Download DT 2-wire User manual
Transcript
DT595A USER MANUAL(EN) 2-Wire Video Intercom System Read this manual carefully before using the product, and keep it well for future use. Parts and Function The door station is an audio door station without camera,which is designed for DT 2-wire system. The front panel is made of zinc alloy for better protection against vandalism & cauterization, and the call button is also made of zinc alloy with blue backlight for auxiliary illumination, the unlock and talking LED indicator guarantee the door station working efficiently. With the rainy cover, the door station can be strongly protection against water. 1 Speaker 2 Unlock Indicator 3 Talk Indicator 4 Front Panel 4 5 Call Button 5 6 Microphone 6 7 Rainy Cover 1 2 7 3 Terminal Description Connection line SPK adjust DIP ON PROG 1 2 3 CALL button 1 2 3 4P terminal 1 2 3 Lock Control Jumper ON 1 2 3 BUS(Blue&Green) S2+(Red) PL(White) S1+(Yellow) S1-(Black) ◆ Lock Control Jumper: to select the lock type. Please refer to Electric Lock Connection ◆ DIP switch: to set ID code for door station, total 4 door stations can be supported. Please refer to DIP Switch Setting. ◆ SPK adjust: to adjust the talk volume. ◆ PROG button: reserve. ◆ CALL button: press to call the user. ◆ 4P terminal: to update software via specified programmer. ◆ Connection line: to connect the bus line and the electronic locks. BUS(Blue&Green): connect to the bus line, no polarity. S2+(Red): the S2+ connect with S1- to activate the relay of ERL to extend a camera of DT-CAM, -3- please refer to DT-CAM user instructions in details. PL(White): external lock power input, connect to the power positive(power +). S1+(Yellow): lock power(+) output. S1-(Black): lock power(-) output. Unit Mounting The location of outdoor station should keep away from snow,rain,and intensity light. Accessory contents: Accessories include a screwdriver T20, one M4X10 screw, two PA4X25 screws,three PA3x25 screws,three PM3x12 screws,and five screw stoppers Φ6X30. Installation steps: Installation height for door station usually is 145~160cm. 1. Use screws to fix the back panel and rainy cover to the wall after connect the cable correctly. 2. Attach the front panel to the back panel, then use the screw to fix it. 1 2 3 PM3*12 M4*10 Wiring and Connection Basic one-to-one connection AC~ PC6 Monitor Bus PL S2+ S1+ S1- + BUS(Blue&Green); S2+(Red); PL(White); S1+(Yellow); S1-(Black); -4- Multi Door Station Connection 4# Camera 3# Camera ID=11 2# Camera 1# Camera ID=10 ID=01 ID=00 ON ON ON ON 12 3 12 3 12 3 12 3 Monitors Bus PL S2+ S1+ S1- Bus PL S2+ S1+ S1- Bus PL S2+ S1+ S1- Bus PL S2+ S1+ S1- AC~ DIP=on,off,off A B C D DBC-4S PC6 OFF ON Impedance Switch BUS(Blue&Green); S2+(Red); PL(White); S1+(Yellow); S1-(Black); Multi Monitors Connection Basic IN-OUT wiring mode ON ON ON ON 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 Code=0, DIP-6=off Code=1, DIP-6=off monitor monitor monitor AC~ PC6 ID=00 ON 12 3 -5- Code=14, DIP-6=off Code=15, DIP-6=on monitor With DBC-4S Wiring Mode ON monitor monitor 1 2 3 4 5 6 Impedance switch Code=14, DIP-6=on A B C D Code=15, DIP-6=on ON 1 2 3 4 5 6 Code=12, DIP-6=on Code=13, DIP-6=on ON 1 2 3 4 5 6 DIP=on,off,off monitor ON monitor Code=2, DIP-6=on Impedance switch A B C D Code=3, DIP-6=on monitor 1 2 3 4 5 6 1 2 3 4 5 6 Code=1, DIP-6=on DIP=on,off,off ON ON monitor OFF ON DBC-4S 1 2 3 4 5 6 ON monitor OFF ON DBC-4S ON 1 2 3 4 5 6 monitor 1 2 3 4 5 6 Code=0, DIP-6=on AC~ PC6 ID=00 ON 12 3 -6- With DT-CAM wiring mode The audio door station DT595A can be extended an additional CCTV camera to be a video door station. For more details about the camera, please refer to DT-CAM user instructions. DT-CAM AC~ ERL OUT IN PC6 DS DT595A Monitor IM Bus PL S2+ S1+ S1- Electric Lock Connection Door Lock Controlled with Internal Power 1 2 3 Connect one lock Note: 1. Electronic lock of Power-on-to-unlock type should be used. 2. The door lock is limited to 12V, and holding current must be less than 250mA. 3. The door lock control is not timed from Exit Button(EB). 4. The Unlock Mode Parameter of Monitor must be set to 0 (by default). Jumper position in 2-3 Bus PL S2+ S1+ S1- *EB LOCK Door Lock Controlled with Dry Contact Take off the Jumper Bus PL S2+ S1+ S1- POWER SUPPLY LOCK -7- Note: 1. The external power supply must be used according to the lock. 2. The jumper must be taken off before connecting. 3. Setup the Unlock Mode of Monitor for different lock types. * Power-on-to-unlock type:Unlock Mode=0 (by default) * Power-off-to-unlock type:Unlock Mode=1 DIP Switch Setting The DIP switch is designed to set the code for door station and monitor, there are two states for each DIP switch, please refer to the following sketch map. ON(1) ON OFF(0) ON = = Door station DIP setting Total 3 bits can be configured, bit-1 and bit-2 are used to assign ID code for door station, bit-3 is used to match the video impedance.The switches can be modified either before or after installation. Bit state Description ON 1 23 ID = 0(00), set to the first door station ON 1 23 ID = 1(10), set to the second door station ON 1 23 ID = 2(01), set to the third door station ON 1 23 ID = 3(11), set to the fourth door station Note: if the video impedance need to match, please set the bit-3 on. Indoor monitor DIP setting There are 6 bits in total. The DIP switches are used to configure the user code for Monitors. Bit-6 is an video impedance match switch, which have to be set to ON if match the impedance, otherwise set to OFF. Bit-1~Bit-5 are used to set user code, to DT595A door station, the user code should set to 0~15. Please refer to the following settings: -8- Bit state ON 1 2 3 4 5 6 User code code=0 ON 1 2 3 4 5 6 ON 1 2 3 4 5 6 ON 1 2 3 4 5 6 ON ON 1 2 3 4 5 6 User code code=6 ON ON 1 2 3 4 5 6 Bit state code=1 code=2 code=3 code=4 1 2 3 4 5 6 ON 1 2 3 4 5 6 ON 1 2 3 4 5 6 ON 1 2 3 4 5 6 Bit state ON 1 2 3 4 5 6 User code code=11 ON code=7 code=8 code=9 code=10 1 2 3 4 5 6 ON 1 2 3 4 5 6 ON 1 2 3 4 5 6 ON 1 2 3 4 5 6 code=12 code=13 code=14 code=15 code=5 1 2 3 4 5 6 Specification • • • • • • Power Supply:DC 24V Power Consumption:Standby 60mA; Working status 200mA Lock Power Supply:12Vdc, 300mA(Internal Power) Working Temperature: -10ºC ~ +45ºC Wiring: 2 wires,non-polarity Dimension:137(H)x49(W)x28(D)mm Precaustions • Please clean the unit with soft cotton cloth, don't use the organic impregnant or chemical clean agent. If necessary, please use a little pure water or dilute soap water to clean the dust. • The unit is weather resistant. However do not spray high pressure water on access control keypad directly. Excessive moisture may cause problems with the unit. • You must use the right adaptor which is supplied by the manufacture or approved by the manufacture. • Pay attention to the high voltage inside the products, please refer service only to a trained and qualified professional. -9- Cable Requirements The maximum distance of the wiring is limited in the DT system. Using different cables may also affect the maximum distance which the system can reach. The farest monitor monitor with two or four monitors monitor monitor DBC-4S B C AC~ PC6 When Monitor quantity < 20 Cable Usage A B C Twisted cable 2x0.75 mm2 60 60 30 80 80 40 A B C 70 30 20 70 50 30 Twisted cable 2x1 mm2 A When Monitor quantity >20 Cable Usage Twisted cable 2x1 mm2 Twisted cable 2x1.5 mm 2 Note:If the monitor has been specified the distance,refer to the parameter. -10- The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved. DT-ENG-595A-V1 P120924 . Right to interpret and copyright of this manual are preserved. Printed 2012. 09 DT-DJ4S Audio Phone User Manual 8888 1 2 Read this manual carefully before using the product, and keep it well for future use. 1. Parts and Functions 97.1 33.2 7 segment LED 187 150 8888 Handset 2 1 Up button Menu button Down button Cancel button Unlock 2nd button Unlock button Speaker Handset line Side View Key functions 7 segment LED Display setting informations Handset Pick up to communicate with visitor Hand line Connect handset with monitor Unlock button Press to release the door Unlock 2nd button Press to release the second door Up button Press to move up or increase the value Down button Press to move down or decrease the value Menu button Press and hold for 2s to open the setting menu shortcuts. Cancel button Press to cancel the operations Speaker Send out voice from the visitor 2. Operation Instructions 1) Door opening function: When visitor calls from outdoor station, the monitor rings, pick up handset to talk with the visitor, then press the Unlock button to open the door. If the system connect 2 locks,press Unlock 2nd button to open the second door. 2) Monitoring & calling menu: Pick up handset in standby mode,the LED will be shown a scroll information “Intr Call”,pressing Up button or Down button can stop the scroll. To quit this menu, please tap Cancel button. 3) Entrance monitoring: In monitoring & calling menu page, the LED show "dsx"(x=1~4,refer to part 3-Numbers of door station),it means that the monitor select "x" door station to monitor. Press Up / Down button to increase/decrease the value,then press Menu button to activate the monitoring. 4) Inner call: In monitoring & calling menu page, use Up / Down button to select "-ALL" item on LED,then press Menu button to activate the inner call,all monitors connected to the system will ring at the same time. Pick up any monitor,the others will stop ringing immediately.(note that the user code must be the same for all monitors to activate the inner call function) 5) Intercom call: In monitoring & calling menu page, use Up / Down button to select "C-xx" (xx=00~31,refer to part3-Numbers of indoor monitor)item on LED,then press Up / Down button to increase/decrease the value,and press Menu button to confirm the intercom calling.(note that the user code must be different for all monitors to activate the intercom call function) 3. Setup Instructions Press Menu button and hold for 2s in standby mode,the LED will be shown a scroll information "User Set-",press Up button or Down button to stop the scroll,and the LED show the setting items. Press Menu button to select next setting items. To quit this setting menu, please tap Cancel button. Setting Item Door station call tone Intercom call tone LED state Description Default 1-xx Set the ring tone calling from outdoor station. Total 12 pieces ring tones can be selected(xx=01~12),press Up button or Down button to increase/decrease the value,settings will be performed immediately. 02 2-xx Set the ring tone calling from intercom call or inner call. Total 12 pieces ring tones can be selected(xx=01~12), press Up / Down button to increase/decrease the value, settings will be performed immediately. 12 Setting Item LED state Description Default Door bell call tone 3-xx Set the ring tone calling from door bell. Total 12 pieces ring tones can be selected(xx=01~12),press Up button or Down button to increase/decrease the value,settings will be performed immediately. 02 Ring volume 4-rx Set the ring volume for call tone,range from 0~9. 6 5-0x Maximum 4 door stations can be selected,this item is used to set the numbers of door station that can be surveilled by indoor monitor. Refer to part 2 ->Entrance Monitoring. 1 Numbers of indoor monitor 6-xx Maximum 32 indoor monitors can be selected,this item is used to set the numbers of indoor monitor that can be selected to intercom. Refer to part 2 ->Intercom call. 04 Slave address setting for monitor 7-dx Rang from 0~3,"0"-master monitor,"1~3"-slave monitor. 0 8-FS The restore to default function allows the user to recover the settings to factory setting. Select "8FS" item on LED,then press Up button,"yES"will be asked,press Up button again,the LED will be shown"SUCC",that means settings are restored to default. - Numbers of door station Restore to default setting 4. Specification ●● ●● ●● ●● ●● Power Supply: Power Consumption: 7 segment LED: Wiring: Dimension: DC24V standby 25mA,working 110mA 4 digits dynamic 2 wires, non-polarity 187(H)X97(W)X33(D)mm The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.