Download Vibe Monobox III Instruction manual

INSTRUCTION
MANUAL
Slick SLR 12 Active
Subwoofer Enclosure
Model: SLR12A LIMITED EDITION
www.vibeaudio.co.uk
To ensure maximum
performance and safety,
please follow this manual.
Please retain the manual
for future reference after
installation
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
OWNERS MANUAL
Congratulations on purchasing your VIBE SLR subwoofer enclosure, please read this manual in
order to fully understand how to get the best results from this w and ensure that all advice on how
to look after the subwoofer is followed.
Thank you for buying VIBE, we hope you enjoy listening to your product as much as we enjoyed
creating it.
VIBE R&D Division
WARNING
DO NOT EXPOSE THIS PRODUCT TO DAMP OR MOISTURE - doing so may result in fire,
shock or damage to the product.
BEFORE WIRING DISCONNECT THE CABLE
BLE F
FROM THE POSITIVE BATTERY TERMINAL
- failure to do so may result in electric shock
ock or injury.
inju
ENSURE GOOD AND CORRECT CONNECTIONS
ONNECTIONS - failure to make the correct connections
may result in fire or damage to the product.
roduct.
KEEP THE VOLUME AT A LEVEL
EL SO YOU CAN STILL HEAR OUTSIDE NOISE - failure
to do this may result in an accident.
ident. VIBE
V E equipment
equipment is capable
ca
of producing sound levels
that can permanently damage your hearing.
he ng. VIBE recommends
r ommend caution when listening at high
volume. For safe and enjoyable
able listening
g the sound should be comfortable and clear without
distortion.
CAUTION
• Never connect any speaker
peaker lead to the car chassis.
chass This can cause severe
s
damage to your
speaker / car radio / amplifier.
• Before drilling or cutting any holes, investigate
stigate the
th layout of your vehicle thoroughly.
en working near the fuel / hydraulic
hydrau lines and electrical wiring.
wir
• Use caution when
• Observe the correct
orrect polarity when wiring,, improper
improp phasing may cause a loss
lo of bass
response.
• Ensure thatt no moving parts catch on the speaker
or grill (e.g. window or door handles, or
spea
window glass
lass inside
ins
the door)
INSTALLATION
ALLAT
• The quality of the installation will affect the system performance and reliability.
• Contact
ntact your
yo nearest authorised VIBE dealer if you
yo are unsure about the installation
llation of this
product.
• Please mount this unit away from any potential hazards.
• Minimising the length of wires will provide higher audio output from the system.
• The speaker should be securely fastened to the mounting position using the screws provided.
• Pre drill your mounting holes using a drill and position with the template provided.
• Be sure to investigate your mounting area thoroughly for electrical wires, brake or fuel lines
or fuel tank to prevent causing any damage.
2
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
RUN IN PROCEDURE
VIBE recommends that you follow the run in procedure for the subwoofer detailed below.
When your subwoofer is used for the first time it is very stiff and rigid, it will take time for the moving
parts of this subwoofer to loosen up before it will be ready to deliver its full potential.
For the first 30 hours it is recommended that you play the subwoofer initially at low to medium
volumes, gradually increasing the volume level as time progresses. As a guide, if you listen to it for
1 hour every day it will take a month for the speaker to run in properly. You will notice a big change
in the sound of the subwoofer over this period, as the spider and surround begin to run in the sound
will get deeper and punchier, also the output of it will increase as the suspension loosens up.
A new subwoofer is like a new car engine, it needs a few thousand miles before you can drive it to
its full potential, driving it into the ‘red line’ from the first day will mean engine damage is certain and
will not be covered by warranty and the same applies to the subwoofer. Failure to follow this simple
procedure is the most common reason for a subwoofer to fail after a very short period of time.
INSTALLATION
The most common place to mount a bass enclosure is in the luggage compartment of the vehicle.
Where in the luggage compartment it is mounted will have an effect on the sound produced allowing
the user to tailor the sound to best suit their musical tastes. For example if the enclosure is mounted
facing the rear bumper, the bass produced will be noticeably deeper than if it is fired into the rear
seat.
Do not be afraid to experiment with positioning as a little time and effort can yield great improvements
in sound.
3
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
ACTIVE ENCLOSURE INSTALLATION
Your VIBE SLR enclosure is designed with a swift installation routine in mind. Please mount the
enclosure in a dry location on a solid surface. NEVER mount the enclosure upside down, this will
cause the amplifier to overheat and will eventually damage the amplifier. Before fixing the enclosure
in place please ensure that there is sufficient air flow around the amplifier heatsink, at least two
inches will be sufficient.
POWER CABLE
• At least a 10 gauge cable should be used for both the power and the ground connections to
the amplifier.
• The power cable should be taken directly from the battery. Rubber grommets should be used
when passing through any bulkheads to prevent the cable from becoming chaffed or cut.
• It is vital that a fuse / circuit breaker (of at least equal value to the one fitted on the amplifier)
is placed in line with the power cable and is no further than eighteen inches away from the
battery.
• Please ensure that the fuse is not fitted until the entire installation procedure is complete.
• The two tables below are to help you decide on what cable is correct for you. The first enables you to select the size of cable depending on the length required. The second will help
you convert the cable size from American Wire Gauge to Metric if you need to.
Current demand
0–20 amps
20–35 amps
35–50 amps
50–65 amps
65–85 amps
85–105 amps
105–125 amps
125–150 amps
0 – 4 Ft
14
12
10
8
6
6
4
2
A
AWG
Number
0
1
2
3
4
5
6
7
8
9
10
4
4 – 7 Ft
12
10
8
8
6
6
4
2
Length of Run
7 – 10 Ft
10 – 13 Ft 13 – 16 Ft
12
10
10
8
8
6
8
6
4
6
4
4
4
4
2
4
2
2
4
2
0
2
0
0
1Metre–3.28Feet
A
AWG
to Metric Conversion Chart
cross sectional area
Inch
mm
0.325
0.289
0.258
0.229
0.204
0.182
0.162
0.144
0.128
0.114
0.102
8.25
7.35
6.54
5.83
5.19
4.62
4.11
3.66
3.26
2.91
2.59
16 – 19 Ft
8
6
4
4
2
2
0
0
mm2
53.5
42.4
33.6
26.7
21.1
16.8
13.3
10.5
8.36
6.63
5.26
19 – 22 Ft
8
6
4
4
2
2
0
0
22 – 28 Ft
8
4
4
2
0
0
0
0
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
GROUND CABLE
• The ground cable needs to carry the same current as the power cable. At least a 10 gauge
cable should be used.
• The amplifier ground should be connected directly to the chassis of the vehicle, to bare
metal.
• The cable length should be kept to an absolute minimum. It is not recommended that you
connect the ground cable to the vehicle’s seatbelt anchor point.
REMOTE TURN ON
• A minimum of 18 gauge cable should be used for this connection.
• The cable should be run with exactly the same care and attention as the power cable and
taken back to the source (headunit) and joined to the remote cable provided.
• If the source (headunit) does not have a remote turn on cable then a 12v supply should be
used. This will require a switch to be fitted inline to enable the amplifier to be turned on and
off. Remember that if this switch is left on you will flatten the car battery.
RCA CABLES
• Please take extra care when running these cables from the source to the amplifier. Ensure
that they are placed away from all items that can generate any interference, wiring harnesses etc.
• It is recommended that the RCA cables should be run on the opposite site of the car to any
previously installed power cables, if possible.
INPUT CONNECTIONS
Connect to
chassis / ground
of vehicle
FUSE
BATTERY
Connect to remote turn-on
lead of source unit
SOURCE (HEAD UNIT)
5
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
AMPLIFIER CONNECTIONS & CONTROLS
F
G
D
E
C
A
B
H
A. LOW LEVEL INPUT
Low level input for connection to any source (headunit) with a low level output. This is your RCA
output from the source (headunit).
B. HIGH LEVEL INPUT
To be used when no RCA’s are available. Use the provided loom to connect to the closest
speakers.
C. GAIN CONTROL
Used to match the input signal of the source (headunit) to the amplifier. See the setup section for
more details.
D. CROSS OVER FREQUENCY CONTROL
High pass frequency control. The frequency ranges from 50 Hz to 250 Hz.
E. BASS BOOST CONTROL
To provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output
from the amplifier.
F. FUSE
Please ensure the following fuse rating is used when replacing fuses:
SLICK SLR12A (20 amp)
G. POWER CONNECTIONS
Power connections. See input connections section for details on correct connections.
H. POWER PROTECT LIGHT
When the amplifier is operating correctly the light will illuminate constant ‘white’. When the amplifier
is in power protecttion mode the light will illuminate ‘red’.
6
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
SETUP SECTION
To correctly set the gain control of the amplifier to match that of the source (headunit) use the
following setup routine:
• Turn the gain control to minimum on the amplifier.
• Ensure the bass boost is set to 0 dB.
• On the headunit set all crossovers to flat and both bass and treble to zero.
• Turn up the source (headunit) to approx 3/4 volume.
• Very slowly turn up the gain on the amplifier until distortion can be heard in any of the speakers or until the volume reaches an uncomfortable listening level when this is reached turn
down the gain control slightly.
• The gain control is now set.
The setting of the crossover will directly effect the sound you will hear from the subwoofer. At its
lowest setting (50 Hz) the subwoofer will only react to frequencies from around 35 Hz to 50 Hz. At its
highest setting (250 Hz) the subwoofer will react to a larger range of frequencies from around 35 Hz
to 250 Hz. Experiment with this setting to achieve a sound you are happy with that feels comfortable
with the music that you listen to.
7
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
TROUBLESHOOTING
Before removing the amplifier, refer to the list below and follow the suggested procedure. Always
test the speakers and confirm that they are wired correctly first. If in any doubt get help from a
qualified auto electrician.
AMPLIFIER WILL NOT POWER UP
• Check for good ground connections. Ensure that the ground cable is connected directly to
bare metal and not a painted surface.
• Using a multimeter check the that remote terminal has at least 7V DC.
• Using a multimeter check that there is battery voltage on the positive terminal.
• Check all fuses.
• Check that the protection light is not illuminated. If it is lit, shut off the amplifier for thirty
seconds and then turn it back on.
PROTECTION LED ILLUMINATES WHEN AMPLIFIER IS POWERED UP
• The amplifier is designed to shut down automatically when the units temperature goes above
80 degrees. If the amplifier feels very hot then this may be the reason for the amplifier not
starting.
• Check that there is good airflow around the amplifier. In some applications an external fan
may be required.
BLOWN FUSE(S)
• Check both positive supply and ground for shorts.
• Check that the positive wire is connected to the positive terminal on the amplifier.
• Check that the negative wire is connected to the ground terminal on the amplifier.
• Ensure that the correct rated fuse is fitted:
SLICK SLR12A (20 amp)
DISTORTED SOUND
• Check the gain control is not set at too high a level. If the sound is distorted turn the down
the gain until the sound is clear.
• Check that all crossover frequencies are correct. See setup section for more details.
• Check that the ground cable is making good contact with the vehicle chassis.
• Check the the RCA cables are making good connection with the source and amplifier.
8
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
LIMITED WARRANTY
All VIBE products carry a full 12 months warranty, valid from the date of the original receipt and
proof of purchase. In order to validate this warranty, the warranty card should be returned to VIBE
within seven days of the original purchase date. The original receipt and packaging are should
also be retained for this twelve month period. If at any stage during the warranty period you have a
problem with the product then it should be returned to the point of purchase, in its original packaging,
complete with no items missing. If the store is unable to fix the product it may have to be returned to
VIBE this process takes around 7 working days and no costs will be occurred.
A full description of VIBE’s warranty information can be found on our website:
WWW.VIBEAUDIO.CO.UK/WARRANTY
WHAT IS NOT COVERED
● Damage to product due to improper installation
● Subsequent damage to other components
● Damage caused by exposure to moisture, excessive heat, chemical cleaners and/or UV
radiation
● Damage through negligence, misuse, accident or abuse, repeated returns for the same fault
may be considered abuse
● Any cost or expense related to the cost of removal or re-installation of the product
● Damage caused by amplifier clipping or distortion
● Items repaired or modified by any unauthorized repair facility
● Return shipping on non defective items
● Products returned without a returns authorization number
● Damage to product due to the use of sealant
INTERNATIONAL WARRANTY
Contact your International VIBE audio dealer or distributor concerning specific procedures for your
country’s warranty policies.
WARNING
VIBE subwoofers are capable of sound pressure levels that can cause permanent damage to your
hearing and those around you. Please use common sense when listening to your car audio system
and practice safe sound.
COPYRIGHT
All content included in this manual such as text, graphics, logos, icons, images and data, are the property of VIBE Technologies Limited (herein referred to
as “VIBE”, “us” or “we”) and its affiliate or their content and technology providers, and are protected by United Kingdom and International copyright laws. All
rights reserved. VIBE Turbo Port, Vibe TurboVent, Pressure Board, Super Driver, VIBE Pulse, VIBE Power, VIBE Digital, VIBE MAG Plugs, Ferrite Loaded,
VIBE Solid Core, VIBE OCC, VIBE FLAT, BlackAir, BlackBox, Space, MonoBox, SA-K, SR, QB69, ICC, Bass Enhance, Bass Enhance+, QBass, SpeedBass,
PowerBass and all stylised representations of product names, or the abbreviations of product names, as logos are all trademarks of VIBE. Graphics and logos
are trademarks or trade dress of VIBE Technologies Ltd or its subsidiaries. VIBE’s trademarks and trade dress may not be used in connection with any product
or service that is not VIBE’s, in any manner that is likely to cause confusion among customers or in any manner that disparages or discredits VIBE. All other
trademarks not owned by VIBE or its subsidiaries that appear in this manual are the property of their respective owners, who may or may not be affiliated with,
connected to, or sponsored by VIBE or its subsidiaries.
TO THE FULLEST EXTENT PERMITTED AT LAW, VIBE IS PROVIDING THIS MANUAL AND ITS CONTENT ON AN “AS IS” BASIS AND MAKES NO (AND
EXPRESSLY DISCLAIMS ALL) REPRESENTATIONS OR WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WITH RESPECT TO THIS MANUAL
OR THE INFORMATION, CONTENT, MATERIALS OR PRODUCTS INCLUDED IN THIS MANUAL INCLUDING, WITHOUT LIMITATION, WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN ADDITION, VIBE DOES NOT REPRESENT OR WARRANT THAT THE
INFORMATION CONTAINED IN THIS MANUAL IS COMPLETE OR CURRENT, AND THAT ALL SPECIFICATIONS AND INFORMATION CONTAINED
WITHIN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. VIBE RECOMMEND CAUTION WHEN LISTENING TO MUSIC REPRODUCED
THROUGH VIBE EQUIPMENT. VIBE EQUIPMENT IS CAPABLE OF PRODUCING SOUND AND SOUND PRESSURE LEVELS THAT CAN PERMANENTLY
DAMAGE HEARING OF YOU AND THAT OF OTHERS. FOR SAFE AND ENJOYABLE LISTENING, THE SOUND SHOULD BE CLEAR WITHOUT
DISTORTION AT A COMFORTABLE VOLUME. BY USING ANY VIBE EQUIPMENT, YOU AGREE TO TAKE FULL RESPONSIBILITY FOR YOUR OWN
SAFETY AND THE SAFETY OF OTHERS WHEN LISTENING TO MUSIC AT HIGH VOLUMES THROUGH EQUIPMENT YOU HAVE PURCHASED. USE OF
ANY VIBE EQUIPMENT CONSTITUTES AGREEMENT TO THIS DISCLAIMER.
Except as specifically stated in this manual, to the fullest extent permitted at law, neither VIBE nor any of its affiliates, directors, employees or other
representatives will be liable for damages arising out of or in connection with the use of this manual or the information, content, materials or products included.
This is a comprehensive limitation of liability that applies to all damages of any kind, including (without limitation) compensatory, direct, indirect or consequential
damages, loss of data, income or profit, loss of or damage to property and claims of third parties. For the avoidance of doubt, VIBE does not limit its liability for
death or personal injury to the extent only that it arises as a result of negligence of VIBE, its affiliates, directors, employees or other representatives.
9
Slick SLR 12 Active Limited Edition Subwoofer Enclosure
SPECIFICATIONS
SLICK SLR12A
RMS Power
Peak Power
400 Watts
1200 Watts
In order to protect your purchase and aid your warranty please fill
in the following form and keep it safe for your future reference.
For more information and to register your warranty online, visit:
www.vibeaudio.co.uk/warranty
MODEL NUMBER:
SERIAL NUMBER:
PURCHASED FROM:
KEEP IT SAFE
10
Staple your receipt here:
DATE OF PURCHASE:
+PJO7*#&POMJOF
twitter.com/vibeaudio
youtube.com/vibeaudio