Download Mazda 2002 Tribute User manual
Transcript
REV.050614 BLUETOOTH INTERFACE FOR SELECT 2002-UP MAZDA VEHICLES BEEMZ-30 work. Following these instructions from “Start” to” Finish” will ensure 9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help. IMPORTANT: NOT COMPATIBLE WITH PREMIUM SOUND SYSTEMS (AMPLIFIED SYSTEMS) APPLICATIONS Mazda 2011 - 2012 2004 - 2011 2012 - 2014 2006 - 2010 2012 - 2014 2003 - 2011 2006 - 2011 2004 - 2011 2002 - 2006 2007 - 2011 2006 - 2007 2007 - 2011 2007 - 2011 2008 - 2011 Mazda2 Mazda3 Mazda3* Mazda5 Mazda5* Mazda6 MX-5 Miata RX-8 MPV Speed3 Speed6 CX-7 CX-9 Tribute Notes: *Important: These applications require the installer to place a Diode on the 24-Pin White harness, from the Crux T-Harness. See slip sheet included in the Manual for further information & instructions. **2008-2010 Tribute requires a different harness: Crux Part Number 3196; must be special ordered. PRELIMINARY: - Disconnect the positive(+) battery cable for radios that are non-navigation. Radios that are navigation ready should not disconnect the battery cable. Please use caution when installing. Do not install the interface near or on the vehicle’s HVAC system. This will prevent overheating and condensation build up. Use overview to help you determine installation method. INSTALLATION 1. Remove the factory radio to gain access to the factory radio wiring connectors. 2. Disconnect the factory connectors from the rear of the factory radio. 3. Connect the male connectors of the interface power harness into the factory radio. 4. Reconnect the factory connectors into the mating connectors of the interface harness. 5. Connect the male 3-pin connector into the pigtail connector. 6. Route the microphone to a desired location, (for example near the rear view mirror). 7. Re-install a factory radio back into the vehicle’s dash. INITIAL PAIRING TO THE VOICE PROMPTS: 1. READY (POWER ON) 2. SEARCHING PHONES (FOR PREVIOUS PAIRED PHONES) 3. PLEASE SEARCH AND SELECT THE “BEE LINE” DEVICE FROM MOBILE PHONE AND ENTER “0000”. 4. YOU ARE NOW READY TO USE THE HF SYSTEM. Note: The Bluetooth interface will remember up to the last 8 devices. Note: If an incoming call is answered from the mobile phone’s keypad, the call will direct itself to the headset on the mobile phone. To re-direct the phone call to the Crux interface, it must be done directly from the mobile phone. Note: When transferring a phone call to the mobile phone for privacy, the user must re-connect the Crux interface and the mobile phone by selecting the module from the device menu on the phone. Note: If after ending a call the radio is powered “OFF”, you must power “ON” the radio to regain volume control. power back on to re-attempt, if unsuccessful please contact our tech support line. AUTO RE-CONNECT: 1. The BEEMZ-30 module will automatically re-connect the a previously paired mobile phone when the ignition is turned “ON” to the vehicle and the mobile phone’s Bluetooth feature is also on. 24-PIN SAT CD MEDIA SCAN AUTO 2 3 4 5 6 SUPPORTED RADIOS FM1/2 (female plug) AM 1 AM CD MD/TAPE CLOCK LOAD TRACK/SEEK FIG. 1 (Multi-PIN CONNECTORS): TO FACTORY HARNESS FM1/2 SEEK TRACK APC Note: The Bluetooth module will re-connect with the last mobile phone’s it was paired with. If no mobile phone is not found, it will revert to the pairing process. DISC/FOLDER REPLAY 1 TO FACTORY RADIO 24-PIN (male plug) 2 FM AM 4 CATEGORY 5 AUX VOL PUSH AUTO-M TEXT AUTO-M POWER 1DISC 2 DISC 3 RPT 4 5 PROG RDM 6 TUNE PUSH 3 SAT/BT SCAN SEEK TRACK APC CD 6 PUSH H AUDIO CONT. SAT POWER VOLUME PUSH M DISP/ESN AUDIO CONT TUNE RDM 00 SCAN RPT 12-PIN (male plug) 24-PIN (male plug) USING THE STEERING WHEEL CONTROL BUTTONS MIC 3-PIN (male plug) BALL JOINT H WMA MOUNTING THE MICROPHONE 1. Insert the mounting clip into the ball joint on the microphone. 2. Mount the clip on your visor or near the rear view mirror. 3. Route the remaining cable along the edge of the roof liner and towards the back of the radio, hiding the cable from sight. :00 M AM FM1/2 SIRIUS AUX CD FOLDER DISC CAT SEEK TRACK FOLDER DISC CAT 1 RPT TUNE FILE 2 4 RDM 5 TEXT/ESN AUTO-M PRESS SEEK UP BUTTON ONCE END A CALL PRESS SEEK DN BUTTON ONCE REJECT PRESS SEEK DN BUTTON ONCE PRESS SEEK UP BUTTON ONCE SWITCH BETWEEN CALLS PRESS SEEK UP BUTTON ONCE 3 INCREASE VOLUME PRESS VOLUME UP ONCE 6 DECREASE VOLUME PRESS VOLUME DN ONCE PRIVACY MODE PRESS SEEK UP ONCE PUSH DISP HOLD SEEK DN FOR 2 SECONDS ANSWER ANSWER SECOND CALL MP3 LOAD SEEK TRACK VOICE DIAL SCAN Note: Premium Audio Systems need to “Turn On” the radio for handsfree audio to be heard. All features of this module may vary by mobile phone manufacturer. For questions on your mobile phone’s features, please reference the mobile phone’s user manual for information. BLUETOOTH INTERFACE FOR SELECT 2002-UP MAZDA VEHICLES BEEMZ-30 IMPORTANT: NOT COMPATIBLE WITH PREMIUM SOUND SYSTEMS (AMPLIFIED SYSTEMS) APPLICATIONS Mazda 2011 - 2012 2004 - 2011 2012 - 2014 2006 - 2010 2012 - 2014 2003 - 2011 2006 - 2011 2004 - 2011 2002 - 2006 2007 - 2011 2006 - 2007 2007 - 2011 2007 - 2011 2008 - 2011 Mazda2 Mazda3 Mazda3* Mazda5 Mazda5* Mazda6 MX-5 Miata RX-8 MPV Speed3 Speed6 CX-7 CX-9 Tribute Notes: *Important: These applications require the installer to place a Diode on the 24-Pin White harness, from the Crux T-Harness. See slip sheet included in the Manual for further information & instructions. **2008-2010 Tribute requires a different harness: Crux Part Number 3196; must be special ordered. USING THE MENU STRUCTURE: To enter the Voice Menu you must do the following: 1. Hold Seek Down fro 2 seconds. 2. Press Seek Up once. 3. Hold Seek Down fo 2 seconds. You are now at the top of the menu. 4. Press Seek Down to scroll though the menu options. 5. Press Seek Up to select a menu option. VOL SETTING TTS VOLUME: Continue to press the “SEEK DN” button twice till you hear the interface announce “SETTING VOLUME”, and wait for her announcement. 3. Set the TTS volume by pressing the volume Vol+ and Vol- waiting for the announcement. Each announcement will indicate the volume level of the TTS. 4. When the desired volume level is reached, press the “SEEK UP” button once to select. DELETE ALL PAIRED DEVICES: This feature allows you to delete all paired devices on the interface. The module does NOT allow the user to only clear one device. The module will delete all previously paired devices only Continue pressing the “SEEK DN” button twice till you hear the interface announce “DO YOU WANT TO DELETE PAIRED PHONE LIST”. 4. The interface will ask “ARE YOU SURE”, press the “SEEK UP” Note: The menu structures only remember the last 24 numbers in the call log from dialed from the mobile phone. Note: All menu structures work in 3 second increments. If after 3 seconds the interface will time-out. Are you experiencing random static interuptions durring your phone calls? Remove the battery on the mobile device for a minimum of 15 Seconds. Have you paired your mobile device, and get no sound from the radio? Try reseting the TTS volume setting. With the phone paired to the UBT, enter the “SETTING TTS VOLUME” under menu structure. The default level is at volume 4. MODE - MODE VOL + - MODE INCOMING CALLS: Continue to press the “SEEK DN” button till you hear the interface announce “INCOMING CALLS”, and wait for the numbers to be announced. 3. When the number you wish to dial is announced, press the “SEEK UP” button once to make the call. PHONE MUST BE UNPAIRED TO ENTER THE FOLLOWING MENU STRUCTURE Delete all paired devices on your mobile device and on the UBT. (See Using The Menu Structure) + HF MISSED CALLS: Continue to press the “SEEK DN” button till you hear the interface announce “MISSED CALLS”, and wait for the numbers to be announced. 3. When the number you wish to dial is announced, press the “SEEK UP” button once to make the call. OUTGOING CALLS: Continue to press the “SEEK DN” button till you hear the interface announce “OUTGOING CALLS”, and wait for the numbers to be announced. 3. When the number you wish to dial is announced, press the “SEEK UP” button once to make the call. Have a bad connection when using the A2DP or Handsfree MODE VOL + -