Download Security Link SL150 Installation manual
Transcript
® ® US L I STED Pending UL325 compliant WWW.ALLOMATIC.NET UL991 compliant SL-100DC & SL-150DC Installation Manual Copyright © 2008 all-o-matic inc. www.allomatic.net TABLE OF CONTENTS Important safety instructions............................................................. 2 Different UL 325 class types........................................................ 3&4 Concrete pad installation............................................................. 5&6 Different installation types (front & rear mounts).............................. 7 Gate travel adjustment................................................................. 8&9 Directional settings..........................................................................10 Electrical power connection.............................................................11 Typical loop layout.................................................................... 12&13 Accessory connections................................................................... 14 Multiple safety device connection................................................... 15 Plugin loop detector installation...................................................... 16 Leading edge installation................................................................ 17 Three button station system installation..........................................18 Master/Slave connection.................................................................19 Magnetic/Solenoid lock installation................................................. 20 Radio receiver hookup.................................................................... 21 Open and close electronic reversing sensor(ERDs) adjustment.... 22 Timer adjustment............................................................................ 23 Dip switch functions........................................................................ 24 Solar panel installation................................................................... 25 Led diagnostics.............................................................................. 26 Emergency release......................................................................... 27 1 IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of injury: READ THE FOLLOWING DIRECTIONS. DO NOT EVEN THINK OF STARTING UNTIL YOU HAVE READ AND UNDERSTAND THESE DIRECTIONS. IF THERE IS SOMETHING YOU DO NOT UNDERSTAND CALL US. Never let children operate or play with gate controls. Keep the remote control away from children. Always keep people and objects away from the gate. No one should cross the path of the moving gate. This operator must be tested monthly. The gate must reverse on contact with a ridged object or stop when an object activates the non-contact sensors. After adjusting the force or the limit travel, retest the gate operator. Failure to adjust and retest the gate operator properly can increase the risk of injury. Keep gates properly maintained. Have a qualified service person make repairs to gate hardware. It takes many years of experience to make proper adjustments to gate hardware or operators. There is nothing on a gate operator that is easily repaired without a great deal of experience. Save yourself some time and call a qualified Gate Service Contractor who knows your type of gate operator. 2 INSTALL THE GATE OPERATOR ONLY WHEN YOU HAVE READ THE FOLLOWING: *Confirm that the gate operator being installed is appropriate for the application. *Confirm that the gate is designed and built according to current published industry standards. *Confirm that all appropriate safety features and safety accessory devices are being incorporated, including both primary and secondary entrapment protection devices. *Make sure that the gate works freely before installing the operator. *Repair or service worn or damaged gate hardware before installation of the operator. *Eliminate all gaps in a sliding gate below a 4 foot height that permits a 2 ¼ inch sphere to pass through any location, including the area of the adjacent fence covered when the gate is in the open position. *Eliminate all gaps in a swinging gate below a 4 foot height that permit a 4 inch sphere to pass through any location, including the hinge area of the gate. *Operator must be disconnected from the power source before attempting any installation of accessories. *Install this gate operator according to our installation instructions. *Adjust the operator clutch or load sensing device to the minimum force setting that will still allow for reliable gate operation. *Install the operator inside the fence line(do not install the operator on the public side of fence line). *Install a proper electrical ground to a gate operator. *Install controls where users cannot touch or reach through the gate to operate the controls. *Install all warning signs and take pictures of the installation. *Test all safety features for proper function before placing the automatic vehicular gate into service. *Train owner/users about basic functions and safety features of the gate system, including how to turn off the power and how to operate the manual disconnect feature. *Leave safety instructions, product literature, installation manual and maintenance manual with end user. *Explain to the owner/user the importance of routine service and retesting on a monthly basis. 3 DIFFERENT UL 325 CLASS TYPES Class one: Residential A vehicle gate operator intended for use at a home of one to four single family dwellings, garages or parking area. Class Two: Commercial or General Public Access A vehicular gate operator intended for use at a commercial location or building such as a multi-family housing unit (five or more single family units), hotel, garages, retail stores, other buildings servicing the general public. Class three: Industrial or limited Access A vehicular gate operator intended for use at an industrial location or building such as a factory, loading dock area, or other locations not intended to service the general public. Class Four: Restricted Access A vehicular gate operator intended for use at a guarded industrial location or building such as airport security areas or other restricted access locations not servicing the general public where unauthorized access is prevented via supervision by security personnel. Other components required to satisfy UL 325 Each class must have a primary and secondary means to sense and react to obstructions within two seconds. The six types of obstruction sensing systems are : Type A: Inherent obstruction sensing system. This system must sense and initiate the reverse of the gate within two seconds of contact with a solid object. Type B 1: Provision for connection of a non-contact device can be used, such as a secondary protection. Type B2: Provision for connection of a contact sensor. Examples include an edge device or equivalent. This can be used for secondary protection. Type C: Inherent adjustable clutch or pressure relief valve. Type D: Provision for connection of or provided with and actuation device requiring continuous pressure. Type E: Inherent audio alarm. All of All-O-Matic Inc’s Gate operators conform to the most ridged Class One. 4 CONCRETE PAD PLACEMENT FOR SL-100DC GATE TRACK FOOTING GATE TRACK GATE 10” Minimum 5” RED HEAD BOLTS FOUR PLACES ½”X 3 ½” Operator plastic cover 17” 10” 24” Area for conduit(s) Operator frame Operator concrete pad 9½” 12 1/4 ’’ 24” Drive chain level for rear mount When possible Install 4” above Ground Drive chain level for front mount 23 23½” ½” 6.5” GATE TRACK FOOTING 4” 4” 8” 24” Footing for Gate operator 5 CONCRETE PAD PLACEMENT FOR SL-150DC GATE TRACK FOOTING GATE TRACK GATE 10” Minimum 5” FOUR RED HEAD BOLTS ½”X 3 ½” 15” 7.5” 24” Area for conduit(s) 16.25” 20” 30” Drive chain level for Rear mount 25” Drive chain level Gate track Footing When possible Install 4” above ground level 6” 2½” 2½” 4” 8” 24” Footing for gate operator 6 DIFFERENT INSTALL CONFIGURATIONS Gate in open position A front mount installation and chain layout Gate closed Operator footing Track footing Gate operator Overhead View DRIVEWAY Track footing Operator footing Gate in open position Gate operator Operator footing Rear mount installation and chain layout Gate closed Track footing See blow out below DRIVEWAY Operator footing Move one idler to bottom center hole and follow chain path as shown. Gate operator footing Chain path Track footing Safety guard Gate Front idler Gate post 7 GATE TRAVEL ADJUSTMENT FOR SL-100DC Locate limit switches Step 1: Stop the gate operator using the three button station on the board. Step 2: Push limit lock plate down. Turn limit nut in the desired direction. Step 3: Place limit plate to its locked position. Step 4: Run gate operator. Step 5: If more adjusting is needed, repeat steps 1-4. Limit nuts Gear box Each notch equals about ½” of travel. Limit nut lock plate 8 GATE TRAVEL ADJUSTMENT FOR SL-150DC Locate limit switch box. Step 1: Make sure operator is not running . Step 2: Use a screw driver to pull limit lock plate outwards. Turn Limit nut to desired direction. Step 3: Place limit plate to its locked position. Step 4: Run the operator. Step 5: If more adjustment is needed, repeat the steps (2-3) until desired position is acquired. Limit switch Each notch equals about ½” of gate travel. Limit nuts Limit nut lock plate Limit plate must be tight in limit nut slots for gate to hold it’s limits. 9 OPENING DIRECTION SETTINGS Use OPEN L/R dipswitch to change the opening direction on the operator. OFF for left hand opening, ON for right hand opening. .01 I / 5W I0615 O O 20M 1001 1001 6040 1212 2402 3002 MAAF S21B C8RB LMC64 82AIM 33 HFK 5GN F260 1001 UC3906DW U 74ZF2CW 602 SS26 602 SS26 1212 DR127-330 43CL07 E 1131 9531 ON 802 B 360G 4750 602 SS26 829B R 16 6 802 B 360G NO SS 14 911C0 107A 10 0 HFK. 7J2 2491 C8RB LMC64 82AIM 104 Coilcraft F C8RB LMC64 82AIM 476E 476E 900R3 900R3 2491 2262 72CB74K G4 Ls14 IOR IR2110S 0618 90R9 683 Coilcraft V 710 KE . 1001 4021 1001 80 2 B 3 60 G ON 10R0 1000 2001 829B R616 2001 9 145 1AM 710 KE. 4750 72CB74K G4 Ls14 1001 1001 BO U BO U 1001 1001 1001 BO U 829B R616 4750 1002 1002 1002 1501 710 KE. 1001 1501 3 ATMEL ATMEGA168 20AU 0743 2001 C8RB LMC64 82AIM 58ADC1K G4 Ls07 1501 1002 PHILIPS 1501 1501 1002 72CB74K G4 Ls14 1002 1001 829B R616 SS 14 1001 710 KE. 1001 710 KE. 1002 1002 1002 1002 CMX-309FB C 8.0000 M 5 35 2 0 2 72CB74K G4 Ls14 1001 710 KE. 1000 1002 1501 710 KE. SS 14 RNS 1 710 KE. 3 710 KE. 1 8 33 6 RNS 8 33 6 3 PHILIPS 1501 1002 1501 MOC8050 629Q 1 2 1002 3 3 C8RB LMC64 82AIM 4 5 1001 1001 710 KE. 8 1 21 0 7 710 KE. 6 -----------------------OPEN------------------------ 2 1 RS 0022 9 1001 W107DIP - 3 1000 A1 M IOR F MAGNECRAFT 10R0 710 KE. 58ADC1K G4 Ls07 IR2110S 90R9 0618 1 2 1002 C8RB LMC64 82AIM 3 4 5 710 KE. 1001 8 1001 7 1210 6 Opening 1 10R0 -----------------------OPEN------------------------ RIGHT HAND RNS 8 33 6 IOR IR2110S 0618 90R9 LED’s will show opening or closing directions when gate is running. 1501 1002 1332 1001 LEFT HAND Opening Right hand and left hand opening is from behind the operator. 10 ELECTRICAL CONNECTION OPERATORS MUST BE PROPERLY GROUNDED! 230V Power switch 115V NOTE: When applying 230V to operator make sure voltage switch is flipped to 230V position. GRD LINE 1 LINE 2 120 Volt Electrical Plug. Power connection LINE 1 = LINE 2 = | 115VAC | 220VAC Single Phase 115V HOT 220V LINE 1 115V N 220V LINE 2 GND Connect to ground. Use a proper ground rod for a ground reference. Use the shortest and thickest wire possible for ground. For power, a minimum of a 20-Amp dedicated circuit breaker is needed. For power wire enclosure use UL listed conduits. NOTE: To use the 120VAC accessory outlet, connect white wire from the outlet to neutral. Only when using 120VAC as the power source. All gate operators MUST be properly grounded. A proper ground in a gate operator installation minimizes or prevents damage from an electrical charge, such as a near lightning strike or an electrical static discharge. . Use a single wire for the ground. DO NOT splice two wires for the ground. If the wire breaks or is cut, replace it with a single length. NEVER use two wires for the ground. Check with your City code for proper earth ground rod type and proper grounding procedures. 11 TYPICAL LOOP LAYOUT 8 FT SAFETY LOOP GATE TRACK TWISTED 6 TURNS PER FOOT 1 1/2 IN 4 FT SAFETY LOOP EXIT LOOP 4 FT GATE OPERATOR 1/4 IN 8 FT GATE 4 FT 4 FT WIRED IN SERIES 4 FT OUT WHEN USED This is a normal loop layout. Remember when connecting to an All-O-Matic circuit board you use the normally closed contacts for your safety loop detector and normally open contacts from the exit loop. You must twist your wires from your exit point of the saw cut all the way to the circuit board, no exceptions. 12 GENERAL LOOP INSTALLATION GUIDELINES The following loop installation guidelines are for installing typical driveway loops for access control applications (i.e. parking gates, sliding gates, swing gates etc...) Always consult withl loop detector manufacturers for specific equipment guidelines. This will confirm that the proper configuration and installation techniques are properly applied for your application. Useful information about inductive loops: A. The typical sensing height is 2/3 of the shortest leg of loop (in feet) Therefore a 4’ x 8’ loop typically has a detection height of 2.6’. B. The inductance of a conventional four-slide loop can be estimated using the formula: L = P x (T2 + T) / 4 Where L = Loop Inductance in microHenries P = Loop Perimeter in feet T = Number of turns of wire in saw slot Therefore a 4’ x 8’ loop with 3 turns would be: TWISTED 6 TURNS PER FOOT L=(4 + 8 + 4 + 8) x (32 + 3) / 4 L=24 x (9 + 3) / 4 L=24 x 12 / 4 L=24 x 3 L=72 microHenries 1/4’’ Feeder Slot Driveway loop Suggested guidelines for loop installation: Loop wires should be twisted 6 turns per foot, and twisted from saw slot to the detector. If possible start twisting the wires from the edge of the loop. All 90 degree corners should be chamfered so that the course of the wire does not change direction sharply but rather at shallower angles of 45 degrees or less. Core drilling of the corners achieves the same effect but can still lead to failure due to sharp edges remaining in the corner area. 45 Angles Driveway Saw Slot 1/4’’ Loop # of Perimeter Turns 6’ - 12’ 6 13’ - 20’ 5 21’ - 60’ 4 61’ - 240’’ 3 241 & Up 2 Sealant: 3/4’’ to 1’’ Min. 2’’ Backer Rod } Loop Wire: 3 Turns 13 ACCESSORY CONNECTIONS The circuit board 12-VDC output provides up to 500 mAmps of power for accessories. More than two or three accessories will require a separate power supply. NOTE: 12VDC Accessories only. 1002 710 KE. 710 KE. 7 10 KE. 7 10 KE. 1002 1002 1002 1002 2402 1001 ON 1001 1001 6040 1501 1501 1501 1501 1501 1501 1501 1501 1 50 1 MAAF S21B 1002 7 10 KE. 710 KE. 7 10 KE. 710 KE. 1002 C8RB LMC64 82AIM 1002 802 B 360G 7 10 KE. 683 Coilcraft V 1002 20M 2 33 HFK 5GN 1212 3002 DR127-330 43CL07 E 3 1 RS See page 16 for plugin loop detector installation. C Remove wire jumper from SAFETY when a safety device is installed. C Power Detect 2 3 4 PRES 5 2 6 FREQ. 1 0 0 Loop Fail 2 0 1 2 0 3 OFF 4 PRES 5 2 6 SENS. LEVEL 1 BOOST ON PULSE FREQ. 0 0 1 GHI 4 0 SAFETY Loop Detector Reset N/C ABC 2 JKL 3 6 TUV 7 WXYZ 8 9 TONE OPER 0 AB DEF MNO 5 PQRS * Card Reader or Key Switch 0 OFF PULSE Reset Push Button or Fire Box 1 BOOST ON Loop Fail Keypad or Telephone 2 1 SENS. LEVEL Power Detect 1 EXIT Loop Detector PHOTO Beam # N/O See page 12 for connection of multiple safety device wiring diagram. C = COMMON N/O = NORMALLY OPEN CONTACT N/C = NORMALLY CLOSED CONTACT 14 MULTIPLE SAFETY DEVICES CONNECTIONS Multiple SAFETY devices installed together must be connected “in series”. Locate the normally closed (N.C.) dry contact from each accessory relay. Before installing the accessory devices, remove the wire jumper from the SAFETY position on the control board. Safety wire connections From Accessory #1 To Connecting pin From Accessory #2 To Connecting pin Relay Com Relay N.C. To COMMON To SAFETY From Accessory #1 to Accessory # 2 Relay N.C. To Relay COM 1002 1002 2402 1001 ON 1001 1001 6040 1501 1501 1 5 01 1501 1501 1501 1501 1501 1501 MAAF S 21 B 1002 710 KE. 1002 7 10 KE . 710 KE. 710 KE. 7 10 KE. 1002 710 KE. 7 10 KE. 710 KE. 1002 C8RB LMC64 82AIM 1002 802 B 360G 710 KE. 683 Coilcraft V 1002 1002 20M 2 PHOTO Beam Relay (N.C.) SAFETY Loop detector AB Reset Loop Fail 6 2 5 PRES 4 1 0 0 PULSE 3 Remove wire jumper from SAFETY when a safety device is installed. BOOST ON FREQ. SENS. LEVEL 2 33 HFK 5GN 1 RS Relay (COM) 1 1 1212 3002 DR127-330 43CL07 E 3 2 OFF 0 0 Detect Power Relay (N.C.) Relay (COM) Wire nut This diagram is for the relay wires of the safety devices, two wires to the board connections (one from each device) and two wires to the orange wire nut. 15 ® LPR-1 LOOP RACK INATALLATION This is a typical loop configuration for a gated driveway. Remember when connecting to an All-O-Matic circuit board the safety (reverse) uses normally closed contacts from the loop detector, the wire jumper from the safety connector needs to be removed when a safety loop is inatalled. You must twist your wires from your exit point of the saw cut all the way to the loop detectors, no exceptions. E Exit xit loop Exit Loop Phantom Loop Ground Exit Loop Connections 24VAC/ 12VDC WHEN USED Exit Loop Inside Safety loop Only for swing gates Phantom Loop Phantom Safety Safety Loop See side for Jumper setting Safety Loop Outside Safety loop NOTE: To wire one or multiple safety devices in use with loop rack safety device remove loop rack safety white contact wire (N.C.) From safety pin connector on circuit board and wire in Series with added safety devices using the (N.C.) Contact wire from your safety device in the safety contact. DR127-330 43CL07 E 1 RS 1501 1501 1501 1501 1501 1501 1501 1002 1002 1 00 2 1 00 2 1002 1002 1002 1002 1001 1001 2402 C8RB LMC64 82AIM 1501 1501 3002 ON 1002 1212 2 1001 MAAF S21B 6040 3 33 HFK 5GN 802 B 360G Compatible Detectors Brand Reno A&E EDI Diablo Controls Model No. H2 LMA-1500-LP DSP-40S Jumper setting OFF OFF ON 16 LEADING EDGE CONNECTION 1002 1002 1002 710 KE. 710 KE. 7 10 KE. 7 10 KE. 1002 1002 2402 1001 ON 1001 1001 6040 1501 1501 15 01 1501 1501 1 50 1 1501 1501 1501 MAAF S21B 1002 7 10 KE. 710 KE. 7 10 KE. 710 KE. 1002 C8RB LMC64 82AIM 1002 802 B 360G 7 10 KE. 683 Coilcraft V 1002 20M 2 33 HFK 5GN 1212 3002 DR127-330 43CL07 E 3 1 RS RED wire to 12VDC BLACK wire to COMMON LEADING EDGE SENSOR Wireless edge Receiver Connect one of the wires from leading edge and/or one of the grey wires from a wireless edge receiver to COMMON connector on control board. Connect the other wire from leading edge and/or the other wire from a wireless edge receiver to EDGE connector on control board. 17 THREE BUTTON STATION SYSTEM See push button connections below. C8RB LMC64 RNS O B U 1002 1001 1001 1 PHILIPS O B U RNS ON 802 B 360G 8 33 6 3 1001 1001 2262 RNS 2491 O B U C8RB LMC64 82AIM 1 8 33 6 3 100 HFK. 7J2 476E 900R3 911C0 476E 1AM 9 107A W107DIP - 3 MAGNECRAFT PHILIPS 104 Coilcraft F 3 71 0 KE. 8 33 6 71 0 KE. 1 1210 900R3 1001 0022 2491 C8RB LMC64 82AIM 802 B 360G 72CB74K G4 Ls14 58ADC1K G4 Ls07 72CB74K G4 Ls14 58ADC1K G4 Ls07 ON F MOC8050 629Q 4021 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 683 Coilcraft V 1501 1501 1501 1501 1501 1501 2 1501 1501 3 1002 1002 1002 1002 1002 1002 1002 1002 1002 1501 A three button station was integrated on the board to make adjustments easier when setting limit switches and adjusting ERDs. 1 RS PED-SW Jumper Connect the COMMON from all the push buttons to COMMON input on the board. Connect OPEN push button N.O. contact to EXIT input on the board. N.O. Connect CLOSE push button N.O. contact to 3BT input on the board. N.O. Connect STOP push button N.C. Contact to PED-SW input on the board and remove PED-SW jumper. N.C. OPEN CLOSE STOP COM 18 MASTER/SLAVE CONNECTION Before connecting master/slave gate operators together, test and adjust the limit switches and the ERDs for each operator as “stand alone” machines. All accessories must be installed on the master board, no exception. See page 22 for dip switch settings. Use a two wire shielded cable and run it through a UL listed conduit for master/slave connection. Follow the wiring diagram as shown below. Master Board Slave Board +.....................Positive to Positive...................+ -...................Negative to Negative...................- 2 3 4 5 6 7 8 Slave switch ON only on slave board Slave Board 1 Master Board Shielded cable -----------------------OPEN------------------------ Use UL listed conduit 1001 C8RB LMC64 82AIM 10 01 1210 1002 7 10 KE. -----------------------OPEN------------------------ 7 10 KE. 1 2 3 4 5 6 7 8 1 00 1 C8RB LMC64 82AIM 1001 1210 7 10 KE. 1002 7 10 KE. Connect shield to slave metal frame only. 19 MAGNETIC/SOLENOID LOCK CONNECTIONS Magnetic lock installation requires a step down transformer with appropriate voltage for the specific lock accessory. Operator will provide a 120VAC outlet for the step down transformer. Connections: Plug the lock device transformer to the 120VAC outlet plug. For Magnetic lock: Connect one wire from transformer directly to one wire of the magnetic lock, the other wire from transformer will be connected to the relay plug COM input and the MAG relay output connects to the other wire of the magnetic lock. See illustration below. 1 3 1 3 1501 1002 3 1001 1 1001 4750 1001 IOR 710 KE. 1501 1002 ATMEL ATMEGA168 20AU 0743 2001 C8RB LMC64 82AIM 9 0R 9 58ADC1K G4 Ls07 710 KE. SS 14 For Solenoid lock: Connect one wire from transformer directly to one wire of the solenoid lock, connect the other wire from transformer to the relay plug COM input and the SOL relay output connects to the other wire of the solenoid lock. See illustration below. PHILIPS 710 KE. PHILIPS 1501 72CB74K G4 Ls14 1001 1002 1001 1002 1001 1002 1001 1002 CMX-309FB C 8.0000 M 535202 710 KE. 72CB74K G4 Ls14 1002 1501 10R0 1000 829B R616 710 KE. SS 14 1002 1501 710 KE. F 10R0 9 0022 1AM W107DIP - 3 1001 MAGNECRAFT MOC8050 629Q 1 2 1002 C8RB LMC64 82AIM 3 4 5 710 KE. 710 KE. 1001 8 1001 7 1210 6 -----------------------OPEN------------------------ 1000 1002 1501 710 KE. IOR IR2110S 0618 58ADC1K G4 Ls07 1002 1501 90R9 Relay plug SOLENOID LOCK 120VAC outlet plug MAGNETIC LOCK Step Down Transformer 20 RADIO RECEIVER CONNECTIONS 3 wire receiver: mounts on receiver strip outside control box as shown below. 4 wire receiver: connect the two relay wires to 1 & 2 terminals. Black negative wire to terminal 1 and Red positive wire to terminal 3 on receiver strip outside control box as shown below. 1AM 9 1001 0618 R IOR IO 0618 829B R616 145 17 0 KE. IOR IR2110S IR2110S 710 KE. 829B R616 829B R616 IOR IR2110S 2001 4750 2001 1AM C8RB LMC64 82AIM -----------------------OPEN------------------------ 9 .01 I / 5W I0615 4750 O O 2001 1 2 3 1001 1001 C8RB LMC64 82AIM RNS O B U 1001 1 1001 F260 602 SS26 602 SS26 RNS O B U 602 SS26 ON 802 B 360G 3 8 33 6 1001 1001 2262 C8RB LMC64 82AIM 1 O B U 2491 RNS 8 33 6 3 100 HFK. 7J2 476E 900R3 UC3906DW U 74ZF2CW 6 7 8 911C0 9 107A 5 PHILIP PHILIPS S W107DIP - 3 MAGNECRAFT PHILIPS 104 Coilcraft F 3 710 KE. 8 33 6 4 1 1002 71 0 KE. 0618 1332 1001 1001 1001 72CB74K G4 Ls14 CMX-309FB C 8.0000 M 535202 1501 1001 1210 10R0 1001 1001 ATMEL ATMEGA168 20AU 0743 72CB74K G4 Ls14 1002 1001 1002 1002 1002 SS 14 90R9 1000 SS 14 1001 90R9 10R0 1001 1000 SS 14 90R9 10R0 1000 F MOC8050 629Q 829B R616 0022 476E 1AM 900R3 1001 1212 4750 1131 9531 0022 2491 802 B 360G C8RB LMC64 82AIM 72CB74K G4 Ls14 58ADC1K G4 Ls07 72CB74K G4 Ls14 ON F MOC8050 629Q 58ADC1K G4 Ls07 4021 C8RB LMC64 82AIM 1001 NO 1001 1001 6040 1501 1501 1501 1501 3 2 1 3 = 12V 2 = Relay 1 = Common 33 HFK 5GN 1212 3002 DR127-330 43CL07 E Receiver terminal strip located outside control box. 1501 3 wire 12VDC Radio Receiver 3 wire 12VDC Radio Receiver 1501 RS 1501 1 1501 2 1501 3 2402 MAAF S21B 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 710 KE. 20M 8 20 B 360G 710 KE. 683 Coilcraft V 1002 1002 1002 1002 1002 1002 1002 1002 1002 4 wire 12VDC Radio Receiver 21 OPEN AND CLOSE ELECTRONIC REVERSING SENSOR(ERDs) ADJUSTMENT Open and Close ERD SENSITIVITY .01 I / 5W I0615 O O 1001 6040 20M 2402 33 HFK 5GN 1001 1212 3002 MAAF S21B C8RB LMC64 82AIM 1212 1001 F260 DR127-330 43CL07 E UC3906DW U 74ZF2CW 6 02 SS26 602 SS26 1131 9531 ON 802 B 360G 4750 602 SS26 MAX 1001 8 92 B R6 61 NO 476E 2491 900R3 2262 476E C8RB LMC64 82AIM 900R3 72CB74K G4 Ls14 MIN 683 Coilcraft V 2491 C8RB LMC64 82AIM 104 Coilcraft F MIN MAX 4021 802 B 360G SS 14 911C0 100 HFK. 7J2 107A 710 KE. IOR IR2110S 0618 90R9 1001 802 B 360G ON 10R0 1000 2001 829B R6 61 2001 1501 710 KE. 1501 1002 710 KE. 710 KE. 1002 1001 1002 1001 1002 1001 1002 1501 72CB74K G4 Ls14 1001 1 3 1001 1001 710 KE. PHILIPS CMX-309FB C 8.0000 M 535202 72CB74K G4 Ls14 1000 1002 1501 10R0 1 00 1 ATMEL ATMEGA168 20AU 0743 2001 C8RB LMC64 82AIM 58ADC1K G4 Ls07 PHILIPS N R S BO U 1002 1501 BO U 3 1 00 1 1501 1002 BO U 1001 1001 BO U 1001 1001 1001 4750 BO U 829B R616 1001 1 710 KE. 3 8 33 6 1 8 33 6 3 N S R 8 33 6 1 N S R 8 33 6 N S R 8 33 6 IOR IR2110S 0618 SS 14 1002 145 4750 72CB74K G4 Ls14 90R9 N R S 9 1AM 710 KE. 1332 1001 1 3 8 92 B R6 61 710 KE. SS 14 1002 1501 710 KE. 58ADC1K G4 Ls07 F 10R0 1AM 9 0022 1001 MAGNECRAFT W107DIP - 3 1002 1501 710 KE. IOR IR2110S 0618 90R9 1002 1501 MOC8050 629Q 1000 1 2 3 C8RB LMC64 82AIM 4 5 710 KE. 1001 1001 8 710 KE. 7 1210 6 -----------------------OPEN------------------------ 1002 ERD’S must be adjusted by qualified technician. The gate operator ERDs must be adjusted so that the gate provides regular, reliable and safe cycles. Counter clockwise maximum sensitivity Clockwise minimum sensitivity When gate stops and reverses by itself, ERD must be checked every six the ERD is too sensitive. months. The gate must stop and reverse when it hits an obstruction or the ERD is not sensitive enough. 22 TIMER ADJUSTMENT TIMER ON: Timer to close, can be set from 1 to 60 seconds. TIMER OFF: Gate operation is push button to open, push button to close. TO OVERRIDE THE TIMER: Turn the RADIO switch to the “ON” position. This will allow the radio receiver to close the gate before the timer. TIMER ADJUSTMENT Turn potentiometer counter clockwise for more time. 0 60 Sec Sec Turn potentiometer clockwise for less time. 0 60 Sec Sec .01 I / 5W I0615 O O 1001 6040 2402 20M 1001 1212 MAAF S21B 01 01 1212 602 SS26 1131 UC3906DW U 74ZF2CW 602 SS26 3002 33 HFK 5GN C8RB LMC64 82AIM F260 DR127-330 43CL07 E 9531 4750 ON 802 B 360G 602 SS26 829B R616 ON 476E 2491 476E 2262 72CB74K G4 Ls14 C8RB LMC64 82AIM 900R3 SS 14 683 Coilcraft V 2491 C8RB LMC64 82AIM 104 Coilcraft F 900R3 1001 4021 802 B 360G 710 KE. IOR BO U 911C0 107A 100 HFK. 7J2 1001 IR2110S 90R9 0618 8 33 6 1001 1001 N R S 802 B 360G ON 10R0 1001 2001 2001 1501 47 05 72CB74K G4 Ls14 1501 3 1501 ATMEL ATMEGA168 20AU 0743 20 10 90R9 1002 1 1002 BO U 1001 1001 BO U 1001 1001 1001 4750 BO U 829B 6R 16 1001 3 710 KE. SS 14 1 710 KE. 3 N R S 8 33 6 8 33 6 IOR IR2110S 0618 1 N R S 8 33 6 N R S 1002 9 1AM 1001 58ADC1K G4 Ls07 1501 C8RB LMC64 82AIM 1002 1001 1332 145 3 829B R616 1 710 EK . 4750 1000 710 KE. PHILIPS 1501 710 EK . 1002 1001 1002 1001 1002 1001 S PHILIPS PHILIP 1501 72CB74K G4 Ls14 1002 CMX-309FB C 8.0000 M 535202 1001 710 KE. 72CB74K G4 Ls14 1002 10R0 1000 829B R616 1002 SS 14 710 KE. 710 EK . 1002 1501 1501 58ADC1K G4 Ls07 1002 1501 710 KE. IOR IR2110S 0618 TIMER “ON” to activate the timer 90R9 F 10R0 0022 1AM 9 W107DIP - 3 1001 MAGNECRAFT MOC8050 629Q 1000 1 2 3 C8RB LMC64 82AIM 4 5 710 KE. 1001 1001 8 710 KE. 7 1210 6 -----------------------OPEN------------------------ 2 3 4 5 6 7 8 OFF 1 RADIO “ON” = Allows the transmitter to close the gate before the timer. -----------------------OPEN------------------------ TIMER RADIO OSC FAIL SF/SC 1-PASS SLAVE AUTO OPEN OPEN L/R 1002 ON 23 DIP SWITCH FUNCTIONS OFF 1 TIMER switch “ON” activates the TIMER. See page 21 for details 2 . 3 4 RADIO RADIO switch “ON” allows the radio receiver to override the timer. See page 21 for details. 5 OSC 6 7 8 -----------------------OPEN------------------------ TIMER RADIO OSC FAIL SF/SC 1-PASS SLAVE AUTO OPEN OPEN L/R TIMER ON OSC switch “ON” allows the radio receiver to stop and reverse the gate in any direction. During a cycle the first signal stops gate, a second signal reverses gate. FAIL SF/SC This is to set the operator as fail-safe or fail secure. ON for Fail-safe: on power failure, board will monitor battery voltage to make sure gate opens before battery drains out completely. OFF for Fail-secure: on power failure gate will run until battery is low and stay close. 1-PASS This is a true one pass, anti-tailgating feature. This feature may only be used with safety loops. With this switch in the “ON” position, the gate will open until one car passes the safety loops then it will stop and close. If a second car pulls on the loop the gate will stop the car must then back off the loop before the gate will close. SLAVE This feature is used on master/slave setups. Set slave switch “ON” on slave machine, all other switches “OFF”. Set slave switch to the “OFF” position on master machine. Set other function switches on master machine as desired. See page 17 for more details on master/slave connections and settings. AUTO OPEN This feature is to automatic open the gate on power interruption. It is a very particular feature used in areas where the fire department requires the gate to open automatically after a power outage. Set this dip switch “ON” when this feature is desire. OPEN L/R This feature is to set the direction the operator will open. See page 8 for details. 24 SOLAR PANEL CONNECTION The solar panel input will take a 12VDC panel or two 12VDC panels wired in sires to make 24VDC . The charging circuit is limited by 1 Amp max. NOTE: For information on what solar panel to use on any other type of installation call ALL O MATIC for Assistance. 802 B 360G ON 20M 1001 1001 1001 3002 2402 6040 DR127-330 43CL07 E MAAF S21B 1212 C8RB LMC64 82AIM .01 I / 5W I0615 O O 802 B 360G ON 20M C8RB LMC64 82AIM F260 1212 DR127-330 43CL07 E 1001 1001 6040 4750 2402 602 SS26 3002 MAAF S21B UC3906DW U 74ZF2CW 602 SS26 1001 1212 1131 9531 602 SS26 1001 4021 802 B 360G 829B 6R 16 ON 476E 476E 900R3 C8RB LMC64 82AIM 2491 900R3 IOR IR2110S 72CB74K G4 Ls14 683 Coilcraft V 2491 C8RB LMC64 82AIM 104 Coilcraft F 2262 SS 14 911C0 100 HFK. 7J2 107A 710 KE. 1001 0618 90R9 802 B 360G ON 10R0 1000 2001 829B R616 2001 1501 145 4750 72CB74K G4 Ls14 1501 1002 BO U 1001 1 3 1501 1002 3 1001 BO U 1001 1001 1001 4750 BO U 829B R616 1001 1 710 KE. 3 N R S 8 33 6 1 N R S 8 33 6 N R S 8 33 6 710 EK . 58ADC1K G4 Ls07 C8RB LMC64 82AIM 90R9 1501 1002 ATMEL ATMEGA168 20AU 0743 20 10 IOR IR2110S 0618 710 KE. SS 14 1002 9 1AM 710 KE. 1332 1001 PHILIPS 710 KE. PHILIPS PHILIPS 1501 72CB74K G4 Ls14 710 EK . 1001 1002 1001 1002 1001 1002 1001 1002 CMX-309FB C 8.0000 M 535202 72CB74K G4 Ls14 1000 1002 1501 10R0 8 92 B R616 1002 SS 14 710 KE. 710 KE. 1002 1501 1501 F 10R0 0022 1AM 9 1001 MAGNECRAFT W107DIP - 3 1002 1501 710 KE. IOR IR2110S 0618 90R9 58ADC1K G4 Ls07 MOC8050 629Q 1000 1 2 3 C8RB LMC64 82AIM 4 5 710 KE. 1001 1001 8 710 KE. 7 1210 6 -----------------------OPEN------------------------ 1002 25 LED DIAGNOSTICS AC/PWR ON: Will be lit when AC power is ON. M/S LINK: Will be lit when master/slave communication is active. ALARM: Two states. 1st state: LED will blink(horn will beep also) every 30 seconds when battery is low, bad or disconnected. 2nd state: LED will turn on for 5 minutes when operator goes on shut down mode do to the gate hitting an obstruction(E.R.D.). Also, the horn will go off for 5 minutes. LOW BATTERY: Three states. 1st state: LED will be on solid when battery is low. 2nd state: LED will blink slow(about every 2 seconds) when an overload occurs(over current). 3rd state: Will blink fast(abouty every ½ second) when gate is jammed or motor sensors Are not responding or disconnected. OPEN-LIMIT: LED will be on while limit nut is against open limit switch. CLOSE-LIMIT: LED will be on while limit nut is against close limit switch. OPENING: LED will be on while operator is in the open cycle(running open). CLOSING: LED will be on while operator is in the close cycle(running close). RADIO: LED will turn on while radio input is activated(closed circuit to COMMON). EXIT: LED will turn on while EXIT input is activated(closed circuit to COMMON). PHANTOM: LED will turn on while PHANTOM input is activated(closed circuit to COMMON). SAFETY: LED will turn on while SAFETY input is activated(circuit is open from COMMON). PED-SW: LED will turn on while PED-SW input is activated(circuit is open from COMMON). 3BT: LED will turn on while 3BT input is activated(closed circuit to COMMON). EDGE: LED will turn on while EDGE input is activated(closed circuit to COMMON). TIMER LED: LED will blink when timer is counting (on the open position only). CHRG: LED turns on when battery is charging. 26 EMERGENCY RELEASE Procedures to open gate for SL-100DC. 1. Turn power OFF. 2. Our gear box has a 10 to 1 ratio so it allows you to push gate open. Procedures to release gate for SL-150DC. 1. Turn power OFF. 2. Push pedal down & move pedal slightly to the left to hold pedal down in position. 3. Push gate open. EXIT OFF 115VAC SAFETY LIMIT SWITCHES 27