Download KitchenAid 9743822 Dishwasher User Manual

I itChenAid
®
HOME APPLIANCES
APPAREILSI_LECTROM_:NAGERS
www.kitchenaid.com
_---------._
Quick Reference
Section
Introduction
\
Page
2
Product dlmenslons
3
Bullt-ln opening dlmenslons
Electrical requlremonts
Water requlrements
Draln requlrements
Installation steps
Need assistance?
3
4
4
4
5 Back cover
The KitchenAid Consumer Assistance Centeris open 24 hoursa
day,7 daysa week. Call 1-(800) 422-1230. The call is free withinthe
continental UnitedStates.In Canada,call 1-(800) 461-5681 for
English,and 1-(800) 461-5703 for French.
Call t_ KitchenAtd Consumer Assistance Centerwhen you:
Havequestionsaboutdishwasherinstallationor operation.
1_ Needto obtainthe nameand numberofa KitchenAid-authorized
service
company,
Important:
• Installer:. LeaveInstalLationInstructions withthe homeowner.
• Homeowner: KeepInstallationInstructionsfor future
reference.
• Save InstallationInstructionsfor local electricalinspector's use,
PartNo. 9743822 Rev,C
Piece n° 9743822 R_. C
In_on
s_s cont fmm _
s
If connecting dishwasher with power
check that power supply is dlsconne_ed.
supply cord,
ElectricalShockHazard
PlugIntoa grounded3 prongoutlet.
Do not removegroundprong.
Do not usean adapter.
Do not usean extansloncord.
Failureto followthese InstructionscanresultIn death,fire,
or electricalshock.
• Usepowersupply cord kit (Part No. 4317824) available fromyour
dealer or partssupplier.Followinstructionswithkit for installing
powersupply cord.
If the cord kitis notacailable,a U.L.-listed/CSA-cerlifled,
16-gauge,
three-conductor,power supplycord and m.ainreliefmust be
used. Six feet (1.8m) must be the maximumlengthof power
supply cord.
• Routepower supplycord so itdoes not touchdishwashermotoror
lowerpartofdishwasherrob.
_
*Remove
thedishwasher
terminal
boxcover(O).
• Installa U.L.÷listed/CSA-certilied
strain relief(P) to the terminal
box. Run power supplycord throughstrain relief.
®
A. electric drill
N. level
B. Phillips screwdriver
C. flat-blade screwdriver
O. safety glasses
D. 2 adjustable wrenches
E. pliers
R. Teflon tape
S. Drain tube adapter
Part No. 9741366
(available from your
dealer) if connecting to a
1/2" I.D. drain line.
F. measuring tape or ruler
G. pipe wrench
H. hole cutters (1/2", 3/4",
t-ln")
1. tubing cutter
J. wire stripper
K. utility knife
L. 1 1/32" and 1/4" nut driver
or hex socket
M. 2 twist-on wire connectors
P. gloves
Not shown:
90 ° elbow with 3/8" N.P.T.
external threads on one
end. The size of the other
end must fit your water
supply line.
for 16-gange wire
A. 2 drain hose clamps
B. 2 No.-lO x 1/2" Phillips-head screws
Remove parts from bag. Check that all parts were supplied.
2
/
(6xem)
34"(S6._)
Unshaded area must be free ofpipes, wires anddrain hose.
Power supply cord or cable shouldnot be kinkedor pinchedbetwom
dishwasherandcab'met.
Leveling legs and wheels adjust to fit34-inch (86.4cm) to 35-inch
(88.9cm) cabinet opening height. Iflevelinglegsand wheels are removed
from dishwasher, 33-13/16inches (85.9cm) is the minimum cabinet opening
height.Measure thisdistance from the lowestpoint ofthe underside ofthe
countertop.
Corner locations requirea 2"(5.1cm) minimum clearancebetween side of
dishwasherdoor and the wallor cabineL
Checklocation where dishwasherwill be installed.Do Notinstalldishwasher
over carpeting.Thelocation must provide:
• Protection so that the water inlet and drain lines cannot freeze.
Damagefromfreezingis notcoveredbythe warranty.If dishwasher will
be subject to freezing temperatures and leftunused fora periodof
time, see "Winterizing"instructions in your Useand Care Guide.
• Easyaccess to water,dectvidtyand drainage lines.
• Convenientloading.The best location is to the rightor left of a sink
• Asquareopening for proper dishwasheroperation and appearance.
* Acalfmetfruntthatis perpendicular to the floor.
• 1/4"(.64cm) minimumclearancebetween motor and flooringto prevent the
motor from overheating.
• The hot water line to the dishwasher must provide between 20-125
psi (138-862 kPa) water pressure.
• The hot water heater should be set to deliver 120°F (49°C)
minimum water temperature to the dishwasher for best results.
• A 3/8" minimum O.D. copper tubing inlet line is recommended.
• Dishwasher inlet valve has 3/8" N.P.T. internal pipe threads.
• Allsolder connections must be made before water line is connected
to dishwasher inlet valve. Do Not solder within 6 inches (15.2cm)
of inlet valve.
20-(so.san)
The drainhose suppliedmeets AHAMDW-i teststandards.
• The drain hose musthave a high drain loop, 20 inches (50.8cm)
abovefloor.This willhelp toprevent backflowor water siphoning
during dishwasheroperation.
• An'airgap must be used in the high drain loop ffthe drain hose is
connectedto house plumbinglower than20 inches (50.8cm).
• The wastetee or disposer inlet must be 20 inches (50.8cm)
minimumabovethe floor.
• Drain hose must be installed to wasto tee or inlet above drain trap in
house plumbing.
• Drain line and fittings must be 1/2" minimum I.D.
• ff a longer drain hose is required, the _um
length is 12 feet
(3.7m). Check that drain hose is resistant to heat and detergent.
Direct wire method
Localcodes maypermitusingarmored ornon-metallicsheathed,
copper wire(A) (withgroundwire) to connectdishwasherto
unctionbox.
5. Cut a 3/4"(l.gcm) hole in la_, side or floorof cabinet(B) for
directwiring.Rightside is easiestlocation.
Wood cabinet: Sandhole untilsmooth.
Metal cabinet: Coverhole withgrommet (Part No.302797)
availablefrom your dealeror parts supplier.
6. Install a U.L-listed/C_A-certffied strain relinfto the junction box.
If using conduit, use a Ui.-listed/CSA-cer tiffed conduit connector.
Connect the power supply wire to the junction box. Run the other
end of wire through cabinet hole (B). The power supply wire
must extend 24 inches (61cm) from the back wall into cabinet
opening.
Power supply cord method
Localcodes maypermit a U.L.-listed/_A-cer
tiffed,16-gauge,power
supply cord (PartNo.4317824) (C) with a three-prong,groundtypeplug (D) to connect dishwasherto grounded outlet (E).
5. Cut a 1-1/2"(3.8cm) hole in rear or rightside of cabinet (F) for
powersupplycord. Rightside is easiest location.
Wood cabinet: Sand hole until smooth.
Metal obinet: Coverhole with grommet (PartNo.302797)
availablefromyour dealer or parts supplier.
6. Install a matingthree-pronggronnd-typeoudet in an adjacent
cabinet.
Waterline (protect from freezing)
7. CUta 1/2"(1.3cm) minimum hole (G) in cabinet wall orfloor for
water line. Loftside is easiestlocation.
8. Roughwaterline (H) to the cabinetopening.
9. Install a manualshutoffvalvein the water line whereit can be
easilyused.
10. Flushwater line into a bucket to get rid ofany particles thatmay
cloginlet valve. Check thatthere are no sharp bends or ldnks in
the waterline thatmayrestrictthe waterflow. Turnshutoffvalveto
the "OFF"position.
Drain hose
11. CUta 1-1/2' (3.8on) diameter drain line op_
cabinetwallor floor.
(I) in the
chart. Thedishwashershouldbe installedas levelas possible from
front to back. levelinglegs (E) the numberof turnslistedin the
Adjustthefrout
(G). Push drain hose (H) onto drain connector. Usepliers to open
Put
theand
spring-typedrain
hose
clamp
(F)and
over
theconnector.
drain connector
clamp
slide clamp over
drain
hose
drain
Check
that drain hose is securely attached to drain connector.
Tilt dishwasher backwards on wheels when moving across
floor to prevent damage to floor covering.
Latch (I) the dishwasher door. Grasp the sides of the dishwasher door
near the console (J). Tilt dishwasher backwards on wheels. Move
dishwasher close to cabinet opening. Do Not push on the center of
the console. Discard shipping baseor hardboard.
Insert drain hose into hole cut into caFmet. Checkthatdrain hose
does not contactdoor springs,motor orwater line.
• Do Notrun drain hose over topof tub. Checkthatdrain hose is not
kinked or twisted.
Insert power supply cord into hole cut into cabinet. If using power
supply wire, adjust wire and pull towards dishwasher terminal box.
• Do Not pinch power supply cord or ldnk power supply wire between
dishwasher and cab'met.
m
__
I
m
m
Movedishwashercompletelyinto cabinet opening. Center dishwasher
in opening.Checkthat levelinglegs (K) are firmlyagainstthe floor.
Alignthe dishwasherdoor withfront of cab'metdoors. Checkthat
spacing (L) is the same on both sides.
Altemate Connection Methods
NoAir Gap
Iflocal codes permit,the dishwasherdrainhose maybe connected
direcOy
toawaste
teeorwaste
dispo .
Drain hose (A) to waste tee (B)
Cut drain end of drain hose as shown(C). Do Notcot fibbed
sectionto shortendrainhose (D).
Secure drain hose towaste teewith spring- or screw-type
clamp (E). If spring-typeclamp does not fit smallersectionof
drain hose connector,use a smallerclamp. Smallerdamps are
availableat plumbingsupplystores.
The waste tee connection MUSTbe ahead of the drain
trap (F) and 20 inches (50.8cm) minimum above the
floor (6).
Drain hose (H) to disposer
(I)
Knock out disposer inlet plug from inlet 0)- If inlet plug
fallsinside disposer,youmust removeinlet plug before
connec_ng drainhose. If disposeris alreadyinstalledin sink,
youmay needto removedisposer from sinkto removeplug.
DONOTcutend of drain hose.
Securedrain hose to disposer with spring-or screw-type
damp (X).
Mostdisposershave7/8"connectors,or special connectors are
availableatplumbingsupplystores.
The disposer connection MUSTbe ahead of the drain
trap (L) and 20 inches (50.8cm) minimum above the
floor (M).
7
• Installa U.L-listed/t_-certiliedstrainrelief(F) to the terminal
box. Runpowersupplywire throughstrainrelief,ff usingconduit,
use a U.L.-listed/CA_-cer
tiffedconduit connncmr.Runconduit
through
connector.
• Connectthe whitewire (G) from the power supplywire to the
whitewire in the terminalboxwith twist-onwire connector.
• Connectthe blackwire (H) fi'omthe power supplywire to the
black wire in the terminalbox withtwist-onwire connector.
If the ground connector (I) looks like this:
• Loosenfront nut O) on groundconnectorlocatedon the backof
terminalbox. Do Notloosen the rearnut (K) on the ground
connector.
• Form the baregroundwire (L) into a U-shapedhook. Wrap
ground wire hook clockwisearound ground connectorand
between the rearandfront nuts. Securelytightenthe front nut (J)
overthe groundwire.
• Tightenstrain relief or conduitconnector screws (M).
OR
If the ground connector (i) looks like this:
• Loosenscrew O) onground connector locatedon the backof
terminalbox.
• Formthe bareground wire (K) into a U-shapedhook. Wrap ground
wire hook clockwisearound ground connector and under the
washer(L).Securely
tighten
thescrew0).
• Tightenswainreliefor conduitconnectorscrews (M).
II
®
• Replaceterminalcover (E).
Installation steps cont. on page 9
o
• Connectthe white wire (Q) fromthe powersupplycordto the
whitewirein the terminalbox with twist-onwireconnector.
• Connectthe black_
(R) fromthe power supplycordto the
blackwirein the terminalbox with twist-onwire connector.
If the ground connector (S) looks like this:
• Loosenfrontnut (T) on ground connector locatedon the backof
terminalbox. Do Notloosen the rearnut(U) on theground
connector.
i
• Formthe baregroundwire (V) into a U-shapedhook. Wrap
groundwire hook clockwisearoundgroundconnectorand
betweenthe rearand fi'ontouts. Securelytightenthe front not (T)
over the ground wire.
• Tightenstrain reliefscrews (W).
OR
ffthe ground connector (S) looks like this:
• Loosenscrew (1")onground connector located on the back of
terminalbox.
• Formthebaregronndwire (U) into a U-shapedhook Wrap
ground wire hook clockwisearound ground connectorand under
thewasher(V). Securelytightenthe screw (T).
• Tightenstrainreliefscrews(W).
J
m
I
• Replaceterminalcover (0).
Illl
(o_1
• Plug power supply cord (X) into mating grounded outlet (Y).
Q
Opendoor about 3 inches (7.6cm) and check for equalspacing (C)
between inner door and tub sides. If spacingis notequal, loosen
bracket screwsand shifttub. Tightenbracket screws. Remove
newstraperor towelfrom dishwasher.
O
easily.Ifdoor doses too quicklyor fallsopen, adjust door
Openand
door severaltimes.Thedoor
should
close
springs
(D)close
bymovingspringends
to different
holes open
(£) inand
base.
tN
access andlower panelto dishw_her so thatthe bottomedge
of the lower panelcontactsthe floor.
Your installation
is now complete.
Keep Installation
Instructions
and Use and Care Guide
close to dishwasher for easy reference.
Your safety and the safety of others
is very Important.
n
We have provided many important safety
messages in this manual and on your appliance.
Always read and obey all safety messages.
This is the safety alert symbol. This symbol
alerts you to hazards that can kill or hurt
you and others. All safety messages will be
preceded by the safety alert symbol and the word
"DANGER" or "WARNING". These words mean:
You will be killed or seriously Injured if you
don't follow instructions.
You can be killed or seriously injured if you
don't follow instructions.
All safety messages will identify the hazard,
tell you how to reduce the chance of injury, and tell
you what can happen if the instructions are
not followed.
• Observe
all governing
codes
and ordinances.
• complywith the installationspecificationsand dimensions.
• properlyinstall dishwasher.
• makesure you haveeverythingnecessary for proper installation.
• contact a qualifiedinstaller to insure thatthe electrical and plumbing
installationsmeet all national and local codes and ordinances.
Keep cardboard shipping base or hardboard under
dishwasher until it is installed. The shipping base or hardboard will help Io protect floor covering when
dishwasher is moved across the floor during installation.
Introduction cont.from page2
A*
91-
24"(61cm)* --
35-7.'8"
(_)
MODELS
MODI_LIES
a_.
A
KUDC Series
Stifle KUDC
10UDI25 Series
Sl_de KIJDI25
24-1/4" (61.6 ore)
61,6 cta (24-1/4 po)
All Others
TOllS lea anwes
25-1/4" (64.1 an)
64,1 can (25-1/4 po)
* does not include insulation bhmket
* ne comprend pas l'isolant
19-3/4"
(50.2{_)*
Opening for electrical, drain and water supply lines:
• Mustbeinstalledwithinthe shaded area as specified.
• Should be located as close to the rear wallas possible.
Electrical outlet must be installed in an adj_cut cabinet.
Wiring should not contact the motor or dishwasher legs.
Water line: CutI/2"(1.3cm) diameter opening.
W_ter line Must Not contact the motor or dishwasher legs.
Drain line and power supply cord: Cut I-I/2"(3.8cm) diameter opening.
Direct wire electrical suppl],: Cut 3/4"(1.9cm) diameter opening.
Install a grommet (Part No. 302797) in opening cut in a metal cabinet for
power supply cord or power supplycable.
Dishwasher must be completely enclosed, sides, top and rear. Side panel ldts
are available from your dealer for installing your diswasher at the end of a
cabinet.
Bl_k, Part No. 4378868
White, PartNo. 4378867
Almnnfl
P_rt MO _TP_ql_Q
O}
It is the customer's responsibility:.
To contact a qualified electrician.
To assure that the electrical installation is adequate and in
conformance with all national and local codes and
ordinances.
Ill
Dishwashermust be connectedto theproperelectricalvoltageand
flequencyas specifiedon themodel/serialratingplate.Themodel/serial
ratingplateis locatedbehindthe door on the frontframe of the
dishwasheropening.
• CONNECTWITHCOPPERWIREONLY.
• 120-volt, 60-Hz, AC-unly, 15-ampere, fused electrical supply is
required.
• A time-delay fuse or circuit breaker is recommended.
• It is recommended that a separate circuit serving only this appliance
be provided.
• Some models are already equipped with a power supplycord. If a
power supply cord is not supplied, Power Supply Cord Kit (Part No.
4317824) is available from your local dealer or parts supplier. Follow
the kit instructions for installing power supply cord.
If the kit is not available locally, use a U.L-listed/CA*_-certified,threeconductor, 16-gauge, six foot, power supply cord that meets all local
codes and ordinances. It must be routed so it does not touch the
dishwasher motor or lower portion of the dishwasher tub. A swain
relief must be used to secure the power supply cord to the dishwasher
terminal box. The power supply cord must be plugged into a mating
3-prong, ground-type oudet, grounded in accordance with all national
and local codes and ordinances.
• Ifa powersupplycord is attachedto dishwasherbutyouneed to direct
wiredishwasher,youwill need DirectWireConnectionKit(Part No.
4317979). Removepowersupplycordand make all directwire
connectionsinsideterminalbox. Allelectricalconnectionsmustbe
madein accordancewith allnationaland localcodes and ordinances.
• Dishwashermustbe connectedto a grounded metal,permanent
wiringsystemor a ground conductorcan be usedwith the dt_-'uit
conductorsto connect to the groundterminalor lead on the
dishwasher.
• Do not groundto a gas pipe.
• Do not connectdishwashertoelectricalsupplyuntildishwasheris
permanentlygrounded.
• Do not have a fuse in the neutral or ground circuit.
/
24,,'''_
(61_m)
ElectricalShock Hazard
Disconnectelectrical power at the fuse box
or circuit breakerbox before installing
dishwasher.
Failure to do so can result in death or
electrical shock.
1. Disconnectthe power supply.
2. Putonglovesandsafetyglasses.
Electrical
3. Pick one method to follow("Directwire" or "Power supplycord"),
dependinguponyour dishwasherand local codes.
4. Completewiringto cabinet openingaccording towiring_nethodyou
need. Followalllocal codes and ordinances.
Tip Over Hazard
Do not use dishwasher until completely
installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and Install
dishwasher.
Failureto do so can result in back or other injury.
Keep cardboard shipping base or hardboard under
dishwasher until it is installed.
The shipping base or
hardboard will help to protect floor covering during
installation.
Removethefour screws attachingaccess panel (A) and lower panel
(B) to dishwasherusinga 1/4"hex socket, nut driveror PhiLlips
screwdriver. Removepanels and set panels aside on a protective
surface.
Mill,
Cutout
"" Height
Wheel
Position
(See Illustration)
Number Of Turns
To Adjust
Levelers
34"(s6.4cm)
1
9
34-1/8"
2
6
34-5/16"(87.2cm)
3
3
34-1/2"(87.6_n)
4
0
(86.7c_m)
For additional height:
1. Add shims under the wheels.
2. Turn front levelers (each turn is approximately 1/16"
(1.6ram) in height).
Measure heightof cabinetopening(C) fi'omundersideof countertop
to floor. Checkchartfor thatheight opening. Put wheels(D) in the
requiredposition,
(I
r !
I'1
Connectdrainhose to an air gap orwastetee using one of the
recommendedor alternate methods.
Recommended
Connection
Methods
Install Air Gap Kit (Part No. 300096) (A) according to kit
instructions. If a different air gap is used, it should be checked to
make sure it allows for the same air flow.
Drain hose (B) to air gap (A) to waste tee (C)
Cutdrain cod of drain hose as shown (D). Do Notcut ribbed
sectionto shortendrainhose (E).
,t,
Securedrainhose toair gapwithspring-typeclamp(F). If
spring-typeclampdoes notfit smallersection of drainhose
connector,use a smallerclamp. Smallerclampsareavailableat
plumbingsupplystores.
Connect the air gap towastetee usinga rubberconnector(G)*
and spring-orscrew-typodamps (H).
The waste tee connection MUSTbe ahead of the drain
trap (I) and 20 inches (50.8om) minimum above the
floor O).
Drain hose (K) to air gap (L) to disposer
(M)
Knock out disposer inlet plug (N) from inlet. If inletplug
fallsinside disposer,you must removeinlet plug before
connectingdrainhose. Ifdisposeris alreadyinstalledin sink,
you may need to removedisposerfrom sink to remove plug.
DONOTcut end of drainhose.
Securedrain hose to air gap withspring-typeclamp(0).
Connect the airgapto disposer using a rubberconnector (P)*
andspring- or serew-typoclamps(Q).
Mostdisposershave7/8"connectors,or specia]connectorsare
availableatplumbingsupplystores.
The disposer connection MUSTbe ahead of the drain
trap (It) and 20 inches (50.8cm) minimum above the
floor (S).
* All parts are available from your dealer.
to waterinletvalve(B). Attachwatersupplyline (C) to fitting.
Do
Not
allow the water
pipe or tubingand
to contact
the motor
or
Apply
Teflontapeto
90° elbowfitting(A)
connectfitting
directly
dishwasher legs (D). Turnon watersupplyand check forleaks.
o
Check electrical requirements.
Be sure you have correct
electrical supply and recommended grounding method. See
Page 4.
If connecting dishwasher using direct wire method,
check that power supply is disconnected.
ElectricalShock Hazard
Electricallygrounddishwasher.
Connectgroundwire to green groundconnectorin terminal
box.
Do not usean extensioncord.
Failureto do so can resultin death,fire, or electricalshock.
• Removethe dishwasherterminalbox cover (E).
Tip Over Hazard
Do not use dishwasheruntil completely
installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
bottomrzck Placenewspaper (A) or toweloverbottom of
Opendishwasherdoor
and removeall
shippingmaterials.
Remove
dishwasherto
prevent screwsfrom
fallinginto
pump area when
securingdishwasherto countertop.
ThedishwasherMUSTbe secured to countertoporfloorto keep it
fromtippingwhen door is opened.
Countertop attachment: Secure dishwasherto counter_p with two,
No. 10 x 1/2"Phillips-headscrews(it).
Do Notdropscrewsinto the bottom of the dishwasher.Screws,if
droppedin pumparen,maycausedamageto pumpor motur.
Floor attachment: Usefloor attachmentkit (Part No.4378968)
availablefrom your dealer.
Checkthatall parts havebeen installed (except access and lower
panels) and no steps wereskipped.
_
Checkthatyou have all the tools youused.
Readthe Useand Care Guidethat came with yourdishwasher.
,,Reconnec,
t, power supplyto dishwasher.Setthe dishwasherto runthe
'Normal' cycle.Start dishwasherand allow it to run for 2 minutes.
Opendishwasherdoor. Thewater levelshouldbe deep enoughto
causedieflent(A)mfloat
onthewater,
ffthewaterleveliscorrect,
close the door andallowthe dishwasherto completethe cycle.
_ff
the dishwasherdoes not fallto the proper level,check the following:
• Is the shutoffvalvein the water supply line completelyopen?
• Is the water supplylineblocked or kinked?
Check thatthere ure no water leaks. If thereare waterleaks,
aghten llmngs.
The KltchenAidConsumer Assistance Centeris open 24 hoursa
day,7 daysa week.Call1o(800) 422-1230. Thecallis freewithinthe
continental UnitedSta_. InCanada,call 1-(800) 461-5681 for
Englishand 1-(800) 461-5703 for French.
Call the KitchenAid Consumer Assistance Center when you:
• Havequestionsabout dishwasherinstallationor operation.
1_ Need to obtain thename and number of a KitebenAidauthorizedservicecompany.
If dishwasher does not operate, check these points:
"]ff FI_ the cir_it breaker trippedor the house fuse blown?
• Is the door dosed tightlyand latched?
• Has the cycle been set correctly to start thedishwasher?
Has electrical power been Interrupted?
• Hasdie motor overloaded?It willresetitselfwithin a few
minutes.
If you need service:
Maintainthe qualitybuiltinto your appliancebycallinga KitcbenAidauthorized servicecompany.To obtain the name and number ofan
authorized servicecompany:.
• Contactthe dealer from whom youpurchased the app_ance;
• LookIn the YellowPages ofyour telephone directoryunder
"Appliances-- Household-- Major -- Serviceand Repair;"
• or Calldie KitcbenAidConsumerAssistanceCenter.
When you call, you will need:
II_Thedishwashermodelnumber.
The dishwasher serialnumber.
Bothambers are listedon the model/serialratingplatelocated
behind the door on the _out frame of the dishwasheropening.
Part No.9743822 Rev.C
© 1998 rdtchen_d
*RegisteredTrademark/Trademark
of KitchenAidU.S.A.,
KitchenAidCanadalicenseein Canada
PrintedIn U.S.A.