Download Craftsman 917.25022 Operator`s manual
Transcript
Operator's Manual cRn I n#° II III LAWN TRACTOR 21.0 HR* 42" Mower Electric Start 6 Speed Transaxle Model No. 917.25022 • EspaSol, p. 31 _ This product has a low emission engine which operates differently from previously built engines, Before you start the engine, read and understand this Operator's Manual. IMPORTANT: Read and follow all Safety Rules and Instructions before operating this equipment. For answers to your questions about this product, Call: 1-800-659-5917 Sears Craftsman Help Line 5 am - 5 pm, Mon - Sat Gasoline containing up to 10% ethanol (El0) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (El0) wil! void the product warranty. Esta m&quina puede utilizar gasolina con un contenido de haste el 10% de etanol (El0). El uso de una gasolina qua supere el 10% de etanol (El0) anular6 la garantie del producto, Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A. Visit our Craftsman website:www.sears.com/craftsman *As rated bytheengine manufacturer 446645 Warranty .................................................. 2 Safety Rules ............................................ 3 Product Specifications ............................. 6 Assembly/Pre-Operation ......................... 7 Operation ................................................. 9 Maintenance .......................................... 15 Maintenance Schedule .......................... t5 Service and Adjustments ....................... 19 Storage .................................................. 25 Troubleshooting ..................................... 26 Sears Service .......................... Back Cover Craftsman Riding Equipment Warranty CRAFTSMAN FULL WARRANTY FOR TWO YEARS from the date of purchase, all non-expendable parts Ofthis ridingequipment are warranted against any defects in material or workmanship. A defective non-expendable part will receive free in-home repair or replacement if repair is impossible. FOR FIVE YEARS from the date of purchase, the frame and front axle of this riding equipment are warranted against any defects in material or workmanship. A defective frame or front axle will receive free in-home repair or replacement if repair is impossible. FOR 90 DAYS from the date of purchase, the battery (an expendable part) of this riding equipment is warranted against any defects in material or workmanship (our testing proves that it will not hold a charge). A defective battery will receive free in-home replacement. ADDITIONAL LIFETIME LIMITED WARRANTY on CAST IRON FRONT AXLE (if equipped) FOR AS LONG AS IT IS USED by the original owner after the fifth year from the date of purchase, the cast iron front axle (if equipped) of this riding equipment is warranted against any defects in mateda] or workmanship. With proof of purchase, a defective cast front axle will receive free in-home replacement. WARRANTY SERVICE For warranty coverage details to obtain free repair or replacement, call 1-800-659-5917 or visit the web site: www.craftsman.com In alI cases above, if part repair or replacement is impossible, the riding equipment wilt be replaced free of charge with the same or an equivalent model. All of the above warranty coverage is void if this riding equipment is ever used while providing commercial services or if rented to another person. This warrantycovers ONLYdefects in material and workmanship.Warranty coverage does NOTinclude: • Expendable parts (except battery) that can wear out from normal use within the warranty period, including but not limited to blades, spark plugs, air cleaners, belts, and oil filters. - Standard maintenance servicing, oil changes, or tune-ups. • Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass. • Tire or wheel replacement or repair resultingfrom normal wear, accident, or improper operation or maintenance. ° Repairs necessary because of operator abuse, including but not limited to damage caused by towing objects beyond the capability of the riding equipment, impacting objects that bend the frame, axle assembly or crankshaft, or over-speeding the engine. • Repairs necessary because of operator negligence, including but not limited to, electrical and mechanical damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the riding equipment according to the instructions contained in the operator's manual. • Engine (fuel system) cleaning or repairs caused by fuel determined to be contaminated or oxidized (stale). In general, fuel should be used within 30 days of its purchase date. • Normal deterioration and wear of the exterior finishes, or product label replacement. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears Brands Management Corporation, Hoffman Estates, IL 60179 _DANGER: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. _WARNING: In order to prevent accidental starting when setting up, transporting, adjustingor making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. • Never direct discharged materialtoward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces. • Do not operate machine without the entire grass catcher, discharge chute, or othersafety devices in place and working. • Slow down before turning. • Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. • Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge chute. ° Operate machine only indaylight or good artificial light. • Do not operate the machine while under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways. • Useextra carewhen loading or unloading the machine into a trailer or truck. • Always wear eye protectionwhen operating machine. • Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and othersfrom serious injury. ° Followthe manufacturer's recommendation for wheelweights or counterweights. • Keep machine free of grass, leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower to plow leaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage. _kWARNING: Do not coast down a hill in neutral, you may lose control of the tractor. _[_WARNING: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor, _WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm, ,_WARNING: Battery posts,terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. I. GENERAL OPERATION • Read, understand,and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. ° Only allow responsible adults, who are familiar with the instructions, to operate the machine. ° Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades. ° Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area, • Never carry passengers. • Do not mow in reverse unless absolutely necessary, Always Iookdown and behind before and while backing. 8 II, SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or ifyoufeel uneasy on it, do not mow it. • Mow up and down slopes, not across, • Watch for holes, ruts, bumps, rocks, or other hidden objects, Uneven terrain could overturn the machine. Tall grass can hide obstacles. Choose a low ground speed so that you will not have to stop or shift while on the slope. • Do not mow on wet grass. Tires may lose traction. Always keep the machine in gear when going down slopes. Donot shiftto neutral and coast downhill, • Avoid starting, stopping, or turning on a slope, lfthetireslosetraction, disengage the blades and proceed slowly straight down the slope, • Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over. • Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine, Do no use on steep slopes. • Do not try to stabilize the machine by putting your foot on the ground. • Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in. !11.CHILDREN _WARNING: CHILDREN BY THIS EQUIPMENT. The - Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. • Be alert and turn machine off if a child enters the area. • Before and while backing, look behind and down for small children. • Never carry children, even withthe blades shutoff. They mayfaUoffand be seriously injured or interfere with safe machine operation. Children who have been given rides inthe past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine. • Never allow children to operate the machine, • Use extra care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child, IV. TOWING • Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. • Followthe manufacturer's recommendation for weight limits for towed equipment and towing on slopes. • Never allow children or others in or on towed equipment. • On slopes, theweight of the towedequipment may cause loss of traction and loss of control. • Travel slowly and allow extra distance to stop. V. SERVICE SAFE HANDLING OF GASOLINE To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive, • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Use only approved gasoline container. • Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. . Never fuel the machine indoors. • Neverstorethe machine orfue]container where there is an open flame, spark, or pilot light such as on a water heater or other appliances. • Never fill containers inside a vehicle or on atruck or trailer bed with plastic liner. Always place containers on the ground away from your vehicle when filling. CAN BE INJURED American Academy of Pediatrics recommends that children be a minimum of 12 year of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of age before operating a riding lawn mower. Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. 4 • Remove gas-powered equipment from • thetruckortrailerandrefuel itonthe ground. Ifthis[snotpossible, thenrefuel • such equipment withaportable container, rather thanfroma gasoline dispenser nozzle. • Keep thenozzle incontact withtherim • ofthefueltankorcontainer opening at alltimes untilfueling iscomplete. Donot useanozzle lock-open device. • • iffuelisspilled onclothing, change clothingimmediately. • • Never overfill fueltank.Replace gascap andtighten securely. GENERAL SERVICE • • , Never operate machine in a closed area, Keep all nuts and boltstightto be surethe equipment is in safe working condition. Maintain or replacesafety and instruction labels, as necessary. o Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area, • Never carry passengers. • Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing, • Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides inthe past maysuddenly appear in the mowing area for another ride and be run over or backed over by the machine. • Keep children out of the mowing area and inthe watchful care of a responsible adult other than the operator. • • ° • Never tamper with safety devices. Check their proper operation regularly. Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove anyfuel-soaked debris, Allow machineto coot before storing. If you strike a foreign object, stop and inspectthe machine. Repair,ffnecessary, before restarting. Never make any adjustments or repairs with the engine running. Checkgrass catcher components andthe discharge chute frequently and replace with manufacturer's recommended parts, when necessary. Mowerbladesaresharp, Wraptheblade or wear gloves, and use extra caution when servicing them. Check brakeoperationfrequently. Adjust and service as required. Be alert and turn machine off if a child enters the area. Before and while backing, look behind and down for small children. Mow up and down slopes (15° Max), not across, ° • • • • Choose a low ground speed so that you will not have to stop or shift while on the slope. Avoid starting, stopping, or turning on a slope, lfthetires Iosetraction, disengage the blades and proceed slowly straight down the slope. If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. When loading or unloading this machine, do not exceed the maximum recommended operation angle of 15°, PRODUCT SPECIFICATIONS Gasoline Capacity and type: 2.50 Galtons19,46 L Regular Unleaded Oit Type: _PI: SG-SL) SAE 30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C Oil Capacity: WJ Filter: W/out Filter: Spark Plug: Champion RC12YC (Gap: .030"/0,75 ram) Ground Speed (Mph/Kph): Forward: Reverse: 56 Oz.!1,65 L 48 OzJ1,4 L 1st 2nd 3rd 4th t,0/1,6 1,4/2,3 2,1/3,4 3,1/5,1 5_h 4.0/8,4 6th 5.4/8,2 0 - 2.9/4,7 Charging System: 3 Amps Battery 5 Amps Headlights Battery: Amp!Hr: Min. CCA: Case size: Blade Bolt Torque: 45-55 Ft, LbsJ62-75 28 230 U1R In the state of Ca[ffomiathe above is required by law (Section 4442 ofthe California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearestSears service center (See REPAIR PARTS manual). REPAIR PROTECTION AGREEMENTS Congratulations on making a smart purchase. Your new Craftsman@ product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you money and aggravation. Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense. Here's what's included in the Agreement: Nm CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience anyproblem you cannot easily remedy, please contact a Sears or other qualified service center. We have competent, well-trained representatives and the proper tools to service or repair this tractor. Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly. Always observe the "SAFETY RULES". CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. o Foliow a regular schedule in maintaining, caring for and using your tractor, • Follow instructions under "Maintenance" and "Storage" sections of this manual. ° Wear proper Personal Protective Equipment (PPE) while operating this machine, including (at a minimum) sturdy footwear, eye protection, and hearing protection. Do not mow in shorts and/or open toed footwear. • Always let someone know you are outside mowing. _JlLWARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine's exhaustsystem is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. • • Expertservice byour 12,000 professional repair specialists. Unlimited serviceand no chargefor parts and labor on all covered repairs. • Product replacement if your covered product can't be fixed. • Discount of 10% from regular price of service and service-related parts not covered bythe agreement; also, 10% off regular price of preventive maintenance check. • Fast help by phone - phone support from a Sears representative on products requiring in-home repair, plus convenient repair scheduling. Onceyou purchasethe Agreement, asimple phone calt is all that ittakes for you to schedule service. Youcan cattanytime day or night, or schedule a service appointment online. Sears has over 12,000 professionalrepair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today! Some limitations and exclusions apply. For prices and additional information call 1-800-827-6655. SEARS INSTALLATION SERVICE For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U.S.A, call 1-800-4-MY-HOME@ Keys Slope Sheet (2) Keys i,iiiL.J.llu JJJlJH ILLuJu,i .JLiii i/i/iLlLI/i H/i/ i1_/ii ill i i Your new tractor has been assernbledat the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) 1/2" wrench (2) 7/t 6" wrenches Pliers Tire pressure gauge Utility knife When right or left hand is mentioned in this manual, itmeanswhenyou areintheoperating position (seated behind the steering wheel). ADJUST SEAT 1, Sit in seat. 2. Liftup adjustment lever (A) and siide seat until a comfortable position is reached which allows you to press clutch!brake pedal a]] the way down, 3. Release lever to lock seat in position. TO REMOVE TRACTOR FROM CARTON UNPACK CARTON • Remove all accessible loose parts and parts cartons from carton. • Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat. o Check for any additional loose parts or cartons and remove, BEFORE REMOVING TRACTOR FROM SKID TO CHECK BATTERY 1. Lift seat to raised position, NOTE: If this battery is put intoservice after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-I0 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions). , For battery and battery cable installation see "REPLACING BATTERY" in the "Service and Adjustments" section in this manual. NOTE: You may now roll your tractor off the skid. Foliow the appropriate instruction below to remove the tractor from the skid. Al_WARNING: Before starting, read, understand and follow all instructions in the Operation section ofthis manual. Ensuretractoris in a well-ventilated area, Ensurethearea in front of tractor isclear of other people and objects. 7 TO ROLL TRACTOR OFF SKID t/f (See Operation section for location and function of controls) 1. Raise attachment lift lever to its highest position. 2. Release parking brake by depressing clutch/brake pedal. 3. Place gearshift lever in neutral position. 4. Roll tractor forward off skid. 5. Remove banding holding the deflector shield up against tractor. Continue with the instructionsthat follow. I/El asiento ha side ajustado en forma c6moda y apretado en forma segura. ,/Todas Ias tlantas han side infladas en forma adecuada. (Para fines de envio, Ias Ilantas se inflaron demasiado en Ia f&bdca.) v( Asegt3rese que el conjunto segador est_ nivelado en forma adecuada, de lade a lade y desde adelante hacia atr&s, para obtener los mejores resultados en el corte. (Las ]lantas tienen que estar infladas en forma adecuada para la nivelaci6n.) V_ Revise las correas de imputsi6n y de la segadora. Asegt_rese que recorran el paso adecuado alrededor de fas poleas y dentro de lodes los fijadores de las correas. J Revise el alambrado. Fijese que todas ]as conexiones todavia est6n seguras y que los atambres est6n sujetos en forma adecuada. CHECK TIRE PRESSURE Thetires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK For best should be MOWER" section of cutting results, mower housing properly leveled. See"TO LEVEL in the Service and Adjustments this manual. LISTA DE REVISION Antes de operary de disfrutar de su tractor nuevo, le deseamos que reciba el mejor rendimiento y [a mayor satisfaccion de este preducto de calidad. Haga el favor de revisar ta lista a continuacion; J Se ban comp]etado todas las instrucciones de montaje. vt Noquedan partessueltas en la caja de cart6n. J La bater{a est& preparada y cargada en forma adecuada. LEVELNESS CHECK FOR PROPER POSITION OF ALL BELTS See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly. CHECK BRAKE SYSTEM After you learn how to operate your tractor. check to see that the brake is operating properly. See "TO CHECK BRAKE" in the Service and Adjustments section of this manual. A1 mismo tiempo que aprende a come usar su tractor, preste atencion extra a los puntos de importancia que se presentan a continuacion: V( El aceite deI motor tiene que ilegar at nive] adecuado. _" El estanque de combustible tiene que estarlleno con gasolina sin pfomo regular, nueva y Iimpia. _" Familiaricese con todos los controles - su ubicaci6n y su funci6n. Op6relos antes de hacer arrancar el motor. vf Aseg(Jrese 9ue el sistema de frenos est_ en una condicion de operaci6n segura. _' Asegurarse de que el Sistema de Presencia del Operador y el Sistema de Funcionamiento Atr_.s (ROS) funcionan de mode adecuado (Vet Ias Secciones de Funcionamiento y Mantenimiento en este manual). 8 These symbols mayappear onyourtractor orinliteraturesupplied with the product, Learn and understand their meaning. R N REVERSE H NEUTRAL i\! L HIGH LOW CHOKE FAST SLOW IGNITION ENGINE OFF U GHT,3 ON REVERSE OPERATION SYSTEM (ROe) FUEL ATTACHMENT CLUTCH DISENGAGED ENG|NE BATI'ERY ON ENGINE REVERSE ATTACHMENT CLUTCH ENGAGED START PARKING FORWARD DANGER, KEEP HANDS AND FEET AWAY BRAKE CRUISE MOWER HEIGHT CONTROL KEEP AREA CLEAR (SEE SAFETY SWITCH MOWERLIFT CLUTCWBRAKE PEDAL SLOPE RULES HAZARDS SECTION} DANGER if not avoided. will result indicates in death aorhazard seriouswhich, injury. FREE (Automatic WARNING hazard which, if not avoided, could resultindicates in deatha or serious injury. WHEEL Models only) CAUTION indicates a hazard which, if not avoided, might result in minor or moderate Injury. CAUTION when used without the alert symbol, indicates a situation that could result In damage to the tractor and/or engine. Failure to follow instructions could result in serious injury or death, The safety alert symbol is used to identify safety information about hazards which can result in death, serious injury and/or proper_ damage. HOT SURFACES indicates a hazard which, if not avoided, could result In death, serious Injury and/or property damage. FIRE indicates a hazard which, if not avoided. could result In death, serious injury and/or proPerty damage. 9 KNOW YOUR TRACTOR READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. 03078 Our tractors conform to the applicable safety standards of the American National Standards Institute, (A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your tractor. (F) IGNITION SWITCH - Used for starting and stopping the engine. (B) CLUTCH/BRAKE PEDAL -Used for declutching and braking the tractor and starting the engine, (G) REVERSE OPERATION SYSTEM (ROS) "ON" POSITION - Allows operation of mower or other powered attachment while in reverse. (C) PARKING BRAKE - Locks clutch/brake pedal into the brake position, (H) LIGHT SWITCH - Turns the headlights on and off, (D) THROTTLE/CHOKE CONTROL- Used for starting and controlling engine speed. (J) GEARSHIFT LEVER- Selects the speed and direction of tractor. (E) ATTACHMENT CLUTCH LEVER- Used to engagethe mower blades, or other attachments mounted to your tractor, 10 The operation of anytractor can result inforeign objects thrown into the eyes,t which can result in severe eye damage. Always wear safety glasses or eye{ shields while operating your tractor or performing any adjustments or repairs.I We recommend standard safety glasses or a wide vision safety, mask wornl over spectacles. / HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt bythe operator to leave the seat without first setting the parking brake will shut off the engine. 1. Depress clutch/brake pedal (B) all the way down and hold. 2. Pull parking brake lever (C) up and hold, release pressure from brake pedal (B), then release parking brake lever, Pedal should remain in brake position. Ensure parking brake will hold tractor secure. IMPORTANT: Leavingthe ignition switch in any position other than "STOP" will cause the battery to discharge and go dead. NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas. _CAUTION: Always stop tractor completely, as described above, and set parking brake before leavingthe operator's position. TO USE THROTTLE CONTROL (D) Always operate engine at full speed (fast). • Operating engine at less than full speed (fast) reduces engine's operating efficiency. • Full speed (fast) offers the best mower performance. STOPPING MOWER BLADES • To stop mower blades, move attachment clutch lever to disengaged position (t_). (1"_t) Attachment Clutch "ENGAGED (1_) .... TO MOVE FORWARD AND BACKWARD The direction and speed of movement is controlled bythe gearshift lever (J). Attachment Clutch DISENGAGED" GROUND DRIVE • Tostop ground drive, depress clutch!brake pedal all the way down, • Move gearshiftlever (J)to neutral position, ENGINE • Move throttle control (D) between half and full speed (fast) position. NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping, may cause engine to "backfire", • Turn ignition key (F) to "STOP" position and remove key. Always remove keywhen leaving tractorto prevent unauthorized use. 1. Start tractor with clutch/brake pedal depressed and gearshift lever in neutral position. 2, Move gearshift lever to desired position. 3. Slowly release clutch/brake pedal to start movement, IMPORTANT: Bring tractor to a complete stop before shifting or changing gears. Failure to do so will shorten the useful life of your transaxle. 11 TO ADJUST MOWER CUTTING HEIGHT The position of the attachment lift lever (A) determines the cutting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed, • The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance, grass over 6"in heightshouid bemowedtwice. Make the first cut relatively high; the second to desired height. TO ADJUST TO OPERATE MOWER Your tractor is equipped with an operator presence sensing switch, Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills. 1. Select desired height of cut with attachment lift lever. 2. Start mower blades by engaging attachment clutch control. TO STOP MOWER BLADES Disengage attachment clutch control. _kCAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place. TO OPERATE ON HILLS ,_kWARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. Use the slope guide provided at the back of this manual. ° Choose the slowest speed before starting up or down hills. • Avoid stopping or changingspeed on hills. • If stopping is absolutely necessary, push clutch/brake pedalquicklyto brake position and engage parking brake. • Move gearshift lever to 1st gear. Ensure you have allowed room for tractor to roll slightly as you restart movement. . Torestart movement, slowly release parking brake and clutch!brake pedal, • Make all turns slowly. GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE; Adjust gauge wheels with tractor on a flat level surface. 1, Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in this section of manual). 2. With mower in desired height of cut position, gaugewheels should beassembled so they are slightly offthe ground. Install gauge wheel in appropriate hole. Tighten securely. 3. Repeat for all, installing gauge wheel in same adjustment hole. TO TRANSPORT • Raise attachment lift lever to its highest. • When pushing or towing your tractor,ensure gearshift lever is in neutral position. • Do not push or tow tractor at more than five (5) MPH. 12 NOTE: To protect hood from damage when transporting yourtractor on atruckor atrailer, ensure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.). TOWING MENTS CARTS AND OTHER ATTACH- Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when tow=ng. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor. REVERSE OPERATION SYSTEM (ROS) Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position. _kWARNING: Backing up with the attachment clutch engaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary. USING THE SYSTEM - REVERSE ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to ensure fuel freshness. &CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. OPERATION Only use if you are certain no children or other bystanders will enter the mowing area. 1. Depress clutch/brake pedal all the way down and hold. IMPORTANT: When operating in temperatures below 32°F(00C), usefresh, clean winter grade gasoline to help ensure good cold weather starting. 2. With engine running, turn ignition key counterclockwise to ROS "ON" position. 3. Look down and behind before and while backing. 4. Movegearshiftleverto reverse (R) posi_ tion and slowly release clutch!brake pedal to start movement. 5. When useofthe ROS is nolonger needed, turn the ignition key clockwise to engine "ON" position. ROS "ON" PosJt_on BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine inyour tractor has been shipped, from the factory, already filled with summer weight oil. 1. Check engine oil with tractor on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for afew seconds, remove and read oil level. If necessary, add oil until "FULE' mark on dipstick is reached. Do not overfill. • For cold weather operation you should change oil for easier starting (See the oi_ viscosity chart in the Maintenance section of this manual). • Tochange engine o11, see the Maintenance section in this manual. CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. Engine "ON" Position (Normal Operating) ee 13 TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel. it will take extra cranking time to move fuel from the tank to the engine. 1. Sit on seat in operating position, depress clutch/brake pedal and set parking brake. 2. Place gear shift lever in neutral position. 3. Move attachment position. 4. Move throttle control to choke position. clutch to disengaged NOTE: Before starting, cold starting procedures read the warm and below. Insert key into Ignition and turn key clockwise to start position and release key as soon as engine starts. Do not run starter contin uo usly for mo re than fifteen seconds per minute. If the engine does not start after several a_empts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry. WARM WEATHER STARTING (50 ° F/10 ° C and above) When engine starts, move the throttle control to the fast position. • The attachments and ground now be used. If the engine does the load, restart the engine and warm up for one minute using as described above, COLD WEATHER drive can not accept allow it to the choke and more uniform cutting. f JJ • If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the desired height. STARTING When engine starts, reave throttle control in choke position until engine warms up and begins to run roughly. Once rough running begins, immediately move the throttle control to the fast position. Engine warm-up may take from several seconds to several minutes (the colder the temperature, the longer the warm-up). • D o not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing. • Always operate engine at full throttle when mowing to ensure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough speed to give the mower cutting performance as well as the quality of cut desired. • The attachments can also be used during the engine warm-up period, NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32°F/0°C) the carburetor fuel mixture may need to be adjusted for best engine performance (see "TO ADJUST CARB URETO R" in the Service and Adjustments clippings • When mowing large areas, start bytu rning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished. J (50 _ F/10 ° C and below) 7. • Mowershould be properly leveledforbest mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. , The left hand side of mower should be used for trimming, • Dnve sothat clippings are discharged onto the area that has already been cut, Have the cut areato the right of the tractor. This will result in a more even distribution of 5, 6. MOWING TIPS • Tire chains cannot be used when the mower housing is attached to tractor. • When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used. section of this manual). 14 MAINTENANCE SCHEDULE Check Brake 9EFORE _a_C:H USE I_VERY EV£RY B HOURS EVERY 2_ ohe.ok....... ,e.P Check Operatar Presence Check fe.rLoe.se Fasteners C T Ch_cWRe.p[ace Mower Lubr=cation Chz, rt Check R Clean Batten/andTermma_s Ore.an Debris Cheek Traes,,axle B_t;e.ry & NON Systems Cheek V-Be.Its Check ,," V' B[ade.e Level Off Steering Plate Ce.e.hng v' Enqlne i i| i m O=[ Level En_l_e E Clean Air Cle.an ALr ScTee.n Replr_ce E Cl_an En_me Co_ln Spark Armorer GENERAL Fur:l 9 Fins v" Plug Atr Filter Rep|a_ce Lv', Paper C_r_r_d_ie . V Fdter LUBRICATION RECOMMENDATIONS The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must ma=ntain tractor as instructed in this manual Some adjustments wilt need to be made pe riodically to properly maintain your tractor. At [east once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A EACH CHART (f_)Steering Pivot Botts Spindie__l_--_ (_Front! Wheet Bearing Zerk _Lc2_ _ %; \ I_ __;: X_ 4; _- ....._ Spindle _ Front Wheel Bearing /(_ (1) .Steering" Sector Gear I I Engine _erk Teeth new spark plug and clean air filter assure proper a=r-fuel mixture and help your engine run better and last longer. 5. v" is' Oil F=lter !If eClu_ppB_ ) Replace 1. 2. 3, 4. i|1 Filter Muter/SPark Re.p_aee. BEFORE H V',, Od (wFthout o_ filter) G If v',_ Chz_C.qe. Eni,}ine. O=| (WLth e.zl h_ter) Inspect BEFORE STORAGE V" Check Mowe.r Levelness | EVERY sEASO_ HOURS v', 0 U' 100 HQURS IOpe.ratten iA Chancle EVERY 50 _OURS _ Pivots OGeneral Purpose Grease @Refer to Maintenance"ENGINE" Section. USE Check engine oil level. Check brake operation. Check tire pressure. Check operator presence and ROS systems for proper operation. Check for loose fasteners. IMPORTANT: Do net oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self-lu bricating bearings. Ifyou feel they must be lubricated, use only a dry, powdered graphite type lubricant sparingly. 15 TRACTOR CHECK REVERSE OPERATION (ROS) SYSTEM Always observe safety rules whenperform-• Whenthe engine is running with the ignition switch in the engine "ON" position and the inganymaintenance. attachment clutch engaged, any attempt BRAKE OPERATION by the operator to drive in reverse should shut offthe engine. • When the engineis running withtheignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to drive in reverse should NOT shut off the engine. BLADE CARE If tractor requires more than five (5) feet to stop at highest speed in htghest gear on a level, dry concrete or paved surface, then brake must be serviced. (See "TO CHECK BRAKE" in the Service and Adjustments section of this manual). TIRES For best results mower blades must be sharp. Replace worn, bent or damaged blades. _kCAUTION: Use only a replacement blade approved bythe manufacturer ofyourtractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty. • Maintain proper air pressure in all tires (See PSI on tires). • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow Ieaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. BLADE I. 3. Install newblade with stamped "GRASS SIDE" facing the ground. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly, 4. Install and tighten blade bolt securely (45-55 Ft, Lbs.!62-75 Nm). IMPORTANT; Special blade bolt is heat treated, Star Center Hole CHECK OPERATOR PRESENCE SYSTEM ROS "ON" Position allow NOTE: Protect your hands with gloves and/ or wrap blade with heavy cloth, 2. Remove blade bolt by turning counterclockwise. OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) Ensure operator presence and reverse operation systems are workmg properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position. • When the engine is running, by the operator to leave the first setting the parking brake off the engine. • When the engine Is running tachment clutch is engaged, by the operator to leave the shut off the engine. • The attachmentclutch should ate unless the operator is in REMOVAL Raise mowerto highest positionto access to blades. any attempt seat without should shut \ and the atany attempt seat should Blade Bolt (Special) neveroperthe seat. Mandrel "_'" Assembly BA'f-I'ERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. Engine "ON" Position (Normal Operating) • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. 16 TOCLEAN BATTERY ANDTERMINALSDocking Corrosion and dirton thebatteryandterminals cancause thebattery to"leak" power. Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. 2. Rinse the battery with plain water and dry. 3. Clean terminals and battery cable ends with wire brush until bright. 4. Coat terminals w{th grease or petro{eum jelly. 5. Reinstall battery (See "REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). Oil Drain Extension 1. TRANSAXLE • Oil will drain more freely when warm. * Catch oil in a suitable container. 1. Remove oil ill] capldipstick, Be careful not to allow dirt to enter the engine when changing oil. 2. Stide oil drain extension from the docking position on the engine blower housing and extend outward from engine, 3, To open, twist cap counter-clockwise MAINTENANCE Keep transaxte free from build-up of dirt and chaff which can restrict cooling. Do not attempt to clean transaxle while engine is running or while the transaxle is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle. 4. After oil is drained completely, replace cap and twist clockwise until it stops. 5. Re-attach oil drain extension to engine blower housing. 6, Reffil enginewith oil through oil fill dipstick tube. Pour slowly, Do not overfill, For approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual. V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. 7. Use gauge on oil fill cap/dipstick for checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at "FULL_ line on dipstick. Tighten cap onto the tube securely when finished. ENGINE OIL FILTER ENGINE LUB RICATION Only use high quality detergent oil rated with AP[ service classification SG-SL. Selectthe oil's SAE viscosity grade according to your expected operating temperature. £AE V_SCOSR'Y Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. AIR FILTER GRADES Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See engine manual. NOTE: Although multi-viscosityoils (5W30, ] 0W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°F/0°C. Check your engine oil level more frequently to avoid possible engine damage from running low on oil CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damagefrom overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. Change the oil after every 50 hours of operation or at {east once a year if the tractor is not used for 50 hours in one year, ENGINE Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap[dipstick securely each time you check the oil level. TO CHANGE ENGINE COOLING SYSTEM Debris may clog the engine's air cooling system. Remove blower housing and clean the area shown to prevent overheating and engine damage. Air--Clean OIL Determine temperature range expected before oil change. All oil must meet API service classLfication SG-SL. • Be sure tractor is on level surface. /_ 17 Debris DECK WASHOUT PORT Your tractor's deck is equipped with a washout port o n its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your fawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor's discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2. Make surethe attachment clutch control is in the "DISENGAGED" position, set the parking brake, and stop the engine. 3. Thread the nozzle adapter (packaged with your tractor's Operator's Manual) onto the end of your garden hose. 4. Pull back the lock collar of the nozzle adapter and push the adapter onto the deck washout port at the left end of the mower deck. Release the lock collar to lock the adapter on the nozzle. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS" section of this manual. IN-LINE FUEL FILTER The fuel filter should be replaced once each season, If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. 1. With engine cool, remove filter and plug fuel line sections. 2. Place newfuel filter in position in fuel line with arrow pointing towards carburetor. 3. Ensure there are no fuel line leaks and clamps are properly positioned. 4. Immediatelywipe up any spilled gasohne. Hose_ Nozzlo/_ / _._._ "i / WashoutPort r_ 4-1 _1 amp IMPORTANT: Tug hose ensuring connection is secure. 5. Turn the water on. 6. While sitting in the operator's position on the tractor, re-start the engine and place thethrottle lever in the Fast",_" position. IMPORTANT: Recheck the area making certain the area is clear. 7, Move the tractor's attachment clutch control to the "ENGAGED" position. Remain in the operator's position with the cutting deck engaged until the deck is cleaned. 8. Move the tractor's attachment clutch control to the "DISENGAGED" position. Turn the ignition key to the STOP position to turn the tractor's engine off. Turn the water off. 9. Pull back the lock collar of the nozzle adapter to disconnect the adapter from the nozzle washout port. 10. Move the tractor to a dry area, preferably a concrete or paved area. Place the attachment clutch control _n the "ENGAGED" position to remove excess water and to help dry before putting the _ll tractor away. WARNING: A broken or missing washout fitting could expose you or others to thrown objects from contact with the blade. • Replace broken or missing washout fitting immediately, prior to using mower again. * Plug any holes in mower with bolts and Iockn uts. CLEANING • • Clean engine, battery, seat, finish, etc, of all foreign matter. Clean debrisfromsteering plate. Debris can restrictclutch!brake pedal shaft movement, causing belt slip and loss of drive. /i, CAUTION: Avoid movable parts _- _. 4/ all pinch points and Clutch/brake pedal ." f,' Clean _o_+ I/ top side _ ._//-." /i"" Steerlngplate_,.-;" "_ ¢ .... Steering System, Dash, Fender and Mower Not Shown CAUTION: I Pinch I 41_ Points I • Keep finished surfaces and wheels free of all gasohne, oil, etc. • P rotect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower. 18 SERVICE ORTO WARNING: ADJUSTMENTS: AVOID SERIOUS INJURY, BEFORE PERFORMING ANY 1. Depress clutch/brake pedal fully and set parking brake. 2. Place gearshift lever in neutral position, 3. Place attachment clutch in "DISENGAGED" position. 4. Turnignitionkey to "STOP" and remove key. 5. Ensure the blades and all moving parts have completely stopped, 6. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER 1, Place attachment clutch in "DISENGAGED" position. 2, Lower attachment lift lever to its lowest position. 3. Roll belt off engine pulley (M) and belt keepers ((3). 4. Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket. 5. Remove clutch cable spring (Q) from idler arm (R). 6. Disconnect front link (E) from mower remove retainer spring and washer. 7. Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers, A_kCAUTION: 8. Slide mower outfrom underrights!de of tractor. IMPORTANT: If an attachment other than the mower is to be mounted on the tractor, remove the front link (E) and rear lift links (C) from tractor and hook the clutch spring (Q) into the cable guide on front edge of lower dash. TO INSTALL MOWER Ensure tractor is on level surface and engage parking brake. I. Lower attachment lift lever to its lowest position. CAUTION: Lift lever is spring loaded. Have a tight grip on lift lever, lower it slowly and engage in lowest position. NOTE: Ensure mower side suspension arms (A) are pointing forward before sliding mower under tractor, 2. Slide mower under tractor until it is centered under tractor. After rear lift links are discon- nected, the attachment li_ leverwill be spring loaded. Have a tight grip on lift lever when changing position of the lever, 03042te× 19 3. 4. ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. Repeat on opposite side of tractor. 7. Insert end of link (E) into hole in front mower bracket (H) and secure with washer and retainer spnng (J). 8. into 5. ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin (D) on rear mower bracket and secure with washer and retainer spring. Hook end of clutch cable spring (Q) hole in idler arm (R). 9. Push clutch cable houstng guide (P) bracket, slide collar (L) onto guide secure with retainer spnng (K). t0. install belt onto engine pulley (M) and keepers (G). 6. ATTACH FRONT LINK (E) - Work from left side of tractor. Insert rod end of link assembly through front hole in tractor front suspension bracket (F). IMPORTANT: Check belt for proper tn all mower pulley grooves. 11. Raise attachment lift lever to position. 12. If necessary, adjus_ gauge wheels operating mower as shown in the tion section of this manual. into and belt routing htghest before Opera- 03042[ex 2O FRONT-TO-BACK ADJUSTMENT TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown ontires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly. VISUAL SIDE-TO-SIDE ADJUSTMENT IMPORTANT: to-side. must be level side- To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the ,_ower is in its highest position. CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap btade with heavy cloth. • Raise mower to highest position. • Position any blade so the tip is pointing straight forward, Measure distance (13) to the ground at front and rear tip of the blade. • If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor. • With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B. 1. With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower. 2. With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower. NOTE: Each full turn of adjustment nut wilt change mower height about 3/16". Turn nut ri to raise mower Deck • With a 3/4" or adjustable wrench, turn front link adjustment nut (B) clockwise (tighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower. Turn nut left to lower mower 3. Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results. PRECISION SIDE-TO-SIDE ADJ USTMENT 1. With all tires properly inflated, park tractor on level ground or driveway. CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. 2. Raise mower to its highest position. 3. At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides. 4. If adjustment is necessary, see step 2 in V_sual Adjustment instructions above. 5. Recheck measurements, adjust if necessary until both sides are equal. Tighten adjust nut B to raise mower Loosen adjust nut B to lower mowel" Loosen jam nut A first NOTE: Each full turn of the adjustment nut willchange mower height about 1/8% • Recheck measurements, adjust if necessary until front tip of blade is 1/8" to t/2" bowerthan the rear tip. • Hold adjustment nutin position with wrench and tighten jam nut securely against adjustment nut. At 21 TO REPLACE BELT MOWER BLADE TO REPLACE DRIVE The mower blade drive belt may be replaced without tools, Park the tractor on level surface. Engage parking BELT REMOVAL brake. - BELT REMOVAL 1. Remove mower from tractor (See "TO REMOVE MOWER" in this section of 2. 3. manuat). Work belt off both mandrel idler pulleys. Pull belt away from mower. BELT t NSTALLATIO pulleys MOTION DRIVE BELT Park the tractor on level su#ace. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest, - 1. Remove mower (See "TO REMOVE MOWER" in this section of manual). NOTE: Observe entire motion drive belt and and position of all belt guides and keepers. 2. Remove beltfrom stationary idler (A) and clutching idler (B). 3. Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (D). 4. Remove belt downward from engine pulley (E). 5. Slide belt toward rear of tractor, off the steering plate (F) and remove from tractor. N - 1. Work belt around both mandrel pulleys and idler pulleys 2. Ensure belt is in all pulley grooves and inside all belt guides. 3. Install mower (See "To Instal] Mower" in this section of this manual). Idler Pulleys Mandrel ,Pulley TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. BELT INSTALLATION You may also check brake by: 1. Park tractor on a Jevel, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake, 2, Place gear shift lever in neutral position. The rear wheels must lock and skid when Install new belt from tractor rear to front, over the steering plate (F) and above clutch brake pedal shaft (G). 2, Pull belt toward front of tractor and roll belt onto engine pulley (E). Pull belt toward rear of tractor. Carefully work bell down around transaxle input pulley (D). Ensure belt is inside the belt keeper. 4. Install belt through stationary idler {A) and clutching idler (B). 5. Ensure belt is in all pulley grooves and inside all belt guides and keepers. 6. Install mower (See "TO INSTALL MOWER" in this section of manual). 3. you try to man ualiy pus h the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a Sears or other qualified service - 1. center. 22 TRANSAXLE GEAR SHIFT TRAL ADJUSTMENT LEVER NEU- FRONT WHEEL TOE-IN/CAMBER Your new tractor front wheel toe-in and camber is set at the factory and is normal, The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a Sears or other qualified service center. The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: 1. Ensure transaxle is in neutral (N). NOTE: When the tractor rear wheels move freely, the transaxle is in neutral. 2. Loosen adjustment bolt in front of the right rear wheeL. 3. Position the gear shift lever in the neutral (N) position. 4. Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bo]t, move mower deck height to the lowest position. Gearshift Lever Adjustment Bolt TO REMOVE WHEEL TO START "FIERY WITH A WEAK BAT- _WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manual). If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles. TO ATTACH JUMPER CABLES 1. Connectoneend ofthe RED cabletothe POSITIVE (+) terminal of each battery(AB), taking care notto short againsttractor chassis. 2. Connect one end of the BLACK cable Neutral Lock Gate FOR REPAIRS to the NEGATIVE (-) terminal (C) of fully charged battery. 3. Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery. 1. Block up axle securely. 2. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do net lose). 3. Repair tire and reassemble. NOTE: On rearwheels only: align grooves in rearwheel hub and axle. Insert square key. 4. Replace washers and snap retaining ring securely in axle groove. 5. Replace axle cover. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion. TO REMOVECABLES, REVERSEORDER1. BLACK cabIe first from chassis and then from the fully charged battery. 2. RED cable last from both batteries, Retaining Weak or Dead Battery # Axle Cover ENGINE "_8qu;_re Key (Rear Wheel On]y) 23 Fully Charged Battery REPLACING TO REPLACE FUSE Replace with 30 amp automotive-type plugin fuse, The fuse holder is located behind the dash. BA'I-I'ERY n_asWARNING: Do not short battery termiby altowi nga wrench o r any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental g rounding. TO REMOVE HOOD AND GRILL ASSEMBLY 1. Raise hood. 2. 3. 1. Lift seat pan to raised position. 2. Remove terminal cover, 3, 4. 5. Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor, Install new battery with termtnals position as old battery. Reinstall terminal cover. _nsame 6. First connect RED battery cable to positive (+) battery terminal wtth bolt and nut as shown, Tighten securely. 7. Connect BLACK grounding cable to negative (-) batteryterminal with remaining bolt and nut. Tighten securely Lower seat pan. 8. Headlight Wire Connector ENGINE TO ADJUST THROTI-LE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be necessary Check adjustment as described below before loosening cable. Ifadjustment is necessary, see engine manual. Nut Terminal Ceverx 4. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. When replacing hood, ensure to reconnect the headlight wire connector. Bolt (Black) Negative Positive (Red) TO ADJUST TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Remove bulb holder from the hole in the backstde of the grill. 3. Replace bulb m holder and install bulb holder securely back into the hole in the backside of the grill. 4. Close hood. INTERLOCKS CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual. TO ADJUST CARBURETOR You r carburetor has been preset at the factory and adjustment should not be necessary. However, m=nor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the enginedoes need adjustment, see engine manual. AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. 24 immediately prepare your tractor forstorageENGINE attheendoftheseason orifthetractor will FUEL SYSTEM notbeusedfor30daysor more. IMPORTANT: It A_, WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure, TRACTO R Remove mower from tractor for winter storage. When moweristo bestored foraperiod of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in aclean, dry area. 1, Clean entire tractor (See"CLEANING" in the Maintenance section of this manuaf). 2. Inspect and replace belts, ff necessary (See belt replacement instructions in the Service and Adjustments section of this manual). 3. Lubncate as shown in the Maintenance section of this manual. 4, Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. 5. Touch up all rusted or chipped paint surfaces; sand lightly before painting. BATTERY • Fully charge the battery for storage. • After a period of time in storage, battery may require recharging. • To help prevent corrosion and power leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see "TO CLEAN BATTERY AND TERMINALS" m the Maintenance section of this manual). • Aftercleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals. • If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces. is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. • Em pry the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty. • Never use engine or carburetor cleaner products in the fuet tank or permanent damage may occur. • Use fresh fuel next season. NOTE: Fuei stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes afteradding stabilizer to al[owthestabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer, ENGINE OIL Drain oil (with engine warm) and replace with clean engine oil (See "ENGINE" inthe Maintenance section of this manual). CYLINDER(S) 1. Remove spark plug(s). 2. Pour one ounce of oil through spark plug hole(s) into cylinder(s). 3. Turn ignition key to "START" position for a few seconds to distribute oil. 4, Replace with new spark plug(s). OTHER • Do not store gasoline from one season to another. • Reptace your gasoline can ifyourcan starts to rust. Rust and/or dirt in your gasoline will cause problems. • tf possible, store your tractor indoors and cover itto give protection from dust and dirt. • Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust. IMPORTANT: Never cover tractor while engine and exhaust areas are still warm. 25 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start CORRECTION CAUSE 1 Out of fuel. 1 F=llfuel tank. 2 Engine not "CHOKED" properly. 2 See '_TO START ENGINF Operation section. Wait several minutes before attemptmg to start. Engine flooded. 4 Bad spark plug. 4 Replace spark plug. 5 Dirty air fitter. 5 Clean!replace 6 Dirty fuel filter. 6 Replace {uel filter. 7 Water in fuel. 7 Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8 Loose or damaged wiring. 8 Check all wiring. 9 Carburetor 9 See "To Adjust Carburetor" in Service end Adjustments section. 1D Contact a Sears or other qualified service center. 10 Hard to start Engine will not turn over in out of adjustment_ Engine valves out of adjustment. air filter. 1 Dtrty at r filter. 1 Clean]replace 2 Bad spark plug. 2 Replace spark pEug. 3 Weak or dead battery. 3 Recharge or replace battery. 4 Dirty fuel filter. 4 Replace fuel filter. ,5 Stale or dirty fuel. i5 Empty fuel tank and refill tank wttL fresh, clean gasoline. 6 Loose or damaged wiring_ i6 Check all winng. 7 Carburetor out of adjustment. air filter. 7 See "To Adiust Carburetor" in Service and Adjustments sectton. Engine valves out of adjustment_ 8 Contact a Sears or other qualified service center. 1 Clutch/brake I Depress clutch/brake 2 Attachment 2 Disengage 3 Weak or dead battery. 3 Recharge or replace battery. 4 Blown fuse 4 ! Replace fuse. 5 Corroded battery terminals. 5; i Clean battery terminals. 6 Loose or damaged wiring. 6 7 Faulty ignition switch. 7 i Check/replace 8 Faulty solenotd or starter. 8 Check/replace !9 Faulty operator presence switch(es). 9 Contact a Sears or other qualified service center. pedal not depressed. clutch is engaged. 26 pedal attachment clutch. Check all wtfing. ignition switch. solenoid or starter. TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE Engine clicks but will not start Loss of power iExcessive vibration CORRECTION 1 Weak or dead battery. 1 Recharge or replace battery. 2 Corroded battery terminals. 2 Clean battery terminals. 3 Loose or damaged wiring. 3 Check all wiring, 4 Faulty solenoid 4 Check/repEace solenoid orstarter. 1 Cutting too much grass]too fast. 1 Raise cutting height]reduce speed. 2 Throttle position. 2 Adjust throttle control. 3 Build-up of grass, leaves and trash under mower. 3 Clean underside housing. 4 Dirty air filter. 4 ClearV'replace air filter. 5 Low oil revel/dirty oil. 5 Check oil level!change 6 Faulty spark plug. 6 Clean and regap or change spark p{ug. 7 D_rty fuel filter. 7 Replace fuel filter. 8 Stale or d_rty fuel. 8 Empty fuel tank and refill tank witl" fresh, clean gasotine. 9 Water infue[ 9 Empty fuel tank and carburetor, refill tank with fresh gasol{ne and replace fuel filter. 10 Spark plug wire loose. 10 Connect and tighten spark plug wire. 11 Dirty engine air screen/fins. 11 Clean engine air screen!fins. 12 Dirty/clogged 12 Clean/replace 13 Loose or damaged wiring. 13 Check all wiring. 14 Carburetor 14 See _To Adjust Carburetor" in Service and Adjustments section. 15 Engine valves out of adjustment. 15 Contact a Sears or other qualified service center. or starter. in "CHOKE" muffler. out of adjustment. of mower oil. muffler. 1 Worn, bent or loose blade. I Replace blade. Tighten blade bolt. 2 Bent blade mandrel. 2 Contact a Sears or other qualified service center. Loose]damaged Engine continues to 1 run when operator leaves seat with attachment clutch engaged part(s). Faulty operator-safety control system. 27 presence 3 Tighten loose part(s). Replace damaged parts. 1 Check widng, switches and connections. If not corrected, contact a Sears or other TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Poor cut CAUSE - uneven cutting 1 Worn, bent or loose b_ade. 1 Replace blade. Tighten blade boJ 2 Mower deck not level. 2 Level mower deck. 3 Clean underside of mower housing. 3 Mower blades i not rotate will Poor grass discharge Bent blade mandrel. 4 Contact a Sears or other qualified service center. 5 Clogged mower deck vent from build-up of grass, leaves, and trash around mandrels 5 Clean around mandrels open vent hates. 1 Obstruction 1 Remove obstruction. 2 Worn/damaged 2. Replace mower drive belt. 3 Frozen Idler pulley. 3 Replace idler pulley. 4 Frozen blade mandrel. 4 Contact a Sears or other qualified service center. 1 Engine speed too sEow. 1 Place throttle control in "FAST" )oslhon 2 Travel speed too fast. 2 Shift to slower speed. 3 Wet grass. 3 Allow grass to dry before mowing, 4 Mower deck not level, 4 Level mower deck. 5 Low/uneven 5 Check tires for proper PSI. 6 Worn, bent or loose blade. 6 Replace/sharpen blade bolt. 7 Buildup of grass, leaves and trash under mower 7 Clean underside of mower housing. 8 Mower drive belt worn. 8 ! Replace mower drive belt. 9 Battery charge will not Butldup of grass, leaves, and i trash under mower, 4 :I0 Headlight(s) not working (if so equipped) CORRECTION in clutch mechamsm. mower drive belt. t=reair pressure. Blades improperly installed. Improper blades used. 9 10 to blade. Tighten Reinstall blades sharp edge down, Replace with blades listed in this manual. 11 Clogged mower deck vent holes I1 from buildup of grass, leaves, and trash around mandrels. Clean around mandrels open vent holes. 1 L=ghtswitch is "OFF". 1 Turn light switch "ON". ;z Bulb(s) or lamp(s) burned out. 2 Replace bulb(s) or lamp(s). 3 Faulty light switch. 3 Check/replace 4 Loose or damaged winng. 4 Check wiring and connections. S Blown fuse. 5 Replace fuse. light switch 1 Bad battery cell(s), 1 Replace battery 2 Poor cable connections. 2 Check!clean 3 Faulty regulator 3 Replace regulator_ 4 Faulty alternator. 4 Replace alternator. (_fso equipped). 28 to allconnecttons. TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Loss of drive CAUSE i I Debris on steedng equipped), CORRECTION plate [if 1 See "CLEANING" in the maintenance section, Replace motion drive belt. 2 Motion drive belt worn, damaged, or broken. 2 3 Axle key missing. 3 Engine"backfires" when turning engine "OFF" I Engine throttle control not set between half and full speed/fast) position before stopping engine, 1 Move throttle control between half and full speed (fast) position before stopping engine. Engine dies when tractor is shifted into reverse 1 Reverse operation system (ROS) is not "ON" while mower or other attachment is engaged. 1 Turn ignition key to ROS "ON" position. See Operation section. Instal] axle key at rear wheel. See "TO REMOVE WHEEL" in the Service and Adjustments section. NEED MORE HELP? YouQ[ find the answer and more on managemyhome.com • Find this and air your other product manuals online. • Get answers from our team of home experts. • Get a personalized maintenance pLanfor your home. • Find information and tools to help with home projects. manage home brought to you by Seaz_ 29 - for free! SUGGESTED ,..... GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ...,= ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL CO c_ 15 DEGREES _b MAX. down the face of slopes, never across the face. Do not mow ARNING: To avoid serious injury, operate your tractor up and slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2. HoEd page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. Garant{a .......................................................... Reglas de Seguridad ...................................... Especificaciones det Producto ........................ Montaje/Pre Operaci6n ................................... Operaci6n ....................................................... Mantenimiento ................................................ 31 32 35 36 38 44 Programa de Mantenimiento .......................... 44 Servicio y Ajustes ........................................... 48 Almacenamiento ............................................. 54 Identificaci6n de Problemas ........................... 55 Servicio Sears ............................. Contraportada Garantia para equipos tractores Craftsman GARANTiA COMPLETA DE CRAFTSMAN POR DOS ANOS desde la fecha de compra, todas los partes no sustituibles de este equipo tractor est_n garantizadas contra cualquier defecto de material o mano de obra. Una parts no sustituible defectuoSa recibir& reparaci6n o reemplazo gratuito en case sila reparaci6n es imposible. POR OINCO AltOS desde la fecha de compra, el bastidor y el eje delantero de este equipo tractor est_,n garantizados contra cualquier defecto de material o mano de obra. Un bastidor o eje delantero defectuoso recibir& reparaci6n o reemplazo gratuito en case sila reparaci6n es imposible, DURANTE 90 DiAS desdg la fecha de compra, la bater{a (una parts sustituible) de este equipo tractor est,= garantizada contra cualquier defecto de material o mano de obra (nuestra prueba compruaba que no contendr& cargo). Una bater_a defectuosa recibirz_ un reemplazo gratuito en case. GARANTiA LIMITADA DE POR VIDA ADICIONAL en el EJE DELANTERO DE HIERRO COLADO (el est_ provisto) DURANTE EL TIEMPO EN QUE SE USE pot ef propietario original despu_s de[ quinto aSo a partir de la fecha de compra, el eje delantero de hierro colado (siest& provisto) de este equipo tractos est,'_ garantizado contra cualquier defecto de material o mano de obra. Con el comprobante de compra, un eje delantero de hisrro colado recibir& un reemplazo gratuRo en c_sa. SERVICIO DE GARANTiA Pare conocer k)s detalles de la cobertura de garantla para obtener una reparaci6n llama aI t-800-659-5917 6 visits e] sitio web: www. craftsman.com En todos los casos anteriores, si el reemplazo el mismo modelo o uno equiva[ente. o reemplazo es imposible, el equipo tractor ser__ sustituido Toda la cobertura de garantia anterior set& nula sieste servicios comerciales o sise alquila aotra persona. gratuito, sin cargo con equipo tractor se utilize alguna vez pare brindar Esta garantia cubre UNICAMENTE defectos de material y mano de obra. La cobertura de garantfa NO inciuye: • Partes sustituibles (excepto la bateria) qua se puedan desgastar pore] uso normal dentro del per{odo de garantia incluso, pero sin limitarse a, cuchi[]as, bujias, filtros de airs, correas y filtros de aceite, • Servicios de mantenimiento est_ndar, cambios de aceite o afinaciones. • Reemplazo o reparaci6n de neum&ticos pot pinchezos causados por objetos extemos como clavos, espinas, tocones o viddos. , Reemp[azo o reparaci6n de neum&ticos o ruedas por desgaste normal, accidentes o por operaci6n o mantenimiento incorrectos. • Reparaciones necesarias por abuso del operador inc[uso, pero sin limitarse a, daSos causados pot remolcar objetos qua superen la capacidad del equipo tractor, chocar contra objetos qua doblen el bastidor, el ensamb{e del eje o el cigt3eSal o sobrepasar la velocidad del motor. • Reparaciones necesarias por negligencia del operador, incluso (pero sin [imitarse a silo) daSos eI6ctdcos y mec&nicos causados pot el almacenamiento incorrecto, por no usar el grado y la cantidad correctos de aceite de motor, por no mantener deI mueI[e libra de residuos inflamab]es o por no mantener el equipo tractor de acuerdo con los instruccionss qua contiene el manual de]-operador. • Limpieza o reparaciones del motor (sistema de combustible) cuando se determine qua se us6 combustible contaminado y oxidado (sarro). En general, el combustible debe usarse dentro de los 30 d{as posteriores a su campra. • Deterioro y desgaste normal de los acabados extedores o sustituci6n de r6tulos de productos. Esta garant{a Ie otorga derechos legales especfficos, y usted tambi_n puede tenet otroe derechos que varian de un estado a otro. Sears BrandsManagementCorporation, HoffmanEstates,IL 60179 31 _PELIGRO: Esta Maquina cortadora es capaz de amputar las manosy los pies y de lanzar objetos, si no se observan los instrueciones de seguridad siguientes se pueden producir lesiones graves o la muerte. • No maneje la m#,quina si no tiene la trampa _DVERTENCIA: S=empre desconecte el alampara c.,_sped completa, la canaleta de descarga bre de la bujia y p6ngalo donde no pueda entrar u atlas dispositivos de seguridad en se lugar en contacto con la bujia, para ewtar el arranque yen funcionamiento. per accidente, durante la preparaciSn, el transporte, el aiuste o cuando se hacen reparac_ones. _DVERTENClA: No avarice cuestaabajo a punto muerto ya que podria perder el control def tractor. _,DVERTENCIA" Remolque solamente los accesorios recomendados y conformes a ras caracterist=cas ind=cadas par el fabricante de su tractor. Tonga cuidado y prudencia al utihzar e[ tractor Cuando se encuentre en un declive, oper utt hzando excluslvamente la veloctdad m_s baja_ En case de un dechve una carga excesiva podrfa resultar pehgrosa Los neum_tieos pueden pettier la tracct6n con el sueto y hacerle perder el control de su tractor _ADVERTENClA: El tuba de escape del motor, algunos de sus const=tuyentes y algunos componentes del vehiculo contienen o desprenden productos qulmtcos conocidos en el Estado de Calfforn=a coma causa de c_ncer y defectas al nac_mlento u otros dafios reproductivos GENERAL Limpiar el __rea de objetos coma piedras, juguetes, cables, etc. que pueden set recog_dos y disparados con Ias cuchiHas. • Asegurarse de que el &rea est_ Iibre de otras personas antes de panerla en marcha. Parar la m&quina si alguien entra en el _trea. Nunca Ilevar pasaleros. No cortar marcha atr&s al no ser absolu- • • tamente necesario. Mirar siempre delante mientras se precede atr&s. • abajo • Hacer funclonar la m_.quina s61o con la l uz del dia o luz artificial buena. • No hacer funcionar ia m_quina estando bajo los efectos de alcohol o droga • Porter atencl6n al tr_f[co cuando se opera cerca de calles o se cruzan. Poner la m_xima atenciSn al cargar o descargar la maquina en una caravana o camton. • Llevar siempre gafasde proteccion cuando se hace funcionar la m&quina. • Los dates tndtcan que los operadores a partir de los 60 a_es est_.n afectados par un gran porcentale de heridas relatlvas a Ia conducci6n del cortac6sped. Estos operadores tendrian que evaluar su hab=lidad de hacer funcionar el cortac6sped de mode Io bastante seguro para proteger a si m=smos y a otras personas de heridas graves. • Seguir los recomendactones de[ fabricante para los pesos y contrapesos de los ruedas. • Leer, entender y segu_r todas los instrucciones sabre la m&quina yen el manual antes de empezar. • No porter las manes o los p=es cerca de partes giratorias o debajo de la m_quina, mantener siempre hmpta la abertura de descarga. • Permitir el funclonamiento de la m&quina s61o a adultos que tengan familiaridad con las instrucciones. • Ralentizar antes de girar. Nunca dejar una maquma encendida sin vigilancia. Apagar siempre [as cuchillas, porter el freno de estactonamiento, parar el motor, y quitar las tlaves antes de bajar. • Desenganche los halos cuando no est6 cortando cesped. Apague el motor y espere hasta que todas [as partes se detengan par complete antes de limpiar la m,iquina, retlrar la trampa para c6sped o destapar [a cana[eta de descarga. • _ADVERTENCIA: Los barnes, terminales y accesonos relatives de la bateria contienen plomo o compuestos de plomo, productos quimicos conocidos en el Estado de Calffornta come causa de c_.ncer y defectos al nac=m=ento u arras da_os reproducttvos Lavar los manes despu6s de manipularlos. I. FUNCIONAMIENTO • • • Mantener la m#,quina hbre de hierba, hojas u otros escombros que pueden tocar el tuba de escape/partes del motor catientes y quemarse. No permltir que el puente del cortac_sped cargue hojas u otros residues que pueden causar acumulaciones Limpiar toda salpicadura de aceite o carburante antes de hacer operactones sabre la m_.quina o guardarla. Dejarla enfriar antes de guardarla. I!. FUNCIONAMIENTO EN PENDIENTES Los pendientes sen el mayor factor de accJdentes relattvos a la p6rdida de control y vuelco, que pueden causar severas heridas o muerte. El funcionamiento en pendientes requiere una atenoi6n extra. Si no es posibie hacer marcha atrAs en una penal=onto o si te sientes incomodo, no la cortes. • Cortar hacia arriba y abajo de una pendiente, no de mode horizontal. y Nunca d{rigir el material descargado hacia nadie. Evitar descargar material contra paredes u obstrucc_ones. El material podria rebotar hacia el operador. Parar los cuchlllas cuando se pasan superficies de gravar 32 • Porter atenciones a los hayes, los raices, los bultos, los piedras u otros objetos escondidos. El terreno =rregular puede volcar la mAquina. La hierba alta puede esconder obsta.culos. • Tener el m_ximo cuidado cuando se acerca a cantos ciegos, arbustos, _.rboles u otros objetos que pueden impedir la vista de niOos, ° Escoger una velocidad de marcha baja de mode que no sea necesario pararse o eambiar estando en una pendiente. • No cortar la hierba mojada. Las ruedas pueden perder tracciOn. Poner s_empre una marcha cuando se est'. en pendientes. No poner en punto muerto e _r cuesta abalo • Evitar arrancar, pararse o girar en una pendlente. Si las ruedas pierden tracc_On, desconectar las cuchillas y preceder despacio cuesta abajo en la pendiente. • Mantener todo los movimientos en [as pendientes lentos y gradual. No hacer cambios repentinos de velocidad o direcc_0n, ya que pueden causar e[ escape de la rn&qu_na. • Poner la rn&xima atenci6n cuando la m&quina funciona con captaderes de hierba u otros dispositivos enganchados; pueden afectar ]a estabdidad de la m&quina. No usar en pendientes empinados. IV. REMOLQUE • Rernolcar s61ocon una m&quina que tenga un gancho diseOado pare remolcaro Enganchar el equipo o remolcar s61o en el punto dispuesto al efecto. • Segu_rlas recomendaciones del productor con respecto a los lirnites de[ equipo per remo[ear y el rernolque en pendientes. • Nunca permitir que niOos u otres personas estOn dentro del equipo per remolcar. • En pendientes, el peso del equipo remolcado puede causer la pOrdida de tracciOn y la pOrdida de control. • Viajar despacio y dejar rnAs distancia para frenar. V. SERVICIO MANIPULACION SEGURA DE LA GASOLINA • No intentar estab_lizar la rn&quina poniendo el pie en el terreno. • No cortar cerca de bajadas, cunetas y orillas. Las m_tquina puede volcarse improvisamente si una rueda est& en el horde o se hunde. Para evitar heridas personales o defies alas cosas, porter el m&ximo euidado ala hera de rnanipular la gasoline. La gasoline es extremamente inflarnable y los vaperes son explosives. • Apagar todos los cigarril}os, cigarros, pipas y otras fuentes de igniciOn. • Usar sOlocontenedores pare gasotina aprobados. IlL NllTIOS _,ADVERTENGIA: LOS NII_OS PUEDEN SUFRIR DANES CON EL use DE ESTE EQU[PO. La Academia Estadeunidense de Pedlatria • Nunca quitar el tap6n de la gasoline o a5adir carburante con el motor en marcha, dejar enfriar el motor antes del abastecimiento de la gasoline. • Nunca abastecer la m_.quina al interior de un local. ° Nunca guarder la m&quina o el c_ntenedor del carburante donde haya una llama abierta, chispas o una luz piloto come un caientador de ague u otros dispositivos. • Nunca Ilenar los centenedores al interior de un vehiculo o en una caravana o cami6n recubiertos con un form de pl&stieo. Colocar siempre los contenedores en el terreno lejos del vehlculo cuando se est& llenando. (American Academy of Pediatrics) recomienda que sOlo se permita a niOos con una edad minima de I2 ar_os manejar m&quinas cortac#sped manuales, y al menos de 16 aOos para rnanejar tractores cortac_sped. Si el operador no pone atencidn ala presencia de los niOos pueden ocurdr accidentes tr&gicos. Los nlr_os a rnenudo est#.n atraidos per fa rn&quina y las actividad de cortar. No dar per hecho de que los nifios se queden adonde estaban la _ltima vez que los vistes. • Mantener los niOos fuera del #.rea de corte y wgdados per un adulto responsable que no sea el operador • Estar aler[a y apagar la m#.quina si un niOos entra en el &rea. • Quoterel equ_pode gas del carnion o caravana y abasteeedo en e[ terreno. Si no es posible, abastecer dicho equipo con un contenedor portAtil, m&s bien que de un surtidor de gasolina. • Mantener la boquilla a contacto def borde de[ depOsito de carburante o la abertura del contenedor durante toda la operaciOn de abastecirniento. No utilizer un dispositivo con boquilta cerrada-abierta. • Si se vierte carburante sobre la rope, cambiarse la ropa inmediatamente. ° Nunca flenar e[ depOsito m#.s de Io debido. Velvet a colocar el tapOn del gas y cerrar de mode firme. • Antes y durante la rnarcha atr&s, miter adelante y abajo para vet si hay nifios pequeOos. • Nunca flevar nlOos, incluso si hay las cuchil}as apagadas. Poddan caer y herirse seriamente o interferir con el funcionamiento seguro de la m&quina los niOos que se han [levado precedentemente pueden aparecer de pronto en el &tea de corte per otro paseo y ser atropellados o tumbados per la m_quina. • Nunca dejar que los nifios rnanipulen la m_.quina. 33 OPERACIONES DE SERVIC]O GENERALES • Nunca hacer funcionar EamAquina en un __rea cerrada. • Mantener todas Jastuercas y pernos apretados para asegurarse de que trabaja en condic=ones seguras. • Nunca modificar los d=spositivos de seguddad. Cont[olar su correcto funcJonamiento regularmente. • Mantener [a mAquina libra de hierba, hojas u otros residuos acumulados, Limplar las salpicaduras de acelte o carburante y quitar cualqu_er cosa mojada con carburante. Dejar qua Jam_quina se enfrie antes de guardarla. • Controlar el func_onam_ento def #eno frecuent- emente, Ajustar y hacer las operaciones mantenimiento cuando eso sea necesario. • Ver[flque los componentes de la trampa para c@sped y ]a canaleta de descarga con frecuenciay sustituya con repuestos recomendados por el fabricante cuando sea necesario. • Las cuchillas del cortac_sped son afliadas. Envolver la cuchilla, ponerse guantes y porter la maxima atenci6n cuando se hacen operaclones en elias, • de • Mantener y sustituir las etiq uetas de seguridad e instrucci6n, cuando sea necesano. • Asegurarse de que el Area est_ libre de otras personas antes de ponerla en march& para la mAquina si algu_en entra en el Area. • • Nunca Ilevar pasajeros. No cortar marcha atrAs al no set absolutamente necesarJo. Mirar siempre abajo y delante mientras se procede atrAs. • Nunca Ilevar nlSos, incluso si hay las cuchitlas apagadas. Podrian caer y herirse seriamente o interfenr con el func_onam_ento seguro de la mAquina, los nir_os qua se hart Ilevaclo precedentemente pueden aparecer de pronto en el _rea de corte per otro paseo y ser atropellados o tumbados pot fa mAquina. • • Si se golpea un objeto ajeno, hay qua pararse e inspecc_onar la mAquina. Reparar, si es necesario, antes de volver a porter en marcha. • Nunca hacer ningL1n ajuste o reparaci6n con el motor en funci6n. Estar alerta y apagar entra en el _rea. la mAqu[na si un niSos • Antes y durante la marcha atrAs, mirar adelante y abaje para ver si hay nines pequehos • Cortar hacia arriba y abajo de una pendiente (I5 ° MAx), no de mode horizontal. • • • • Mantener los niSos fuera del Area de corte y vigilados pot un adulto responsable que no sea el operador. • 34 Escoger una velocidad de marcha baja de modo que no sea necesario pararse o cambiar estando en una pendiente. Evitar arrancar, pararse o girar en una pendiente. S_ las ruedas pierden tracci6n, desconectar las cucMlas y proceder despacio cuesta abajo en ia pendiente. Si la mAquina se para mientras va cuesta arriba, desconectar las cuchillas, poner la marcha atrAs y ir hac_a atrAs despacio. No girar estando en pend_entes s[ no es necesario, y fuego girar despacio y gradualmente cuesta abajo, si es posible. AI cargar o descargar la mAquina, no sobrepase el angulo mAximo recomendado de 15 °. ESPECIFICACIONES Capacidad y Tipo !de Gasohna: DEL PRODUCTO Tape de Aceite API' SG-SL)' SAE 30 (sobre 32°F/0°C) SAE 5W30 (deabajo 32"F/0°C) Capacidad _,ceite: Con Filtro: Sin Filtro: de 56 Oz.!1.65 L 48 Oz./l 4 L Buj[a Champion RC12YC (Abertura: .030"/0.76 ram) Valocidad de Recarrido (MphiKph). Marcha Adelante Arras" Sistema Carga: de Bateria: Tors[6n del Perno de la CuchiI{a: trabajo et_cientes. En el estado de California, la lay exige io anterior (Secci6n 4442 del "California Public Resources Code"). Otros estados pueden contar con otras leyes parecidas. Las leyes federales se aplican en la tierras federales. Su centro de Servicio m_.s cemano tiene disponibie amortiguadores de chispas para el silenciador. (Vea la secci6n de Partes de Repuesto en el manual Ingl6s del dueSo.) 2.50 Galones/9,46 L Regular Sin Ptomo ACUERDOS DE PROTECCION PARA LA REPARACIC)N Congratulaciones per su buena compra. Su nueve producto Craftsman® est& disehado y fabricado para funcionar de mode fiabLe per touches aSos. Pero come redes los productos, puede necesitar alguna reparacibn de tanto en tanto. En este case tenor un Acuerdo de Protecci6n para la Reparaci6n puede hacer[es ahorrar dinero y fast|dies. Compre ahora un Acuerdo de Protecci6n para La Reparacibn y prot6gese de molest=as y gastos inesperados. Un Acuerdo incluye los puntos sigu_entes: , Servicio experto de nuestros 12.000 especialistas profesionales en la reparaciSn. • Servicio ilimitado sin cargo alguno para las partes y la mane de obra sobre todas las reparaciones garantizadas. • Sustitucibn del producto si su producto garantizado no puede set arreglado. • Descuento de110% sobre el precio corriente de[ servicio y de [as partes retativas a[ servicio no cubiertas per el acuerdo; tambi_n el 10% manes sobre el precio corriente de un control de mantenimiento preventive. • Ayuda r_pida per tel_fono -soporte telefbnlco per parte de un representante Sears sobre productos que requieren unarreglo en casa, y ademAs una programaciSn sobre los arreglos m&s convenientes. Cuando se ha comprado el Acuerdo, basta con una Ilamada telef6niCa para programarel servicio. Puede |iamar cuando quiera, diay noche o fljar en linea una cita para obtener el servicio, Sears tiene m&s de 12.000 especialistas profesionates en la reparac_6n, qua tienen acceso a m&s de 4.5 millones de partes y accesorios de ca[idad, 1st 1.0/1,6 2rid 1.4/2,3 3rd 2.1/3,4 4th 3.!/5,1 5th 4.0/6.4 6th 5.4/8,2 0 - 2.9/4,7 3 Amps Bateria 5 Amps Luces Amp/H r: Min. CCA: Mode!e Tamaho: 28 230 UIR 45-55 Ft. Lbs.162-75 Nm FEL|CITAC1ONES per la compra de su tractor. Ha side diseSado, pLanificado y fabricado para darle la mejor confiab]lidad y el mejor rendimiento posible. En el case de que se encuentre con cualquier problema que no pueda solucionar f_.cdmente, haga el favor de ponerse en contacto con un centre de servie[o Sears o con un otto centre de servicio cualificado. Cuenta con representantes bien capacitados y competentes y con las herramientas adecuadas para darle servicie o para reparar este tractor. Haga el favor de leer y de guardar este manual. Estas instruc-ciones le permitir&n montar y mantener su unidad en forma adecuada. Siempre observe las "REGLAS DE SEGURIDAD." RESPONSABILIDADES DEL CLIENTE • Lea y observe las reglas de segundad. • Siga un programa regular de manten_miento, cuidado y use de su tractor. • Siga las instrucc_ones descritas en las secc]ones "Mantenimiento" y '_Jmacenamiento" de este manual. - Utilice prendas de seguridad adecuadas al manejar la m&quma, incluidos (come minimo) calzado de seguridad, galas protectoras y protecciSn auditiva. No utihcepantalones cortes yio calzado abierto cuando corte Eahierba. • Informe siempre a atguien de qua se dispone a cortar la hierba en el exterior. Este es el tipo de profesionalidad con que puede contar para ayudar a alargar la vida del product(} que acaba de comprar, per rnuchos ar_os. iCompre hey su Acuerdo de ProtecciSn para la Reparaci6n! Se aplican algunas limitaciones y exclusiones. Para conocer los precios y tenet m&s [nformacion, Ilarne a| 1-800-827-6655o _DVERTENCIA: Este tractor v]ene equipado con un motor de combusti6n interna y no se debe usar sobre, o cerca, de un terreno no desarrollado cub_erto de bosques, de arbustes o de c6sped, o manes que el sistema de escape del motor venga equipado con un amortiguado[ de chispas que cumpla con las leyes locales o estatales (st existen). Si se usa un amortiguador do ch]spas, el operador debe mantenerlo en condic[ones de SERVIClO DE INSTALACION SEARS Para la instalaei6n profesional Sears de aparatos de casa, puertas de garaje, calentadores de agua y otros irnportantesarticulos para fa casa, en U.S.A Ilamar a 1-800-4-MY-HOME® 35 Hoja de pendiente Llaves Llaves (2) Su tractor nuevo ha sido montado en la f,_brica con la excepci6n de aquellas partes que no se hart montado por razones de envio. HERRAMIENTAS NEOESARIAS PARA EL MONTAJE Etiqueta Un juego de Ilaves de tube facllitar_ el montaje. A continuaci6n se enumeran los tamahos de las Ilaves est__ndar. (t) Llave de 1/2" (2) Llaves de 7/16" Pinzas Cuchillo Medidor de presi6n Cuando en este manual se mencionan los terminos "mano derecha" o "mane izquierda" se refiere a cuando usted se encuentra en la poslci6n de operaci6n (sentado!a detr&s del volante de direcci6n). AJUSTE EL ASIENTO 1_ Sl_ntese sobre el aslento. 2_ Levante [a palanca del ajuste (A) hacia arriba y mueva el asiento hasta que alcance una pos_ci6n c6moda que le perm_ta pres_onar completamente sobre et pedal del em braguei freno 3. Desconecte la palanca para trabar el asiento en la poslciOn. PARA REMOVER EL TRACTOR DE LA CAJA DE CARTON DESEMPAQUE LA CAJA DE CARTON Remueva todas las partes sueltas que est_n accesibles, y las cajas de partes, de la caja de cart6n grande. Co[tar a 1olargo de las lineas de puntos en todos los cuatro paneles de cart6n. Remover los paneles de clerre y apJanar los paneles laterales. • Revise si hay partes sueltas adicionales o cart6n y remuevalas. ANTES DE REMOVER EL TRACTOR DE LA CORREDERA VERIFIQUE 1. Levante LA BATERiA del aslento a la posici6n levantada. AVISO: Ahora puede rodar su tractor fuera de la corredera. Siga las siguientes instrucciones para remover el tractor de la corredera. AVISO. Siesta bateria esta utilizada despu#s del mes y a5o indicado sobre la etiqueta (la etiqueta que se encuentra entre los term=hales), cargue la baterla por un minimo de una hora a 6-10 amps. (Vea "BATERIAt' en la secci6n de Mantenimento de este manual). • ADVERTENOIA. Antes de empezar, leer, entender y segu# todas las instrucciones presentes en la secciOn Operaciones de este manual. Asegurarse que el tractor este en un #,rea bien ventilada, Asegurarse que la zona delante del tractor este libre de otras personas y objetos. Para instale la bateria, y cable de la bateria, realice el procedimjento descrito en "REEMPLAZAR LA BATERIi_' deJ capitulo de Servicio y Ajustes de este manual. 36 PARA HACER RODAR EL TRACTOR FUERA DE LA CORREDERA (Vea la setci6n de la operacibn para la Iocalidad y la funcion de los controles) 1. Levante la palanca de [evantamiento del accesorio a su posici6n m_.s a[ta. 2. Suelte el freno de estac=onamiento presionando el pedal del embrague_eno. 3. Ponga la palanca de carabaos en la pos=c_Sn de neutro. 4. Haga rociar el tractor hac_a delante fuera de [a corredera. 5. Remueva las bandas que sujetan [a protecci6n contra la descarga en contra del tractor. REVISION DE LA PRESION DE LAS LLANTAS Las Ilantas en su unldad fueron inf[adas demasiado en la fz&bricaper razones de envio. La presi6n de las flantas correctas es importante para obtener el mejor rendimiento en el corte, • Reduzca la presi6n de los neum&ticos a la PSI que se =ndicaen estos. REVISION DE LA NIVELACION DEL CONJUNTO Para obtener los mejores resu[tados en el corte, la caja de la segadora tiene que estar nive[ada en la forma adecuada. Yea "PARA NIVELAR LA CAJA DE LA SEGADORA_' en la secci6n de Servic[o y Ajustes de este manual. REVISION DE LA POSICION ADECUADA DE TODAS LAS CORREAS Vea las figuras que aparecen para cambiar las correas de impulsi6n de la cuchilla de la segadora y de movimiento en la secci6n de Servicio y Ajustes de este manual. Verifique que las conreas sigan su paso correcto. REVISION DEL SISTEMA DE FRENOS Una vez que usted haya aprendido a manejar su tractor, verifique que el freno func=one correctamente. Vet "PARA VERIFICAR SI FUNCIONA BIEN EL FRENO" en el cap[tulo de servicio y ajustes de este manual. 37 LISTA DE REVISION Antes de operary de disfrutar de su flatter nuevo, le deseames que reciba e[ meier rendimientoy la mayor satisfaccion de este producto de calidad. Haga e[ favor de revisar la lista a continuacion: t/" Se ban completado todas las instrucciones de montaie. / No quedan panes sueltas en la caja de cart6n. /" La bateria est_ preparada y cargada en forma adecuada. / El asiento ha side ajustado en forma c6moda y apretado en forma segura. / Todas las Ilantas han side infEadasen forma adecuada. (Parafines de env{o, las I}antas se inflaron demaslado en la f_brica.) _f AsegLirese que el conjunto segador este niveiado en forma adecuada, de lade a lade y desde adelante hacia atr&s, para obtener los meiores resuffados en eEcorte. (Las Ilantas tienen que estar infladas en forma adecuada para la nivelaci6n.) vf Revise las correas de impulsi6n y de ta segadora. Asegerese que recorran el paso adecuado alrededor de las poleas y dentro de redes los fijadores de las eorreas. / Revise el alambrado. Fijese que todas las conexiones todavia est6n seguras y que los alambres est_n sujetos en forma adecuada. AI mismo tiempo que aprende a come usar su tractor, preste atenci6n extra a los puntes de oortancia que se presentan a continuaci6n: El ace[te del motor tiene que ilegar al nivel adecuado. /' El estanque de combustibletiene que estar Ileno con gesolina sin plomeregular, nueva y limpia. /" Familiarieese con todos los contro[es - su ubicaci6n y su funci6n. Op6relos antes de hacer arrancar el motor. if Aseg_rese que el sistema de frenos est@en una condici6n de operaci6n segura. Vr Asegurarse de que el Sistema de Presencia del Operador y el Sistema de Funcionamiento Atr_s (ROS) funcionan de mode adecuado (Ver las Secciones de Funcionamiento y Mantenimiento en este manual). Estos s[mbofos pueden aparecer sobre su tractor o en la hteratura proporcionada con el producto. Aprenda y comprenda sus significados. R MARCHA N ATRAS H L NEUTRO ALTO BAJO _ MOTOR MOTOR 6 I\! ESTRAN. GULACION G MOTOR APAGADO R,&.PIDO LENTO (®) FRENO BE ALTURA DE LA LEVANTAMIENTO SISTEMA ENCENDIDO ENMARCHA ESTAC_ONAMIENTO SEGADORA DE LA SEGADORA FUNCIONAMIENTO ATRAS LUCES ENSENDIDAS IRES) COMBUSTIBLE ACCESOR[O DEL E['_BRAGUE ENGANCHADO BATERIA ACCESORIO DEL EMBRAGUE DESENGANCHADO MARC.HA ATRAS MARCHA HACIA ADELANTE PELIGRO, GUARDE MANES Y LOS PIES LAS LEJOS PALANCA DE MANDO CRUCERO MANTENGA EL AREA DESPEJADA PEDALDE FRENO DE EMBRAGUE [ PELIGROS DE PENDIENTES {Veala seccidnde las reglasde segur_da_) PELIGRO _ndtca un peligro que, si no se evita, provoca rnuerte o Eesiones graves. ADVERTENCIA mdic_ un pehgro que, s=no se evtta, puede prevocar muerte o lesiones graves. RUEDA LIBRE PRECAUCII3N un pehgro si no se evita, puede provocarindica leslones l[gerasque, o moderadas. (Solamente para los madelos automatlco) PRECAUC|I3N & No segutr las siguientes Enslruceiones puede provecar hendas o muerte. Los simbolos de arise de segundadse utdtzan para identtficar informaciones de segundad relaWas a pehgros que paedenprovocar la muerte, hendas graves y!o elaSos a la m_.quina. indlca tractor cuando una sduacisn se utthza sin el simbolo que puede provocar daSos de arise, al ylo al motor. SUPERFICIES CALIENTES iadica un pehgro que, st no se evita, puede provocar la muerte, lesiones graves y/o danes a la m_,quina, /_.,_.. FUEGO indlca un pefigro que, s_ no se ewta, puede provocar la muerte, lesiones graves ylo danes a la mdquina. 38 FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL Y LAS REGLAS DE SEGUR1DAD ANTES DE OPERAR SU TRACTOR Compare las tlustraciones con su tractor para familiarizarse con fas ubicaciones de los diversos controtes y ajustes. Guarde este manual para referencia en el futuro. 03078 Nuestros tractores cumplen con los est&ndares de segufidad det American National Standard Institute. (A) PALANCA DEL LEVANTAM]ENTO DEL ACCESORIO -Se usa para levantar, bajar y ajustar el conjunto segador o los dem&s accesorios montados en su tractor (E) PALANCA DEL EMBRAGUE DEL ACCESORIO - Se usa para enganchar las cuchillas segadoras, o Los dem&s accesorios montados en su tractor. (B) PEDAL DEL EMBRAGUE/FRENO - Se usa para desembragar y frenar el tractor y para hacer arrancar el motor, (F) INTERRUPTOR DE IGNICI6N - Se usa para hacer arrancar o hacor parar e[ motor. (G) S JSTEMA DE FUNCIONAMIENTO HACIA ATRAS (ROS) en posici6n "ON" - Permite la operaci6n del conjunto segador o otto accesorio accionado mientras queen rev_s. (C) PALANCA DEL FRENO DE ESTACIONAMIENTO - Asegura el pedal del embrague]freno en la posici6n det freno. (D) CONTROL DE ACELERACION/ESTRANGULACION - Se usa para hacer arrancar controlar la velocidad del motor. (H) INTERRUPTOR DE LA LUZ apaga las luces delanteras. y - Enciende (J) PALANCA DE CAMBIO - Selecciona Iocidad y Eadirecci6n del tractor, 39 y la ve- La operacion de cualquier tractor puede hacer que salten objetos extraEos dentro de sus ojos, |o que puede producir da_os graves en _stos. Siempre use anteojos de aeguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una mdscara de visi6n amplia de seguridad usada sobre las gafas. COMe USAR SU TRACTOR IMPORTANTE: Dejando el interrupter de la ignicidn en cualquier peslci6n otra que "STOP" causar i que la bateria se descargue (muerta). AVlSO: Bajo ciertas condiciones, cuando el tractor est,. parade con el motor andando en vacio, los gases de escape del motor caliente pueden hacer qua el cesped se ponga "caf_." Para eliminar esta pos=bilidad, s_empre pare el motor cuando pare el tractor en __reas con c6sped. PARA AJUSTAR EL FRENO DE ESTAC|ONAMIENTO Su tractor vlene equipado con un interrupter sensor que exige la presencta del operador Cuando el motor esta funcionando, st el eperador trata de bajarse del asiento kin primero aplicar el freno de estac_onamiento, se apagar& el motor. 1. Prestone el pedal (D) del frenolembrague compEetamente y sostenga[o. 2. Jale hacla arnba la palanca del freno de mane (H) y mant6ngala en esa posici6n; suelte gradualmente el pedal de[ embragueifreno (D), y Euego suefte la patanca del freno de mane. El pedal tiene que quedar en [a posici6n de freno. Asegurese qua ef freno de estactonamiento va a sujetar el tractor en forma segura. _I4_PRECAUCI6N: Siempre pare el tractor completamente, seg_n se ha descnto anteriormente, antes de abandonar la postcl6n del operador PARA USAR EL CONTROL DE LA ACELERACION (D) Slempre opere e_ motor a una aceleracl6n completa. • Si el motor functona a una ve[ecidad inferior a la m_,xlma (r&pida), su rendlmiento dismlnuye. • El rendimtente 6ptimo se obtiene a la velecidad m&xima (r#,plda). PARADA CUCHILLAS DE LA SEGADORA • Muevaelinterruptordelembraguedelacceserio a la pesicton "DESENGANCHADO" (I-_t). PAPA MOVERSE HACIA ADELANTE Y HACIA ATR_,S La direccl6n y la velocidad de[ movimtento son contro]adas per medio de la palanca de camblo. (Ir_l) Palanca Del Ern brague Del Accesorio "ENGANCHAR .... {MPULSK)N • ° (1"_) Palanca Del Embrague Del Accesono DESENGANCHADO" DE RECORRIDO Para parar el mecan=smo el pedal del freno/embrague Mueva la palanca de neutro. MOTOR - impu[sor, presione completamente. de cambtos a la posici6n 1. (J) 2. • Mover ta palanca (J) de mando entre la poslciSe de veEocidad media y m&xima (r&pida). AV[SO:Si no se mueve la palanca de mando entre la posict6n de velocidad media y m&xima (r_pida), antes de pararse, se puede causar un "retorno de llama" del motor. • Haga arrancar e[ tractor con el pedal del embrague/freno pres=onado y con la palanca de cambio en la posici6n de neutro (J), Mueva la palanca de cambto a ta posici6n deseada. 3. Lentamente suelte el pedal de embrague/ freno para empezar con el movimiento. IMPORTANTE: Haga que el tractor pare completeamente antes de hacer cambios o de cambiar de engranales. Si no se hace Io anterior tara la duraci6n uttt de su transeje. Gire la [lave de ignici6n (F) a ta posici6n de apagado "STOP" y remueva la Ilave al abandonar el tractor para evltar el use no autortzado. 40 se acor- PAPA AJUSTAR LA ALTURA DE CORTE DE LA SEGADORA La posici6n de la palanca elevadora (A) determina a qu_ altura se cortar_t el c6sped. • Goloque la palanca la altura deseada. elevadora 3. Repita el prcced_miento para el lado opuesto instalando la rueda calibradora en el mismo agujero de ajuste. PARA OPERAR LA SEGADORA Su tractor viene equipada con un interruptor sensor que exige la presencLa det operador, Si el motor est#.funcionando y el embrague del accesorio esterenganchado y el operador trata de bajarse de1asiento, se apagar& el motor. Tiene que rnantenerse sentado completa y centralrnente en el asiento para impedir que el motor vacile o se apague cuando se opere su equipo en terreno disparejo, _,spero o en oerros. 1. Seleccione ta altura de corte deseada. 2. Baje ]a segadom con el control de tevantamiento del accesono. 3. Haga arrancar las cuchil]as de la segadora enganehando el control del embrague del accesorio. PARA PARAR LAS CUCHILLAS DE LA SEGADORA Desenganche el control del embrague del accesorio. • i_PREGAUOI(_N: No opere la segadora sin, ya sea, el recogedor de c6sped comp]eto en ]as segadoras asi equipadas o con la protecci6n contra la descarga (S) en su lugar. en la ranura de La gama de la altura de corte es de aproximadamente 1 a 4 pulgadas. Las alturas se miden desde el suelo a la punta de la cuchilla cuando el motor no est& funcionando. Estas alluras son aproximadas y pueden variar dependiendo de las condLciones del suelo, de la altura del c6sped y del tipo del cesped que se est& segando. • El c6sped promedio debe cortarse aproximadamente a 2-1/2 pulgadas durante la temporada fria y sobre 3 puigadas durante los meses calurosos. Para obtener un c6sped m_.s saludable y de mejor apariencia, siegue a menudo y despu_s de un crecimiento moderado. • Para obtener el mejor rendimiento de corte, el c_sped que t_ene m_.s de 6 pulgadas de aLtura debe segarsedos veces. Hagael primercorte relatLvamente alto; el segundo a la altura deseada. PAPA AJUSTAR LAS RUFDAS GALIBRADORAS Las ruedas calibradoras est_n bien ajustadas cuando se encuentran un poco a distancia det terreno al m[smo t_empo que la segadora est6 a ta altura de corte deseada. Entonces tas ruedas calibradoras mantienen el conjunto segador en posici6n para prevenir el corte raspeo en casi todos Losterrenos. AMISO: Ajuste las ruedas calibradoras con el tractor en una supe_cie nivelada plana. 1. Ajuste la segadora a la aftura de coffeedeseada con ta manilla de ajuste de altura (Vea "PARA AJUSTAR LA ALTURA DE CORTE DE LA SEGADORh_' en la secciOn de Operaci6n de este manual). 2. Con la segadora a la altura deseada para la posic_6n de corte> se tienen que montar las ruedas calibradoras de modo que queden un poco sobre el suelo. Instale las ruedas calibradoras en el agujero adecuado con e] perno con resalto, la arandeta de 3/8, y la tuerca de seguridad de 3i8-16 y apri6telos en forma segura. PARA OPERAR EN CERROS _IIADVERTENCIA: No maneje hacia arriba o hac[a abajo en cerros cen pendientes supefiores 15" y no maneje atravesando ninguna pendiente. Utilice la gula de la pendiente proporcionada en la parte posteriora de este manual, • Escoja la ve[ocidad m#,s lenta antes de arrancar hacia arriba o hacia abajo en cerros. • Evite parar o cambiar la velocidad en cerros. * Si es absolutamente necesario el parar, empuje el pedal del embragueJfreno r_.pidamente a la posiei6n de freno y enganche el freno de estacionamiento. , Mueva la palanca de cambio a primera. Aseg0rese que ha dejado $uliciente lugar para que et tractor pueda rodar un poco cuando vue]va a empezar el movimiento. • Para volver a empezar el movimiento, suelte lentamente eT freno de estacionamiento y el pedal del embrague/freno. • Gire siempre lentamente. PARA TRANSPORTAR • Levante la palanca de levantamiento del accesorio a su posici6n m#.s alta. 41 ANTES DE HACER ARRANCAR EL MOTOR REVISE EL NIVEL DE ACEITE DEL MOTOR El motor en su tractor ha stdo enviado desde la f_.bnca Ileno con aceite de calidad para verano. 1. Revise el aceite del motor con el tractor en terreno nivelado. 2. Remueva Iatapa!varilla indicadora de nivel de relleno del acelte y limpielas, vuelva a insertar la vadl[a indicadora de nivel y atornille la tapa hasta que quede apretada, espere per unos cuantos segundos, remu6vala y lea el nivel del aceite. Si es necesario, agregue aceite hasta que se haya alcanzado ]a marca Ileno (FULL) en la varilla indicadora de nivel. No Io Ilene demasiado. • Pare [a operaci6n en citron fdo, debe cambiar el aceite para poder arrancar mAs fa.cilmente (Vea "Tabla de Viscosidad Del Aceite" en la secci6n de Mantenimento de este manual). • Paracambiarel aceite del motor, vealasecci6n de Mantenimento en este manual. * Cuando empu]e o arrastre su tractor asegerese que [a palanca de camb[o est6 en la posic]6n neutro. • No empuje o arrastre le tractor amAs de cinco (5) MPH. AVISO: Pare proteger el cap6 contra el daSo cuando transporte su tractor en un eami6n o remolcador, asegSrese que el cap6 est@ cerrado y asegurado al tractor. Use los medics aproptados para amarrar el cap6 al tractor (cuerdas, cordeles, etc.)_ REMOLQUE DE CARRETILLAS O OTROS ACCESORIOS Remolque solamente los accesonos recomendados y especificados per el fabricante del tractor, Use sentido com_n cuado este remolcando. Las cargas pesadas, cuando este yendo sobre una pendiente, son pe[igrosas, Ins Hantas pueden perder su tracc_6n con el terreno y pueden ocasionar que plerda el control de su tractor. FUNCIONAMIENTO ATRAS Tu tractor est& equtpado con el Sistema de Funclonamlento AtrAs (ROS). Cualquier tentative del operador de viajar marcha atr&s con el embrague puesto apagar& el motor a menos que la Ilave de ignici6n se ponga en la posici6n de "ON" del ROS. ATENCION: Ir marcha atr_s con eE embrague puesto para co[tar, no es recomendable. Poniendo el ROSen posiciSn "ON", pare permit_r el funcionamiento atr&s con el embrague puesto, se tiene que hacer s61o cuando el operador Io considera necesano pare reposicionar la maquina con el dlsposttivo embragado. No siegue en rev6s a menos que sea absolutamente necesario. USAR EL SISTEMA DE FUNCIONAM[ENTO ATRAS - AGREGUE GASOLINA • Lfene el estanque de combustible. Llene hasta la parte _nferior del cuello de relleno del estanque de gasolina. No Io Ilene demasiado. Use gasol_na regular, sin plomo, nueva y lirapie con el minima de 87 octanes. (El use de gasolina con plomo aumentar& los dep6sitos de 6xido de plomo y carbano y se reductrA ia duraci6n de Ia vAIvula). No mezc[e e] aceite con la gasolina. Pare asegurar que la gasohna utilizada sea fresca compre estanques los cuales puedan ser uttlizados durante los pdmeros 30 d[as. _PRECAUCl6N: LimpJe el acelte o el combusttble derramado. No almacene, derrame o use gasohna cerca de una llama expuesta. Utihce el tractor solamente s_ esta seguro de que no ingresaran n_r_os ni otras personas o animales al Area donde se vaa carter el c6sped. 1. Presionar el pedal embragueifreno haste et rondo y mantenerlo apretado 2. Con el motor en mareha, girar [a Ilave del interrupter de la _gnici6n en et sentido inverse al de las agu]as del reloj haste la posicl6n "ON". 3. Mire hacia abajo y hacia atr__s no s6[o antes de ir marcha atr&s, sine mientras est_ yendo marcha atr_.s. 4. Mover la palanca del cambio en la posici6n atras (R) y soltar despacio el pedal del embragueifreno pare empezar el movimlento. 5. Cuando el use def ROS es m,_s necesario, d@ vuelta ala Ilave de [gnici6n en el sentldo de Ins agu]as del reloj haste ta pos]ci6n "ON". Posm_6n ROS "ON" Motor IMPORTANTE: Cuando se opere en temperaturas per debajo de 32_F (0°C) use gasoline de invierno limpia y nueva pare auedar a asegurar un buen arranque en clime frio. PRECALIClON. Combustibles mezclados con alcohol (conocidos come gasohol, o el use de etanol o metanol) pueden atraer la humedad, la que conduce ala separaci6n y formaci6n de Acidos durante el almacenamtento. La gasoline acldica puede da6ar el sistema del combustible de on motor durante el almacenamiento. Pare evitar los problemas con el motor, se debe racier el sistema de combustible antes de guardarlo per un periodo de 30 alias o m&s. Vac{e el estanque de combustible, haga arrancar el motor y h_tgale functonar hasta que Ins linens del combustible y el carburador queden vacios. La pr6x_ma temporada use combustible nuevo. Vea Ins Instrucc_ones pare el Almacenamiente para mAs informac_6n. Nunca use productos de limpteza pare el motor o pare el carburador en el estanque del combustible pues se pueden producir daSos permanentes. en pos_c]6n"ON" 42 PARA HACER ARRANCAR EL MOTOR AI hacer arrancar el motor per la primera vez o si se ha acabado eLcombustible de1 motor, se necesitar_ tiempo para el arranque extra para mover el combustible desde el estanque hasta el motor. 1. Si_ntase en el sJll6n en la postc_6n de operaci6n, suelte el pedal del embragueifreno y ponga el freno de estacionamiento. 2. Ponga ia palanca de cambio en la posici6n de neutro. 3. Mueva el embrague dot accesodo a la posiciSn desenganchado disengaged. 4. Mueva la palanca de control de la aceleraci6n a la posiciSn de estrangutaci6n. AVISO: Antes de arrancar, lea las Lnstrucciones siguientes para el arranque en clima frlo y templado. 5. lnserte la Ilave en la igniciSn y gire la liave en el sentide que giran las manillas del reloj a la posiciSn de arranque start, y suelte la Ilave tan pronto come arranque el motor. No haga funcionar el arrancador continuamente per m&s de quince segundos per minute. Si el motor no arranca despu6s de intentarlo varias veces, mueva el control de la aceleracL6n a la posicl6n de rApido, espere unos cuantos minutes y trate de nuevo. Si el motor sigue sin funcionar, mueva el control de ta aceleraci6n a [a posiciSnde estranguleci6n y intente de CONSEJOS PARA SEGAR No se pueden usar las cadenas para las llantas cuando la caja de la segadora est,. adjunta al tractor. La segadora debe estar nivelada en forma adecuada para obtener el meier rendimiento al segar. Vea "PARA NIVELAR LA CAJA DE LA SEGADOR_' en ta secci_n de Servicio y Ajustes de este manual. • El lade izquierdo de ta segadora se debe usar para reoorte. • Maneje de mode que tos recedes se descarguen en el Area que ya ha side eortada. Mantenga el _[rea de corte a la derecha del tractor. Esto pmducirA una dLstribuci6n m&s pareja de los recortes y un corte m_s uniforme. AI segar las Area grandes, empiece girando a la derecha de mode que los recortes se descarguen, alej_rldose de los arbustos, cotcos, entradas de automdvites, etc. Despu#s de una o dos vueltas, siegue en ta direcciSn opuesta, haciendo virajes a la izquierda, hasta que termine. Ruevo. ARRANQUE CON TIEMPO TEMPLADO (50 ° Y I10 ° C MAS) 6. Cuando arranque el motor, mueva el control de la ace[eraci6n a [a posici6n de rApido. • Los accosorios y eL embrague ahora pueden ser utihzados. Si el motor no acepta esta carga, vuelva a arrancar el motor para permitirle que se caliente par un minute utiiuzando el estrangulador come describido arriba. ARRANQUE CON TIEMPO FRiO {50 ° Y/10 ° C MENOS) 7. At hacer arrancar el motor, mantenga el control de la aceteraciSn a la posiei6n de estrangulaci6n hasta que el motor se caliente y empieze funcionar maL Una vez que empieze a funcionar real, mueva inrnediatamente el centre[ de Ia aceleraci6n a la posici6n rAp[da. El calentamiento del motor puede tomar a partir de varies segundos a varies minutes (cuanto mas fria es [a temperatura, m_.s largo es el ca[entamiento). • Los accesodos pueden set utilizados durante el periodo del recalentamiento. AVlSO: Si se encuentra a mueha altura (sobre 3000 pies) o en clima frio (per debajo de 32°F/ O°C), la mezcla del combustible del carburader debe ser ajustada para el mejor rendimiento del motor. _ea "PARA AJUSTAR EL CARBURADOR" en la secci6n de Servicio y Ajustes de este manual). 00_72 • • 43 Si el c6sped est_ demasiado alto, se debe segar dos veces para reducir la carga y los posibles peligros de incendio debido a los recortes secos. Haga el primer corte relativamente alto; el segundo a la altura deseada. No siegue el c6sped cuando est& mojado. El c6sped mojado taponar& la segadora y dejar& montones indeseables. Permita que se seque et c_sped antes de segarZo. Siempre opere el motor con una aceleraci6n completa cuando siegue para asegurarse de conseguir un meier rendimiento y una descarga aprepiada de los materiales. Regute [a velocidad de recorrido seleceionando on cambio lo suficientemente bajo para obtener un rendimiento de torte de parte de su segadora y tambi_n ta calidad de1corte deseada. Cuando opere con accesorios, selecciene una velocidad de recorrido que se aconqode al terreno y lepermita obtener el meier rendimiento del accesorio que se est& usando, PROGRAMA DE MANTENIMIENTO ANTES CADA . ..... =_o,o,=,_ _o!f.... TIR i .... V' la pres,&rtd_ los =ra_ta_ C .............. Ump_rlabaterray]ostermina, Revisor L_mp,_ I_ te_=,du_ R _'.tl_'l r e[ n_l d_l acE4e ace_'_ ' de '' 0_recclon meter (c_ el ace,_e OeI motOI (stn fillro) r V _ V_ I1_ Ill,re} VI_I _1_1 V_ e[ hl'_o L_mpmr I_ rOllll_ R _mor0_ua_or _ chlsp_s Camber el_lltrode _ce_te(s!e(_Ulpa{_;, _ Llmp_r V _bla go p_r_ 2 Z L_mpL_r la W_2 0_; at_'e. If:} er',i;larl'll_i_lc, _Jla el llltr_ d6 pa_t _I fdlrO _ al_ I_2 d_ c_mbuskbte IV RECOMENDACIONES LUBRICATION GENERALES La garantia de este tractor no cubre los artioulos que han estado sujetos al abuso o a la negligeno]a del operador. Para reclbir todo el valor de la garanfia, el operador tlene que mantener la segadora seg0n las instrucciones descritas en este manual. _ (_) Accesorio de Grasa de} Arbol (_) Accesorio Hay algunos ajustes que se tlenen que hacer en forrna periodica para pealer rnantener su tractor adecuadamente. At menos una vez coda estacl6n necesarlo efeetuar los adjustes sect=ones de Serviclo y Aiustes de Grasa delde Rodamiento la Rueda / cornprobar si es descrltos en los de este manual. Delantera Una vez al abe, cambie la bujia, limpie o carnbie el filtro de alre y revise si los cuch]llas y las correas estan desgastadas. Una buiia nueva yun flltro de a=re limpio aseguran una mezcla de aire combustible adecuada y le ayudan a que su motor funcione rnejor y que dure m&s. ANTES DE _ 2 _ r eL can_cho _amb_r V" i_11#"' T Camber • V OM la_ _.1_1_ de _.UC_£Eh',_MII_ErO V' v'= , , motor _el cAr.)A TEMPORADI ., _el CaE_br_r_'l Camber la plata CADA ID0 HOFt.AS I _1_1 Ira_seje d_ CADA 50 HORAS F V" le= _1 _nlnamlento CADA 25 HORA_ if V '_°_ A_ll_r/camb_rl_'cut;n_ll_:'d=3 I_segador_ R GABDA HOP_S l/ if Ve r=Im_ la _omm_nde dO pm_ence _'G_13teur el [e _lS{_ma d RC, S R A "_'_ DE USO CADA /_ CHART articulado de] volant ccesono de Grasa del Arbol ) Accesorio "1 de Grasa del 4.-... Rodamiento de I'R "_ la Rueda L,,.."R_ [tel engranaje L_ Plancha/l" de Sector de 1 Direcci6n € ._._ 1 k .__ J _ oelantera _ I_ Motor P[vete de Cambio (_) Grasa de proposlto general @) Refi6rase a la secci6n deI"MOTOR" en Mantenimiento USO 1. Revise el nivel del acelte del motor. 2. Revise la operaci6n 3. Revise la presl6n 4. Verifique operado 5. Revise IMPORTANTE: No aceite o engrase los puntos pivotes, los que tienen rodamlentos de nil6n especla[es. Los lubricantes viscosos atraer_.n polvo y mugre, 1o que acortara la duraci6n de los rodamientos. Si cree que [ubricarse, use solamente un lubricante tipo grafito de poJvo seco en forma moderada. de los frenos. de [as Ilantas. que el sistema y ROS funcionen si hay sujetadores de presencia del adecuatarnente. sueltos. 44 TRACTOR Siempre observe las reglas de seguridad cuando d_ mantenimiento. OPERACI()N DEL FRENO Si el tractor neces,ta m&s de cinco (5) pies para detenerse a la m_ima velocidad at cambio m&s alto en una superficie nivelada, de hormigSn o pavimentada, hay que hacerle el servicio alfreno. Ver "PARA VERIFICAR SI FUNCIONA BIEN EL FRENO" en el capitulo de Servicio y ajustes de este manual. LLANTAS • Mantengatodos los neum_ticos con la presi6n de aire adecuada (Ver la PSi qua se indica en estos). • Mantenga los Ilantas sin gasol, na, aoeite o substanoias quimicas para controlde insectos que pueden dafiar la goma. • Evite Lostocones, los piedras, las grietas profundas, los objetos afifados y etros peligros qua pueden dafiar a los ILantas. AV|SO: Para arregLar las llantas perforadas y p6ra prevenir que tenga |lantas pinchadas a eausa de pequefias fugas, puede comprar el sello para Ilantas de su comerciante de partes de repuesto m&s cercano. Elsello previene que los !lantas se sequen y tambi@n la corrosi6n. SISTEMA PRESENC1A OPERADOR Y SISTEMA FUNCIONAM|ENTO ATRAS (ROS) Asegurarse de que el sistema de presencia del operador y el sistema funcionamiento atr_s funcionen bien. Si tu tractor no funci6n come descrito, reparar el problema inmed=atamente. • El motor no arrancar& si el pedal de embrague/freno est& completamente presionado y el mando del embrague del accesorio est& desconectado: VC:RtFI£:ZStSTEMA PRESENCIA OPEP,ADOR • Cuando el motor est,. en marcha, cualquier tentativa del operador do abandonar el asiento sin haber puesto ei freno de estacionamiento primero, apagar#, el motor. * Cuando el motor est& en marcha y el embrague del accesorie est& conectado, cualquier tentativa del operador de abandonar el asiento, apagar_ el motor. • El embrague del accesorio no tendria qua funcionar nunca si el operador no est& en su asiento. Pomci6n ROS'ON" • Cuando el motor est& en marcha con el interrupterde l]ave del sistema de funcionamiento atr&s {ROS) en la posici6n "ON" y el embrague del accesorio conectado, cualquier tentativa del operador de viajar marcha atr_.s, NO apagar_. el motor. CUIDADO DE LA CUCHILLA Para obtener resultados 6ptimos, las cuchillas de la cortadora deben estar aNadas. Reemplace las cuchillas que est6n gastadas, dobladas o dafiadas. REMOCI(SN DE LA CUCHILLA 1. Levante la segadora a su posLci6n m&s alto para permitir el acceso alas cuchillas. AVISO: Proteja sus manes con guantes ylo envuelva la cuchilla con una tela gruesa. 2. Remueva el pemo de la cuehilla dandole vueltas en el sentido inverse al de las agujas del reloj. 3. Lnstalela nueva cuchilla con el estampado 'qHIS SIDE UP" en la direccion de la eegadora y del conjunto del mandril. IMPORTANTE: Para asegurar la instalaeion apropiada, pesicione et agujero central de la cuchilla con la estrel_a de1 conjunto del mandril. 4. Instate y apriete el perno de la cuchilla firmemonte (Par 45-55 piesllibras). IMPORTANTE: Et pemo especial de la cuchilla es termotratado. Agu_ero Central Eslrella Perno Cuchilla "-' Cucb.i]la Conjuntodel Mandril .._ BATERJA Su tractor cuenta con un sistema de carga de la bateria que es suficiente para el use normal. Sin embargo, si se carga ta bateria peribdicamente, con un cargador de autom6viLes, se prolongar& su duraci6n. * Mantenga la bateria y los term|hales Iimpios. • Mantenga los pemos de la bateria apretados. Mantenga los agujeros de ventilaci6n pequefios abiertos. • Vuelva a cargar de 6-10 amperes per 1 hera. AVISO: La bateria del equipo original de su tractor no becesita servicio. No intente abrir o remover las tapas o eubiertas. No esnecesario afiadir o verificar el nivel del electr61ito. Motor en pos_ci6n"ON" PARALIMPIAR LA BATERiA Y LOSTERMINALES VI_RIFIEZSISTEMA FUNCIONAMIENTO ATR/kS La corresiSn y la mugre de la bateda y de los terminales pueden producir "escapes" de potencia en la bateria. 1. Remueva la protecciSn de los term|hales. 2. Desconecte el cable de la bateria NEGRO primero y luego el cable de la bater[a ROJO y remueva [a baterla del tractor. (ROS) • Cuando eLmotor est,, en marcha con el interrupter de |lave en posiciSn de motor"ON" y el embrague del accesorio conectado, cualquier tentativa del operador de viajar marcha atr&s, apagar& el motor. 45 3. 4. 5. 6. Enjuague la baterla con agua corriente y s6queia Limpie los terminales y los extremes dei cable de la bateria con un cepillo de alambre hasta cjue queden briJfantes. Cubra los terminales con grasa o parafina. Re_nstale la baterfa (Vea "Reemplazar la Bateda" en la secci6n de Servicio y ajustes de este manual). ENFRIAMIENTO 1. Remueva la tapaivanlla indicadora de nivel para relleno del aceite. Tenga cuidado de no permitir que la mugre entre en el motor cuando cambie el aceite 2. Deslice el aceesorio de purga del aceite desde la poslci6n de ensamblaje en el arojarniento de la turbina de[ motor y sol--reiD del motor. 3, 4. Para abnrlo, gire la tapa hacia la izquierda. Una vez que haya vaciado corn pletarnente el aceite, vuelva a colocar ra tapa y girela hacia la derecha hasta el tope. DEL TRANSEJE Mantenga el transeje sin acumulaci6n de mugre o paja que puede restringir el enfriamiento. No trate de limpiar el ventilador o la transm_si6n cuando el motor est_ funcionando o mientras ia transmJsi6n est@ caliente. Posici6n de Ensa ' OORREAS V Revise las correas V para verificar s= existe deterioro y desgaste despu@s de 100 horas de operaci6n y camb_eras si es necesarie. Las corteas no son ajustables. Cambie ras correas si ernpiezan a deslizarse debido al desgaste. Cast 5. MOTOR 6. LUBRICAClON Use solamente ace_te de detergente de alta cafidad clasificado con la clasificaci6n SG-SL de servicio API. Seleccfone la calidad de viscosidad del acelte SAE segt_n su temperatura de operaci6n esperada. 7. ELACEITE DEL LIMPIEZA DE LA REJILLA DE AIRE La rejilla de a_re debe mantenerse sin mugre y paia para ewtar el dared al motor debido al sobrecalentamiento, Limpiela con un cep_llo de alambre o con aire comprimido para remove_ la mugre y las fibras de goma secas, pegadas. SlSTEMA DE ENFRJAMtENTO DE AIRE Los escombros pueden atascar el sistema de enfriamiento de aire de motor. Rernueva la cubierta del sopJador y ]impie el _.rea mostrada para evitar el recalentamiento ', dahos ai motor. MOTOR Determine la gama de Ja temperatura esperada antes de cambiar el aceJte. Todd el aceite debe cumplir con la crasificacJ6n de servicio API SG-SL Rejilla_ Aseg_rese clue eltractor est_ en una superficie nivelada. El aceite se drenara m_s f&cilrnente cuando est_ caliente. Recoja el aceite en un envase Use an medidor en la tapaivarilla indicadora del nivel #ara relFeno del ace_te para revisar el niver. Mantenga el aceite en la tinea de Ileno {FULL) en la varilla indicadora de nivel. Apriete la tapa en el tube en forma segura cuando term_ne. FILTRO DEL AIRE Su motor puede sufrir averlas y funcionar de manera incorrecta con un ftltro del a_re sucio. D6le serviclo al flltro de alre mas a menudo sl se usa en cond_c_ones polvorosas. Vea la manual de la motor. Cambie el aceite despu@s de 50 horas de operaci6n o per Io mends una vez al arid si el tractor se utiliza mends 50 horas el ado. Revise el nivel de! aceite de[ carter antes de arrancar el motor y despues de cada echo (8) horas de use continuado. Apriete la tapa del relreno/ varilla Jndicadera de nivel del ace_te en forma segura cada vez qua revise e! nivel def aceite. CAMBIAR Vuelva a fijar el accesorio de purga del aceite en ef alojamiento de la turbina del motor. Vuelva a llenar el motor con aceJte a trav@s del tube de ra varilla indicadora de nivel para relleno del aceite. Vacieto Ientameote. No Io Ilene demasiado. Para la capaeidad aproximada yea las "Especificaciones de l Producto" secci6n de este manual. FILTRO DE ACEITE DEL MOTOR Cambie el fiitro de ace=to del motor cada temporada ovez po/medio que cambie eJ aceite, si el tractor se usa m&s de 100 horae en un aSo. AVISO: A pesar de que los aceites de muItivissosidad (5W30, 10W30, etc.) mejoran el arranque en cl_ma fflo, estos aceites de multiviseosidad van a aumentar el consume de acelte cuando se usan en temperaturas sobre 32 ° F (0 _ C). Revise el nivel det aceite dot motor m_s a menudo, para evitar un posibte daSo en el motor, debido a que no tiene euficiente aceite. PARA Extensor de drenaje de[ ace_te adecuado 46 _ Limpie el SILENClADOR PUERTO DE LAVADO DE LA CUBIERTA Inspeccione ycambie elsilenciador corroido yel La cubierta de su tractor estd equipada con un amortiguador dechispas (sJ viene equipado) pues de lavado sobre la supefficie que forma pueden crear unpeligro deincendio y/odaSos. puerto parle del sistema de lavado de la cubierta. Se deberia utilizarcadavez que se haya usade eltractor, BUJiA(S) 1. Lleve ettrsctor e un lugar horizonta|y despejade Cambie las bujia(s) al comienzo de cada temde su c6sped, Io bastante cercsde una boca de porada de siega o despu_s de cada 100 horas de operaci6n, le que suceda primere. El too de bujfa y eEajuste de la abertura aparecen en "ESPECIFICACIONES DEL PRODUCTO" secci6n de esto manual. riego come paraquelleguelamangueradeljsrd[n. FILTRO DE COMBUSTIBLE EN LINEA El filtro de combustible debe cambJarse una vez cada temporada. Si ef fiEtro de combustible se tapona, obstruyendo el flujo del combustible hacia el carburador, es necesario cambiar[o. 1. Con ef motor fr[o, remueva el filtro y tapone las secciones de la I_nea de combustible. 2. Ponga el filtro de combustible nuevo en su pesiciSn en la linea de combustible con la flecha seSalando hacia el carburador. 3. Asegdrese de que no hayan fugas en ta |[nea dei combustib|e y que las grapes est@n colocadas en forma adecuada. 4. Inmediatamente limpie toda la gasolina tierramada. IMPORTANTE: Aseg_rese de que la boca de descarga del tractor est_.odentada LEJOS de su case, garaje, eoches aparcados, etc. Quite la boca de ensacado o cubierta de mantfllo si est_.acoplada. 2. 3. 4. Mueva et control del embrague del aeceso='lo ala posiciSn "DESENGANCHADO", ponga el irene de estscionamiento y spsgue el motor. Enrosque el sdaptador de !s boquilla (empaquetado con el manual del opersdor del tractor) en el extreme de Is manguera del jardin. Eche hacia atr_s fa sbrazadera de cierre del adaptador de la boquilla y empuje este en el puerto de tavado de [a cubierte en el extreme izquierdo de la cubierta de la segadora. Sue[re !a abrazadera de cierre pare fijar eFadaptador en la boquil[a. ,_,Manguera Adaptador de Boquilla _ __.,_veart_ode Abrazaders LIMPIEZA Umpie todo material extraSe del motor, la bateria, e| asJento, el puhdo, etc Limpie los desechos de laplaca guia. Los desechos pueden limitar el movimLento dei eje deJ pedal del freno/embrague, [o que har_. que patine la cerrea y que se pierda la tracci6n. _PRECAUCI6N: Ewte todos enganche y las piezas m6viles. los puntos IMPORTANTE: Tire de la manguera pare asegurarse de que la conexi6n est& bien fija. 5. 6. de Pedal De! EmbragueiFreno r Parle ,I SISTP.MA PICADERO, DE '2"__ DIRECCI_)N, SALA_, GUARDABARROS Y ; _ SEGADORANO MOSTRADOS _ /_ PRECAUGION: PUI_TOS D F J ENGANCHE I Mantenga las superficies pul(das y las ruedas sin derrames de gasolina, aceite, etc. Proteia las superficies automotriz. pintadas con cera tipo Abra la Ilave del ague. Desde la posici6n del operador del tractor, vuelva a arrancar el motor y ponga Is palsnca de ace[eraci6n en la posici6n "Fast" (rdpldo). IMPORTANTE: Vuelva a comprobar la zone pare asegurarse de que est& despejada. 7. Mueva el control del embrague del accesono s la posicibn "ENGANCHAR". Mant6ngase en la posici6n del operador can la cubierta de corte acoplada hssta que la cubierts est_ limpia. 8. Mueva el control del embrague del accesodo a la pos_c_6n "DESENGANCHADO". Gire la llave de encendido s Is posici6n STOP pare apagar el motor del tractor. Cierre la flare del ague. 9. Tire hacis atr_=s ]a abrazadera de cierre del adaptador de la boquiUa pars desconeotar el adaptador del puerto de lavado de la cubierta. 10. Lleve el tractor a uns zone secs, preferentemente de cemento o pawmentada. Mueva el control del embrague dei sccesor[o s [a posic_6n "ENGANCHAR" pare quitar el exceso de ague y ayudar s que se seque antes de gusrdsr el tractor. _ADVERTENCIA:: Si el accesorlo de lavado est& rote o no est,. Ud. y otras personas estar._n expuestos a que la hoja les lance aquellos objetos con los que entre en cogtscto. Sustituya inmedlatamente et accesorlo de lavado rote o que falta antes de velvet a user la segadora. No recomendamos que se utilice una manguera de jardin o ague a presibn pare limpiar e} tractor a no ser que el motor y la transmisi6n est@n cubiertos para preteger[os del agua. El agua en el motor y la transmisibn aeortan la vida _til del tractor. Utilizer airs compdmido o un sepJador de hojas pare remover hiefba, hojas y basura del tractor y eortac_spedes. Tape todos los orHlcios de Is segadora nee y tuercas de seguridad. 47 con per- _, ADVERTENCIA:PARA SERVICIO O DE HACER 1. 2. 3. 4. 5. 6 EVITAR AJUSTES: LESIONES LA CORTADORA DE I. Suelte ei embrague poni_ndolo en la posici6n "DISENGAGED" ("DESACTIVADO"). 2. Baje la palanca etevadora pos[ci6n de m&s abajo. 3 Ruede ia correa de polea del motor (M) y fijadors de la correa (G). Retire el resorte de sujeci6n (K), deshce la abrazadera (L) hasta quitarla, y saque a presiSn la guia de la caja (P) hasta que se salga del soporte. 5. 6. 7. ANTES DE DAR CUALQUIER Presione ei pedal de[ embragueifreno completamente y aplique el freno de estac_onamiento. Ponga la palanca de cambios en la posici6n de neutro. Ponga el embrague def accesono en la poslc_6n desenganchado (DISENGAGED). Ponga la tlave de igniclSn en ia posici6n de apagado (STOP) y remu6vala. Asegt3rese que las cuchillas y que todas tas partes movlbles se hayan detenido comp[etamente. Desconecte el alambre de la buj{a y p6ngalo en donde no pueda entrar en contacto con @sta. PARA DESMONTAR ClaSPED 4. SERfAS, de montaje a la IMPORTANTE: un accesorio dife- INSTALE LA SEGADORA Asegflrese de que el tractor se encuentre en una superfic_e n_velada, y ponga el freno de mano 1. Haga descender la palanca elevadora a su posicl6n mas baja ,_ Retire el resorte del cable del embrague (Q) del brazo det engranaje (R). Desconecte ta pieza de uniSn anterior (E) de la eortadora - retire el resorte de contenci6n y la arandela. Por uno de los lados de la co_adora, desconecte el brazo de suspens_Sn de la cortadora (A) del chasls y la pieza de uni6n posterior (C) de Ja barra posterior de la cortadora (D) - retee los resortes de contencion y las arandelas. SI se monta rente del cortac6sped al tractor, hay que qintar el estribo frontal (E) y los estrlbos traseros de elevaci6n (C) del tractor y enganchar el resorte de embrague (Q) en la guia del cable en el borde frontal del salpicadero m&s bajo. CUlDADO: La palanca elevadora funciona a resorte. Suj_tela con fuerza, hagala descender lentamente y tr&nquela en la posiciSn m&s baja. NOTA: Cerci6rese de que los brazos de suspensiSn de los ]ados de la segadora (A) esten dlrigidos hac=a adelante antes de desiizarla por 2. Deslice la SEGADORA por debajo del tractor 3. hasta que quede blen cent_ada debajo de _ste FIJE LOS BRAZOS DE SUSPENSION LATEPALES Ubique (B) que tractor, _1_ CUlDADO: Una vez que se desconecten las piezas de uni6n posteriores, ]a palanca elevadora funcionara a resor_e. Sujete con fuer-za la palanca efevadora al cambiarla de posici6n. 8. Deslice la cortadora por debajo del lado derecho del tractor. 48 DE LA CORTADORA CA)AL CHASIS el orificio del brazo encima de la clavija hay en la parte exterior del chasis del y fije[o con u na resorte de contenciSn. Realice el mismo procedimiento en el otro Eadodel tractor. 5. FIJE LAS PIIEZAS DE PROPULSION POSTERIORES (C) - Levante la parte posterior de la cort_dora, ubique la ranura de la pJeza de uni6n (D) por encima de ta clavija qua hay en la barra posterior de la cortadora y fijela con una arandela y un resorte de contencion. 4. 6. 7. 8. 9. Retire e[ resorte de sujecJSn (K), deslice la abrazadera (L) hasta quitarla, y saque a presi6n la gu{a de la caja {P) hasta que se salga del soporte. 10. lnstale la correa pas&ndo[a por encima de la polea del motor (M) y fijadors de la correa (G). IMPORTANTE: Verifique qua la correa encaje bienen todas las ranuras de las poJeas de la cortadora. 11. Suba la palanca elevadora a la posicidn de m_s ardba. 12. Si es necesario, aiuste Jasrueditas del calibre antes de poner en funcionamiento la cortadora, como se ilustra en el cap[tu[o de Manejo de este manual. FME LA PIEZA DE UNION ANTERIOR (E) - Trabaje por el lado izquierdo de] tractor. Introduzca el extrerno de la barra de la pieza de uniSn por el onficio anterior de la barra de suspensi6n anterior del tractor (F). Introduzca el otro extremo de la pieza de uniSn (E) en el orificio que se encuentra en la barra anterior de la cortadora (14), y fljelo per medio de una arandeJa y un resorte de contenci6n (J). Retire el resorte der cable del embrague (Q) del brazo del engranafe (RI. 49 PARA NIVELAR LA SEGADORA 5. AsegSrese de que los neum_.ticos est_n inflados a la PSF que se indlca en estos. Si est&n demasiado iafledos o poco inflados, el c_sped no le quedar& bien cortado, Eo cuai pedrO. Ilevarlo a pensar que la SEGADORA no est,. bien regulada. REGULACION VISUAL DE LADe A LADe 1 Sitodos los neum_ticos est&n correctamente inftados y et c_sped parece haber quedado cortado desparejo, determine que lade de la cortadora est,_ cortando m&s al ras. Con una [lave inglesa de 3/4" o de cahbre regulabie, haga g_rar bacia la izqu_erda la tuerca de a]uste de la pteza de unthn (A) para bajar _ado tzquierdo la cortadora, o bien h_.gala girar hacia lade derecho la derecha para su bid& NOTA: Cada vueJta eompleta de Ia tuerca de ajuste har__ variar la altu ra de la cortadora aproxi- Vuelva a verificar las medidas y ajuste nuevamente, en case necesario, hasta que ambos lades queden iguales. AJUSTE DE DELANTE A ATR._,S IMPORTANTE: El piso debe quedar Iado de lade a lade. bien hive- Para que el c#sped le quede perfectamente cortado, las cuchillas de la cortadora deben ajustarse de tal manera que la punta anterior quede 1/8" a 1/2" m&s abajo que la punta posterior cuando la cortadora se encuentre en su posic_6n m&s a[ta. 2. Haga girar ]a tuerca hama Ja derecha para subtr la segadora _a_seGUIDADO: Las guantes cucMlas o son afiladas. cuchilProtelas manes con envuelvalas las con tela gruesa, o bien haga ambas cosas. • Suba la SEGADORA 3. Pruebe la regulaci6n realizada cortando clasped que a,3n no haya cortado y observando c6mo queda. VueJva a ajustar, en case necesario, hasta obtener resultados sat_sfactorios. REGULACION DE LA PRECISION DE LADe A LADe 1_ Con redes los neum&t_cos correctamente _nflados, estacione el tractor a nivel del suelo o en la entrada a la casa. CUIDADO: Las cuchlllas son affiadas_ Prot_jase Ias manes con guantes o envuelva las cuchillas con tela gruesa, o bien haga ambas cosas. 2. Suba la SEGADORA a la poslct6n m_s alta_ A ambos lades de la cortadora, ubique la cuchil[a hacla un lade y mida la dtstancia (A) que hay entre el borde inferior de la cuchilla y el suelo. DJcha distancla debe ser Ia misma a ambos lades. 4. En case que sea necesano realizar un aluste, lea los paso 2 de las instrucciones de Regulaci6n Vtsual que aparecen m_.s arnba. mAs a[ta. • Si la punta anterior de la hoja de la cuchilla no est,. 1/8" a I/2' m_.s abajo que la punta posterior, dJrijase a Ia parte de aclelante del tractor. • Con una Ilave inglesa de I1/16" o de calibre regulable, afloje la tuerca A, d&ndole varias vueitas para despejar la tuerca de ajuste B. • Con una Ilave mglesa de 3/4" o de calibre regulable, haga girar Ia tuerca de ajuste de la pieza de uni6n anterior (B) en sentldo horado (ajustar) para elevar la parle de adelante de la cortadora, o bien en sentido antihorario (aflojar) para bajarla. Haga girar la tuerca hacia la izqt_ierda para bajar la segadora 3. a la posici6n • Ubique cuatquiera de las hojas de la cuchilla de tal manera que la punta quede apuntando directamente hacia adelante. M[da la distancia (B) que hay entre la punta anterior y el suelo y entre la punta posterior y el suelo. ..r Ajuste [a tueTca de regulacioa de altura B para levantar Ia segadora Allele la tuerca de regu]act6n de altura B para bajar la segadora ,ie la tuerca A primero NOTA: Cada vuelta cornp[eta de la tuerca de ajuste bar& variar la aftura de la cortadora II8". • Vuelva a veriflcar las medidas y ajuste naevarnente, en case necesarie, hasta que la punta anterior de Ia hoja de la cuchilla quede 1/8" a I/2" mAs abajo que la punta posterior_ • Mantenga en la posici6n la tuerca de ajuste per medio de una Ilave ingfesa, y apriete bien la tuerca contra dtcha tuerca de ajuste. 5O CONTROLAR Y AJUSTAR PARA CAMBIAR LA CORREA DE IMPULSION DE MOVIMIENTO EL FRENO Si et tractor exige m_s de einco (5) pies para pararse auna veJocidad m__s alta en el carnbio m_s alto en una superficie nivelada de hormig6n seco o pavimentada, entonces se debe eontrolar y ajustar el freno. CONTROL DEL FRENO 1. Estacione el tractor en una superficie nivelada. Pongae]freno de mane. En caseque necesiteasistencia, del lade de abajo del apoyapi_s izquierdo hay una guia pr_.eticaparael montaie de la correa. DESMONTAJE DE LA CORREA 1. Desmonte la segadora (Vor "PARA DESMONTAR LA SEGADORh:' erl este capitulo del manual). NOTA: Observe bien toda la correa de impulsiSn de movimiento, asl come tambi@n ia posici6n de tas guias y los dispositivos de protecci6n o guardacorreas. 2. Retire la correa del pi56n estacionado (A) y del pi56n de ernbrague (B). 3. Jaleel cabledelacorreahacialapartedeab'&s del tractor, Retire la correa movi_ndola hacia arriba desde la poiea de entrada de[ eje (D). 4. Retire la correa movi_ndola hacia abajo desde ta polea det motor (E). 5. Deslice la cerrea hacia la parte de atr_.sdel tractor, rotfrela del dispositivo de direccibn (F') y s_.quola de[ tractor. Aparcar el tractor en una superficie nivelada de hormig6n seco o pavimentada, pres[onar el pedal dei freno hasta el rondo y accionar el freno de estac_onamiento. 2. Ponga la palanca de cambios en punto muerto. Las ruedas traseras tiene que bloquearse y patinar cuando se intenta empuiar hacia adelante el tractor manualmente. Si [as ruedas traseras giran, es necesario las zapatas. ajustar el freno o sust[tuir PARA CAMBIAR LA CORREA DE IMPULSION DE LA CUCHILL.A SEGADORA La correa de impulsi6n de [a cuchilla segadora se puede cambiar sin herramientas. Estacicne el tractor en una superficie niveJada. Enganche el freno de estacionamiento. REMOCI6N DE LA CORREA 1. 2. MONTAJE DE LA CORREA 1. Pase laeorma nueva desde la parte de atr&s a la parte de ade[ante de] tractor, per encirna de la p|aca de direccibn (F) y de| v&stago del pedal de embrague /freno (G). 2. Jale [acorrea hacia laparte deadelante del_'actory p&selaporencima do la poleade[ motor (E). 3. Jale la correa hacia la parte de atr&s del tractor. Con touche cuidado, dirljala hacJaabaje y p&sela alrededor de ia polea de entrada al eje (D). AsogSresede que la Correaencaje dentro del dispositivo de protecci6n o guardacorroa. 4. Pase la correa a trav6s del pi56n estacionario (A) y del pifi6n del embrague (B). 5. Aseg_rese de que la correa encaje en todas las ranuras de [as poleas y en todos los deles y protecciones. 6. Instale la SEGADORA (Ver"PARA INSTALAR LA CORTADOFIA'en este capitulo del manuaJ). Rernueva ta segadora de[ tractor (Vea"PARA REMOVER LA SEGADOR/_' de esta secci6n de este manual). Haga sa[ir la correa de las poleas del mandriF y de las poleas de guia. 3. Tire la correa alej_ndola de la segadora. INSTALACION DE LA CORREA 1. 2. 3. Haga redar la correa alredeor de ambas poleas del mandrin y de las poleas-gulas. Aseg_rese las correas ester en todas las ranuras de las peleas y al interior todas las gu]as de ]a correa. Instale la segadora (v_a" PARA INSTALAR LA SEGADORA " on esta secci6n de este manual). Po|ea d_l Mandril Polea del Mandril 51 REGULACION DE LA PALANCA DE VELOC|DADES NEUTRO DEL CAMBIO MECANICO IMPRESION / INCLINACION DELANTERAS Elcambio mer__.&n=co con d=ferenc_al y traccisn anterior tiene qua estaren posiciSn neutro cuando la relativa palanca est,. en posici6n {cierre met&lice La regulacion ya est,. predefinida per Ia Casa constructora, pero si es necesario efectuar m__s regulaclones, preceder de la siguiente manera: La irnpresi6n e mchnacl6n de _as ruedas delanteras de su nuevo tractor vienen asi de _brica y son normales. La impreslsn y la inclinaci6n de las ruedas delanteras no son regu[ables. En case que se produzca algt_n daSo qua afecte la impresldn o ra inclinaci6n de las ruedas delanteras tal come vinleron de fabrica, p6ngase en contacto con un centre de serv_c=os Sears u otro centre de servicios autorlzado. 1. Asegurarse queeFcambio mec&nico con diferencial y tracc=Sn anterior est_ en posic_Sn neutro. AM|SO: Cuando las ruedas posteriores del tractor se mueven libremente, et cambio mec_nico est& en neutro 2. Soltar el perno de regulac=Sn en la parte anterior de la rueda posterior derecha. 3. Colocar neutro. ta palanca de veloc=dades 4. Apretar a rondo el perno de regulaci6n. PARA HACER UNA BATERiA en posic_6n Neutro Cier_e 41co 1. 2. 3. PARA 2. Conecte un extreme del cable NEGRO con el terminal (C) NEGATtVO (-) de una bater{a comp[etamente cargada. 3. Conecte el otro extreme del cable (D) NEGRO con un buena CONEXION A TIERRA DEL CHASIS, alejado del estanque de combustibIe y de 3a bater[a. PARA REMOVER LOS CABLES, INVIERTA EL ORDEN Bloquee el eje en forma segura. Remueva Ja cub=erta del eje, el anillo de retenci6n y las arandelas para permitir la remociSn de las ruedas (la rueda trasera contiene una Ilave cuadrada - no la pierda). Repare la Ilanta y vuc_Evala a montar. Arandelas 1. E_ cable NEGRO primero del chasms y luego de la bateria completamente cargada. 2. Ei cable ROJO al _ltimo de ambas baterias. del eie Llave Cuadrada (ru_, trasera solamer_e) CON PARA ADJU NTAR LOS CABLES DE EM PALME 1. Conecte cada extreme de[ cable ROJO con et terminal (A-B) POSITtVO (+) de cada bater[a, preocup&ndose de no hacer cortocircuito en el chasis. Velocidades PARA REMOVER LAS RUEDAS HACER REPARACIONES EL MOTOR ,_ADVERTENClA: I_as baterias de _cido-plome generan gases exploswos. Mantenga las chispas, las llamas y los materiales para fumar alejados de las baterias. Siempre use una protecc=dn para los ojos alrededor de las baterias. Si su bateria est& demasiado baja come para hacer arrancar el motor tiene que volverse a cargar. (Vea "Bateria" en la seccidn de Mantenimiento de este manual). S= se usan "cables de empalme" para un arranque de emergencia, s_ga este proced=miento: ]MPORTANTE, Su tractor esta equipado con un sistema de 12 volts. El otro vehlculo tambi_n t_ene qua tener un sistema de 12 volts No use la bateria de su tractor para hacer arrancar a otros vehlculos. AVlSO: Desplazar el plane de trabajo de la segadora hasta la posiei6n m_is baja para aumentar el juego al fin de acceder al perno de regulaci6n. Palanca de Velecidades de[ Cambio ARRANCAR BAJA DE LAS RUEDAS -_' AVISO: En las ruedas traseras solamente' alinee las ranuras en el cube de la rueda trasera en el eje. Inserte [a Ilave cuadrada. 4. Vuelva a colocar las arandelas e inserte el anil[o de retenciSn en fo_ma segura en la ranura del eje. 5 Vue[va a colocar la cubierta del eje. AVISO, Para arreglar las Ilantas perforadas y pera prevenir que tenga Ilantas pmchadas a causa de pequeSas fugas, comprar de su commerciante Sears y utiJizar el sel[o para flantas. Elsel[o prevjene qua las Ilantas se sequen y tambi6n la corrosiSn. £Sater[a D6bil o Descargada 52 Bateria Oompletamente Cargada REEMPLAZAR LA BATERIA ENTRECIERRE Y RELES ,di_ADVERTENCIA: No haga cortomrcuitc con los terminales de ]a bateria al permitir que una liave de tuerca o cualquier eve objeto entre en contacto con ambos terminales a la misma vez. Antes de instalar la baterla remueva las pulserasde metal, los relojes de pulsera de metal, los anillos, etc. El terminal positive tiene que conectarse pdmero para evitar las chispas debido a la conexi6n a tierra per accidente. El alambrado suelto o dahado puede producir e] real funcionamiento de su tractor, o que deje de funcionar, e le impida el arrancar. • Revise el alambrado. 1. Levante e[ asiento a la posim6n elevada. 2. Remueve la protecci6n de los terminates. 3. Deseonecte ef cable de la bateria NEGRO primero y luego el cable de la bater[a ROJO y remueva la bateria del tractor. 4. Instale la nueva bateria con los t6rminos en misma posici6n come la baterfa vieja. 5. Reemplazamos cubierta terminal. 6. Primero, conecte el cable de la bateria ROJO con el terminal positive (+) con el perno hexagonal y la tuerca seg_n se muestra. Apri6telos en forma segura. 7. Conecte el cable de conexiOn a tierra NEGRO al terminal negative (-) con el perno hexagonal y ta tuerca que queden. Apri6telos en forma segura. 8. Cerramoslaasiento PARA REMOVER EL CONJUNTO DEL CAP6 Y DEL ENREJADO 1. Levante el cap6. 2. Desabroche el eonector del alambre de las Iuces delanteras. 3. P_rese delante deFtractor. Agarre el cap6 en los lados, inclinelo un poco hacia el motor y s_quelo del tractor. 4. Para volver a instalar el cap6, asegOrese de volver a conectar el conector0iei alambre de las luces. PARA CAMBIAR EL FUSIBLE C&mbielo per un fusible ripe enchufable de 30 amps, tipo autemotriz. El suietador del fusible esta ubiCado detr&s de] tablero. Capo Conector del aJambre de las Luces Base as Del As_ento Oubierta Termina] Tuerca Gable Negro (negative) MOTOR Pemo PARA AJUSTAR EL CABLE DE LA ACELERACION _ DE CONTROL El control de la aceleraci6n ha side preaiustado en la f&brica y no debeda necesitar ajustes. Revise los ajustes que se describen a continuaci6n, antes de so[tar el cable. Si el ajuste es necasario, yea de rnanua| de motor, PAPA AJUSTAR EL CONTROL DE ESTRANGULACION PAPA CAMBIAR LA BOMBILLA DE LA LUZ DFLANTERA El control de laestrangulaci6n ha side preajustado en la f&brica y no deberia necasitarajustes. 1. Levante elcap6. 2. Tire elsujetador de la bombilla fuera del agujero en la parte trasera del enrejado. 3. Gamble JabombJlla en el sujetador y empuje el sujetader de la bomb]lla, en forma segura, hacia atr&s en el agujero en la parle trasera del enrejado. 4. C]erre el cap6. PAPA AJUSTAR EL CARBURADOR El carburador ha side preajustado en la _brica y no deberla necesffar ajustes. Sin embargo, se pueden necesitar ajustes de menor importancia para compensarper Jasdfferenciasen el combustible, temperatura, altura o carga. Si el carburador necesita ajustes, yea de manual de motor. 53 MOTOR lnmediatamente prepare su tractor para el a[macenamlento al final de la temporada o si el tractor no se va a usar per 30 dias o m_s. SISTEMA DE COMBUSTIBLE BATERiA IMPORTANTE: Es important evitar que se forman depositos de goma en partes fundamem tales del sistema de combus-tible tales come e] carburador, el filtro del combustible, la manguera del combustibles mezclados con alcohol (conecido come gasohol o que tienen etanol o metanol) pueden atraer humedad, 1o que conduce a [a separaciSn y a la formaci6n de acudos durante elalmacenam_ento. La gasolina acidica puede daffar el slsterna de combustible de un motor durante el penodo de almacenamiento. • Vaciar el dep0sito del carburante poniendo en marcha el motor y dej&ndolo funcionar hasta que el carburante termine e[ carburador est_ vacio. • Nunca use los productos para limpieza del carburador o de[ motor en el estanque de combustible pues se pueden producir daf3os permanentes. • Use combustible nuevo [a pr6ximatemporada. AVISO: El estabilizador de eombushble es una alternat=va aceptable para reducer a un rain=me Ea formaciSn de dep6sitos de goma en el combustible durante el periodo de almacenamiento. Agregue estabilizador a la gasolina en el estanque de combustible o en el envase para el a]macenamiento. Siempre siga ]a proporci6n de mezcla que se encuentra en el envase del estabilizador. Haga funcionar eJ motor per 1o menos 10 minutes despu6s de agregar e[ estabilizador, para permitir que _ste Ilegue al carburador. No vaciar la gaso[ina del estanque de gasolina y el carburador si se est'. usando estabihzador de combustible. • ACEITE ,L(_.DVERTENCIA: Nunca a[macene e[ tractor con gasohna en el estanque dentro de un eddteio en donde los gases pueden alcanzar una llama expuesta o una chispa. Permita que el motor se enfrie antes de almacenarlo en cualquier recinto privado TRACTOR Cuando el tractor se va a almacenar per cierto per[ode de t_empo, limpiela cuidadosamente, quite toda la mugre, la grasa, las hojas, etc. Gu&rdela en una &rea limpia y seca. I. 2. Limpie rode el tractor (vea "LIMPIEZ_._' en la secciSn de Mantenimiento en este manual). Inspeccione y cambie las correas, si es necesane (vea las instrucciones para el carnbio de las correas en la seccl6n de Servicio y Ajustes de este manual)_ 3. Lubdquelo, segrJn se muestra en la secciSn de Mantenimlento de este manual. 4. AsegOrese quetodas lastuercas, los pernos y los tornillos esten sujetados en forma segura. ]nspeccione las partes movibles para verfficsr si hay daffo, rotura o desgaste. C&mbieEas si es necesario. 5. Retoque todas superficies pintadas oxldadas o picadas; aplique lija antes de pintar Cargue la bater[a completamente antes de guardarla. • Despu6s de cierto periodo de tiempo en almacenamiento, la bateria puede necesitar volver a cargarse. • Para ayudar a evitar la corrosi6n y las fugas de potencia durante largos perlodos de almacenamlento, se deben desconectar los cables de la bateria y se debe iimpiar cuidadosamente (yea "PARA LIMP1AR LA BATERIA Y LOS TERMtNALES" en la secci6n de Mantenimien• rode este Despu6s nectados entrar en bateria DEL MOTOR Drene el aceite (con el motor caliente) y c_.mbielo con acelte de motor hmpio. (Vea "MOTOR" en la secci6n de Mantenimiento" de este manual.) ClLINDRO(S) 1. 2. 3. manual). de hmpiarla, deje los cables descoy pSngalos en deride no puedan contacto con los term[nales de la 4. Remueva la(s) bujia(s). Vacie una onza de ace_te a tray,s del agujero(s) de la bujia en el cilindro(s). Gire la Ilave de ign_c=6n a [a posici6n de 'mrranque" (Start), per unos cuantos segundos para distnbuir el aceite. Cambie per bujia(s) nueva(s). OTROS • No guarde la gasolina de unatemporada alaotra. • Camble el envase de la gasolina si se empieza a oxidar La oxldaclSn y/o la mugre en su gasolina producir&n prob_emas. • SI es poslble, guarde su unidad en un recinto cerrado y cRbzala para protegerla contra el polvo y la mugre. • Cubra su anidad con un forro protector adecuado que no retenga la humedad. No use pl,_stico_ E[ pl_stlco no puede respirar, Io que permite la formaciSn de condensaci6n, Io que preducir__ [a oxidaciSn de su unidad. IMPORTANTE: Nunca cubra el tractor mientras el • Si se remueve la bateria del tractor para el a[macenarniento, no la guarde directamente sobre concrete o sobre superficies h6medas. meter y las areas de escape todavta estan calientes. 54 IDENTIFICACION DE PROBLEMAS: Vea la secci6zl apropiada en el manual a menos que est_ didgido a un centre de servlcio Sears. PROBLEMA CAUSA No arranca t. 2 3 CORRECC|ON S'i'ncombustible. Motor sin la "ESTRANGULAGION" (CHOKE) adecuada. Motor ahogado. 1, 2, Bujia male, Filtro de aire sucre. F=ltrode combustible sucio. Agua err el eombustib[e, 4_ s. 6 Cambia la buj[a. Limpie/cambie el "_ltrode atre. Cambie el fi[tro de combustible. 7, Vaciar el estanque de combustible y el carburador, vuelva a Ilenar el estanque con gasohna nueva cambie el fi[tro de combustib]e. Alambrado suelto 8. Revise teda el alambrado. Carburador desajustado. 9 Vea "PARAAJUSTAR EL CARBURADOR" en la secclSn de Sarvicioy Ajustes. 10. Pongase en contacts con un centre de servieio cuallficado "SEARS". 3, Llano el estanque"_te combustible. Vea "PARA HACER ARRANCAR EL MOTOR" en Ia secci_,n de operac{#,o, Espere varies minutes antes detratar de arrancar. !4 ;5 7 Dificil de arranger 10, V_lvu[as del motor desajustadas. 1 Filtro de aire sueio, 1 Lirnpie!camb=e el filtro de aire. 2 Bujia male, 2. Cambie la buiia. 3 4 Bateria baja o descargada. Filtro de combustible sums. 3 4 5. Combustible reacts o sucio. 5 Vaciar el estanque de combustible y vue[va a Ilenado con gasoiina nueva. 6 Alambrado 6 Revise todo e[ alambrado. 7, Carburador 7. Vea "PARA AJUSTAR EL CARBURADOR" on la seccldn de Servicio y Ajustes, 8 Pongase en contacts con un centro de sewicio cualificado "SEARS". 1, Presione el pedal del freno. V_lvutas Elmotor |avue[ta no El motor Isuena pero Ino arranea o dahado. L 2 sue[to o daSado. desajustado. de[ motor desajustadas. Pedal del freno no presionado. I Elembraguede[accesodoest_,enganchado. i Vu_ivaacargarocambielabateria. Cambte el filtro de combustible. 2 Desenganche el embrague del accesono. 3_ 4. Vuelva a cargar o cambie [a bateria. Camble el fusible. 3 Batefia baja 0 descargada. 4, 5 Fusible quemado. Terminales de re bateda corroldos. _. Alambrado suelto 0 daSado. 5 6, Utopia los terminales de la bateria. Revise tsde el alambrado. 7, 8 lnterruptor de la ignici6n fallado. Selenoide o arraneador fallados. 7. Revise/camble el interrupter de laigmctSn. a. Revtse/cambie el solenoide 0 arrancador. 9 Interrupter(as) qua exige(n) la presencia del operador fallado. g Pongase en contacts con un centro de servicio cualificado "SE.ARS". Bateria baja o descargada Termina[es de la bater_a corroJdos, 1 2, VueJvaa cargar o cambie la baterla. Utopia los terminales de la bater[a, Alambrado suefto o dahade. 3 Rewse teals el alambrado. So]enoide o arrancador fal[ados_ 4. Reviselcambie e[ solenoide o arfancador. 2 ': 3. 4, 55 IDENTIFICACION Vea la seccibn DE PROBLEMAS: apropiada en el manual a menos PROBLEMA CAUSA P_rdlda 1 Carla 2 Ace[eram6n GULACION" 3 AcumulaciSn de c_sped, debalO de Ja segadora. 4 Filtro de aire sucre. 5 Nivel de aceite 6 BuJia fallada. 7 Fdtro de combusttbls 8 Combustible de fuerza P_rdida [uerza de Agua que est_ dirigido mucho c_sped, muy r_pido. en la posicion (CHOKE), de "ESTRANhojas bajo!aceite rancio y basura sucio. 1. Eleve la alt ura de corte/_'eduzca 2 Ajuste 3. L=mp=e [a parte segadora. =ofenor de la cajade 4 Limple/camble el fdtro de aire. 5 Revise 6 Limpie y vue!va a ajustar la abertura eambte la bu_a. Cambie el 51tro de combustible. sucio. 7 o sucio 6 en el combusttble. Alambrado de la bujia Rejill_aletas el hive! de acedeicambte sucias. Limp_e las repllaialetas Dmpieicambie Alambrado suelto Revise o daSado. DOR" V_lvulas del motor des_justadas. Cuchilta desgastada, Mandnl de la cuchdla 3 Parte(s) doblada el acette. o o suelta_ saelta(s)/da_ada(s). AJUSTAR en la seccion EL CARBURAde Servlclo y Ajustes. Pongase en eontacto con un centre servicio cualificado "SEARS". de 1 Cambie la c{_chdla la cuchilla. de 2 Cambte 3 Apriete la[s) da6adas. ex_esiva doblade. de a_re del motor. el silenciador. todo el alambrado. Vea "PARA desajustado 2 la el estanque de combustible y a Ilenarlo con gasohoa nueva, suctoitaponado. 1 [a velocid,_.d de la aceleraci6n. Vaciarelestanquedecombustib}eyelcarburadar, vuelva a Ilenarel estanque con gasolind nueva y cambie el filtro de combusbble. Conecte y apriete el alambre de I_ bujia. suelta de a=re del motor Vaciar vuelva el control Silenciador Carburador El motor con_Jnl_a funcionando cuando el Sears. CORRECC[ON (sigue) Vibraci6n a un centro de servicio Sistema de control que exige {a presencta del operador -seguddad fallado. la mandrd Apr_ete el perno de la cuchi]la. parte(s). Cambie las partes Revise et alambrado, los interruptores y la conexiones.Si no est&n correctas, Pongase en eontacto cod un centre de servicio cuahhcado "SEARS". operador se baja del asiento con el embrague de[ accesodo enganohado El corte disparejo Las cuchillas segadoras no rotan Cuchi[la desgastada, doblada o suelta. 1 Camb_e la cuchilla. Apriete el perno de la cuchilla. 2. El conjunte 2. 3 AcumuEaci6n de c6sped, hojas y basura debaio de la segadora. Mandnl de la cuchdla dab[ado. 3 Los aguleros de ventdaci6n del conjunto segador taponadosdebtdo a la acumulaci6n dec6-sped, hoias y basura alrededorde los mandriles. 5. Nivele el conjunto segador. Ltmpte la parte inferior de Ia cajade la segadora. Cambie la mandnl de la cuchdla. Dmpie alrededor de [as mandnles pard abnr los de venblac_6n. Obstruccf6n 4. segadoT no est&nive]ado. 4 1 Remueva La tarred de impuls_6n de la segadora est_ desgastada.ida6ada. 2 Cambte la eorrea segadora. Poled 3. Cambte Ia poled 4. Cambie la mandril Mandril enel mecan_smo de guia delembrague. atascada. de Ja cuchtBa atascada. 56 la obstrucc_Sn. de tmpu[si6n de guia. de la cuchdla. de la IDENTIFICACION Vea la secctbn DE PROBLEMAS: apropiada en el man ual a menos que est_ d irigido a un centro PROBLEMA CAUSA Mala descarga del c_sped 1 Velocidad 2 Velocidad de recorrido demastado r&ptda. C_sped roulade. 2 El conjunte sugarier no es_mvelada. Prest6n de airs de las Ilantas baja o dtspareja. Cuchil[a desgastada, doblada o sue]ta. 4. 5 7. g. Acumulact6n de c6sped, hojas y basura debafo de la segadora, La curfea de impulsi6n de [a segadora est& desgastada o desajustada. Las cuch_llas estb,n maF coninsta[adas. 10 Guchlllas l& 11 Los agujeros de veet=laci6n del conjunto agujeros segador taponados debido a la acumulaci6n de c_sped, hejas y basura alrededor de los maednles. I1. 1. "ENOIEND_:' 2 Gambie la bornbllla{s) 3 4. 5. 6, 7 8 Las ]uz (cos) de lantera(s) no funcio- de servicio Sears. CORRECCION del motor rnuy lenta. inadecuadas I. en use. est& =APAGADO"{OFF). 3. 6 8. 9 Ponga e] control de la aceleraci6n en la posici6n de "RAPtDO" [fast). Cambie a una velocidad mAs lenta. Permtta que se seque el c_spedantes de sugar. Nivele el conjunto segador. Revise las llanlas pare verificarque tienen la presibn de airs. Cambie/afile la cuchi[la. Apriete el pemo de la cuchilla. Ltmpte la parts inferior de la cajade la segadora. Oambie/ajuste la correa de impu}si6n de la segadora, ! Vuelva a insta_arlas cuchillas efborde afilado hacia abaJo. Oambie per las cuchJlJas enumeradas en este manual. Limpie alrededer de los mandriles para abrir los de ventilaci6n. 1. El interrupter 2. Bombilla(s) 3 Interrupter de la luz fallado. 3 Revise/cambie 4 Alambrado suelto 4 Revise el alambrado 5 Fusible 5. Camb=e el fusible. 1. 2 Elemente(s) de la bateria malo(s). Males conexiones de cables. _. ;z Gambie 3 4. Regulador Alterrtador a 4 Cambie el regulador. Cambie el alternador. 1 Residues es en de laplaca (Si equipado) e l_.mpara(e) quemada(s). ION) el interrupter. o I&rnpara[s), el interiuptor de la ]uz. lando La bateria no carga P_rdida de impulsi6n ; 2 3 El motor tien "contraexplosiones" cuando se "APAGA" El tractor se ponen marcha atr_s o da5ado. quemado. La correa quebrado. fallado (si equipado), falJado. de mov=m=ento Llave cuadrada de elees de direcciSn. es gaslado o ausente, y las conexJones. la bateria. Revise/JtmpJe todas las cables. 1 Vea "MMPIEZA" en la secci6n tenimento de este manual, 2. Reemplace la correa de movimien-to esta gastada, da_ada o rata. a. Vea "PARA REMOVER LAS RUEDAS" en ;a secci6n de Serviclo y Ajustes de este manual. El control de la aceleraci6n del motor no rue ajustado en la posici6n de velocldad media y m,_xima [r_plda) antes de pare el motor, Mueva El sistema de funcionamiento atr_.s (ROS) no es_ "ON', cuando enganche la segadora o otro accesorlo. Girar el ROS en la posici6n "ON".Vea la secci6n de operaci6e. 57 el control de Man- de [a aceleracl6rl ala }osici6n de velecldad media y m_ixima (r_pida) antes de pare el motor. GUfA SUGERIDAPARA MEDIRLAS PENDIENTESCON LA VISTA PARAUNA OPERACIONSEGURA 03 LO J H _IL n _1 ADVERTENCIA: Para evitar da_os graves, haga funcionar su tractor arriba Y abajo de las pendientes, nunca transversalments con respecto a las pendientes. No cortar pendlentes ntayores de t5 grados. Haga los vlrajes gradualmente para evitar vo[cafse o Is p_rdida de control Tenga mucho cuidado cuando c_mbie de dErecei6n on las pendJentes. 1. Plegar esta p,'_glna a Io largo de la Ifnea punteada arriba indicada. 2. Tenor |a pigina ante de sf mismos de modo que su horde izqulerdQ sea vertical paralelo a| tronco del :_rbol u otra estructura ve_lcaL 3, MIrar a trav_.s del pllegue en direcci6n de la pendiente que ae qulere medir. 4. Comparar el -'tnqulo deep|iogue con la pendlente del terre.qo. NEED HELP? MORE You'll fL_d ihe answ_; and i_ more o_ managemyhome.com - for free! _ • Findthis and eli your other product manualsonline • Getanswersfrom our team of home experts. _. • Geta personalized mmntenanceplan for your home. "_ • Findinformation and LooL_ to help wlth home pfo_ects manage _ home brought to y_u _y Sear_ •" " Your ' "::':" Home For repair - in your home - of all maior brand apphances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it[ ?. ::: For the replacement parts, accessories and owner's manuals that you need to de-it-yourself. -) _'. For Sears professional installation of home appliances and items like garage door openers and water heaters, " 1-800-4-MY-HOME ® (I-800-4S9-4563) www.sears,com Anyhrne,dayor night {U.S.A, and Canada) www,aears.ca 5 i Our Home _)'.2" For repair of carry-m products )ike vacuums, iawn equipment and electronics, call or go on-line for the nearest Sears Parts and Repair Center. 1-8D0-488-1222 ? .- -L I -.:Z Anybmo, dayor night (U,S A, only) www.sears.com To purchase a protectton agreement (U.S A ) or maintenance agreement (Canada) on a product serviced by Sears: 1-800-827-6655 (U.SA_ t-800-361-6665 (Ce_a_) 5- Para pedir se_c_o de reparaddn a domhlho, y para ordenar piezas, 1-888-SU-HOGAR _ (1-888-784-642_ i. :: Sears Registered "rradell_ @ Marca Regl_lrada I0.04.1I AP Au Canada pour service en fmn_Ls: 1.800.LE.FOYER ac {_-m_533-6_37) v_tw.sears,ca • I "r_ T.'_dema 1 ';_' M_rca rk J s_ _er_Ge Mgrk Of S_r_ de F_bnca / _" Marco d_ Se_l_ _r_rtd_, de Seers LLC: Srands, LLC , -.:. =:" - --:
This document in other languages
- español: Craftsman 917.25022