*
25 cu. ft. models
Water hook-up
on the refrigerator
3/4" Airspace
(1/2" Gap + 1/4"
70-1/4"*
Wall Plates)
23 cu. ft. models
72-1/4"*
25 cu. ft. models
25"
Counter
Top
1/2"
Alternate
water
line location
through floor
24-1/2"
Top View
36-1/8"
Installation of water outlets
Electrical
70-1/4"*
23 cu. ft. models
Water hook-up
on the refrigerator
Top View
Water
24-1/2"
36-1/8"
Fig 2A
*The rough-in dimensions of 70-1/4"/72-1/4" are minimum and measured
from eps
the finished floor to top of opening (or the underside of the overhead cabinets).
For Models with Trim Kit: If frameless style cabinets are planned for above the
refrigerator, you may need to consider adding a maximum of 1/4" (70-1/2") to
height of opening for 23 cu. ft. models and 1/8" (72-3/8") for 25 cu. ft. models
to allow additional clearance between cabinet doors and top of refrigerator trim
when cabinet doors are in open position.
*The rough-in dimensions of 70-1/4"/72-1/4" are minimum and measured from
the finished floor to top of opening (or the underside of the overhead cabinets).
For Models with Trim Kit: If frameless style cabinets are planned for above the
refrigerator, you may need to consider adding a maximum of 1/4" (70-1/2") to
height of opening for 23 cu. ft. models and 1/8" (72-3/8") for 25 cu. ft. models Water hook-up
to allow additional clearance between cabinet doors and top of refrigerator trimon the refrigerator
when cabinet doors are in open position.Recommended single loop
Recommended
single loop of 1/4" copper water line
of 1/4" copper water line
1/2"
Allow 48" minimum water
24" line to enable refrigerator
Alternate
water to be pulled forward
line location
through floor
Allow 48" minimum water
line to enable refrigerator 24"
to be pulled forward
18"
IMPORTANT: Before finalizing specifications
for your GE Profile CustomStyle Refrigerator,
please NOTE:
• A minimum width of 36" is required for
refrigerator installation
• Be sure to allow for 1/2" or 3/4" side panels
addition
to the 36" minimum
Collar TriminIn.
w/ceiling
18"
Recommended water line
Recommended water line
Top View
In. w/ceiling
location using recess Collar Trimlocation
using recess
in rear wall
in rear wall
Rear Wall View
Rear Wall View
Create a custom look for your GE Profile CustomStyle side-by-side refrigerator
Water hook-up
on the refrigerator
single loop
Still anotherRecommended
advantage
offered
GE Profile CustomStyle Refrigerators is ease of
of
1/4" copper
waterby
line
installation. For a refrigerator that does so much to enhance the beauty of your kitchen,
the “behind-the-scenes” preparation and installation are surprisingly simple.
Allow 48" minimum water
line to enable refrigerator 24"
to be pulled forward
W3624
Side
Trim
18"
Recommended water line
location using recess
in rear wall
Rear Wall View
In.of water & Electric Ot. Art
WATER
LOCK CONTROL
HOLD 3 SECS
CRUSHED
CUBED
QUICK ICE
DOOR ALARM
LIGHT
RESET WATER FILTER
HOLD 3 SECS
Route
hand slot
before
installing
panel.
1/2" to 3/4" Side Panel
Select appropriate
size door panel from
cabinet line.
Fabricating the enclosure
• The drawing shows an 84" cabinet elevation. Adjust dimensions accordingly for other
cabinet elevations.
• Cabinet pieces to order: (2) side panels and (1) wall cabinet.
• Side panels will typically be attached to adjacent cabinets and/or cleated to rear wall
and floor.
• Refer to GE refrigerator installation instructions for proper plumbing, and electrical and
air clearances.
• (1) Some framed cabinet lines will make a refrigerator enclosure with a cabinet 12" high
x 39" wide with sides and 1-1/2" face frame extended down to floor to create the
refrigerator space. This will replace the above construction. (2) A tall cabinet on either
side of the refrigerator can replace a side panel.
• Counter overhangs on either side of the refrigerator should have clipped corners to allow
for full door swing.
• If the refrigerator has a wall returning beyond the front of the refrigerator on either side,
a 2" tall filler will help allow for movement of the door.
Door Panels
• See drawings for exact dimensions of the fresh-food and freezer door panels.
• Refrigerator door fronts from stock and most semi-custom cabinet manufacturers will
be supplied as 1/4"-thick panels cut to dimensions, with closest available
standard door sizes applied to front.
–This will leave a “reveal” at top/bottom and sides. Width of “reveal” will depend
on manufacturer’s standard door sizes.
–Door will be affixed on the 1/4" panels at factory or in the field by the local
supplier, depending on manufacturer.
• Local shop-built or custom cabinet supplier may fabricate custom 3/4" panels.
In this case, edges must be routed.
• Follow notes on drawing to assure room for fingers/hands to open handles.
24"
Cabin
ge.com
Door panel dimensions (in inches)
23 cu. ft. models
Freezer Panel
Without Dispenser
Cut
out
Freezer Panel
With Dispenser
Cut
out
1/8
5/16
25 cu. ft. models
Fresh Food
Panel
1/8
Freezer Panel
Without Dispenser
1/8
5/16
Cut
out
Cut
out
Freezer Panel
With Dispenser
Cut
out
1/8
5/16
5/16
1/8
14-15/32
17
67-9/32
69
FRONT
FRONT
69
FRONT
FRONT
19-15/32
14-15/32
Freezer panel
with dispenser
FRONT
19-15/32
14-15/32
14-15/32
33-5/8
Freezer panel
without dispenser
36-1/4
Fresh food
panel
Freezer panel
without dispenser
Detail C
Order your own custom wood panels to match cabinetry or other decor.
Panels up to 1/4" thick will fit door frame with no special preparation. Add filler behind
material thinner than 1/4" for proper fit.
Weight Limits: Total weight of panels (i.e., both freezer panels)—Fresh Food = 38 lbs.,
Freezer = 28 lbs.
Note: Panels up to 3/4" will require special routing area around handles.
Dimensions may vary depending on depth of panel.
Freezer panel
with dispenser
Notch required
at top corner
as noted.
1/8"
Fresh food
panel
Panels 1/4" thick
or less
5/16"
1/4" Max.
Fresh Food panel shown
Collar trim installation
1/2" minimum
An enclosure is required to match up to the trim (see Typical Installation). To obtain
the most integrated look, the cabinet or soffit above the refrigerator should extend out
to the same depth as the side panels. The refrigerator opening must have minimum
dimensions of 70-1/4" high x 36-1/8" wide x 24-1/2" deep for 23 cu. ft. models and
72-1/4" high x 36-1/8" wide x 24-1/2" for 25 cu. ft. models, as shown at right. If there is
an overhead cabinet, allow 1" for cabinet door clearance with the top trim piece so the
cabinet doors can be opened without hitting the top trim. If 1/2" side panels are used,
then side trim and panel will be even. If 3/4" side panels are used, then some of the side
panel will extend beyond the trim and must be finished.
70-1/4"*
23 cu. ft. models
IMPORTANT: Before finalizing specifications for your GE Profile CustomStyle
Refrigerator, please NOTE:
• A minimum width of 36-1/8" is required for refrigerator installation with collar
72-1/4"*
25 cu. ft. models
Dr. Panel Dim. Panel 1/4 Thick
24-1/2"
36-1/8"
Dr.
*The rough-in dimensions of 70-1/4"/72-1/4" are minimum and measured from
the finished floor to top of opening (or the underside of the overhead cabinets).
For Models with Trim Kit: If frameless style cabinets are planned for above
Panel
Dim. Detail
C need to consider adding a maximum of 1/4" (70-1/2")
the refrigerator,
you may
to height of opening for 23 cu. ft. models and 1/8" (72-3/8") for 25 cu. ft. models
to allow additional clearance between cabinet doors and top of refrigerator trim
when cabinet doors are in open position.
Refrigerator
Case
3/4" Cabinet
Side Panel
1/2" Cabinet
Side Panel
Collar Trim Installation Art
Typical Installation
Shaded areas represent front surfaces of side panels and
overhead cabinet or soffit that contacts trim.
Overhead
Cabinet
Cabinet
Door
1"
Magnetic
Tape
Door Gasket
Cut
out
5/16
14-15/32
17-7/8
FRONT
1/8
5/16
14-15/32
67-9/32
Fresh Food
Panel
Side Trim
Side trim must be installed
flush with the gasket contact
surface on the case.
Case
Top Trim