Download CDA WC140 dishwasher
Transcript
WC140 Integrated Dishwasher Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu rtant Important The CDA be Group cannot be responsible injuries losses caused incorrect of usethis or installation of this Group Ltd cannot heldLtd responsible forheld injuries or lossesforcaused byor incorrect use or by installation Please note CDA reserve the right to invalidate thewith guarantee supplied with thisincorrect product following incorrect Please noteproduct. that CDA reserve thethat right to invalidate the guarantee supplied this product following installation or misuse of the appliance. on or misuse of the appliance. This appliance is not to be used bychildren) people (including children) withsensorial reducedor physical, iance is not designed to be useddesigned by people (including with reduced physical, mental sensorial or mental or who lack experience it, unless they have had supervision or instructions on how to use or who lackcapacity, experience or knowledge aboutorit,knowledge unless theyabout have had supervision or instructions on how to use the appliance by someonefor who is responsible for their safety. ance by someone who is responsible their safety. Under no circumstances anyremoved externalfor covers be removed for servicing or maintenance circumstances should any external should covers be servicing or maintenance except by suitably except by suitably personnel. qualified personnel. Appliance information: ce information: Please the details on the appliance rating plate below forCDA reference, to assist Customer ter the details on enter the appliance rating plate below for reference, to assist Customer CareCDA in the event of Care a in the event of a fault with your appliance to register your appliance for guarantee purposes. your appliance and to register your and appliance for guarantee purposes. ce Model Appliance Model umber Serial Number Thisdesigned appliancefor hasdomestic been designed forCommercial domestic useuse only. will invalidate the warranty. ance has been use only. will Commercial invalidate theuse warranty Declarations of Conformity: rations ofCE Conformity: This designed, appliance has been designed, constructed and marketed in compliance with safety ance has been constructed and marketed in compliance with safety requirements of EECrequirements Directives of EEC Directives 89/336/EC, 2006/95/EC, IEC436/DIN44990, EN 50242 EC, 2006/95/EC, IEC436/DIN44990, EN 50242 IMPORTANTFOR INFORMATION FOR CORRECT DISPOSAL OFINTHE PRODUCT INWITH ACCORDANCE WITH EC ANT INFORMATION CORRECT DISPOSAL OF THE PRODUCT ACCORDANCE EC DIRECTIVE 2002/96/EC. VE 2002/96/EC. At thelife, endthe of product its working life, product must be taken to a special authority waste collection d of its working must bethe taken to a special local authority wastelocal collection centre or to a dealercentre or to a dealer appliance recycling services. appliance providing recycling services. Disposing of appliance separately avoids possible negative for the environment Disposing of aahousehold household appliance separately avoids possible negative consequences for thehealth environment and health g of a household appliance separately avoids possible negative consequences forconsequences the environment and and health. It also enables thedisposal constituent materials to constituent betorecovered, saving and resources. a deriving from inappropriate and enables the materials to beenergy recovered to obtain As significant savings rom inappropriate disposal and enables the constituent materials be recovered to both obtain significant savings reminder of need household appliances separately, the product is marked with a crossed-out in energy andthe resources. As a reminder of the need to dispose of household appliances separately, the product is marked and resources. As a reminder of to thedispose need toofdispose of household appliances separately, the product is marked with a crossed-out ossed-out wheeled dustbin. wheeled dustbin. wheeled dustbin. rtant Important • Read prior toof installation and use of the appliance. the instructions priorthe to instructions installation and use the appliance. • Do climb on the open dishwasher door to prevent damage. ot lean or climb onnot the lean openordishwasher door to prevent damage. • Close dishwasher door accidents. after use to prevent accidents. the dishwasher doorthe after use to prevent • Use detergents, salt and designed rinse aid specifically designed for dishwashers. nly detergents, salt only and rinse aid specifically for dishwashers. • Do notdishwasher put solvents in the dishwasher detergent compartment to prevent risk of explosion ot put solvents in the detergent compartment to prevent risk of explosion • Only put dishwasher safe items into dishwasher. If in doubt, check with of the items. put dishwasher safe items into the dishwasher. If in the doubt, check with the manufacturer of the the manufacturer items. • Takethe care when loading the dishwasher to observe thefor recommendations for best are when loading dishwasher to observe the recommendations best loading practice, andloading also to practice, ensure and also to ensure thatassharp such blade as knives aretoplaced blade down to prevent accidents. harp objects such knivesobjects are placed down prevent accidents. Do not open dishwasher door iswhen a programme is running. it isthen necessary to do so, then open it ot open the•dishwasher doorthe when a programme running. If it is necessary to doIf so, open it slightly to allow the dishwasher to pause programme andspilling prevent anyRemember water spilling ightly to allowonly the dishwasher to pause the programme and the prevent any water out. thatout. the Remember that the water thevery dishwasher very hot when the programme is running. in the dishwasher caninbe hot whencan thebeprogramme is running. • When dishwasher is not inthat use, you we reccomend you turn off thesupply water supply the supply tap and disconnect the dishwasher is notthe in use, we reccomend turn off thethat water supply at the tap andatdisconnect the main supply. ain supply. you are leaving dishwasher for you an extended period should leave thetodoor slightly are leaving•theIfdishwasher for anthe extended period should leave theyou door slightly open prevent the open to prevent the formation tion of unpleasant smells.of unpleasant smells. Recommendations Recomendations • To reduce energy and toto loading thethe dishw• • and water waterconsumption, consumption,remove removeallalldirt dirtresidues residuesfrom fromthe thedishes dishesprior prior loading dishwasher. • Only run the when loaded. • the dishwasher dishwasheronly when fullyfully loaded. • • Place Place hollow hollow items items (bowls, (bowls,glasses glassesand andpans) pans)face facedown downininthe thebasket. basket. Before first use • Set the water softener level as required by the water hardness in the area. • Add 2kg of salt into the salt compartment and then fill with water to the top of the salt compartment. • Remove all the packaging materials from the interior of the dishwasher. • Fill the rinse aid compartment. • Run a hot programme without any dishes in the dishwasher. Control Panel Power Button To switch the power to the dishwasher on or off, press the power button (1). When you switch on the dishwasher, the end of programme light will illuminate. illumnate. Programme Selection Button To select a programme, press the programme selection button (2). The dishwasher will store in its memory the last programme used. To change the programme, press the programme selection button again until the light next to the required programme is illuminated. Delay Timer Button and Delay Timer Indicator Lights The dishwasher is equipped with a variable delay timer of three, six or nine hours’ duration. To set the delay timer, press the delay timer button (3). This will switch on the delay timer for three hours, and the 3h light will illuminate. To change the duration, press the delay timer button again until the light next to the required time (6h or 9h) is illuminated. To cancel the timer, press the delay timer button again until none of the delay timer indicator lights are illuminated. As the delay timer counts down, the delay timer indicator lights will illuminate in turn, so at six hours’ delay the 6h light will illuminate, and at three hours’ delay the 3h light will illuminate. Salt Warning Light When the dishwasher salt begins to run out, the salt warning light will illuminate to advise that the salt needs refilling. Rinse Aid Warning Light When the rinse aid begins to run out, the rinse aid warning light will illuminate to advise that the salt needs refilling. End of Programme Light When the programme is complete, the dishwasher will emit five beeps and the end of programme light will illuminate. 2 Power button 1 3 Programme selection button Delay timer button Indicator lights Starting a programme • Press the Power button. • Press the Programme Selection button until the required programme light is illuminated. • If required, press the Delay Timer button. • Once the power is switched on, the end of Programme Indicator light will switch on. • Once a programme is selected, the end of Programme Indicator light will switch off, and the Programme Indicator light will switch on. • When you close the dishwasher door the programme will start automatically. Please note: The dishwasher stores the most recently used programme in its memory. To change the programme, simply press the Programme Selection button . Programme Selection button Power button Delay Timer button End of Programme Indicator light At the end of a programme If possible, do not open the dishwasher door once the programme has started. At the end of the programme, the dishwasher will beep five times, and the end of Programme Indicator light will switch on. Changing a programme It is possible to change the programme if necessary once the programme has started. • First open the door slightly to reduce the risk of water spillage. • Press the Programme Selection button until the required Programme Indicator light is illuminated. • Then close the door. The dishwasher will begin the new programme from the point at which the old programme stopped. Cancelling a programme It is possible to cancel the programme once the programme has started. • First open the door slightly to reduce the risk of water spillage. • Press and hold the Programme Selection button for approximately three seconds, until the end of Programme Indicator light flashes and the Programme Indicator light switches off. • Then close the door. The dishwasher will drain for approximately thirty seconds. Once this is complete, the dishwasher will beep five times and the end of Programme Indicator light will switch on. Switching the dishwasher off • Once the dishwasher beeps five times, and the end of Programme Indicator light switches on, the dishwasher can be switched off by pressing the Power button. • Then turn off the water tap and remove the plug from the power socket. Please note: The dishwasher will automatically continue on the programme it has started if the door is opened or in the event of a power cut. 1. Push the latch as shown in figure 1. 2. Add the required amount of detergent. The main detergent compartment “b” (figure 2) has lines to allow for specific amounts of detergent. These are marked at either 15 cm3 or 25 cm3, to be used depending on how dirty the dishes are. If your dishes are in need of an intensive wash, then add 5 cm3 of detergent into the prewash section of the compartment “a” (figure 2). 3. Then close the detergent compartment lid until the latch locks. fig 1 Detergent Detergent Please note: You should only use detergents designed specifically for To in filldishwashers. the detergent compartment use To fill the detergent compartment 1. Push the latch as shown in figure 1. 1. Push the latch to open the compartment. Add the required amount of detergent. The main detergent do not put If2.using dishwasher always use the detergent compartment, 2. Add the requiredtablets, amount of2) detergent. The mainfor detergent compartment compartment “b” (figure has linesorto allow specific amounts of them in the main body of the dishwasher in the cutlery basket. The solubility (bdetergent. in figure 1)These has lines allow for specific15amounts of detergent. areto marked at either cm3 or 25 cm3, to be of dishwasher tablets can vary depending on the temperature and duration of 3, depending on how dirty used are depending on how dirty the3 or dishes are. theThese marked at either cm 25 cm programme. As a result, it is15recommended that powder detergents should 3 of be used the dishes are. If your dishes are in need of an intensive wash, then add 5 cm in the shorter programmes to allow better performance. into prewash section of the compartment 2). If detergent your dishes arethe in need of an intensive wash, then add 5“a” cm3(figure of 3. Then close the detergent compartment lid until the latch locks. CDA detergent into the sectiondetergent, of the compartment in figure 1).salt recommends the prewash use of separate rinse aid and(adishwasher rather than combination tablets as separateslid achieve better wash performance. 3. Then close the detergent compartment until the latch locks. fig 1 Please note: You should only use detergents designed specifically for Detergent fig 2 fig. 1 use in dishwashers. To fill thedo detergent compartment If you use combination add salt and designed rinse aid tospecifically the dishwasher Please note: You shoulddetergents, only use detergents for 1. use Push the latch as figure 1. and then adjust theshown water in hardness setting and rinse aid setting to the in dishwashers. If using dishwasher tablets, always use the detergent compartment, When you then use separate detergents again, you shoulddo fillnot theput 2. minimum. Add the amount of detergent. The detergent them in required the main body of the dishwasher or in main the cutlery basket. The solubility salt and rinse aid“b” compartments, adjust the waterfor hardness setting to the compartment (figure 2) has lines to allow specific amounts of of dishwasher tablets can vary depending on the temperature and duration of Ifmaximum using dishwasher tablets, always use theadjust detergent compartment, do not put and runAs an wash, then the hardness setting and 3 orwater 3, to the programme. result, it is powder detergents should detergent. These areaempty marked atrecommended either 15incm 25 cm be them in the main body of the dishwasher or thethat cutlery basket. The solubility the rinse aid setting to the appropriate level. be used in the shorter programmes to allow better performance. used depending on can how dirty the dishes of dishwasher tablets vary depending onare. the temperature and duration of the programme. Asina result, it is thatthen powder detergents If your dishes are need of anrecommended intensive wash, add 5 cm3 of should Salt be usedrecommends in the shorter programmes to allow performance. detergent into the the prewash ofdetergent, thebetter compartment “a”dishwasher (figure 2). salt CDA use ofsection separate rinse aid and rather than combination tablets as separatesneeds better wash performance. ensure thethe best efficiency, the dishwasher soft water. Hard water 3. To Then close detergent compartment lid achieve until the latch locks. means that lime residues on the dishes and theaid interior of the CDA recommends the useremain of separate detergent, rinse and dishwasher salt dishwasher, affecting performance. Theadd softener system designed to If youthan do use combination detergents, salt and rinseisaid to the dishwasher rather combination tablets as separates achieve better wash performance. remove the ions that make the water hard to provide the best quality wash Please note: You should only use detergents designed specifically for and then adjust the water hardness setting and rinse aid setting to the This is achieved byseparate using dishwasher useperformance. in dishwashers. minimum. When you then use detergentssalt. again, you should fill the If salt youand do use detergents, andhardness rinse aidsetting to the to dishwasher rinsecombination aid compartments, adjustadd thesalt water the maximum and the run water an empty wash, setting then adjust water hardness and then adjust hardness and the rinse aid setting to setting the and To add dishwasher salt, follow the steps below: If using tablets, always use the detergent do not thedishwasher rinse aid setting the appropriate level. minimum. When youtothen use separate detergentscompartment, again, you should fill put the them therinse main body ofdishwasher the dishwasher inwater the cutlery basket. Thetosolubility 1. inRemove the lower basketor and then unscrew the salt salt and aid compartments, adjust the hardness setting the of dishwasher tablets can vary depending and duration compartment as shown in figure 1. the temperature maximum and runcap, an empty wash, thenon adjust the water hardness settingofand Salt thethe programme. As a result, itappropriate is recommended that powder detergents should setting to thewith level. 2. rinse Fill theaid compartment dishwasher salt (do not use table salt), carefully To ensure the best efficiency, the dishwasher needs soft water. Hard water be usedtoinprevent the shorter programmes to(figure allow better performance. unnecessary spillage 3). Before first use, you should means that lime residues remain on the dishes and the interior of the fill the compartment with 2kg of dishwasher salt and then fill up the dishwasher, affecting performance. The softener system is designed to salt Salt compartment with water (upwater to the brimtoofprovide the compartment) as shown remove the ionsthe that the hard theand best quality wash CDA usemake of separate detergent, rinse aid dishwasher salt Torecommends ensure the3.best efficiency, the dishwasher needs soft water. Hard water in figure performance. This is achieved by using dishwasher salt. wash performance. rather than combination tablets as separates achieve better means that lime residues remain on the dishes and the interior of the 3. Replace the cap and the lower basket. dishwasher, affecting performance. The softener system is designed to remove the ions that make the the water hard toand provide best quality wash To add dishwasher salt, follow steps below: If you do use combination detergents, add salt rinse the aid to the dishwasher performance. This is achieved using dishwasher salt. 1. Remove the lower dishwasher basket and then unscrew the saltthe warning light on by the control panel illuminates, you should andWhen then adjust water hardness setting and rinse aid settingthe tosalt the shown in figure refill compartment theWhen salt compartment with salt only –1.do not again, add water the salt minimum. you cap, thenasuse separate detergents you to should fill the compartment aftersalt, the first use.adjust 2.add Fill theaid compartment with dishwasher salt (do not usesetting table salt), carefully saltTo and rinse compartments, thebelow: water hardness to the dishwasher follow the steps to prevent unnecessary spillage (figure 3). Before first use, you should maximum and run an empty wash, then adjust the water hardness setting and 1. Remove the lower dishwasher basket and then unscrew thefillsalt fill the compartment with 2kg of dishwasher salt and then up the theYou rinseshould aid setting the appropriate level. immediately after adding salt run ato prewash programme compartment cap, shown into figure 2. of the compartment) as shown compartment withaswater (up the brim dishwasher salt, to prevent any damage to the figure 3. 2. Fillinthe compartment with dishwasher salt (do notdishwasher use table salt),systems. carefully Salt 3. toReplace preventthe unnecessary spillage. Before first use, you should fill the cap and the lower basket. compartment with 2kg of salt and then fill up the saltwater To ensure the best efficiency, thedishwasher dishwasher needs soft water. Hard compartment with water (up tothe thedishes brim of the compartment) as shown means thatthe lime residues remain onthe and the interior of the When salt warning light on control panel illuminates, you should in figure 3. dishwasher, performance. Theonly softener system designed refill theaffecting salt compartment with salt – do not add is water to thetosalt 3.compartment Replace the capmake and remove the ions that thelower water hard to provide the best quality wash after thethe first use. basket. performance. This is achieved by using dishwasher salt. When the saltrun warning light onprogramme the control panel illuminates, youadding should You should a prewash immediately after the salt compartment with salt damage only – doto not add water to the salt dishwasher salt, prevent any the dishwasher systems. To refill add dishwasher salt,to follow the steps below: compartment after the first use. 1. Remove the lower dishwasher basket and then unscrew the salt compartment cap, as shown in figure 1. should run a programme immediately after dishwasher 2. You Fill the compartment with dishwasher salt (do not useadding table salt), carefully salt, to prevent any damage the dishwasher systems. to prevent unnecessary spillageto (figure 3). Before first use, you should fill the compartment with 2kg of dishwasher salt and then fill up the salt compartment with water (up to the brim of the compartment) as shown fig 2 fig. fig21 SALT fig 3 SALT fig 3 3 fig. SALT fig 3 SALT fig 2 Testing strip The washing effectiveness of your machine depends on the softness of the tap water. For this reason, your machine is equipped with a system that reduces the hardness in mains water supply. The washing effectiveness will increase when the system is correctly set. To find out the water hardness level of water in your area, contact your local water board or determine water hardness level by using the test strip(if available). Keep the Run Open the adjustment Softener Wait for Make your machine’s water hardness Shake the 1 min. setting according to the result testing strip testing water testing The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, thethe dishwasher obtained through testing strip. after taking it strip in through strip. is equipped with a system thefor hardness in the mains water supply. The efficiency will increase when the of water. water 1 out your that tap reduces system is correctly set. the water hardness level of your water supply you can use the test strip supplied or forTo 1 find out sec. alternatively contactmin. your local water board. No Lime Very low lime content Low lime content Medium lime content Lime content High Lime content 1. Open the testing strip. Adjusting salt consumption 2. Run water through the tap for one minute. 3. Table Hold theof testing stripHardness in water for one second. Water Level Settings 4. Shake the testing strip after taking it out of the water If the hardness of the water you use is above 90 dF (French hardness) or if you are using well water; you are recommended to use filter and water refinement devices. 5. Wait for one minute 6. Check the number of marks on the strip to see the level of water hardness. If the hardness of the water you use is above 60 63dE dE or or if you are using well water; water; you are recommended to use filter and water refinement devices. Please note: The level of water hardness is preset to level 3. 1. Press and hold down the programme selection button 2. Press the power button to switch on the dishwasher 3. Keep the programme selection button pressed until the five programme indicator lights and the end of programme indicator light flash. 4. To adjust the level, press the programme selection button until the required level is selected. The programme lights will illuminate as in the table of water hardness settings. Hardness level is adjusted level 3 button. as a factory setting. 5. NOTE: To store the selected water hardness level, presstothe power 9 nse Aid RinseRinse Aid Aid fill the rinse aid compartment Rinse Aid To fill theTorinse aidrinse compartment fill the aidcompartment compartment To fill the rinse aid Open the rinse aid compartment by turning and removing the cap as 1. Open the rinse aid compartment by turning and removing the cap 1. Open the rinse aid compartment by turning and removing the as cap as shown in figure 4. 1. Open the rinse aid compartment by turning and removing the cap as inshown shown figurein4.figure 4. in figure 4. until the rinse aid indicator goes dark, Fill the rinse shown aid compartment 2. Fill the rinse aid compartment until the aid rinse aid indicator dark, 2. Fill the rinse aid compartment until the rinse indicator goesgoes dark, 2. Fill the aid compartment until the rinse aid indicator dark, as shown in 5rinse (where a indicates the compartment is empty,goes and figure as shown in figure 5 (where “a” indicates the compartment is empty, and as shown in figure (where a indicates the compartment is empty, and shown in 5 figure 5 (where “b” indicates the compartment is full).a indicates as “b” indicates the compartment is full).the compartment is empty, and “b” indicates the compartment is full). “b” indicates the compartment is full). 3. cap, Replace the cap, theup capwith line the up with the Replace the ensuring theensuring markersthe onmarkers the caponline 3. Replace the cap,the ensuring the markers on the cap up with thethe 3. Replace cap,prior ensuring the markers onback the line cap line up with compartment to screwing the cap in place. compartment prior to screwing the cap back in place. compartment prior to screwing theback cap back in place. compartment prior to screwing the cap in place. fig 4 fig.fig 4 44 fig Rinse Aid Adjustment nse Aid Adjustment The level of rinseAdjustment aid use is preset to 4. You can adjust the level of rinse aid Rinse Aid Rinse Aid Adjustment use by as shown in You figure 6. adjust the level of rinse aid level of rinse aidadjusting userinse is preset tois4.preset can The use 4. can Youadjust can adjust the level of rinse The level oflevel rinseofaid useaid is preset to 4. to You the level of rinse aidaid by adjusting as shown in figure 6. use by adjusting as shown in figure 6. use by adjusting as shown in figure 6. If water stains form on the dishes after a wash, the level should be increased. If blue stains which can be wiped away are left on the dishes after a wah, the water on stains form on after the dishes afterthe a wash, levelbe should be increased. ater stainsIflevel form the dishes a wash, level the should increased. be decreased. If water stainsshould form on the dishes after a wash, the level should be increased. If blue stains which can be wiped away are left on the dishes after wash, the ue stains which can be wiped away are left on the dishes after a wash,athe If blue stains which can be wiped away are left on the dishes after a wash, the level should be decreased. l should be decreased. Please note: Rinse aid ensures better quality wash results and level should be decreased. fig. figfig555 fig 5 increased drying performance. Please note: Rinse aid ensures better quality wash results and ase note: Rinse aid ensures better quality wash results and Please increased note: Rinse aid quality results and drying performance. Always refill theensures rinse aidbetter when the rinsewash aid indicator light on the reased drying performance. control panel is illuminated. increased drying performance. Always refill the rinse aid when the rinse aid indicator light on the ways refillcontrol the rinse aid the rinse aid indicator light on the panel is when illuminated. Always refill the rinse aid when the rinse aid indicator light on the trol panel is illuminated. control panel is illuminated. fig.fig6 6 fig 6 fig 6 Dishwasher Baskets To adjust the height of the upper basket: 1. Open the basket retaining clips, as shown in figure 7, but turning them to the side. 2. Remove the upper basket, and relocate the alternate set of wheels on the runner, as shown in figure 8, pushing the basket back into place. 3. Close the basket retaining clips. fig 7 The images below are designed as guidance as to best practice for loading the dishwasher. Upper basket fig 8 Lower basket Bad loads Standard loading and Test Data Capacity • Upper and lower baskets: 12 place settings. • The upper basket should be adjusted to high position. • Cups should be placed on to the dish rack pins. Detergent / Rinse aid • 5 + 25 cm3, in accordance with EN50242-DIN 44990 IEC 436 (international norms) / Rinse aid dosage adjustment: 4. Programme test • Economic 50°C, in accordance with EN 50242 (international norms.). Programme Listing Programme names and temperatures Intensive 65°C (P1) Normal 55°C (P2) Economic 50°C (P3) Quick 40°c (P4) Prewash No Heat (P5) Type of food waste soups, sauces, pasta, eggs, pilaf, potato and oven dishes, fried foods soups, sauces, pasta, eggs, pilaf, potato and oven dishes, fried foods coffee, milk, tea, cold meats, vegetables, not kept for long coffee, milk, tea, cold meats, vegetables, not kept for long Pre-wash to rinse and loosen residue-awaiting full load-then select a programme Level of soil high medium medium small N/A Detergent amount A: 25 cm3/15cm3 B: 5cm3 A+B A+B A+B A N/A Prewash P re was h P Prewash re was h PPrewash re was h P re was h PPrewash re was h 5 65 0° Co w as h wash 5 0° as h 55Cowwash 5 50 0° Co wash w as h o w as h 540 0° C wash 5 0° CEnd w as h C old r ins e Cold rinse C Cold old r ins e rinse CCold old r rinse ins e CCold old rrinse ins e C old r ins e rinse HHot ot r ins e rinse HHot ot r ins e H ot rrinse ins e Hot Hot H ot rrinse ins e H ot r ins e Dry Dry Dry Dry Dry Dry Dry End Dry E nd End E nd End E nd End E nd E nd Programme duration (mins.) 110 95 150 30 15 Electricity consumption (kW hours) 1,55 1,10 1,05 0,68 0,02 Water consumption (liters) (litres) 17,2 16,5 15,7 12,4 4,5 Warning: Short programmes do not include a drying stage. The values and times provided above have been obtained under laboratory conditions according to relevant standards. This information can change depending on the conditions of the dishwasher’s use and environment (network tension, water pressure, water input temperature and environment temperature). Unplug your machine ime maythat accumulate intemperature, the machine's section.InIncase case such gramme runs at high andwashing start the machine. ofof insufficiency, useand turn off its ta Do not use hard materials when cleani ation; ecial cleansing material available in the market. (Cleansing material produced special to and a dampened cloth. chines bycompartment detergent producers.) etergent without loading any dishes into the machine, select a me that runs at high temperature, and start the machine. In case ofFilters insufficiency, use eaning the seals inavailable the machine eansing material in thedoor, market. (Cleansing material produced towastes have remain Check ifspecial any food any accumulated residues in the door seals, wipe the seals regularly filters. by using a s clean by detergent producers.) If any food wastes are left, remove the mpened cloth. thoroughly under the water tap. g the seals inand the Maintenance machine door, Caremachine, eaning the any accumulated residues in the door seals, wipe the seals regularly by using a ancloth. the filters and spray arms at least you once a week. Before beginning any care or maintenance, should always disconnect the d a. Micr plug your machine and turnsupply, off its starting the cleaning. appliance from the electricity andtap alsobefore turn off the water supply. not use hard materials when cleaning your machine. Wipe with a fine cleaning material gd the machine, a dampened cloth. e filters Door andseals spray arms at least once a week. our machine and turn off its tap before starting the cleaning. ers Wipe the dishwasher door seals regularly with a damp cloth to remove se hard materials when cleaning youronmachine. Wipe eck if any residues. food wastes have remained the coarse andwith fine a fine cleaning material mpenedanycloth. ers. ny food wastes are left, remove the filters and clean them roughlyFilters under the water tap. b. Coa c. Meta To rem clockw fig 9 any food wastes have remained on the coarse and fine You should clean the filters at least once a month. 1. Remove the lower basket. the a. Micro d wastes are left, remove filters Filter and clean them b. Coarse Filter y under2. the water tap. Turn the microfilter anticlockwise and then lift it out as in figure 9. c. Metal/Plastic Filter 3. Remove the coarse filter from the microfilter (figure 10). Todishwasher remove and clean(figure the11). filter 4. Remove the base filtera. from the Micro Filter compartment combination, turn it counter clockwise and take it out by lifting upwards.1 b. Coarse Filter fig 10 You should clean and rinse the filters thoroughly before replacing all the c. toMetal/Plastic Filter should lock into sections in reverse order that above. The microfilter Pull an filter. 3 of the water u metal/p filter in the ma anothe metal/p directio when t seen fr • Never use your dishwasher without • Incorrect fitting of the filter will reduc the metal/plastic To remove thecoarse filter combination, it counter • turn Clean filters are very important in ter filter. 3 and Thenclean pull the filter out clockwise and take it out by lifting upwards.1 of the micro filter.2 Rinse it with lots of Please note: Never run a programme without the filters in place. water under the tap. Refit the Incorrect fitting of the filters may reduce wash performance and metal/plastic filter. Insert the coarse potentially damage your appliance. Pull and the metal/plastic filter remove into the micro filter in a way that filter.the 3 Then coarse filter out markspull willthe correspond to one of the micro filter.2 it with lots another. Attach Rinse micro filter into theof Spray arms watermetal/plastic under the tap. the to the filterRefit and turn You should clean the spraymetal/plastic arms direction at least once aof month. arrow andthe it iscoarse locked filter. Insert themicro arrowfilter on micro filter that can be filter when into the in a way fig 11 1. Remove the lower basket seen from across. 4 to one the marks will correspond place once it is secure as shown in figure Pull and12.remove 2. Pull the lower spray arm upwards to remove it. another. Attach micro filter into the Never use your dishwasher without anyfilter filter. 3. To remove the upper spray arm, first remove the nut on the upper metal/plastic and turn tospray the ncorrect fitting of theitfilter will9.reduce the washing effectiveness. arm by turning as indirection figure of arrow and it is locked Clean filters are very important in terms themicro properfilter running of the machine. when the arrowofon can be You should clean and rinse the spray arms thoroughly before replacing from 4 tightened when them. Ensure that theseen upper spray armacross. nut is securely refitting the upper spray arm. use your dishwasher without any filter. ct fitting of the filter will reduce the washing effectiveness. Dishwasher interior filters are very important in terms of the proper running of the machine. To deal with an accumulation of dirt, oil or limescale in the dishwasher, run 20 is empty. an intensive programme with detergent when the dishwasher Alternatively, there are specialist dishwasher cleaners available that can be used. fig 12 Failure Codes and Troubleshooting Your dishwasher control panel is equipped with a diagnostic display to help in the event of a problem with the appliance. Error Code Intensive Normal Eco Quick Prewash Error description Inadequate water supply Advice Make sure the water inlet tap is fully open Close the water tap, separate the water inlet hose from the tap and clean the filter Restart your machine, contact CDA service if the error resumes Continual fill error Close the tap and contact CDA service The waste water in the machine cannot be discharged. Drain hose is blocked The filters of your machine might be blocked Restart the dishwasher and cancel the programme If the error continues, contact CDA service Heater error Contact CDA service Alarm is active against water overflow Turn off the dishwasher and disconnect the water supply Contact CDA service Faulty electronic card Contact CDA service Overheating error (temperature in the machine is too high) Contact CDA service Faulty heater sensor Contact CDA service Failure Code and Troubleshooting Problem The programme will not start Water remains inside the dishwasher at the end of the programme Possible cause Check the plug, fuse and circuit breakers of the mains supply The water tap is turned off The dishwasher door is not fully closed The water inlet filter or the machine filters are blocked The water drain hose is blocked or kinked. knicked The filters are blocked The dishwasher stops in the middle of a programme Power failure Water inlet failure Programme is on standby Wash performance is of a low standard Poor loading of dishes hinders wash performance. Insufficient detergent added Inappropriate wash programme selected Spray arm blocked Filters clogged or incorrectly fitted Water drain pump blocked White stains on the dishes Insufficient detergent added Rinse aid setting is too low Insufficient dishwasher salt added Water softener setting is too low Salt compartment cap not completely closed The dishes are not completely dry at the end of the programme A programme without a drying stage was selected Rinse aid setting is too low Dishes unloaded too soon (allow time for drying) There are rust stains on the dishes Different sets of cutlery should be kept separate Too much salt (Water softener setting is too high) Salt compartment cap not completely closed Poor appliance earth (check mains electrical supply) The door is not opening or closing properly Door tension not correctly adjusted for the décor door Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of safely to avoid the risk of electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used. As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:• The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELLOW. • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N), or coloured BLACK or BLUE. • The wire which is coloured BROWN must be connected to the terminal which is marked with the letter (L) or coloured RED or BROWN. If in doubt regarding the electrical connection of this appliance, consult a qualified electrician. Do not shorten the supply cable, the appliance may require removing for servicing. N.B. Ensure that the plug socket is situated in an easily accessible place. Installation • Do not install this appliance if it is damaged in any way. Installing a damaged appliance may invalidate the warranty. • The water supply tap should be located in an adjacent cupboard so that it can be accessed after installation. • Ensure the appliance is level by adjusting the feet as necessary. • Only use the water inlet supplied with the appliance. • If the water pressure is above 10 bar, a pressure relief valve should be used. • After connecting the water supply, check to ensure there are no leaks. • The water outlet can either be connected to a water drain or to a sink outlet spigot. This connection should be at a minimum of 50 cm and a maximum fig 14 of 110 cm from the floor. The drain hose should be no longer than 4m in length to ensure good performance from the dishwasher. fig 15 fig 16 To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu CDA Dishwasher – Oversized Fascia Door Mounting Information Scope of Document: Where non-standard integrated appliance doors are supplied, additional fitting instructions are required to ensure compatibility with this product. Instructions: The machine is supplied with a fitting template and these instructions should be followed as normal. However, the fitting template needs to be located lower down the fascia door; this is shown below: - Offset Y Door Height X Fitting Template The amount of offset, Y, depends on the height of the fascia door and can be calculated as: - WC140: WC350, WC360: X-723mm X-725mm For example, if you have a 731mm tall fascia door and are fitting a door to a WC140, then Y = 731 – 723 = 8mm MT 11/06/09